diff options
author | Paolo Valente <paolo.valente@linaro.org> | 2017-04-12 18:23:11 +0200 |
---|---|---|
committer | Jens Axboe <axboe@fb.com> | 2017-04-19 16:30:26 +0200 |
commit | c074170e65995706be78e8c57ed2017c638d5464 (patch) | |
tree | 380cebbd58df1c0ecfb033e1b19755cf829e2530 /drivers/pcmcia/pd6729.h | |
parent | block, bfq: modify the peak-rate estimator (diff) | |
download | linux-c074170e65995706be78e8c57ed2017c638d5464.tar.xz linux-c074170e65995706be78e8c57ed2017c638d5464.zip |
block, bfq: add more fairness with writes and slow processes
This patch deals with two sources of unfairness, which can also cause
high latencies and throughput loss. The first source is related to
write requests. Write requests tend to starve read requests, basically
because, on one side, writes are slower than reads, whereas, on the
other side, storage devices confuse schedulers by deceptively
signaling the completion of write requests immediately after receiving
them. This patch addresses this issue by just throttling writes. In
particular, after a write request is dispatched for a queue, the
budget of the queue is decremented by the number of sectors to write,
multiplied by an (over)charge coefficient. The value of the
coefficient is the result of our tuning with different devices.
The second source of unfairness has to do with slowness detection:
when the in-service queue is expired, BFQ also controls whether the
queue has been "too slow", i.e., has consumed its last-assigned budget
at such a low rate that it would have been impossible to consume all
of this budget within the maximum time slice T_max (Subsec. 3.5 in
[1]). In this case, the queue is always (over)charged the whole
budget, to reduce its utilization of the device. Both this overcharge
and the slowness-detection criterion may cause unfairness.
First, always charging a full budget to a slow queue is too coarse. It
is much more accurate, and this patch lets BFQ do so, to charge an
amount of service 'equivalent' to the amount of time during which the
queue has been in service. As explained in more detail in the comments
on the code, this enables BFQ to provide time fairness among slow
queues.
Secondly, because of ZBR, a queue may be deemed as slow when its
associated process is performing I/O on the slowest zones of a
disk. However, unless the process is truly too slow, not reducing the
disk utilization of the queue is more profitable in terms of disk
throughput than the opposite. A similar problem is caused by logical
block mapping on non-rotational devices. For this reason, this patch
lets a queue be charged time, and not budget, only if the queue has
consumed less than 2/3 of its assigned budget. As an additional,
important benefit, this tolerance allows BFQ to preserve enough
elasticity to still perform bandwidth, and not time, distribution with
little unlucky or quasi-sequential processes.
Finally, for the same reasons as above, this patch makes slowness
detection itself much less harsh: a queue is deemed slow only if it
has consumed its budget at less than half of the peak rate.
[1] P. Valente and M. Andreolini, "Improving Application
Responsiveness with the BFQ Disk I/O Scheduler", Proceedings of
the 5th Annual International Systems and Storage Conference
(SYSTOR '12), June 2012.
Slightly extended version:
http://algogroup.unimore.it/people/paolo/disk_sched/bfq-v1-suite-
results.pdf
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Diffstat (limited to 'drivers/pcmcia/pd6729.h')
0 files changed, 0 insertions, 0 deletions