of/pci: move of_irq_map_pci() into generic code

There is a tiny difference between PPC32 and PPC64. Microblaze uses the
PPC32 variant.

Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
[grant.likely@secretlab.ca: Added comment to #endif, moved documentation
	block to function implementation, fixed for non ppc and microblaze
	compiles]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

1 files changed, 91 insertions, 0 deletions

diff --git a/drivers/of/of_pci.c b/drivers/of/of_pci.c
new file mode 100644
index 000000000000..314535fa32c1
--- /dev/null
+++ b/drivers/of/of_pci.c
@@ -0,0 +1,91 @@
+#include <linux/kernel.h>
+#include <linux/of_pci.h>
+#include <asm/prom.h>
+
+/**
+ * of_irq_map_pci - Resolve the interrupt for a PCI device
+ * @pdev:       the device whose interrupt is to be resolved
+ * @out_irq:    structure of_irq filled by this function
+ *
+ * This function resolves the PCI interrupt for a given PCI device. If a
+ * device-node exists for a given pci_dev, it will use normal OF tree
+ * walking. If not, it will implement standard swizzling and walk up the
+ * PCI tree until an device-node is found, at which point it will finish
+ * resolving using the OF tree walking.
+ */
+int of_irq_map_pci(struct pci_dev *pdev, struct of_irq *out_irq)
+{
+	struct device_node *dn, *ppnode;
+	struct pci_dev *ppdev;
+	u32 lspec;
+	__be32 lspec_be;
+	__be32 laddr[3];
+	u8 pin;
+	int rc;
+
+	/* Check if we have a device node, if yes, fallback to standard
+	 * device tree parsing
+	 */
+	dn = pci_device_to_OF_node(pdev);
+	if (dn) {
+		rc = of_irq_map_one(dn, 0, out_irq);
+		if (!rc)
+			return rc;
+	}
+
+	/* Ok, we don't, time to have fun. Let's start by building up an
+	 * interrupt spec.  we assume #interrupt-cells is 1, which is standard
+	 * for PCI. If you do different, then don't use that routine.
+	 */
+	rc = pci_read_config_byte(pdev, PCI_INTERRUPT_PIN, &pin);
+	if (rc != 0)
+		return rc;
+	/* No pin, exit */
+	if (pin == 0)
+		return -ENODEV;
+
+	/* Now we walk up the PCI tree */
+	lspec = pin;
+	for (;;) {
+		/* Get the pci_dev of our parent */
+		ppdev = pdev->bus->self;
+
+		/* Ouch, it's a host bridge... */
+		if (ppdev == NULL) {
+			ppnode = pci_bus_to_OF_node(pdev->bus);
+
+			/* No node for host bridge ? give up */
+			if (ppnode == NULL)
+				return -EINVAL;
+		} else {
+			/* We found a P2P bridge, check if it has a node */
+			ppnode = pci_device_to_OF_node(ppdev);
+		}
+
+		/* Ok, we have found a parent with a device-node, hand over to
+		 * the OF parsing code.
+		 * We build a unit address from the linux device to be used for
+		 * resolution. Note that we use the linux bus number which may
+		 * not match your firmware bus numbering.
+		 * Fortunately, in most cases, interrupt-map-mask doesn't
+		 * include the bus number as part of the matching.
+		 * You should still be careful about that though if you intend
+		 * to rely on this function (you ship  a firmware that doesn't
+		 * create device nodes for all PCI devices).
+		 */
+		if (ppnode)
+			break;
+
+		/* We can only get here if we hit a P2P bridge with no node,
+		 * let's do standard swizzling and try again
+		 */
+		lspec = pci_swizzle_interrupt_pin(pdev, lspec);
+		pdev = ppdev;
+	}
+
+	lspec_be = cpu_to_be32(lspec);
+	laddr[0] = cpu_to_be32((pdev->bus->number << 16) | (pdev->devfn << 8));
+	laddr[1]  = laddr[2] = cpu_to_be32(0);
+	return of_irq_map_raw(ppnode, &lspec_be, 1, laddr, out_irq);
+}
+EXPORT_SYMBOL_GPL(of_irq_map_pci);