ARM: OMAP: SmartReflex: Move smartreflex driver to drivers/

After a clean-up of the interfaces the OMAP Smartreflex IP driver is now a
generic driver. Move it to drivers/power/avs/.

The build is controlled by the following Kconfig options:
 . CONFIG_POWER_AVS: general knob for Adaptive Voltage Scaling support,
 . CONFIG_POWER_AVS_OMAP: AVS(Adaptive Voltage Scaling)
   support on OMAP containing the version 1 or version 2 of the SmartReflex IP,
 . CONFIG_POWER_AVS_OMAP_CLASS3: Class 3 implementation of Smartreflex.

Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

5 files changed, 1142 insertions, 0 deletions

diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 99dc29f2f2f2..d416773771ef 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -308,3 +308,5 @@ config AB8500_BATTERY_THERM_ON_BATCTRL
 	  Say Y to enable battery temperature measurements using
 	  thermistor connected on BATCTRL ADC.
 endif # POWER_SUPPLY
+
+source "drivers/power/avs/Kconfig"
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index b6b243416c0e..ee58afb1e71f 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -43,4 +43,5 @@ obj-$(CONFIG_CHARGER_GPIO)	+= gpio-charger.o
 obj-$(CONFIG_CHARGER_MANAGER)	+= charger-manager.o
 obj-$(CONFIG_CHARGER_MAX8997)	+= max8997_charger.o
 obj-$(CONFIG_CHARGER_MAX8998)	+= max8998_charger.o
+obj-$(CONFIG_POWER_AVS)		+= avs/
 obj-$(CONFIG_CHARGER_SMB347)	+= smb347-charger.o
diff --git a/drivers/power/avs/Kconfig b/drivers/power/avs/Kconfig
new file mode 100644
index 000000000000..18493f7a8f6f
--- /dev/null
+++ b/drivers/power/avs/Kconfig
@@ -0,0 +1,12 @@
+menuconfig POWER_AVS
+	tristate "Adaptive Voltage Scaling class support"
+	help
+	  AVS is a power management technique which finely controls the
+	  operating voltage of a device in order to optimize (i.e. reduce)
+	  its power consumption.
+	  At a given operating point the voltage is adapted depending on
+	  static factors (chip manufacturing process) and dynamic factors
+	  (temperature depending performance).
+	  AVS is also called SmartReflex on OMAP devices.
+
+	  Say Y here to enable Adaptive Voltage Scaling class support.
diff --git a/drivers/power/avs/Makefile b/drivers/power/avs/Makefile
new file mode 100644
index 000000000000..0843386a6c19
--- /dev/null
+++ b/drivers/power/avs/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_POWER_AVS_OMAP)		+= smartreflex.o
diff --git a/drivers/power/avs/smartreflex.c b/drivers/power/avs/smartreflex.c
new file mode 100644
index 000000000000..44efc6e202af
--- /dev/null
+++ b/drivers/power/avs/smartreflex.c
@@ -0,0 +1,1126 @@
+/*
+ * OMAP SmartReflex Voltage Control
+ *
+ * Author: Thara Gopinath	<thara@ti.com>
+ *
+ * Copyright (C) 2012 Texas Instruments, Inc.
+ * Thara Gopinath <thara@ti.com>
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Kalle Jokiniemi
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ * Lesly A M <x0080970@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/pm_runtime.h>
+#include <linux/power/smartreflex.h>
+
+#define SMARTREFLEX_NAME_LEN	16
+#define NVALUE_NAME_LEN		40
+#define SR_DISABLE_TIMEOUT	200
+
+/* sr_list contains all the instances of smartreflex module */
+static LIST_HEAD(sr_list);
+
+static struct omap_sr_class_data *sr_class;
+static struct omap_sr_pmic_data *sr_pmic_data;
+static struct dentry		*sr_dbg_dir;
+
+static inline void sr_write_reg(struct omap_sr *sr, unsigned offset, u32 value)
+{
+	__raw_writel(value, (sr->base + offset));
+}
+
+static inline void sr_modify_reg(struct omap_sr *sr, unsigned offset, u32 mask,
+					u32 value)
+{
+	u32 reg_val;
+
+	/*
+	 * Smartreflex error config register is special as it contains
+	 * certain status bits which if written a 1 into means a clear
+	 * of those bits. So in order to make sure no accidental write of
+	 * 1 happens to those status bits, do a clear of them in the read
+	 * value. This mean this API doesn't rewrite values in these bits
+	 * if they are currently set, but does allow the caller to write
+	 * those bits.
