dgrs: remove from build, config, and maintainer list

Stop building and configuring driver for Digi RightSwitch, which was
never actually sold to anyone, and remove it from MAINTAINERS.

In response to an investigation into the firmware of the "Digi Rightswitch"
driver, Andres Salomon discovered:
>
> Dear Andres:
>
> After further research, we found that this product was killed in place
> and never reached the market.  We would like to request that this not be
> included.

Since the product never reached market, clearly nobody is using this orphaned
driver.

Signed-off-by: Nathanael Nerode <neroden@gcc.gnu.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 0 insertions, 183 deletions

diff --git a/drivers/net/dgrs_es4h.h b/drivers/net/dgrs_es4h.h
deleted file mode 100644
index 5518fba46b2c..000000000000
--- a/drivers/net/dgrs_es4h.h
+++ /dev/null
@@ -1,183 +0,0 @@
-/************************************************************************/
-/*									*/
-/*	es4h.h:	Hardware definition of the ES/4h Ethernet Switch, from	*/
-/*		both the host and the 3051's point of view.		*/
-/*		NOTE: this name is a misnomer now that there is a PCI	*/
-/*		board.  Everything that says "es4h" should really be	*/
-/*		"se4".  But we'll keep the old name for now.		*/
-/*									*/
-/*	$Id: es4h.h,v 1.10 1996/08/22 17:16:53 rick Exp $		*/
-/*									*/
-/************************************************************************/
-
-/************************************************************************/
-/*									*/
-/*	EISA I/O Registers.  These are located at 0x1000 * slot-number	*/
-/*	plus the indicated address.  I.E. 0x4000-0x4009 for slot 4.	*/
-/*									*/
-/************************************************************************/
-
-#define	ES4H_MANUFmsb	0x00		/* Read-only */
-#define	ES4H_MANUFlsb	0x01		/* Read-only */
-#	define ES4H_MANUF_CODE		0x1049	/* = "DBI" */
-
-#define	ES4H_PRODUCT	0x02		/* Read-only */
-#	define ES4H_PRODUCT_CODE	0x0A
-#	define EPC_PRODUCT_CODE		0x03
-
-#define	ES4H_REVISION	0x03		/* Read-only */
-#	define ES4H_REVISION_CODE	0x01
-
-#define	ES4H_EC		0x04		/* EISA Control */
-#	define ES4H_EC_RESET		0x04	/* WO, EISA reset */
-#	define ES4H_EC_ENABLE		0x01	/* RW, EISA enable - set to */
-						/* 1 before memory enable */
-#define	ES4H_PC		0x05		/* Processor Control */
-#	define ES4H_PC_RESET		0x04	/* RW, 3051 reset */
-#	define ES4H_PC_INT		0x08	/* WO, assert 3051 intr. 3 */
-
-#define	ES4H_MW		0x06		/* Memory Window select and enable */
-#	define ES4H_MW_ENABLE		0x80	/* WO, enable memory */
-#	define ES4H_MW_SELECT_MASK	0x1f	/* WO, 32k window selected */
-
-#define	ES4H_IS		0x07		/* Interrupt, addr select */
-#	define ES4H_IS_INTMASK		0x07	/* WO, interrupt select */
-#	define ES4H_IS_INTOFF		0x00		/* No IRQ */
-#	define ES4H_IS_INT3		0x03		/* IRQ 3 */
