8390: Move the 8390 related drivers

Moves the drivers for the National Semi-conductor 8390 chipset into
drivers/net/ethernet/8390/ and the necessary Kconfig and Makefile
changes.

CC: Donald Becker <becker@scyld.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Alain Malek <alain.malek@cryogen.com>
CC: Peter De Schrijver <p2@mind.be>
CC: "David Huggins-Daines" <dhd@debian.org>
CC: Wim Dumon <wimpie@kotnet.org>
CC: Yoshinori Sato <ysato@users.sourceforge.jp>
CC: David Hinds <dahinds@users.sourceforge.net>
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1 files changed, 0 insertions, 464 deletions

diff --git a/drivers/net/smc-ultra32.c b/drivers/net/smc-ultra32.c
deleted file mode 100644
index e459c3b2510a..000000000000
--- a/drivers/net/smc-ultra32.c
+++ /dev/null
@@ -1,464 +0,0 @@
-/* 	smc-ultra32.c: An SMC Ultra32 EISA ethernet driver for linux.
-
-Sources:
-
-	This driver is based on (cloned from) the ISA SMC Ultra driver
-	written by Donald Becker. Modifications to support the EISA
-	version of the card by Paul Gortmaker and Leonard N. Zubkoff.
-
-	This software may be used and distributed according to the terms
-	of the GNU General Public License, incorporated herein by reference.
-
-Theory of Operation:
-
-	The SMC Ultra32C card uses the SMC 83c790 chip which is also
-	found on the ISA SMC Ultra cards. It has a shared memory mode of
-	operation that makes it similar to the ISA version of the card.
-	The main difference is that the EISA card has 32KB of RAM, but
-	only an 8KB window into that memory. The EISA card also can be
-	set for a bus-mastering mode of operation via the ECU, but that
-	is not (and probably will never be) supported by this driver.
-	The ECU should be run to enable shared memory and to disable the
-	bus-mastering feature for use with linux.
-
-	By programming the 8390 to use only 8KB RAM, the modifications
-	to the ISA driver can be limited to the probe and initialization
-	code. This allows easy integration of EISA support into the ISA
-	driver. However, the driver development kit from SMC provided the
-	register information for sliding the 8KB window, and hence the 8390
-	is programmed to use the full 32KB RAM.
-
-	Unfortunately this required code changes outside the probe/init
-	routines, and thus we decided to separate the EISA driver from
-	the ISA one. In this way, ISA users don't end up with a larger
-	driver due to the EISA code, and EISA users don't end up with a
-	larger driver due to the ISA EtherEZ PIO code. The driver is
-	similar to the 3c503/16 driver, in that the window must be set
-	back to the 1st 8KB of space for access to the two 8390 Tx slots.
-
-	In testing, using only 8KB RAM (3 Tx / 5 Rx) didn't appear to
-	be a limiting factor, since the EISA bus could get packets off
-	the card fast enough, but having the use of lots of RAM as Rx
-	space is extra insurance if interrupt latencies become excessive.
