Merge commit 'v2.6.29-rc4' into perfcounters/core

Conflicts:
	arch/x86/kernel/setup_percpu.c
	arch/x86/mm/fault.c
	drivers/acpi/processor_idle.c
	kernel/irq/handle.c

9 files changed, 2229 insertions, 15 deletions

diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index dfa585f7feaf..99d4b28d52ed 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -76,6 +76,16 @@ config MMC_OMAP
 
 	  If unsure, say N.
 
+config MMC_OMAP_HS
+	tristate "TI OMAP High Speed Multimedia Card Interface support"
+	depends on ARCH_OMAP2430 || ARCH_OMAP3
+	help
+	  This selects the TI OMAP High Speed Multimedia card Interface.
+	  If you have an OMAP2430 or OMAP3 board with a Multimedia Card slot,
+	  say Y or M here.
+
+	  If unsure, say N.
+
 config MMC_WBSD
 	tristate "Winbond W83L51xD SD/MMC Card Interface support"
 	depends on ISA_DMA_API
@@ -135,6 +145,16 @@ config MMC_IMX
 
 	  If unsure, say N.
 
+config MMC_MXC
+	tristate "Freescale i.MX2/3 Multimedia Card Interface support"
+	depends on ARCH_MXC
+	help
+	  This selects the Freescale i.MX2/3 Multimedia card Interface.
+	  If you have a i.MX platform with a Multimedia Card slot,
+	  say Y or M here.
+
+	  If unsure, say N.
+
 config MMC_TIFM_SD
 	tristate "TI Flash Media MMC/SD Interface support  (EXPERIMENTAL)"
 	depends on EXPERIMENTAL && PCI
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index f4853288bbb1..dedec55861d9 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -9,12 +9,14 @@ endif
 obj-$(CONFIG_MMC_ARMMMCI)	+= mmci.o
 obj-$(CONFIG_MMC_PXA)		+= pxamci.o
 obj-$(CONFIG_MMC_IMX)		+= imxmmc.o
+obj-$(CONFIG_MMC_MXC)		+= mxcmmc.o
 obj-$(CONFIG_MMC_SDHCI)		+= sdhci.o
 obj-$(CONFIG_MMC_SDHCI_PCI)	+= sdhci-pci.o
 obj-$(CONFIG_MMC_RICOH_MMC)	+= ricoh_mmc.o
 obj-$(CONFIG_MMC_WBSD)		+= wbsd.o
 obj-$(CONFIG_MMC_AU1X)		+= au1xmmc.o
 obj-$(CONFIG_MMC_OMAP)		+= omap.o
+obj-$(CONFIG_MMC_OMAP_HS)	+= omap_hsmmc.o
 obj-$(CONFIG_MMC_AT91)		+= at91_mci.o
 obj-$(CONFIG_MMC_ATMELMCI)	+= atmel-mci.o
 obj-$(CONFIG_MMC_TIFM_SD)	+= tifm_sd.o
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 1bcbdd6763ac..2909bbc8ad00 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -430,6 +430,8 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 				clk = 255;
 			host->cclk = host->mclk / (2 * (clk + 1));
 		}
+		if (host->hw_designer == 0x80)
+			clk |= MCI_FCEN; /* Bug fix in ST IP block */
 		clk |= MCI_CLK_ENABLE;
 	}
 
@@ -440,15 +442,27 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	case MMC_POWER_OFF:
 		break;
 	case MMC_POWER_UP:
-		pwr |= MCI_PWR_UP;
-		break;
+		/* The ST version does not have this, fall through to POWER_ON */
+		if (host->hw_designer != 0x80) {
+			pwr |= MCI_PWR_UP;
+			break;
+		}
 	case MMC_POWER_ON:
 		pwr |= MCI_PWR_ON;
 		break;
 	}
 
-	if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
-		pwr |= MCI_ROD;
+	if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
+		if (host->hw_designer != 0x80)
+			pwr |= MCI_ROD;
+		else {
+			/*
+			 * The ST Micro variant use the ROD bit for something
+			 * else and only has OD (Open Drain).
+			 */
+			pwr |= MCI_OD;
+		}
+	}
 
 	writel(clk, host->base + MMCICLOCK);
 
@@ -500,6 +514,12 @@ static int mmci_probe(struct amba_device *dev, void *id)
 	}
 
 	host = mmc_priv(mmc);
+	/* Bits 12 thru 19 is the designer */
+	host->hw_designer = (dev->periphid >> 12) & 0xff;
+	/* Bits 20 thru 23 is the revison */
+	host->hw_revision = (dev->periphid >> 20) & 0xf;
+	DBG(host, "designer ID = 0x%02x\n", host->hw_designer);
+	DBG(host, "revision = 0x%01x\n", host->hw_revision);
 	host->clk = clk_get(&dev->dev, NULL);
 	if (IS_ERR(host->clk)) {
 		ret = PTR_ERR(host->clk);
@@ -693,6 +713,15 @@ static struct amba_id mmci_ids[] = {
 		.id	= 0x00041181,
 		.mask	= 0x000fffff,
 	},
+	/* ST Micro variants */
+	{
+		.id     = 0x00180180,
+		.mask   = 0x00ffffff,
+	},
+	{
+		.id     = 0x00280180,
+		.mask   = 0x00ffffff,
+	},
 	{ 0, 0 },
 };
 
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 0f39c490f022..0441bac1c0ec 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -11,13 +11,23 @@
 #define MCI_PWR_OFF		0x00
 #define MCI_PWR_UP		0x02
 #define MCI_PWR_ON		0x03
+#define MCI_DATA2DIREN		(1 << 2)
+#define MCI_CMDDIREN		(1 << 3)
+#define MCI_DATA0DIREN		(1 << 4)
+#define MCI_DATA31DIREN		(1 << 5)
 #define MCI_OD			(1 << 6)
 #define MCI_ROD			(1 << 7)
+/* The ST Micro version does not have ROD */
+#define MCI_FBCLKEN		(1 << 7)
+#define MCI_DATA74DIREN		(1 << 8)
 
 #define MMCICLOCK		0x004
 #define MCI_CLK_ENABLE		(1 << 8)
 #define MCI_CLK_PWRSAVE		(1 << 9)
 #define MCI_CLK_BYPASS		(1 << 10)
+#define MCI_WIDE_BUS		(1 << 11)
+/* HW flow control on the ST Micro version */
+#define MCI_FCEN		(1 << 13)
 
 #define MMCIARGUMENT		0x008
 #define MMCICOMMAND		0x00c
@@ -26,6 +36,10 @@
 #define MCI_CPSM_INTERRUPT	(1 << 8)
 #define MCI_CPSM_PENDING	(1 << 9)
 #define MCI_CPSM_ENABLE		(1 << 10)
+#define MCI_SDIO_SUSP		(1 << 11)
+#define MCI_ENCMD_COMPL		(1 << 12)
+#define MCI_NIEN		(1 << 13)
+#define MCI_CE_ATACMD		(1 << 14)
 
 #define MMCIRESPCMD		0x010
 #define MMCIRESPONSE0		0x014
@@ -39,6 +53,11 @@
 #define MCI_DPSM_DIRECTION	(1 << 1)
 #define MCI_DPSM_MODE		(1 << 2)
 #define MCI_DPSM_DMAENABLE	(1 << 3)
+#define MCI_DPSM_BLOCKSIZE	(1 << 4)
+#define MCI_DPSM_RWSTART	(1 << 8)
+#define MCI_DPSM_RWSTOP		(1 << 9)
+#define MCI_DPSM_RWMOD		(1 << 10)
+#define MCI_DPSM_SDIOEN		(1 << 11)
 
 #define MMCIDATACNT		0x030
 #define MMCISTATUS		0x034
@@ -63,6 +82,8 @@
 #define MCI_RXFIFOEMPTY		(1 << 19)
 #define MCI_TXDATAAVLBL		(1 << 20)
 #define MCI_RXDATAAVLBL		(1 << 21)
+#define MCI_SDIOIT		(1 << 22)
+#define MCI_CEATAEND		(1 << 23)
 
 #define MMCICLEAR		0x038
 #define MCI_CMDCRCFAILCLR	(1 << 0)
@@ -75,6 +96,8 @@
 #define MCI_CMDSENTCLR		(1 << 7)
 #define MCI_DATAENDCLR		(1 << 8)
 #define MCI_DATABLOCKENDCLR	(1 << 10)
+#define MCI_SDIOITC		(1 << 22)
+#define MCI_CEATAENDC		(1 << 23)
 
 #define MMCIMASK0		0x03c
 #define MCI_CMDCRCFAILMASK	(1 << 0)
@@ -98,6 +121,8 @@
 #define MCI_RXFIFOEMPTYMASK	(1 << 19)
 #define MCI_TXDATAAVLBLMASK	(1 << 20)
 #define MCI_RXDATAAVLBLMASK	(1 << 21)
+#define MCI_SDIOITMASK		(1 << 22)
+#define MCI_CEATAENDMASK	(1 << 23)
 
 #define MMCIMASK1		0x040
 #define MMCIFIFOCNT		0x048
@@ -136,6 +161,9 @@ struct mmci_host {
 	u32			pwr;
 	struct mmc_platform_data *plat;
 
+	u8			hw_designer;
+	u8			hw_revision:4;
+
 	struct timer_list	timer;
 	unsigned int		oldstat;
 
diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c
new file mode 100644
index 000000000000..dda0be4e25dc
--- /dev/null
+++ b/drivers/mmc/host/mxcmmc.c
@@ -0,0 +1,880 @@
+/*
+ *  linux/drivers/mmc/host/mxcmmc.c - Freescale i.MX MMCI driver
+ *
+ *  This is a driver for the SDHC controller found in Freescale MX2/MX3
+ *  SoCs. It is basically the same hardware as found on MX1 (imxmmc.c).
+ *  Unlike the hardware found on MX1, this hardware just works and does
+ *  not need all the quirks found in imxmmc.c, hence the seperate driver.
+ *
+ *  Copyright (C) 2008 Sascha Hauer, Pengutronix <s.hauer@pengutronix.de>
+ *  Copyright (C) 2006 Pavel Pisa, PiKRON <ppisa@pikron.com>
+ *
+ *  derived from pxamci.c by Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/blkdev.h>
+#include <linux/dma-mapping.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+
+#include <asm/dma.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+#include <mach/mmc.h>
+
+#ifdef CONFIG_ARCH_MX2
+#include <mach/dma-mx1-mx2.h>
+#define HAS_DMA
+#endif
+
+#define DRIVER_NAME "imx-mmc"
+
+#define MMC_REG_STR_STP_CLK		0x00
+#define MMC_REG_STATUS			0x04
+#define MMC_REG_CLK_RATE		0x08
+#define MMC_REG_CMD_DAT_CONT		0x0C
+#define MMC_REG_RES_TO			0x10
+#define MMC_REG_READ_TO			0x14
+#define MMC_REG_BLK_LEN			0x18
+#define MMC_REG_NOB			0x1C
+#define MMC_REG_REV_NO			0x20
+#define MMC_REG_INT_CNTR		0x24
+#define MMC_REG_CMD			0x28
+#define MMC_REG_ARG			0x2C
+#define MMC_REG_RES_FIFO		0x34
+#define MMC_REG_BUFFER_ACCESS		0x38
+
+#define STR_STP_CLK_RESET               (1 << 3)
+#define STR_STP_CLK_START_CLK           (1 << 1)
+#define STR_STP_CLK_STOP_CLK            (1 << 0)
+
+#define STATUS_CARD_INSERTION		(1 << 31)
+#define STATUS_CARD_REMOVAL		(1 << 30)
+#define STATUS_YBUF_EMPTY		(1 << 29)
+#define STATUS_XBUF_EMPTY		(1 << 28)
+#define STATUS_YBUF_FULL		(1 << 27)
+#define STATUS_XBUF_FULL		(1 << 26)
+#define STATUS_BUF_UND_RUN		(1 << 25)
+#define STATUS_BUF_OVFL			(1 << 24)
+#define STATUS_SDIO_INT_ACTIVE		(1 << 14)
+#define STATUS_END_CMD_RESP		(1 << 13)
+#define STATUS_WRITE_OP_DONE		(1 << 12)
+#define STATUS_DATA_TRANS_DONE		(1 << 11)
+#define STATUS_READ_OP_DONE		(1 << 11)
+#define STATUS_WR_CRC_ERROR_CODE_MASK	(3 << 10)
+#define STATUS_CARD_BUS_CLK_RUN		(1 << 8)
+#define STATUS_BUF_READ_RDY		(1 << 7)
+#define STATUS_BUF_WRITE_RDY		(1 << 6)
+#define STATUS_RESP_CRC_ERR		(1 << 5)
+#define STATUS_CRC_READ_ERR		(1 << 3)
+#define STATUS_CRC_WRITE_ERR		(1 << 2)
+#define STATUS_TIME_OUT_RESP		(1 << 1)
+#define STATUS_TIME_OUT_READ		(1 << 0)
+#define STATUS_ERR_MASK			0x2f
+
+#define CMD_DAT_CONT_CMD_RESP_LONG_OFF	(1 << 12)
+#define CMD_DAT_CONT_STOP_READWAIT	(1 << 11)
+#define CMD_DAT_CONT_START_READWAIT	(1 << 10)
+#define CMD_DAT_CONT_BUS_WIDTH_4	(2 << 8)
+#define CMD_DAT_CONT_INIT		(1 << 7)
+#define CMD_DAT_CONT_WRITE		(1 << 4)
+#define CMD_DAT_CONT_DATA_ENABLE	(1 << 3)
+#define CMD_DAT_CONT_RESPONSE_48BIT_CRC	(1 << 0)
+#define CMD_DAT_CONT_RESPONSE_136BIT	(2 << 0)
+#define CMD_DAT_CONT_RESPONSE_48BIT	(3 << 0)
+
+#define INT_SDIO_INT_WKP_EN		(1 << 18)
+#define INT_CARD_INSERTION_WKP_EN	(1 << 17)
+#define INT_CARD_REMOVAL_WKP_EN		(1 << 16)
+#define INT_CARD_INSERTION_EN		(1 << 15)
+#define INT_CARD_REMOVAL_EN		(1 << 14)
+#define INT_SDIO_IRQ_EN			(1 << 13)
+#define INT_DAT0_EN			(1 << 12)
+#define INT_BUF_READ_EN			(1 << 4)
+#define INT_BUF_WRITE_EN		(1 << 3)
+#define INT_END_CMD_RES_EN		(1 << 2)
+#define INT_WRITE_OP_DONE_EN		(1 << 1)
+#define INT_READ_OP_EN			(1 << 0)
+
+struct mxcmci_host {
+	struct mmc_host		*mmc;
+	struct resource		*res;
+	void __iomem		*base;
+	int			irq;
+	int			detect_irq;
+	int			dma;
+	int			do_dma;
+	unsigned int		power_mode;
+	struct imxmmc_platform_data *pdata;
+
+	struct mmc_request	*req;
+	struct mmc_command	*cmd;
+	struct mmc_data		*data;
+
+	unsigned int		dma_nents;
+	unsigned int		datasize;
+	unsigned int		dma_dir;
+
+	u16			rev_no;
+	unsigned int		cmdat;
+
+	struct clk		*clk;
+
+	int			clock;
+
+	struct work_struct	datawork;
+};
+
+static inline int mxcmci_use_dma(struct mxcmci_host *host)
+{
+	return host->do_dma;
+}
+
+static void mxcmci_softreset(struct mxcmci_host *host)
+{
+	int i;
+
+	/* reset sequence */
+	writew(STR_STP_CLK_RESET, host->base + MMC_REG_STR_STP_CLK);
+	writew(STR_STP_CLK_RESET | STR_STP_CLK_START_CLK,
+			host->base + MMC_REG_STR_STP_CLK);
+
+	for (i = 0; i < 8; i++)
+		writew(STR_STP_CLK_START_CLK, host->base + MMC_REG_STR_STP_CLK);
+
+	writew(0xff, host->base + MMC_REG_RES_TO);
+}
+
+static void mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
+{
+	unsigned int nob = data->blocks;
+	unsigned int blksz = data->blksz;
+	unsigned int datasize = nob * blksz;
+#ifdef HAS_DMA
+	struct scatterlist *sg;
+	int i;
+#endif
+	if (data->flags & MMC_DATA_STREAM)
+		nob = 0xffff;
+
+	host->data = data;
+	data->bytes_xfered = 0;
+
+	writew(nob, host->base + MMC_REG_NOB);
+	writew(blksz, host->base + MMC_REG_BLK_LEN);
+	host->datasize = datasize;
+
+#ifdef HAS_DMA
+	for_each_sg(data->sg, sg, data->sg_len, i) {
+		if (sg->offset & 3 || sg->length & 3) {
+			host->do_dma = 0;
+			return;
+		}
+	}
+
+	if (data->flags & MMC_DATA_READ) {
+		host->dma_dir = DMA_FROM_DEVICE;
+		host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg,
+					     data->sg_len,  host->dma_dir);
+
+		imx_dma_setup_sg(host->dma, data->sg, host->dma_nents, datasize,
+				 host->res->start + MMC_REG_BUFFER_ACCESS,
+				 DMA_MODE_READ);
+	} else {
+		host->dma_dir = DMA_TO_DEVICE;
+		host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg,
+					     data->sg_len,  host->dma_dir);
+
+		imx_dma_setup_sg(host->dma, data->sg, host->dma_nents, datasize,
+				 host->res->start + MMC_REG_BUFFER_ACCESS,
+				 DMA_MODE_WRITE);
+	}
+
+	wmb();
+
+	imx_dma_enable(host->dma);
+#endif /* HAS_DMA */
+}
+
+static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_command *cmd,
+		unsigned int cmdat)
+{
+	WARN_ON(host->cmd != NULL);
+	host->cmd = cmd;
+
+	switch (mmc_resp_type(cmd)) {
+	case MMC_RSP_R1: /* short CRC, OPCODE */
+	case MMC_RSP_R1B:/* short CRC, OPCODE, BUSY */
+		cmdat |= CMD_DAT_CONT_RESPONSE_48BIT_CRC;
+		break;
+	case MMC_RSP_R2: /* long 136 bit + CRC */
+		cmdat |= CMD_DAT_CONT_RESPONSE_136BIT;
+		break;
+	case MMC_RSP_R3: /* short */
+		cmdat |= CMD_DAT_CONT_RESPONSE_48BIT;
+		break;
+	case MMC_RSP_NONE:
+		break;
+	default:
+		dev_err(mmc_dev(host->mmc), "unhandled response type 0x%x\n",
+				mmc_resp_type(cmd));
+		cmd->error = -EINVAL;
+		return -EINVAL;
+	}
+
+	if (mxcmci_use_dma(host))
+		writel(INT_READ_OP_EN | INT_WRITE_OP_DONE_EN |
+				INT_END_CMD_RES_EN,
+				host->base + MMC_REG_INT_CNTR);
+	else
+		writel(INT_END_CMD_RES_EN, host->base + MMC_REG_INT_CNTR);
+
+	writew(cmd->opcode, host->base + MMC_REG_CMD);
+	writel(cmd->arg, host->base + MMC_REG_ARG);
+	writew(cmdat, host->base + MMC_REG_CMD_DAT_CONT);
+
+	return 0;
+}
+
+static void mxcmci_finish_request(struct mxcmci_host *host,
+		struct mmc_request *req)
+{
+	writel(0, host->base + MMC_REG_INT_CNTR);
+
+	host->req = NULL;
+	host->cmd = NULL;
+	host->data = NULL;
+
+	mmc_request_done(host->mmc, req);
+}
+
+static int mxcmci_finish_data(struct mxcmci_host *host, unsigned int stat)
+{
+	struct mmc_data *data = host->data;
+	int data_error;
+
+#ifdef HAS_DMA
+	if (mxcmci_use_dma(host)) {
+		imx_dma_disable(host->dma);
+		dma_unmap_sg(mmc_dev(host->mmc), data->sg, host->dma_nents,
+				host->dma_dir);
+	}
+#endif
+
+	if (stat & STATUS_ERR_MASK) {
+		dev_dbg(mmc_dev(host->mmc), "request failed. status: 0x%08x\n",
+				stat);
+		if (stat & STATUS_CRC_READ_ERR) {
+			data->error = -EILSEQ;
+		} else if (stat & STATUS_CRC_WRITE_ERR) {
+			u32 err_code = (stat >> 9) & 0x3;
+			if (err_code == 2) /* No CRC response */
+				data->error = -ETIMEDOUT;
+			else
+				data->error = -EILSEQ;
+		} else if (stat & STATUS_TIME_OUT_READ) {
+			data->error = -ETIMEDOUT;
+		} else {
+			data->error = -EIO;
+		}
+	} else {
+		data->bytes_xfered = host->datasize;
+	}
+
+	data_error = data->error;
+
+	host->data = NULL;
+
+	return data_error;
+}
+
+static void mxcmci_read_response(struct mxcmci_host *host, unsigned int stat)
+{
+	struct mmc_command *cmd = host->cmd;
+	int i;
+	u32 a, b, c;
+
+	if (!cmd)
+		return;
+
+	if (stat & STATUS_TIME_OUT_RESP) {
+		dev_dbg(mmc_dev(host->mmc), "CMD TIMEOUT\n");
+		cmd->error = -ETIMEDOUT;
+	} else if (stat & STATUS_RESP_CRC_ERR && cmd->flags & MMC_RSP_CRC) {
+		dev_dbg(mmc_dev(host->mmc), "cmd crc error\n");
+		cmd->error = -EILSEQ;
+	}
+
+	if (cmd->flags & MMC_RSP_PRESENT) {
+		if (cmd->flags & MMC_RSP_136) {
+			for (i = 0; i < 4; i++) {
+				a = readw(host->base + MMC_REG_RES_FIFO);
+				b = readw(host->base + MMC_REG_RES_FIFO);
+				cmd->resp[i] = a << 16 | b;
+			}
+		} else {
+			a = readw(host->base + MMC_REG_RES_FIFO);
+			b = readw(host->base + MMC_REG_RES_FIFO);
+			c = readw(host->base + MMC_REG_RES_FIFO);
+			cmd->resp[0] = a << 24 | b << 8 | c >> 8;
+		}
+	}
+}
+
+static int mxcmci_poll_status(struct mxcmci_host *host, u32 mask)
+{
+	u32 stat;
+	unsigned long timeout = jiffies + HZ;
+
+	do {
+		stat = readl(host->base + MMC_REG_STATUS);
+		if (stat & STATUS_ERR_MASK)
+			return stat;
+		if (time_after(jiffies, timeout))
+			return STATUS_TIME_OUT_READ;
+		if (stat & mask)
+			return 0;
+		cpu_relax();
+	} while (1);
+}
+
+static int mxcmci_pull(struct mxcmci_host *host, void *_buf, int bytes)
+{
+	unsigned int stat;
+	u32 *buf = _buf;
+
+	while (bytes > 3) {
+		stat = mxcmci_poll_status(host,
+				STATUS_BUF_READ_RDY | STATUS_READ_OP_DONE);
+		if (stat)
+			return stat;
+		*buf++ = readl(host->base + MMC_REG_BUFFER_ACCESS);
+		bytes -= 4;
+	}
+
+	if (bytes) {
+		u8 *b = (u8 *)buf;
+		u32 tmp;
+
+		stat = mxcmci_poll_status(host,
+				STATUS_BUF_READ_RDY | STATUS_READ_OP_DONE);
+		if (stat)
+			return stat;
+		tmp = readl(host->base + MMC_REG_BUFFER_ACCESS);
+		memcpy(b, &tmp, bytes);
+	}
+
+	return 0;
+}
+
+static int mxcmci_push(struct mxcmci_host *host, void *_buf, int bytes)
+{
+	unsigned int stat;
+	u32 *buf = _buf;
+
+	while (bytes > 3) {
+		stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY);
+		if (stat)
+			return stat;
+		writel(*buf++, host->base + MMC_REG_BUFFER_ACCESS);
+		bytes -= 4;
+	}
+
+	if (bytes) {
+		u8 *b = (u8 *)buf;
+		u32 tmp;
+
+		stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY);
+		if (stat)
+			return stat;
+
+		memcpy(&tmp, b, bytes);
+		writel(tmp, host->base + MMC_REG_BUFFER_ACCESS);
+	}
+
+	stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY);
+	if (stat)
+		return stat;
+
+	return 0;
+}
+
+static int mxcmci_transfer_data(struct mxcmci_host *host)
+{
+	struct mmc_data *data = host->req->data;
+	struct scatterlist *sg;
+	int stat, i;
+
+	host->datasize = 0;