-#	define ES4H_IS_INT5		0x02		/* IRQ 5 */
-#	define ES4H_IS_INT7		0x01		/* IRQ 7 */
-#	define ES4H_IS_INT10		0x04		/* IRQ 10 */
-#	define ES4H_IS_INT11		0x05		/* IRQ 11 */
-#	define ES4H_IS_INT12		0x06		/* IRQ 12 */
-#	define ES4H_IS_INT15		0x07		/* IRQ 15 */
-#	define ES4H_IS_INTACK		0x10	/* WO, interrupt ack */
-#	define ES4H_IS_INTPEND		0x10	/* RO, interrupt pending */
-#	define ES4H_IS_LINEAR		0x40	/* WO, no memory windowing */
-#	define ES4H_IS_AS15		0x80	/* RW, address select bit 15 */
-
-#define	ES4H_AS_23_16	0x08		/* Address select bits 23-16 */
-#define	ES4H_AS_31_24	0x09		/* Address select bits 31-24 */
-
-#define ES4H_IO_MAX		0x09		/* Size of I/O space */
-
-/*
- * PCI
- */
-#define SE6_RESET		PLX_USEROUT
-
-/************************************************************************/
-/*									*/
-/*	3051 Memory Map							*/
-/*									*/
-/*	Note: 3051 has 4K I-cache, 2K D-cache.  1 cycle is 50 nsec.	*/
-/*									*/
-/************************************************************************/
-#define	SE4_NPORTS		4		/* # of ethernet ports */
-#define	SE6_NPORTS		6		/* # of ethernet ports */
-#define	SE_NPORTS		6		/* Max # of ethernet ports */
-
-#define	ES4H_RAM_BASE		0x83000000	/* Base address of RAM */
-#define	ES4H_RAM_SIZE		0x00200000	/* Size of RAM (2MB) */
-#define	ES4H_RAM_INTBASE	0x83800000	/* Base of int-on-write RAM */
-						/* a.k.a. PKT RAM */
-
-						/* Ethernet controllers */
-						/* See: i82596.h */
-#define	ES4H_ETHER0_PORT	0xA2000000
-#define	ES4H_ETHER0_CMD		0xA2000100
-#define	ES4H_ETHER1_PORT	0xA2000200
-#define	ES4H_ETHER1_CMD		0xA2000300
-#define	ES4H_ETHER2_PORT	0xA2000400
-#define	ES4H_ETHER2_CMD		0xA2000500
-#define	ES4H_ETHER3_PORT	0xA2000600
-#define	ES4H_ETHER3_CMD		0xA2000700
-#define	ES4H_ETHER4_PORT	0xA2000800	/* RS SE-6 only */
-#define	ES4H_ETHER4_CMD		0xA2000900	/* RS SE-6 only */
-#define	ES4H_ETHER5_PORT	0xA2000A00	/* RS SE-6 only */
-#define	ES4H_ETHER5_CMD		0xA2000B00	/* RS SE-6 only */
-
-#define	ES4H_I8254		0xA2040000	/* 82C54 timers */
-						/* See: i8254.h */
-
-#define	SE4_I8254_HZ		(23000000/4)	/* EISA clock input freq. */
-#define	SE4_IDT_HZ		(46000000)	/* EISA CPU freq. */
-#define	SE6_I8254_HZ		(20000000/4)	/* PCI clock input freq. */
-#define	SE6_IDT_HZ		(50000000)	/* PCI CPU freq. */
-#define	ES4H_I8254_HZ		(23000000/4)	/* EISA clock input freq. */
-
-#define	ES4H_GPP		0xA2050000	/* General purpose port */
-	/*
-	 * SE-4 (EISA) GPP bits
-	 */
-#	define ES4H_GPP_C0_100		0x0001	/* WO, Chan 0: 100 ohm TP */
-#	define ES4H_GPP_C0_SQE		0x0002	/* WO, Chan 0: normal squelch */
-#	define ES4H_GPP_C1_100		0x0004	/* WO, Chan 1: 100 ohm TP */
-#	define ES4H_GPP_C1_SQE		0x0008	/* WO, Chan 1: normal squelch */
-#	define ES4H_GPP_C2_100		0x0010	/* WO, Chan 2: 100 ohm TP */
