media: rc: harmonize infrared durations to microseconds

rc-core kapi uses nanoseconds for infrared durations for receiving, and
microseconds for sending. The uapi already uses microseconds for both,
so this patch does not change the uapi.

Infrared durations do not need nanosecond resolution. IR protocols do not
have durations shorter than about 100 microseconds. Some IR hardware offers
250 microseconds resolution, which is sufficient for most protocols.
Better hardware has 50 microsecond resolution and is enough for every
protocol I am aware off.

Unify on microseconds everywhere. This simplifies the code since less
conversion between microseconds and nanoseconds needs to be done.

This affects:
 - rx_resolution member of struct rc_dev
 - timeout member of struct rc_dev
 - duration member in struct ir_raw_event

Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Patrick Lerda <patrick9876@free.fr>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Benjamin Valentin <benpicco@googlemail.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

1 files changed, 9 insertions, 9 deletions

diff --git a/drivers/media/rc/ene_ir.c b/drivers/media/rc/ene_ir.c
index 82867a2a60b0..6049e5c95394 100644
--- a/drivers/media/rc/ene_ir.c
+++ b/drivers/media/rc/ene_ir.c
@@ -432,27 +432,27 @@ static void ene_rx_setup(struct ene_device *dev)
 
 select_timeout:
 	if (dev->rx_fan_input_inuse) {
-		dev->rdev->rx_resolution = US_TO_NS(ENE_FW_SAMPLE_PERIOD_FAN);
+		dev->rdev->rx_resolution = ENE_FW_SAMPLE_PERIOD_FAN;
 
 		/* Fan input doesn't support timeouts, it just ends the
 			input with a maximum sample */
 		dev->rdev->min_timeout = dev->rdev->max_timeout =
-			US_TO_NS(ENE_FW_SMPL_BUF_FAN_MSK *
-				ENE_FW_SAMPLE_PERIOD_FAN);
+			ENE_FW_SMPL_BUF_FAN_MSK *
+				ENE_FW_SAMPLE_PERIOD_FAN;
 	} else {
-		dev->rdev->rx_resolution = US_TO_NS(sample_period);
+		dev->rdev->rx_resolution = sample_period;
 
 		/* Theoreticly timeout is unlimited, but we cap it
 		 * because it was seen that on one device, it
 		 * would stop sending spaces after around 250 msec.
 		 * Besides, this is close to 2^32 anyway and timeout is u32.
 		 */
-		dev->rdev->min_timeout = US_TO_NS(127 * sample_period);
-		dev->rdev->max_timeout = US_TO_NS(200000);
+		dev->rdev->min_timeout = 127 * sample_period;
+		dev->rdev->max_timeout = 200000;
 	}
 
 	if (dev->hw_learning_and_tx_capable)
-		dev->rdev->tx_resolution = US_TO_NS(sample_period);
+		dev->rdev->tx_resolution = sample_period;
 
 	if (dev->rdev->timeout > dev->rdev->max_timeout)
 		dev->rdev->timeout = dev->rdev->max_timeout;
@@ -798,7 +798,7 @@ static irqreturn_t ene_isr(int irq, void *data)
 
 		dbg("RX: %d (%s)", hw_sample, pulse ? "pulse" : "space");
 
-		ev.duration = US_TO_NS(hw_sample);
+		ev.duration = hw_sample;
 		ev.pulse = pulse;
 		ir_raw_event_store_with_filter(dev->rdev, &ev);
 	}
@@ -818,7 +818,7 @@ static void ene_setup_default_settings(struct ene_device *dev)
 	dev->learning_mode_enabled = learning_mode_force;
 
 	/* Set reasonable default timeout */
-	dev->rdev->timeout = US_TO_NS(150000);
+	dev->rdev->timeout = MS_TO_US(150);
 }
 
 /* Upload all hardware settings at once. Used at load and resume time */