Merge branch 'linus' into idle-test

1 files changed, 932 insertions, 0 deletions

diff --git a/drivers/media/rc/winbond-cir.c b/drivers/media/rc/winbond-cir.c
new file mode 100644
index 000000000000..186de5522001
--- /dev/null
+++ b/drivers/media/rc/winbond-cir.c
@@ -0,0 +1,932 @@
+/*
+ *  winbond-cir.c - Driver for the Consumer IR functionality of Winbond
+ *                  SuperI/O chips.
+ *
+ *  Currently supports the Winbond WPCD376i chip (PNP id WEC1022), but
+ *  could probably support others (Winbond WEC102X, NatSemi, etc)
+ *  with minor modifications.
+ *
+ *  Original Author: David Härdeman <david@hardeman.nu>
+ *     Copyright (C) 2009 - 2010 David Härdeman <david@hardeman.nu>
+ *
+ *  Dedicated to my daughter Matilda, without whose loving attention this
+ *  driver would have been finished in half the time and with a fraction
+ *  of the bugs.
+ *
+ *  Written using:
+ *    o Winbond WPCD376I datasheet helpfully provided by Jesse Barnes at Intel
+ *    o NatSemi PC87338/PC97338 datasheet (for the serial port stuff)
+ *    o DSDT dumps
+ *
+ *  Supported features:
+ *    o Wake-On-CIR functionality
+ *
+ *  To do:
+ *    o Learning
+ *    o IR Transmit
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/pnp.h>
+#include <linux/interrupt.h>
+#include <linux/timer.h>
+#include <linux/leds.h>
+#include <linux/spinlock.h>
+#include <linux/pci_ids.h>
+#include <linux/io.h>
+#include <linux/bitrev.h>
+#include <linux/slab.h>
+#include <media/rc-core.h>
+
+#define DRVNAME "winbond-cir"
+
+/* CEIR Wake-Up Registers, relative to data->wbase                      */
+#define WBCIR_REG_WCEIR_CTL	0x03 /* CEIR Receiver Control		*/
+#define WBCIR_REG_WCEIR_STS	0x04 /* CEIR Receiver Status		*/
+#define WBCIR_REG_WCEIR_EV_EN	0x05 /* CEIR Receiver Event Enable	*/
+#define WBCIR_REG_WCEIR_CNTL	0x06 /* CEIR Receiver Counter Low	*/
+#define WBCIR_REG_WCEIR_CNTH	0x07 /* CEIR Receiver Counter High	*/
+#define WBCIR_REG_WCEIR_INDEX	0x08 /* CEIR Receiver Index		*/
+#define WBCIR_REG_WCEIR_DATA	0x09 /* CEIR Receiver Data		*/
+#define WBCIR_REG_WCEIR_CSL	0x0A /* CEIR Re. Compare Strlen		*/
+#define WBCIR_REG_WCEIR_CFG1	0x0B /* CEIR Re. Configuration 1	*/
+#define WBCIR_REG_WCEIR_CFG2	0x0C /* CEIR Re. Configuration 2	*/
+
+/* CEIR Enhanced Functionality Registers, relative to data->ebase       */
+#define WBCIR_REG_ECEIR_CTS	0x00 /* Enhanced IR Control Status	*/
+#define WBCIR_REG_ECEIR_CCTL	0x01 /* Infrared Counter Control	*/
+#define WBCIR_REG_ECEIR_CNT_LO	0x02 /* Infrared Counter LSB		*/
+#define WBCIR_REG_ECEIR_CNT_HI	0x03 /* Infrared Counter MSB		*/
+#define WBCIR_REG_ECEIR_IREM	0x04 /* Infrared Emitter Status		*/
+
+/* SP3 Banked Registers, relative to data->sbase                        */
+#define WBCIR_REG_SP3_BSR	0x03 /* Bank Select, all banks		*/
+				      /* Bank 0				*/
+#define WBCIR_REG_SP3_RXDATA	0x00 /* FIFO RX data (r)		*/
+#define WBCIR_REG_SP3_TXDATA	0x00 /* FIFO TX data (w)		*/
+#define WBCIR_REG_SP3_IER	0x01 /* Interrupt Enable		*/
+#define WBCIR_REG_SP3_EIR	0x02 /* Event Identification (r)	*/
+#define WBCIR_REG_SP3_FCR	0x02 /* FIFO Control (w)		*/
+#define WBCIR_REG_SP3_MCR	0x04 /* Mode Control			*/
+#define WBCIR_REG_SP3_LSR	0x05 /* Link Status			*/
+#define WBCIR_REG_SP3_MSR	0x06 /* Modem Status			*/
+#define WBCIR_REG_SP3_ASCR	0x07 /* Aux Status and Control		*/
