Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull ACPI and power management updates from Rafael Wysocki:
 "This time we have some more new material than we used to have during
  the last couple of development cycles.

  The most important part of it to me is the introduction of a unified
  interface for accessing device properties provided by platform
  firmware.  It works with Device Trees and ACPI in a uniform way and
  drivers using it need not worry about where the properties come from
  as long as the platform firmware (either DT or ACPI) makes them
  available.  It covers both devices and "bare" device node objects
  without struct device representation as that turns out to be necessary
  in some cases.  This has been in the works for quite a few months (and
  development cycles) and has been approved by all of the relevant
  maintainers.

  On top of that, some drivers are switched over to the new interface
  (at25, leds-gpio, gpio_keys_polled) and some additional changes are
  made to the core GPIO subsystem to allow device drivers to manipulate
  GPIOs in the "canonical" way on platforms that provide GPIO
  information in their ACPI tables, but don't assign names to GPIO lines
  (in which case the driver needs to do that on the basis of what it
  knows about the device in question).  That also has been approved by
  the GPIO core maintainers and the rfkill driver is now going to use
  it.

  Second is support for hardware P-states in the intel_pstate driver.
  It uses CPUID to detect whether or not the feature is supported by the
  processor in which case it will be enabled by default.  However, it
  can be disabled entirely from the kernel command line if necessary.

  Next is support for a platform firmware interface based on ACPI
  operation regions used by the PMIC (Power Management Integrated
  Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
  That interface is used for manipulating power resources and for
  thermal management: sensor temperature reporting, trip point setting
  and so on.

  Also the ACPI core is now going to support the _DEP configuration
  information in a limited way.  Basically, _DEP it supposed to reflect
  off-the-hierarchy dependencies between devices which may be very
  indirect, like when AML for one device accesses locations in an
  operation region handled by another device's driver (usually, the
  device depended on this way is a serial bus or GPIO controller).  The
  support added this time is sufficient to make the ACPI battery driver
  work on Asus T100A, but it is general enough to be able to cover some
  other use cases in the future.

  Finally, we have a new cpufreq driver for the Loongson1B processor.

  In addition to the above, there are fixes and cleanups all over the
  place as usual and a traditional ACPICA update to a recent upstream
  release.

  As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
  Intel platforms should be able to handle power management of the DMA
  engine correctly, the cpufreq-dt driver should interact with the
  thermal subsystem in a better way and the ACPI backlight driver should
  handle some more corner cases, among other things.

  On top of the ACPICA update there are fixes for race conditions in the
  ACPICA's interrupt handling code which might lead to some random and
  strange looking failures on some systems.

  In the cleanups department the most visible part is the series of
  commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
  option.  That was triggered by a discussion regarding the generic
  power domains code during which we realized that trying to support
  certain combinations of PM config options was painful and not really
  worth it, because nobody would use them in production anyway.  For
  this reason, we decided to make CONFIG_PM_SLEEP select
  CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
  became redundant and CONFIG_PM could be used instead of it.  The
  material here makes that replacement in a major part of the tree, but
  there will be at least one more batch of that in the second part of
  the merge window.

  Specifics:

   - Support for retrieving device properties information from ACPI _DSD
     device configuration objects and a unified device properties
     interface for device drivers (and subsystems) on top of that.  As
     stated above, this works with Device Trees and ACPI and allows
     device drivers to be written in a platform firmware (DT or ACPI)
     agnostic way.  The at25, leds-gpio and gpio_keys_polled drivers are
     now going to use this new interface and the GPIO subsystem is
     additionally modified to allow device drivers to assign names to
     GPIO resources returned by ACPI _CRS objects (in case _DSD is not
     present or does not provide the expected data).  The changes in
     this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
     Lu, and Darren Hart with some fixes from others (Fabio Estevam,
     Geert Uytterhoeven).

   - Support for Hardware Managed Performance States (HWP) as described
     in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
     driver.  CPUID is used to detect whether or not the feature is
     supported by the processor.  If supported, it will be enabled
     automatically unless the intel_pstate=no_hwp switch is present in
     the kernel command line.  From Dirk Brandewie.

   - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).

   - Support for firmware interface based on ACPI operation regions used
     by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
     platforms for power resource control and thermal management (Aaron
     Lu).

   - Limited support for retrieving off-the-hierarchy dependencies
     between devices from ACPI _DEP device configuration objects and
     deferred probing support for the ACPI battery driver based on the
     _DEP information to make that driver work on Asus T100A (Lan
     Tianyu).

   - New cpufreq driver for the Loongson1B processor (Kelvin Cheung).

   - ACPICA update to upstream revision 20141107 which only affects
     tools (Bob Moore).

   - Fixes for race conditions in the ACPICA's interrupt handling code
     and in the ACPI code related to system suspend and resume (Lv Zheng
     and Rafael J Wysocki).

   - ACPI core fix for an RCU-related issue in the ioremap() regions
     management code that slowed down significantly after CPUs had been
     allowed to enter idle states even if they'd had RCU callbakcs
     queued and triggered some problems in certain proprietary graphics
     driver (and elsewhere).  The fix replaces synchronize_rcu() in that
     code with synchronize_rcu_expedited() which makes the issue go
     away.  From Konstantin Khlebnikov.

   - ACPI LPSS (Low-Power Subsystem) driver fix to handle power
     management of the DMA engine included into the LPSS correctly.  The
     problem is that the DMA engine doesn't have ACPI PM support of its
     own and it simply is turned off when the last LPSS device having
     ACPI PM support goes into D3cold.  To work around that, the PM
     domain used by the ACPI LPSS driver is redesigned so at least one
     device with ACPI PM support will be on as long as the DMA engine is
     in use.  From Andy Shevchenko.

   - ACPI backlight driver fix to avoid using it on "Win8-compatible"
     systems where it doesn't work and where it was used by default by
     mistake (Aaron Lu).

   - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
     Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
     Chaugule (mostly related to the upcoming ARM64 support).

   - Intel RAPL (Running Average Power Limit) power capping driver fixes
     and improvements including new processor IDs (Jacob Pan).

   - Generic power domains modification to power up domains after
     attaching devices to them to meet the expectations of device
     drivers and bus types assuming devices to be accessible at probe
     time (Ulf Hansson).

   - Preliminary support for controlling device clocks from the generic
     power domains core code and modifications of the ARM/shmobile
     platform to use that feature (Ulf Hansson).

   - Assorted minor fixes and cleanups of the generic power domains core
     code (Ulf Hansson, Geert Uytterhoeven).

   - Assorted minor fixes and cleanups of the device clocks control code
     in the PM core (Geert Uytterhoeven, Grygorii Strashko).

   - Consolidation of device power management Kconfig options by making
     CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
     which is now redundant (Rafael J Wysocki and Kevin Hilman).  That
     is the first batch of the changes needed for this purpose.

   - Core device runtime power management support code cleanup related
     to the execution of callbacks (Andrzej Hajda).

