dgrs: remove from build, config, and maintainer list

Stop building and configuring driver for Digi RightSwitch, which was
never actually sold to anyone, and remove it from MAINTAINERS.

In response to an investigation into the firmware of the "Digi Rightswitch"
driver, Andres Salomon discovered:
>
> Dear Andres:
>
> After further research, we found that this product was killed in place
> and never reached the market.  We would like to request that this not be
> included.

Since the product never reached market, clearly nobody is using this orphaned
driver.

Signed-off-by: Nathanael Nerode <neroden@gcc.gnu.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 0 insertions, 175 deletions

diff --git a/drivers/net/dgrs_plx9060.h b/drivers/net/dgrs_plx9060.h
deleted file mode 100644
index 6888ae0d0ce0..000000000000
--- a/drivers/net/dgrs_plx9060.h
+++ /dev/null
@@ -1,175 +0,0 @@
-/*
- *	PLX 9060 PCI Interface chip
- */
-
-/*
- *	PCI configuration registers, same offset on local and PCI sides,
- *	but on PCI side, must use PCI BIOS calls to read/write.
- */
-#define	PCI_PLXREGS_BASE_ADDR	0x10
-
-#define	PCI_PLXREGS_IO_ADDR	0x14
-
-#define	PCI_SPACE0_BASE_ADDR	0x18
-
-#define	PCI_ROM_BASE_ADDR	0x30
-#	define PCI_ROM_ENABLED		0x00000001
-
-#define	PCI_INT_LINE		0x3C
-
-/*
- *	Registers accessible directly from PCI and local side.
- *	Offset is from PCI side.  Add PLX_LCL_OFFSET for local address.
- */
-#define	PLX_LCL_OFFSET	0x80	/* Offset of regs from local side */
-
-/*
- *	Local Configuration Registers
- */
-#define	PLX_SPACE0_RANGE	0x00	/* Range for PCI to Lcl Addr Space 0 */
-#define	PLX_SPACE0_BASE_ADDR	0x04	/* Lcl Base address remap */
-
-#define	PLX_ROM_RANGE		0x10	/* Range for expansion ROM (DMA) */
-#define	PLX_ROM_BASE_ADDR	0x14	/* Lcl base address remap for ROM */
-
-#define	PLX_BUS_REGION		0x18	/* Bus Region Descriptors */
-
-/*
- *	Shared Run Time Registers
- */
-#define	PLX_MBOX0		0x40
-#define	PLX_MBOX1		0x44
-#define	PLX_MBOX2		0x48
-#define	PLX_MBOX3		0x4C
-#define	PLX_MBOX4		0x50
-#define	PLX_MBOX5		0x54
-#define	PLX_MBOX6		0x58
-#define	PLX_MBOX7		0x5C
-
-#define	PLX_PCI2LCL_DOORBELL	0x60
-
-#define	PLX_LCL2PCI_DOORBELL	0x64
-
-#define	PLX_INT_CSR		0x68	/* Interrupt Control/Status */
-#	define	PLX_LSERR_ENABLE	0x00000001
-#	define	PLX_LSERR_PE		0x00000002
-#	define	PLX_SERR		0x00000004
-#	undef  PLX_UNUSED /*		0x00000008			*/
-#	undef  PLX_UNUSED /*		0x00000010			*/
-#	undef  PLX_UNUSED /*		0x00000020			*/
-#	undef  PLX_UNUSED /*		0x00000040			*/
-#	undef  PLX_UNUSED /*		0x00000080			*/
-#	define PLX_PCI_IE		0x00000100
-#	define	PLX_PCI_DOORBELL_IE	0x00000200
-#	define	PLX_PCI_ABORT_IE	0x00000400
-#	define	PLX_PCI_LOCAL_IE	0x00000800
-#	define	PLX_RETRY_ABORT_ENABLE	0x00001000
-#	define	PLX_PCI_DOORBELL_INT	0x00002000
-#	define	PLX_PCI_ABORT_INT	0x00004000
-#	define	PLX_PCI_LOCAL_INT	0x00008000
-#	define	PLX_LCL_IE		0x00010000
-#	define	PLX_LCL_DOORBELL_IE	0x00020000
-#	define	PLX_LCL_DMA0_IE		0x00040000
-#	define	PLX_LCL_DMA1_IE		0x00080000
-#	define	PLX_LCL_DOORBELL_INT	0x00100000
-#	define	PLX_LCL_DMA0_INT	0x00200000
-#	define	PLX_LCL_DMA1_INT	0x00400000
-#	define	PLX_LCL_BIST_INT	0x00800000
-#	define	PLX_BM_DIRECT_		0x01000000
-#	define	PLX_BM_DMA0_		0x02000000
