ide: use PIO/MMIO operations directly where possible (v2)

This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.

v2:
* updated for scc_pata

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 13 insertions, 13 deletions

diff --git a/drivers/ide/pci/tc86c001.c b/drivers/ide/pci/tc86c001.c
index 4e893808f063..b408508a96ee 100644
--- a/drivers/ide/pci/tc86c001.c
+++ b/drivers/ide/pci/tc86c001.c
@@ -45,7 +45,7 @@ static int tc86c001_tune_chipset(ide_drive_t *drive, u8 speed)
 
 	scr &= (speed < XFER_MW_DMA_0) ? 0xf8ff : 0xff0f;
 	scr |= mode;
-	hwif->OUTW(scr, scr_port);
+	outw(scr, scr_port);
 
 	return ide_config_drive_speed(drive, speed);
 }
@@ -89,15 +89,15 @@ static int tc86c001_timer_expiry(ide_drive_t *drive)
 		       "attempting recovery...\n", drive->name);
 
 		/* Stop DMA */
-		hwif->OUTB(dma_cmd & ~0x01, hwif->dma_command);
+		outb(dma_cmd & ~0x01, hwif->dma_command);
 
 		/* Setup the dummy DMA transfer */
-		hwif->OUTW(0, sc_base + 0x0a);	/* Sector Count */
-		hwif->OUTW(0, twcr_port);	/* Transfer Word Count 1 or 2 */
+		outw(0, sc_base + 0x0a);	/* Sector Count */
+		outw(0, twcr_port);	/* Transfer Word Count 1 or 2 */
 
 		/* Start the dummy DMA transfer */
-		hwif->OUTB(0x00, hwif->dma_command); /* clear R_OR_WCTR for write */
-		hwif->OUTB(0x01, hwif->dma_command); /* set START_STOPBM */
+		outb(0x00, hwif->dma_command); /* clear R_OR_WCTR for write */
+		outb(0x01, hwif->dma_command); /* set START_STOPBM */
 
 		/*
 		 * If an interrupt was pending, it should come thru shortly.
@@ -128,8 +128,8 @@ static void tc86c001_dma_start(ide_drive_t *drive)
 	 * the appropriate system control registers for DMA to work
 	 * with LBA48 and ATAPI devices...
 	 */
-	hwif->OUTW(nsectors, sc_base + 0x0a);	/* Sector Count */
-	hwif->OUTW(SECTOR_SIZE / 2, twcr_port); /* Transfer Word Count 1/2 */
+	outw(nsectors, sc_base + 0x0a);	/* Sector Count */
+	outw(SECTOR_SIZE / 2, twcr_port); /* Transfer Word Count 1/2 */
 
 	/* Install our timeout expiry hook, saving the current handler... */
 	ide_set_hwifdata(hwif, hwgroup->expiry);
@@ -168,7 +168,7 @@ static int tc86c001_busproc(ide_drive_t *drive, int state)
 	}
 
 	/* System Control 1 Register bit 11 (ATA Hard Reset) write */
-	hwif->OUTW(scr1, sc_base + 0x00);
+	outw(scr1, sc_base + 0x00);
 	return 0;
 }
 
@@ -204,13 +204,13 @@ static void __devinit init_hwif_tc86c001(ide_hwif_t *hwif)
 	u16 scr1		= hwif->INW(sc_base + 0x00);;
 
 	/* System Control 1 Register bit 15 (Soft Reset) set */
-	hwif->OUTW(scr1 |  0x8000, sc_base + 0x00);
+	outw(scr1 |  0x8000, sc_base + 0x00);
 
 	/* System Control 1 Register bit 14 (FIFO Reset) set */
-	hwif->OUTW(scr1 |  0x4000, sc_base + 0x00);
+	outw(scr1 |  0x4000, sc_base + 0x00);
 
 	/* System Control 1 Register: reset clear */
-	hwif->OUTW(scr1 & ~0xc000, sc_base + 0x00);
+	outw(scr1 & ~0xc000, sc_base + 0x00);
 
 	/* Store the system control register base for convenience... */
 	hwif->config_data = sc_base;
@@ -228,7 +228,7 @@ static void __devinit init_hwif_tc86c001(ide_hwif_t *hwif)
 	 * Sector Count Control Register bits 0 and 1 set:
 	 * software sets Sector Count Register for master and slave device
 	 */
-	hwif->OUTW(0x0003, sc_base + 0x0c);
+	outw(0x0003, sc_base + 0x0c);
 
 	/* Sector Count Register limit */
 	hwif->rqsize	 = 0xffff;