ieee1394: move init_ohci1394_dma to drivers/firewire/

because drivers/ieee1394/ will be deleted.

Additional changes:
  - add some #include directives
  - adjust to use firewire/ohci.h instead of ieee1394/ohci1394.h,
    replace struct ti_ohci by a minimal struct ohci,
    replace quadlet_t from ieee1394_types.h by u32
  - two or three trivial stylistic changes
  - __iomem annotation

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

2 files changed, 0 insertions, 287 deletions

diff --git a/drivers/ieee1394/Makefile b/drivers/ieee1394/Makefile
index 1f8153b57503..427b86b87760 100644
--- a/drivers/ieee1394/Makefile
+++ b/drivers/ieee1394/Makefile
@@ -14,5 +14,3 @@ obj-$(CONFIG_IEEE1394_RAWIO) += raw1394.o
 obj-$(CONFIG_IEEE1394_SBP2) += sbp2.o
 obj-$(CONFIG_IEEE1394_DV1394) += dv1394.o
 obj-$(CONFIG_IEEE1394_ETH1394) += eth1394.o
-
-obj-$(CONFIG_PROVIDE_OHCI1394_DMA_INIT) += init_ohci1394_dma.o
diff --git a/drivers/ieee1394/init_ohci1394_dma.c b/drivers/ieee1394/init_ohci1394_dma.c
deleted file mode 100644
index ddaab6eb8ace..000000000000
--- a/drivers/ieee1394/init_ohci1394_dma.c
+++ /dev/null
@@ -1,285 +0,0 @@
-/*
- * init_ohci1394_dma.c - Initializes physical DMA on all OHCI 1394 controllers
- *
- * Copyright (C) 2006-2007      Bernhard Kaindl <bk@suse.de>
- *
- * Derived from drivers/ieee1394/ohci1394.c and arch/x86/kernel/early-quirks.c
- * this file has functions to:
- * - scan the PCI very early on boot for all OHCI 1394-compliant controllers
- * - reset and initialize them and make them join the IEEE1394 bus and
- * - enable physical DMA on them to allow remote debugging
- *
- * All code and data is marked as __init and __initdata, respective as
- * during boot, all OHCI1394 controllers may be claimed by the firewire
- * stack and at this point, this code should not touch them anymore.
- *
- * To use physical DMA after the initialization of the firewire stack,
- * be sure that the stack enables it and (re-)attach after the bus reset
- * which may be caused by the firewire stack initialization.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software Foundation,
- * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- */
-
-#include <linux/interrupt.h>	/* for ohci1394.h */
-#include <linux/delay.h>
-#include <linux/pci.h>		/* for PCI defines */
-#include <linux/init_ohci1394_dma.h>
-#include <asm/pci-direct.h>	/* for direct PCI config space access */
-#include <asm/fixmap.h>
-
-#include "ieee1394_types.h"
-#include "ohci1394.h"
-
-int __initdata init_ohci1394_dma_early;
-
-/* Reads a PHY register of an OHCI-1394 controller */
-static inline u8 __init get_phy_reg(struct ti_ohci *ohci, u8 addr)
-{
-	int i;
-	quadlet_t r;
-
-	reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | 0x00008000);
-
-	for (i = 0; i < OHCI_LOOP_COUNT; i++) {
-		if (reg_read(ohci, OHCI1394_PhyControl) & 0x80000000)
-			break;
-		mdelay(1);
-	}
-	r = reg_read(ohci, OHCI1394_PhyControl);
-
-	return (r & 0x00ff0000) >> 16;
-}
-
-/* Writes to a PHY register of an OHCI-1394 controller */
-static inline void __init set_phy_reg(struct ti_ohci *ohci, u8 addr, u8 data)
-{
-	int i;
-
-	reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | data | 0x00004000);
-
-	for (i = 0; i < OHCI_LOOP_COUNT; i++) {
-		u32 r = reg_read(ohci, OHCI1394_PhyControl);
-		if (!(r & 0x00004000))
-			break;
-		mdelay(1);
-	}
-}
-
-/* Resets an OHCI-1394 controller (for sane state before initialization) */