+	 */
+	if (sr->ip_type == SR_TYPE_V1 && offset == ERRCONFIG_V1)
+		mask |= ERRCONFIG_STATUS_V1_MASK;
+	else if (sr->ip_type == SR_TYPE_V2 && offset == ERRCONFIG_V2)
+		mask |= ERRCONFIG_VPBOUNDINTST_V2;
+
+	reg_val = __raw_readl(sr->base + offset);
+	reg_val &= ~mask;
+
+	value &= mask;
+
+	reg_val |= value;
+
+	__raw_writel(reg_val, (sr->base + offset));
+}
+
+static inline u32 sr_read_reg(struct omap_sr *sr, unsigned offset)
+{
+	return __raw_readl(sr->base + offset);
+}
+
+static struct omap_sr *_sr_lookup(struct voltagedomain *voltdm)
+{
+	struct omap_sr *sr_info;
+
+	if (!voltdm) {
+		pr_err("%s: Null voltage domain passed!\n", __func__);
+		return ERR_PTR(-EINVAL);
+	}
+
+	list_for_each_entry(sr_info, &sr_list, node) {
+		if (voltdm == sr_info->voltdm)
+			return sr_info;
+	}
+
+	return ERR_PTR(-ENODATA);
+}
+
+static irqreturn_t sr_interrupt(int irq, void *data)
+{
+	struct omap_sr *sr_info = data;
+	u32 status = 0;
+
+	switch (sr_info->ip_type) {
+	case SR_TYPE_V1:
+		/* Read the status bits */
+		status = sr_read_reg(sr_info, ERRCONFIG_V1);
+
+		/* Clear them by writing back */
+		sr_write_reg(sr_info, ERRCONFIG_V1, status);
+		break;
+	case SR_TYPE_V2:
+		/* Read the status bits */
+		status = sr_read_reg(sr_info, IRQSTATUS);
+
+		/* Clear them by writing back */
+		sr_write_reg(sr_info, IRQSTATUS, status);
+		break;
+	default:
+		dev_err(&sr_info->pdev->dev, "UNKNOWN IP type %d\n",
+			sr_info->ip_type);
+		return IRQ_NONE;
+	}
+
+	if (sr_class->notify)
+		sr_class->notify(sr_info, status);
+
+	return IRQ_HANDLED;
+}
+
+static void sr_set_clk_length(struct omap_sr *sr)
+{
+	struct clk *sys_ck;
+	u32 sys_clk_speed;
+
+	if (cpu_is_omap34xx())
+		sys_ck = clk_get(NULL, "sys_ck");
+	else
+		sys_ck = clk_get(NULL, "sys_clkin_ck");
+
+	if (IS_ERR(sys_ck)) {
+		dev_err(&sr->pdev->dev, "%s: unable to get sys clk\n",
+			__func__);
+		return;
+	}
+
+	sys_clk_speed = clk_get_rate(sys_ck);
+	clk_put(sys_ck);
+
+	switch (sys_clk_speed) {
+	case 12000000:
+		sr->clk_length = SRCLKLENGTH_12MHZ_SYSCLK;
+		break;
+	case 13000000:
+		sr->clk_length = SRCLKLENGTH_13MHZ_SYSCLK;
+		break;
+	case 19200000:
+		sr->clk_length = SRCLKLENGTH_19MHZ_SYSCLK;
+		break;
+	case 26000000:
+		sr->clk_length = SRCLKLENGTH_26MHZ_SYSCLK;
+		break;
+	case 38400000:
+		sr->clk_length = SRCLKLENGTH_38MHZ_SYSCLK;
+		break;
+	default:
+		dev_err(&sr->pdev->dev, "%s: Invalid sysclk value: %d\n",
+			__func__, sys_clk_speed);
+		break;
+	}
+}
+
+static void sr_set_regfields(struct omap_sr *sr)
+{
+	/*
+	 * For time being these values are defined in smartreflex.h
+	 * and populated during init. May be they can be moved to board
+	 * file or pmic specific data structure. In that case these structure
+	 * fields will have to be populated using the pdata or pmic structure.
+	 */
+	if (cpu_is_omap34xx() || cpu_is_omap44xx()) {
+		sr->err_weight = OMAP3430_SR_ERRWEIGHT;
+		sr->err_maxlimit = OMAP3430_SR_ERRMAXLIMIT;
+		sr->accum_data = OMAP3430_SR_ACCUMDATA;
+		if (!(strcmp(sr->name, "smartreflex_mpu_iva"))) {
+			sr->senn_avgweight = OMAP3430_SR1_SENNAVGWEIGHT;
+			sr->senp_avgweight = OMAP3430_SR1_SENPAVGWEIGHT;
+		} else {
+			sr->senn_avgweight = OMAP3430_SR2_SENNAVGWEIGHT;
+			sr->senp_avgweight = OMAP3430_SR2_SENPAVGWEIGHT;
+		}
+	}
+}
+
+static void sr_start_vddautocomp(struct omap_sr *sr)
+{
+	if (!sr_class || !(sr_class->enable) || !(sr_class->configure)) {
+		dev_warn(&sr->pdev->dev,
+			"%s: smartreflex class driver not registered\n",
+			__func__);
+		return;
+	}
+
+	if (!sr_class->enable(sr))
+		sr->autocomp_active = true;
+}
+
+static void sr_stop_vddautocomp(struct omap_sr *sr)
+{
+	if (!sr_class || !(sr_class->disable)) {
+		dev_warn(&sr->pdev->dev,
+			"%s: smartreflex class driver not registered\n",
+			__func__);
+		return;
+	}
+
+	if (sr->autocomp_active) {
+		sr_class->disable(sr, 1);
+		sr->autocomp_active = false;
+	}
+}
+
+/*
+ * This function handles the intializations which have to be done
+ * only when both sr device and class driver regiter has
+ * completed. This will be attempted to be called from both sr class
+ * driver register and sr device intializtion API's. Only one call
+ * will ultimately succeed.
