Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c

1 files changed, 18 insertions, 28 deletions

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 7b832c727f87..2decc597bda7 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -483,7 +483,7 @@ config XTENSA_XT2000_SONIC
 	  This is the driver for the onboard card of the Xtensa XT2000 board.
 
 config MIPS_AU1X00_ENET
-	bool "MIPS AU1000 Ethernet support"
+	tristate "MIPS AU1000 Ethernet support"
 	depends on SOC_AU1X00
 	select PHYLIB
 	select CRC32
@@ -887,6 +887,13 @@ config BFIN_MAC_RMII
 	help
 	  Use Reduced PHY MII Interface
 
+config BFIN_MAC_USE_HWSTAMP
+	bool "Use IEEE 1588 hwstamp"
+	depends on BFIN_MAC && BF518
+	default y
+	help
+	  To support the IEEE 1588 Precision Time Protocol (PTP), select y here
+
 config SMC9194
 	tristate "SMC 9194 support"
 	depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
@@ -1453,20 +1460,6 @@ config FORCEDETH
 	  To compile this driver as a module, choose M here. The module
 	  will be called forcedeth.
 
-config FORCEDETH_NAPI
-	bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
-	depends on FORCEDETH && EXPERIMENTAL
-	help
-	  NAPI is a new driver API designed to reduce CPU and interrupt load
-	  when the driver is receiving lots of packets from the card. It is
-	  still somewhat experimental and thus not yet enabled by default.
-
-	  If your estimated Rx load is 10kpps or more, or if the card will be
-	  deployed on potentially unfriendly networks (e.g. in a firewall),
-	  then say Y here.
-
-	  If in doubt, say N.
-
 config CS89x0
 	tristate "CS89x0 support"
 	depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
@@ -1916,6 +1909,7 @@ config FEC
 	bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
 	depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
 		MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5
+	select PHYLIB
 	help
 	  Say Y here if you want to use the built-in 10/100 Fast ethernet
 	  controller on some Motorola ColdFire and Freescale i.MX processors.
@@ -2434,8 +2428,8 @@ config MV643XX_ETH
 
 config XILINX_LL_TEMAC
 	tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
+	depends on PPC || MICROBLAZE
 	select PHYLIB
-	depends on PPC_DCR_NATIVE
 	help
 	  This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
 	  core used in Xilinx Spartan and Virtex FPGAs
@@ -2618,11 +2612,11 @@ config EHEA
 	  will be called ehea.
 
 config ENIC
-	tristate "Cisco 10G Ethernet NIC support"
+	tristate "Cisco VIC Ethernet NIC Support"
 	depends on PCI && INET
 	select INET_LRO
 	help
-	  This enables the support for the Cisco 10G Ethernet card.
+	  This enables the support for the Cisco VIC Ethernet card.
 
 config IXGBE
 	tristate "Intel(R) 10GbE PCI Express adapters support"
@@ -2862,6 +2856,8 @@ source "drivers/ieee802154/Kconfig"
 
 source "drivers/s390/net/Kconfig"
 
+source "drivers/net/caif/Kconfig"
+
 config XEN_NETDEV_FRONTEND
 	tristate "Xen network device frontend driver"
 	depends on XEN
@@ -3180,17 +3176,12 @@ config PPPOATM
 
 config PPPOL2TP
 	tristate "PPP over L2TP (EXPERIMENTAL)"
-	depends on EXPERIMENTAL && PPP && INET
+	depends on EXPERIMENTAL && L2TP && PPP
 	help
 	  Support for PPP-over-L2TP socket family. L2TP is a protocol
 	  used by ISPs and enterprises to tunnel PPP traffic over UDP
 	  tunnels. L2TP is replacing PPTP for VPN uses.
 
-	  This kernel component handles only L2TP data packets: a
-	  userland daemon handles L2TP the control protocol (tunnel
-	  and session setup). One such daemon is OpenL2TP
-	  (http://openl2tp.sourceforge.net/).
-
 config SLIP
 	tristate "SLIP (serial line) support"
 	---help---
@@ -3277,15 +3268,14 @@ config NET_FC
 	  "SCSI generic support".
 
 config NETCONSOLE
-	tristate "Network console logging support (EXPERIMENTAL)"
-	depends on EXPERIMENTAL
+	tristate "Network console logging support"
 	---help---
 	If you want to log kernel messages over the network, enable this.
 	See <file:Documentation/networking/netconsole.txt> for details.
 
 config NETCONSOLE_DYNAMIC
-	bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
-	depends on NETCONSOLE && SYSFS && EXPERIMENTAL
+	bool "Dynamic reconfiguration of logging targets"
+	depends on NETCONSOLE && SYSFS
 	select CONFIGFS_FS
 	help
 	  This option enables the ability to dynamically reconfigure target