   - cpuidle ARM support improvements (Lorenzo Pieralisi).

   - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
     new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
     Bartlomiej Zolnierkiewicz).

   - New cpufreq driver callback (->ready) to be executed when the
     cpufreq core is ready to use a given policy object and cpufreq-dt
     driver modification to use that callback for cooling device
     registration (Viresh Kumar).

   - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
     Geboski, Tomeu Vizoso).

   - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
     cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
     Stefan Wahren, Petr Cvek).

   - OPP (Operating Performance Points) framework modification to allow
     OPPs to be removed too and update of a few cpufreq drivers
     (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
     during initialization) on driver removal (Viresh Kumar).

   - Hibernation core fixes and cleanups (Tina Ruchandani and Markus
     Elfring).

   - PM Kconfig fix related to CPU power management (Pankaj Dubey).

   - cpupower tool fix (Prarit Bhargava)"

* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
  i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
  dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  tools: cpupower: fix return checks for sysfs_get_idlestate_count()
  drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
  MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  leds: leds-gpio: Fix multiple instances registration without 'label' property
  iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
  block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
  PM: Merge the SET*_RUNTIME_PM_OPS() macros
  ...

13 files changed, 505 insertions, 88 deletions

diff --git a/drivers/cpufreq/Kconfig b/drivers/cpufreq/Kconfig
index 3489f8f5fada..29b2ef5a68b9 100644
--- a/drivers/cpufreq/Kconfig
+++ b/drivers/cpufreq/Kconfig
@@ -63,7 +63,6 @@ config CPU_FREQ_DEFAULT_GOV_PERFORMANCE
 
 config CPU_FREQ_DEFAULT_GOV_POWERSAVE
 	bool "powersave"
-	depends on EXPERT
 	select CPU_FREQ_GOV_POWERSAVE
 	help
 	  Use the CPUFreq governor 'powersave' as default. This sets
@@ -183,6 +182,8 @@ config CPU_FREQ_GOV_CONSERVATIVE
 
 	  If in doubt, say N.
 
+comment "CPU frequency scaling drivers"
+
 config CPUFREQ_DT
 	tristate "Generic DT based cpufreq driver"
 	depends on HAVE_CLK && OF
@@ -196,19 +197,19 @@ config CPUFREQ_DT
 
 	  If in doubt, say N.
 
-menu "x86 CPU frequency scaling drivers"
-depends on X86
+if X86
 source "drivers/cpufreq/Kconfig.x86"
-endmenu
+endif
 
-menu "ARM CPU frequency scaling drivers"
-depends on ARM || ARM64
+if ARM || ARM64
 source "drivers/cpufreq/Kconfig.arm"
-endmenu
+endif
 
-menu "AVR32 CPU frequency scaling drivers"
-depends on AVR32
+if PPC32 || PPC64
+source "drivers/cpufreq/Kconfig.powerpc"
+endif
 
+if AVR32
 config AVR32_AT32AP_CPUFREQ
 	bool "CPU frequency driver for AT32AP"
 	depends on PLATFORM_AT32AP
@@ -216,12 +217,9 @@ config AVR32_AT32AP_CPUFREQ
 	help
 	  This enables the CPU frequency driver for AT32AP processors.
 	  If in doubt, say N.
+endif
 
-endmenu
-
-menu "CPUFreq processor drivers"
-depends on IA64
-
+if IA64
 config IA64_ACPI_CPUFREQ
 	tristate "ACPI Processor P-States driver"
 	depends on ACPI_PROCESSOR
@@ -232,12 +230,9 @@ config IA64_ACPI_CPUFREQ
 	For details, take a look at <file:Documentation/cpu-freq/>.
 
 	If in doubt, say N.
+endif
 
-endmenu
-
-menu "MIPS CPUFreq processor drivers"
-depends on MIPS
-
+if MIPS
 config LOONGSON2_CPUFREQ
 	tristate "Loongson2 CPUFreq Driver"
 	help
@@ -250,15 +245,18 @@ config LOONGSON2_CPUFREQ
 
 	  If in doubt, say N.
 
-endmenu
+config LOONGSON1_CPUFREQ
+	tristate "Loongson1 CPUFreq Driver"
+	help
+	  This option adds a CPUFreq driver for loongson1 processors which
+	  support software configurable cpu frequency.
 
-menu "PowerPC CPU frequency scaling drivers"
-depends on PPC32 || PPC64
-source "drivers/cpufreq/Kconfig.powerpc"
-endmenu
+	  For details, take a look at <file:Documentation/cpu-freq/>.
 
-menu "SPARC CPU frequency scaling drivers"
-depends on SPARC64
+	  If in doubt, say N.
+endif
+
+if SPARC64
 config SPARC_US3_CPUFREQ
 	tristate "UltraSPARC-III CPU Frequency driver"
 	help
@@ -276,10 +274,9 @@ config SPARC_US2E_CPUFREQ
 	  For details, take a look at <file:Documentation/cpu-freq>.
 
 	  If in doubt, say N.
-endmenu
+endif
 
-menu "SH CPU Frequency scaling"
-depends on SUPERH
+if SUPERH
 config SH_CPU_FREQ
 	tristate "SuperH CPU Frequency driver"
 	help
@@ -293,7 +290,7 @@ config SH_CPU_FREQ
 	  For details, take a look at <file:Documentation/cpu-freq>.
 
 	  If unsure, say N.
-endmenu
+endif
 
 endif
 endmenu
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 83a75dc84761..0f9a2c3c0e0d 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -247,3 +247,11 @@ config ARM_TEGRA_CPUFREQ
 	default y
 	help
 	  This adds the CPUFreq driver support for TEGRA SOCs.
+
+config ARM_PXA2xx_CPUFREQ
+	tristate "Intel PXA2xx CPUfreq driver"
+	depends on PXA27x || PXA25x
+	help
+	  This add the CPUFreq driver support for Intel PXA2xx SOCs.
+
+	  If in doubt, say N.
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 40c53dc1937e..b3ca7b0b2c33 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -61,8 +61,7 @@ obj-$(CONFIG_ARM_IMX6Q_CPUFREQ)		+= imx6q-cpufreq.o
 obj-$(CONFIG_ARM_INTEGRATOR)		+= integrator-cpufreq.o
 obj-$(CONFIG_ARM_KIRKWOOD_CPUFREQ)	+= kirkwood-cpufreq.o
 obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ)	+= omap-cpufreq.o
-obj-$(CONFIG_PXA25x)			+= pxa2xx-cpufreq.o
-obj-$(CONFIG_PXA27x)			+= pxa2xx-cpufreq.o
+obj-$(CONFIG_ARM_PXA2xx_CPUFREQ)	+= pxa2xx-cpufreq.o
 obj-$(CONFIG_PXA3xx)			+= pxa3xx-cpufreq.o
 obj-$(CONFIG_ARM_S3C24XX_CPUFREQ)	+= s3c24xx-cpufreq.o
 obj-$(CONFIG_ARM_S3C24XX_CPUFREQ_DEBUGFS) += s3c24xx-cpufreq-debugfs.o
@@ -98,6 +97,7 @@ obj-$(CONFIG_CRIS_MACH_ARTPEC3)		+= cris-artpec3-cpufreq.o
 obj-$(CONFIG_ETRAXFS)			+= cris-etraxfs-cpufreq.o
 obj-$(CONFIG_IA64_ACPI_CPUFREQ)		+= ia64-acpi-cpufreq.o
 obj-$(CONFIG_LOONGSON2_CPUFREQ)		+= loongson2_cpufreq.o
+obj-$(CONFIG_LOONGSON1_CPUFREQ)		+= ls1x-cpufreq.o
 obj-$(CONFIG_SH_CPU_FREQ)		+= sh-cpufreq.o
 obj-$(CONFIG_SPARC_US2E_CPUFREQ)	+= sparc-us2e-cpufreq.o
 obj-$(CONFIG_SPARC_US3_CPUFREQ)		+= sparc-us3-cpufreq.o
diff --git a/drivers/cpufreq/arm_big_little.c b/drivers/cpufreq/arm_big_little.c
index a46c223c2506..e1a6ba66a7f5 100644
--- a/drivers/cpufreq/arm_big_little.c
+++ b/drivers/cpufreq/arm_big_little.c
@@ -289,6 +289,8 @@ static void _put_cluster_clk_and_freq_table(struct device *cpu_dev)
 
