Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Olof Johansson:
 "Various driver updates for platforms:

   - A larger set of work on Tegra 2/3 around memory controller and
     regulator features, some fuse cleanups, etc..

   - MMP platform drivers, in particular for USB PHY, and other smaller
     additions.

   - Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
     and ASV (adaptive voltage), allowing the platform to run at more
     optimal operating points.

   - Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas

   - Clock/reset control driver for TI/OMAP

   - Meson-A1 reset controller support

   - Qualcomm sdm845 and sda845 SoC IDs for socinfo"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
  firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
  soc: fsl: add RCPM driver
  dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
  memory: tegra: Consolidate registers definition into common header
  memory: tegra: Ensure timing control debug features are disabled
  memory: tegra: Introduce Tegra30 EMC driver
  memory: tegra: Do not handle error from wait_for_completion_timeout()
  memory: tegra: Increase handshake timeout on Tegra20
  memory: tegra: Print a brief info message about EMC timings
  memory: tegra: Pre-configure debug register on Tegra20
  memory: tegra: Include io.h instead of iopoll.h
  memory: tegra: Adapt for Tegra20 clock driver changes
  memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
  memory: tegra: Add gr2d and gr3d to DRM IOMMU group
  memory: tegra: Set DMA mask based on supported address bits
  soc: at91: Add Atmel SFR SN (Serial Number) support
  memory: atmel-ebi: switch to SPDX license identifiers
  memory: atmel-ebi: move NUM_CS definition inside EBI driver
  soc: mediatek: Refactor bus protection control
  soc: mediatek: Refactor sram control
  ...

3 files changed, 303 insertions, 0 deletions

diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
index 4053ba6cd0fb..005e02dd4a91 100644
--- a/drivers/phy/marvell/Kconfig
+++ b/drivers/phy/marvell/Kconfig
@@ -103,3 +103,14 @@ config PHY_PXA_USB
 	  The PHY driver will be used by Marvell udc/ehci/otg driver.
 