+ *
+ * Currently this function registers interrupt handler for a particular SR
+ * if smartreflex class driver is already registered and has
+ * requested for interrupts and the SR interrupt line in present.
+ */
+static int sr_late_init(struct omap_sr *sr_info)
+{
+	struct omap_sr_data *pdata = sr_info->pdev->dev.platform_data;
+	struct resource *mem;
+	int ret = 0;
+
+	if (sr_class->notify && sr_class->notify_flags && sr_info->irq) {
+		ret = request_irq(sr_info->irq, sr_interrupt,
+				  0, sr_info->name, sr_info);
+		if (ret)
+			goto error;
+		disable_irq(sr_info->irq);
+	}
+
+	if (pdata && pdata->enable_on_init)
+		sr_start_vddautocomp(sr_info);
+
+	return ret;
+
+error:
+	iounmap(sr_info->base);
+	mem = platform_get_resource(sr_info->pdev, IORESOURCE_MEM, 0);
+	release_mem_region(mem->start, resource_size(mem));
+	list_del(&sr_info->node);
+	dev_err(&sr_info->pdev->dev, "%s: ERROR in registering"
+		"interrupt handler. Smartreflex will"
+		"not function as desired\n", __func__);
+	kfree(sr_info);
+
+	return ret;
+}
+
+static void sr_v1_disable(struct omap_sr *sr)
+{
+	int timeout = 0;
+	int errconf_val = ERRCONFIG_MCUACCUMINTST | ERRCONFIG_MCUVALIDINTST |
+			ERRCONFIG_MCUBOUNDINTST;
+
+	/* Enable MCUDisableAcknowledge interrupt */
+	sr_modify_reg(sr, ERRCONFIG_V1,
+			ERRCONFIG_MCUDISACKINTEN, ERRCONFIG_MCUDISACKINTEN);
+
+	/* SRCONFIG - disable SR */
+	sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0);
+
+	/* Disable all other SR interrupts and clear the status as needed */
+	if (sr_read_reg(sr, ERRCONFIG_V1) & ERRCONFIG_VPBOUNDINTST_V1)
+		errconf_val |= ERRCONFIG_VPBOUNDINTST_V1;
+	sr_modify_reg(sr, ERRCONFIG_V1,
+			(ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN |
+			ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_VPBOUNDINTEN_V1),
+			errconf_val);
+
+	/*
+	 * Wait for SR to be disabled.
+	 * wait until ERRCONFIG.MCUDISACKINTST = 1. Typical latency is 1us.
+	 */
+	sr_test_cond_timeout((sr_read_reg(sr, ERRCONFIG_V1) &
+			     ERRCONFIG_MCUDISACKINTST), SR_DISABLE_TIMEOUT,
+			     timeout);
+
+	if (timeout >= SR_DISABLE_TIMEOUT)
+		dev_warn(&sr->pdev->dev, "%s: Smartreflex disable timedout\n",
+			__func__);
+
+	/* Disable MCUDisableAcknowledge interrupt & clear pending interrupt */
+	sr_modify_reg(sr, ERRCONFIG_V1, ERRCONFIG_MCUDISACKINTEN,
+			ERRCONFIG_MCUDISACKINTST);
+}
+
+static void sr_v2_disable(struct omap_sr *sr)
+{
+	int timeout = 0;
+
+	/* Enable MCUDisableAcknowledge interrupt */
+	sr_write_reg(sr, IRQENABLE_SET, IRQENABLE_MCUDISABLEACKINT);
+
+	/* SRCONFIG - disable SR */
+	sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0);
+
+	/*
+	 * Disable all other SR interrupts and clear the status
+	 * write to status register ONLY on need basis - only if status
+	 * is set.
+	 */
+	if (sr_read_reg(sr, ERRCONFIG_V2) & ERRCONFIG_VPBOUNDINTST_V2)
+		sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2,
+			ERRCONFIG_VPBOUNDINTST_V2);
+	else
+		sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2,
+				0x0);
+	sr_write_reg(sr, IRQENABLE_CLR, (IRQENABLE_MCUACCUMINT |
+			IRQENABLE_MCUVALIDINT |
+			IRQENABLE_MCUBOUNDSINT));
+	sr_write_reg(sr, IRQSTATUS, (IRQSTATUS_MCUACCUMINT |
+			IRQSTATUS_MCVALIDINT |
+			IRQSTATUS_MCBOUNDSINT));
+
+	/*
+	 * Wait for SR to be disabled.
+	 * wait until IRQSTATUS.MCUDISACKINTST = 1. Typical latency is 1us.
