diff options
| author | Ajay Singh <ajay.kathat@microchip.com> | 2024-06-13 16:06:40 +0200 |
|---|---|---|
| committer | Kalle Valo <kvalo@kernel.org> | 2024-06-18 12:23:15 +0200 |
| commit | 70ed0bdab1ca17aef6731e2c146b69050ff447f6 (patch) | |
| tree | 1a5b56b3bec623e40cbd58538af0d10e086f317a /drivers/net/wireless/microchip/wilc1000 | |
| parent | wifi: wl18xx: allow firmwares > 8.9.0.x.58 (diff) | |
| download | linux-70ed0bdab1ca17aef6731e2c146b69050ff447f6.tar.xz linux-70ed0bdab1ca17aef6731e2c146b69050ff447f6.zip | |
wifi: wilc1000: disable power sequencer
Driver systematically disables some power mechanism each time it starts the
chip firmware (so mostly when interface is brought up). This has a negative
impact on some specific scenarios when the chip is exposed as a
hotpluggable SDIO card (eg: WILC1000 SD):
- when executing suspend/resume sequence while interface has been brought
up
- rebooting the platform while module is plugged and interface has been
brought up
Those scenarios lead to mmc core trying to initialize again the chip which
is now unresponsive (because of the power sequencer setting), so it fails
in mmc_rescan->mmc_attach_sdio and enter a failure loop while trying to
send CMD5:
mmc0: error -110 whilst initialising SDIO card
mmc0: error -110 whilst initialising SDIO card
mmc0: error -110 whilst initialising SDIO card
[...]
Preventing the driver from disabling this "power sequencer" fixes those
enumeration issues without affecting nominal operations.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-1-c2f766d0988c@bootlin.com
Diffstat (limited to 'drivers/net/wireless/microchip/wilc1000')
| -rw-r--r-- | drivers/net/wireless/microchip/wilc1000/sdio.c | 15 | ||||
| -rw-r--r-- | drivers/net/wireless/microchip/wilc1000/wlan.h | 1 |
2 files changed, 0 insertions, 16 deletions
diff --git a/drivers/net/wireless/microchip/wilc1000/sdio.c b/drivers/net/wireless/microchip/wilc1000/sdio.c index e6e20c86b791..6461a3ec0120 100644 --- a/drivers/net/wireless/microchip/wilc1000/sdio.c +++ b/drivers/net/wireless/microchip/wilc1000/sdio.c @@ -907,27 +907,12 @@ static int wilc_sdio_sync_ext(struct wilc *wilc, int nint) { struct sdio_func *func = dev_to_sdio_func(wilc->dev); struct wilc_sdio *sdio_priv = wilc->bus_data; - u32 reg; if (nint > MAX_NUM_INT) { dev_err(&func->dev, "Too many interrupts (%d)...\n", nint); return -EINVAL; } - /** - * Disable power sequencer - **/ - if (wilc_sdio_read_reg(wilc, WILC_MISC, ®)) { - dev_err(&func->dev, "Failed read misc reg...\n"); - return -EINVAL; - } - - reg &= ~BIT(8); - if (wilc_sdio_write_reg(wilc, WILC_MISC, reg)) { - dev_err(&func->dev, "Failed write misc reg...\n"); - return -EINVAL; - } - if (sdio_priv->irq_gpio) { u32 reg; int ret, i; diff --git a/drivers/net/wireless/microchip/wilc1000/wlan.h b/drivers/net/wireless/microchip/wilc1000/wlan.h index d72a0a81bbda..dd2fb3c2f06a 100644 --- a/drivers/net/wireless/microchip/wilc1000/wlan.h +++ b/drivers/net/wireless/microchip/wilc1000/wlan.h @@ -56,7 +56,6 @@ #define WILC_HOST_RX_CTRL (WILC_PERIPH_REG_BASE + 0x80) #define WILC_HOST_RX_EXTRA_SIZE (WILC_PERIPH_REG_BASE + 0x84) #define WILC_HOST_TX_CTRL_1 (WILC_PERIPH_REG_BASE + 0x88) -#define WILC_MISC (WILC_PERIPH_REG_BASE + 0x428) #define WILC_INTR_REG_BASE (WILC_PERIPH_REG_BASE + 0xa00) #define WILC_INTR_ENABLE WILC_INTR_REG_BASE #define WILC_INTR2_ENABLE (WILC_INTR_REG_BASE + 4) |