 	  To compile this driver as a module, choose M here.
+
+config PHY_MMP3_USB
+	tristate "Marvell MMP3 USB PHY Driver"
+	depends on MACH_MMP3_DT || COMPILE_TEST
+	select GENERIC_PHY
+	help
+	  Enable this to support Marvell MMP3 USB PHY driver for Marvell
+	  SoC. This driver will do the PHY initialization and shutdown.
+	  The PHY driver will be used by Marvell udc/ehci/otg driver.
+
+	  To compile this driver as a module, choose M here.
diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
index 434eb9ca6cc3..5a106b1549f4 100644
--- a/drivers/phy/marvell/Makefile
+++ b/drivers/phy/marvell/Makefile
@@ -2,6 +2,7 @@
 obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
 obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
 obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
+obj-$(CONFIG_PHY_MMP3_USB)		+= phy-mmp3-usb.o
 obj-$(CONFIG_PHY_MVEBU_A3700_COMPHY)	+= phy-mvebu-a3700-comphy.o
 obj-$(CONFIG_PHY_MVEBU_A3700_UTMI)	+= phy-mvebu-a3700-utmi.o
 obj-$(CONFIG_PHY_MVEBU_A38X_COMPHY)	+= phy-armada38x-comphy.o
diff --git a/drivers/phy/marvell/phy-mmp3-usb.c b/drivers/phy/marvell/phy-mmp3-usb.c
new file mode 100644
index 000000000000..499869595a58
--- /dev/null
+++ b/drivers/phy/marvell/phy-mmp3-usb.c
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2011 Marvell International Ltd. All rights reserved.
+ * Copyright (C) 2018,2019 Lubomir Rintel <lkundrak@v3.sk>
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/soc/mmp/cputype.h>
+
+#define USB2_PLL_REG0		0x4
+#define USB2_PLL_REG1		0x8
+#define USB2_TX_REG0		0x10
+#define USB2_TX_REG1		0x14
+#define USB2_TX_REG2		0x18
+#define USB2_RX_REG0		0x20
+#define USB2_RX_REG1		0x24
+#define USB2_RX_REG2		0x28
+#define USB2_ANA_REG0		0x30
+#define USB2_ANA_REG1		0x34
+#define USB2_ANA_REG2		0x38
+#define USB2_DIG_REG0		0x3C
+#define USB2_DIG_REG1		0x40
+#define USB2_DIG_REG2		0x44
+#define USB2_DIG_REG3		0x48
+#define USB2_TEST_REG0		0x4C
+#define USB2_TEST_REG1		0x50
+#define USB2_TEST_REG2		0x54
+#define USB2_CHARGER_REG0	0x58
+#define USB2_OTG_REG0		0x5C
+#define USB2_PHY_MON0		0x60
+#define USB2_RESETVE_REG0	0x64
+#define USB2_ICID_REG0		0x78
+#define USB2_ICID_REG1		0x7C
+
+/* USB2_PLL_REG0 */
+
+/* This is for Ax stepping */
+#define USB2_PLL_FBDIV_SHIFT_MMP3		0
+#define USB2_PLL_FBDIV_MASK_MMP3		(0xFF << 0)
+
+#define USB2_PLL_REFDIV_SHIFT_MMP3		8
+#define USB2_PLL_REFDIV_MASK_MMP3		(0xF << 8)
+
+#define USB2_PLL_VDD12_SHIFT_MMP3		12
+#define USB2_PLL_VDD18_SHIFT_MMP3		14
+
+/* This is for B0 stepping */
+#define USB2_PLL_FBDIV_SHIFT_MMP3_B0		0
+#define USB2_PLL_REFDIV_SHIFT_MMP3_B0		9
+#define USB2_PLL_VDD18_SHIFT_MMP3_B0		14
+#define USB2_PLL_FBDIV_MASK_MMP3_B0		0x01FF
+#define USB2_PLL_REFDIV_MASK_MMP3_B0		0x3E00
+
+#define USB2_PLL_CAL12_SHIFT_MMP3		0
+#define USB2_PLL_CALI12_MASK_MMP3		(0x3 << 0)
+
+#define USB2_PLL_VCOCAL_START_SHIFT_MMP3	2
+
+#define USB2_PLL_KVCO_SHIFT_MMP3		4
+#define USB2_PLL_KVCO_MASK_MMP3			(0x7<<4)
+
+#define USB2_PLL_ICP_SHIFT_MMP3			8
+#define USB2_PLL_ICP_MASK_MMP3			(0x7<<8)
+
+#define USB2_PLL_LOCK_BYPASS_SHIFT_MMP3		12
+
