Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 711 insertions, 0 deletions

diff --git a/drivers/serial/serial_lh7a40x.c b/drivers/serial/serial_lh7a40x.c
new file mode 100644
index 000000000000..4ce3a41f1611
--- /dev/null
+++ b/drivers/serial/serial_lh7a40x.c
@@ -0,0 +1,711 @@
+/* drivers/serial/serial_lh7a40x.c
+ *
+ *  Copyright (C) 2004 Coastal Environmental Systems
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License
+ *  version 2 as published by the Free Software Foundation.
+ *
+ */
+
+/* Driver for Sharp LH7A40X embedded serial ports
+ *
+ *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ *  Based on drivers/serial/amba.c, by Deep Blue Solutions Ltd.
+ *
+ *  ---
+ *
+ * This driver supports the embedded UARTs of the Sharp LH7A40X series
+ * CPUs.  While similar to the 16550 and other UART chips, there is
+ * nothing close to register compatibility.  Moreover, some of the
+ * modem control lines are not available, either in the chip or they
+ * are lacking in the board-level implementation.
+ *
+ * - Use of SIRDIS
+ *   For simplicity, we disable the IR functions of any UART whenever
+ *   we enable it.
+ *
+ */
+
+#include <linux/config.h>
+
+#if defined(CONFIG_SERIAL_LH7A40X_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#define DEV_MAJOR	204
+#define DEV_MINOR	16
+#define DEV_NR		3
+
+#define ISR_LOOP_LIMIT	256
+
+#define UR(p,o)	_UR ((p)->membase, o)
+#define _UR(b,o) (*((volatile unsigned int*)(((unsigned char*) b) + (o))))
+#define BIT_CLR(p,o,m)	UR(p,o) = UR(p,o) & (~(unsigned int)m)
+#define BIT_SET(p,o,m)	UR(p,o) = UR(p,o) | ( (unsigned int)m)
+
+#define UART_REG_SIZE	32
+
+#define UART_R_DATA	(0x00)
+#define UART_R_FCON	(0x04)
+#define UART_R_BRCON	(0x08)
+#define UART_R_CON	(0x0c)
+#define UART_R_STATUS	(0x10)
+#define UART_R_RAWISR	(0x14)
+#define UART_R_INTEN	(0x18)
+#define UART_R_ISR	(0x1c)
+
+#define UARTEN		(0x01)		/* UART enable */
+#define SIRDIS		(0x02)		/* Serial IR disable (UART1 only) */
+
+#define RxEmpty		(0x10)
+#define TxEmpty		(0x80)
+#define TxFull		(0x20)
+#define nRxRdy		RxEmpty
+#define nTxRdy		TxFull
+#define TxBusy		(0x08)
+
+#define RxBreak		(0x0800)
+#define RxOverrunError	(0x0400)
+#define RxParityError	(0x0200)
+#define RxFramingError	(0x0100)
+#define RxError     (RxBreak | RxOverrunError | RxParityError | RxFramingError)
+
+#define DCD		(0x04)
+#define DSR		(0x02)
+#define CTS		(0x01)
+
+#define RxInt		(0x01)
+#define TxInt		(0x02)
+#define ModemInt	(0x04)
+#define RxTimeoutInt	(0x08)
+
+#define MSEOI		(0x10)
+
+#define WLEN_8		(0x60)
+#define WLEN_7		(0x40)
+#define WLEN_6		(0x20)
+#define WLEN_5		(0x00)
+#define WLEN		(0x60)	/* Mask for all word-length bits */
+#define STP2		(0x08)
+#define PEN		(0x02)	/* Parity Enable */
+#define EPS		(0x04)	/* Even Parity Set */
+#define FEN		(0x10)	/* FIFO Enable */
+#define BRK		(0x01)	/* Send Break */
+
+
+struct uart_port_lh7a40x {
+	struct uart_port port;
+	unsigned int statusPrev; /* Most recently read modem status */
+};
+
+static void lh7a40xuart_stop_tx (struct uart_port* port, unsigned int tty_stop)
+{
+	BIT_CLR (port, UART_R_INTEN, TxInt);
+}
+
+static void lh7a40xuart_start_tx (struct uart_port* port,