 	clk_put(clk[cluster]);
 	dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table[cluster]);
+	if (arm_bL_ops->free_opp_table)
+		arm_bL_ops->free_opp_table(cpu_dev);
 	dev_dbg(cpu_dev, "%s: cluster: %d\n", __func__, cluster);
 }
 
@@ -337,7 +339,7 @@ static int _get_cluster_clk_and_freq_table(struct device *cpu_dev)
 	if (ret) {
 		dev_err(cpu_dev, "%s: failed to init cpufreq table, cpu: %d, err: %d\n",
 				__func__, cpu_dev->id, ret);
-		goto out;
+		goto free_opp_table;
 	}
 
 	name[12] = cluster + '0';
@@ -354,6 +356,9 @@ static int _get_cluster_clk_and_freq_table(struct device *cpu_dev)
 	ret = PTR_ERR(clk[cluster]);
 	dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table[cluster]);
 
+free_opp_table:
+	if (arm_bL_ops->free_opp_table)
+		arm_bL_ops->free_opp_table(cpu_dev);
 out:
 	dev_err(cpu_dev, "%s: Failed to get data for cluster: %d\n", __func__,
 			cluster);
diff --git a/drivers/cpufreq/arm_big_little.h b/drivers/cpufreq/arm_big_little.h
index 70f18fc12d4a..a211f7db9d32 100644
--- a/drivers/cpufreq/arm_big_little.h
+++ b/drivers/cpufreq/arm_big_little.h
@@ -25,13 +25,16 @@
 
 struct cpufreq_arm_bL_ops {
 	char name[CPUFREQ_NAME_LEN];
-	int (*get_transition_latency)(struct device *cpu_dev);
 
 	/*
 	 * This must set opp table for cpu_dev in a similar way as done by
 	 * of_init_opp_table().
 	 */
 	int (*init_opp_table)(struct device *cpu_dev);
+
+	/* Optional */
+	int (*get_transition_latency)(struct device *cpu_dev);
+	void (*free_opp_table)(struct device *cpu_dev);
 };
 
 int bL_cpufreq_register(struct cpufreq_arm_bL_ops *ops);
diff --git a/drivers/cpufreq/arm_big_little_dt.c b/drivers/cpufreq/arm_big_little_dt.c
index 4550f6976768..ef0b3f1324d5 100644
--- a/drivers/cpufreq/arm_big_little_dt.c
+++ b/drivers/cpufreq/arm_big_little_dt.c
@@ -82,6 +82,7 @@ static struct cpufreq_arm_bL_ops dt_bL_ops = {
 	.name	= "dt-bl",
 	.get_transition_latency = dt_get_transition_latency,
 	.init_opp_table = dt_init_opp_table,
+	.free_opp_table = of_free_opp_table,
 };
 
 static int generic_bL_probe(struct platform_device *pdev)
diff --git a/drivers/cpufreq/cpufreq-dt.c b/drivers/cpufreq/cpufreq-dt.c
index f657c571b18e..9bc2720628a4 100644
--- a/drivers/cpufreq/cpufreq-dt.c
+++ b/drivers/cpufreq/cpufreq-dt.c
@@ -58,6 +58,8 @@ static int set_target(struct cpufreq_policy *policy, unsigned int index)
 	old_freq = clk_get_rate(cpu_clk) / 1000;
 
 	if (!IS_ERR(cpu_reg)) {
+		unsigned long opp_freq;
+
 		rcu_read_lock();
 		opp = dev_pm_opp_find_freq_ceil(cpu_dev, &freq_Hz);
 		if (IS_ERR(opp)) {
@@ -67,13 +69,16 @@ static int set_target(struct cpufreq_policy *policy, unsigned int index)
 			return PTR_ERR(opp);
 		}
 		volt = dev_pm_opp_get_voltage(opp);
+		opp_freq = dev_pm_opp_get_freq(opp);
 		rcu_read_unlock();
 		tol = volt * priv->voltage_tolerance / 100;
 		volt_old = regulator_get_voltage(cpu_reg);
+		dev_dbg(cpu_dev, "Found OPP: %ld kHz, %ld uV\n",
+			opp_freq / 1000, volt);
 	}
 
 	dev_dbg(cpu_dev, "%u MHz, %ld mV --> %u MHz, %ld mV\n",
-		old_freq / 1000, volt_old ? volt_old / 1000 : -1,
+		old_freq / 1000, (volt_old > 0) ? volt_old / 1000 : -1,
 		new_freq / 1000, volt ? volt / 1000 : -1);
 
 	/* scaling up?  scale voltage before frequency */
@@ -89,7 +94,7 @@ static int set_target(struct cpufreq_policy *policy, unsigned int index)
 	ret = clk_set_rate(cpu_clk, freq_exact);
 	if (ret) {
 		dev_err(cpu_dev, "failed to set clock rate: %d\n", ret);
-		if (!IS_ERR(cpu_reg))
+		if (!IS_ERR(cpu_reg) && volt_old > 0)
 			regulator_set_voltage_tol(cpu_reg, volt_old, tol);
 		return ret;
 	}
@@ -181,7 +186,6 @@ static int cpufreq_init(struct cpufreq_policy *policy)
 {
 	struct cpufreq_dt_platform_data *pd;
 	struct cpufreq_frequency_table *freq_table;
-	struct thermal_cooling_device *cdev;
 	struct device_node *np;
 	struct private_data *priv;
 	struct device *cpu_dev;
@@ -210,7 +214,7 @@ static int cpufreq_init(struct cpufreq_policy *policy)
 	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
 	if (!priv) {
 		ret = -ENOMEM;
-		goto out_put_node;
+		goto out_free_opp;
 	}
 
 	of_property_read_u32(np, "voltage-tolerance", &priv->voltage_tolerance);
@@ -264,20 +268,6 @@ static int cpufreq_init(struct cpufreq_policy *policy)
 		goto out_free_priv;
 	}
 