+				      /* Bank 2				*/
+#define WBCIR_REG_SP3_BGDL	0x00 /* Baud Divisor LSB		*/
+#define WBCIR_REG_SP3_BGDH	0x01 /* Baud Divisor MSB		*/
+#define WBCIR_REG_SP3_EXCR1	0x02 /* Extended Control 1		*/
+#define WBCIR_REG_SP3_EXCR2	0x04 /* Extended Control 2		*/
+#define WBCIR_REG_SP3_TXFLV	0x06 /* TX FIFO Level			*/
+#define WBCIR_REG_SP3_RXFLV	0x07 /* RX FIFO Level			*/
+				      /* Bank 3				*/
+#define WBCIR_REG_SP3_MRID	0x00 /* Module Identification		*/
+#define WBCIR_REG_SP3_SH_LCR	0x01 /* LCR Shadow			*/
+#define WBCIR_REG_SP3_SH_FCR	0x02 /* FCR Shadow			*/
+				      /* Bank 4				*/
+#define WBCIR_REG_SP3_IRCR1	0x02 /* Infrared Control 1		*/
+				      /* Bank 5				*/
+#define WBCIR_REG_SP3_IRCR2	0x04 /* Infrared Control 2		*/
+				      /* Bank 6				*/
+#define WBCIR_REG_SP3_IRCR3	0x00 /* Infrared Control 3		*/
+#define WBCIR_REG_SP3_SIR_PW	0x02 /* SIR Pulse Width			*/
+				      /* Bank 7				*/
+#define WBCIR_REG_SP3_IRRXDC	0x00 /* IR RX Demod Control		*/
+#define WBCIR_REG_SP3_IRTXMC	0x01 /* IR TX Mod Control		*/
+#define WBCIR_REG_SP3_RCCFG	0x02 /* CEIR Config			*/
+#define WBCIR_REG_SP3_IRCFG1	0x04 /* Infrared Config 1		*/
+#define WBCIR_REG_SP3_IRCFG4	0x07 /* Infrared Config 4		*/
+
+/*
+ * Magic values follow
+ */
+
+/* No interrupts for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
+#define WBCIR_IRQ_NONE		0x00
+/* RX data bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
+#define WBCIR_IRQ_RX		0x01
+/* Over/Under-flow bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
+#define WBCIR_IRQ_ERR		0x04
+/* Led enable/disable bit for WBCIR_REG_ECEIR_CTS */
+#define WBCIR_LED_ENABLE	0x80
+/* RX data available bit for WBCIR_REG_SP3_LSR */
+#define WBCIR_RX_AVAIL		0x01
+/* RX disable bit for WBCIR_REG_SP3_ASCR */
+#define WBCIR_RX_DISABLE	0x20
+/* Extended mode enable bit for WBCIR_REG_SP3_EXCR1 */
+#define WBCIR_EXT_ENABLE	0x01
+/* Select compare register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */
+#define WBCIR_REGSEL_COMPARE	0x10
+/* Select mask register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */
+#define WBCIR_REGSEL_MASK	0x20
+/* Starting address of selected register in WBCIR_REG_WCEIR_INDEX */
+#define WBCIR_REG_ADDR0		0x00
+
+/* Valid banks for the SP3 UART */
+enum wbcir_bank {
+	WBCIR_BANK_0          = 0x00,
+	WBCIR_BANK_1          = 0x80,
+	WBCIR_BANK_2          = 0xE0,
+	WBCIR_BANK_3          = 0xE4,
+	WBCIR_BANK_4          = 0xE8,
+	WBCIR_BANK_5          = 0xEC,
+	WBCIR_BANK_6          = 0xF0,
+	WBCIR_BANK_7          = 0xF4,
+};
+
+/* Supported power-on IR Protocols */
+enum wbcir_protocol {
+	IR_PROTOCOL_RC5          = 0x0,
+	IR_PROTOCOL_NEC          = 0x1,
+	IR_PROTOCOL_RC6          = 0x2,
+};
+
+/* Misc */
+#define WBCIR_NAME	"Winbond CIR"
+#define WBCIR_ID_FAMILY          0xF1 /* Family ID for the WPCD376I	*/
+#define	WBCIR_ID_CHIP            0x04 /* Chip ID for the WPCD376I	*/
+#define INVALID_SCANCODE   0x7FFFFFFF /* Invalid with all protos	*/
+#define WAKEUP_IOMEM_LEN         0x10 /* Wake-Up I/O Reg Len		*/
+#define EHFUNC_IOMEM_LEN         0x10 /* Enhanced Func I/O Reg Len	*/
+#define SP_IOMEM_LEN             0x08 /* Serial Port 3 (IR) Reg Len	*/
+
+/* Per-device data */
+struct wbcir_data {
+	spinlock_t spinlock;
+
+	unsigned long wbase;        /* Wake-Up Baseaddr		*/