+				  unsigned int tty_start)
+{
+	BIT_SET (port, UART_R_INTEN, TxInt);
+
+	/* *** FIXME: do I need to check for startup of the
+		      transmitter?  The old driver did, but AMBA
+		      doesn't . */
+}
+
+static void lh7a40xuart_stop_rx (struct uart_port* port)
+{
+	BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt);
+}
+
+static void lh7a40xuart_enable_ms (struct uart_port* port)
+{
+	BIT_SET (port, UART_R_INTEN, ModemInt);
+}
+
+static void
+#ifdef SUPPORT_SYSRQ
+lh7a40xuart_rx_chars (struct uart_port* port, struct pt_regs* regs)
+#else
+lh7a40xuart_rx_chars (struct uart_port* port)
+#endif
+{
+	struct tty_struct* tty = port->info->tty;
+	int cbRxMax = 256;	/* (Gross) limit on receive */
+	unsigned int data, flag;/* Received data and status */
+
+	while (!(UR (port, UART_R_STATUS) & nRxRdy) && --cbRxMax) {
+		if (tty->flip.count >= TTY_FLIPBUF_SIZE) {
+			if (tty->low_latency)
+				tty_flip_buffer_push(tty);
+			/*
+			 * If this failed then we will throw away the
+			 * bytes but must do so to clear interrupts
+			 */
+		}
+
+		data = UR (port, UART_R_DATA);
+		flag = TTY_NORMAL;
+		++port->icount.rx;
+
+		if (data & RxError) {	/* Quick check, short-circuit */
+			if (data & RxBreak) {
+				data &= ~(RxFramingError | RxParityError);
+				++port->icount.brk;
+				if (uart_handle_break (port))
+					continue;
+			}
+			else if (data & RxParityError)
+				++port->icount.parity;
+			else if (data & RxFramingError)
+				++port->icount.frame;
+			if (data & RxOverrunError)
+				++port->icount.overrun;
+
+				/* Mask by termios, leave Rx'd byte */
+			data &= port->read_status_mask | 0xff;
+
+			if (data & RxBreak)
+				flag = TTY_BREAK;
+			else if (data & RxParityError)
+				flag = TTY_PARITY;
+			else if (data & RxFramingError)
+				flag = TTY_FRAME;
+		}
+
+		if (uart_handle_sysrq_char (port, (unsigned char) data, regs))
+			continue;
+
+		if ((data & port->ignore_status_mask) == 0) {
+			tty_insert_flip_char(tty, data, flag);
+		}
+		if ((data & RxOverrunError)
+		    && tty->flip.count < TTY_FLIPBUF_SIZE) {
+			/*
+			 * Overrun is special, since it's reported
+			 * immediately, and doesn't affect the current
+			 * character
+			 */
+			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+		}
+	}
+	tty_flip_buffer_push (tty);
+	return;
+}
+
+static void lh7a40xuart_tx_chars (struct uart_port* port)
+{
+	struct circ_buf* xmit = &port->info->xmit;
+	int cbTxMax = port->fifosize;
+
+	if (port->x_char) {
+		UR (port, UART_R_DATA) = port->x_char;
+		++port->icount.tx;
+		port->x_char = 0;
+		return;
+	}
+	if (uart_circ_empty (xmit) || uart_tx_stopped (port)) {
+		lh7a40xuart_stop_tx (port, 0);
+		return;
+	}
+
+	/* Unlike the AMBA UART, the lh7a40x UART does not guarantee
+	   that at least half of the FIFO is empty.  Instead, we check
+	   status for every character.  Using the AMBA method causes
+	   the transmitter to drop characters. */
+
+	do {
+		UR (port, UART_R_DATA) = xmit->buf[xmit->tail];
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		++port->icount.tx;
+		if (uart_circ_empty(xmit))
+			break;
+	} while (!(UR (port, UART_R_STATUS) & nTxRdy)
+		 && cbTxMax--);
+