-	/*
-	 * For now, just loading the cooling device;
-	 * thermal DT code takes care of matching them.
-	 */
-	if (of_find_property(np, "#cooling-cells", NULL)) {
-		cdev = of_cpufreq_cooling_register(np, cpu_present_mask);
-		if (IS_ERR(cdev))
-			dev_err(cpu_dev,
-				"running cpufreq without cooling device: %ld\n",
-				PTR_ERR(cdev));
-		else
-			priv->cdev = cdev;
-	}
-
 	priv->cpu_dev = cpu_dev;
 	priv->cpu_reg = cpu_reg;
 	policy->driver_data = priv;
@@ -287,7 +277,7 @@ static int cpufreq_init(struct cpufreq_policy *policy)
 	if (ret) {
 		dev_err(cpu_dev, "%s: invalid frequency table: %d\n", __func__,
 			ret);
-		goto out_cooling_unregister;
+		goto out_free_cpufreq_table;
 	}
 
 	policy->cpuinfo.transition_latency = transition_latency;
@@ -300,12 +290,12 @@ static int cpufreq_init(struct cpufreq_policy *policy)
 
 	return 0;
 
-out_cooling_unregister:
-	cpufreq_cooling_unregister(priv->cdev);
+out_free_cpufreq_table:
 	dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table);
 out_free_priv:
 	kfree(priv);
-out_put_node:
+out_free_opp:
+	of_free_opp_table(cpu_dev);
 	of_node_put(np);
 out_put_reg_clk:
 	clk_put(cpu_clk);
@@ -319,8 +309,10 @@ static int cpufreq_exit(struct cpufreq_policy *policy)
 {
 	struct private_data *priv = policy->driver_data;
 
-	cpufreq_cooling_unregister(priv->cdev);
+	if (priv->cdev)
+		cpufreq_cooling_unregister(priv->cdev);
 	dev_pm_opp_free_cpufreq_table(priv->cpu_dev, &policy->freq_table);
+	of_free_opp_table(priv->cpu_dev);
 	clk_put(policy->clk);
 	if (!IS_ERR(priv->cpu_reg))
 		regulator_put(priv->cpu_reg);
@@ -329,6 +321,33 @@ static int cpufreq_exit(struct cpufreq_policy *policy)
 	return 0;
 }
 
+static void cpufreq_ready(struct cpufreq_policy *policy)
+{
+	struct private_data *priv = policy->driver_data;
+	struct device_node *np = of_node_get(priv->cpu_dev->of_node);
+
+	if (WARN_ON(!np))
+		return;
+
+	/*
+	 * For now, just loading the cooling device;
+	 * thermal DT code takes care of matching them.
+	 */
+	if (of_find_property(np, "#cooling-cells", NULL)) {
+		priv->cdev = of_cpufreq_cooling_register(np,
+							 policy->related_cpus);
+		if (IS_ERR(priv->cdev)) {
+			dev_err(priv->cpu_dev,
+				"running cpufreq without cooling device: %ld\n",
+				PTR_ERR(priv->cdev));
+
+			priv->cdev = NULL;
+		}
+	}
+
+	of_node_put(np);
+}
+
 static struct cpufreq_driver dt_cpufreq_driver = {
 	.flags = CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
 	.verify = cpufreq_generic_frequency_table_verify,
@@ -336,6 +355,7 @@ static struct cpufreq_driver dt_cpufreq_driver = {
 	.get = cpufreq_generic_get,
 	.init = cpufreq_init,
 	.exit = cpufreq_exit,
+	.ready = cpufreq_ready,
 	.name = "cpufreq-dt",
 	.attr = cpufreq_generic_attr,
 };
diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c
index 4473eba1d6b0..a09a29c312a9 100644
--- a/drivers/cpufreq/cpufreq.c
+++ b/drivers/cpufreq/cpufreq.c
@@ -535,7 +535,7 @@ static int cpufreq_set_policy(struct cpufreq_policy *policy,
 static ssize_t store_##file_name					\
 (struct cpufreq_policy *policy, const char *buf, size_t count)		\
 {									\
-	int ret;							\
+	int ret, temp;							\
 	struct cpufreq_policy new_policy;				\
 									\
 	ret = cpufreq_get_policy(&new_policy, policy->cpu);		\
@@ -546,8 +546,10 @@ static ssize_t store_##file_name					\
 	if (ret != 1)							\
 		return -EINVAL;						\
 									\
+	temp = new_policy.object;					\
 	ret = cpufreq_set_policy(policy, &new_policy);		\
-	policy->user_policy.object = policy->object;			\
+	if (!ret)							\
+		policy->user_policy.object = temp;			\
 									\
 	return ret ? ret : count;					\
 }
@@ -898,46 +900,31 @@ static int cpufreq_add_dev_interface(struct cpufreq_policy *policy,
 	struct freq_attr **drv_attr;
 	int ret = 0;
 
-	/* prepare interface data */
-	ret = kobject_init_and_add(&policy->kobj, &ktype_cpufreq,
-				   &dev->kobj, "cpufreq");
-	if (ret)
-		return ret;
-
 	/* set up files for this cpu device */
 	drv_attr = cpufreq_driver->attr;
 	while ((drv_attr) && (*drv_attr)) {
 		ret = sysfs_create_file(&policy->kobj, &((*drv_attr)->attr));
 		if (ret)
-			goto err_out_kobj_put;
+			return ret;
 		drv_attr++;
 	}
 	if (cpufreq_driver->get) {
 		ret = sysfs_create_file(&policy->kobj, &cpuinfo_cur_freq.attr);
 		if (ret)
-			goto err_out_kobj_put;
+			return ret;
 	}
 
 	ret = sysfs_create_file(&policy->kobj, &scaling_cur_freq.attr);
 	if (ret)
-		goto err_out_kobj_put;
+		return ret;
 
 	if (cpufreq_driver->bios_limit) {
 		ret = sysfs_create_file(&policy->kobj, &bios_limit.attr);
 		if (ret)
-			goto err_out_kobj_put;
+			return ret;
 	}
 
-	ret = cpufreq_add_dev_symlink(policy);
-	if (ret)
-		goto err_out_kobj_put;
-
-	return ret;
-
-err_out_kobj_put:
-	kobject_put(&policy->kobj);
-	wait_for_completion(&policy->kobj_unregister);
-	return ret;
+	return cpufreq_add_dev_symlink(policy);
 }
 
 static void cpufreq_init_policy(struct cpufreq_policy *policy)
@@ -1196,6 +1183,8 @@ static int __cpufreq_add_dev(struct device *dev, struct subsys_interface *sif)
 		goto err_set_policy_cpu;
 	}
 
