Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6

Conflicts:

	Documentation/kernel-parameters.txt
	arch/sh/include/asm/elf.h

28 files changed, 415 insertions, 2554 deletions

diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 9ccc563d8730..1528de23a650 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -44,6 +44,10 @@
 
 #include "8250.h"
 
+#ifdef CONFIG_SPARC
+#include "suncore.h"
+#endif
+
 /*
  * Configuration:
  *   share_irqs - whether we pass IRQF_SHARED to request_irq().  This option
@@ -53,6 +57,13 @@ static unsigned int share_irqs = SERIAL8250_SHARE_IRQS;
 
 static unsigned int nr_uarts = CONFIG_SERIAL_8250_RUNTIME_UARTS;
 
+static struct uart_driver serial8250_reg;
+
+static int serial_index(struct uart_port *port)
+{
+	return (serial8250_reg.minor - 64) + port->line;
+}
+
 /*
  * Debugging.
  */
@@ -536,7 +547,7 @@ static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
 /*
  * FIFO support.
  */
-static inline void serial8250_clear_fifos(struct uart_8250_port *p)
+static void serial8250_clear_fifos(struct uart_8250_port *p)
 {
 	if (p->capabilities & UART_CAP_FIFO) {
 		serial_outp(p, UART_FCR, UART_FCR_ENABLE_FIFO);
@@ -551,7 +562,7 @@ static inline void serial8250_clear_fifos(struct uart_8250_port *p)
  * capability" bit enabled.  Note that on XR16C850s, we need to
  * reset LCR to write to IER.
  */
-static inline void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
+static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
 {
 	if (p->capabilities & UART_CAP_SLEEP) {
 		if (p->capabilities & UART_CAP_EFR) {
@@ -993,7 +1004,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
 		return;
 
 	DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04x, 0x%p): ",
-			up->port.line, up->port.iobase, up->port.membase);
+		       serial_index(&up->port), up->port.iobase, up->port.membase);
 
 	/*
 	 * We really do need global IRQs disabled here - we're going to
@@ -1128,8 +1139,8 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
 	if (up->capabilities != uart_config[up->port.type].flags) {
 		printk(KERN_WARNING
 		       "ttyS%d: detected caps %08x should be %08x\n",
-			up->port.line, up->capabilities,
-			uart_config[up->port.type].flags);
+		       serial_index(&up->port), up->capabilities,
+		       uart_config[up->port.type].flags);
 	}
 
 	up->port.fifosize = uart_config[up->port.type].fifo_size;
@@ -1424,8 +1435,7 @@ static unsigned int check_modem_status(struct uart_8250_port *up)
 /*
  * This handles the interrupt from one port.
  */
-static inline void
-serial8250_handle_port(struct uart_8250_port *up)
+static void serial8250_handle_port(struct uart_8250_port *up)
 {
 	unsigned int status;
 	unsigned long flags;
@@ -1719,7 +1729,7 @@ static void serial8250_break_ctl(struct uart_port *port, int break_state)
 /*
  *	Wait for transmitter & holding register to empty
  */
-static inline void wait_for_xmitr(struct uart_8250_port *up, int bits)
+static void wait_for_xmitr(struct uart_8250_port *up, int bits)
 {
 	unsigned int status, tmout = 10000;
 
@@ -1854,7 +1864,8 @@ static int serial8250_startup(struct uart_port *port)
 	 */
 	if (!(up->port.flags & UPF_BUGGY_UART) &&
 	    (serial_inp(up, UART_LSR) == 0xff)) {
-		printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
+		printk(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
+		       serial_index(&up->port));
 		return -ENODEV;
 	}
 
@@ -1909,7 +1920,8 @@ static int serial8250_startup(struct uart_port *port)
 		 */
 		if (!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) {
 			up->bugs |= UART_BUG_THRE;
-			pr_debug("ttyS%d - using backup timer\n", port->line);
+			pr_debug("ttyS%d - using backup timer\n",
+				 serial_index(port));
 		}
 	}
 
@@ -1969,7 +1981,7 @@ static int serial8250_startup(struct uart_port *port)
 		if (!(up->bugs & UART_BUG_TXEN)) {
 			up->bugs |= UART_BUG_TXEN;
 			pr_debug("ttyS%d - enabling bad tx status workarounds\n",
-				 port->line);
+				 serial_index(port));
 		}
 	} else {
 		up->bugs &= ~UART_BUG_TXEN;
@@ -2211,9 +2223,9 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
 		serial_outp(up, UART_EFR, efr);
 	}
 
-#ifdef CONFIG_ARCH_OMAP15XX
+#ifdef CONFIG_ARCH_OMAP
 	/* Workaround to enable 115200 baud on OMAP1510 internal ports */
-	if (cpu_is_omap1510() && is_omap_port((unsigned int)up->port.membase)) {
+	if (cpu_is_omap1510() && is_omap_port(up)) {
 		if (baud == 115200) {
 			quot = 1;
 			serial_out(up, UART_OMAP_OSC_12M_SEL, 1);
@@ -2266,18 +2278,27 @@ serial8250_pm(struct uart_port *port, unsigned int state,
 		p->pm(port, state, oldstate);
 }
 
+static unsigned int serial8250_port_size(struct uart_8250_port *pt)
+{
+	if (pt->port.iotype == UPIO_AU)
+		return 0x100000;
+#ifdef CONFIG_ARCH_OMAP
+	if (is_omap_port(pt))
+		return 0x16 << pt->port.regshift;
+#endif
+	return 8 << pt->port.regshift;
+}
+
 /*
  * Resource handling.
  */
 static int serial8250_request_std_resource(struct uart_8250_port *up)
 {
-	unsigned int size = 8 << up->port.regshift;
+	unsigned int size = serial8250_port_size(up);
 	int ret = 0;
 
 	switch (up->port.iotype) {
 	case UPIO_AU:
-		size = 0x100000;
-		/* fall thru */
 	case UPIO_TSI:
 	case UPIO_MEM32:
 	case UPIO_MEM:
@@ -2311,12 +2332,10 @@ static int serial8250_request_std_resource(struct uart_8250_port *up)
 
 static void serial8250_release_std_resource(struct uart_8250_port *up)
 {
-	unsigned int size = 8 << up->port.regshift;
+	unsigned int size = serial8250_port_size(up);
 
 	switch (up->port.iotype) {
 	case UPIO_AU:
-		size = 0x100000;
-		/* fall thru */
 	case UPIO_TSI:
 	case UPIO_MEM32:
 	case UPIO_MEM:
@@ -2630,7 +2649,6 @@ static int serial8250_console_early_setup(void)
 	return serial8250_find_port_for_earlycon();
 }
 
-static struct uart_driver serial8250_reg;
 static struct console serial8250_console = {
 	.name		= "ttyS",
 	.write		= serial8250_console_write,
@@ -2677,7 +2695,6 @@ static struct uart_driver serial8250_reg = {
 	.dev_name		= "ttyS",
 	.major			= TTY_MAJOR,
 	.minor			= 64,
-	.nr			= UART_NR,
 	.cons			= SERIAL8250_CONSOLE,
 };
 
@@ -2962,7 +2979,12 @@ static int __init serial8250_init(void)
 	for (i = 0; i < NR_IRQS; i++)
 		spin_lock_init(&irq_lists[i].lock);
 
+#ifdef CONFIG_SPARC
+	ret = sunserial_register_minors(&serial8250_reg, UART_NR);
+#else
+	serial8250_reg.nr = UART_NR;
 	ret = uart_register_driver(&serial8250_reg);
+#endif
 	if (ret)
 		goto out;
 
@@ -2987,7 +3009,11 @@ static int __init serial8250_init(void)
  put_dev:
 	platform_device_put(serial8250_isa_devs);
  unreg_uart_drv:
+#ifdef CONFIG_SPARC
+	sunserial_unregister_minors(&serial8250_reg, UART_NR);
+#else
 	uart_unregister_driver(&serial8250_reg);
+#endif
  out:
 	return ret;
 }
@@ -3006,7 +3032,11 @@ static void __exit serial8250_exit(void)
 	platform_driver_unregister(&serial8250_isa_driver);
 	platform_device_unregister(isa_dev);
 
+#ifdef CONFIG_SPARC
+	sunserial_unregister_minors(&serial8250_reg, UART_NR);
+#else
 	uart_unregister_driver(&serial8250_reg);
+#endif
 }
 
 module_init(serial8250_init);
diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
index c2f23933155b..c014ffb110e9 100644
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -2041,9 +2041,9 @@ static int pciserial_resume_one(struct pci_dev *dev)
 		 * The device may have been disabled.  Re-enable it.
 		 */
 		err = pci_enable_device(dev);
+		/* FIXME: We cannot simply error out here */
 		if (err)
-			return err;
-
+			printk(KERN_ERR "pciserial: Unable to re-enable ports, trying to continue.\n");
 		pciserial_resume_ports(priv);
 	}
 	return 0;
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 77cb34270fc1..db783b77a881 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -9,7 +9,6 @@ menu "Serial drivers"
 # The new 8250/16550 serial drivers
 config SERIAL_8250
 	tristate "8250/16550 and compatible serial support"
-	depends on (BROKEN || !SPARC)
 	select SERIAL_CORE
 	---help---
 	  This selects whether you want to include the driver for the standard
@@ -994,24 +993,12 @@ config SERIAL_68328_RTS_CTS
 	bool "Support RTS/CTS on 68328 serial port"
 	depends on SERIAL_68328
 