+	if (uart_circ_chars_pending (xmit) < WAKEUP_CHARS)
+		uart_write_wakeup (port);
+
+	if (uart_circ_empty (xmit))
+		lh7a40xuart_stop_tx (port, 0);
+}
+
+static void lh7a40xuart_modem_status (struct uart_port* port)
+{
+	unsigned int status = UR (port, UART_R_STATUS);
+	unsigned int delta
+		= status ^ ((struct uart_port_lh7a40x*) port)->statusPrev;
+
+	BIT_SET (port, UART_R_RAWISR, MSEOI); /* Clear modem status intr */
+
+	if (!delta)		/* Only happens if we missed 2 transitions */
+		return;
+
+	((struct uart_port_lh7a40x*) port)->statusPrev = status;
+
+	if (delta & DCD)
+		uart_handle_dcd_change (port, status & DCD);
+
+	if (delta & DSR)
+		++port->icount.dsr;
+
+	if (delta & CTS)
+		uart_handle_cts_change (port, status & CTS);
+
+	wake_up_interruptible (&port->info->delta_msr_wait);
+}
+
+static irqreturn_t lh7a40xuart_int (int irq, void* dev_id,
+				    struct pt_regs* regs)
+{
+	struct uart_port* port = dev_id;
+	unsigned int cLoopLimit = ISR_LOOP_LIMIT;
+	unsigned int isr = UR (port, UART_R_ISR);
+
+
+	do {
+		if (isr & (RxInt | RxTimeoutInt))
+#ifdef SUPPORT_SYSRQ
+			lh7a40xuart_rx_chars(port, regs);
+#else
+			lh7a40xuart_rx_chars(port);
+#endif
+		if (isr & ModemInt)
+			lh7a40xuart_modem_status (port);
+		if (isr & TxInt)
+			lh7a40xuart_tx_chars (port);
+
+		if (--cLoopLimit == 0)
+			break;
+
+		isr = UR (port, UART_R_ISR);
+	} while (isr & (RxInt | TxInt | RxTimeoutInt));
+
+	return IRQ_HANDLED;
+}
+
+static unsigned int lh7a40xuart_tx_empty (struct uart_port* port)
+{
+	return (UR (port, UART_R_STATUS) & TxEmpty) ? TIOCSER_TEMT : 0;
+}
+
+static unsigned int lh7a40xuart_get_mctrl (struct uart_port* port)
+{
+	unsigned int result = 0;
+	unsigned int status = UR (port, UART_R_STATUS);
+
+	if (status & DCD)
+		result |= TIOCM_CAR;
+	if (status & DSR)
+		result |= TIOCM_DSR;
+	if (status & CTS)
+		result |= TIOCM_CTS;
+
+	return result;
+}
+
+static void lh7a40xuart_set_mctrl (struct uart_port* port, unsigned int mctrl)
+{
+	/* None of the ports supports DTR. UART1 supports RTS through GPIO. */
+	/* Note, kernel appears to be setting DTR and RTS on console. */
+
+	/* *** FIXME: this deserves more work.  There's some work in
+               tracing all of the IO pins. */
+#if 0
+	if( port->mapbase == UART1_PHYS) {
+		gpioRegs_t *gpio = (gpioRegs_t *)IO_ADDRESS(GPIO_PHYS);
+
+		if (mctrl & TIOCM_RTS)
+			gpio->pbdr &= ~GPIOB_UART1_RTS;
+		else
+			gpio->pbdr |= GPIOB_UART1_RTS;
+	}
+#endif
+}
+
+static void lh7a40xuart_break_ctl (struct uart_port* port, int break_state)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->lock, flags);
+	if (break_state == -1)
+		BIT_SET (port, UART_R_FCON, BRK); /* Assert break */
+	else
+		BIT_CLR (port, UART_R_FCON, BRK); /* Deassert break */
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static int lh7a40xuart_startup (struct uart_port* port)
+{
+	int retval;
+
+	retval = request_irq (port->irq, lh7a40xuart_int, 0,
+			      "serial_lh7a40x", port);
+	if (retval)
+		return retval;
+
+				/* Initial modem control-line settings */
+	((struct uart_port_lh7a40x*) port)->statusPrev
+		= UR (port, UART_R_STATUS);
+
+	/* There is presently no configuration option to enable IR.