+	down_write(&policy->rwsem);
+
 	/* related cpus should atleast have policy->cpus */
 	cpumask_or(policy->related_cpus, policy->related_cpus, policy->cpus);
 
@@ -1208,9 +1197,17 @@ static int __cpufreq_add_dev(struct device *dev, struct subsys_interface *sif)
 	if (!recover_policy) {
 		policy->user_policy.min = policy->min;
 		policy->user_policy.max = policy->max;
+
+		/* prepare interface data */
+		ret = kobject_init_and_add(&policy->kobj, &ktype_cpufreq,
+					   &dev->kobj, "cpufreq");
+		if (ret) {
+			pr_err("%s: failed to init policy->kobj: %d\n",
+			       __func__, ret);
+			goto err_init_policy_kobj;
+		}
 	}
 
-	down_write(&policy->rwsem);
 	write_lock_irqsave(&cpufreq_driver_lock, flags);
 	for_each_cpu(j, policy->cpus)
 		per_cpu(cpufreq_cpu_data, j) = policy;
@@ -1288,8 +1285,13 @@ static int __cpufreq_add_dev(struct device *dev, struct subsys_interface *sif)
 	up_write(&policy->rwsem);
 
 	kobject_uevent(&policy->kobj, KOBJ_ADD);
+
 	up_read(&cpufreq_rwsem);
 
+	/* Callback for handling stuff after policy is ready */
+	if (cpufreq_driver->ready)
+		cpufreq_driver->ready(policy);
+
 	pr_debug("initialization complete\n");
 
 	return 0;
@@ -1301,6 +1303,11 @@ err_get_freq:
 		per_cpu(cpufreq_cpu_data, j) = NULL;
 	write_unlock_irqrestore(&cpufreq_driver_lock, flags);
 
+	if (!recover_policy) {
+		kobject_put(&policy->kobj);
+		wait_for_completion(&policy->kobj_unregister);
+	}
+err_init_policy_kobj:
 	up_write(&policy->rwsem);
 
 	if (cpufreq_driver->exit)
diff --git a/drivers/cpufreq/exynos5440-cpufreq.c b/drivers/cpufreq/exynos5440-cpufreq.c
index f33f25b483ca..27a57ed9eb2c 100644
--- a/drivers/cpufreq/exynos5440-cpufreq.c
+++ b/drivers/cpufreq/exynos5440-cpufreq.c
@@ -371,7 +371,7 @@ static int exynos_cpufreq_probe(struct platform_device *pdev)
 	if (ret) {
 		dev_err(dvfs_info->dev,
 			"failed to init cpufreq table: %d\n", ret);
-		goto err_put_node;
+		goto err_free_opp;
 	}
 	dvfs_info->freq_count = dev_pm_opp_get_opp_count(dvfs_info->dev);
 	exynos_sort_descend_freq_table();
@@ -423,6 +423,8 @@ static int exynos_cpufreq_probe(struct platform_device *pdev)
 
 err_free_table:
 	dev_pm_opp_free_cpufreq_table(dvfs_info->dev, &dvfs_info->freq_table);
+err_free_opp:
+	of_free_opp_table(dvfs_info->dev);
 err_put_node:
 	of_node_put(np);
 	dev_err(&pdev->dev, "%s: failed initialization\n", __func__);
@@ -433,6 +435,7 @@ static int exynos_cpufreq_remove(struct platform_device *pdev)
 {
 	cpufreq_unregister_driver(&exynos_driver);
 	dev_pm_opp_free_cpufreq_table(dvfs_info->dev, &dvfs_info->freq_table);
+	of_free_opp_table(dvfs_info->dev);
 	return 0;
 }
 
diff --git a/drivers/cpufreq/imx6q-cpufreq.c b/drivers/cpufreq/imx6q-cpufreq.c
index c2d30765bf3d..5da1d131f770 100644
--- a/drivers/cpufreq/imx6q-cpufreq.c
+++ b/drivers/cpufreq/imx6q-cpufreq.c
@@ -31,6 +31,7 @@ static struct clk *step_clk;
 static struct clk *pll2_pfd2_396m_clk;
 
 static struct device *cpu_dev;
+static bool free_opp;
 static struct cpufreq_frequency_table *freq_table;
 static unsigned int transition_latency;
 
@@ -207,11 +208,14 @@ static int imx6q_cpufreq_probe(struct platform_device *pdev)
 			goto put_reg;
 		}
 
+		/* Because we have added the OPPs here, we must free them */
+		free_opp = true;
+
 		num = dev_pm_opp_get_opp_count(cpu_dev);
 		if (num < 0) {
 			ret = num;
 			dev_err(cpu_dev, "no OPP table is found: %d\n", ret);
-			goto put_reg;
+			goto out_free_opp;
 		}
 	}
 
@@ -306,6 +310,9 @@ soc_opp_out:
 
 free_freq_table:
 	dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table);
+out_free_opp:
+	if (free_opp)
+		of_free_opp_table(cpu_dev);
 put_reg:
 	if (!IS_ERR(arm_reg))
 		regulator_put(arm_reg);
@@ -332,6 +339,8 @@ static int imx6q_cpufreq_remove(struct platform_device *pdev)
 {
 	cpufreq_unregister_driver(&imx6q_cpufreq_driver);
 	dev_pm_opp_free_cpufreq_table(cpu_dev, &freq_table);
+	if (free_opp)
+		of_free_opp_table(cpu_dev);
 	regulator_put(arm_reg);
 	if (!IS_ERR(pu_reg))
 		regulator_put(pu_reg);
diff --git a/drivers/cpufreq/intel_pstate.c b/drivers/cpufreq/intel_pstate.c
index 27bb6d3877ed..1405b393c93d 100644
--- a/drivers/cpufreq/intel_pstate.c
+++ b/drivers/cpufreq/intel_pstate.c
@@ -137,6 +137,7 @@ struct cpu_defaults {
 
 static struct pstate_adjust_policy pid_params;
 static struct pstate_funcs pstate_funcs;
+static int hwp_active;
 
 struct perf_limits {
 	int no_turbo;
@@ -244,6 +245,34 @@ static inline void update_turbo_state(void)
 		 cpu->pstate.max_pstate == cpu->pstate.turbo_pstate);
 }
 
+#define PCT_TO_HWP(x) (x * 255 / 100)
+static void intel_pstate_hwp_set(void)
+{
+	int min, max, cpu;
+	u64 value, freq;
+
+	get_online_cpus();
+
+	for_each_online_cpu(cpu) {
+		rdmsrl_on_cpu(cpu, MSR_HWP_REQUEST, &value);
+		min = PCT_TO_HWP(limits.min_perf_pct);
+		value &= ~HWP_MIN_PERF(~0L);
+		value |= HWP_MIN_PERF(min);
+
+		max = PCT_TO_HWP(limits.max_perf_pct);
+		if (limits.no_turbo) {
+			rdmsrl( MSR_HWP_CAPABILITIES, freq);
+			max = HWP_GUARANTEED_PERF(freq);
+		}
+
+		value &= ~HWP_MAX_PERF(~0L);
+		value |= HWP_MAX_PERF(max);
+		wrmsrl_on_cpu(cpu, MSR_HWP_REQUEST, value);
+	}
+
+	put_online_cpus();
+}
+
 /************************** debugfs begin ************************/
 static int pid_param_set(void *data, u64 val)
 {
@@ -279,6 +308,8 @@ static void __init intel_pstate_debug_expose_params(void)
 	struct dentry *debugfs_parent;
 	int i = 0;
 