-
-*/
-
-static const char *version = "smc-ultra32.c: 06/97 v1.00\n";
-
-
-#include <linux/module.h>
-#include <linux/eisa.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-
-#include <asm/io.h>
-#include <asm/system.h>
-
-#include "8390.h"
-
-#define DRV_NAME "smc-ultra32"
-
-static int ultra32_probe1(struct net_device *dev, int ioaddr);
-static int ultra32_open(struct net_device *dev);
-static void ultra32_reset_8390(struct net_device *dev);
-static void ultra32_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
-				 int ring_page);
-static void ultra32_block_input(struct net_device *dev, int count,
-				struct sk_buff *skb, int ring_offset);
-static void ultra32_block_output(struct net_device *dev, int count,
-				 const unsigned char *buf,
-				 const int start_page);
-static int ultra32_close(struct net_device *dev);
-
-#define ULTRA32_CMDREG	0	/* Offset to ASIC command register. */
-#define	 ULTRA32_RESET	0x80	/* Board reset, in ULTRA32_CMDREG. */
-#define	 ULTRA32_MEMENB	0x40	/* Enable the shared memory. */
-#define ULTRA32_NIC_OFFSET 16	/* NIC register offset from the base_addr. */
-#define ULTRA32_IO_EXTENT 32
-#define EN0_ERWCNT		0x08	/* Early receive warning count. */
-
-/*
- * Defines that apply only to the Ultra32 EISA card. Note that
- * "smc" = 10011 01101 00011 = 0x4da3, and hence !smc8010.cfg translates
- * into an EISA ID of 0x1080A34D
- */
-#define ULTRA32_BASE	0xca0
-#define ULTRA32_ID	0x1080a34d
-#define ULTRA32_IDPORT	(-0x20)	/* 0xc80 */
-/* Config regs 1->7 from the EISA !SMC8010.CFG file. */
-#define ULTRA32_CFG1	0x04	/* 0xca4 */
-#define ULTRA32_CFG2	0x05	/* 0xca5 */
-#define ULTRA32_CFG3	(-0x18)	/* 0xc88 */
-#define ULTRA32_CFG4	(-0x17)	/* 0xc89 */
-#define ULTRA32_CFG5	(-0x16)	/* 0xc8a */
-#define ULTRA32_CFG6	(-0x15)	/* 0xc8b */
-#define ULTRA32_CFG7	0x0d	/* 0xcad */
-
-static void cleanup_card(struct net_device *dev)
-{
-	int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET;
-	/* NB: ultra32_close_card() does free_irq */
-	release_region(ioaddr, ULTRA32_IO_EXTENT);
-	iounmap(ei_status.mem);
-}
-
-/*	Probe for the Ultra32.  This looks like a 8013 with the station
-	address PROM at I/O ports <base>+8 to <base>+13, with a checksum
-	following.
-*/
-
-struct net_device * __init ultra32_probe(int unit)
-{
-	struct net_device *dev;
-	int base;
-	int irq;
-	int err = -ENODEV;
-
-	if (!EISA_bus)
-		return ERR_PTR(-ENODEV);
-
-	dev = alloc_ei_netdev();
-
-	if (!dev)
-		return ERR_PTR(-ENOMEM);
-
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-	}
-
-	irq = dev->irq;
-
-	/* EISA spec allows for up to 16 slots, but 8 is typical. */
-	for (base = 0x1000 + ULTRA32_BASE; base < 0x9000; base += 0x1000) {
-		if (ultra32_probe1(dev, base) == 0)
-			break;
-		dev->irq = irq;
-	}
-	if (base >= 0x9000)
-		goto out;
-	err = register_netdev(dev);
-	if (err)
-		goto out1;
-	return dev;
-out1:
-	cleanup_card(dev);
-out:
-	free_netdev(dev);
-	return ERR_PTR(err);
-}
-
-
-static const struct net_device_ops ultra32_netdev_ops = {
-	.ndo_open 		= ultra32_open,