+	unsigned long ebase;        /* Enhanced Func. Baseaddr	*/
+	unsigned long sbase;        /* Serial Port Baseaddr	*/
+	unsigned int  irq;          /* Serial Port IRQ		*/
+
+	struct rc_dev *dev;
+
+	struct led_trigger *rxtrigger;
+	struct led_trigger *txtrigger;
+	struct led_classdev led;
+
+	/* RX irdata state */
+	bool irdata_active;
+	bool irdata_error;
+	struct ir_raw_event ev;
+};
+
+static enum wbcir_protocol protocol = IR_PROTOCOL_RC6;
+module_param(protocol, uint, 0444);
+MODULE_PARM_DESC(protocol, "IR protocol to use for the power-on command "
+		 "(0 = RC5, 1 = NEC, 2 = RC6A, default)");
+
+static int invert; /* default = 0 */
+module_param(invert, bool, 0444);
+MODULE_PARM_DESC(invert, "Invert the signal from the IR receiver");
+
+static unsigned int wake_sc = 0x800F040C;
+module_param(wake_sc, uint, 0644);
+MODULE_PARM_DESC(wake_sc, "Scancode of the power-on IR command");
+
+static unsigned int wake_rc6mode = 6;
+module_param(wake_rc6mode, uint, 0644);
+MODULE_PARM_DESC(wake_rc6mode, "RC6 mode for the power-on command "
+		 "(0 = 0, 6 = 6A, default)");
+
+
+
+/*****************************************************************************
+ *
+ * UTILITY FUNCTIONS
+ *
+ *****************************************************************************/
+
+/* Caller needs to hold wbcir_lock */
+static void
+wbcir_set_bits(unsigned long addr, u8 bits, u8 mask)
+{
+	u8 val;
+
+	val = inb(addr);
+	val = ((val & ~mask) | (bits & mask));
+	outb(val, addr);
+}
+
+/* Selects the register bank for the serial port */
+static inline void
+wbcir_select_bank(struct wbcir_data *data, enum wbcir_bank bank)
+{
+	outb(bank, data->sbase + WBCIR_REG_SP3_BSR);
+}
+
+static enum led_brightness
+wbcir_led_brightness_get(struct led_classdev *led_cdev)
+{
+	struct wbcir_data *data = container_of(led_cdev,
+					       struct wbcir_data,
+					       led);
+
+	if (inb(data->ebase + WBCIR_REG_ECEIR_CTS) & WBCIR_LED_ENABLE)
+		return LED_FULL;
+	else
+		return LED_OFF;
+}
+
+static void
+wbcir_led_brightness_set(struct led_classdev *led_cdev,
+			 enum led_brightness brightness)
+{
+	struct wbcir_data *data = container_of(led_cdev,
+					       struct wbcir_data,
+					       led);
+
+	wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS,
+		       brightness == LED_OFF ? 0x00 : WBCIR_LED_ENABLE,
+		       WBCIR_LED_ENABLE);
+}
+
+/* Manchester encodes bits to RC6 message cells (see wbcir_shutdown) */
+static u8
+wbcir_to_rc6cells(u8 val)
+{
+	u8 coded = 0x00;
+	int i;
+
+	val &= 0x0F;
+	for (i = 0; i < 4; i++) {
+		if (val & 0x01)
+			coded |= 0x02 << (i * 2);
+		else
+			coded |= 0x01 << (i * 2);
+		val >>= 1;
+	}
+
+	return coded;
+}
+
+/*****************************************************************************
+ *
+ * INTERRUPT FUNCTIONS
+ *
+ *****************************************************************************/
+
+static irqreturn_t
+wbcir_irq_handler(int irqno, void *cookie)
+{
+	struct pnp_dev *device = cookie;
+	struct wbcir_data *data = pnp_get_drvdata(device);
+	unsigned long flags;
+	u8 irdata[8];
+	u8 disable = true;
+	u8 status;
+	int i;
+
+	spin_lock_irqsave(&data->spinlock, flags);
+
+	wbcir_select_bank(data, WBCIR_BANK_0);
+
+	status = inb(data->sbase + WBCIR_REG_SP3_EIR);
+
+	if (!(status & (WBCIR_IRQ_RX | WBCIR_IRQ_ERR))) {
+		spin_unlock_irqrestore(&data->spinlock, flags);
+		return IRQ_NONE;