+
+	host->data = data;
+	host->datasize = 0;
+
+	if (data->flags & MMC_DATA_READ) {
+		for_each_sg(data->sg, sg, data->sg_len, i) {
+			stat = mxcmci_pull(host, sg_virt(sg), sg->length);
+			if (stat)
+				return stat;
+			host->datasize += sg->length;
+		}
+	} else {
+		for_each_sg(data->sg, sg, data->sg_len, i) {
+			stat = mxcmci_push(host, sg_virt(sg), sg->length);
+			if (stat)
+				return stat;
+			host->datasize += sg->length;
+		}
+		stat = mxcmci_poll_status(host, STATUS_WRITE_OP_DONE);
+		if (stat)
+			return stat;
+	}
+	return 0;
+}
+
+static void mxcmci_datawork(struct work_struct *work)
+{
+	struct mxcmci_host *host = container_of(work, struct mxcmci_host,
+						  datawork);
+	int datastat = mxcmci_transfer_data(host);
+	mxcmci_finish_data(host, datastat);
+
+	if (host->req->stop) {
+		if (mxcmci_start_cmd(host, host->req->stop, 0)) {
+			mxcmci_finish_request(host, host->req);
+			return;
+		}
+	} else {
+		mxcmci_finish_request(host, host->req);
+	}
+}
+
+#ifdef HAS_DMA
+static void mxcmci_data_done(struct mxcmci_host *host, unsigned int stat)
+{
+	struct mmc_data *data = host->data;
+	int data_error;
+
+	if (!data)
+		return;
+
+	data_error = mxcmci_finish_data(host, stat);
+
+	mxcmci_read_response(host, stat);
+	host->cmd = NULL;
+
+	if (host->req->stop) {
+		if (mxcmci_start_cmd(host, host->req->stop, 0)) {
+			mxcmci_finish_request(host, host->req);
+			return;
+		}
+	} else {
+		mxcmci_finish_request(host, host->req);
+	}
+}
+#endif /* HAS_DMA */
+
+static void mxcmci_cmd_done(struct mxcmci_host *host, unsigned int stat)
+{
+	mxcmci_read_response(host, stat);
+	host->cmd = NULL;
+
+	if (!host->data && host->req) {
+		mxcmci_finish_request(host, host->req);
+		return;
+	}
+
+	/* For the DMA case the DMA engine handles the data transfer
+	 * automatically. For non DMA we have to to it ourselves.
+	 * Don't do it in interrupt context though.
+	 */
+	if (!mxcmci_use_dma(host) && host->data)
+		schedule_work(&host->datawork);
+
+}
+
+static irqreturn_t mxcmci_irq(int irq, void *devid)
+{
+	struct mxcmci_host *host = devid;
+	u32 stat;
+
+	stat = readl(host->base + MMC_REG_STATUS);
+	writel(stat, host->base + MMC_REG_STATUS);
+
+	dev_dbg(mmc_dev(host->mmc), "%s: 0x%08x\n", __func__, stat);
+
+	if (stat & STATUS_END_CMD_RESP)
+		mxcmci_cmd_done(host, stat);
+#ifdef HAS_DMA
+	if (mxcmci_use_dma(host) &&
+		  (stat & (STATUS_DATA_TRANS_DONE | STATUS_WRITE_OP_DONE)))
+		mxcmci_data_done(host, stat);
+#endif
+	return IRQ_HANDLED;
+}
+
+static void mxcmci_request(struct mmc_host *mmc, struct mmc_request *req)
+{
+	struct mxcmci_host *host = mmc_priv(mmc);
+	unsigned int cmdat = host->cmdat;
+
+	WARN_ON(host->req != NULL);
+
+	host->req = req;
+	host->cmdat &= ~CMD_DAT_CONT_INIT;
+#ifdef HAS_DMA
+	host->do_dma = 1;
+#endif
+	if (req->data) {
+		mxcmci_setup_data(host, req->data);
+
+		cmdat |= CMD_DAT_CONT_DATA_ENABLE;
+
+		if (req->data->flags & MMC_DATA_WRITE)
+			cmdat |= CMD_DAT_CONT_WRITE;
+	}
+
+	if (mxcmci_start_cmd(host, req->cmd, cmdat))
+		mxcmci_finish_request(host, req);
+}
+
+static void mxcmci_set_clk_rate(struct mxcmci_host *host, unsigned int clk_ios)
+{
+	unsigned int divider;
+	int prescaler = 0;
+	unsigned int clk_in = clk_get_rate(host->clk);
+
+	while (prescaler <= 0x800) {
+		for (divider = 1; divider <= 0xF; divider++) {
+			int x;
+
+			x = (clk_in / (divider + 1));
+
+			if (prescaler)
+				x /= (prescaler * 2);
+
+			if (x <= clk_ios)
+				break;
+		}
+		if (divider < 0x10)
+			break;
+
+		if (prescaler == 0)
+			prescaler = 1;
+		else
+			prescaler <<= 1;
+	}
+
+	writew((prescaler << 4) | divider, host->base + MMC_REG_CLK_RATE);
+
+	dev_dbg(mmc_dev(host->mmc), "scaler: %d divider: %d in: %d out: %d\n",
+			prescaler, divider, clk_in, clk_ios);
+}
+
+static void mxcmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+	struct mxcmci_host *host = mmc_priv(mmc);
+#ifdef HAS_DMA
+	unsigned int blen;
+	/*
+	 * use burstlen of 64 in 4 bit mode (--> reg value  0)
+	 * use burstlen of 16 in 1 bit mode (--> reg value 16)
+	 */
+	if (ios->bus_width == MMC_BUS_WIDTH_4)
+		blen = 0;
+	else
+		blen = 16;
+
+	imx_dma_config_burstlen(host->dma, blen);
+#endif
+	if (ios->bus_width == MMC_BUS_WIDTH_4)
+		host->cmdat |= CMD_DAT_CONT_BUS_WIDTH_4;
+	else
+		host->cmdat &= ~CMD_DAT_CONT_BUS_WIDTH_4;
+
+	if (host->power_mode != ios->power_mode) {
+		if (host->pdata && host->pdata->setpower)
+			host->pdata->setpower(mmc_dev(mmc), ios->vdd);
+		host->power_mode = ios->power_mode;
+		if (ios->power_mode == MMC_POWER_ON)
+			host->cmdat |= CMD_DAT_CONT_INIT;
+	}
+
+	if (ios->clock) {
+		mxcmci_set_clk_rate(host, ios->clock);
+		writew(STR_STP_CLK_START_CLK, host->base + MMC_REG_STR_STP_CLK);
+	} else {
+		writew(STR_STP_CLK_STOP_CLK, host->base + MMC_REG_STR_STP_CLK);
+	}
+
+	host->clock = ios->clock;
+}
+
+static irqreturn_t mxcmci_detect_irq(int irq, void *data)
+{
+	struct mmc_host *mmc = data;
+
+	dev_dbg(mmc_dev(mmc), "%s\n", __func__);
+
+	mmc_detect_change(mmc, msecs_to_jiffies(250));
+	return IRQ_HANDLED;
+}
+
+static int mxcmci_get_ro(struct mmc_host *mmc)
+{
+	struct mxcmci_host *host = mmc_priv(mmc);
+
+	if (host->pdata && host->pdata->get_ro)
+		return !!host->pdata->get_ro(mmc_dev(mmc));
+	/*
+	 * Board doesn't support read only detection; let the mmc core
+	 * decide what to do.
+	 */
+	return -ENOSYS;
+}
+
+
+static const struct mmc_host_ops mxcmci_ops = {
+	.request	= mxcmci_request,
+	.set_ios	= mxcmci_set_ios,
+	.get_ro		= mxcmci_get_ro,
+};
+
+static int mxcmci_probe(struct platform_device *pdev)
+{
+	struct mmc_host *mmc;
+	struct mxcmci_host *host = NULL;
+	struct resource *r;
+	int ret = 0, irq;
+
+	printk(KERN_INFO "i.MX SDHC driver\n");
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	irq = platform_get_irq(pdev, 0);
+	if (!r || irq < 0)
+		return -EINVAL;
+
+	r = request_mem_region(r->start, resource_size(r), pdev->name);
+	if (!r)
+		return -EBUSY;
+
+	mmc = mmc_alloc_host(sizeof(struct mxcmci_host), &pdev->dev);
+	if (!mmc) {
+		ret = -ENOMEM;
+		goto out_release_mem;
+	}
+
+	mmc->ops = &mxcmci_ops;
+	mmc->caps = MMC_CAP_4_BIT_DATA;
+
+	/* MMC core transfer sizes tunable parameters */
+	mmc->max_hw_segs = 64;
+	mmc->max_phys_segs = 64;
+	mmc->max_blk_size = 2048;
+	mmc->max_blk_count = 65535;
+	mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
+	mmc->max_seg_size = mmc->max_seg_size;
+
+	host = mmc_priv(mmc);
+	host->base = ioremap(r->start, resource_size(r));
+	if (!host->base) {
+		ret = -ENOMEM;
+		goto out_free;
+	}
+
+	host->mmc = mmc;
+	host->pdata = pdev->dev.platform_data;
+
+	if (host->pdata && host->pdata->ocr_avail)
+		mmc->ocr_avail = host->pdata->ocr_avail;
+	else
+		mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+
+	host->res = r;
+	host->irq = irq;
+
+	host->clk = clk_get(&pdev->dev, "sdhc_clk");
+	if (IS_ERR(host->clk)) {
+		ret = PTR_ERR(host->clk);
+		goto out_iounmap;
+	}
+	clk_enable(host->clk);
+
+	mxcmci_softreset(host);
+
+	host->rev_no = readw(host->base + MMC_REG_REV_NO);
+	if (host->rev_no != 0x400) {
+		ret = -ENODEV;
+		dev_err(mmc_dev(host->mmc), "wrong rev.no. 0x%08x. aborting.\n",
+			host->rev_no);
+		goto out_clk_put;
+	}
+
+	mmc->f_min = clk_get_rate(host->clk) >> 7;
+	mmc->f_max = clk_get_rate(host->clk) >> 1;
+
+	/* recommended in data sheet */
+	writew(0x2db4, host->base + MMC_REG_READ_TO);
+
+	writel(0, host->base + MMC_REG_INT_CNTR);
+
+#ifdef HAS_DMA
+	host->dma = imx_dma_request_by_prio(DRIVER_NAME, DMA_PRIO_LOW);
+	if (host->dma < 0) {
+		dev_err(mmc_dev(host->mmc), "imx_dma_request_by_prio failed\n");
+		ret = -EBUSY;
+		goto out_clk_put;
+	}
+
+	r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+	if (!r) {
+		ret = -EINVAL;
+		goto out_free_dma;
+	}
+
+	ret = imx_dma_config_channel(host->dma,
+				     IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_FIFO,
+				     IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_LINEAR,
+				     r->start, 0);
+	if (ret) {
+		dev_err(mmc_dev(host->mmc), "failed to config DMA channel\n");
+		goto out_free_dma;
+	}
+#endif
+	INIT_WORK(&host->datawork, mxcmci_datawork);
+
+	ret = request_irq(host->irq, mxcmci_irq, 0, DRIVER_NAME, host);
+	if (ret)
+		goto out_free_dma;
+
+	platform_set_drvdata(pdev, mmc);
+
+	if (host->pdata && host->pdata->init) {
+		ret = host->pdata->init(&pdev->dev, mxcmci_detect_irq,
+				host->mmc);
+		if (ret)
+			goto out_free_irq;
+	}
+
+	mmc_add_host(mmc);
+
+	return 0;
+
+out_free_irq:
+	free_irq(host->irq, host);
+out_free_dma:
+#ifdef HAS_DMA
+	imx_dma_free(host->dma);
+#endif
+out_clk_put:
+	clk_disable(host->clk);
+	clk_put(host->clk);
+out_iounmap:
+	iounmap(host->base);
+out_free:
+	mmc_free_host(mmc);
+out_release_mem:
+	release_mem_region(host->res->start, resource_size(host->res));
+	return ret;
+}
+
+static int mxcmci_remove(struct platform_device *pdev)
+{
+	struct mmc_host *mmc = platform_get_drvdata(pdev);
+	struct mxcmci_host *host = mmc_priv(mmc);
+
+	platform_set_drvdata(pdev, NULL);
+
+	mmc_remove_host(mmc);
+
+	if (host->pdata && host->pdata->exit)
+		host->pdata->exit(&pdev->dev, mmc);
+
+	free_irq(host->irq, host);
+	iounmap(host->base);
+#ifdef HAS_DMA
+	imx_dma_free(host->dma);
+#endif
+	clk_disable(host->clk);
+	clk_put(host->clk);
+
+	release_mem_region(host->res->start, resource_size(host->res));
+	release_resource(host->res);
+
+	mmc_free_host(mmc);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int mxcmci_suspend(struct platform_device *dev, pm_message_t state)
+{
+	struct mmc_host *mmc = platform_get_drvdata(dev);
+	int ret = 0;
+
+	if (mmc)
+		ret = mmc_suspend_host(mmc, state);
+
+	return ret;
+}
+
+static int mxcmci_resume(struct platform_device *dev)
+{
+	struct mmc_host *mmc = platform_get_drvdata(dev);
+	struct mxcmci_host *host;
+	int ret = 0;
+
+	if (mmc) {
+		host = mmc_priv(mmc);
+		ret = mmc_resume_host(mmc);
+	}
+
+	return ret;
+}
+#else
+#define mxcmci_suspend  NULL
+#define mxcmci_resume   NULL
+#endif /* CONFIG_PM */
+
+static struct platform_driver mxcmci_driver = {
+	.probe		= mxcmci_probe,
+	.remove		= mxcmci_remove,
+	.suspend	= mxcmci_suspend,
+	.resume		= mxcmci_resume,
+	.driver		= {
+		.name		= DRIVER_NAME,
+		.owner		= THIS_MODULE,
+	}
+};
+
+static int __init mxcmci_init(void)
+{
+	return platform_driver_register(&mxcmci_driver);
+}
+
+static void __exit mxcmci_exit(void)
+{
+	platform_driver_unregister(&mxcmci_driver);
+}
+
+module_init(mxcmci_init);
+module_exit(mxcmci_exit);
+
+MODULE_DESCRIPTION("i.MX Multimedia Card Interface Driver");
+MODULE_AUTHOR("Sascha Hauer, Pengutronix");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:imx-mmc");
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
new file mode 100644
index 000000000000..db37490f67ec
--- /dev/null