-config SERIAL_COLDFIRE
-	bool "ColdFire serial support (DEPRECATED)"
-	depends on COLDFIRE
-	help
-	  This driver supports the built-in serial ports of the Motorola ColdFire
-	  family of CPUs.
-	  This driver is deprecated because it supports only the old interface
-	  for serial drivers and features like magic keys are not working.
-	  Please switch to the new style driver because this driver will be
-	  removed soon.
-
 config SERIAL_MCF
-	bool "Coldfire serial support (new style driver)"
+	bool "Coldfire serial support"
 	depends on COLDFIRE
 	select SERIAL_CORE
 	help
-	  This new serial driver supports the Freescale Coldfire serial ports
-	  using the new serial driver subsystem.
+	  This serial driver supports the Freescale Coldfire serial ports.
 
 config SERIAL_MCF_BAUDRATE
 	int "Default baudrate for Coldfire serial ports"
@@ -1136,42 +1123,6 @@ config SERIAL_CPM_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
-config SERIAL_CPM_SCC1
-	bool "Support for SCC1 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SCC1 as a serial port
-
-config SERIAL_CPM_SCC2
-	bool "Support for SCC2 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SCC2 as a serial port
-
-config SERIAL_CPM_SCC3
-	bool "Support for SCC3 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SCC3 as a serial port
-
-config SERIAL_CPM_SCC4
-	bool "Support for SCC4 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SCC4 as a serial port
-
-config SERIAL_CPM_SMC1
-	bool "Support for SMC1 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SMC1 as a serial port
-
-config SERIAL_CPM_SMC2
-	bool "Support for SMC2 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SMC2 as a serial port
-
 config SERIAL_SGI_L1_CONSOLE
 	bool "SGI Altix L1 serial console support"
 	depends on IA64_GENERIC || IA64_SGI_SN2
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 7e7383e890d8..0c17c8ddb19d 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -4,6 +4,16 @@
 
 obj-$(CONFIG_SERIAL_CORE) += serial_core.o
 obj-$(CONFIG_SERIAL_21285) += 21285.o
+
+# These Sparc drivers have to appear before others such as 8250
+# which share ttySx minor node space.  Otherwise console device
+# names change and other unplesantries.
+obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
+obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o
+obj-$(CONFIG_SERIAL_SUNZILOG) += sunzilog.o
+obj-$(CONFIG_SERIAL_SUNSU) += sunsu.o
+obj-$(CONFIG_SERIAL_SUNSAB) += sunsab.o
+
 obj-$(CONFIG_SERIAL_8250) += 8250.o
 obj-$(CONFIG_SERIAL_8250_PNP) += 8250_pnp.o
 obj-$(CONFIG_SERIAL_8250_GSC) += 8250_gsc.o
@@ -31,16 +41,10 @@ obj-$(CONFIG_SERIAL_S3C2400) += s3c2400.o
 obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
 obj-$(CONFIG_SERIAL_S3C2412) += s3c2412.o
 obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o
-obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
-obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o
-obj-$(CONFIG_SERIAL_SUNZILOG) += sunzilog.o
 obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o
-obj-$(CONFIG_SERIAL_SUNSU) += sunsu.o
-obj-$(CONFIG_SERIAL_SUNSAB) += sunsab.o
 obj-$(CONFIG_SERIAL_MUX) += mux.o
 obj-$(CONFIG_SERIAL_68328) += 68328serial.o
 obj-$(CONFIG_SERIAL_68360) += 68360serial.o
-obj-$(CONFIG_SERIAL_COLDFIRE) += mcfserial.o
 obj-$(CONFIG_SERIAL_MCF) += mcf.o
 obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
 obj-$(CONFIG_SERIAL_LH7A40X) += serial_lh7a40x.o
diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c
index 3a6da80b081c..61fb8b6d19af 100644
--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -131,7 +131,8 @@ struct atmel_uart_char {
 struct atmel_uart_port {
 	struct uart_port	uart;		/* uart */
 	struct clk		*clk;		/* uart clock */
-	unsigned short		suspended;	/* is port suspended? */
+	int			may_wakeup;	/* cached value of device_may_wakeup for times we need to disable it */
+	u32			backup_imr;	/* IMR saved during suspend */
 	int			break_active;	/* break being received */
 
 	short			use_dma_rx;	/* enable PDC receiver */
@@ -984,8 +985,15 @@ static void atmel_serial_pm(struct uart_port *port, unsigned int state,
 		 * This is called on uart_open() or a resume event.
 		 */
 		clk_enable(atmel_port->clk);
+
+		/* re-enable interrupts if we disabled some on suspend */
+		UART_PUT_IER(port, atmel_port->backup_imr);
 		break;
 	case 3:
+		/* Back up the interrupt mask and disable all interrupts */
+		atmel_port->backup_imr = UART_GET_IMR(port);
+		UART_PUT_IDR(port, -1);
+
 		/*
 		 * Disable the peripheral clock for this serial port.
 		 * This is called on uart_close() or a suspend event.
@@ -1475,13 +1483,12 @@ static int atmel_serial_suspend(struct platform_device *pdev,
 			cpu_relax();
 	}
 
-	if (device_may_wakeup(&pdev->dev)
-	    && !atmel_serial_clk_will_stop())
-		enable_irq_wake(port->irq);
-	else {
-		uart_suspend_port(&atmel_uart, port);
-		atmel_port->suspended = 1;
-	}
+	/* we can not wake up if we're running on slow clock */
+	atmel_port->may_wakeup = device_may_wakeup(&pdev->dev);
+	if (atmel_serial_clk_will_stop())
+		device_set_wakeup_enable(&pdev->dev, 0);
+
+	uart_suspend_port(&atmel_uart, port);
 
 	return 0;
 }
@@ -1491,11 +1498,8 @@ static int atmel_serial_resume(struct platform_device *pdev)
 	struct uart_port *port = platform_get_drvdata(pdev);
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
 
-	if (atmel_port->suspended) {
-		uart_resume_port(&atmel_uart, port);
-		atmel_port->suspended = 0;
-	} else
-		disable_irq_wake(port->irq);
+	uart_resume_port(&atmel_uart, port);
+	device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup);
 
 	return 0;
 }
@@ -1513,6 +1517,8 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev)
 	BUILD_BUG_ON(!is_power_of_2(ATMEL_SERIAL_RINGSIZE));
 
 	port = &atmel_ports[pdev->id];
+	port->backup_imr = 0;
+
 	atmel_init_port(port, pdev);
 
 	if (!atmel_use_dma_rx(&port->uart)) {
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 4a0d30bed9f1..569f0e2476c6 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -1,7 +1,7 @@
 /*
  * Blackfin On-Chip Serial Driver
  *
- * Copyright 2006-2007 Analog Devices Inc.
+ * Copyright 2006-2008 Analog Devices Inc.
  *
  * Enter bugs at http://blackfin.uclinux.org/
  *
@@ -42,6 +42,9 @@
 #define BFIN_SERIAL_MAJOR	204
 #define BFIN_SERIAL_MINOR	64
 
+static struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
+static int nr_active_ports = ARRAY_SIZE(bfin_serial_resource);
+
 /*
  * Setup for console. Argument comes from the menuconfig
  */
@@ -126,13 +129,13 @@ static int kgdb_entry_state;
 void kgdb_put_debug_char(int chr)
 {
 	struct bfin_serial_port *uart;
-	
+
 	if (CONFIG_KGDB_UART_PORT < 0
 		|| CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS)
 		uart = &bfin_serial_ports[0];
 	else
 		uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
-	
+
 	while (!(UART_GET_LSR(uart) & THRE)) {
 		SSYNC();
 	}
@@ -152,7 +155,7 @@ int kgdb_get_debug_char(void)
 		uart = &bfin_serial_ports[0];
 	else
 		uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
-	
+
 	while(!(UART_GET_LSR(uart) & DR)) {
 		SSYNC();
 	}
@@ -298,7 +301,11 @@ static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
 	bfin_serial_mctrl_check(uart);
 
 	if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
-		bfin_serial_stop_tx(&uart->port);
+#ifdef CONFIG_BF54x
+		/* Clear TFI bit */
+		UART_PUT_LSR(uart, TFI);
+#endif
+		UART_CLEAR_IER(uart, ETBEI);
 		return;
 	}
 