+	if (hwp_active)
+		return;
 	debugfs_parent = debugfs_create_dir("pstate_snb", NULL);
 	if (IS_ERR_OR_NULL(debugfs_parent))
 		return;
@@ -329,8 +360,12 @@ static ssize_t store_no_turbo(struct kobject *a, struct attribute *b,
 		pr_warn("Turbo disabled by BIOS or unavailable on processor\n");
 		return -EPERM;
 	}
+
 	limits.no_turbo = clamp_t(int, input, 0, 1);
 
+	if (hwp_active)
+		intel_pstate_hwp_set();
+
 	return count;
 }
 
@@ -348,6 +383,8 @@ static ssize_t store_max_perf_pct(struct kobject *a, struct attribute *b,
 	limits.max_perf_pct = min(limits.max_policy_pct, limits.max_sysfs_pct);
 	limits.max_perf = div_fp(int_tofp(limits.max_perf_pct), int_tofp(100));
 
+	if (hwp_active)
+		intel_pstate_hwp_set();
 	return count;
 }
 
@@ -363,6 +400,8 @@ static ssize_t store_min_perf_pct(struct kobject *a, struct attribute *b,
 	limits.min_perf_pct = clamp_t(int, input, 0 , 100);
 	limits.min_perf = div_fp(int_tofp(limits.min_perf_pct), int_tofp(100));
 
+	if (hwp_active)
+		intel_pstate_hwp_set();
 	return count;
 }
 
@@ -395,8 +434,16 @@ static void __init intel_pstate_sysfs_expose_params(void)
 	rc = sysfs_create_group(intel_pstate_kobject, &intel_pstate_attr_group);
 	BUG_ON(rc);
 }
-
 /************************** sysfs end ************************/
+
+static void intel_pstate_hwp_enable(void)
+{
+	hwp_active++;
+	pr_info("intel_pstate HWP enabled\n");
+
+	wrmsrl( MSR_PM_ENABLE, 0x1);
+}
+
 static int byt_get_min_pstate(void)
 {
 	u64 value;
@@ -648,6 +695,14 @@ static inline void intel_pstate_sample(struct cpudata *cpu)
 	cpu->prev_mperf = mperf;
 }
 
+static inline void intel_hwp_set_sample_time(struct cpudata *cpu)
+{
+	int delay;
+
+	delay = msecs_to_jiffies(50);
+	mod_timer_pinned(&cpu->timer, jiffies + delay);
+}
+
 static inline void intel_pstate_set_sample_time(struct cpudata *cpu)
 {
 	int delay;
@@ -694,6 +749,14 @@ static inline void intel_pstate_adjust_busy_pstate(struct cpudata *cpu)
 	intel_pstate_set_pstate(cpu, cpu->pstate.current_pstate - ctl);
 }
 
+static void intel_hwp_timer_func(unsigned long __data)
+{
+	struct cpudata *cpu = (struct cpudata *) __data;
+
+	intel_pstate_sample(cpu);
+	intel_hwp_set_sample_time(cpu);
+}
+
 static void intel_pstate_timer_func(unsigned long __data)
 {
 	struct cpudata *cpu = (struct cpudata *) __data;
@@ -730,6 +793,7 @@ static const struct x86_cpu_id intel_pstate_cpu_ids[] = {
 	ICPU(0x3f, core_params),
 	ICPU(0x45, core_params),
 	ICPU(0x46, core_params),
+	ICPU(0x47, core_params),
 	ICPU(0x4c, byt_params),
 	ICPU(0x4f, core_params),
 	ICPU(0x56, core_params),
@@ -737,6 +801,11 @@ static const struct x86_cpu_id intel_pstate_cpu_ids[] = {
 };
 MODULE_DEVICE_TABLE(x86cpu, intel_pstate_cpu_ids);
 
+static const struct x86_cpu_id intel_pstate_cpu_oob_ids[] = {
+	ICPU(0x56, core_params),
+	{}
+};
+
 static int intel_pstate_init_cpu(unsigned int cpunum)
 {
 	struct cpudata *cpu;
@@ -753,9 +822,14 @@ static int intel_pstate_init_cpu(unsigned int cpunum)
 	intel_pstate_get_cpu_pstates(cpu);
 
 	init_timer_deferrable(&cpu->timer);
-	cpu->timer.function = intel_pstate_timer_func;
 	cpu->timer.data = (unsigned long)cpu;
 	cpu->timer.expires = jiffies + HZ/100;
+
+	if (!hwp_active)
+		cpu->timer.function = intel_pstate_timer_func;
+	else
+		cpu->timer.function = intel_hwp_timer_func;
+
 	intel_pstate_busy_pid_reset(cpu);
 	intel_pstate_sample(cpu);
 
@@ -792,6 +866,7 @@ static int intel_pstate_set_policy(struct cpufreq_policy *policy)
 		limits.no_turbo = 0;
 		return 0;
 	}
+
 	limits.min_perf_pct = (policy->min * 100) / policy->cpuinfo.max_freq;
 	limits.min_perf_pct = clamp_t(int, limits.min_perf_pct, 0 , 100);
 	limits.min_perf = div_fp(int_tofp(limits.min_perf_pct), int_tofp(100));
@@ -801,6 +876,9 @@ static int intel_pstate_set_policy(struct cpufreq_policy *policy)
 	limits.max_perf_pct = min(limits.max_policy_pct, limits.max_sysfs_pct);
 	limits.max_perf = div_fp(int_tofp(limits.max_perf_pct), int_tofp(100));
 
+	if (hwp_active)
+		intel_pstate_hwp_set();
+
 	return 0;
 }
 
@@ -823,6 +901,9 @@ static void intel_pstate_stop_cpu(struct cpufreq_policy *policy)
 	pr_info("intel_pstate CPU %d exiting\n", cpu_num);
 
 	del_timer_sync(&all_cpu_data[cpu_num]->timer);
+	if (hwp_active)
+		return;
+
 	intel_pstate_set_pstate(cpu, cpu->pstate.min_pstate);
 }
 
@@ -866,6 +947,7 @@ static struct cpufreq_driver intel_pstate_driver = {
 };
 
 static int __initdata no_load;
+static int __initdata no_hwp;
 
 static int intel_pstate_msrs_not_valid(void)
 {
@@ -943,15 +1025,46 @@ static bool intel_pstate_no_acpi_pss(void)
 	return true;
 }
 
