PCI: designware: Return data directly from dw_pcie_readl_rc()

dw_pcie_readl_rc() reads a u32 value.  Previously we stored that value in
space supplied by the caller.  Return the u32 value directly instead.

This makes the calling code read better and makes it obvious that the
caller need not initialize the storage.  In the following example it isn't
clear whether "val" is initialized before being used:

  dw_pcie_readl_rc(pp, PCI_COMMAND, &val);
  if (val & PCI_COMMAND_MEMORY)
    ...

No functional change intended.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

1 files changed, 10 insertions, 10 deletions

diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c
index 12afce19890b..1f6bd6d42874 100644
--- a/drivers/pci/host/pcie-designware.c
+++ b/drivers/pci/host/pcie-designware.c
@@ -115,12 +115,12 @@ int dw_pcie_cfg_write(void __iomem *addr, int size, u32 val)
 	return PCIBIOS_SUCCESSFUL;
 }
 
-static inline void dw_pcie_readl_rc(struct pcie_port *pp, u32 reg, u32 *val)
+static inline u32 dw_pcie_readl_rc(struct pcie_port *pp, u32 reg)
 {
 	if (pp->ops->readl_rc)
-		pp->ops->readl_rc(pp, pp->dbi_base + reg, val);
-	else
-		*val = readl(pp->dbi_base + reg);
+		return pp->ops->readl_rc(pp, pp->dbi_base + reg);
+
+	return readl(pp->dbi_base + reg);
 }
 
 static inline void dw_pcie_writel_rc(struct pcie_port *pp, u32 val, u32 reg)
@@ -169,7 +169,7 @@ static void dw_pcie_prog_outbound_atu(struct pcie_port *pp, int index,
 	 * Make sure ATU enable takes effect before any subsequent config
 	 * and I/O accesses.
 	 */
-	dw_pcie_readl_rc(pp, PCIE_ATU_CR2, &val);
+	val = dw_pcie_readl_rc(pp, PCIE_ATU_CR2);
 }
 
 static struct irq_chip dw_msi_irq_chip = {
@@ -720,7 +720,7 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
 	u32 val;
 
 	/* set the number of lanes */
-	dw_pcie_readl_rc(pp, PCIE_PORT_LINK_CONTROL, &val);
+	val = dw_pcie_readl_rc(pp, PCIE_PORT_LINK_CONTROL);
 	val &= ~PORT_LINK_MODE_MASK;
 	switch (pp->lanes) {
 	case 1:
@@ -742,7 +742,7 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
 	dw_pcie_writel_rc(pp, val, PCIE_PORT_LINK_CONTROL);
 
 	/* set link width speed control register */
-	dw_pcie_readl_rc(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, &val);
+	val = dw_pcie_readl_rc(pp, PCIE_LINK_WIDTH_SPEED_CONTROL);
 	val &= ~PORT_LOGIC_LINK_WIDTH_MASK;
 	switch (pp->lanes) {
 	case 1:
@@ -765,19 +765,19 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
 	dw_pcie_writel_rc(pp, 0x00000000, PCI_BASE_ADDRESS_1);
 
 	/* setup interrupt pins */
-	dw_pcie_readl_rc(pp, PCI_INTERRUPT_LINE, &val);
+	val = dw_pcie_readl_rc(pp, PCI_INTERRUPT_LINE);
 	val &= 0xffff00ff;
 	val |= 0x00000100;
 	dw_pcie_writel_rc(pp, val, PCI_INTERRUPT_LINE);
 
 	/* setup bus numbers */
-	dw_pcie_readl_rc(pp, PCI_PRIMARY_BUS, &val);
+	val = dw_pcie_readl_rc(pp, PCI_PRIMARY_BUS);
 	val &= 0xff000000;
 	val |= 0x00010100;
 	dw_pcie_writel_rc(pp, val, PCI_PRIMARY_BUS);
 
 	/* setup command register */
-	dw_pcie_readl_rc(pp, PCI_COMMAND, &val);
+	val = dw_pcie_readl_rc(pp, PCI_COMMAND);
 	val &= 0xffff0000;
 	val |= PCI_COMMAND_IO | PCI_COMMAND_MEMORY |
 		PCI_COMMAND_MASTER | PCI_COMMAND_SERR;