+	}
+
+	/* Check for e.g. buffer overflow */
+	if (status & WBCIR_IRQ_ERR) {
+		data->irdata_error = true;
+		ir_raw_event_reset(data->dev);
+	}
+
+	if (!(status & WBCIR_IRQ_RX))
+		goto out;
+
+	if (!data->irdata_active) {
+		data->irdata_active = true;
+		led_trigger_event(data->rxtrigger, LED_FULL);
+	}
+
+	/* Since RXHDLEV is set, at least 8 bytes are in the FIFO */
+	insb(data->sbase + WBCIR_REG_SP3_RXDATA, &irdata[0], 8);
+
+	for (i = 0; i < 8; i++) {
+		u8 pulse;
+		u32 duration;
+
+		if (irdata[i] != 0xFF && irdata[i] != 0x00)
+			disable = false;
+
+		if (data->irdata_error)
+			continue;
+
+		pulse = irdata[i] & 0x80 ? false : true;
+		duration = (irdata[i] & 0x7F) * 10000; /* ns */
+
+		if (data->ev.pulse != pulse) {
+			if (data->ev.duration != 0) {
+				ir_raw_event_store(data->dev, &data->ev);
+				data->ev.duration = 0;
+			}
+
+			data->ev.pulse = pulse;
+		}
+
+		data->ev.duration += duration;
+	}
+
+	if (disable) {
+		if (data->ev.duration != 0 && !data->irdata_error) {
+			ir_raw_event_store(data->dev, &data->ev);
+			data->ev.duration = 0;
+		}
+
+		/* Set RXINACTIVE */
+		outb(WBCIR_RX_DISABLE, data->sbase + WBCIR_REG_SP3_ASCR);
+
+		/* Drain the FIFO */
+		while (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_AVAIL)
+			inb(data->sbase + WBCIR_REG_SP3_RXDATA);
+
+		ir_raw_event_reset(data->dev);
+		data->irdata_error = false;
+		data->irdata_active = false;
+		led_trigger_event(data->rxtrigger, LED_OFF);
+	}
+
+	ir_raw_event_handle(data->dev);
+
+out:
+	spin_unlock_irqrestore(&data->spinlock, flags);
+	return IRQ_HANDLED;
+}
+
+
+
+/*****************************************************************************
+ *
+ * SETUP/INIT/SUSPEND/RESUME FUNCTIONS
+ *
+ *****************************************************************************/
+
+static void
+wbcir_shutdown(struct pnp_dev *device)
+{
+	struct device *dev = &device->dev;
+	struct wbcir_data *data = pnp_get_drvdata(device);
+	int do_wake = 1;
+	u8 match[11];
+	u8 mask[11];
+	u8 rc6_csl = 0;
+	int i;
+
+	memset(match, 0, sizeof(match));
+	memset(mask, 0, sizeof(mask));
+
+	if (wake_sc == INVALID_SCANCODE || !device_may_wakeup(dev)) {
+		do_wake = 0;
+		goto finish;
+	}
+
+	switch (protocol) {
+	case IR_PROTOCOL_RC5:
+		if (wake_sc > 0xFFF) {
+			do_wake = 0;
+			dev_err(dev, "RC5 - Invalid wake scancode\n");
+			break;
+		}
+
+		/* Mask = 13 bits, ex toggle */
+		mask[0] = 0xFF;
+		mask[1] = 0x17;
+
+		match[0]  = (wake_sc & 0x003F);      /* 6 command bits */
+		match[0] |= (wake_sc & 0x0180) >> 1; /* 2 address bits */
+		match[1]  = (wake_sc & 0x0E00) >> 9; /* 3 address bits */
+		if (!(wake_sc & 0x0040))             /* 2nd start bit  */
+			match[1] |= 0x10;
+
+		break;
+
+	case IR_PROTOCOL_NEC:
+		if (wake_sc > 0xFFFFFF) {
+			do_wake = 0;
+			dev_err(dev, "NEC - Invalid wake scancode\n");
+			break;
+		}
+
+		mask[0] = mask[1] = mask[2] = mask[3] = 0xFF;
+
+		match[1] = bitrev8((wake_sc & 0xFF));
+		match[0] = ~match[1];
+
+		match[3] = bitrev8((wake_sc & 0xFF00) >> 8);
+		if (wake_sc > 0xFFFF)
+			match[2] = bitrev8((wake_sc & 0xFF0000) >> 16);
+		else
+			match[2] = ~match[3];
+
+		break;
+
+	case IR_PROTOCOL_RC6:
+
+		if (wake_rc6mode == 0) {
+			if (wake_sc > 0xFFFF) {
+				do_wake = 0;
+				dev_err(dev, "RC6 - Invalid wake scancode\n");
+				break;
+			}
+
+			/* Command */