+	 */
+	sr_test_cond_timeout((sr_read_reg(sr, IRQSTATUS) &
+			     IRQSTATUS_MCUDISABLEACKINT), SR_DISABLE_TIMEOUT,
+			     timeout);
+
+	if (timeout >= SR_DISABLE_TIMEOUT)
+		dev_warn(&sr->pdev->dev, "%s: Smartreflex disable timedout\n",
+			__func__);
+
+	/* Disable MCUDisableAcknowledge interrupt & clear pending interrupt */
+	sr_write_reg(sr, IRQENABLE_CLR, IRQENABLE_MCUDISABLEACKINT);
+	sr_write_reg(sr, IRQSTATUS, IRQSTATUS_MCUDISABLEACKINT);
+}
+
+static struct omap_sr_nvalue_table *sr_retrieve_nvalue_row(
+				struct omap_sr *sr, u32 efuse_offs)
+{
+	int i;
+
+	if (!sr->nvalue_table) {
+		dev_warn(&sr->pdev->dev, "%s: Missing ntarget value table\n",
+			__func__);
+		return NULL;
+	}
+
+	for (i = 0; i < sr->nvalue_count; i++) {
+		if (sr->nvalue_table[i].efuse_offs == efuse_offs)
+			return &sr->nvalue_table[i];
+	}
+
+	return NULL;
+}
+
+/* Public Functions */
+
+/**
+ * sr_configure_errgen() - Configures the smrtreflex to perform AVS using the
+ *			 error generator module.
+ * @voltdm:	VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * configure the error generator module inside the smartreflex module.
+ * SR settings if using the ERROR module inside Smartreflex.
+ * SR CLASS 3 by default uses only the ERROR module where as
+ * SR CLASS 2 can choose between ERROR module and MINMAXAVG
+ * module. Returns 0 on success and error value in case of failure.
+ */
+int sr_configure_errgen(struct voltagedomain *voltdm)
+{
+	u32 sr_config, sr_errconfig, errconfig_offs;
+	u32 vpboundint_en, vpboundint_st;
+	u32 senp_en = 0, senn_en = 0;
+	u8 senp_shift, senn_shift;
+	struct omap_sr *sr = _sr_lookup(voltdm);
+
+	if (IS_ERR(sr)) {
+		pr_warning("%s: omap_sr struct for voltdm not found\n",	__func__);
+		return PTR_ERR(sr);
+	}
+
+	if (!sr->clk_length)
+		sr_set_clk_length(sr);
+
+	senp_en = sr->senp_mod;
+	senn_en = sr->senn_mod;
+
+	sr_config = (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) |
+		SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN;
+
+	switch (sr->ip_type) {
+	case SR_TYPE_V1:
+		sr_config |= SRCONFIG_DELAYCTRL;
+		senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT;
+		senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT;
+		errconfig_offs = ERRCONFIG_V1;
+		vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1;
+		vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1;
+		break;
+	case SR_TYPE_V2:
+		senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT;
+		senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT;
+		errconfig_offs = ERRCONFIG_V2;
+		vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2;
+		vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2;
+		break;
+	default:
+		dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+			"module without specifying the ip\n", __func__);
+		return -EINVAL;
+	}
+
+	sr_config |= ((senn_en << senn_shift) | (senp_en << senp_shift));
+	sr_write_reg(sr, SRCONFIG, sr_config);
+	sr_errconfig = (sr->err_weight << ERRCONFIG_ERRWEIGHT_SHIFT) |
+		(sr->err_maxlimit << ERRCONFIG_ERRMAXLIMIT_SHIFT) |
+		(sr->err_minlimit <<  ERRCONFIG_ERRMINLIMIT_SHIFT);
+	sr_modify_reg(sr, errconfig_offs, (SR_ERRWEIGHT_MASK |
+		SR_ERRMAXLIMIT_MASK | SR_ERRMINLIMIT_MASK),
+		sr_errconfig);
+
+	/* Enabling the interrupts if the ERROR module is used */
+	sr_modify_reg(sr, errconfig_offs, (vpboundint_en | vpboundint_st),
+		      vpboundint_en);
+
+	return 0;
+}
+
+/**
+ * sr_disable_errgen() - Disables SmartReflex AVS module's errgen component
+ * @voltdm:	VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * disable the error generator module inside the smartreflex module.
+ *
+ * Returns 0 on success and error value in case of failure.
+ */
+int sr_disable_errgen(struct voltagedomain *voltdm)
+{
+	u32 errconfig_offs;
+	u32 vpboundint_en, vpboundint_st;
+	struct omap_sr *sr = _sr_lookup(voltdm);
+
+	if (IS_ERR(sr)) {
+		pr_warning("%s: omap_sr struct for voltdm not found\n",	__func__);
+		return PTR_ERR(sr);
+	}
+
+	switch (sr->ip_type) {
+	case SR_TYPE_V1:
+		errconfig_offs = ERRCONFIG_V1;
+		vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1;
+		vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1;
+		break;
+	case SR_TYPE_V2:
+		errconfig_offs = ERRCONFIG_V2;
+		vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2;
+		vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2;
+		break;
+	default:
+		dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+			"module without specifying the ip\n", __func__);
+		return -EINVAL;
+	}
+
+	/* Disable the interrupts of ERROR module */
+	sr_modify_reg(sr, errconfig_offs, vpboundint_en | vpboundint_st, 0);
+
+	/* Disable the Sensor and errorgen */
+	sr_modify_reg(sr, SRCONFIG, SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN, 0);
+
+	return 0;
+}
+
+/**
+ * sr_configure_minmax() - Configures the smrtreflex to perform AVS using the
+ *			 minmaxavg module.
+ * @voltdm:	VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * configure the minmaxavg module inside the smartreflex module.
+ * SR settings if using the ERROR module inside Smartreflex.
+ * SR CLASS 3 by default uses only the ERROR module where as
+ * SR CLASS 2 can choose between ERROR module and MINMAXAVG
+ * module. Returns 0 on success and error value in case of failure.
