Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 169 insertions, 0 deletions

diff --git a/drivers/net/de600.h b/drivers/net/de600.h
new file mode 100644
index 000000000000..e4073015dcd8
--- /dev/null
+++ b/drivers/net/de600.h
@@ -0,0 +1,169 @@
+/**************************************************
+ *                                                *
+ * Definition of D-Link Ethernet Pocket adapter   *
+ *                                                *
+ **************************************************/
+/*
+ * D-Link Ethernet pocket adapter ports
+ */
+/*
+ * OK, so I'm cheating, but there are an awful lot of
+ * reads and writes in order to get anything in and out
+ * of the DE-600 with 4 bits at a time in the parallel port,
+ * so every saved instruction really helps :-)
+ */
+
+#ifndef DE600_IO
+#define DE600_IO	0x378
+#endif
+
+#define DATA_PORT	(DE600_IO)
+#define STATUS_PORT	(DE600_IO + 1)
+#define COMMAND_PORT	(DE600_IO + 2)
+
+#ifndef DE600_IRQ
+#define DE600_IRQ	7
+#endif
+/*
+ * It really should look like this, and autoprobing as well...
+ *
+#define DATA_PORT	(dev->base_addr + 0)
+#define STATUS_PORT	(dev->base_addr + 1)
+#define COMMAND_PORT	(dev->base_addr + 2)
+#define DE600_IRQ	dev->irq
+ */
+
+/*
+ * D-Link COMMAND_PORT commands
+ */
+#define SELECT_NIC	0x04 /* select Network Interface Card */
+#define SELECT_PRN	0x1c /* select Printer */
+#define NML_PRN		0xec /* normal Printer situation */
+#define IRQEN		0x10 /* enable IRQ line */
+
+/*
+ * D-Link STATUS_PORT
+ */
+#define RX_BUSY		0x80
+#define RX_GOOD		0x40
+#define TX_FAILED16	0x10
+#define TX_BUSY		0x08
+
+/*
+ * D-Link DATA_PORT commands
+ * command in low 4 bits
+ * data in high 4 bits
+ * select current data nibble with HI_NIBBLE bit
+ */
+#define WRITE_DATA	0x00 /* write memory */
+#define READ_DATA	0x01 /* read memory */
+#define STATUS		0x02 /* read  status register */
+#define COMMAND		0x03 /* write command register (see COMMAND below) */
+#define NULL_COMMAND	0x04 /* null command */
+#define RX_LEN		0x05 /* read  received packet length */
+#define TX_ADDR		0x06 /* set adapter transmit memory address */
+#define RW_ADDR		0x07 /* set adapter read/write memory address */
+#define HI_NIBBLE	0x08 /* read/write the high nibble of data,
+				or-ed with rest of command */
+
+/*
+ * command register, accessed through DATA_PORT with low bits = COMMAND
+ */
+#define RX_ALL		0x01 /* PROMISCUOUS */
+#define RX_BP		0x02 /* default: BROADCAST & PHYSICAL ADDRESS */
+#define RX_MBP		0x03 /* MULTICAST, BROADCAST & PHYSICAL ADDRESS */
+
+#define TX_ENABLE	0x04 /* bit 2 */
+#define RX_ENABLE	0x08 /* bit 3 */
+
+#define RESET		0x80 /* set bit 7 high */
+#define STOP_RESET	0x00 /* set bit 7 low */
+
+/*
+ * data to command register
+ * (high 4 bits in write to DATA_PORT)
+ */
+#define RX_PAGE2_SELECT	0x10 /* bit 4, only 2 pages to select */
+#define RX_BASE_PAGE	0x20 /* bit 5, always set when specifying RX_ADDR */
+#define FLIP_IRQ	0x40 /* bit 6 */
+
+/*
+ * D-Link adapter internal memory:
+ *
+ * 0-2K 1:st transmit page (send from pointer up to 2K)
+ * 2-4K	2:nd transmit page (send from pointer up to 4K)
+ *
+ * 4-6K 1:st receive page (data from 4K upwards)
+ * 6-8K 2:nd receive page (data from 6K upwards)
+ *
+ * 8K+	Adapter ROM (contains magic code and last 3 bytes of Ethernet address)
+ */
+#define MEM_2K		0x0800 /* 2048 */
+#define MEM_4K		0x1000 /* 4096 */
+#define MEM_6K		0x1800 /* 6144 */
+#define NODE_ADDRESS	0x2000 /* 8192 */
+
+#define RUNT 60		/* Too small Ethernet packet */
+
+/**************************************************
+ *                                                *
+ *             End of definition                  *
+ *                                                *
+ **************************************************/
+
+/*
+ * Index to functions, as function prototypes.
+ */
+/* Routines used internally. (See "convenience macros") */
+static u8	de600_read_status(struct net_device *dev);
+static u8	de600_read_byte(unsigned char type, struct net_device *dev);
+
+/* Put in the device structure. */
+static int	de600_open(struct net_device *dev);
+static int	de600_close(struct net_device *dev);
+static struct net_device_stats *get_stats(struct net_device *dev);
+static int	de600_start_xmit(struct sk_buff *skb, struct net_device *dev);
+
+/* Dispatch from interrupts. */
+static irqreturn_t de600_interrupt(int irq, void *dev_id, struct pt_regs *regs);
+static int	de600_tx_intr(struct net_device *dev, int irq_status);
+static void	de600_rx_intr(struct net_device *dev);
+
+/* Initialization */
+static void	trigger_interrupt(struct net_device *dev);
+static int	adapter_init(struct net_device *dev);
+
+/*
+ * Convenience macros/functions for D-Link adapter
+ */
+
+#define select_prn() outb_p(SELECT_PRN, COMMAND_PORT); DE600_SLOW_DOWN
+#define select_nic() outb_p(SELECT_NIC, COMMAND_PORT); DE600_SLOW_DOWN
+
+/* Thanks for hints from Mark Burton <markb@ordern.demon.co.uk> */
+#define de600_put_byte(data) ( \
+	outb_p(((data) << 4)   | WRITE_DATA            , DATA_PORT), \
+	outb_p(((data) & 0xf0) | WRITE_DATA | HI_NIBBLE, DATA_PORT))
+
+/*
+ * The first two outb_p()'s below could perhaps be deleted if there
+ * would be more delay in the last two. Not certain about it yet...
+ */
+#define de600_put_command(cmd) ( \
+	outb_p(( rx_page        << 4)   | COMMAND            , DATA_PORT), \
+	outb_p(( rx_page        & 0xf0) | COMMAND | HI_NIBBLE, DATA_PORT), \
+	outb_p(((rx_page | cmd) << 4)   | COMMAND            , DATA_PORT), \
+	outb_p(((rx_page | cmd) & 0xf0) | COMMAND | HI_NIBBLE, DATA_PORT))
+
+#define de600_setup_address(addr,type) ( \
+	outb_p((((addr) << 4) & 0xf0) | type            , DATA_PORT), \
+	outb_p(( (addr)       & 0xf0) | type | HI_NIBBLE, DATA_PORT), \
+	outb_p((((addr) >> 4) & 0xf0) | type            , DATA_PORT), \
+	outb_p((((addr) >> 8) & 0xf0) | type | HI_NIBBLE, DATA_PORT))
+
+#define rx_page_adr() ((rx_page & RX_PAGE2_SELECT)?(MEM_6K):(MEM_4K))
+
+/* Flip bit, only 2 pages */
+#define next_rx_page() (rx_page ^= RX_PAGE2_SELECT)
+
+#define tx_page_adr(a) (((a) + 1) * MEM_2K)