-	.ndo_stop 		= ultra32_close,
-	.ndo_start_xmit		= ei_start_xmit,
-	.ndo_tx_timeout		= ei_tx_timeout,
-	.ndo_get_stats		= ei_get_stats,
-	.ndo_set_multicast_list = ei_set_multicast_list,
-	.ndo_validate_addr	= eth_validate_addr,
-	.ndo_set_mac_address 	= eth_mac_addr,
-	.ndo_change_mtu		= eth_change_mtu,
-#ifdef CONFIG_NET_POLL_CONTROLLER
-	.ndo_poll_controller	= ei_poll,
-#endif
-};
-
-static int __init ultra32_probe1(struct net_device *dev, int ioaddr)
-{
-	int i, edge, media, retval;
-	int checksum = 0;
-	const char *model_name;
-	static unsigned version_printed;
-	/* Values from various config regs. */
-	unsigned char idreg;
-	unsigned char reg4;
-	const char *ifmap[] = {"UTP No Link", "", "UTP/AUI", "UTP/BNC"};
-
-	if (!request_region(ioaddr, ULTRA32_IO_EXTENT, DRV_NAME))
-		return -EBUSY;
-
-	if (inb(ioaddr + ULTRA32_IDPORT) == 0xff ||
-	    inl(ioaddr + ULTRA32_IDPORT) != ULTRA32_ID) {
-		retval = -ENODEV;
-		goto out;
-	}
-
-	media = inb(ioaddr + ULTRA32_CFG7) & 0x03;
-	edge = inb(ioaddr + ULTRA32_CFG5) & 0x08;
-	printk("SMC Ultra32 in EISA Slot %d, Media: %s, %s IRQs.\n",
-		ioaddr >> 12, ifmap[media],
-		(edge ? "Edge Triggered" : "Level Sensitive"));
-
-	idreg = inb(ioaddr + 7);
-	reg4 = inb(ioaddr + 4) & 0x7f;
-
-	/* Check the ID nibble. */
-	if ((idreg & 0xf0) != 0x20) {			/* SMC Ultra */
-		retval = -ENODEV;
-		goto out;
-	}
-
-	/* Select the station address register set. */
-	outb(reg4, ioaddr + 4);
-
-	for (i = 0; i < 8; i++)
-		checksum += inb(ioaddr + 8 + i);
-	if ((checksum & 0xff) != 0xff) {
-		retval = -ENODEV;
-		goto out;
-	}
-
-	if (ei_debug  &&  version_printed++ == 0)
-		printk(version);
-
-	model_name = "SMC Ultra32";
-
-	for (i = 0; i < 6; i++)
-		dev->dev_addr[i] = inb(ioaddr + 8 + i);
-
-	printk("%s: %s at 0x%X, %pM",
-	       dev->name, model_name, ioaddr, dev->dev_addr);
-
-	/* Switch from the station address to the alternate register set and
-	   read the useful registers there. */
-	outb(0x80 | reg4, ioaddr + 4);
-
-	/* Enable FINE16 mode to avoid BIOS ROM width mismatches @ reboot. */
-	outb(0x80 | inb(ioaddr + 0x0c), ioaddr + 0x0c);
-
-	/* Reset RAM addr. */
-	outb(0x00, ioaddr + 0x0b);
-
-	/* Switch back to the station address register set so that the
-	   MS-DOS driver can find the card after a warm boot. */
-	outb(reg4, ioaddr + 4);
-
-	if ((inb(ioaddr + ULTRA32_CFG5) & 0x40) == 0) {
-		printk("\nsmc-ultra32: Card RAM is disabled!  "
-		       "Run EISA config utility.\n");
-		retval = -ENODEV;
-		goto out;
-	}
-	if ((inb(ioaddr + ULTRA32_CFG2) & 0x04) == 0)
-		printk("\nsmc-ultra32: Ignoring Bus-Master enable bit.  "
-		       "Run EISA config utility.\n");
-
-	if (dev->irq < 2) {
-		unsigned char irqmap[] = {0, 9, 3, 5, 7, 10, 11, 15};
-		int irq = irqmap[inb(ioaddr + ULTRA32_CFG5) & 0x07];
-		if (irq == 0) {
-			printk(", failed to detect IRQ line.\n");
-			retval = -EAGAIN;
-			goto out;
-		}
-		dev->irq = irq;
-	}
-
-	/* The 8390 isn't at the base address, so fake the offset */
-	dev->base_addr = ioaddr + ULTRA32_NIC_OFFSET;
-
-	/* Save RAM address in the unused reg0 to avoid excess inb's. */