@@ -317,9 +324,6 @@ static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
 
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(&uart->port);
-
-	if (uart_circ_empty(xmit))
-		bfin_serial_stop_tx(&uart->port);
 }
 
 static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id)
@@ -645,6 +649,42 @@ static int bfin_serial_startup(struct uart_port *port)
 		free_irq(uart->port.irq, uart);
 		return -EBUSY;
 	}
+
+# ifdef CONFIG_BF54x
+	{
+		unsigned uart_dma_ch_rx, uart_dma_ch_tx;
+
+		switch (uart->port.irq) {
+		case IRQ_UART3_RX:
+			uart_dma_ch_rx = CH_UART3_RX;
+			uart_dma_ch_tx = CH_UART3_TX;
+			break;
+		case IRQ_UART2_RX:
+			uart_dma_ch_rx = CH_UART2_RX;
+			uart_dma_ch_tx = CH_UART2_TX;
+			break;
+		default:
+			uart_dma_ch_rx = uart_dma_ch_tx = 0;
+			break;
+		};
+
+		if (uart_dma_ch_rx &&
+			request_dma(uart_dma_ch_rx, "BFIN_UART_RX") < 0) {
+			printk(KERN_NOTICE"Fail to attach UART interrupt\n");
+			free_irq(uart->port.irq, uart);
+			free_irq(uart->port.irq + 1, uart);
+			return -EBUSY;
+		}
+		if (uart_dma_ch_tx &&
+			request_dma(uart_dma_ch_tx, "BFIN_UART_TX") < 0) {
+			printk(KERN_NOTICE "Fail to attach UART interrupt\n");
+			free_dma(uart_dma_ch_rx);
+			free_irq(uart->port.irq, uart);
+			free_irq(uart->port.irq + 1, uart);
+			return -EBUSY;
+		}
+	}
+# endif
 #endif
 	UART_SET_IER(uart, ERBFI);
 	return 0;
@@ -662,6 +702,20 @@ static void bfin_serial_shutdown(struct uart_port *port)
 	del_timer(&(uart->rx_dma_timer));
 	dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0);
 #else
+#ifdef CONFIG_BF54x
+	switch (uart->port.irq) {
+	case IRQ_UART3_RX:
+		free_dma(CH_UART3_RX);
+		free_dma(CH_UART3_TX);
+		break;
+	case IRQ_UART2_RX:
+		free_dma(CH_UART2_RX);
+		free_dma(CH_UART2_TX);
+		break;
+	default:
+		break;
+	};
+#endif
 #ifdef	CONFIG_KGDB_UART
 	if (uart->port.line != CONFIG_KGDB_UART_PORT)
 #endif
@@ -757,6 +811,9 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
 	val |= UCEN;
 	UART_PUT_GCTL(uart, val);
 
+	/* Port speed changed, update the per-port timeout. */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
 	spin_unlock_irqrestore(&uart->port.lock, flags);
 }
 
@@ -859,8 +916,9 @@ static void __init bfin_serial_init_ports(void)
 		return;
 	first = 0;
 
-	for (i = 0; i < nr_ports; i++) {
+	for (i = 0; i < nr_active_ports; i++) {
 		bfin_serial_ports[i].port.uartclk   = get_sclk();
+		bfin_serial_ports[i].port.fifosize  = BFIN_UART_TX_FIFO_SIZE;
 		bfin_serial_ports[i].port.ops       = &bfin_serial_pops;
 		bfin_serial_ports[i].port.line      = i;
 		bfin_serial_ports[i].port.iotype    = UPIO_MEM;
@@ -961,7 +1019,7 @@ bfin_serial_console_setup(struct console *co, char *options)
 	 * if so, search for the first available port that does have
 	 * console support.
 	 */
-	if (co->index == -1 || co->index >= nr_ports)
+	if (co->index == -1 || co->index >= nr_active_ports)
 		co->index = 0;
 	uart = &bfin_serial_ports[co->index];
 
@@ -1056,7 +1114,7 @@ static __init void early_serial_write(struct console *con, const char *s,
 	}
 }
 
-static struct __init console bfin_early_serial_console = {
+static struct __initdata console bfin_early_serial_console = {
 	.name = "early_BFuart",
 	.write = early_serial_write,
 	.device = uart_console_device,
@@ -1072,7 +1130,7 @@ struct console __init *bfin_earlyserial_init(unsigned int port,
 	struct bfin_serial_port *uart;
 	struct ktermios t;
 
-	if (port == -1 || port >= nr_ports)
+	if (port == -1 || port >= nr_active_ports)
 		port = 0;
 	bfin_serial_init_ports();
 	bfin_early_serial_console.index = port;
@@ -1100,20 +1158,26 @@ static struct uart_driver bfin_serial_reg = {
 
 static int bfin_serial_suspend(struct platform_device *dev, pm_message_t state)
 {
-	struct bfin_serial_port *uart = platform_get_drvdata(dev);
+	int i;
 
-	if (uart)
-		uart_suspend_port(&bfin_serial_reg, &uart->port);
+	for (i = 0; i < nr_active_ports; i++) {
+		if (bfin_serial_ports[i].port.dev != &dev->dev)
+			continue;
+		uart_suspend_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+	}
 
 	return 0;
 }
 
 static int bfin_serial_resume(struct platform_device *dev)
 {
-	struct bfin_serial_port *uart = platform_get_drvdata(dev);
+	int i;
 
-	if (uart)
-		uart_resume_port(&bfin_serial_reg, &uart->port);
+	for (i = 0; i < nr_active_ports; i++) {
+		if (bfin_serial_ports[i].port.dev != &dev->dev)
+			continue;
+		uart_resume_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+	}
 
 	return 0;
 }
@@ -1128,32 +1192,31 @@ static int bfin_serial_probe(struct platform_device *dev)
 			break;
 
 	if (i < dev->num_resources) {
-		for (i = 0; i < nr_ports; i++, res++) {
+		for (i = 0; i < nr_active_ports; i++, res++) {
 			if (bfin_serial_ports[i].port.mapbase != res->start)
 				continue;
 			bfin_serial_ports[i].port.dev = &dev->dev;
 			uart_add_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
-			platform_set_drvdata(dev, &bfin_serial_ports[i]);
 		}
 	}
 
 	return 0;
 }
 
-static int bfin_serial_remove(struct platform_device *pdev)
+static int bfin_serial_remove(struct platform_device *dev)
 {
-	struct bfin_serial_port *uart = platform_get_drvdata(pdev);
-
+	int i;
 
+	for (i = 0; i < nr_active_ports; i++) {
+		if (bfin_serial_ports[i].port.dev != &dev->dev)
+			continue;
+		uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+		bfin_serial_ports[i].port.dev = NULL;
 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
-	gpio_free(uart->cts_pin);
-	gpio_free(uart->rts_pin);
+		gpio_free(bfin_serial_ports[i].cts_pin);
+		gpio_free(bfin_serial_ports[i].rts_pin);
 #endif
-
-	platform_set_drvdata(pdev, NULL);
-
-	if (uart)
-		uart_remove_one_port(&bfin_serial_reg, &uart->port);
+	}
 
 	return 0;
 }
diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c
index 25efca5a7a1f..a6c4d744495e 100644
--- a/drivers/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/serial/cpm_uart/cpm_uart_core.c
@@ -1333,6 +1333,9 @@ static int __devinit cpm_uart_probe(struct of_device *ofdev,
 	if (ret)
 		return ret;
 
+	/* initialize the device pointer for the port */
+	pinfo->port.dev = &ofdev->dev;
+
 	return uart_add_one_port(&cpm_reg, &pinfo->port);
 }
 
diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm1.c b/drivers/serial/cpm_uart/cpm_uart_cpm1.c
index 0f0aff06c596..1b94c56ec239 100644
--- a/drivers/serial/cpm_uart/cpm_uart_cpm1.c
+++ b/drivers/serial/cpm_uart/cpm_uart_cpm1.c
@@ -100,7 +100,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con)
 		mem_addr = (u8 *) cpm_dpram_addr(cpm_dpalloc(memsz, 8));
 		dma_addr = (u32)cpm_dpram_phys(mem_addr);
 	} else
-		mem_addr = dma_alloc_coherent(NULL, memsz, &dma_addr,
+		mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
 					      GFP_KERNEL);
 
 	if (mem_addr == NULL) {
@@ -127,8 +127,8 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con)
 
 void cpm_uart_freebuf(struct uart_cpm_port *pinfo)
 {
-	dma_free_coherent(NULL, L1_CACHE_ALIGN(pinfo->rx_nrfifos *
-					       pinfo->rx_fifosize) +
+	dma_free_coherent(pinfo->port.dev, L1_CACHE_ALIGN(pinfo->rx_nrfifos *
+							  pinfo->rx_fifosize) +
 			  L1_CACHE_ALIGN(pinfo->tx_nrfifos *
 					 pinfo->tx_fifosize), pinfo->mem_addr,
 			  pinfo->dma_addr);
diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
index b8db4d3eed36..141c0a3333ad 100644
--- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c
+++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
@@ -136,7 +136,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con)
 		dma_addr = virt_to_bus(mem_addr);
 	}
 	else
-		mem_addr = dma_alloc_coherent(NULL, memsz, &dma_addr,
+		mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
 					      GFP_KERNEL);
 
 	if (mem_addr == NULL) {
@@ -163,8 +163,8 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con)
 