+			match[0] = wbcir_to_rc6cells(wake_sc >>  0);
+			mask[0]  = 0xFF;
+			match[1] = wbcir_to_rc6cells(wake_sc >>  4);
+			mask[1]  = 0xFF;
+
+			/* Address */
+			match[2] = wbcir_to_rc6cells(wake_sc >>  8);
+			mask[2]  = 0xFF;
+			match[3] = wbcir_to_rc6cells(wake_sc >> 12);
+			mask[3]  = 0xFF;
+
+			/* Header */
+			match[4] = 0x50; /* mode1 = mode0 = 0, ignore toggle */
+			mask[4]  = 0xF0;
+			match[5] = 0x09; /* start bit = 1, mode2 = 0 */
+			mask[5]  = 0x0F;
+
+			rc6_csl = 44;
+
+		} else if (wake_rc6mode == 6) {
+			i = 0;
+
+			/* Command */
+			match[i]  = wbcir_to_rc6cells(wake_sc >>  0);
+			mask[i++] = 0xFF;
+			match[i]  = wbcir_to_rc6cells(wake_sc >>  4);
+			mask[i++] = 0xFF;
+
+			/* Address + Toggle */
+			match[i]  = wbcir_to_rc6cells(wake_sc >>  8);
+			mask[i++] = 0xFF;
+			match[i]  = wbcir_to_rc6cells(wake_sc >> 12);
+			mask[i++] = 0x3F;
+
+			/* Customer bits 7 - 0 */
+			match[i]  = wbcir_to_rc6cells(wake_sc >> 16);
+			mask[i++] = 0xFF;
+			match[i]  = wbcir_to_rc6cells(wake_sc >> 20);
+			mask[i++] = 0xFF;
+
+			if (wake_sc & 0x80000000) {
+				/* Customer range bit and bits 15 - 8 */
+				match[i]  = wbcir_to_rc6cells(wake_sc >> 24);
+				mask[i++] = 0xFF;
+				match[i]  = wbcir_to_rc6cells(wake_sc >> 28);
+				mask[i++] = 0xFF;
+				rc6_csl = 76;
+			} else if (wake_sc <= 0x007FFFFF) {
+				rc6_csl = 60;
+			} else {
+				do_wake = 0;
+				dev_err(dev, "RC6 - Invalid wake scancode\n");
+				break;
+			}
+
+			/* Header */
+			match[i]  = 0x93; /* mode1 = mode0 = 1, submode = 0 */
+			mask[i++] = 0xFF;
+			match[i]  = 0x0A; /* start bit = 1, mode2 = 1 */
+			mask[i++] = 0x0F;
+
+		} else {
+			do_wake = 0;
+			dev_err(dev, "RC6 - Invalid wake mode\n");
+		}
+
+		break;
+
+	default:
+		do_wake = 0;
+		break;
+	}
+
+finish:
+	if (do_wake) {
+		/* Set compare and compare mask */
+		wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX,
+			       WBCIR_REGSEL_COMPARE | WBCIR_REG_ADDR0,
+			       0x3F);
+		outsb(data->wbase + WBCIR_REG_WCEIR_DATA, match, 11);
+		wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX,
+			       WBCIR_REGSEL_MASK | WBCIR_REG_ADDR0,
+			       0x3F);
+		outsb(data->wbase + WBCIR_REG_WCEIR_DATA, mask, 11);
+
+		/* RC6 Compare String Len */
+		outb(rc6_csl, data->wbase + WBCIR_REG_WCEIR_CSL);
+
+		/* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */
+		wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17);
+
+		/* Clear BUFF_EN, Clear END_EN, Set MATCH_EN */
+		wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x01, 0x07);
+
+		/* Set CEIR_EN */
+		wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x01, 0x01);
+
+	} else {
+		/* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */
+		wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
+
+		/* Clear CEIR_EN */
+		wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01);
+	}
+
+	/* Disable interrupts */
+	wbcir_select_bank(data, WBCIR_BANK_0);
+	outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER);
+
+	/* Disable LED */
+	data->irdata_active = false;
+	led_trigger_event(data->rxtrigger, LED_OFF);
+
+	/*
+	 * ACPI will set the HW disable bit for SP3 which means that the
+	 * output signals are left in an undefined state which may cause
+	 * spurious interrupts which we need to ignore until the hardware
+	 * is reinitialized.