-static inline void __init init_ohci1394_soft_reset(struct ti_ohci *ohci) {
-	int i;
-
-	reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_softReset);
-
-	for (i = 0; i < OHCI_LOOP_COUNT; i++) {
-		if (!(reg_read(ohci, OHCI1394_HCControlSet)
-				   & OHCI1394_HCControl_softReset))
-			break;
-		mdelay(1);
-	}
-}
-
-/* Basic OHCI-1394 register and port inititalization */
-static inline void __init init_ohci1394_initialize(struct ti_ohci *ohci)
-{
-	quadlet_t bus_options;
-	int num_ports, i;
-
-	/* Put some defaults to these undefined bus options */
-	bus_options = reg_read(ohci, OHCI1394_BusOptions);
-	bus_options |=  0x60000000; /* Enable CMC and ISC */
-	bus_options &= ~0x00ff0000; /* XXX: Set cyc_clk_acc to zero for now */
-	bus_options &= ~0x18000000; /* Disable PMC and BMC */
-	reg_write(ohci, OHCI1394_BusOptions, bus_options);
-
-	/* Set the bus number */
-	reg_write(ohci, OHCI1394_NodeID, 0x0000ffc0);
-
-	/* Enable posted writes */
-	reg_write(ohci, OHCI1394_HCControlSet,
-			OHCI1394_HCControl_postedWriteEnable);
-
-	/* Clear link control register */
-	reg_write(ohci, OHCI1394_LinkControlClear, 0xffffffff);
-
-	/* enable phys */
-	reg_write(ohci, OHCI1394_LinkControlSet,
-			OHCI1394_LinkControl_RcvPhyPkt);
-
-	/* Don't accept phy packets into AR request context */
-	reg_write(ohci, OHCI1394_LinkControlClear, 0x00000400);
-
-	/* Clear the Isochonouys interrupt masks */
-	reg_write(ohci, OHCI1394_IsoRecvIntMaskClear, 0xffffffff);
-	reg_write(ohci, OHCI1394_IsoRecvIntEventClear, 0xffffffff);
-	reg_write(ohci, OHCI1394_IsoXmitIntMaskClear, 0xffffffff);
-	reg_write(ohci, OHCI1394_IsoXmitIntEventClear, 0xffffffff);
-
-	/* Accept asyncronous transfer requests from all nodes for now */
-	reg_write(ohci,OHCI1394_AsReqFilterHiSet, 0x80000000);
-
-	/* Specify asyncronous transfer retries */
-	reg_write(ohci, OHCI1394_ATRetries,
-		  OHCI1394_MAX_AT_REQ_RETRIES |
-		  (OHCI1394_MAX_AT_RESP_RETRIES<<4) |
-		  (OHCI1394_MAX_PHYS_RESP_RETRIES<<8));
-
-	/* We don't want hardware swapping */
-	reg_write(ohci, OHCI1394_HCControlClear, OHCI1394_HCControl_noByteSwap);
-
-	/* Enable link */
-	reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_linkEnable);
-
-	/* If anything is connected to a port, make sure it is enabled */
-	num_ports = get_phy_reg(ohci, 2) & 0xf;
-	for (i = 0; i < num_ports; i++) {
-		unsigned int status;
-
-		set_phy_reg(ohci, 7, i);
-		status = get_phy_reg(ohci, 8);
-
-		if (status & 0x20)
-			set_phy_reg(ohci, 8, status & ~1);
-	}
-}
-
-/**
- * init_ohci1394_wait_for_busresets - wait until bus resets are completed
- *
- * OHCI1394 initialization itself and any device going on- or offline
- * and any cable issue cause a IEEE1394 bus reset. The OHCI1394 spec
- * specifies that physical DMA is disabled on each bus reset and it
- * has to be enabled after each bus reset when needed. We resort
- * to polling here because on early boot, we have no interrupts.
- */
-static inline void __init init_ohci1394_wait_for_busresets(struct ti_ohci *ohci)
-{
-	int i, events;
-
-	for (i=0; i < 9; i++) {
-		mdelay(200);
-		events = reg_read(ohci, OHCI1394_IntEventSet);
-		if (events & OHCI1394_busReset)
-			reg_write(ohci, OHCI1394_IntEventClear,
-					OHCI1394_busReset);
-	}
-}
-
-/**
- * init_ohci1394_enable_physical_dma - Enable physical DMA for remote debugging
- * This enables remote DMA access over IEEE1394 from every host for the low