 void cpm_uart_freebuf(struct uart_cpm_port *pinfo)
 {
-	dma_free_coherent(NULL, L1_CACHE_ALIGN(pinfo->rx_nrfifos *
-					       pinfo->rx_fifosize) +
+	dma_free_coherent(pinfo->port.dev, L1_CACHE_ALIGN(pinfo->rx_nrfifos *
+							  pinfo->rx_fifosize) +
 			  L1_CACHE_ALIGN(pinfo->tx_nrfifos *
 					 pinfo->tx_fifosize), (void __force *)pinfo->mem_addr,
 			  pinfo->dma_addr);
diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c
index bf94a770bb44..211c21797ce0 100644
--- a/drivers/serial/crisv10.c
+++ b/drivers/serial/crisv10.c
@@ -457,7 +457,6 @@ static struct e100_serial rs_table[] = {
 #define NR_PORTS (sizeof(rs_table)/sizeof(struct e100_serial))
 
 static struct ktermios *serial_termios[NR_PORTS];
-static struct ktermios *serial_termios_locked[NR_PORTS];
 #ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
 static struct fast_timer fast_timers[NR_PORTS];
 #endif
@@ -4419,6 +4418,7 @@ rs_init(void)
 			rs485_pa_bit)) {
 		printk(KERN_CRIT "ETRAX100LX serial: Could not allocate "
 			"RS485 pin\n");
+		put_tty_driver(driver);
 		return -EBUSY;
 	}
 #endif
@@ -4427,6 +4427,7 @@ rs_init(void)
 			rs485_port_g_bit)) {
 		printk(KERN_CRIT "ETRAX100LX serial: Could not allocate "
 			"RS485 pin\n");
+		put_tty_driver(driver);
 		return -EBUSY;
 	}
 #endif
@@ -4446,8 +4447,6 @@ rs_init(void)
 	driver->init_termios.c_ispeed = 115200;
 	driver->init_termios.c_ospeed = 115200;
 	driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
-	driver->termios = serial_termios;
-	driver->termios_locked = serial_termios_locked;
 
 	tty_set_operations(driver, &rs_ops);
         serial_driver = driver;
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index 6a29f9330a73..3f90f1bbbbcd 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -127,8 +127,13 @@
 #define  UCR3_RXDSEN	 (1<<6)  /* Receive status interrupt enable */
 #define  UCR3_AIRINTEN   (1<<5)  /* Async IR wake interrupt enable */
 #define  UCR3_AWAKEN	 (1<<4)  /* Async wake interrupt enable */
-#define  UCR3_REF25 	 (1<<3)  /* Ref freq 25 MHz */
-#define  UCR3_REF30 	 (1<<2)  /* Ref Freq 30 MHz */
+#ifdef CONFIG_ARCH_IMX
+#define  UCR3_REF25 	 (1<<3)  /* Ref freq 25 MHz, only on mx1 */
+#define  UCR3_REF30 	 (1<<2)  /* Ref Freq 30 MHz, only on mx1 */
+#endif
+#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
+#define  UCR3_RXDMUXSEL	 (1<<2)  /* RXD Muxed Input Select, on mx2/mx3 */
+#endif
 #define  UCR3_INVT  	 (1<<1)  /* Inverted Infrared transmission */
 #define  UCR3_BPEN  	 (1<<0)  /* Preset registers enable */
 #define  UCR4_CTSTL_32   (32<<10) /* CTS trigger level (32 chars) */
@@ -445,7 +450,7 @@ static irqreturn_t imx_int(int irq, void *dev_id)
 			readl(sport->port.membase + UCR1) & UCR1_TXMPTYEN)
 		imx_txint(irq, dev_id);
 
-	if (sts & USR1_RTSS)
+	if (sts & USR1_RTSD)
 		imx_rtsint(irq, dev_id);
 
 	return IRQ_HANDLED;
@@ -598,6 +603,12 @@ static int imx_startup(struct uart_port *port)
 	temp |= (UCR2_RXEN | UCR2_TXEN);
 	writel(temp, sport->port.membase + UCR2);
 
+#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
+	temp = readl(sport->port.membase + UCR3);
+	temp |= UCR3_RXDMUXSEL;
+	writel(temp, sport->port.membase + UCR3);
+#endif
+
 	/*
 	 * Enable modem status interrupts
 	 */
@@ -1133,13 +1144,19 @@ static int serial_imx_probe(struct platform_device *pdev)
 	if(pdata && (pdata->flags & IMXUART_HAVE_RTSCTS))
 		sport->have_rtscts = 1;
 
-	if (pdata->init)
-		pdata->init(pdev);
+	if (pdata->init) {
+		ret = pdata->init(pdev);
+		if (ret)
+			goto clkput;
+	}
 
 	uart_add_one_port(&imx_reg, &sport->port);
 	platform_set_drvdata(pdev, &sport->port);
 