+ */
+int sr_configure_minmax(struct voltagedomain *voltdm)
+{
+	u32 sr_config, sr_avgwt;
+	u32 senp_en = 0, senn_en = 0;
+	u8 senp_shift, senn_shift;
+	struct omap_sr *sr = _sr_lookup(voltdm);
+
+	if (IS_ERR(sr)) {
+		pr_warning("%s: omap_sr struct for voltdm not found\n",	__func__);
+		return PTR_ERR(sr);
+	}
+
+	if (!sr->clk_length)
+		sr_set_clk_length(sr);
+
+	senp_en = sr->senp_mod;
+	senn_en = sr->senn_mod;
+
+	sr_config = (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) |
+		SRCONFIG_SENENABLE |
+		(sr->accum_data << SRCONFIG_ACCUMDATA_SHIFT);
+
+	switch (sr->ip_type) {
+	case SR_TYPE_V1:
+		sr_config |= SRCONFIG_DELAYCTRL;
+		senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT;
+		senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT;
+		break;
+	case SR_TYPE_V2:
+		senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT;
+		senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT;
+		break;
+	default:
+		dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+			"module without specifying the ip\n", __func__);
+		return -EINVAL;
+	}
+
+	sr_config |= ((senn_en << senn_shift) | (senp_en << senp_shift));
+	sr_write_reg(sr, SRCONFIG, sr_config);
+	sr_avgwt = (sr->senp_avgweight << AVGWEIGHT_SENPAVGWEIGHT_SHIFT) |
+		(sr->senn_avgweight << AVGWEIGHT_SENNAVGWEIGHT_SHIFT);
+	sr_write_reg(sr, AVGWEIGHT, sr_avgwt);
+
+	/*
+	 * Enabling the interrupts if MINMAXAVG module is used.
+	 * TODO: check if all the interrupts are mandatory
+	 */
+	switch (sr->ip_type) {
+	case SR_TYPE_V1:
+		sr_modify_reg(sr, ERRCONFIG_V1,
+			(ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN |
+			ERRCONFIG_MCUBOUNDINTEN),
+			(ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUACCUMINTST |
+			 ERRCONFIG_MCUVALIDINTEN | ERRCONFIG_MCUVALIDINTST |
+			 ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_MCUBOUNDINTST));
+		break;
+	case SR_TYPE_V2:
+		sr_write_reg(sr, IRQSTATUS,
+			IRQSTATUS_MCUACCUMINT | IRQSTATUS_MCVALIDINT |
+			IRQSTATUS_MCBOUNDSINT | IRQSTATUS_MCUDISABLEACKINT);
+		sr_write_reg(sr, IRQENABLE_SET,
+			IRQENABLE_MCUACCUMINT | IRQENABLE_MCUVALIDINT |
+			IRQENABLE_MCUBOUNDSINT | IRQENABLE_MCUDISABLEACKINT);
+		break;
+	default:
+		dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+			"module without specifying the ip\n", __func__);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * sr_enable() - Enables the smartreflex module.
+ * @voltdm:	VDD pointer to which the SR module to be configured belongs to.
+ * @volt:	The voltage at which the Voltage domain associated with
+ *		the smartreflex module is operating at.
+ *		This is required only to program the correct Ntarget value.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * enable a smartreflex module. Returns 0 on success. Returns error
+ * value if the voltage passed is wrong or if ntarget value is wrong.
+ */
+int sr_enable(struct voltagedomain *voltdm, unsigned long volt)
+{
+	struct omap_volt_data *volt_data;
+	struct omap_sr *sr = _sr_lookup(voltdm);
+	struct omap_sr_nvalue_table *nvalue_row;
+	int ret;
+
+	if (IS_ERR(sr)) {
+		pr_warning("%s: omap_sr struct for voltdm not found\n",	__func__);
+		return PTR_ERR(sr);
+	}
+
+	volt_data = omap_voltage_get_voltdata(sr->voltdm, volt);
+
+	if (IS_ERR(volt_data)) {
+		dev_warn(&sr->pdev->dev, "%s: Unable to get voltage table"
+			"for nominal voltage %ld\n", __func__, volt);
+		return PTR_ERR(volt_data);
+	}
+
+	nvalue_row = sr_retrieve_nvalue_row(sr, volt_data->sr_efuse_offs);
+
+	if (!nvalue_row) {
+		dev_warn(&sr->pdev->dev, "%s: failure getting SR data for this voltage %ld\n",
+			 __func__, volt);
+		return -ENODATA;
+	}
+
+	/* errminlimit is opp dependent and hence linked to voltage */
+	sr->err_minlimit = nvalue_row->errminlimit;
+
+	pm_runtime_get_sync(&sr->pdev->dev);
+
+	/* Check if SR is already enabled. If yes do nothing */
+	if (sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE)
+		return 0;
+
+	/* Configure SR */
+	ret = sr_class->configure(sr);
+	if (ret)
+		return ret;
+
+	sr_write_reg(sr, NVALUERECIPROCAL, nvalue_row->nvalue);
+
+	/* SRCONFIG - enable SR */
+	sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, SRCONFIG_SRENABLE);
+	return 0;
+}
+
+/**
+ * sr_disable() - Disables the smartreflex module.