+#define USB2_PLL_PU_PLL_SHIFT_MMP3		13
+#define USB2_PLL_PU_PLL_MASK			(0x1 << 13)
+
+#define USB2_PLL_READY_MASK_MMP3		(0x1 << 15)
+
+/* USB2_TX_REG0 */
+#define USB2_TX_IMPCAL_VTH_SHIFT_MMP3		8
+#define USB2_TX_IMPCAL_VTH_MASK_MMP3		(0x7 << 8)
+
+#define USB2_TX_RCAL_START_SHIFT_MMP3		13
+
+/* USB2_TX_REG1 */
+#define USB2_TX_CK60_PHSEL_SHIFT_MMP3		0
+#define USB2_TX_CK60_PHSEL_MASK_MMP3		(0xf << 0)
+
+#define USB2_TX_AMP_SHIFT_MMP3			4
+#define USB2_TX_AMP_MASK_MMP3			(0x7 << 4)
+
+#define USB2_TX_VDD12_SHIFT_MMP3		8
+#define USB2_TX_VDD12_MASK_MMP3			(0x3 << 8)
+
+/* USB2_TX_REG2 */
+#define USB2_TX_DRV_SLEWRATE_SHIFT		10
+
+/* USB2_RX_REG0 */
+#define USB2_RX_SQ_THRESH_SHIFT_MMP3		4
+#define USB2_RX_SQ_THRESH_MASK_MMP3		(0xf << 4)
+
+#define USB2_RX_SQ_LENGTH_SHIFT_MMP3		10
+#define USB2_RX_SQ_LENGTH_MASK_MMP3		(0x3 << 10)
+
+/* USB2_ANA_REG1*/
+#define USB2_ANA_PU_ANA_SHIFT_MMP3		14
+
+/* USB2_OTG_REG0 */
+#define USB2_OTG_PU_OTG_SHIFT_MMP3		3
+
+struct mmp3_usb_phy {
+	struct phy *phy;
+	void __iomem *base;
+};
+
+static unsigned int u2o_get(void __iomem *base, unsigned int offset)
+{
+	return readl_relaxed(base + offset);
+}
+
+static void u2o_set(void __iomem *base, unsigned int offset,
+		unsigned int value)
+{
+	u32 reg;
+
+	reg = readl_relaxed(base + offset);
+	reg |= value;
+	writel_relaxed(reg, base + offset);
+	readl_relaxed(base + offset);
+}
+
+static void u2o_clear(void __iomem *base, unsigned int offset,
+		unsigned int value)
+{
+	u32 reg;
+
+	reg = readl_relaxed(base + offset);
+	reg &= ~value;
+	writel_relaxed(reg, base + offset);
+	readl_relaxed(base + offset);
+}
+
+static int mmp3_usb_phy_init(struct phy *phy)
+{
+	struct mmp3_usb_phy *mmp3_usb_phy = phy_get_drvdata(phy);
+	void __iomem *base = mmp3_usb_phy->base;
+
+	if (cpu_is_mmp3_a0()) {
+		u2o_clear(base, USB2_PLL_REG0, (USB2_PLL_FBDIV_MASK_MMP3
+			| USB2_PLL_REFDIV_MASK_MMP3));
+		u2o_set(base, USB2_PLL_REG0,
+			0xd << USB2_PLL_REFDIV_SHIFT_MMP3
+			| 0xf0 << USB2_PLL_FBDIV_SHIFT_MMP3);
+	} else if (cpu_is_mmp3_b0()) {
+		u2o_clear(base, USB2_PLL_REG0, USB2_PLL_REFDIV_MASK_MMP3_B0
+			| USB2_PLL_FBDIV_MASK_MMP3_B0);
+		u2o_set(base, USB2_PLL_REG0,
+			0xd << USB2_PLL_REFDIV_SHIFT_MMP3_B0
+			| 0xf0 << USB2_PLL_FBDIV_SHIFT_MMP3_B0);
+	} else {
+		dev_err(&phy->dev, "unsupported silicon revision\n");
+		return -ENODEV;
+	}
+
+	u2o_clear(base, USB2_PLL_REG1, USB2_PLL_PU_PLL_MASK
+		| USB2_PLL_ICP_MASK_MMP3
+		| USB2_PLL_KVCO_MASK_MMP3
+		| USB2_PLL_CALI12_MASK_MMP3);
+	u2o_set(base, USB2_PLL_REG1, 1 << USB2_PLL_PU_PLL_SHIFT_MMP3
+		| 1 << USB2_PLL_LOCK_BYPASS_SHIFT_MMP3
+		| 3 << USB2_PLL_ICP_SHIFT_MMP3
+		| 3 << USB2_PLL_KVCO_SHIFT_MMP3
+		| 3 << USB2_PLL_CAL12_SHIFT_MMP3);
+
+	u2o_clear(base, USB2_TX_REG0, USB2_TX_IMPCAL_VTH_MASK_MMP3);
+	u2o_set(base, USB2_TX_REG0, 2 << USB2_TX_IMPCAL_VTH_SHIFT_MMP3);
+
+	u2o_clear(base, USB2_TX_REG1, USB2_TX_VDD12_MASK_MMP3
+		| USB2_TX_AMP_MASK_MMP3
+		| USB2_TX_CK60_PHSEL_MASK_MMP3);
+	u2o_set(base, USB2_TX_REG1, 3 << USB2_TX_VDD12_SHIFT_MMP3
+		| 4 << USB2_TX_AMP_SHIFT_MMP3
+		| 4 << USB2_TX_CK60_PHSEL_SHIFT_MMP3);
+