 	return 0;
+clkput:
+	clk_put(sport->clk);
+	clk_disable(sport->clk);
 unmap:
 	iounmap(sport->port.membase);
 free:
diff --git a/drivers/serial/mcfserial.c b/drivers/serial/mcfserial.c
deleted file mode 100644
index fbe3835f6b77..000000000000
--- a/drivers/serial/mcfserial.c
+++ /dev/null
@@ -1,1965 +0,0 @@
-#warning This driver is deprecated. Check Kconfig for details.
-/*
- * mcfserial.c -- serial driver for ColdFire internal UARTS.
- *
- * Copyright (C) 1999-2003 Greg Ungerer <gerg@snapgear.com>
- * Copyright (c) 2000-2001 Lineo, Inc. <www.lineo.com> 
- * Copyright (C) 2001-2002 SnapGear Inc. <www.snapgear.com> 
- *
- * Based on code from 68332serial.c which was:
- *
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
- * Copyright (C) 1998 TSHG
- * Copyright (c) 1999 Rt-Control Inc. <jeff@uclinux.org>
- *
- * Changes:
- * 08/07/2003    Daniele Bellucci <bellucda@tiscali.it>
- *               some cleanups in mcfrs_write.
- *
- */
- 
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/timer.h>
-#include <linux/wait.h>
-#include <linux/interrupt.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/string.h>
-#include <linux/fcntl.h>
-#include <linux/mm.h>
-#include <linux/kernel.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/console.h>
-#include <linux/init.h>
-#include <linux/bitops.h>
-#include <linux/delay.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-#include <asm/delay.h>
-#include <asm/coldfire.h>
-#include <asm/mcfsim.h>
-#include <asm/mcfuart.h>
-#include <asm/nettel.h>
-#include <asm/uaccess.h>
-#include "mcfserial.h"
-
-struct timer_list mcfrs_timer_struct;
-
-/*
- *	Default console baud rate,  we use this as the default
- *	for all ports so init can just open /dev/console and
- *	keep going.  Perhaps one day the cflag settings for the
- *	console can be used instead.
- */
-#if defined(CONFIG_HW_FEITH)
-#define	CONSOLE_BAUD_RATE	38400
-#define	DEFAULT_CBAUD		B38400
-#elif defined(CONFIG_MOD5272) || defined(CONFIG_M5208EVB) || \
-      defined(CONFIG_M5329EVB) || defined(CONFIG_GILBARCO)
-#define CONSOLE_BAUD_RATE 	115200
-#define DEFAULT_CBAUD		B115200
-#elif defined(CONFIG_ARNEWSH) || defined(CONFIG_FREESCALE) || \
-      defined(CONFIG_senTec) || defined(CONFIG_SNEHA) || defined(CONFIG_AVNET)
-#define	CONSOLE_BAUD_RATE	19200
-#define	DEFAULT_CBAUD		B19200
-#endif
-
-#ifndef CONSOLE_BAUD_RATE
-#define	CONSOLE_BAUD_RATE	9600
-#define	DEFAULT_CBAUD		B9600
-#endif
-
-int mcfrs_console_inited = 0;
-int mcfrs_console_port = -1;
-int mcfrs_console_baud = CONSOLE_BAUD_RATE;
-int mcfrs_console_cbaud = DEFAULT_CBAUD;
-
-/*
- *	Driver data structures.
- */
-static struct tty_driver *mcfrs_serial_driver;
-
-/* number of characters left in xmit buffer before we ask for more */
-#define WAKEUP_CHARS 256
-
-/* Debugging...
- */
-#undef SERIAL_DEBUG_OPEN
-#undef SERIAL_DEBUG_FLOW
-
-#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \
-    defined(CONFIG_M520x) || defined(CONFIG_M532x)
-#define	IRQBASE	(MCFINT_VECBASE+MCFINT_UART0)
-#else
-#define	IRQBASE	73
-#endif
-
-/*
- *	Configuration table, UARTs to look for at startup.
- */
-static struct mcf_serial mcfrs_table[] = {
-	{  /* ttyS0 */
-		.magic = 0,
-		.addr = (volatile unsigned char *) (MCF_MBAR+MCFUART_BASE1),
-		.irq = IRQBASE,
-		.flags = ASYNC_BOOT_AUTOCONF,
-	},
-#ifdef MCFUART_BASE2
-	{  /* ttyS1 */
-		.magic = 0,
-		.addr = (volatile unsigned char *) (MCF_MBAR+MCFUART_BASE2),
-		.irq = IRQBASE+1,
-		.flags = ASYNC_BOOT_AUTOCONF,
-	},
-#endif
-#ifdef MCFUART_BASE3
-	{  /* ttyS2 */
-		.magic = 0,
-		.addr = (volatile unsigned char *) (MCF_MBAR+MCFUART_BASE3),
-		.irq = IRQBASE+2,
-		.flags = ASYNC_BOOT_AUTOCONF,
-	},
-#endif
-#ifdef MCFUART_BASE4
-	{  /* ttyS3 */
-		.magic = 0,
-		.addr = (volatile unsigned char *) (MCF_MBAR+MCFUART_BASE4),
-		.irq = IRQBASE+3,
-		.flags = ASYNC_BOOT_AUTOCONF,
-	},
-#endif
-};
-
-
-#define	NR_PORTS	(sizeof(mcfrs_table) / sizeof(struct mcf_serial))
-
-/*
- * This is used to figure out the divisor speeds and the timeouts.
- */
-static int mcfrs_baud_table[] = {
-	0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
-	9600, 19200, 38400, 57600, 115200, 230400, 460800, 0
-};
-#define MCFRS_BAUD_TABLE_SIZE \
-			(sizeof(mcfrs_baud_table)/sizeof(mcfrs_baud_table[0]))
-
-
-#ifdef CONFIG_MAGIC_SYSRQ
-/*
- *	Magic system request keys. Used for debugging...
- */
-extern int	magic_sysrq_key(int ch);
-#endif
-
-
-/*
- *	Forware declarations...
- */
-static void	mcfrs_change_speed(struct mcf_serial *info);
-static void	mcfrs_wait_until_sent(struct tty_struct *tty, int timeout);
-
-
-static inline int serial_paranoia_check(struct mcf_serial *info,
-					char *name, const char *routine)
-{
-#ifdef SERIAL_PARANOIA_CHECK
-	static const char badmagic[] =
-		"MCFRS(warning): bad magic number for serial struct %s in %s\n";
-	static const char badinfo[] =
-		"MCFRS(warning): null mcf_serial for %s in %s\n";
-
-	if (!info) {
-		printk(badinfo, name, routine);
-		return 1;
-	}
-	if (info->magic != SERIAL_MAGIC) {
-		printk(badmagic, name, routine);
-		return 1;
-	}
-#endif
-	return 0;
-}
-
-/*
- *	Sets or clears DTR and RTS on the requested line.
- */
-static void mcfrs_setsignals(struct mcf_serial *info, int dtr, int rts)
-{
-	volatile unsigned char	*uartp;
-	unsigned long		flags;
-	
-#if 0
-	printk("%s(%d): mcfrs_setsignals(info=%x,dtr=%d,rts=%d)\n",
-		__FILE__, __LINE__, info, dtr, rts);
-#endif
-
-	local_irq_save(flags);
-	if (dtr >= 0) {
-#ifdef MCFPP_DTR0
-		if (info->line)
-			mcf_setppdata(MCFPP_DTR1, (dtr ? 0 : MCFPP_DTR1));
-		else
-			mcf_setppdata(MCFPP_DTR0, (dtr ? 0 : MCFPP_DTR0));
-#endif
-	}
-	if (rts >= 0) {
-		uartp = info->addr;
-		if (rts) {
-			info->sigs |= TIOCM_RTS;
-			uartp[MCFUART_UOP1] = MCFUART_UOP_RTS;
-		} else {
-			info->sigs &= ~TIOCM_RTS;
-			uartp[MCFUART_UOP0] = MCFUART_UOP_RTS;
-		}
-	}
-	local_irq_restore(flags);
-	return;
-}
-
-/*
- *	Gets values of serial signals.
- */
-static int mcfrs_getsignals(struct mcf_serial *info)
-{
-	volatile unsigned char	*uartp;
-	unsigned long		flags;
-	int			sigs;
-#if defined(CONFIG_NETtel) && defined(CONFIG_M5307)
-	unsigned short		ppdata;
-#endif
-
-#if 0
-	printk("%s(%d): mcfrs_getsignals(info=%x)\n", __FILE__, __LINE__);
-#endif
-
-	local_irq_save(flags);
-	uartp = info->addr;
-	sigs = (uartp[MCFUART_UIPR] & MCFUART_UIPR_CTS) ? 0 : TIOCM_CTS;
-	sigs |= (info->sigs & TIOCM_RTS);
-
-#ifdef MCFPP_DCD0
-{
-	unsigned int ppdata;
-	ppdata = mcf_getppdata();
-	if (info->line == 0) {
-		sigs |= (ppdata & MCFPP_DCD0) ? 0 : TIOCM_CD;
-		sigs |= (ppdata & MCFPP_DTR0) ? 0 : TIOCM_DTR;
-	} else if (info->line == 1) {
-		sigs |= (ppdata & MCFPP_DCD1) ? 0 : TIOCM_CD;
-		sigs |= (ppdata & MCFPP_DTR1) ? 0 : TIOCM_DTR;
-	}
-}
-#endif
-
-	local_irq_restore(flags);
-	return(sigs);
-}
-
-/*
- * ------------------------------------------------------------
- * mcfrs_stop() and mcfrs_start()
- *
- * This routines are called before setting or resetting tty->stopped.
- * They enable or disable transmitter interrupts, as necessary.
- * ------------------------------------------------------------
- */
-static void mcfrs_stop(struct tty_struct *tty)
-{
-	volatile unsigned char	*uartp;
-	struct mcf_serial	*info = (struct mcf_serial *)tty->driver_data;
-	unsigned long		flags;
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_stop"))
-		return;
-	
-	local_irq_save(flags);
-	uartp = info->addr;
-	info->imr &= ~MCFUART_UIR_TXREADY;
-	uartp[MCFUART_UIMR] = info->imr;
-	local_irq_restore(flags);
-}
-
-static void mcfrs_start(struct tty_struct *tty)
-{
-	volatile unsigned char	*uartp;
-	struct mcf_serial	*info = (struct mcf_serial *)tty->driver_data;
-	unsigned long		flags;
-	
-	if (serial_paranoia_check(info, tty->name, "mcfrs_start"))
-		return;
-
-	local_irq_save(flags);
-	if (info->xmit_cnt && info->xmit_buf) {
-		uartp = info->addr;
-		info->imr |= MCFUART_UIR_TXREADY;
-		uartp[MCFUART_UIMR] = info->imr;
-	}
-	local_irq_restore(flags);
-}
-
-/*
- * ----------------------------------------------------------------------
- *
- * Here starts the interrupt handling routines.  All of the following
- * subroutines are declared as inline and are folded into
- * mcfrs_interrupt().  They were separated out for readability's sake.
- *
