summaryrefslogtreecommitdiffstats
path: root/drivers/mtd
diff options
context:
space:
mode:
authorXiaolei Li <xiaolei.li@mediatek.com>2019-05-07 12:25:39 +0200
committerMiquel Raynal <miquel.raynal@bootlin.com>2019-06-27 20:05:24 +0200
commit42d13a09efa4f0ea33231f3b145356ee487987b3 (patch)
tree09ff1733029904e56066d37950c0f3e00b810f6b /drivers/mtd
parentmtd: rawnand: mtk: Correct low level time calculation of r/w cycle (diff)
downloadlinux-42d13a09efa4f0ea33231f3b145356ee487987b3.tar.xz
linux-42d13a09efa4f0ea33231f3b145356ee487987b3.zip
mtd: rawnand: mtk: Improve data sampling timing for read cycle
Currently, we expand RE# low level time by choosing the max value between RE# pulse width and RE# access time, and sample data at the rising edge of RE#. Then, if RE# access time is bigger than RE# pulse width, the real read cycle time may be more than NAND SPEC required. This makes read performance be worse than that expected. This patch improves data sampling timing by calculating RE# low level time according to RE# pulse width. If RE# access time is bigger than RE# pulse width, then delay sampling data timing. The result of contrast test base on MT2712 evaluat board is as follow. nand: Micron MT29F16G08ADBCAH4 nand: 2048 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 NFI 2x clock rate: 124800000 HZ. Read speed without this patch: mtd_speedtest: page read speed is 14012 KiB/s mtd_speedtest: 2 page read speed is 14860 KiB/s Read speed with this patch: mtd_speedtest: page read speed is 18724 KiB/s mtd_speedtest: 2 page read speed is 18713 KiB/s Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Diffstat (limited to 'drivers/mtd')
-rw-r--r--drivers/mtd/nand/raw/mtk_nand.c46
1 files changed, 36 insertions, 10 deletions
diff --git a/drivers/mtd/nand/raw/mtk_nand.c b/drivers/mtd/nand/raw/mtk_nand.c
index 23fe19397315..03aff7e9bea5 100644
--- a/drivers/mtd/nand/raw/mtk_nand.c
+++ b/drivers/mtd/nand/raw/mtk_nand.c
@@ -79,6 +79,10 @@
#define NFI_FDMM(x) (0xA4 + (x) * sizeof(u32) * 2)
#define NFI_FDM_MAX_SIZE (8)
#define NFI_FDM_MIN_SIZE (1)
+#define NFI_DEBUG_CON1 (0x220)
+#define STROBE_MASK GENMASK(4, 3)
+#define STROBE_SHIFT (3)
+#define MAX_STROBE_DLY (3)
#define NFI_MASTER_STA (0x224)
#define MASTER_STA_MASK (0x0FFF)
#define NFI_EMPTY_THRESH (0x23C)
@@ -501,7 +505,7 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
struct mtk_nfc *nfc = nand_get_controller_data(chip);
const struct nand_sdr_timings *timings;
u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
- u32 thold;
+ u32 temp, tsel = 0;
timings = nand_get_sdr_timings(conf);
if (IS_ERR(timings))
@@ -538,30 +542,52 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
twh &= 0xf;
/* Calculate real WE#/RE# hold time in nanosecond */
- thold = (twh + 1) * 1000000 / rate;
+ temp = (twh + 1) * 1000000 / rate;
/* nanosecond to picosecond */
- thold *= 1000;
+ temp *= 1000;
/*
* WE# low level time should be expaned to meet WE# pulse time
* and WE# cycle time at the same time.
*/
- if (thold < timings->tWC_min)
- twst = timings->tWC_min - thold;
+ if (temp < timings->tWC_min)
+ twst = timings->tWC_min - temp;
twst = max(timings->tWP_min, twst) / 1000;
twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
twst &= 0xf;
/*
- * RE# low level time should be expaned to meet RE# pulse time,
- * RE# access time and RE# cycle time at the same time.
+ * RE# low level time should be expaned to meet RE# pulse time
+ * and RE# cycle time at the same time.
*/
- if (thold < timings->tRC_min)
- trlt = timings->tRC_min - thold;
- trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
+ if (temp < timings->tRC_min)
+ trlt = timings->tRC_min - temp;
+ trlt = max(trlt, timings->tRP_min) / 1000;
trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
trlt &= 0xf;
+ /* Calculate RE# pulse time in nanosecond. */
+ temp = (trlt + 1) * 1000000 / rate;
+ /* nanosecond to picosecond */
+ temp *= 1000;
+ /*
+ * If RE# access time is bigger than RE# pulse time,
+ * delay sampling data timing.
+ */
+ if (temp < timings->tREA_max) {
+ tsel = timings->tREA_max / 1000;
+ tsel = DIV_ROUND_UP(tsel * rate, 1000000);
+ tsel -= (trlt + 1);
+ if (tsel > MAX_STROBE_DLY) {
+ trlt += tsel - MAX_STROBE_DLY;
+ tsel = MAX_STROBE_DLY;
+ }
+ }
+ temp = nfi_readl(nfc, NFI_DEBUG_CON1);
+ temp &= ~STROBE_MASK;
+ temp |= tsel << STROBE_SHIFT;
+ nfi_writel(nfc, temp, NFI_DEBUG_CON1);
+
/*
* ACCON: access timing control register
* -------------------------------------