Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.15:

  Core:
   - CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
   - DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
   - Add GPIO descriptor based slot-gpio card detect API

  Drivers:
   - dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
   - mmci: Support HW busy detection on ux500
   - omap: Support MMC_ERASE
   - omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
   - rtsx: Support pre-req/post-req async
   - sdhci: Add support for Realtek RTS5250 controllers
   - sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
   - sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
   - sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"

* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
  mmc: sdhci-acpi: Intel SDIO has broken card detect
  mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
  mmc: sdhci-msm: Add platform_execute_tuning implementation
  mmc: sdhci-msm: Initial support for Qualcomm chipsets
  mmc: sdhci-msm: Qualcomm SDHCI binding documentation
  sdhci: only reprogram retuning timer when flag is set
  mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
  mmc: sdhci: Allow for irq being shared
  mmc: sdhci-acpi: Add device id 80860F16
  mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
  mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
  mmc: slot-gpio: Split out CD IRQ request into a separate function
  mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
  Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
  mmc: sdhci-spear: use generic card detection gpio support
  mmc: sdhci-spear: remove support for power gpio
  mmc: sdhci-spear: simplify resource handling
  mmc: sdhci-spear: fix platform_data usage
  mmc: sdhci-spear: fix error handling paths for DT
  mmc: sdhci-bcm-kona: fix build errors when built-in
  ...

1 files changed, 115 insertions, 66 deletions

diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index 7b5424f398ac..452782bffebc 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -415,8 +415,7 @@ static int ioctl_do_sanitize(struct mmc_card *card)
 {
 	int err;
 
-	if (!(mmc_can_sanitize(card) &&
-	      (card->host->caps2 & MMC_CAP2_SANITIZE))) {
+	if (!mmc_can_sanitize(card)) {
 			pr_warn("%s: %s - SANITIZE is not supported\n",
 				mmc_hostname(card->host), __func__);
 			err = -EOPNOTSUPP;
@@ -722,19 +721,6 @@ static u32 mmc_sd_num_wr_blocks(struct mmc_card *card)
 	return result;
 }
 
-static int send_stop(struct mmc_card *card, u32 *status)
-{
-	struct mmc_command cmd = {0};
-	int err;
-
-	cmd.opcode = MMC_STOP_TRANSMISSION;
-	cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
-	err = mmc_wait_for_cmd(card->host, &cmd, 5);
-	if (err == 0)
-		*status = cmd.resp[0];
-	return err;
-}
-
 static int get_card_status(struct mmc_card *card, u32 *status, int retries)
 {
 	struct mmc_command cmd = {0};
@@ -750,6 +736,99 @@ static int get_card_status(struct mmc_card *card, u32 *status, int retries)
 	return err;
 }
 
+static int card_busy_detect(struct mmc_card *card, unsigned int timeout_ms,
+		bool hw_busy_detect, struct request *req, int *gen_err)
+{
+	unsigned long timeout = jiffies + msecs_to_jiffies(timeout_ms);
+	int err = 0;
+	u32 status;
+
+	do {
+		err = get_card_status(card, &status, 5);
+		if (err) {
+			pr_err("%s: error %d requesting status\n",
+			       req->rq_disk->disk_name, err);
+			return err;
+		}
+
+		if (status & R1_ERROR) {
+			pr_err("%s: %s: error sending status cmd, status %#x\n",
+				req->rq_disk->disk_name, __func__, status);
+			*gen_err = 1;
+		}
+
+		/* We may rely on the host hw to handle busy detection.*/
+		if ((card->host->caps & MMC_CAP_WAIT_WHILE_BUSY) &&
+			hw_busy_detect)
+			break;
+
+		/*
+		 * Timeout if the device never becomes ready for data and never
+		 * leaves the program state.
+		 */
+		if (time_after(jiffies, timeout)) {
+			pr_err("%s: Card stuck in programming state! %s %s\n",
+				mmc_hostname(card->host),
+				req->rq_disk->disk_name, __func__);
+			return -ETIMEDOUT;
+		}
+
+		/*
+		 * Some cards mishandle the status bits,
+		 * so make sure to check both the busy
+		 * indication and the card state.
+		 */
+	} while (!(status & R1_READY_FOR_DATA) ||
+		 (R1_CURRENT_STATE(status) == R1_STATE_PRG));
+
+	return err;
+}
+
+static int send_stop(struct mmc_card *card, unsigned int timeout_ms,
+		struct request *req, int *gen_err, u32 *stop_status)
+{
+	struct mmc_host *host = card->host;
+	struct mmc_command cmd = {0};
+	int err;
+	bool use_r1b_resp = rq_data_dir(req) == WRITE;
+
+	/*
+	 * Normally we use R1B responses for WRITE, but in cases where the host
+	 * has specified a max_busy_timeout we need to validate it. A failure
+	 * means we need to prevent the host from doing hw busy detection, which
+	 * is done by converting to a R1 response instead.
+	 */
+	if (host->max_busy_timeout && (timeout_ms > host->max_busy_timeout))
+		use_r1b_resp = false;
+
+	cmd.opcode = MMC_STOP_TRANSMISSION;
+	if (use_r1b_resp) {
+		cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
+		cmd.busy_timeout = timeout_ms;
+	} else {
+		cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
+	}
+
+	err = mmc_wait_for_cmd(host, &cmd, 5);
+	if (err)
+		return err;
+
+	*stop_status = cmd.resp[0];
+
+	/* No need to check card status in case of READ. */
+	if (rq_data_dir(req) == READ)
+		return 0;
+
+	if (!mmc_host_is_spi(host) &&
+		(*stop_status & R1_ERROR)) {
+		pr_err("%s: %s: general error sending stop command, resp %#x\n",
+			req->rq_disk->disk_name, __func__, *stop_status);
+		*gen_err = 1;
+	}
+
+	return card_busy_detect(card, timeout_ms, use_r1b_resp, req, gen_err);
+}
+
 #define ERR_NOMEDIUM	3
 #define ERR_RETRY	2
 #define ERR_ABORT	1
@@ -866,26 +945,21 @@ static int mmc_blk_cmd_recovery(struct mmc_card *card, struct request *req,
 	 */
 	if (R1_CURRENT_STATE(status) == R1_STATE_DATA ||
 	    R1_CURRENT_STATE(status) == R1_STATE_RCV) {
-		err = send_stop(card, &stop_status);
-		if (err)
+		err = send_stop(card,
+			DIV_ROUND_UP(brq->data.timeout_ns, 1000000),
+			req, gen_err, &stop_status);
+		if (err) {
 			pr_err("%s: error %d sending stop command\n",
 			       req->rq_disk->disk_name, err);
-
-		/*
-		 * If the stop cmd also timed out, the card is probably
-		 * not present, so abort.  Other errors are bad news too.
-		 */
-		if (err)
+			/*
+			 * If the stop cmd also timed out, the card is probably
+			 * not present, so abort. Other errors are bad news too.
+			 */
 			return ERR_ABORT;
+		}
+
 		if (stop_status & R1_CARD_ECC_FAILED)
 			*ecc_err = 1;
-		if (!mmc_host_is_spi(card->host) && rq_data_dir(req) != READ)
-			if (stop_status & R1_ERROR) {
-				pr_err("%s: %s: general error sending stop command, stop cmd response %#x\n",
-				       req->rq_disk->disk_name, __func__,
-				       stop_status);
-				*gen_err = 1;
-			}
 	}
 