+	   Thus, we always disable it. */
+
+	BIT_SET (port, UART_R_CON, UARTEN | SIRDIS);
+	BIT_SET (port, UART_R_INTEN, RxTimeoutInt | RxInt);
+
+	return 0;
+}
+
+static void lh7a40xuart_shutdown (struct uart_port* port)
+{
+	free_irq (port->irq, port);
+	BIT_CLR (port, UART_R_FCON, BRK | FEN);
+	BIT_CLR (port, UART_R_CON, UARTEN);
+}
+
+static void lh7a40xuart_set_termios (struct uart_port* port,
+				     struct termios* termios,
+				     struct termios* old)
+{
+	unsigned int con;
+	unsigned int inten;
+	unsigned int fcon;
+	unsigned long flags;
+	unsigned int baud;
+	unsigned int quot;
+
+	baud = uart_get_baud_rate (port, termios, old, 8, port->uartclk/16);
+	quot = uart_get_divisor (port, baud); /* -1 performed elsewhere */
+
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		fcon = WLEN_5;
+		break;
+	case CS6:
+		fcon = WLEN_6;
+		break;
+	case CS7:
+		fcon = WLEN_7;
+		break;
+	case CS8:
+	default:
+		fcon = WLEN_8;
+		break;
+	}
+	if (termios->c_cflag & CSTOPB)
+		fcon |= STP2;
+	if (termios->c_cflag & PARENB) {
+		fcon |= PEN;
+		if (!(termios->c_cflag & PARODD))
+			fcon |= EPS;
+	}
+	if (port->fifosize > 1)
+		fcon |= FEN;
+
+	spin_lock_irqsave (&port->lock, flags);
+
+	uart_update_timeout (port, termios->c_cflag, baud);
+
+	port->read_status_mask = RxOverrunError;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= RxFramingError | RxParityError;
+	if (termios->c_iflag & (BRKINT | PARMRK))
+		port->read_status_mask |= RxBreak;
+
+		/* Figure mask for status we ignore */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->ignore_status_mask |= RxFramingError | RxParityError;
+	if (termios->c_iflag & IGNBRK) {
+		port->ignore_status_mask |= RxBreak;
+		/* Ignore overrun when ignorning parity */
+		/* *** FIXME: is this in the right place? */
+		if (termios->c_iflag & IGNPAR)
+			port->ignore_status_mask |= RxOverrunError;
+	}
+
+		/* Ignore all receive errors when receive disabled */
+	if ((termios->c_cflag & CREAD) == 0)
+		port->ignore_status_mask |= RxError;
+
+	con   = UR (port, UART_R_CON);
+	inten = (UR (port, UART_R_INTEN) & ~ModemInt);
+
+	if (UART_ENABLE_MS (port, termios->c_cflag))
+		inten |= ModemInt;
+
+	BIT_CLR (port, UART_R_CON, UARTEN);	/* Disable UART */
+	UR (port, UART_R_INTEN) = 0;		/* Disable interrupts */
+	UR (port, UART_R_BRCON) = quot - 1;	/* Set baud rate divisor */
+	UR (port, UART_R_FCON)  = fcon;		/* Set FIFO and frame ctrl */
+	UR (port, UART_R_INTEN) = inten;	/* Enable interrupts */
+	UR (port, UART_R_CON)   = con;		/* Restore UART mode */
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char* lh7a40xuart_type (struct uart_port* port)
+{
+	return port->type == PORT_LH7A40X ? "LH7A40X" : NULL;
+}
+
+static void lh7a40xuart_release_port (struct uart_port* port)
+{
+	release_mem_region (port->mapbase, UART_REG_SIZE);
+}
+
+static int lh7a40xuart_request_port (struct uart_port* port)
+{
