[media] mceusb: report actual tx frequencies

Rather than dumping out hex values, lets print the actual calculated
frequency and period the hardware has been configured for. After this

[ 2643.276215] mceusb 3-1:1.0: tx data: 9f 07 (length=2)
[ 2643.276218] mceusb 3-1:1.0: Get carrier mode and freq
[ 2643.277206] mceusb 3-1:1.0: rx data: 9f 06 01 42 (length=4)
[ 2643.277209] mceusb 3-1:1.0: Got carrier of 37037 Hz (period 27us)

Matches up perfectly with the table in Microsoft's docs.

Of course, I've noticed on one of my devices that the MS-recommended
default value of 1 for carrier pre-scaler and 66 for carrier period was
butchered, and instead of converting 66 to hex (0x42 like above), they
put in 0x66, so the hardware reports a default carrier of 24390Hz.
Fortunately, I guess, this particular device is rx-only, but I wouldn't
put it past other hw to screw up here too.

Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

1 files changed, 11 insertions, 5 deletions

diff --git a/drivers/media/rc/mceusb.c b/drivers/media/rc/mceusb.c
index 8fa5a725bed7..e51637f46ab2 100644
--- a/drivers/media/rc/mceusb.c
+++ b/drivers/media/rc/mceusb.c
@@ -516,6 +516,7 @@ static void mceusb_dev_printdata(struct mceusb_dev *ir, char *buf,
 	u8 cmd, subcmd, data1, data2, data3, data4, data5;
 	struct device *dev = ir->dev;
 	int i, start, skip = 0;
+	u32 carrier, period;
 
 	if (!debug)
 		return;
@@ -613,9 +614,14 @@ static void mceusb_dev_printdata(struct mceusb_dev *ir, char *buf,
 			dev_info(dev, "Resp to 9f 05 of 0x%02x 0x%02x\n",
 				 data1, data2);
 			break;
-		case MCE_CMD_SETIRCFS:
-			dev_info(dev, "%s carrier mode and freq of "
-				 "0x%02x 0x%02x\n", inout, data1, data2);
+		case MCE_RSP_EQIRCFS:
+			period = DIV_ROUND_CLOSEST(
+					(1 << data1 * 2) * (data2 + 1), 10);
+			if (!period)
+				break;
+			carrier = (1000 * 1000) / period;
+			dev_info(dev, "%s carrier of %u Hz (period %uus)\n",
+				 inout, carrier, period);
 			break;
 		case MCE_CMD_GETIRCFS:
 			dev_info(dev, "Get carrier mode and freq\n");
@@ -626,9 +632,9 @@ static void mceusb_dev_printdata(struct mceusb_dev *ir, char *buf,
 			break;
 		case MCE_RSP_EQIRTIMEOUT:
 			/* value is in units of 50us, so x*50/1000 ms */
+			period = ((data1 << 8) | data2) * MCE_TIME_UNIT / 1000;
 			dev_info(dev, "%s receive timeout of %d ms\n",
-				 inout,
-				 ((data1 << 8) | data2) * MCE_TIME_UNIT / 1000);
+				 inout, period);
 			break;
 		case MCE_CMD_GETIRTIMEOUT:
 			dev_info(dev, "Get receive timeout\n");