- * Note: mcfrs_interrupt() is a "fast" interrupt, which means that it
- * runs with interrupts turned off.  People who may want to modify
- * mcfrs_interrupt() should try to keep the interrupt handler as fast as
- * possible.  After you are done making modifications, it is not a bad
- * idea to do:
- * 
- * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c
- *
- * and look at the resulting assemble code in serial.s.
- *
- * 				- Ted Ts'o (tytso@mit.edu), 7-Mar-93
- * -----------------------------------------------------------------------
- */
-
-static inline void receive_chars(struct mcf_serial *info)
-{
-	volatile unsigned char	*uartp;
-	struct tty_struct	*tty = info->port.tty;
-	unsigned char		status, ch, flag;
-
-	if (!tty)
-		return;
-
-	uartp = info->addr;
-
-	while ((status = uartp[MCFUART_USR]) & MCFUART_USR_RXREADY) {
-		ch = uartp[MCFUART_URB];
-		info->stats.rx++;
-
-#ifdef CONFIG_MAGIC_SYSRQ
-		if (mcfrs_console_inited && (info->line == mcfrs_console_port)) {
-			if (magic_sysrq_key(ch))
-				continue;
-		}
-#endif
-
-		flag = TTY_NORMAL;
-		if (status & MCFUART_USR_RXERR) {
-			uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETERR;
-			if (status & MCFUART_USR_RXBREAK) {
-				info->stats.rxbreak++;
-				flag = TTY_BREAK;
-			} else if (status & MCFUART_USR_RXPARITY) {
-				info->stats.rxparity++;
-				flag = TTY_PARITY;
-			} else if (status & MCFUART_USR_RXOVERRUN) {
-				info->stats.rxoverrun++;
-				flag = TTY_OVERRUN;
-			} else if (status & MCFUART_USR_RXFRAMING) {
-				info->stats.rxframing++;
-				flag = TTY_FRAME;
-			}
-		}
-		tty_insert_flip_char(tty, ch, flag);
-	}
-	tty_schedule_flip(tty);
-	return;
-}
-
-static inline void transmit_chars(struct mcf_serial *info)
-{
-	volatile unsigned char	*uartp;
-
-	uartp = info->addr;
-
-	if (info->x_char) {
-		/* Send special char - probably flow control */
-		uartp[MCFUART_UTB] = info->x_char;
-		info->x_char = 0;
-		info->stats.tx++;
-	}
-
-	if ((info->xmit_cnt <= 0) || info->port.tty->stopped) {
-		info->imr &= ~MCFUART_UIR_TXREADY;
-		uartp[MCFUART_UIMR] = info->imr;
-		return;
-	}
-
-	while (uartp[MCFUART_USR] & MCFUART_USR_TXREADY) {
-		uartp[MCFUART_UTB] = info->xmit_buf[info->xmit_tail++];
-		info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
-		info->stats.tx++;
-		if (--info->xmit_cnt <= 0)
-			break;
-	}
-
-	if (info->xmit_cnt < WAKEUP_CHARS)
-		schedule_work(&info->tqueue);
-	return;
-}
-
-/*
- * This is the serial driver's generic interrupt routine
- */
-irqreturn_t mcfrs_interrupt(int irq, void *dev_id)
-{
-	struct mcf_serial	*info;
-	unsigned char		isr;
-
-	info = &mcfrs_table[(irq - IRQBASE)];
-	isr = info->addr[MCFUART_UISR] & info->imr;
-
-	if (isr & MCFUART_UIR_RXREADY)
-		receive_chars(info);
-	if (isr & MCFUART_UIR_TXREADY)
-		transmit_chars(info);
-	return IRQ_HANDLED;
-}
-
-/*
- * -------------------------------------------------------------------
- * Here ends the serial interrupt routines.
- * -------------------------------------------------------------------
- */
-
-static void mcfrs_offintr(struct work_struct *work)
-{
-	struct mcf_serial *info = container_of(work, struct mcf_serial, tqueue);
-	struct tty_struct *tty = info->port.tty;
-	
-	if (tty)
-		tty_wakeup(tty);
-}
-
-
-/*
- *	Change of state on a DCD line.
- */
-void mcfrs_modem_change(struct mcf_serial *info, int dcd)
-{
-	if (info->count == 0)
-		return;
-
-	if (info->flags & ASYNC_CHECK_CD) {
-		if (dcd)
-			wake_up_interruptible(&info->open_wait);
-		else 
-			schedule_work(&info->tqueue_hangup);
-	}
-}
-
-
-#ifdef MCFPP_DCD0
-
-unsigned short	mcfrs_ppstatus;
-
-/*
- * This subroutine is called when the RS_TIMER goes off. It is used
- * to monitor the state of the DCD lines - since they have no edge
- * sensors and interrupt generators.
- */
-static void mcfrs_timer(void)
-{
-	unsigned int	ppstatus, dcdval, i;
-
-	ppstatus = mcf_getppdata() & (MCFPP_DCD0 | MCFPP_DCD1);
-
-	if (ppstatus != mcfrs_ppstatus) {
-		for (i = 0; (i < 2); i++) {
-			dcdval = (i ? MCFPP_DCD1 : MCFPP_DCD0);
-			if ((ppstatus & dcdval) != (mcfrs_ppstatus & dcdval)) {
-				mcfrs_modem_change(&mcfrs_table[i],
-					((ppstatus & dcdval) ? 0 : 1));
-			}
-		}
-	}
-	mcfrs_ppstatus = ppstatus;
-
-	/* Re-arm timer */
-	mcfrs_timer_struct.expires = jiffies + HZ/25;
-	add_timer(&mcfrs_timer_struct);
-}
-
-#endif	/* MCFPP_DCD0 */
-
-
-/*
- * This routine is called from the scheduler tqueue when the interrupt
- * routine has signalled that a hangup has occurred. The path of
- * hangup processing is:
- *
- * 	serial interrupt routine -> (scheduler tqueue) ->
- * 	do_serial_hangup() -> tty->hangup() -> mcfrs_hangup()
- * 
- */
-static void do_serial_hangup(struct work_struct *work)
-{
-	struct mcf_serial *info = container_of(work, struct mcf_serial, tqueue_hangup);
-	struct tty_struct *tty = info->port.tty;
-	
-	if (tty)
-		tty_hangup(tty);
-}
-
-static int startup(struct mcf_serial * info)
-{
-	volatile unsigned char	*uartp;
-	unsigned long		flags;
-	
-	if (info->flags & ASYNC_INITIALIZED)
-		return 0;
-
-	if (!info->xmit_buf) {
-		info->xmit_buf = (unsigned char *) __get_free_page(GFP_KERNEL);
-		if (!info->xmit_buf)
-			return -ENOMEM;
-	}
-
-	local_irq_save(flags);
-
-#ifdef SERIAL_DEBUG_OPEN
-	printk("starting up ttyS%d (irq %d)...\n", info->line, info->irq);
-#endif
-
-	/*
-	 *	Reset UART, get it into known state...
-	 */
-	uartp = info->addr;
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX;  /* reset RX */
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETTX;  /* reset TX */
-	mcfrs_setsignals(info, 1, 1);
-
-	if (info->port.tty)
-		clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
-	info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
-
-	/*
-	 * and set the speed of the serial port
-	 */
-	mcfrs_change_speed(info);
-
-	/*
-	 * Lastly enable the UART transmitter and receiver, and
-	 * interrupt enables.
-	 */
-	info->imr = MCFUART_UIR_RXREADY;
-	uartp[MCFUART_UCR] = MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE;
-	uartp[MCFUART_UIMR] = info->imr;
-
-	info->flags |= ASYNC_INITIALIZED;
-	local_irq_restore(flags);
-	return 0;
-}
-
-/*
- * This routine will shutdown a serial port; interrupts are disabled, and
- * DTR is dropped if the hangup on close termio flag is on.
- */
-static void shutdown(struct mcf_serial * info)
-{
-	volatile unsigned char	*uartp;
-	unsigned long		flags;
-
-	if (!(info->flags & ASYNC_INITIALIZED))
-		return;
-
-#ifdef SERIAL_DEBUG_OPEN
-	printk("Shutting down serial port %d (irq %d)....\n", info->line,
-	       info->irq);
-#endif
-	
-	local_irq_save(flags);
-
-	uartp = info->addr;
-	uartp[MCFUART_UIMR] = 0;  /* mask all interrupts */
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX;  /* reset RX */
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETTX;  /* reset TX */
-
-	if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL))
-		mcfrs_setsignals(info, 0, 0);
-
-	if (info->xmit_buf) {
-		free_page((unsigned long) info->xmit_buf);
-		info->xmit_buf = 0;
-	}
-
-	if (info->port.tty)
-		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
-	
-	info->flags &= ~ASYNC_INITIALIZED;
-	local_irq_restore(flags);
-}
-
-
-/*
- * This routine is called to set the UART divisor registers to match
- * the specified baud rate for a serial port.
- */
-static void mcfrs_change_speed(struct mcf_serial *info)
-{
-	volatile unsigned char	*uartp;
-	unsigned int		baudclk, cflag;
-	unsigned long		flags;
-	unsigned char		mr1, mr2;
-	int			i;
-#ifdef	CONFIG_M5272
-	unsigned int		fraction;
-#endif
-
-	if (!info->port.tty || !info->port.tty->termios)
-		return;
-	cflag = info->port.tty->termios->c_cflag;
-	if (info->addr == 0)
-		return;
-
-#if 0
-	printk("%s(%d): mcfrs_change_speed()\n", __FILE__, __LINE__);
-#endif
-
-	i = cflag & CBAUD;
-	if (i & CBAUDEX) {
-		i &= ~CBAUDEX;
-		if (i < 1 || i > 4)
-			info->port.tty->termios->c_cflag &= ~CBAUDEX;
-		else
-			i += 15;
-	}
-	if (i == 0) {
-		mcfrs_setsignals(info, 0, -1);
-		return;
-	}
-
-	/* compute the baudrate clock */
-#ifdef	CONFIG_M5272
-	/*
-	 * For the MCF5272, also compute the baudrate fraction.
-	 */
-	baudclk = (MCF_BUSCLK / mcfrs_baud_table[i]) / 32;
-	fraction = MCF_BUSCLK - (baudclk * 32 * mcfrs_baud_table[i]);
-	fraction *= 16;