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -0,0 +1,1242 @@
+/*
+ * drivers/mmc/host/omap_hsmmc.c
+ *
+ * Driver for OMAP2430/3430 MMC controller.
+ *
+ * Copyright (C) 2007 Texas Instruments.
+ *
+ * Authors:
+ *	Syed Mohammed Khasim	<x0khasim@ti.com>
+ *	Madhusudhan		<madhu.cr@ti.com>
+ *	Mohit Jalori		<mjalori@ti.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/workqueue.h>
+#include <linux/timer.h>
+#include <linux/clk.h>
+#include <linux/mmc/host.h>
+#include <linux/io.h>
+#include <linux/semaphore.h>
+#include <mach/dma.h>
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/mmc.h>
+#include <mach/cpu.h>
+
+/* OMAP HSMMC Host Controller Registers */
+#define OMAP_HSMMC_SYSCONFIG	0x0010
+#define OMAP_HSMMC_CON		0x002C
+#define OMAP_HSMMC_BLK		0x0104
+#define OMAP_HSMMC_ARG		0x0108
+#define OMAP_HSMMC_CMD		0x010C
+#define OMAP_HSMMC_RSP10	0x0110
+#define OMAP_HSMMC_RSP32	0x0114
+#define OMAP_HSMMC_RSP54	0x0118
+#define OMAP_HSMMC_RSP76	0x011C
+#define OMAP_HSMMC_DATA		0x0120
+#define OMAP_HSMMC_HCTL		0x0128
+#define OMAP_HSMMC_SYSCTL	0x012C
+#define OMAP_HSMMC_STAT		0x0130
+#define OMAP_HSMMC_IE		0x0134
+#define OMAP_HSMMC_ISE		0x0138
+#define OMAP_HSMMC_CAPA		0x0140
+
+#define VS18			(1 << 26)
+#define VS30			(1 << 25)
+#define SDVS18			(0x5 << 9)
+#define SDVS30			(0x6 << 9)
+#define SDVSCLR			0xFFFFF1FF
+#define SDVSDET			0x00000400
+#define AUTOIDLE		0x1
+#define SDBP			(1 << 8)
+#define DTO			0xe
+#define ICE			0x1
+#define ICS			0x2
+#define CEN			(1 << 2)
+#define CLKD_MASK		0x0000FFC0
+#define CLKD_SHIFT		6
+#define DTO_MASK		0x000F0000
+#define DTO_SHIFT		16
+#define INT_EN_MASK		0x307F0033
+#define INIT_STREAM		(1 << 1)
+#define DP_SELECT		(1 << 21)
+#define DDIR			(1 << 4)
+#define DMA_EN			0x1
+#define MSBS			(1 << 5)
+#define BCE			(1 << 1)
+#define FOUR_BIT		(1 << 1)
+#define CC			0x1
+#define TC			0x02
+#define OD			0x1
+#define ERR			(1 << 15)
+#define CMD_TIMEOUT		(1 << 16)
+#define DATA_TIMEOUT		(1 << 20)
+#define CMD_CRC			(1 << 17)
+#define DATA_CRC		(1 << 21)
+#define CARD_ERR		(1 << 28)
+#define STAT_CLEAR		0xFFFFFFFF
+#define INIT_STREAM_CMD		0x00000000
+#define DUAL_VOLT_OCR_BIT	7
+#define SRC			(1 << 25)
+#define SRD			(1 << 26)
+
+/*
+ * FIXME: Most likely all the data using these _DEVID defines should come
+ * from the platform_data, or implemented in controller and slot specific
+ * functions.
+ */
+#define OMAP_MMC1_DEVID		0
+#define OMAP_MMC2_DEVID		1
+
+#define OMAP_MMC_DATADIR_NONE	0
+#define OMAP_MMC_DATADIR_READ	1
+#define OMAP_MMC_DATADIR_WRITE	2
+#define MMC_TIMEOUT_MS		20
+#define OMAP_MMC_MASTER_CLOCK	96000000
+#define DRIVER_NAME		"mmci-omap-hs"
+
+/*
+ * One controller can have multiple slots, like on some omap boards using
+ * omap.c controller driver. Luckily this is not currently done on any known
+ * omap_hsmmc.c device.
+ */
+#define mmc_slot(host)		(host->pdata->slots[host->slot_id])
+
+/*
+ * MMC Host controller read/write API's
+ */
+#define OMAP_HSMMC_READ(base, reg)	\
+	__raw_readl((base) + OMAP_HSMMC_##reg)
+
+#define OMAP_HSMMC_WRITE(base, reg, val) \
+	__raw_writel((val), (base) + OMAP_HSMMC_##reg)
+
+struct mmc_omap_host {
+	struct	device		*dev;
+	struct	mmc_host	*mmc;
+	struct	mmc_request	*mrq;
+	struct	mmc_command	*cmd;
+	struct	mmc_data	*data;
+	struct	clk		*fclk;
+	struct	clk		*iclk;
+	struct	clk		*dbclk;
+	struct	semaphore	sem;
+	struct	work_struct	mmc_carddetect_work;
+	void	__iomem		*base;
+	resource_size_t		mapbase;
+	unsigned int		id;
+	unsigned int		dma_len;
+	unsigned int		dma_dir;
+	unsigned char		bus_mode;
+	unsigned char		datadir;
+	u32			*buffer;
+	u32			bytesleft;
+	int			suspended;
+	int			irq;
+	int			carddetect;
+	int			use_dma, dma_ch;
+	int			initstr;
+	int			slot_id;
+	int			dbclk_enabled;
+	struct	omap_mmc_platform_data	*pdata;
+};
+
+/*
+ * Stop clock to the card
+ */
+static void omap_mmc_stop_clock(struct mmc_omap_host *host)
+{
+	OMAP_HSMMC_WRITE(host->base, SYSCTL,
+		OMAP_HSMMC_READ(host->base, SYSCTL) & ~CEN);
+	if ((OMAP_HSMMC_READ(host->base, SYSCTL) & CEN) != 0x0)
+		dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stoped\n");
+}
+
+/*
+ * Send init stream sequence to card
+ * before sending IDLE command
+ */
+static void send_init_stream(struct mmc_omap_host *host)
+{
+	int reg = 0;
+	unsigned long timeout;
+
+	disable_irq(host->irq);
+	OMAP_HSMMC_WRITE(host->base, CON,
+		OMAP_HSMMC_READ(host->base, CON) | INIT_STREAM);
+	OMAP_HSMMC_WRITE(host->base, CMD, INIT_STREAM_CMD);
+
+	timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
+	while ((reg != CC) && time_before(jiffies, timeout))
+		reg = OMAP_HSMMC_READ(host->base, STAT) & CC;
+
+	OMAP_HSMMC_WRITE(host->base, CON,
+		OMAP_HSMMC_READ(host->base, CON) & ~INIT_STREAM);
+	enable_irq(host->irq);
+}
+
+static inline
+int mmc_omap_cover_is_closed(struct mmc_omap_host *host)
+{
+	int r = 1;
+
+	if (host->pdata->slots[host->slot_id].get_cover_state)
+		r = host->pdata->slots[host->slot_id].get_cover_state(host->dev,
+			host->slot_id);
+	return r;
+}
+
+static ssize_t
+mmc_omap_show_cover_switch(struct device *dev, struct device_attribute *attr,
+			   char *buf)
+{
+	struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
+	struct mmc_omap_host *host = mmc_priv(mmc);
+
+	return sprintf(buf, "%s\n", mmc_omap_cover_is_closed(host) ? "closed" :
+		       "open");
+}
+
+static DEVICE_ATTR(cover_switch, S_IRUGO, mmc_omap_show_cover_switch, NULL);
+
+static ssize_t
+mmc_omap_show_slot_name(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
+	struct mmc_omap_host *host = mmc_priv(mmc);
+	struct omap_mmc_slot_data slot = host->pdata->slots[host->slot_id];
+
+	return sprintf(buf, "slot:%s\n", slot.name);
+}
+
+static DEVICE_ATTR(slot_name, S_IRUGO, mmc_omap_show_slot_name, NULL);
+
+/*
+ * Configure the response type and send the cmd.
+ */
+static void
+mmc_omap_start_command(struct mmc_omap_host *host, struct mmc_command *cmd,
+	struct mmc_data *data)
+{
+	int cmdreg = 0, resptype = 0, cmdtype = 0;
+
+	dev_dbg(mmc_dev(host->mmc), "%s: CMD%d, argument 0x%08x\n",
+		mmc_hostname(host->mmc), cmd->opcode, cmd->arg);
+	host->cmd = cmd;
+
+	/*
+	 * Clear status bits and enable interrupts
+	 */
+	OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
+	OMAP_HSMMC_WRITE(host->base, ISE, INT_EN_MASK);
+	OMAP_HSMMC_WRITE(host->base, IE, INT_EN_MASK);
+
+	if (cmd->flags & MMC_RSP_PRESENT) {
+		if (cmd->flags & MMC_RSP_136)
+			resptype = 1;
+		else
+			resptype = 2;
+	}
+
+	/*
+	 * Unlike OMAP1 controller, the cmdtype does not seem to be based on
+	 * ac, bc, adtc, bcr. Only commands ending an open ended transfer need
+	 * a val of 0x3, rest 0x0.
+	 */
+	if (cmd == host->mrq->stop)
+		cmdtype = 0x3;
+
+	cmdreg = (cmd->opcode << 24) | (resptype << 16) | (cmdtype << 22);
+
+	if (data) {
+		cmdreg |= DP_SELECT | MSBS | BCE;
+		if (data->flags & MMC_DATA_READ)
+			cmdreg |= DDIR;
+		else
+			cmdreg &= ~(DDIR);
+	}
+
+	if (host->use_dma)
+		cmdreg |= DMA_EN;
+
+	OMAP_HSMMC_WRITE(host->base, ARG, cmd->arg);
+	OMAP_HSMMC_WRITE(host->base, CMD, cmdreg);
+}
+
+/*
+ * Notify the transfer complete to MMC core
+ */
+static void
+mmc_omap_xfer_done(struct mmc_omap_host *host, struct mmc_data *data)
+{
+	host->data = NULL;
+
+	if (host->use_dma && host->dma_ch != -1)
+		dma_unmap_sg(mmc_dev(host->mmc), data->sg, host->dma_len,
+			host->dma_dir);
+
+	host->datadir = OMAP_MMC_DATADIR_NONE;
+
+	if (!data->error)
+		data->bytes_xfered += data->blocks * (data->blksz);
+	else
+		data->bytes_xfered = 0;
+
+	if (!data->stop) {
+		host->mrq = NULL;
+		mmc_request_done(host->mmc, data->mrq);
+		return;
+	}
+	mmc_omap_start_command(host, data->stop, NULL);
+}
+
+/*
+ * Notify the core about command completion
+ */
+static void
+mmc_omap_cmd_done(struct mmc_omap_host *host, struct mmc_command *cmd)
+{
+	host->cmd = NULL;
+
+	if (cmd->flags & MMC_RSP_PRESENT) {
+		if (cmd->flags & MMC_RSP_136) {
+			/* response type 2 */
+			cmd->resp[3] = OMAP_HSMMC_READ(host->base, RSP10);
+			cmd->resp[2] = OMAP_HSMMC_READ(host->base, RSP32);
+			cmd->resp[1] = OMAP_HSMMC_READ(host->base, RSP54);
+			cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP76);
+		} else {
+			/* response types 1, 1b, 3, 4, 5, 6 */
+			cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP10);
+		}
+	}
+	if (host->data == NULL || cmd->error) {
+		host->mrq = NULL;
+		mmc_request_done(host->mmc, cmd->mrq);
+	}
+}
+
+/*
+ * DMA clean up for command errors
+ */
+static void mmc_dma_cleanup(struct mmc_omap_host *host)
+{
+	host->data->error = -ETIMEDOUT;
+
+	if (host->use_dma && host->dma_ch != -1) {
+		dma_unmap_sg(mmc_dev(host->mmc), host->data->sg, host->dma_len,
+			host->dma_dir);
+		omap_free_dma(host->dma_ch);
+		host->dma_ch = -1;
+		up(&host->sem);
+	}
+	host->data = NULL;
+	host->datadir = OMAP_MMC_DATADIR_NONE;
+}
+
+/*
+ * Readable error output
+ */
+#ifdef CONFIG_MMC_DEBUG
+static void mmc_omap_report_irq(struct mmc_omap_host *host, u32 status)
+{
+	/* --- means reserved bit without definition at documentation */
+	static const char *mmc_omap_status_bits[] = {
+		"CC", "TC", "BGE", "---", "BWR", "BRR", "---", "---", "CIRQ",
+		"OBI", "---", "---", "---", "---", "---", "ERRI", "CTO", "CCRC",
+		"CEB", "CIE", "DTO", "DCRC", "DEB", "---", "ACE", "---",
+		"---", "---", "---", "CERR", "CERR", "BADA", "---", "---", "---"
+	};
+	char res[256];
+	char *buf = res;
+	int len, i;
+
+	len = sprintf(buf, "MMC IRQ 0x%x :", status);
+	buf += len;
+
+	for (i = 0; i < ARRAY_SIZE(mmc_omap_status_bits); i++)
+		if (status & (1 << i)) {
+			len = sprintf(buf, " %s", mmc_omap_status_bits[i]);
+			buf += len;
+		}
+
+	dev_dbg(mmc_dev(host->mmc), "%s\n", res);
+}
+#endif  /* CONFIG_MMC_DEBUG */
+
+
+/*
+ * MMC controller IRQ handler
+ */
+static irqreturn_t mmc_omap_irq(int irq, void *dev_id)
+{
+	struct mmc_omap_host *host = dev_id;
+	struct mmc_data *data;
+	int end_cmd = 0, end_trans = 0, status;
+
+	if (host->cmd == NULL && host->data == NULL) {
+		OMAP_HSMMC_WRITE(host->base, STAT,
+			OMAP_HSMMC_READ(host->base, STAT));
+		return IRQ_HANDLED;
+	}
+
+	data = host->data;
+	status = OMAP_HSMMC_READ(host->base, STAT);
+	dev_dbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status);
+
+	if (status & ERR) {
+#ifdef CONFIG_MMC_DEBUG
+		mmc_omap_report_irq(host, status);
+#endif
+		if ((status & CMD_TIMEOUT) ||
+			(status & CMD_CRC)) {
+			if (host->cmd) {
+				if (status & CMD_TIMEOUT) {
+					OMAP_HSMMC_WRITE(host->base, SYSCTL,
+						OMAP_HSMMC_READ(host->base,
+								SYSCTL) | SRC);
+					while (OMAP_HSMMC_READ(host->base,
+							SYSCTL) & SRC)
+						;
+
+					host->cmd->error = -ETIMEDOUT;
+				} else {
+					host->cmd->error = -EILSEQ;
+				}
+				end_cmd = 1;
+			}
+			if (host->data)
+				mmc_dma_cleanup(host);