+ * @voltdm:	VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * disable a smartreflex module.
+ */
+void sr_disable(struct voltagedomain *voltdm)
+{
+	struct omap_sr *sr = _sr_lookup(voltdm);
+
+	if (IS_ERR(sr)) {
+		pr_warning("%s: omap_sr struct for voltdm not found\n",	__func__);
+		return;
+	}
+
+	/* Check if SR clocks are already disabled. If yes do nothing */
+	if (pm_runtime_suspended(&sr->pdev->dev))
+		return;
+
+	/*
+	 * Disable SR if only it is indeed enabled. Else just
+	 * disable the clocks.
+	 */
+	if (sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE) {
+		switch (sr->ip_type) {
+		case SR_TYPE_V1:
+			sr_v1_disable(sr);
+			break;
+		case SR_TYPE_V2:
+			sr_v2_disable(sr);
+			break;
+		default:
+			dev_err(&sr->pdev->dev, "UNKNOWN IP type %d\n",
+				sr->ip_type);
+		}
+	}
+
+	pm_runtime_put_sync_suspend(&sr->pdev->dev);
+}
+
+/**
+ * sr_register_class() - API to register a smartreflex class parameters.
+ * @class_data:	The structure containing various sr class specific data.
+ *
+ * This API is to be called by the smartreflex class driver to register itself
+ * with the smartreflex driver during init. Returns 0 on success else the
+ * error value.
+ */
+int sr_register_class(struct omap_sr_class_data *class_data)
+{
+	struct omap_sr *sr_info;
+
+	if (!class_data) {
+		pr_warning("%s:, Smartreflex class data passed is NULL\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	if (sr_class) {
+		pr_warning("%s: Smartreflex class driver already registered\n",
+			__func__);
+		return -EBUSY;
+	}
+
+	sr_class = class_data;
+
+	/*
+	 * Call into late init to do intializations that require
+	 * both sr driver and sr class driver to be initiallized.
+	 */
+	list_for_each_entry(sr_info, &sr_list, node)
+		sr_late_init(sr_info);
+
+	return 0;
+}
+
+/**
+ * omap_sr_enable() -  API to enable SR clocks and to call into the
+ *			registered smartreflex class enable API.
+ * @voltdm:	VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the kernel in order to enable
+ * a particular smartreflex module. This API will do the initial
+ * configurations to turn on the smartreflex module and in turn call
+ * into the registered smartreflex class enable API.
+ */
+void omap_sr_enable(struct voltagedomain *voltdm)
+{
+	struct omap_sr *sr = _sr_lookup(voltdm);
+
+	if (IS_ERR(sr)) {
+		pr_warning("%s: omap_sr struct for voltdm not found\n",	__func__);
+		return;
+	}
+
+	if (!sr->autocomp_active)
+		return;
+
+	if (!sr_class || !(sr_class->enable) || !(sr_class->configure)) {
+		dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not"
+			"registered\n", __func__);
+		return;
+	}
+
+	sr_class->enable(sr);
+}
+
+/**
+ * omap_sr_disable() - API to disable SR without resetting the voltage
+ *			processor voltage
+ * @voltdm:	VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the kernel in order to disable
+ * a particular smartreflex module. This API will in turn call
+ * into the registered smartreflex class disable API. This API will tell
+ * the smartreflex class disable not to reset the VP voltage after
+ * disabling smartreflex.
+ */
+void omap_sr_disable(struct voltagedomain *voltdm)
+{
+	struct omap_sr *sr = _sr_lookup(voltdm);
+
+	if (IS_ERR(sr)) {
+		pr_warning("%s: omap_sr struct for voltdm not found\n",	__func__);
+		return;
+	}
+
+	if (!sr->autocomp_active)
+		return;
+
+	if (!sr_class || !(sr_class->disable)) {
+		dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not"
+			"registered\n", __func__);
+		return;
+	}
+
+	sr_class->disable(sr, 0);
+}
+
+/**
+ * omap_sr_disable_reset_volt() - API to disable SR and reset the
+ *				voltage processor voltage
+ * @voltdm:	VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the kernel in order to disable
+ * a particular smartreflex module. This API will in turn call
+ * into the registered smartreflex class disable API. This API will tell
+ * the smartreflex class disable to reset the VP voltage after
+ * disabling smartreflex.
+ */
+void omap_sr_disable_reset_volt(struct voltagedomain *voltdm)
+{
+	struct omap_sr *sr = _sr_lookup(voltdm);
+
+	if (IS_ERR(sr)) {
+		pr_warning("%s: omap_sr struct for voltdm not found\n",	__func__);
+		return;
+	}
+
+	if (!sr->autocomp_active)
+		return;
+
+	if (!sr_class || !(sr_class->disable)) {
+		dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not"
+			"registered\n", __func__);
+		return;
+	}
+
+	sr_class->disable(sr, 1);
+}
+
+/**
+ * omap_sr_register_pmic() - API to register pmic specific info.
+ * @pmic_data:	The structure containing pmic specific data.
+ *
+ * This API is to be called from the PMIC specific code to register with
+ * smartreflex driver pmic specific info. Currently the only info required
+ * is the smartreflex init on the PMIC side.