-	fraction /= (32 * mcfrs_baud_table[i]);
-#else
-	baudclk = ((MCF_BUSCLK / mcfrs_baud_table[i]) + 16) / 32;
-#endif
-
-	info->baud = mcfrs_baud_table[i];
-
-	mr1 = MCFUART_MR1_RXIRQRDY | MCFUART_MR1_RXERRCHAR;
-	mr2 = 0;
-
-	switch (cflag & CSIZE) {
-	case CS5:	mr1 |= MCFUART_MR1_CS5; break;
-	case CS6:	mr1 |= MCFUART_MR1_CS6; break;
-	case CS7:	mr1 |= MCFUART_MR1_CS7; break;
-	case CS8:
-	default:	mr1 |= MCFUART_MR1_CS8; break;
-	}
-
-	if (cflag & PARENB) {
-		if (cflag & CMSPAR) {
-			if (cflag & PARODD)
-				mr1 |= MCFUART_MR1_PARITYMARK;
-			else
-				mr1 |= MCFUART_MR1_PARITYSPACE;
-		} else {
-			if (cflag & PARODD)
-				mr1 |= MCFUART_MR1_PARITYODD;
-			else
-				mr1 |= MCFUART_MR1_PARITYEVEN;
-		}
-	} else {
-		mr1 |= MCFUART_MR1_PARITYNONE;
-	}
-
-	if (cflag & CSTOPB)
-		mr2 |= MCFUART_MR2_STOP2;
-	else
-		mr2 |= MCFUART_MR2_STOP1;
-
-	if (cflag & CRTSCTS) {
-		mr1 |= MCFUART_MR1_RXRTS;
-		mr2 |= MCFUART_MR2_TXCTS;
-	}
-
-	if (cflag & CLOCAL)
-		info->flags &= ~ASYNC_CHECK_CD;
-	else
-		info->flags |= ASYNC_CHECK_CD;
-
-	uartp = info->addr;
-
-	local_irq_save(flags);
-#if 0
-	printk("%s(%d): mr1=%x mr2=%x baudclk=%x\n", __FILE__, __LINE__,
-		mr1, mr2, baudclk);
-#endif
-	/*
-	  Note: pg 12-16 of MCF5206e User's Manual states that a
-	  software reset should be performed prior to changing
-	  UMR1,2, UCSR, UACR, bit 7
-	*/
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX;    /* reset RX */
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETTX;    /* reset TX */
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETMRPTR;	/* reset MR pointer */
-	uartp[MCFUART_UMR] = mr1;
-	uartp[MCFUART_UMR] = mr2;
-	uartp[MCFUART_UBG1] = (baudclk & 0xff00) >> 8;	/* set msb byte */
-	uartp[MCFUART_UBG2] = (baudclk & 0xff);		/* set lsb byte */
-#ifdef	CONFIG_M5272
-	uartp[MCFUART_UFPD] = (fraction & 0xf);		/* set fraction */
-#endif
-	uartp[MCFUART_UCSR] = MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER;
-	uartp[MCFUART_UCR] = MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE;
-	mcfrs_setsignals(info, 1, -1);
-	local_irq_restore(flags);
-	return;
-}
-
-static void mcfrs_flush_chars(struct tty_struct *tty)
-{
-	volatile unsigned char	*uartp;
-	struct mcf_serial	*info = (struct mcf_serial *)tty->driver_data;
-	unsigned long		flags;
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_flush_chars"))
-		return;
-
-	uartp = (volatile unsigned char *) info->addr;
-
-	/*
-	 * re-enable receiver interrupt
-	 */
-	local_irq_save(flags);
-	if ((!(info->imr & MCFUART_UIR_RXREADY)) &&
-	    (info->flags & ASYNC_INITIALIZED) ) {
-		info->imr |= MCFUART_UIR_RXREADY;
-		uartp[MCFUART_UIMR] = info->imr;
-	}
-	local_irq_restore(flags);
-
-	if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
-	    !info->xmit_buf)
-		return;
-
-	/* Enable transmitter */
-	local_irq_save(flags);
-	info->imr |= MCFUART_UIR_TXREADY;
-	uartp[MCFUART_UIMR] = info->imr;
-	local_irq_restore(flags);
-}
-
-static int mcfrs_write(struct tty_struct * tty,
-		    const unsigned char *buf, int count)
-{
-	volatile unsigned char	*uartp;
-	struct mcf_serial	*info = (struct mcf_serial *)tty->driver_data;
-	unsigned long		flags;
-	int			c, total = 0;
-
-#if 0
-	printk("%s(%d): mcfrs_write(tty=%x,buf=%x,count=%d)\n",
-		__FILE__, __LINE__, (int)tty, (int)buf, count);
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_write"))
-		return 0;
-
-	if (!tty || !info->xmit_buf)
-		return 0;
-	
-	local_save_flags(flags);
-	while (1) {
-		local_irq_disable();		
-		c = min(count, (int) min(((int)SERIAL_XMIT_SIZE) - info->xmit_cnt - 1,
-			((int)SERIAL_XMIT_SIZE) - info->xmit_head));
-		local_irq_restore(flags);
-
-		if (c <= 0)
-			break;
-
-		memcpy(info->xmit_buf + info->xmit_head, buf, c);
-
-		local_irq_disable();
-		info->xmit_head = (info->xmit_head + c) & (SERIAL_XMIT_SIZE-1);
-		info->xmit_cnt += c;
-		local_irq_restore(flags);
-
-		buf += c;
-		count -= c;
-		total += c;
-	}
-
-	local_irq_disable();
-	uartp = info->addr;
-	info->imr |= MCFUART_UIR_TXREADY;
-	uartp[MCFUART_UIMR] = info->imr;
-	local_irq_restore(flags);
-
-	return total;
-}
-
-static int mcfrs_write_room(struct tty_struct *tty)
-{
-	struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
-	int	ret;
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_write_room"))
-		return 0;
-	ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
-	if (ret < 0)
-		ret = 0;
-	return ret;
-}
-
-static int mcfrs_chars_in_buffer(struct tty_struct *tty)
-{
-	struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_chars_in_buffer"))
-		return 0;
-	return info->xmit_cnt;
-}
-
-static void mcfrs_flush_buffer(struct tty_struct *tty)
-{
-	struct mcf_serial	*info = (struct mcf_serial *)tty->driver_data;
-	unsigned long		flags;
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_flush_buffer"))
-		return;
-
-	local_irq_save(flags);
-	info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
-	local_irq_restore(flags);
-
-	tty_wakeup(tty);
-}
-
-/*
- * ------------------------------------------------------------
- * mcfrs_throttle()
- * 
- * This routine is called by the upper-layer tty layer to signal that
- * incoming characters should be throttled.
- * ------------------------------------------------------------
- */
-static void mcfrs_throttle(struct tty_struct * tty)
-{
-	struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
-#ifdef SERIAL_DEBUG_THROTTLE
-	char	buf[64];
-	
-	printk("throttle %s: %d....\n", tty_name(tty, buf),
-	       tty->ldisc.chars_in_buffer(tty));
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_throttle"))
-		return;
-	
-	if (I_IXOFF(tty))
-		info->x_char = STOP_CHAR(tty);
-
-	/* Turn off RTS line (do this atomic) */
-}
-
-static void mcfrs_unthrottle(struct tty_struct * tty)
-{
-	struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
-#ifdef SERIAL_DEBUG_THROTTLE
-	char	buf[64];
-	
-	printk("unthrottle %s: %d....\n", tty_name(tty, buf),
-	       tty->ldisc.chars_in_buffer(tty));
-#endif
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_unthrottle"))
-		return;
-	
-	if (I_IXOFF(tty)) {
-		if (info->x_char)
-			info->x_char = 0;
-		else
-			info->x_char = START_CHAR(tty);
-	}
-
-	/* Assert RTS line (do this atomic) */
-}
-
-/*
- * ------------------------------------------------------------
- * mcfrs_ioctl() and friends
- * ------------------------------------------------------------
- */
-
-static int get_serial_info(struct mcf_serial * info,
-			   struct serial_struct * retinfo)
-{
-	struct serial_struct tmp;
-  
-	if (!retinfo)
-		return -EFAULT;
-	memset(&tmp, 0, sizeof(tmp));
-	tmp.type = info->type;
-	tmp.line = info->line;
-	tmp.port = (unsigned int) info->addr;
-	tmp.irq = info->irq;
-	tmp.flags = info->flags;
-	tmp.baud_base = info->baud_base;
-	tmp.close_delay = info->close_delay;
-	tmp.closing_wait = info->closing_wait;
-	tmp.custom_divisor = info->custom_divisor;
-	return copy_to_user(retinfo,&tmp,sizeof(*retinfo)) ? -EFAULT : 0;
-}
-
-static int set_serial_info(struct mcf_serial * info,
-			   struct serial_struct * new_info)
-{
-	struct serial_struct new_serial;
-	struct mcf_serial old_info;
-	int 	retval = 0;
-
-	if (!new_info)
-		return -EFAULT;
-	if (copy_from_user(&new_serial,new_info,sizeof(new_serial)))
-		return -EFAULT;
-	old_info = *info;
-
-	if (!capable(CAP_SYS_ADMIN)) {
-		if ((new_serial.baud_base != info->baud_base) ||
-		    (new_serial.type != info->type) ||
-		    (new_serial.close_delay != info->close_delay) ||
-		    ((new_serial.flags & ~ASYNC_USR_MASK) !=
-		     (info->flags & ~ASYNC_USR_MASK)))
-			return -EPERM;
-		info->flags = ((info->flags & ~ASYNC_USR_MASK) |
-			       (new_serial.flags & ASYNC_USR_MASK));
-		info->custom_divisor = new_serial.custom_divisor;
-		goto check_and_exit;
-	}
-
-	if (info->count > 1)
-		return -EBUSY;
-
-	/*
-	 * OK, past this point, all the error checking has been done.
-	 * At this point, we start making changes.....
-	 */
-
-	info->baud_base = new_serial.baud_base;
-	info->flags = ((info->flags & ~ASYNC_FLAGS) |
-			(new_serial.flags & ASYNC_FLAGS));
-	info->type = new_serial.type;
-	info->close_delay = new_serial.close_delay;
-	info->closing_wait = new_serial.closing_wait;
-
-check_and_exit:
-	retval = startup(info);
-	return retval;
-}