+		}
+		if ((status & DATA_TIMEOUT) ||
+			(status & DATA_CRC)) {
+			if (host->data) {
+				if (status & DATA_TIMEOUT)
+					mmc_dma_cleanup(host);
+				else
+					host->data->error = -EILSEQ;
+				OMAP_HSMMC_WRITE(host->base, SYSCTL,
+					OMAP_HSMMC_READ(host->base,
+							SYSCTL) | SRD);
+				while (OMAP_HSMMC_READ(host->base,
+						SYSCTL) & SRD)
+					;
+				end_trans = 1;
+			}
+		}
+		if (status & CARD_ERR) {
+			dev_dbg(mmc_dev(host->mmc),
+				"Ignoring card err CMD%d\n", host->cmd->opcode);
+			if (host->cmd)
+				end_cmd = 1;
+			if (host->data)
+				end_trans = 1;
+		}
+	}
+
+	OMAP_HSMMC_WRITE(host->base, STAT, status);
+
+	if (end_cmd || (status & CC))
+		mmc_omap_cmd_done(host, host->cmd);
+	if (end_trans || (status & TC))
+		mmc_omap_xfer_done(host, data);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Switch MMC operating voltage
+ */
+static int omap_mmc_switch_opcond(struct mmc_omap_host *host, int vdd)
+{
+	u32 reg_val = 0;
+	int ret;
+
+	/* Disable the clocks */
+	clk_disable(host->fclk);
+	clk_disable(host->iclk);
+	clk_disable(host->dbclk);
+
+	/* Turn the power off */
+	ret = mmc_slot(host).set_power(host->dev, host->slot_id, 0, 0);
+	if (ret != 0)
+		goto err;
+
+	/* Turn the power ON with given VDD 1.8 or 3.0v */
+	ret = mmc_slot(host).set_power(host->dev, host->slot_id, 1, vdd);
+	if (ret != 0)
+		goto err;
+
+	clk_enable(host->fclk);
+	clk_enable(host->iclk);
+	clk_enable(host->dbclk);
+
+	OMAP_HSMMC_WRITE(host->base, HCTL,
+		OMAP_HSMMC_READ(host->base, HCTL) & SDVSCLR);
+	reg_val = OMAP_HSMMC_READ(host->base, HCTL);
+	/*
+	 * If a MMC dual voltage card is detected, the set_ios fn calls
+	 * this fn with VDD bit set for 1.8V. Upon card removal from the
+	 * slot, omap_mmc_set_ios sets the VDD back to 3V on MMC_POWER_OFF.
+	 *
+	 * Only MMC1 supports 3.0V.  MMC2 will not function if SDVS30 is
+	 * set in HCTL.
+	 */
+	if (host->id == OMAP_MMC1_DEVID && (((1 << vdd) == MMC_VDD_32_33) ||
+				((1 << vdd) == MMC_VDD_33_34)))
+		reg_val |= SDVS30;
+	if ((1 << vdd) == MMC_VDD_165_195)
+		reg_val |= SDVS18;
+
+	OMAP_HSMMC_WRITE(host->base, HCTL, reg_val);
+
+	OMAP_HSMMC_WRITE(host->base, HCTL,
+		OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
+
+	return 0;
+err:
+	dev_dbg(mmc_dev(host->mmc), "Unable to switch operating voltage\n");
+	return ret;
+}
+
+/*
+ * Work Item to notify the core about card insertion/removal
+ */
+static void mmc_omap_detect(struct work_struct *work)
+{
+	struct mmc_omap_host *host = container_of(work, struct mmc_omap_host,
+						mmc_carddetect_work);
+
+	sysfs_notify(&host->mmc->class_dev.kobj, NULL, "cover_switch");
+	if (host->carddetect) {
+		mmc_detect_change(host->mmc, (HZ * 200) / 1000);
+	} else {
+		OMAP_HSMMC_WRITE(host->base, SYSCTL,
+			OMAP_HSMMC_READ(host->base, SYSCTL) | SRD);
+		while (OMAP_HSMMC_READ(host->base, SYSCTL) & SRD)
+			;
+
+		mmc_detect_change(host->mmc, (HZ * 50) / 1000);
+	}
+}
+
+/*
+ * ISR for handling card insertion and removal
+ */
+static irqreturn_t omap_mmc_cd_handler(int irq, void *dev_id)
+{
+	struct mmc_omap_host *host = (struct mmc_omap_host *)dev_id;
+
+	host->carddetect = mmc_slot(host).card_detect(irq);
+	schedule_work(&host->mmc_carddetect_work);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * DMA call back function
+ */
+static void mmc_omap_dma_cb(int lch, u16 ch_status, void *data)
+{
+	struct mmc_omap_host *host = data;
+
+	if (ch_status & OMAP2_DMA_MISALIGNED_ERR_IRQ)
+		dev_dbg(mmc_dev(host->mmc), "MISALIGNED_ADRS_ERR\n");
+
+	if (host->dma_ch < 0)
+		return;
+
+	omap_free_dma(host->dma_ch);
+	host->dma_ch = -1;
+	/*
+	 * DMA Callback: run in interrupt context.
+	 * mutex_unlock will through a kernel warning if used.
+	 */
+	up(&host->sem);
+}
+
+/*
+ * Configure dma src and destination parameters
+ */
+static int mmc_omap_config_dma_param(int sync_dir, struct mmc_omap_host *host,
+				struct mmc_data *data)
+{
+	if (sync_dir == 0) {
+		omap_set_dma_dest_params(host->dma_ch, 0,
+			OMAP_DMA_AMODE_CONSTANT,
+			(host->mapbase + OMAP_HSMMC_DATA), 0, 0);
+		omap_set_dma_src_params(host->dma_ch, 0,
+			OMAP_DMA_AMODE_POST_INC,
+			sg_dma_address(&data->sg[0]), 0, 0);
+	} else {
+		omap_set_dma_src_params(host->dma_ch, 0,
+			OMAP_DMA_AMODE_CONSTANT,
+			(host->mapbase + OMAP_HSMMC_DATA), 0, 0);
+		omap_set_dma_dest_params(host->dma_ch, 0,
+			OMAP_DMA_AMODE_POST_INC,
+			sg_dma_address(&data->sg[0]), 0, 0);
+	}
+	return 0;
+}
+/*
+ * Routine to configure and start DMA for the MMC card
+ */
+static int
+mmc_omap_start_dma_transfer(struct mmc_omap_host *host, struct mmc_request *req)
+{
+	int sync_dev, sync_dir = 0;
+	int dma_ch = 0, ret = 0, err = 1;
+	struct mmc_data *data = req->data;
+
+	/*
+	 * If for some reason the DMA transfer is still active,
+	 * we wait for timeout period and free the dma
+	 */
+	if (host->dma_ch != -1) {
+		set_current_state(TASK_UNINTERRUPTIBLE);
+		schedule_timeout(100);
+		if (down_trylock(&host->sem)) {
+			omap_free_dma(host->dma_ch);
+			host->dma_ch = -1;
+			up(&host->sem);
+			return err;
+		}
+	} else {
+		if (down_trylock(&host->sem))
+			return err;
+	}
+
+	if (!(data->flags & MMC_DATA_WRITE)) {
+		host->dma_dir = DMA_FROM_DEVICE;
+		if (host->id == OMAP_MMC1_DEVID)
+			sync_dev = OMAP24XX_DMA_MMC1_RX;
+		else
+			sync_dev = OMAP24XX_DMA_MMC2_RX;
+	} else {
+		host->dma_dir = DMA_TO_DEVICE;
+		if (host->id == OMAP_MMC1_DEVID)
+			sync_dev = OMAP24XX_DMA_MMC1_TX;
+		else
+			sync_dev = OMAP24XX_DMA_MMC2_TX;
+	}
+
+	ret = omap_request_dma(sync_dev, "MMC/SD", mmc_omap_dma_cb,
+			host, &dma_ch);
+	if (ret != 0) {
+		dev_dbg(mmc_dev(host->mmc),
+			"%s: omap_request_dma() failed with %d\n",
+			mmc_hostname(host->mmc), ret);
+		return ret;
+	}
+
+	host->dma_len = dma_map_sg(mmc_dev(host->mmc), data->sg,
+			data->sg_len, host->dma_dir);
+	host->dma_ch = dma_ch;
+
+	if (!(data->flags & MMC_DATA_WRITE))
+		mmc_omap_config_dma_param(1, host, data);
+	else
+		mmc_omap_config_dma_param(0, host, data);
+
+	if ((data->blksz % 4) == 0)
+		omap_set_dma_transfer_params(dma_ch, OMAP_DMA_DATA_TYPE_S32,
+			(data->blksz / 4), data->blocks, OMAP_DMA_SYNC_FRAME,
+			sync_dev, sync_dir);
+	else
+		/* REVISIT: The MMC buffer increments only when MSB is written.
+		 * Return error for blksz which is non multiple of four.
+		 */
+		return -EINVAL;
+
+	omap_start_dma(dma_ch);
+	return 0;
+}
+
+static void set_data_timeout(struct mmc_omap_host *host,
+			     struct mmc_request *req)
+{
+	unsigned int timeout, cycle_ns;
+	uint32_t reg, clkd, dto = 0;
+
+	reg = OMAP_HSMMC_READ(host->base, SYSCTL);
+	clkd = (reg & CLKD_MASK) >> CLKD_SHIFT;
+	if (clkd == 0)
+		clkd = 1;
+
+	cycle_ns = 1000000000 / (clk_get_rate(host->fclk) / clkd);
+	timeout = req->data->timeout_ns / cycle_ns;
+	timeout += req->data->timeout_clks;
+	if (timeout) {
+		while ((timeout & 0x80000000) == 0) {
+			dto += 1;
+			timeout <<= 1;
+		}
+		dto = 31 - dto;
+		timeout <<= 1;
+		if (timeout && dto)
+			dto += 1;
+		if (dto >= 13)
+			dto -= 13;
+		else
+			dto = 0;
+		if (dto > 14)
+			dto = 14;
+	}
+
+	reg &= ~DTO_MASK;
+	reg |= dto << DTO_SHIFT;
+	OMAP_HSMMC_WRITE(host->base, SYSCTL, reg);
+}
+
+/*
+ * Configure block length for MMC/SD cards and initiate the transfer.
+ */
+static int
+mmc_omap_prepare_data(struct mmc_omap_host *host, struct mmc_request *req)
+{
+	int ret;
+	host->data = req->data;
+
+	if (req->data == NULL) {
+		host->datadir = OMAP_MMC_DATADIR_NONE;
+		OMAP_HSMMC_WRITE(host->base, BLK, 0);
+		return 0;
+	}
+
+	OMAP_HSMMC_WRITE(host->base, BLK, (req->data->blksz)
+					| (req->data->blocks << 16));
+	set_data_timeout(host, req);
+
+	host->datadir = (req->data->flags & MMC_DATA_WRITE) ?
+			OMAP_MMC_DATADIR_WRITE : OMAP_MMC_DATADIR_READ;
+
+	if (host->use_dma) {
+		ret = mmc_omap_start_dma_transfer(host, req);
+		if (ret != 0) {
+			dev_dbg(mmc_dev(host->mmc), "MMC start dma failure\n");
+			return ret;
+		}
+	}
+	return 0;
+}
+
+/*
+ * Request function. for read/write operation
+ */
+static void omap_mmc_request(struct mmc_host *mmc, struct mmc_request *req)
+{
+	struct mmc_omap_host *host = mmc_priv(mmc);
+
+	WARN_ON(host->mrq != NULL);
+	host->mrq = req;
+	mmc_omap_prepare_data(host, req);
+	mmc_omap_start_command(host, req->cmd, req->data);
+}
+
+
+/* Routine to configure clock values. Exposed API to core */
+static void omap_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+	struct mmc_omap_host *host = mmc_priv(mmc);
+	u16 dsor = 0;
+	unsigned long regval;
+	unsigned long timeout;
+
+	switch (ios->power_mode) {
+	case MMC_POWER_OFF:
+		mmc_slot(host).set_power(host->dev, host->slot_id, 0, 0);
+		/*
+		 * Reset bus voltage to 3V if it got set to 1.8V earlier.
+		 * REVISIT: If we are able to detect cards after unplugging
+		 * a 1.8V card, this code should not be needed.
+		 */
+		if (!(OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET)) {
+			int vdd = fls(host->mmc->ocr_avail) - 1;
+			if (omap_mmc_switch_opcond(host, vdd) != 0)
+				host->mmc->ios.vdd = vdd;
+		}
+		break;
+	case MMC_POWER_UP:
+		mmc_slot(host).set_power(host->dev, host->slot_id, 1, ios->vdd);
+		break;
+	}
+
+	switch (mmc->ios.bus_width) {
+	case MMC_BUS_WIDTH_4:
+		OMAP_HSMMC_WRITE(host->base, HCTL,
+			OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT);
+		break;
+	case MMC_BUS_WIDTH_1:
+		OMAP_HSMMC_WRITE(host->base, HCTL,
+			OMAP_HSMMC_READ(host->base, HCTL) & ~FOUR_BIT);
+		break;
+	}
+
+	if (host->id == OMAP_MMC1_DEVID) {
+		/* Only MMC1 can operate at 3V/1.8V */
+		if ((OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET) &&
+			(ios->vdd == DUAL_VOLT_OCR_BIT)) {
+				/*
+				 * The mmc_select_voltage fn of the core does
+				 * not seem to set the power_mode to
+				 * MMC_POWER_UP upon recalculating the voltage.
+				 * vdd 1.8v.
+				 */
+				if (omap_mmc_switch_opcond(host, ios->vdd) != 0)
+					dev_dbg(mmc_dev(host->mmc),
+						"Switch operation failed\n");
+		}
+	}
+
+	if (ios->clock) {
+		dsor = OMAP_MMC_MASTER_CLOCK / ios->clock;
+		if (dsor < 1)
+			dsor = 1;
+
+		if (OMAP_MMC_MASTER_CLOCK / dsor > ios->clock)
+			dsor++;
+
+		if (dsor > 250)
+			dsor = 250;
+	}
+	omap_mmc_stop_clock(host);
+	regval = OMAP_HSMMC_READ(host->base, SYSCTL);
+	regval = regval & ~(CLKD_MASK);
+	regval = regval | (dsor << 6) | (DTO << 16);
+	OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
+	OMAP_HSMMC_WRITE(host->base, SYSCTL,
+		OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
+
+	/* Wait till the ICS bit is set */
+	timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
+	while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != 0x2
+		&& time_before(jiffies, timeout))
+		msleep(1);
+
+	OMAP_HSMMC_WRITE(host->base, SYSCTL,
+		OMAP_HSMMC_READ(host->base, SYSCTL) | CEN);