+static bool intel_pstate_has_acpi_ppc(void)
+{
+	int i;
+
+	for_each_possible_cpu(i) {
+		struct acpi_processor *pr = per_cpu(processors, i);
+
+		if (!pr)
+			continue;
+		if (acpi_has_method(pr->handle, "_PPC"))
+			return true;
+	}
+	return false;
+}
+
+enum {
+	PSS,
+	PPC,
+};
+
 struct hw_vendor_info {
 	u16  valid;
 	char oem_id[ACPI_OEM_ID_SIZE];
 	char oem_table_id[ACPI_OEM_TABLE_ID_SIZE];
+	int  oem_pwr_table;
 };
 
 /* Hardware vendor-specific info that has its own power management modes */
 static struct hw_vendor_info vendor_info[] = {
-	{1, "HP    ", "ProLiant"},
+	{1, "HP    ", "ProLiant", PSS},
+	{1, "ORACLE", "X4-2    ", PPC},
+	{1, "ORACLE", "X4-2L   ", PPC},
+	{1, "ORACLE", "X4-2B   ", PPC},
+	{1, "ORACLE", "X3-2    ", PPC},
+	{1, "ORACLE", "X3-2L   ", PPC},
+	{1, "ORACLE", "X3-2B   ", PPC},
+	{1, "ORACLE", "X4470M2 ", PPC},
+	{1, "ORACLE", "X4270M3 ", PPC},
+	{1, "ORACLE", "X4270M2 ", PPC},
+	{1, "ORACLE", "X4170M2 ", PPC},
 	{0, "", ""},
 };
 
@@ -959,6 +1072,15 @@ static bool intel_pstate_platform_pwr_mgmt_exists(void)
 {
 	struct acpi_table_header hdr;
 	struct hw_vendor_info *v_info;
+	const struct x86_cpu_id *id;
+	u64 misc_pwr;
+
+	id = x86_match_cpu(intel_pstate_cpu_oob_ids);
+	if (id) {
+		rdmsrl(MSR_MISC_PWR_MGMT, misc_pwr);
+		if ( misc_pwr & (1 << 8))
+			return true;
+	}
 
 	if (acpi_disabled ||
 	    ACPI_FAILURE(acpi_get_table_header(ACPI_SIG_FADT, 0, &hdr)))
@@ -966,15 +1088,21 @@ static bool intel_pstate_platform_pwr_mgmt_exists(void)
 
 	for (v_info = vendor_info; v_info->valid; v_info++) {
 		if (!strncmp(hdr.oem_id, v_info->oem_id, ACPI_OEM_ID_SIZE) &&
-		    !strncmp(hdr.oem_table_id, v_info->oem_table_id, ACPI_OEM_TABLE_ID_SIZE) &&
-		    intel_pstate_no_acpi_pss())
-			return true;
+			!strncmp(hdr.oem_table_id, v_info->oem_table_id,
+						ACPI_OEM_TABLE_ID_SIZE))
+			switch (v_info->oem_pwr_table) {
+			case PSS:
+				return intel_pstate_no_acpi_pss();
+			case PPC:
+				return intel_pstate_has_acpi_ppc();
+			}
 	}
 
 	return false;
 }
 #else /* CONFIG_ACPI not enabled */
 static inline bool intel_pstate_platform_pwr_mgmt_exists(void) { return false; }
+static inline bool intel_pstate_has_acpi_ppc(void) { return false; }
 #endif /* CONFIG_ACPI */
 
 static int __init intel_pstate_init(void)
@@ -982,6 +1110,7 @@ static int __init intel_pstate_init(void)
 	int cpu, rc = 0;
 	const struct x86_cpu_id *id;
 	struct cpu_defaults *cpu_info;
+	struct cpuinfo_x86 *c = &boot_cpu_data;
 
 	if (no_load)
 		return -ENODEV;
@@ -1011,6 +1140,9 @@ static int __init intel_pstate_init(void)
 	if (!all_cpu_data)
 		return -ENOMEM;
 
+	if (cpu_has(c,X86_FEATURE_HWP) && !no_hwp)
+		intel_pstate_hwp_enable();
+
 	rc = cpufreq_register_driver(&intel_pstate_driver);
 	if (rc)
 		goto out;
@@ -1041,6 +1173,8 @@ static int __init intel_pstate_setup(char *str)
 