-	ei_status.reg0 = inb(ioaddr + ULTRA32_CFG3) & 0xfc;
-
-	dev->mem_start =  0xc0000 + ((ei_status.reg0 & 0x7c) << 11);
-
-	ei_status.name = model_name;
-	ei_status.word16 = 1;
-	ei_status.tx_start_page = 0;
-	ei_status.rx_start_page = TX_PAGES;
-	/* All Ultra32 cards have 32KB memory with an 8KB window. */
-	ei_status.stop_page = 128;
-
-	ei_status.mem = ioremap(dev->mem_start, 0x2000);
-	if (!ei_status.mem) {
-		printk(", failed to ioremap.\n");
-		retval = -ENOMEM;
-		goto out;
-	}
-	dev->mem_end = dev->mem_start + 0x1fff;
-
-	printk(", IRQ %d, 32KB memory, 8KB window at 0x%lx-0x%lx.\n",
-	       dev->irq, dev->mem_start, dev->mem_end);
-	ei_status.block_input = &ultra32_block_input;
-	ei_status.block_output = &ultra32_block_output;
-	ei_status.get_8390_hdr = &ultra32_get_8390_hdr;
-	ei_status.reset_8390 = &ultra32_reset_8390;
-
-	dev->netdev_ops = &ultra32_netdev_ops;
-	NS8390_init(dev, 0);
-
-	return 0;
-out:
-	release_region(ioaddr, ULTRA32_IO_EXTENT);
-	return retval;
-}
-
-static int ultra32_open(struct net_device *dev)
-{
-	int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* ASIC addr */
-	int irq_flags = (inb(ioaddr + ULTRA32_CFG5) & 0x08) ? 0 : IRQF_SHARED;
-	int retval;
-
-	retval = request_irq(dev->irq, ei_interrupt, irq_flags, dev->name, dev);
-	if (retval)
-		return retval;
-
-	outb(ULTRA32_MEMENB, ioaddr); /* Enable Shared Memory. */
-	outb(0x80, ioaddr + ULTRA32_CFG6); /* Enable Interrupts. */
-	outb(0x84, ioaddr + 5);	/* Enable MEM16 & Disable Bus Master. */
-	outb(0x01, ioaddr + 6);	/* Enable Interrupts. */
-	/* Set the early receive warning level in window 0 high enough not
-	   to receive ERW interrupts. */
-	outb_p(E8390_NODMA+E8390_PAGE0, dev->base_addr);
-	outb(0xff, dev->base_addr + EN0_ERWCNT);
-	ei_open(dev);
-	return 0;
-}
-
-static int ultra32_close(struct net_device *dev)
-{
-	int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* CMDREG */
-
-	netif_stop_queue(dev);
-
-	if (ei_debug > 1)
-		printk("%s: Shutting down ethercard.\n", dev->name);
-
-	outb(0x00, ioaddr + ULTRA32_CFG6); /* Disable Interrupts. */
-	outb(0x00, ioaddr + 6);		/* Disable interrupts. */
-	free_irq(dev->irq, dev);
-
-	NS8390_init(dev, 0);
-
-	return 0;
-}
-
-static void ultra32_reset_8390(struct net_device *dev)
-{
-	int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* ASIC base addr */
-
-	outb(ULTRA32_RESET, ioaddr);
-	if (ei_debug > 1) printk("resetting Ultra32, t=%ld...", jiffies);
-	ei_status.txing = 0;
-
-	outb(ULTRA32_MEMENB, ioaddr); /* Enable Shared Memory. */
-	outb(0x80, ioaddr + ULTRA32_CFG6); /* Enable Interrupts. */
-	outb(0x84, ioaddr + 5);	/* Enable MEM16 & Disable Bus Master. */
-	outb(0x01, ioaddr + 6);	/* Enable Interrupts. */
-	if (ei_debug > 1) printk("reset done\n");
-}
-
-/* Grab the 8390 specific header. Similar to the block_input routine, but
-   we don't need to be concerned with ring wrap as the header will be at
-   the start of a page, so we optimize accordingly. */
-
-static void ultra32_get_8390_hdr(struct net_device *dev,