+	 */
+	disable_irq(data->irq);
+}
+
+static int
+wbcir_suspend(struct pnp_dev *device, pm_message_t state)
+{
+	wbcir_shutdown(device);
+	return 0;
+}
+
+static void
+wbcir_init_hw(struct wbcir_data *data)
+{
+	u8 tmp;
+
+	/* Disable interrupts */
+	wbcir_select_bank(data, WBCIR_BANK_0);
+	outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER);
+
+	/* Set PROT_SEL, RX_INV, Clear CEIR_EN (needed for the led) */
+	tmp = protocol << 4;
+	if (invert)
+		tmp |= 0x08;
+	outb(tmp, data->wbase + WBCIR_REG_WCEIR_CTL);
+
+	/* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */
+	wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17);
+
+	/* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */
+	wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
+
+	/* Set RC5 cell time to correspond to 36 kHz */
+	wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CFG1, 0x4A, 0x7F);
+
+	/* Set IRTX_INV */
+	if (invert)
+		outb(0x04, data->ebase + WBCIR_REG_ECEIR_CCTL);
+	else
+		outb(0x00, data->ebase + WBCIR_REG_ECEIR_CCTL);
+
+	/*
+	 * Clear IR LED, set SP3 clock to 24Mhz
+	 * set SP3_IRRX_SW to binary 01, helpfully not documented
+	 */
+	outb(0x10, data->ebase + WBCIR_REG_ECEIR_CTS);
+
+	/* Enable extended mode */
+	wbcir_select_bank(data, WBCIR_BANK_2);
+	outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1);
+
+	/*
+	 * Configure baud generator, IR data will be sampled at
+	 * a bitrate of: (24Mhz * prescaler) / (divisor * 16).
+	 *
+	 * The ECIR registers include a flag to change the
+	 * 24Mhz clock freq to 48Mhz.
+	 *
+	 * It's not documented in the specs, but fifo levels
+	 * other than 16 seems to be unsupported.
+	 */
+
+	/* prescaler 1.0, tx/rx fifo lvl 16 */
+	outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2);
+
+	/* Set baud divisor to generate one byte per bit/cell */
+	switch (protocol) {
+	case IR_PROTOCOL_RC5:
+		outb(0xA7, data->sbase + WBCIR_REG_SP3_BGDL);
+		break;
+	case IR_PROTOCOL_RC6:
+		outb(0x53, data->sbase + WBCIR_REG_SP3_BGDL);
+		break;
+	case IR_PROTOCOL_NEC:
+		outb(0x69, data->sbase + WBCIR_REG_SP3_BGDL);
+		break;
+	}
+	outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH);
+
+	/* Set CEIR mode */
+	wbcir_select_bank(data, WBCIR_BANK_0);
+	outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR);
+	inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */
+	inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */
+
+	/* Disable RX demod, run-length encoding/decoding, set freq span */
+	wbcir_select_bank(data, WBCIR_BANK_7);
+	outb(0x10, data->sbase + WBCIR_REG_SP3_RCCFG);
+
+	/* Disable timer */
+	wbcir_select_bank(data, WBCIR_BANK_4);
+	outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1);
+
+	/* Enable MSR interrupt, Clear AUX_IRX */
+	wbcir_select_bank(data, WBCIR_BANK_5);
+	outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR2);
+
+	/* Disable CRC */
+	wbcir_select_bank(data, WBCIR_BANK_6);
+	outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3);
+
+	/* Set RX/TX (de)modulation freq, not really used */
+	wbcir_select_bank(data, WBCIR_BANK_7);
+	outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC);
+	outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC);
+
+	/* Set invert and pin direction */
+	if (invert)
+		outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4);
+	else