+ */
+void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data)
+{
+	if (!pmic_data) {
+		pr_warning("%s: Trying to register NULL PMIC data structure"
+			"with smartreflex\n", __func__);
+		return;
+	}
+
+	sr_pmic_data = pmic_data;
+}
+
+/* PM Debug FS entries to enable and disable smartreflex. */
+static int omap_sr_autocomp_show(void *data, u64 *val)
+{
+	struct omap_sr *sr_info = data;
+
+	if (!sr_info) {
+		pr_warning("%s: omap_sr struct not found\n", __func__);
+		return -EINVAL;
+	}
+
+	*val = sr_info->autocomp_active;
+
+	return 0;
+}
+
+static int omap_sr_autocomp_store(void *data, u64 val)
+{
+	struct omap_sr *sr_info = data;
+
+	if (!sr_info) {
+		pr_warning("%s: omap_sr struct not found\n", __func__);
+		return -EINVAL;
+	}
+
+	/* Sanity check */
+	if (val > 1) {
+		pr_warning("%s: Invalid argument %lld\n", __func__, val);
+		return -EINVAL;
+	}
+
+	/* control enable/disable only if there is a delta in value */
+	if (sr_info->autocomp_active != val) {
+		if (!val)
+			sr_stop_vddautocomp(sr_info);
+		else
+			sr_start_vddautocomp(sr_info);
+	}
+
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(pm_sr_fops, omap_sr_autocomp_show,
+			omap_sr_autocomp_store, "%llu\n");
+
+static int __init omap_sr_probe(struct platform_device *pdev)
+{
+	struct omap_sr *sr_info;
+	struct omap_sr_data *pdata = pdev->dev.platform_data;
+	struct resource *mem, *irq;
+	struct dentry *nvalue_dir;
+	int i, ret = 0;
+
+	sr_info = kzalloc(sizeof(struct omap_sr), GFP_KERNEL);
+	if (!sr_info) {
+		dev_err(&pdev->dev, "%s: unable to allocate sr_info\n",
+			__func__);
+		return -ENOMEM;
+	}
+
+	platform_set_drvdata(pdev, sr_info);
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
+		ret = -EINVAL;
+		goto err_free_devinfo;
+	}
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!mem) {
+		dev_err(&pdev->dev, "%s: no mem resource\n", __func__);
+		ret = -ENODEV;
+		goto err_free_devinfo;
+	}
+
+	mem = request_mem_region(mem->start, resource_size(mem),
+					dev_name(&pdev->dev));
+	if (!mem) {
+		dev_err(&pdev->dev, "%s: no mem region\n", __func__);
+		ret = -EBUSY;
+		goto err_free_devinfo;
+	}
+
+	irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_irq_safe(&pdev->dev);
+
+	sr_info->name = kasprintf(GFP_KERNEL, "%s", pdata->name);
+	if (!sr_info->name) {
+		dev_err(&pdev->dev, "%s: Unable to alloc SR instance name\n",
+			__func__);
+		ret = -ENOMEM;
+		goto err_release_region;
+	}
+
+	sr_info->pdev = pdev;
+	sr_info->srid = pdev->id;
+	sr_info->voltdm = pdata->voltdm;
+	sr_info->nvalue_table = pdata->nvalue_table;
+	sr_info->nvalue_count = pdata->nvalue_count;
+	sr_info->senn_mod = pdata->senn_mod;
+	sr_info->senp_mod = pdata->senp_mod;
+	sr_info->autocomp_active = false;
+	sr_info->ip_type = pdata->ip_type;
+	sr_info->base = ioremap(mem->start, resource_size(mem));
+	if (!sr_info->base) {
+		dev_err(&pdev->dev, "%s: ioremap fail\n", __func__);
+		ret = -ENOMEM;
+		goto err_release_region;
+	}
+
+	if (irq)
+		sr_info->irq = irq->start;
+
+	sr_set_clk_length(sr_info);
+	sr_set_regfields(sr_info);
+
+	list_add(&sr_info->node, &sr_list);
+
+	/*
+	 * Call into late init to do intializations that require
+	 * both sr driver and sr class driver to be initiallized.