-				 struct e8390_pkt_hdr *hdr,
-				 int ring_page)
-{
-	void __iomem *hdr_start = ei_status.mem + ((ring_page & 0x1f) << 8);
-	unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3;
-
-	/* Select correct 8KB Window. */
-	outb(ei_status.reg0 | ((ring_page & 0x60) >> 5), RamReg);
-
-#ifdef __BIG_ENDIAN
-	/* Officially this is what we are doing, but the readl() is faster */
-	/* unfortunately it isn't endian aware of the struct               */
-	memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr));
-	hdr->count = le16_to_cpu(hdr->count);
-#else
-	((unsigned int*)hdr)[0] = readl(hdr_start);
-#endif
-}
-
-/* Block input and output are easy on shared memory ethercards, the only
-   complication is when the ring buffer wraps, or in this case, when a
-   packet spans an 8KB boundary. Note that the current 8KB segment is
-   already set by the get_8390_hdr routine. */
-
-static void ultra32_block_input(struct net_device *dev,
-				int count,
-				struct sk_buff *skb,
-				int ring_offset)
-{
-	void __iomem *xfer_start = ei_status.mem + (ring_offset & 0x1fff);
-	unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3;
-
-	if ((ring_offset & ~0x1fff) != ((ring_offset + count - 1) & ~0x1fff)) {
-		int semi_count = 8192 - (ring_offset & 0x1FFF);
-		memcpy_fromio(skb->data, xfer_start, semi_count);
-		count -= semi_count;
-		if (ring_offset < 96*256) {
-			/* Select next 8KB Window. */
-			ring_offset += semi_count;
-			outb(ei_status.reg0 | ((ring_offset & 0x6000) >> 13), RamReg);
-			memcpy_fromio(skb->data + semi_count, ei_status.mem, count);
-		} else {
-			/* Select first 8KB Window. */
-			outb(ei_status.reg0, RamReg);
-			memcpy_fromio(skb->data + semi_count, ei_status.mem + TX_PAGES * 256, count);
-		}
-	} else {
-		memcpy_fromio(skb->data, xfer_start, count);
-	}
-}
-
-static void ultra32_block_output(struct net_device *dev,
-				 int count,
-				 const unsigned char *buf,
-				 int start_page)
-{
-	void __iomem *xfer_start = ei_status.mem + (start_page<<8);
-	unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3;
-
-	/* Select first 8KB Window. */
-	outb(ei_status.reg0, RamReg);
-
-	memcpy_toio(xfer_start, buf, count);
-}
-
-#ifdef MODULE
-#define MAX_ULTRA32_CARDS   4	/* Max number of Ultra cards per module */
-static struct net_device *dev_ultra[MAX_ULTRA32_CARDS];
-
-MODULE_DESCRIPTION("SMC Ultra32 EISA ethernet driver");
-MODULE_LICENSE("GPL");
-
-int __init init_module(void)
-{
-	int this_dev, found = 0;
-
-	for (this_dev = 0; this_dev < MAX_ULTRA32_CARDS; this_dev++) {
-		struct net_device *dev = ultra32_probe(-1);
-		if (IS_ERR(dev))
-			break;
-		dev_ultra[found++] = dev;
-	}
-	if (found)
-		return 0;
-	printk(KERN_WARNING "smc-ultra32.c: No SMC Ultra32 found.\n");
-	return -ENXIO;
-}
-
-void __exit cleanup_module(void)
-{
-	int this_dev;
-
-	for (this_dev = 0; this_dev < MAX_ULTRA32_CARDS; this_dev++) {
-		struct net_device *dev = dev_ultra[this_dev];
-		if (dev) {
-			unregister_netdev(dev);
-			cleanup_card(dev);
-			free_netdev(dev);
-		}
-	}
-}
-#endif /* MODULE */
-