 	/* Check for set block count errors */
@@ -1157,8 +1231,7 @@ static int mmc_blk_err_check(struct mmc_card *card,
 	 * program mode, which we have to wait for it to complete.
 	 */
 	if (!mmc_host_is_spi(card->host) && rq_data_dir(req) != READ) {
-		u32 status;
-		unsigned long timeout;
+		int err;
 
 		/* Check stop command response */
 		if (brq->stop.resp[0] & R1_ERROR) {
@@ -1168,39 +1241,10 @@ static int mmc_blk_err_check(struct mmc_card *card,
 			gen_err = 1;
 		}
 
-		timeout = jiffies + msecs_to_jiffies(MMC_BLK_TIMEOUT_MS);
-		do {
-			int err = get_card_status(card, &status, 5);
-			if (err) {
-				pr_err("%s: error %d requesting status\n",
-				       req->rq_disk->disk_name, err);
-				return MMC_BLK_CMD_ERR;
-			}
-
-			if (status & R1_ERROR) {
-				pr_err("%s: %s: general error sending status command, card status %#x\n",
-				       req->rq_disk->disk_name, __func__,
-				       status);
-				gen_err = 1;
-			}
-
-			/* Timeout if the device never becomes ready for data
-			 * and never leaves the program state.
-			 */
-			if (time_after(jiffies, timeout)) {
-				pr_err("%s: Card stuck in programming state!"\
-					" %s %s\n", mmc_hostname(card->host),
-					req->rq_disk->disk_name, __func__);
-
-				return MMC_BLK_CMD_ERR;
-			}
-			/*
-			 * Some cards mishandle the status bits,
-			 * so make sure to check both the busy
-			 * indication and the card state.
-			 */
-		} while (!(status & R1_READY_FOR_DATA) ||
-			 (R1_CURRENT_STATE(status) == R1_STATE_PRG));
+		err = card_busy_detect(card, MMC_BLK_TIMEOUT_MS, false, req,
+					&gen_err);
+		if (err)
+			return MMC_BLK_CMD_ERR;
 	}
 
 	/* if general error occurs, retry the write operation. */
@@ -1335,7 +1379,6 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
 	brq->data.blksz = 512;
 	brq->stop.opcode = MMC_STOP_TRANSMISSION;
 	brq->stop.arg = 0;
-	brq->stop.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
 	brq->data.blocks = blk_rq_sectors(req);
 
 	/*
@@ -1378,9 +1421,15 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
 	if (rq_data_dir(req) == READ) {
 		brq->cmd.opcode = readcmd;
 		brq->data.flags |= MMC_DATA_READ;
+		if (brq->mrq.stop)
+			brq->stop.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 |
+					MMC_CMD_AC;
 	} else {
 		brq->cmd.opcode = writecmd;
 		brq->data.flags |= MMC_DATA_WRITE;
+		if (brq->mrq.stop)
+			brq->stop.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B |
+					MMC_CMD_AC;
 	}
 
 	if (do_rel_wr)