+	return request_mem_region (port->mapbase, UART_REG_SIZE,
+				   "serial_lh7a40x") != NULL
+		? 0 : -EBUSY;
+}
+
+static void lh7a40xuart_config_port (struct uart_port* port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE) {
+		port->type = PORT_LH7A40X;
+		lh7a40xuart_request_port (port);
+	}
+}
+
+static int lh7a40xuart_verify_port (struct uart_port* port,
+				    struct serial_struct* ser)
+{
+	int ret = 0;
+
+	if (ser->type != PORT_UNKNOWN && ser->type != PORT_LH7A40X)
+		ret = -EINVAL;
+	if (ser->irq < 0 || ser->irq >= NR_IRQS)
+		ret = -EINVAL;
+	if (ser->baud_base < 9600) /* *** FIXME: is this true? */
+		ret = -EINVAL;
+	return ret;
+}
+
+static struct uart_ops lh7a40x_uart_ops = {
+	.tx_empty	= lh7a40xuart_tx_empty,
+	.set_mctrl	= lh7a40xuart_set_mctrl,
+	.get_mctrl	= lh7a40xuart_get_mctrl,
+	.stop_tx	= lh7a40xuart_stop_tx,
+	.start_tx	= lh7a40xuart_start_tx,
+	.stop_rx	= lh7a40xuart_stop_rx,
+	.enable_ms	= lh7a40xuart_enable_ms,
+	.break_ctl	= lh7a40xuart_break_ctl,
+	.startup	= lh7a40xuart_startup,
+	.shutdown	= lh7a40xuart_shutdown,
+	.set_termios	= lh7a40xuart_set_termios,
+	.type		= lh7a40xuart_type,
+	.release_port	= lh7a40xuart_release_port,
+	.request_port	= lh7a40xuart_request_port,
+	.config_port	= lh7a40xuart_config_port,
+	.verify_port	= lh7a40xuart_verify_port,
+};
+
+static struct uart_port_lh7a40x lh7a40x_ports[DEV_NR] = {
+	{
+		.port = {
+			.membase	= (void*) io_p2v (UART1_PHYS),
+			.mapbase	= UART1_PHYS,
+			.iotype		= SERIAL_IO_MEM,
+			.irq		= IRQ_UART1INTR,
+			.uartclk	= 14745600/2,
+			.fifosize	= 16,
+			.ops		= &lh7a40x_uart_ops,
+			.flags		= ASYNC_BOOT_AUTOCONF,
+			.line		= 0,
+		},
+	},
+	{
+		.port = {
+			.membase	= (void*) io_p2v (UART2_PHYS),
+			.mapbase	= UART2_PHYS,
+			.iotype		= SERIAL_IO_MEM,
+			.irq		= IRQ_UART2INTR,
+			.uartclk	= 14745600/2,
+			.fifosize	= 16,
+			.ops		= &lh7a40x_uart_ops,
+			.flags		= ASYNC_BOOT_AUTOCONF,
+			.line		= 1,
+		},
+	},
+	{
+		.port = {
+			.membase	= (void*) io_p2v (UART3_PHYS),
+			.mapbase	= UART3_PHYS,
+			.iotype		= SERIAL_IO_MEM,
+			.irq		= IRQ_UART3INTR,
+			.uartclk	= 14745600/2,
+			.fifosize	= 16,
+			.ops		= &lh7a40x_uart_ops,
+			.flags		= ASYNC_BOOT_AUTOCONF,
+			.line		= 2,
+		},
+	},
+};
+
+#ifndef CONFIG_SERIAL_LH7A40X_CONSOLE
+# define LH7A40X_CONSOLE NULL
+#else
+# define LH7A40X_CONSOLE &lh7a40x_console
+
+
+static void lh7a40xuart_console_write (struct console* co,
+				       const char* s,
+				       unsigned int count)
+{
+	struct uart_port* port = &lh7a40x_ports[co->index].port;
+	unsigned int con = UR (port, UART_R_CON);
+	unsigned int inten = UR (port, UART_R_INTEN);
+
+
+	UR (port, UART_R_INTEN) = 0;		/* Disable all interrupts */
+	BIT_SET (port, UART_R_CON, UARTEN | SIRDIS); /* Enable UART */
+
+	for (; count-- > 0; ++s) {
+		while (UR (port, UART_R_STATUS) & nTxRdy)
+			;
+		UR (port, UART_R_DATA) = *s;