+	 */
+	if (sr_class) {
+		ret = sr_late_init(sr_info);
+		if (ret) {
+			pr_warning("%s: Error in SR late init\n", __func__);
+			goto err_iounmap;
+		}
+	}
+
+	dev_info(&pdev->dev, "%s: SmartReflex driver initialized\n", __func__);
+	if (!sr_dbg_dir) {
+		sr_dbg_dir = debugfs_create_dir("smartreflex", NULL);
+		if (IS_ERR_OR_NULL(sr_dbg_dir)) {
+			ret = PTR_ERR(sr_dbg_dir);
+			pr_err("%s:sr debugfs dir creation failed(%d)\n",
+				__func__, ret);
+			goto err_iounmap;
+		}
+	}
+
+	sr_info->dbg_dir = debugfs_create_dir(sr_info->name, sr_dbg_dir);
+	if (IS_ERR_OR_NULL(sr_info->dbg_dir)) {
+		dev_err(&pdev->dev, "%s: Unable to create debugfs directory\n",
+			__func__);
+		ret = PTR_ERR(sr_info->dbg_dir);
+		goto err_free_name;
+	}
+
+	(void) debugfs_create_file("autocomp", S_IRUGO | S_IWUSR,
+			sr_info->dbg_dir, (void *)sr_info, &pm_sr_fops);
+	(void) debugfs_create_x32("errweight", S_IRUGO, sr_info->dbg_dir,
+			&sr_info->err_weight);
+	(void) debugfs_create_x32("errmaxlimit", S_IRUGO, sr_info->dbg_dir,
+			&sr_info->err_maxlimit);
+
+	nvalue_dir = debugfs_create_dir("nvalue", sr_info->dbg_dir);
+	if (IS_ERR_OR_NULL(nvalue_dir)) {
+		dev_err(&pdev->dev, "%s: Unable to create debugfs directory"
+			"for n-values\n", __func__);
+		ret = PTR_ERR(nvalue_dir);
+		goto err_debugfs;
+	}
+
+	if (sr_info->nvalue_count == 0 || !sr_info->nvalue_table) {
+		dev_warn(&pdev->dev, "%s: %s: No Voltage table for the corresponding vdd. Cannot create debugfs entries for n-values\n",
+			 __func__, sr_info->name);
+
+		ret = -ENODATA;
+		goto err_debugfs;
+	}
+
+	for (i = 0; i < sr_info->nvalue_count; i++) {
+		char name[NVALUE_NAME_LEN + 1];
+
+		snprintf(name, sizeof(name), "volt_%lu",
+				sr_info->nvalue_table[i].volt_nominal);
+		(void) debugfs_create_x32(name, S_IRUGO | S_IWUSR, nvalue_dir,
+				&(sr_info->nvalue_table[i].nvalue));
+		snprintf(name, sizeof(name), "errminlimit_%lu",
+			 sr_info->nvalue_table[i].volt_nominal);
+		(void) debugfs_create_x32(name, S_IRUGO | S_IWUSR, nvalue_dir,
+				&(sr_info->nvalue_table[i].errminlimit));
+
+	}
+
+	return ret;
+
+err_debugfs:
+	debugfs_remove_recursive(sr_info->dbg_dir);
+err_free_name:
+	kfree(sr_info->name);
+err_iounmap:
+	list_del(&sr_info->node);
+	iounmap(sr_info->base);
+err_release_region:
+	release_mem_region(mem->start, resource_size(mem));
+err_free_devinfo:
+	kfree(sr_info);
+
+	return ret;
+}
+
+static int __devexit omap_sr_remove(struct platform_device *pdev)
+{
+	struct omap_sr_data *pdata = pdev->dev.platform_data;
+	struct omap_sr *sr_info;
+	struct resource *mem;
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
+		return -EINVAL;
+	}
+
+	sr_info = _sr_lookup(pdata->voltdm);
+	if (IS_ERR(sr_info)) {
+		dev_warn(&pdev->dev, "%s: omap_sr struct not found\n",
+			__func__);
+		return PTR_ERR(sr_info);
+	}
+
+	if (sr_info->autocomp_active)
+		sr_stop_vddautocomp(sr_info);
+	if (sr_info->dbg_dir)
+		debugfs_remove_recursive(sr_info->dbg_dir);
+
+	list_del(&sr_info->node);
+	iounmap(sr_info->base);
+	kfree(sr_info->name);
+	kfree(sr_info);
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	release_mem_region(mem->start, resource_size(mem));
+
+	return 0;
+}
+
+static void __devexit omap_sr_shutdown(struct platform_device *pdev)
+{
+	struct omap_sr_data *pdata = pdev->dev.platform_data;
+	struct omap_sr *sr_info;
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
+		return;
+	}
+
+	sr_info = _sr_lookup(pdata->voltdm);
+	if (IS_ERR(sr_info)) {
+		dev_warn(&pdev->dev, "%s: omap_sr struct not found\n",
+			__func__);
+		return;
+	}
+
+	if (sr_info->autocomp_active)
+		sr_stop_vddautocomp(sr_info);
+
+	return;
+}
+
+static struct platform_driver smartreflex_driver = {
+	.remove         = __devexit_p(omap_sr_remove),
+	.shutdown	= __devexit_p(omap_sr_shutdown),
+	.driver		= {
+		.name	= "smartreflex",
+	},
+};
+
+static int __init sr_init(void)
+{
+	int ret = 0;
+
+	/*
+	 * sr_init is a late init. If by then a pmic specific API is not
+	 * registered either there is no need for anything to be done on
+	 * the PMIC side or somebody has forgotten to register a PMIC
+	 * handler. Warn for the second condition.
+	 */
+	if (sr_pmic_data && sr_pmic_data->sr_pmic_init)
+		sr_pmic_data->sr_pmic_init();
+	else
+		pr_warning("%s: No PMIC hook to init smartreflex\n", __func__);
+
+	ret = platform_driver_probe(&smartreflex_driver, omap_sr_probe);
+	if (ret) {
+		pr_err("%s: platform driver register failed for SR\n",
+			__func__);
+		return ret;
+	}
+
+	return 0;
+}
+late_initcall(sr_init);
+
+static void __exit sr_exit(void)
+{
+	platform_driver_unregister(&smartreflex_driver);
+}
+module_exit(sr_exit);
+
+MODULE_DESCRIPTION("OMAP Smartreflex Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_AUTHOR("Texas Instruments Inc");