+
+	if (ios->power_mode == MMC_POWER_ON)
+		send_init_stream(host);
+
+	if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
+		OMAP_HSMMC_WRITE(host->base, CON,
+				OMAP_HSMMC_READ(host->base, CON) | OD);
+}
+
+static int omap_hsmmc_get_cd(struct mmc_host *mmc)
+{
+	struct mmc_omap_host *host = mmc_priv(mmc);
+	struct omap_mmc_platform_data *pdata = host->pdata;
+
+	if (!pdata->slots[0].card_detect)
+		return -ENOSYS;
+	return pdata->slots[0].card_detect(pdata->slots[0].card_detect_irq);
+}
+
+static int omap_hsmmc_get_ro(struct mmc_host *mmc)
+{
+	struct mmc_omap_host *host = mmc_priv(mmc);
+	struct omap_mmc_platform_data *pdata = host->pdata;
+
+	if (!pdata->slots[0].get_ro)
+		return -ENOSYS;
+	return pdata->slots[0].get_ro(host->dev, 0);
+}
+
+static struct mmc_host_ops mmc_omap_ops = {
+	.request = omap_mmc_request,
+	.set_ios = omap_mmc_set_ios,
+	.get_cd = omap_hsmmc_get_cd,
+	.get_ro = omap_hsmmc_get_ro,
+	/* NYET -- enable_sdio_irq */
+};
+
+static int __init omap_mmc_probe(struct platform_device *pdev)
+{
+	struct omap_mmc_platform_data *pdata = pdev->dev.platform_data;
+	struct mmc_host *mmc;
+	struct mmc_omap_host *host = NULL;
+	struct resource *res;
+	int ret = 0, irq;
+	u32 hctl, capa;
+
+	if (pdata == NULL) {
+		dev_err(&pdev->dev, "Platform Data is missing\n");
+		return -ENXIO;
+	}
+
+	if (pdata->nr_slots == 0) {
+		dev_err(&pdev->dev, "No Slots\n");
+		return -ENXIO;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	irq = platform_get_irq(pdev, 0);
+	if (res == NULL || irq < 0)
+		return -ENXIO;
+
+	res = request_mem_region(res->start, res->end - res->start + 1,
+							pdev->name);
+	if (res == NULL)
+		return -EBUSY;
+
+	mmc = mmc_alloc_host(sizeof(struct mmc_omap_host), &pdev->dev);
+	if (!mmc) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	host		= mmc_priv(mmc);
+	host->mmc	= mmc;
+	host->pdata	= pdata;
+	host->dev	= &pdev->dev;
+	host->use_dma	= 1;
+	host->dev->dma_mask = &pdata->dma_mask;
+	host->dma_ch	= -1;
+	host->irq	= irq;
+	host->id	= pdev->id;
+	host->slot_id	= 0;
+	host->mapbase	= res->start;
+	host->base	= ioremap(host->mapbase, SZ_4K);
+
+	platform_set_drvdata(pdev, host);
+	INIT_WORK(&host->mmc_carddetect_work, mmc_omap_detect);
+
+	mmc->ops	= &mmc_omap_ops;
+	mmc->f_min	= 400000;
+	mmc->f_max	= 52000000;
+
+	sema_init(&host->sem, 1);
+
+	host->iclk = clk_get(&pdev->dev, "mmchs_ick");
+	if (IS_ERR(host->iclk)) {
+		ret = PTR_ERR(host->iclk);
+		host->iclk = NULL;
+		goto err1;
+	}
+	host->fclk = clk_get(&pdev->dev, "mmchs_fck");
+	if (IS_ERR(host->fclk)) {
+		ret = PTR_ERR(host->fclk);
+		host->fclk = NULL;
+		clk_put(host->iclk);
+		goto err1;
+	}
+
+	if (clk_enable(host->fclk) != 0) {
+		clk_put(host->iclk);
+		clk_put(host->fclk);
+		goto err1;
+	}
+
+	if (clk_enable(host->iclk) != 0) {
+		clk_disable(host->fclk);
+		clk_put(host->iclk);
+		clk_put(host->fclk);
+		goto err1;
+	}
+
+	host->dbclk = clk_get(&pdev->dev, "mmchsdb_fck");
+	/*
+	 * MMC can still work without debounce clock.
+	 */
+	if (IS_ERR(host->dbclk))
+		dev_warn(mmc_dev(host->mmc), "Failed to get debounce clock\n");
+	else
+		if (clk_enable(host->dbclk) != 0)
+			dev_dbg(mmc_dev(host->mmc), "Enabling debounce"
+							" clk failed\n");
+		else
+			host->dbclk_enabled = 1;
+
+#ifdef CONFIG_MMC_BLOCK_BOUNCE
+	mmc->max_phys_segs = 1;
+	mmc->max_hw_segs = 1;
+#endif
+	mmc->max_blk_size = 512;       /* Block Length at max can be 1024 */
+	mmc->max_blk_count = 0xFFFF;    /* No. of Blocks is 16 bits */
+	mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
+	mmc->max_seg_size = mmc->max_req_size;
+
+	mmc->ocr_avail = mmc_slot(host).ocr_mask;
+	mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED;
+
+	if (pdata->slots[host->slot_id].wires >= 4)
+		mmc->caps |= MMC_CAP_4_BIT_DATA;
+
+	/* Only MMC1 supports 3.0V */
+	if (host->id == OMAP_MMC1_DEVID) {
+		hctl = SDVS30;
+		capa = VS30 | VS18;
+	} else {
+		hctl = SDVS18;
+		capa = VS18;
+	}
+
+	OMAP_HSMMC_WRITE(host->base, HCTL,
+			OMAP_HSMMC_READ(host->base, HCTL) | hctl);
+
+	OMAP_HSMMC_WRITE(host->base, CAPA,
+			OMAP_HSMMC_READ(host->base, CAPA) | capa);
+
+	/* Set the controller to AUTO IDLE mode */
+	OMAP_HSMMC_WRITE(host->base, SYSCONFIG,
+			OMAP_HSMMC_READ(host->base, SYSCONFIG) | AUTOIDLE);
+
+	/* Set SD bus power bit */
+	OMAP_HSMMC_WRITE(host->base, HCTL,
+			OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
+
+	/* Request IRQ for MMC operations */
+	ret = request_irq(host->irq, mmc_omap_irq, IRQF_DISABLED,
+			mmc_hostname(mmc), host);
+	if (ret) {
+		dev_dbg(mmc_dev(host->mmc), "Unable to grab HSMMC IRQ\n");
+		goto err_irq;
+	}
+
+	if (pdata->init != NULL) {
+		if (pdata->init(&pdev->dev) != 0) {
+			dev_dbg(mmc_dev(host->mmc),
+				"Unable to configure MMC IRQs\n");
+			goto err_irq_cd_init;
+		}
+	}
+
+	/* Request IRQ for card detect */
+	if ((mmc_slot(host).card_detect_irq) && (mmc_slot(host).card_detect)) {
+		ret = request_irq(mmc_slot(host).card_detect_irq,
+				  omap_mmc_cd_handler,
+				  IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING
+					  | IRQF_DISABLED,
+				  mmc_hostname(mmc), host);
+		if (ret) {
+			dev_dbg(mmc_dev(host->mmc),
+				"Unable to grab MMC CD IRQ\n");
+			goto err_irq_cd;
+		}
+	}
+
+	OMAP_HSMMC_WRITE(host->base, ISE, INT_EN_MASK);
+	OMAP_HSMMC_WRITE(host->base, IE, INT_EN_MASK);
+
+	mmc_add_host(mmc);
+
+	if (host->pdata->slots[host->slot_id].name != NULL) {
+		ret = device_create_file(&mmc->class_dev, &dev_attr_slot_name);
+		if (ret < 0)
+			goto err_slot_name;
+	}
+	if (mmc_slot(host).card_detect_irq && mmc_slot(host).card_detect &&
+			host->pdata->slots[host->slot_id].get_cover_state) {
+		ret = device_create_file(&mmc->class_dev,
+					&dev_attr_cover_switch);
+		if (ret < 0)
+			goto err_cover_switch;
+	}
+
+	return 0;
+
+err_cover_switch:
+	device_remove_file(&mmc->class_dev, &dev_attr_cover_switch);
+err_slot_name:
+	mmc_remove_host(mmc);
+err_irq_cd:
+	free_irq(mmc_slot(host).card_detect_irq, host);
+err_irq_cd_init:
+	free_irq(host->irq, host);
+err_irq:
+	clk_disable(host->fclk);
+	clk_disable(host->iclk);
+	clk_put(host->fclk);
+	clk_put(host->iclk);
+	if (host->dbclk_enabled) {
+		clk_disable(host->dbclk);
+		clk_put(host->dbclk);
+	}
+
+err1:
+	iounmap(host->base);
+err:
+	dev_dbg(mmc_dev(host->mmc), "Probe Failed\n");
+	release_mem_region(res->start, res->end - res->start + 1);
+	if (host)
+		mmc_free_host(mmc);
+	return ret;
+}
+
+static int omap_mmc_remove(struct platform_device *pdev)
+{
+	struct mmc_omap_host *host = platform_get_drvdata(pdev);
+	struct resource *res;
+
+	if (host) {
+		mmc_remove_host(host->mmc);
+		if (host->pdata->cleanup)
+			host->pdata->cleanup(&pdev->dev);
+		free_irq(host->irq, host);
+		if (mmc_slot(host).card_detect_irq)
+			free_irq(mmc_slot(host).card_detect_irq, host);
+		flush_scheduled_work();
+
+		clk_disable(host->fclk);
+		clk_disable(host->iclk);
+		clk_put(host->fclk);
+		clk_put(host->iclk);
+		if (host->dbclk_enabled) {
+			clk_disable(host->dbclk);
+			clk_put(host->dbclk);
+		}
+
+		mmc_free_host(host->mmc);
+		iounmap(host->base);
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res)
+		release_mem_region(res->start, res->end - res->start + 1);
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int omap_mmc_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	int ret = 0;
+	struct mmc_omap_host *host = platform_get_drvdata(pdev);
+
+	if (host && host->suspended)
+		return 0;
+
+	if (host) {
+		ret = mmc_suspend_host(host->mmc, state);
+		if (ret == 0) {
+			host->suspended = 1;
+
+			OMAP_HSMMC_WRITE(host->base, ISE, 0);
+			OMAP_HSMMC_WRITE(host->base, IE, 0);
+
+			if (host->pdata->suspend) {
+				ret = host->pdata->suspend(&pdev->dev,
+								host->slot_id);
+				if (ret)
+					dev_dbg(mmc_dev(host->mmc),
+						"Unable to handle MMC board"
+						" level suspend\n");
+			}
+
+			if (!(OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET)) {
+				OMAP_HSMMC_WRITE(host->base, HCTL,
+					OMAP_HSMMC_READ(host->base, HCTL)
+					& SDVSCLR);
+				OMAP_HSMMC_WRITE(host->base, HCTL,
+					OMAP_HSMMC_READ(host->base, HCTL)
+					| SDVS30);
+				OMAP_HSMMC_WRITE(host->base, HCTL,
+					OMAP_HSMMC_READ(host->base, HCTL)
+					| SDBP);
+			}
+
+			clk_disable(host->fclk);
+			clk_disable(host->iclk);
+			clk_disable(host->dbclk);
+		}
+
+	}
+	return ret;
+}
+
+/* Routine to resume the MMC device */
+static int omap_mmc_resume(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct mmc_omap_host *host = platform_get_drvdata(pdev);
+
+	if (host && !host->suspended)
+		return 0;
+
+	if (host) {
+
+		ret = clk_enable(host->fclk);
+		if (ret)
+			goto clk_en_err;
+
+		ret = clk_enable(host->iclk);
+		if (ret) {
+			clk_disable(host->fclk);
+			clk_put(host->fclk);
+			goto clk_en_err;
+		}
+
+		if (clk_enable(host->dbclk) != 0)
+			dev_dbg(mmc_dev(host->mmc),
+					"Enabling debounce clk failed\n");
+
+		if (host->pdata->resume) {
+			ret = host->pdata->resume(&pdev->dev, host->slot_id);
+			if (ret)
+				dev_dbg(mmc_dev(host->mmc),
+					"Unmask interrupt failed\n");
+		}
+
+		/* Notify the core to resume the host */
+		ret = mmc_resume_host(host->mmc);
+		if (ret == 0)
+			host->suspended = 0;
+	}
+
+	return ret;
+
+clk_en_err:
+	dev_dbg(mmc_dev(host->mmc),
+		"Failed to enable MMC clocks during resume\n");
+	return ret;
+}
+
+#else
+#define omap_mmc_suspend	NULL
+#define omap_mmc_resume		NULL
+#endif
+
+static struct platform_driver omap_mmc_driver = {
+	.probe		= omap_mmc_probe,
+	.remove		= omap_mmc_remove,
+	.suspend	= omap_mmc_suspend,
+	.resume		= omap_mmc_resume,
+	.driver		= {
+		.name = DRIVER_NAME,
+		.owner = THIS_MODULE,
+	},
+};
+
+static int __init omap_mmc_init(void)
+{
+	/* Register the MMC driver */
+	return platform_driver_register(&omap_mmc_driver);
+}
+
+static void __exit omap_mmc_cleanup(void)
+{
+	/* Unregister MMC driver */
+	platform_driver_unregister(&omap_mmc_driver);
+}
+
+module_init(omap_mmc_init);
+module_exit(omap_mmc_cleanup);
+
+MODULE_DESCRIPTION("OMAP High Speed Multimedia Card driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_AUTHOR("Texas Instruments Inc");
diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c
index 3c5483b75da4..9702ad3774cf 100644
--- a/drivers/mmc/host/pxamci.c
+++ b/drivers/mmc/host/pxamci.c
@@ -180,7 +180,15 @@ static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data)
 	else
 		DALGN &= ~(1 << host->dma);
 	DDADR(host->dma) = host->sg_dma;
-	DCSR(host->dma) = DCSR_RUN;
+
+	/*
+	 * workaround for erratum #91:
+	 * only start DMA now if we are doing a read,
+	 * otherwise we wait until CMD/RESP has finished
+	 * before starting DMA.
+	 */
+	if (!cpu_is_pxa27x() || data->flags & MMC_DATA_READ)
+		DCSR(host->dma) = DCSR_RUN;
 }
 
