mtd: spi-nor: spansion: Rework cypress_nor_quad_enable_volatile() for multi-chip device support

Rework quad method for multi-chip devices by updating CFR1V in all
dice in the device.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/1b5606dbcc11b3432c306a75880f05c68e927fb9.1680849425.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

1 files changed, 39 insertions, 21 deletions

diff --git a/drivers/mtd/spi-nor/spansion.c b/drivers/mtd/spi-nor/spansion.c
index 5e021e20497b..91bc0aace516 100644
--- a/drivers/mtd/spi-nor/spansion.c
+++ b/drivers/mtd/spi-nor/spansion.c
@@ -139,21 +139,7 @@ static int cypress_nor_octal_dtr_dis(struct spi_nor *nor)
 	return 0;
 }
 
-/**
- * cypress_nor_quad_enable_volatile() - enable Quad I/O mode in volatile
- *                                      register.
- * @nor:	pointer to a 'struct spi_nor'
- *
- * It is recommended to update volatile registers in the field application due
- * to a risk of the non-volatile registers corruption by power interrupt. This
- * function sets Quad Enable bit in CFR1 volatile. If users set the Quad Enable
- * bit in the CFR1 non-volatile in advance (typically by a Flash programmer
- * before mounting Flash on PCB), the Quad Enable bit in the CFR1 volatile is
- * also set during Flash power-up.
- *
- * Return: 0 on success, -errno otherwise.
- */
-static int cypress_nor_quad_enable_volatile(struct spi_nor *nor)
+static int cypress_nor_quad_enable_volatile_reg(struct spi_nor *nor, u64 addr)
 {
 	struct spi_mem_op op;
 	u8 addr_mode_nbytes = nor->params->addr_mode_nbytes;
@@ -161,8 +147,7 @@ static int cypress_nor_quad_enable_volatile(struct spi_nor *nor)
 	int ret;
 
 	op = (struct spi_mem_op)
-		CYPRESS_NOR_RD_ANY_REG_OP(addr_mode_nbytes,
-					  SPINOR_REG_CYPRESS_CFR1V, 0,
+		CYPRESS_NOR_RD_ANY_REG_OP(addr_mode_nbytes, addr, 0,
 					  nor->bouncebuf);
 
 	ret = spi_nor_read_any_reg(nor, &op, nor->reg_proto);
@@ -175,8 +160,7 @@ static int cypress_nor_quad_enable_volatile(struct spi_nor *nor)
 	/* Update the Quad Enable bit. */
 	nor->bouncebuf[0] |= SPINOR_REG_CYPRESS_CFR1_QUAD_EN;
 	op = (struct spi_mem_op)
-		CYPRESS_NOR_WR_ANY_REG_OP(addr_mode_nbytes,
-					  SPINOR_REG_CYPRESS_CFR1V, 1,
+		CYPRESS_NOR_WR_ANY_REG_OP(addr_mode_nbytes, addr, 1,
 					  nor->bouncebuf);
 	ret = spi_nor_write_any_volatile_reg(nor, &op, nor->reg_proto);
 	if (ret)
@@ -186,8 +170,7 @@ static int cypress_nor_quad_enable_volatile(struct spi_nor *nor)
 
 	/* Read back and check it. */
 	op = (struct spi_mem_op)
-		CYPRESS_NOR_RD_ANY_REG_OP(addr_mode_nbytes,
-					  SPINOR_REG_CYPRESS_CFR1V, 0,
+		CYPRESS_NOR_RD_ANY_REG_OP(addr_mode_nbytes, addr, 0,
 					  nor->bouncebuf);
 	ret = spi_nor_read_any_reg(nor, &op, nor->reg_proto);
 	if (ret)
@@ -202,6 +185,41 @@ static int cypress_nor_quad_enable_volatile(struct spi_nor *nor)
 }
 
 /**
+ * cypress_nor_quad_enable_volatile() - enable Quad I/O mode in volatile
+ *                                      register.
+ * @nor:	pointer to a 'struct spi_nor'
+ *
+ * It is recommended to update volatile registers in the field application due
+ * to a risk of the non-volatile registers corruption by power interrupt. This
+ * function sets Quad Enable bit in CFR1 volatile. If users set the Quad Enable
+ * bit in the CFR1 non-volatile in advance (typically by a Flash programmer
+ * before mounting Flash on PCB), the Quad Enable bit in the CFR1 volatile is
+ * also set during Flash power-up.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int cypress_nor_quad_enable_volatile(struct spi_nor *nor)
+{
+	struct spi_nor_flash_parameter *params = nor->params;
+	u64 addr;
+	u8 i;
+	int ret;
+
+	if (!params->n_dice)
+		return cypress_nor_quad_enable_volatile_reg(nor,
+						SPINOR_REG_CYPRESS_CFR1V);
+
+	for (i = 0; i < params->n_dice; i++) {
+		addr = params->vreg_offset[i] + SPINOR_REG_CYPRESS_CFR1;
+		ret = cypress_nor_quad_enable_volatile_reg(nor, addr);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+/**
  * cypress_nor_determine_addr_mode_by_sr1() - Determine current address mode
  *                                            (3 or 4-byte) by querying status
  *                                            register 1 (SR1).