-#	define ES4H_GPP_C2_SQE		0x0020	/* WO, Chan 2: normal squelch */
-#	define ES4H_GPP_C3_100		0x0040	/* WO, Chan 3: 100 ohm TP */
-#	define ES4H_GPP_C3_SQE		0x0080	/* WO, Chan 3: normal squelch */
-#	define ES4H_GPP_SQE		0x00AA	/* WO, All: normal squelch */
-#	define ES4H_GPP_100		0x0055	/* WO, All: 100 ohm TP */
-#	define ES4H_GPP_HOSTINT		0x0100	/* RO, cause intr. to host */
-						/* Hold high > 250 nsec */
-#	define SE4_GPP_EED		0x0200	/* RW, EEPROM data bit */
-#	define SE4_GPP_EECS		0x0400	/* RW, EEPROM chip select */
-#	define SE4_GPP_EECK		0x0800	/* RW, EEPROM clock */
-
-	/*
-	 * SE-6 (PCI) GPP bits
-	 */
-#	define SE6_GPP_EED		0x0001	/* RW, EEPROM data bit */
-#	define SE6_GPP_EECS		0x0002	/* RW, EEPROM chip select */
-#	define SE6_GPP_EECK		0x0004	/* RW, EEPROM clock */
-#	define SE6_GPP_LINK		0x00fc	/* R, Link status LEDs */
-
-#define	ES4H_INTVEC		0xA2060000	/* RO: Interrupt Vector */
-#	define ES4H_IV_DMA0		0x01	/* Chan 0 DMA interrupt */
-#	define ES4H_IV_PKT0		0x02	/* Chan 0 PKT interrupt */
-#	define ES4H_IV_DMA1		0x04	/* Chan 1 DMA interrupt */
-#	define ES4H_IV_PKT1		0x08	/* Chan 1 PKT interrupt */
-#	define ES4H_IV_DMA2		0x10	/* Chan 2 DMA interrupt */
-#	define ES4H_IV_PKT2		0x20	/* Chan 2 PKT interrupt */
-#	define ES4H_IV_DMA3		0x40	/* Chan 3 DMA interrupt */
-#	define ES4H_IV_PKT3		0x80	/* Chan 3 PKT interrupt */
-
-#define	ES4H_INTACK		0xA2060000	/* WO: Interrupt Ack */
-#	define ES4H_INTACK_8254		0x01	/* Real Time Clock (int 0) */
-#	define ES4H_INTACK_HOST		0x02	/* Host (int 1) */
-#	define ES4H_INTACK_PKT0		0x04	/* Chan 0 Pkt (int 2) */
-#	define ES4H_INTACK_PKT1		0x08	/* Chan 1 Pkt (int 3) */
-#	define ES4H_INTACK_PKT2		0x10	/* Chan 2 Pkt (int 4) */
-#	define ES4H_INTACK_PKT3		0x20	/* Chan 3 Pkt (int 5) */
-
-#define	SE6_PLX			0xA2070000	/* PLX 9060, SE-6 (PCI) only */
-						/* see plx9060.h */
-
-#define	SE6_PCI_VENDOR_ID	0x114F		/* Digi PCI vendor ID */
-#define	SE6_PCI_DEVICE_ID	0x0003		/* RS SE-6 device ID */
-#define	SE6_PCI_ID		((SE6_PCI_DEVICE_ID<<16) | SE6_PCI_VENDOR_ID)
-
-/*
- *	IDT Interrupts
- */
-#define	ES4H_INT_8254		IDT_INT0
-#define	ES4H_INT_HOST		IDT_INT1
-#define	ES4H_INT_ETHER0		IDT_INT2
-#define	ES4H_INT_ETHER1		IDT_INT3
-#define	ES4H_INT_ETHER2		IDT_INT4
-#define	ES4H_INT_ETHER3		IDT_INT5
-
-/*
- *	Because there are differences between the SE-4 and the SE-6,
- *	we assume that the following globals will be set up at init
- *	time in main.c to containt the appropriate constants from above
- */
-extern ushort	Gpp;		/* Softcopy of GPP register */
-extern ushort	EEck;		/* Clock bit */
-extern ushort	EEcs;		/* CS bit */
-extern ushort	EEd;		/* Data bit */
-extern ulong	I8254_Hz;	/* i8254 input frequency */
-extern ulong	IDT_Hz;		/* IDT CPU frequency */
-extern int	Nports;		/* Number of ethernet controllers */
-extern int	Nchan;		/* Nports+1 */