 static void pxamci_start_cmd(struct pxamci_host *host, struct mmc_command *cmd, unsigned int cmdat)
@@ -251,23 +259,28 @@ static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat)
 	if (stat & STAT_TIME_OUT_RESPONSE) {
 		cmd->error = -ETIMEDOUT;
 	} else if (stat & STAT_RES_CRC_ERR && cmd->flags & MMC_RSP_CRC) {
-#ifdef CONFIG_PXA27x
 		/*
 		 * workaround for erratum #42:
 		 * Intel PXA27x Family Processor Specification Update Rev 001
 		 * A bogus CRC error can appear if the msb of a 136 bit
 		 * response is a one.
 		 */
-		if (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000) {
+		if (cpu_is_pxa27x() &&
+		    (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000))
 			pr_debug("ignoring CRC from command %d - *risky*\n", cmd->opcode);
-		} else
-#endif
-		cmd->error = -EILSEQ;
+		else
+			cmd->error = -EILSEQ;
 	}
 
 	pxamci_disable_irq(host, END_CMD_RES);
 	if (host->data && !cmd->error) {
 		pxamci_enable_irq(host, DATA_TRAN_DONE);
+		/*
+		 * workaround for erratum #91, if doing write
+		 * enable DMA late
+		 */
+		if (cpu_is_pxa27x() && host->data->flags & MMC_DATA_WRITE)
+			DCSR(host->dma) = DCSR_RUN;
 	} else {
 		pxamci_finish_request(host, host->mrq);
 	}
diff --git a/drivers/mmc/host/ricoh_mmc.c b/drivers/mmc/host/ricoh_mmc.c
index be9e7b32b34e..f62790513322 100644
--- a/drivers/mmc/host/ricoh_mmc.c
+++ b/drivers/mmc/host/ricoh_mmc.c
@@ -196,7 +196,7 @@ static void __devexit ricoh_mmc_remove(struct pci_dev *pdev)
 	pci_set_drvdata(pdev, NULL);
 }
 