-#	define	PLX_BM_DMA1_		0x04000000
-#	define	PLX_BM_ABORT_		0x08000000
-#	undef  PLX_UNUSED /*		0x10000000			*/
-#	undef  PLX_UNUSED /*		0x20000000			*/
-#	undef  PLX_UNUSED /*		0x40000000			*/
-#	undef  PLX_UNUSED /*		0x80000000			*/
-
-#define	PLX_MISC_CSR		0x6c	/* EEPROM,PCI,User,Init Control/Status*/
-#	define PLX_USEROUT		0x00010000
-#	define PLX_USERIN		0x00020000
-#	define PLX_EECK			0x01000000
-#	define PLX_EECS			0x02000000
-#	define PLX_EEWD			0x04000000
-#	define PLX_EERD			0x08000000
-
-/*
- *	DMA registers.  Offset is from local side
- */
-#define	PLX_DMA0_MODE		0x100
-#	define PLX_DMA_MODE_WIDTH32	0x00000003
-#	define PLX_DMA_MODE_WAITSTATES(X)	((X)<<2)
-#	define PLX_DMA_MODE_NOREADY	0x00000000
-#	define PLX_DMA_MODE_READY	0x00000040
-#	define PLX_DMA_MODE_NOBTERM	0x00000000
-#	define PLX_DMA_MODE_BTERM	0x00000080
-#	define PLX_DMA_MODE_NOBURST	0x00000000
-#	define PLX_DMA_MODE_BURST	0x00000100
-#	define PLX_DMA_MODE_NOCHAIN	0x00000000
-#	define PLX_DMA_MODE_CHAIN	0x00000200
-#	define PLX_DMA_MODE_DONE_IE	0x00000400
-#	define PLX_DMA_MODE_ADDR_HOLD	0x00000800
-
-#define	PLX_DMA0_PCI_ADDR	0x104
-					/* non-chaining mode PCI address */
-
-#define	PLX_DMA0_LCL_ADDR	0x108
-					/* non-chaining mode local address */
-
-#define	PLX_DMA0_SIZE		0x10C
-					/* non-chaining mode length */
-
-#define	PLX_DMA0_DESCRIPTOR	0x110
-#	define	PLX_DMA_DESC_EOC	0x00000002
-#	define	PLX_DMA_DESC_TC_IE	0x00000004
-#	define	PLX_DMA_DESC_TO_HOST	0x00000008
-#	define	PLX_DMA_DESC_TO_BOARD	0x00000000
-#	define	PLX_DMA_DESC_NEXTADDR	0xFFFFfff0
-
-#define	PLX_DMA1_MODE		0x114
-#define	PLX_DMA1_PCI_ADDR	0x118
-#define	PLX_DMA1_LCL_ADDR	0x11C
-#define	PLX_DMA1_SIZE		0x110
-#define	PLX_DMA1_DESCRIPTOR	0x124
-
-#define	PLX_DMA_CSR		0x128
-#	define PLX_DMA_CSR_0_ENABLE	0x00000001
-#	define PLX_DMA_CSR_0_START	0x00000002
-#	define PLX_DMA_CSR_0_ABORT	0x00000004
-#	define PLX_DMA_CSR_0_CLR_INTR	0x00000008
-#	define PLX_DMA_CSR_0_DONE	0x00000010
-#	define PLX_DMA_CSR_1_ENABLE	0x00000100
-#	define PLX_DMA_CSR_1_START	0x00000200
-#	define PLX_DMA_CSR_1_ABORT	0x00000400
-#	define PLX_DMA_CSR_1_CLR_INTR	0x00000800
-#	define PLX_DMA_CSR_1_DONE	0x00001000
-
-#define	PLX_DMA_ARB0		0x12C
-#	define PLX_DMA_ARB0_LATENCY_T	0x000000FF
-#	define PLX_DMA_ARB0_PAUSE_T	0x0000FF00
-#	define PLX_DMA_ARB0_LATENCY_EN	0x00010000
-#	define PLX_DMA_ARB0_PAUSE_EN	0x00020000
-#	define PLX_DMA_ARB0_BREQ_EN	0x00040000
-#	define PLX_DMA_ARB0_PRI		0x00180000
-#	define PLX_DMA_ARB0_PRI_ROUND	0x00000000
-#	define PLX_DMA_ARB0_PRI_0	0x00080000
-#	define PLX_DMA_ARB0_PRI_1	0x00100000
-
-#define	PLX_DMA_ARB1		0x130
-						/* Chan 0: FIFO DEPTH=16 */
-#	define PLX_DMA_ARB1_0_P2L_LW_TRIG(X)	( ((X)&15) <<  0 )
-#	define PLX_DMA_ARB1_0_L2P_LR_TRIG(X)	( ((X)&15) <<  4 )
-#	define PLX_DMA_ARB1_0_L2P_PW_TRIG(X)	( ((X)&15) <<  8 )
-#	define PLX_DMA_ARB1_0_P2L_PR_TRIG(X)	( ((X)&15) << 12 )
-						/* Chan 1: FIFO DEPTH=8 */
-#	define PLX_DMA_ARB1_1_P2L_LW_TRIG(X)	( ((X)& 7) << 16 )
-#	define PLX_DMA_ARB1_1_L2P_LR_TRIG(X)	( ((X)& 7) << 20 )
-#	define PLX_DMA_ARB1_1_L2P_PW_TRIG(X)	( ((X)& 7) << 24 )
-#	define PLX_DMA_ARB1_1_P2L_PR_TRIG(X)	( ((X)& 7) << 28 )
-
-typedef struct _dmachain
-{
-	ulong		pciaddr;
-	ulong		lcladdr;
-	ulong		len;
-	ulong		next;
-} DMACHAIN;