+		if (*s == '\n') {
+			while ((UR (port, UART_R_STATUS) & TxBusy))
+				;
+			UR (port, UART_R_DATA) = '\r';
+		}
+	}
+
+				/* Wait until all characters are sent */
+	while (UR (port, UART_R_STATUS) & TxBusy)
+		;
+
+				/* Restore control and interrupt mask */
+	UR (port, UART_R_CON) = con;
+	UR (port, UART_R_INTEN) = inten;
+}
+
+static void __init lh7a40xuart_console_get_options (struct uart_port* port,
+						    int* baud,
+						    int* parity,
+						    int* bits)
+{
+	if (UR (port, UART_R_CON) & UARTEN) {
+		unsigned int fcon = UR (port, UART_R_FCON);
+		unsigned int quot = UR (port, UART_R_BRCON) + 1;
+
+		switch (fcon & (PEN | EPS)) {
+		default:        *parity = 'n'; break;
+		case PEN:       *parity = 'o'; break;
+		case PEN | EPS: *parity = 'e'; break;
+		}
+
+		switch (fcon & WLEN) {
+		default:
+		case WLEN_8: *bits = 8; break;
+		case WLEN_7: *bits = 7; break;
+		case WLEN_6: *bits = 6; break;
+		case WLEN_5: *bits = 5; break;
+		}
+
+		*baud = port->uartclk/(16*quot);
+	}
+}
+
+static int __init lh7a40xuart_console_setup (struct console* co, char* options)
+{
+	struct uart_port* port;
+	int baud = 38400;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index >= DEV_NR) /* Bounds check on device number */
+		co->index = 0;
+	port = &lh7a40x_ports[co->index].port;
+
+	if (options)
+		uart_parse_options (options, &baud, &parity, &bits, &flow);
+	else
+		lh7a40xuart_console_get_options (port, &baud, &parity, &bits);
+
+	return uart_set_options (port, co, baud, parity, bits, flow);
+}
+
+extern struct uart_driver lh7a40x_reg;
+static struct console lh7a40x_console = {
+	.name		= "ttyAM",
+	.write		= lh7a40xuart_console_write,
+	.device		= uart_console_device,
+	.setup		= lh7a40xuart_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &lh7a40x_reg,
+};
+
+static int __init lh7a40xuart_console_init(void)
+{
+	register_console (&lh7a40x_console);
+	return 0;
+}
+
+console_initcall (lh7a40xuart_console_init);
+
+#endif
+
+static struct uart_driver lh7a40x_reg = {
+	.owner			= THIS_MODULE,
+	.driver_name		= "ttyAM",
+	.dev_name		= "ttyAM",
+	.major			= DEV_MAJOR,
+	.minor			= DEV_MINOR,
+	.nr			= DEV_NR,
+	.cons			= LH7A40X_CONSOLE,
+};
+
+static int __init lh7a40xuart_init(void)
+{
+	int ret;
+
+	printk (KERN_INFO "serial: LH7A40X serial driver\n");
+
+	ret = uart_register_driver (&lh7a40x_reg);
+
+	if (ret == 0) {
+		int i;
+
+		for (i = 0; i < DEV_NR; i++)
+			uart_add_one_port (&lh7a40x_reg,
+					   &lh7a40x_ports[i].port);
+	}
+	return ret;
+}
+
+static void __exit lh7a40xuart_exit(void)
+{
+	int i;
+
+	for (i = 0; i < DEV_NR; i++)
+		uart_remove_one_port (&lh7a40x_reg, &lh7a40x_ports[i].port);
+
+	uart_unregister_driver (&lh7a40x_reg);
+}
+
+module_init (lh7a40xuart_init);
+module_exit (lh7a40xuart_exit);
+
+MODULE_AUTHOR ("Marc Singer");
+MODULE_DESCRIPTION ("Sharp LH7A40X serial port driver");
+MODULE_LICENSE ("GPL");