+	u2o_clear(base, USB2_TX_REG2, 3 << USB2_TX_DRV_SLEWRATE_SHIFT);
+	u2o_set(base, USB2_TX_REG2, 2 << USB2_TX_DRV_SLEWRATE_SHIFT);
+
+	u2o_clear(base, USB2_RX_REG0, USB2_RX_SQ_THRESH_MASK_MMP3);
+	u2o_set(base, USB2_RX_REG0, 0xa << USB2_RX_SQ_THRESH_SHIFT_MMP3);
+
+	u2o_set(base, USB2_ANA_REG1, 0x1 << USB2_ANA_PU_ANA_SHIFT_MMP3);
+
+	u2o_set(base, USB2_OTG_REG0, 0x1 << USB2_OTG_PU_OTG_SHIFT_MMP3);
+
+	return 0;
+}
+
+static int mmp3_usb_phy_calibrate(struct phy *phy)
+{
+	struct mmp3_usb_phy *mmp3_usb_phy = phy_get_drvdata(phy);
+	void __iomem *base = mmp3_usb_phy->base;
+	int loops;
+
+	/*
+	 * PLL VCO and TX Impedance Calibration Timing:
+	 *
+	 *                _____________________________________
+	 * PU  __________|
+	 *                        _____________________________
+	 * VCOCAL START _________|
+	 *                                 ___
+	 * REG_RCAL_START ________________|   |________|_______
+	 *               | 200us | 400us  | 40| 400us  | USB PHY READY
+	 */
+
+	udelay(200);
+	u2o_set(base, USB2_PLL_REG1, 1 << USB2_PLL_VCOCAL_START_SHIFT_MMP3);
+	udelay(400);
+	u2o_set(base, USB2_TX_REG0, 1 << USB2_TX_RCAL_START_SHIFT_MMP3);
+	udelay(40);
+	u2o_clear(base, USB2_TX_REG0, 1 << USB2_TX_RCAL_START_SHIFT_MMP3);
+	udelay(400);
+
+	loops = 0;
+	while ((u2o_get(base, USB2_PLL_REG1) & USB2_PLL_READY_MASK_MMP3) == 0) {
+		mdelay(1);
+		loops++;
+		if (loops > 100) {
+			dev_err(&phy->dev, "PLL_READY not set after 100mS.\n");
+			return -ETIMEDOUT;
+		}
+	}
+
+	return 0;
+}
+
+static const struct phy_ops mmp3_usb_phy_ops = {
+	.init		= mmp3_usb_phy_init,
+	.calibrate	= mmp3_usb_phy_calibrate,
+	.owner		= THIS_MODULE,
+};
+
+static const struct of_device_id mmp3_usb_phy_of_match[] = {
+	{ .compatible = "marvell,mmp3-usb-phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mmp3_usb_phy_of_match);
+
+static int mmp3_usb_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *resource;
+	struct mmp3_usb_phy *mmp3_usb_phy;
+	struct phy_provider *provider;
+
+	mmp3_usb_phy = devm_kzalloc(dev, sizeof(*mmp3_usb_phy), GFP_KERNEL);
+	if (!mmp3_usb_phy)
+		return -ENOMEM;
+
+	resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mmp3_usb_phy->base = devm_ioremap_resource(dev, resource);
+	if (IS_ERR(mmp3_usb_phy->base)) {
+		dev_err(dev, "failed to remap PHY regs\n");
+		return PTR_ERR(mmp3_usb_phy->base);
+	}
+
+	mmp3_usb_phy->phy = devm_phy_create(dev, NULL, &mmp3_usb_phy_ops);
+	if (IS_ERR(mmp3_usb_phy->phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(mmp3_usb_phy->phy);
+	}
+
+	phy_set_drvdata(mmp3_usb_phy->phy, mmp3_usb_phy);
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(provider)) {
+		dev_err(dev, "failed to register PHY provider\n");
+		return PTR_ERR(provider);
+	}
+
+	return 0;
+}
+
+static struct platform_driver mmp3_usb_phy_driver = {
+	.probe		= mmp3_usb_phy_probe,
+	.driver		= {
+		.name	= "mmp3-usb-phy",
+		.of_match_table = mmp3_usb_phy_of_match,
+	},
+};
+module_platform_driver(mmp3_usb_phy_driver);
+
+MODULE_AUTHOR("Lubomir Rintel <lkundrak@v3.sk>");
+MODULE_DESCRIPTION("Marvell MMP3 USB PHY Driver");
+MODULE_LICENSE("GPL v2");