 	if (!strcmp(str, "disable"))
 		no_load = 1;
+	if (!strcmp(str, "no_hwp"))
+		no_hwp = 1;
 	return 0;
 }
 early_param("intel_pstate", intel_pstate_setup);
diff --git a/drivers/cpufreq/ls1x-cpufreq.c b/drivers/cpufreq/ls1x-cpufreq.c
new file mode 100644
index 000000000000..25fbd6a1374f
--- /dev/null
+++ b/drivers/cpufreq/ls1x-cpufreq.c
@@ -0,0 +1,223 @@
+/*
+ * CPU Frequency Scaling for Loongson 1 SoC
+ *
+ * Copyright (C) 2014 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/cpu.h>
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <asm/mach-loongson1/cpufreq.h>
+#include <asm/mach-loongson1/loongson1.h>
+
+static struct {
+	struct device *dev;
+	struct clk *clk;	/* CPU clk */
+	struct clk *mux_clk;	/* MUX of CPU clk */
+	struct clk *pll_clk;	/* PLL clk */
+	struct clk *osc_clk;	/* OSC clk */
+	unsigned int max_freq;
+	unsigned int min_freq;
+} ls1x_cpufreq;
+
+static int ls1x_cpufreq_notifier(struct notifier_block *nb,
+				 unsigned long val, void *data)
+{
+	if (val == CPUFREQ_POSTCHANGE)
+		current_cpu_data.udelay_val = loops_per_jiffy;
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block ls1x_cpufreq_notifier_block = {
+	.notifier_call = ls1x_cpufreq_notifier
+};
+
+static int ls1x_cpufreq_target(struct cpufreq_policy *policy,
+			       unsigned int index)
+{
+	unsigned int old_freq, new_freq;
+
+	old_freq = policy->cur;
+	new_freq = policy->freq_table[index].frequency;
+
+	/*
+	 * The procedure of reconfiguring CPU clk is as below.
+	 *
+	 *  - Reparent CPU clk to OSC clk
+	 *  - Reset CPU clock (very important)
+	 *  - Reconfigure CPU DIV
+	 *  - Reparent CPU clk back to CPU DIV clk
+	 */
+
+	dev_dbg(ls1x_cpufreq.dev, "%u KHz --> %u KHz\n", old_freq, new_freq);
+	clk_set_parent(policy->clk, ls1x_cpufreq.osc_clk);
+	__raw_writel(__raw_readl(LS1X_CLK_PLL_DIV) | RST_CPU_EN | RST_CPU,
+		     LS1X_CLK_PLL_DIV);
+	__raw_writel(__raw_readl(LS1X_CLK_PLL_DIV) & ~(RST_CPU_EN | RST_CPU),
+		     LS1X_CLK_PLL_DIV);
+	clk_set_rate(ls1x_cpufreq.mux_clk, new_freq * 1000);
+	clk_set_parent(policy->clk, ls1x_cpufreq.mux_clk);
+
+	return 0;
+}
+
+static int ls1x_cpufreq_init(struct cpufreq_policy *policy)
+{
+	struct cpufreq_frequency_table *freq_tbl;
+	unsigned int pll_freq, freq;
+	int steps, i, ret;
+
+	pll_freq = clk_get_rate(ls1x_cpufreq.pll_clk) / 1000;
+
+	steps = 1 << DIV_CPU_WIDTH;
+	freq_tbl = kzalloc(sizeof(*freq_tbl) * steps, GFP_KERNEL);
+	if (!freq_tbl) {
+		dev_err(ls1x_cpufreq.dev,
+			"failed to alloc cpufreq_frequency_table\n");
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	for (i = 0; i < (steps - 1); i++) {
+		freq = pll_freq / (i + 1);
+		if ((freq < ls1x_cpufreq.min_freq) ||
+		    (freq > ls1x_cpufreq.max_freq))
+			freq_tbl[i].frequency = CPUFREQ_ENTRY_INVALID;
+		else
+			freq_tbl[i].frequency = freq;
+		dev_dbg(ls1x_cpufreq.dev,
+			"cpufreq table: index %d: frequency %d\n", i,
+			freq_tbl[i].frequency);
+	}
+	freq_tbl[i].frequency = CPUFREQ_TABLE_END;
+
+	policy->clk = ls1x_cpufreq.clk;
+	ret = cpufreq_generic_init(policy, freq_tbl, 0);
+	if (ret)
+		kfree(freq_tbl);
+out:
+	return ret;
+}
+
+static int ls1x_cpufreq_exit(struct cpufreq_policy *policy)
+{
+	kfree(policy->freq_table);
+	return 0;
+}
+
+static struct cpufreq_driver ls1x_cpufreq_driver = {
+	.name		= "cpufreq-ls1x",
+	.flags		= CPUFREQ_STICKY | CPUFREQ_NEED_INITIAL_FREQ_CHECK,
+	.verify		= cpufreq_generic_frequency_table_verify,
+	.target_index	= ls1x_cpufreq_target,
+	.get		= cpufreq_generic_get,
+	.init		= ls1x_cpufreq_init,
+	.exit		= ls1x_cpufreq_exit,
+	.attr		= cpufreq_generic_attr,
+};
+
+static int ls1x_cpufreq_remove(struct platform_device *pdev)
+{
+	cpufreq_unregister_notifier(&ls1x_cpufreq_notifier_block,
+				    CPUFREQ_TRANSITION_NOTIFIER);
+	cpufreq_unregister_driver(&ls1x_cpufreq_driver);
+
+	return 0;
+}
+
+static int ls1x_cpufreq_probe(struct platform_device *pdev)
+{
+	struct plat_ls1x_cpufreq *pdata = pdev->dev.platform_data;
+	struct clk *clk;
+	int ret;
+
+	if (!pdata || !pdata->clk_name || !pdata->osc_clk_name)
+		return -EINVAL;
+
+	ls1x_cpufreq.dev = &pdev->dev;
+
+	clk = devm_clk_get(&pdev->dev, pdata->clk_name);
+	if (IS_ERR(clk)) {
+		dev_err(ls1x_cpufreq.dev, "unable to get %s clock\n",
+			pdata->clk_name);
+		ret = PTR_ERR(clk);
+		goto out;
+	}
+	ls1x_cpufreq.clk = clk;
+
+	clk = clk_get_parent(clk);
+	if (IS_ERR(clk)) {
+		dev_err(ls1x_cpufreq.dev, "unable to get parent of %s clock\n",
+			__clk_get_name(ls1x_cpufreq.clk));
+		ret = PTR_ERR(clk);
+		goto out;
+	}
+	ls1x_cpufreq.mux_clk = clk;
+
+	clk = clk_get_parent(clk);
+	if (IS_ERR(clk)) {
+		dev_err(ls1x_cpufreq.dev, "unable to get parent of %s clock\n",
+			__clk_get_name(ls1x_cpufreq.mux_clk));
+		ret = PTR_ERR(clk);
+		goto out;
+	}
+	ls1x_cpufreq.pll_clk = clk;
+
+	clk = devm_clk_get(&pdev->dev, pdata->osc_clk_name);
+	if (IS_ERR(clk)) {
+		dev_err(ls1x_cpufreq.dev, "unable to get %s clock\n",
+			pdata->osc_clk_name);
+		ret = PTR_ERR(clk);
+		goto out;
+	}
+	ls1x_cpufreq.osc_clk = clk;
+
+	ls1x_cpufreq.max_freq = pdata->max_freq;
+	ls1x_cpufreq.min_freq = pdata->min_freq;
+
+	ret = cpufreq_register_driver(&ls1x_cpufreq_driver);
+	if (ret) {
+		dev_err(ls1x_cpufreq.dev,
+			"failed to register cpufreq driver: %d\n", ret);
+		goto out;
+	}
+
+	ret = cpufreq_register_notifier(&ls1x_cpufreq_notifier_block,
+					CPUFREQ_TRANSITION_NOTIFIER);
+
+	if (!ret)
+		goto out;
+
+	dev_err(ls1x_cpufreq.dev, "failed to register cpufreq notifier: %d\n",
+		ret);
+
+	cpufreq_unregister_driver(&ls1x_cpufreq_driver);
+out:
+	return ret;
+}
+
+static struct platform_driver ls1x_cpufreq_platdrv = {
+	.driver = {
+		.name	= "ls1x-cpufreq",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= ls1x_cpufreq_probe,
+	.remove		= ls1x_cpufreq_remove,
+};
+
+module_platform_driver(ls1x_cpufreq_platdrv);
+
+MODULE_AUTHOR("Kelvin Cheung <keguang.zhang@gmail.com>");
+MODULE_DESCRIPTION("Loongson 1 CPUFreq driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/cpufreq/pcc-cpufreq.c b/drivers/cpufreq/pcc-cpufreq.c
index 4d2c8e861089..2a0d58959acf 100644
--- a/drivers/cpufreq/pcc-cpufreq.c
+++ b/drivers/cpufreq/pcc-cpufreq.c
@@ -603,6 +603,13 @@ static void __exit pcc_cpufreq_exit(void)
 	free_percpu(pcc_cpu_info);
 }
 
+static const struct acpi_device_id processor_device_ids[] = {
+	{ACPI_PROCESSOR_OBJECT_HID, },
+	{ACPI_PROCESSOR_DEVICE_HID, },
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, processor_device_ids);
+
 MODULE_AUTHOR("Matthew Garrett, Naga Chumbalkar");
 MODULE_VERSION(PCC_VERSION);
 MODULE_DESCRIPTION("Processor Clocking Control interface driver");