Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (110 commits)
  [SCSI] qla2xxx: Refactor call to qla2xxx_read_sfp for thermal temperature.
  [SCSI] qla2xxx: Unify the read/write sfp mailbox command routines.
  [SCSI] qla2xxx: Clear complete initialization control block.
  [SCSI] qla2xxx: Allow an override of the registered maximum LUN.
  [SCSI] qla2xxx: Add host number in reset and quiescent message logs.
  [SCSI] qla2xxx: Correctly read sfp single byte mailbox register.
  [SCSI] qla2xxx: Add qla82xx_rom_unlock() function.
  [SCSI] qla2xxx: Log if qla82xx firmware fails to load from flash.
  [SCSI] qla2xxx: Use passed in host to initialize local scsi_qla_host in queuecommand function
  [SCSI] qla2xxx: Correct buffer start in edc sysfs debug print.
  [SCSI] qla2xxx: Update firmware version after flash update for ISP82xx.
  [SCSI] qla2xxx: Fix hang during driver unload when vport is active.
  [SCSI] qla2xxx: Properly set the dsd_list_len for dsd_chaining in cmd type 6.
  [SCSI] qla2xxx: Fix virtual port failing to login after chip reset.
  [SCSI] qla2xxx: Fix vport delete hang when logins are outstanding.
  [SCSI] hpsa: Change memset using sizeof(ptr) to sizeof(*ptr)
  [SCSI] ipr: Rate limit DMA mapping errors
  [SCSI] hpsa: add P2000 to list of shared SAS devices
  [SCSI] hpsa: do not attempt PCI power management reset method if we know it won't work.
  [SCSI] hpsa: remove superfluous sleeps around reset code
  ...

1 files changed, 11 insertions, 4 deletions

diff --git a/drivers/scsi/hpsa.h b/drivers/scsi/hpsa.h
index 621a1530054a..6d8dcd4dd06b 100644
--- a/drivers/scsi/hpsa.h
+++ b/drivers/scsi/hpsa.h
@@ -127,10 +127,12 @@ struct ctlr_info {
 };
 #define HPSA_ABORT_MSG 0
 #define HPSA_DEVICE_RESET_MSG 1
-#define HPSA_BUS_RESET_MSG 2
-#define HPSA_HOST_RESET_MSG 3
+#define HPSA_RESET_TYPE_CONTROLLER 0x00
+#define HPSA_RESET_TYPE_BUS 0x01
+#define HPSA_RESET_TYPE_TARGET 0x03
+#define HPSA_RESET_TYPE_LUN 0x04
 #define HPSA_MSG_SEND_RETRY_LIMIT 10
-#define HPSA_MSG_SEND_RETRY_INTERVAL_MSECS 1000
+#define HPSA_MSG_SEND_RETRY_INTERVAL_MSECS (10000)
 
 /* Maximum time in seconds driver will wait for command completions
  * when polling before giving up.
@@ -155,7 +157,7 @@ struct ctlr_info {
  * HPSA_BOARD_READY_ITERATIONS are derived from those.
  */
 #define HPSA_BOARD_READY_WAIT_SECS (120)
-#define HPSA_BOARD_NOT_READY_WAIT_SECS (10)
+#define HPSA_BOARD_NOT_READY_WAIT_SECS (100)
 #define HPSA_BOARD_READY_POLL_INTERVAL_MSECS (100)
 #define HPSA_BOARD_READY_POLL_INTERVAL \
 	((HPSA_BOARD_READY_POLL_INTERVAL_MSECS * HZ) / 1000)
@@ -212,6 +214,7 @@ static void SA5_submit_command(struct ctlr_info *h,
 	dev_dbg(&h->pdev->dev, "Sending %x, tag = %x\n", c->busaddr,
 		c->Header.Tag.lower);
 	writel(c->busaddr, h->vaddr + SA5_REQUEST_PORT_OFFSET);
+	(void) readl(h->vaddr + SA5_REQUEST_PORT_OFFSET);
 	h->commands_outstanding++;
 	if (h->commands_outstanding > h->max_outstanding)
 		h->max_outstanding = h->commands_outstanding;
@@ -227,10 +230,12 @@ static void SA5_intr_mask(struct ctlr_info *h, unsigned long val)
 	if (val) { /* Turn interrupts on */
 		h->interrupts_enabled = 1;
 		writel(0, h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
+		(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
 	} else { /* Turn them off */
 		h->interrupts_enabled = 0;
 		writel(SA5_INTR_OFF,
 			h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
+		(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
 	}
 }
 
@@ -239,10 +244,12 @@ static void SA5_performant_intr_mask(struct ctlr_info *h, unsigned long val)
 	if (val) { /* turn on interrupts */
 		h->interrupts_enabled = 1;
 		writel(0, h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
+		(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
 	} else {
 		h->interrupts_enabled = 0;
 		writel(SA5_PERF_INTR_OFF,
 			h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
+		(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
 	}
 }