- * 4GB of address space. DMA accesses above 4GB are not available currently.
- */
-static inline void __init init_ohci1394_enable_physical_dma(struct ti_ohci *hci)
-{
-	reg_write(hci, OHCI1394_PhyReqFilterHiSet, 0xffffffff);
-	reg_write(hci, OHCI1394_PhyReqFilterLoSet, 0xffffffff);
-	reg_write(hci, OHCI1394_PhyUpperBound, 0xffff0000);
-}
-
-/**
- * init_ohci1394_reset_and_init_dma - init controller and enable DMA
- * This initializes the given controller and enables physical DMA engine in it.
- */
-static inline void __init init_ohci1394_reset_and_init_dma(struct ti_ohci *ohci)
-{
-	/* Start off with a soft reset, clears everything to a sane state. */
-	init_ohci1394_soft_reset(ohci);
-
-	/* Accessing some registers without LPS enabled may cause lock up */
-	reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_LPS);
-
-	/* Disable and clear interrupts */
-	reg_write(ohci, OHCI1394_IntEventClear, 0xffffffff);
-	reg_write(ohci, OHCI1394_IntMaskClear, 0xffffffff);
-
-	mdelay(50); /* Wait 50msec to make sure we have full link enabled */
-
-	init_ohci1394_initialize(ohci);
-	/*
-	 * The initialization causes at least one IEEE1394 bus reset. Enabling
-	 * physical DMA only works *after* *all* bus resets have calmed down:
-	 */
-	init_ohci1394_wait_for_busresets(ohci);
-
-	/* We had to wait and do this now if we want to debug early problems */
-	init_ohci1394_enable_physical_dma(ohci);
-}
-
-/**
- * init_ohci1394_controller - Map the registers of the controller and init DMA
- * This maps the registers of the specified controller and initializes it
- */
-static inline void __init init_ohci1394_controller(int num, int slot, int func)
-{
-	unsigned long ohci_base;
-	struct ti_ohci ohci;
-
-	printk(KERN_INFO "init_ohci1394_dma: initializing OHCI-1394"
-			 " at %02x:%02x.%x\n", num, slot, func);
-
-	ohci_base = read_pci_config(num, slot, func, PCI_BASE_ADDRESS_0+(0<<2))
-						   & PCI_BASE_ADDRESS_MEM_MASK;
-
-	set_fixmap_nocache(FIX_OHCI1394_BASE, ohci_base);
-
-	ohci.registers = (void *)fix_to_virt(FIX_OHCI1394_BASE);
-
-	init_ohci1394_reset_and_init_dma(&ohci);
-}
-
-/**
- * debug_init_ohci1394_dma - scan for OHCI1394 controllers and init DMA on them
- * Scans the whole PCI space for OHCI1394 controllers and inits DMA on them
- */
-void __init init_ohci1394_dma_on_all_controllers(void)
-{
-	int num, slot, func;
-
-	if (!early_pci_allowed())
-		return;
-
-	/* Poor man's PCI discovery, the only thing we can do at early boot */
-	for (num = 0; num < 32; num++) {
-		for (slot = 0; slot < 32; slot++) {
-			for (func = 0; func < 8; func++) {
-				u32 class = read_pci_config(num,slot,func,
-							PCI_CLASS_REVISION);
-				if ((class == 0xffffffff))
-					continue; /* No device at this func */
-
-				if (class>>8 != PCI_CLASS_SERIAL_FIREWIRE_OHCI)
-					continue; /* Not an OHCI-1394 device */
-
-				init_ohci1394_controller(num, slot, func);
-				break; /* Assume one controller per device */
-			}
-		}
-	}
-	printk(KERN_INFO "init_ohci1394_dma: finished initializing OHCI DMA\n");
-}
-
-/**
- * setup_init_ohci1394_early - enables early OHCI1394 DMA initialization
- */
-static int __init setup_ohci1394_dma(char *opt)
-{
-	if (!strcmp(opt, "early"))
-		init_ohci1394_dma_early = 1;
-	return 0;
-}
-
-/* passing ohci1394_dma=early on boot causes early OHCI1394 DMA initialization */
-early_param("ohci1394_dma", setup_ohci1394_dma);