+		outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4);
+
+	/* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */
+	wbcir_select_bank(data, WBCIR_BANK_0);
+	outb(0x97, data->sbase + WBCIR_REG_SP3_FCR);
+
+	/* Clear AUX status bits */
+	outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR);
+
+	/* Clear IR decoding state */
+	data->irdata_active = false;
+	led_trigger_event(data->rxtrigger, LED_OFF);
+	data->irdata_error = false;
+	data->ev.duration = 0;
+	ir_raw_event_reset(data->dev);
+	ir_raw_event_handle(data->dev);
+
+	/* Enable interrupts */
+	outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER);
+}
+
+static int
+wbcir_resume(struct pnp_dev *device)
+{
+	struct wbcir_data *data = pnp_get_drvdata(device);
+
+	wbcir_init_hw(data);
+	enable_irq(data->irq);
+
+	return 0;
+}
+
+static int __devinit
+wbcir_probe(struct pnp_dev *device, const struct pnp_device_id *dev_id)
+{
+	struct device *dev = &device->dev;
+	struct wbcir_data *data;
+	int err;
+
+	if (!(pnp_port_len(device, 0) == EHFUNC_IOMEM_LEN &&
+	      pnp_port_len(device, 1) == WAKEUP_IOMEM_LEN &&
+	      pnp_port_len(device, 2) == SP_IOMEM_LEN)) {
+		dev_err(dev, "Invalid resources\n");
+		return -ENODEV;
+	}
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data) {
+		err = -ENOMEM;
+		goto exit;
+	}
+
+	pnp_set_drvdata(device, data);
+
+	spin_lock_init(&data->spinlock);
+	data->ebase = pnp_port_start(device, 0);
+	data->wbase = pnp_port_start(device, 1);
+	data->sbase = pnp_port_start(device, 2);
+	data->irq = pnp_irq(device, 0);
+
+	if (data->wbase == 0 || data->ebase == 0 ||
+	    data->sbase == 0 || data->irq == 0) {
+		err = -ENODEV;
+		dev_err(dev, "Invalid resources\n");
+		goto exit_free_data;
+	}
+
+	dev_dbg(&device->dev, "Found device "
+		"(w: 0x%lX, e: 0x%lX, s: 0x%lX, i: %u)\n",
+		data->wbase, data->ebase, data->sbase, data->irq);
+
+	if (!request_region(data->wbase, WAKEUP_IOMEM_LEN, DRVNAME)) {
+		dev_err(dev, "Region 0x%lx-0x%lx already in use!\n",
+			data->wbase, data->wbase + WAKEUP_IOMEM_LEN - 1);
+		err = -EBUSY;
+		goto exit_free_data;
+	}
+
+	if (!request_region(data->ebase, EHFUNC_IOMEM_LEN, DRVNAME)) {
+		dev_err(dev, "Region 0x%lx-0x%lx already in use!\n",
+			data->ebase, data->ebase + EHFUNC_IOMEM_LEN - 1);
+		err = -EBUSY;
+		goto exit_release_wbase;
+	}
+
+	if (!request_region(data->sbase, SP_IOMEM_LEN, DRVNAME)) {
+		dev_err(dev, "Region 0x%lx-0x%lx already in use!\n",
+			data->sbase, data->sbase + SP_IOMEM_LEN - 1);
+		err = -EBUSY;
+		goto exit_release_ebase;
+	}
+
+	err = request_irq(data->irq, wbcir_irq_handler,
+			  IRQF_DISABLED, DRVNAME, device);
+	if (err) {
+		dev_err(dev, "Failed to claim IRQ %u\n", data->irq);
+		err = -EBUSY;
+		goto exit_release_sbase;
+	}
+
+	led_trigger_register_simple("cir-tx", &data->txtrigger);
+	if (!data->txtrigger) {
+		err = -ENOMEM;
+		goto exit_free_irq;
+	}
+
+	led_trigger_register_simple("cir-rx", &data->rxtrigger);
+	if (!data->rxtrigger) {
+		err = -ENOMEM;
+		goto exit_unregister_txtrigger;
+	}
+
+	data->led.name = "cir::activity";
+	data->led.default_trigger = "cir-rx";
+	data->led.brightness_set = wbcir_led_brightness_set;
+	data->led.brightness_get = wbcir_led_brightness_get;
+	err = led_classdev_register(&device->dev, &data->led);
+	if (err)
+		goto exit_unregister_rxtrigger;
+
+	data->dev = rc_allocate_device();