-static int ricoh_mmc_suspend(struct pci_dev *pdev, pm_message_t state)
+static int ricoh_mmc_suspend_late(struct pci_dev *pdev, pm_message_t state)
 {
 	struct pci_dev *fw_dev = NULL;
 
@@ -210,7 +210,7 @@ static int ricoh_mmc_suspend(struct pci_dev *pdev, pm_message_t state)
 	return 0;
 }
 
-static int ricoh_mmc_resume(struct pci_dev *pdev)
+static int ricoh_mmc_resume_early(struct pci_dev *pdev)
 {
 	struct pci_dev *fw_dev = NULL;
 
@@ -229,8 +229,8 @@ static struct pci_driver ricoh_mmc_driver = {
 	.id_table =	pci_ids,
 	.probe = 	ricoh_mmc_probe,
 	.remove =	__devexit_p(ricoh_mmc_remove),
-	.suspend =	ricoh_mmc_suspend,
-	.resume =	ricoh_mmc_resume,
+	.suspend_late =	ricoh_mmc_suspend_late,
+	.resume_early =	ricoh_mmc_resume_early,
 };
 
 /*****************************************************************************\
diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c
index fcc98a4cce3c..35a98eec7414 100644
--- a/drivers/mmc/host/s3cmci.c
+++ b/drivers/mmc/host/s3cmci.c
@@ -20,7 +20,7 @@
 #include <linux/irq.h>
 #include <linux/io.h>
 
-#include <asm/dma.h>
+#include <mach/dma.h>
 
 #include <mach/regs-sdi.h>
 #include <mach/regs-gpio.h>