Merge commit 'origin/master'

Manual merge of:

	arch/powerpc/Kconfig
	arch/powerpc/kernel/stacktrace.c
	arch/powerpc/mm/slice.c
	arch/ppc/kernel/smp.c

1 files changed, 0 insertions, 185 deletions

diff --git a/drivers/i2c/busses/i2c-savage4.c b/drivers/i2c/busses/i2c-savage4.c
deleted file mode 100644
index 8adf4abaa035..000000000000
--- a/drivers/i2c/busses/i2c-savage4.c
+++ /dev/null
@@ -1,185 +0,0 @@
-/*
-    i2c-savage4.c - Part of lm_sensors, Linux kernel modules for hardware
-              monitoring
-    Copyright (C) 1998-2003  The LM Sensors Team
-    Alexander Wold <awold@bigfoot.com>
-    Mark D. Studebaker <mdsxyz123@yahoo.com>
-    
-    Based on i2c-voodoo3.c.
-
-    This program is free software; you can redistribute it and/or modify
-    it under the terms of the GNU General Public License as published by
-    the Free Software Foundation; either version 2 of the License, or
-    (at your option) any later version.
-
-    This program is distributed in the hope that it will be useful,
-    but WITHOUT ANY WARRANTY; without even the implied warranty of
-    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-    GNU General Public License for more details.
-
-    You should have received a copy of the GNU General Public License
-    along with this program; if not, write to the Free Software
-    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-*/
-
-/* This interfaces to the I2C bus of the Savage4 to gain access to
-   the BT869 and possibly other I2C devices. The DDC bus is not
-   yet supported because its register is not memory-mapped.
-*/
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/pci.h>
-#include <linux/i2c.h>
-#include <linux/i2c-algo-bit.h>
-#include <asm/io.h>
-
-/* device IDs */
-#define PCI_CHIP_SAVAGE4	0x8A22
-#define PCI_CHIP_SAVAGE2000	0x9102
-
-#define REG			0xff20	/* Serial Port 1 Register */
-
-/* bit locations in the register */
-#define I2C_ENAB		0x00000020
-#define I2C_SCL_OUT		0x00000001
-#define I2C_SDA_OUT		0x00000002
-#define I2C_SCL_IN		0x00000008
-#define I2C_SDA_IN		0x00000010
-
-/* delays */
-#define CYCLE_DELAY		10
-#define TIMEOUT			(HZ / 2)
-
-
-static void __iomem *ioaddr;
-
-/* The sav GPIO registers don't have individual masks for each bit
-   so we always have to read before writing. */
-
-static void bit_savi2c_setscl(void *data, int val)
-{
-	unsigned int r;
-	r = readl(ioaddr + REG);
-	if(val)
-		r |= I2C_SCL_OUT;
-	else
-		r &= ~I2C_SCL_OUT;
-	writel(r, ioaddr + REG);
-	readl(ioaddr + REG);	/* flush posted write */
-}
-
-static void bit_savi2c_setsda(void *data, int val)
-{
-	unsigned int r;
-	r = readl(ioaddr + REG);
-	if(val)
-		r |= I2C_SDA_OUT;
-	else
-		r &= ~I2C_SDA_OUT;
-	writel(r, ioaddr + REG);
-	readl(ioaddr + REG);	/* flush posted write */
-}
-
-/* The GPIO pins are open drain, so the pins always remain outputs.
-   We rely on the i2c-algo-bit routines to set the pins high before
-   reading the input from other chips. */
-
-static int bit_savi2c_getscl(void *data)
-{
-	return (0 != (readl(ioaddr + REG) & I2C_SCL_IN));
-}
-
-static int bit_savi2c_getsda(void *data)
-{
-	return (0 != (readl(ioaddr + REG) & I2C_SDA_IN));
-}
-
-/* Configures the chip */
-
-static int config_s4(struct pci_dev *dev)
-{
-	unsigned long cadr;
-
-	/* map memory */
-	cadr = dev->resource[0].start;
-	cadr &= PCI_BASE_ADDRESS_MEM_MASK;
-	ioaddr = ioremap_nocache(cadr, 0x0080000);
-	if (ioaddr) {
-		/* writel(0x8160, ioaddr + REG2); */
-		writel(0x00000020, ioaddr + REG);
-		dev_info(&dev->dev, "Using Savage4 at %p\n", ioaddr);
-		return 0;
-	}
-	return -ENODEV;
-}
-
-static struct i2c_algo_bit_data sav_i2c_bit_data = {
-	.setsda		= bit_savi2c_setsda,
-	.setscl		= bit_savi2c_setscl,
-	.getsda		= bit_savi2c_getsda,
-	.getscl		= bit_savi2c_getscl,
-	.udelay		= CYCLE_DELAY,
-	.timeout	= TIMEOUT
-};
-
-static struct i2c_adapter savage4_i2c_adapter = {
-	.owner		= THIS_MODULE,
-	.id		= I2C_HW_B_SAVAGE,
-	.name		= "I2C Savage4 adapter",
-	.algo_data	= &sav_i2c_bit_data,
-};
-
-static struct pci_device_id savage4_ids[] __devinitdata = {
-	{ PCI_DEVICE(PCI_VENDOR_ID_S3, PCI_CHIP_SAVAGE4) },
-	{ PCI_DEVICE(PCI_VENDOR_ID_S3, PCI_CHIP_SAVAGE2000) },
-	{ 0, }
-};
-
-MODULE_DEVICE_TABLE (pci, savage4_ids);
-
-static int __devinit savage4_probe(struct pci_dev *dev, const struct pci_device_id *id)
-{
-	int retval;
-
-	retval = config_s4(dev);
-	if (retval)
-		return retval;
-
-	/* set up the sysfs linkage to our parent device */
-	savage4_i2c_adapter.dev.parent = &dev->dev;
-
-	return i2c_bit_add_bus(&savage4_i2c_adapter);
-}
-
-static void __devexit savage4_remove(struct pci_dev *dev)
-{
-	i2c_del_adapter(&savage4_i2c_adapter);
-	iounmap(ioaddr);
-}
-
-static struct pci_driver savage4_driver = {
-	.name		= "savage4_smbus",
-	.id_table	= savage4_ids,
-	.probe		= savage4_probe,
-	.remove		= __devexit_p(savage4_remove),
-};
-
-static int __init i2c_savage4_init(void)
-{
-	return pci_register_driver(&savage4_driver);
-}
-
-static void __exit i2c_savage4_exit(void)
-{
-	pci_unregister_driver(&savage4_driver);
-}
-
-MODULE_AUTHOR("Alexander Wold <awold@bigfoot.com> "
-		"and Mark D. Studebaker <mdsxyz123@yahoo.com>");
-MODULE_DESCRIPTION("Savage4 I2C/SMBus driver");
-MODULE_LICENSE("GPL");
-
-module_init(i2c_savage4_init);
-module_exit(i2c_savage4_exit);