+	if (!data->dev) {
+		err = -ENOMEM;
+		goto exit_unregister_led;
+	}
+
+	data->dev->driver_name = WBCIR_NAME;
+	data->dev->input_name = WBCIR_NAME;
+	data->dev->input_phys = "wbcir/cir0";
+	data->dev->input_id.bustype = BUS_HOST;
+	data->dev->input_id.vendor = PCI_VENDOR_ID_WINBOND;
+	data->dev->input_id.product = WBCIR_ID_FAMILY;
+	data->dev->input_id.version = WBCIR_ID_CHIP;
+	data->dev->priv = data;
+	data->dev->dev.parent = &device->dev;
+
+	err = rc_register_device(data->dev);
+	if (err)
+		goto exit_free_rc;
+
+	device_init_wakeup(&device->dev, 1);
+
+	wbcir_init_hw(data);
+
+	return 0;
+
+exit_free_rc:
+	rc_free_device(data->dev);
+exit_unregister_led:
+	led_classdev_unregister(&data->led);
+exit_unregister_rxtrigger:
+	led_trigger_unregister_simple(data->rxtrigger);
+exit_unregister_txtrigger:
+	led_trigger_unregister_simple(data->txtrigger);
+exit_free_irq:
+	free_irq(data->irq, device);
+exit_release_sbase:
+	release_region(data->sbase, SP_IOMEM_LEN);
+exit_release_ebase:
+	release_region(data->ebase, EHFUNC_IOMEM_LEN);
+exit_release_wbase:
+	release_region(data->wbase, WAKEUP_IOMEM_LEN);
+exit_free_data:
+	kfree(data);
+	pnp_set_drvdata(device, NULL);
+exit:
+	return err;
+}
+
+static void __devexit
+wbcir_remove(struct pnp_dev *device)
+{
+	struct wbcir_data *data = pnp_get_drvdata(device);
+
+	/* Disable interrupts */
+	wbcir_select_bank(data, WBCIR_BANK_0);
+	outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER);
+
+	free_irq(data->irq, device);
+
+	/* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */
+	wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17);
+
+	/* Clear CEIR_EN */
+	wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01);
+
+	/* Clear BUFF_EN, END_EN, MATCH_EN */
+	wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
+
+	rc_unregister_device(data->dev);
+
+	led_trigger_unregister_simple(data->rxtrigger);
+	led_trigger_unregister_simple(data->txtrigger);
+	led_classdev_unregister(&data->led);
+
+	/* This is ok since &data->led isn't actually used */
+	wbcir_led_brightness_set(&data->led, LED_OFF);
+
+	release_region(data->wbase, WAKEUP_IOMEM_LEN);
+	release_region(data->ebase, EHFUNC_IOMEM_LEN);
+	release_region(data->sbase, SP_IOMEM_LEN);
+
+	kfree(data);
+
+	pnp_set_drvdata(device, NULL);
+}
+
+static const struct pnp_device_id wbcir_ids[] = {
+	{ "WEC1022", 0 },
+	{ "", 0 }
+};
+MODULE_DEVICE_TABLE(pnp, wbcir_ids);
+
+static struct pnp_driver wbcir_driver = {
+	.name     = WBCIR_NAME,
+	.id_table = wbcir_ids,
+	.probe    = wbcir_probe,
+	.remove   = __devexit_p(wbcir_remove),
+	.suspend  = wbcir_suspend,
+	.resume   = wbcir_resume,
+	.shutdown = wbcir_shutdown
+};
+
+static int __init
+wbcir_init(void)
+{
+	int ret;
+
+	switch (protocol) {
+	case IR_PROTOCOL_RC5:
+	case IR_PROTOCOL_NEC:
+	case IR_PROTOCOL_RC6:
+		break;
+	default:
+		printk(KERN_ERR DRVNAME ": Invalid power-on protocol\n");
+	}
+
+	ret = pnp_register_driver(&wbcir_driver);
+	if (ret)
+		printk(KERN_ERR DRVNAME ": Unable to register driver\n");
+
+	return ret;
+}
+
+static void __exit
+wbcir_exit(void)
+{
+	pnp_unregister_driver(&wbcir_driver);
+}
+
+module_init(wbcir_init);
+module_exit(wbcir_exit);
+
+MODULE_AUTHOR("David Härdeman <david@hardeman.nu>");
+MODULE_DESCRIPTION("Winbond SuperI/O Consumer IR Driver");
+MODULE_LICENSE("GPL");