-
-/*
- * get_lsr_info - get line status register info
- *
- * Purpose: Let user call ioctl() to get info when the UART physically
- * 	    is emptied.  On bus types like RS485, the transmitter must
- * 	    release the bus after transmitting. This must be done when
- * 	    the transmit shift register is empty, not be done when the
- * 	    transmit holding register is empty.  This functionality
- * 	    allows an RS485 driver to be written in user space. 
- */
-static int get_lsr_info(struct mcf_serial * info, unsigned int *value)
-{
-	volatile unsigned char	*uartp;
-	unsigned long		flags;
-	unsigned char		status;
-
-	local_irq_save(flags);
-	uartp = info->addr;
-	status = (uartp[MCFUART_USR] & MCFUART_USR_TXEMPTY) ? TIOCSER_TEMT : 0;
-	local_irq_restore(flags);
-
-	return put_user(status,value);
-}
-
-/*
- * This routine sends a break character out the serial port.
- */
-static void send_break(	struct mcf_serial * info, int duration)
-{
-	volatile unsigned char	*uartp;
-	unsigned long		flags;
-
-	if (!info->addr)
-		return;
-	set_current_state(TASK_INTERRUPTIBLE);
-	uartp = info->addr;
-
-	local_irq_save(flags);
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDBREAKSTART;
-	schedule_timeout(duration);
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDBREAKSTOP;
-	local_irq_restore(flags);
-}
-
-static int mcfrs_tiocmget(struct tty_struct *tty, struct file *file)
-{
-	struct mcf_serial * info = (struct mcf_serial *)tty->driver_data;
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_ioctl"))
-		return -ENODEV;
-	if (tty->flags & (1 << TTY_IO_ERROR))
-		return -EIO;
-
-	return mcfrs_getsignals(info);
-}
-
-static int mcfrs_tiocmset(struct tty_struct *tty, struct file *file,
-			  unsigned int set, unsigned int clear)
-{
-	struct mcf_serial * info = (struct mcf_serial *)tty->driver_data;
-	int rts = -1, dtr = -1;
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_ioctl"))
-		return -ENODEV;
-	if (tty->flags & (1 << TTY_IO_ERROR))
-		return -EIO;
-
-	if (set & TIOCM_RTS)
-		rts = 1;
-	if (set & TIOCM_DTR)
-		dtr = 1;
-	if (clear & TIOCM_RTS)
-		rts = 0;
-	if (clear & TIOCM_DTR)
-		dtr = 0;
-
-	mcfrs_setsignals(info, dtr, rts);
-
-	return 0;
-}
-
-static int mcfrs_ioctl(struct tty_struct *tty, struct file * file,
-		    unsigned int cmd, unsigned long arg)
-{
-	struct mcf_serial * info = (struct mcf_serial *)tty->driver_data;
-	int retval, error;
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_ioctl"))
-		return -ENODEV;
-
-	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
-	    (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD)  &&
-	    (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
-		    return -EIO;
-	}
-	
-	switch (cmd) {
-		case TCSBRK:	/* SVID version: non-zero arg --> no break */
-			retval = tty_check_change(tty);
-			if (retval)
-				return retval;
-			tty_wait_until_sent(tty, 0);
-			if (!arg)
-				send_break(info, HZ/4);	/* 1/4 second */
-			return 0;
-		case TCSBRKP:	/* support for POSIX tcsendbreak() */
-			retval = tty_check_change(tty);
-			if (retval)
-				return retval;
-			tty_wait_until_sent(tty, 0);
-			send_break(info, arg ? arg*(HZ/10) : HZ/4);
-			return 0;
-		case TIOCGSERIAL:
-			if (access_ok(VERIFY_WRITE, (void *) arg,
-						sizeof(struct serial_struct)))
-				return get_serial_info(info,
-					       (struct serial_struct *) arg);
-			return -EFAULT;
-		case TIOCSSERIAL:
-			return set_serial_info(info,
-					       (struct serial_struct *) arg);
-		case TIOCSERGETLSR: /* Get line status register */
-			if (access_ok(VERIFY_WRITE, (void *) arg,
-						sizeof(unsigned int)))
-				return get_lsr_info(info, (unsigned int *) arg);
-			return -EFAULT;
-		case TIOCSERGSTRUCT:
-			error = copy_to_user((struct mcf_serial *) arg,
-				    info, sizeof(struct mcf_serial));
-			if (error)
-				return -EFAULT;
-			return 0;
-			
-#ifdef TIOCSET422
-		case TIOCSET422: {
-			unsigned int val;
-			get_user(val, (unsigned int *) arg);
-			mcf_setpa(MCFPP_PA11, (val ? 0 : MCFPP_PA11));
-			break;
-		}
-		case TIOCGET422: {
-			unsigned int val;
-			val = (mcf_getpa() & MCFPP_PA11) ? 0 : 1;
-			put_user(val, (unsigned int *) arg);
-			break;
-		}
-#endif
-
-		default:
-			return -ENOIOCTLCMD;
-		}
-	return 0;
-}
-
-static void mcfrs_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
-{
-	struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
-
-	if (tty->termios->c_cflag == old_termios->c_cflag)
-		return;
-
-	mcfrs_change_speed(info);
-
-	if ((old_termios->c_cflag & CRTSCTS) &&
-	    !(tty->termios->c_cflag & CRTSCTS)) {
-		tty->hw_stopped = 0;
-		mcfrs_setsignals(info, -1, 1);
-#if 0
-		mcfrs_start(tty);
-#endif
-	}
-}
-
-/*
- * ------------------------------------------------------------
- * mcfrs_close()
- * 
- * This routine is called when the serial port gets closed.  First, we
- * wait for the last remaining data to be sent.  Then, we unlink its
- * S structure from the interrupt chain if necessary, and we free
- * that IRQ if nothing is left in the chain.
- * ------------------------------------------------------------
- */
-static void mcfrs_close(struct tty_struct *tty, struct file * filp)
-{
-	volatile unsigned char	*uartp;
-	struct mcf_serial	*info = (struct mcf_serial *)tty->driver_data;
-	unsigned long		flags;
-
-	if (!info || serial_paranoia_check(info, tty->name, "mcfrs_close"))
-		return;
-	
-	local_irq_save(flags);
-	
-	if (tty_hung_up_p(filp)) {
-		local_irq_restore(flags);
-		return;
-	}
-	
-#ifdef SERIAL_DEBUG_OPEN
-	printk("mcfrs_close ttyS%d, count = %d\n", info->line, info->count);
-#endif
-	if ((tty->count == 1) && (info->count != 1)) {
-		/*
-		 * Uh, oh.  tty->count is 1, which means that the tty
-		 * structure will be freed.  Info->count should always
-		 * be one in these conditions.  If it's greater than
-		 * one, we've got real problems, since it means the
-		 * serial port won't be shutdown.
-		 */
-		printk("MCFRS: bad serial port count; tty->count is 1, "
-		       "info->count is %d\n", info->count);
-		info->count = 1;
-	}
-	if (--info->count < 0) {
-		printk("MCFRS: bad serial port count for ttyS%d: %d\n",
-		       info->line, info->count);
-		info->count = 0;
-	}
-	if (info->count) {
-		local_irq_restore(flags);
-		return;
-	}
-	info->flags |= ASYNC_CLOSING;
-
-	/*
-	 * Now we wait for the transmit buffer to clear; and we notify 
-	 * the line discipline to only process XON/XOFF characters.
-	 */
-	tty->closing = 1;
-	if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE)
-		tty_wait_until_sent(tty, info->closing_wait);
-
-	/*
-	 * At this point we stop accepting input.  To do this, we
-	 * disable the receive line status interrupts, and tell the
-	 * interrupt driver to stop checking the data ready bit in the
-	 * line status register.
-	 */
-	info->imr &= ~MCFUART_UIR_RXREADY;
-	uartp = info->addr;
-	uartp[MCFUART_UIMR] = info->imr;
-
-#if 0
-	/* FIXME: do we need to keep this enabled for console?? */
-	if (mcfrs_console_inited && (mcfrs_console_port == info->line)) {
-		/* Do not disable the UART */ ;
-	} else
-#endif
-	shutdown(info);
-	mcfrs_flush_buffer(tty);
-	tty_ldisc_flush(tty);
-	
-	tty->closing = 0;
-	info->event = 0;
-	info->port.tty = NULL;
-#if 0	
-	if (tty->ldisc.num != ldiscs[N_TTY].num) {
-		if (tty->ldisc.close)
-			(tty->ldisc.close)(tty);
-		tty->ldisc = ldiscs[N_TTY];
-		tty->termios->c_line = N_TTY;
-		if (tty->ldisc.open)
-			(tty->ldisc.open)(tty);
-	}
-#endif	
-	if (info->blocked_open) {
-		if (info->close_delay) {
-			msleep_interruptible(jiffies_to_msecs(info->close_delay));
-		}
-		wake_up_interruptible(&info->open_wait);
-	}
-	info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
-	wake_up_interruptible(&info->close_wait);
-	local_irq_restore(flags);
-}
-
-/*
- * mcfrs_wait_until_sent() --- wait until the transmitter is empty
- */
-static void
-mcfrs_wait_until_sent(struct tty_struct *tty, int timeout)
-{
-#ifdef	CONFIG_M5272
-#define	MCF5272_FIFO_SIZE	25		/* fifo size + shift reg */
-
-	struct mcf_serial * info = (struct mcf_serial *)tty->driver_data;
-	volatile unsigned char *uartp;
-	unsigned long orig_jiffies, fifo_time, char_time, fifo_cnt;
-
-	if (serial_paranoia_check(info, tty->name, "mcfrs_wait_until_sent"))
-		return;
-
-	orig_jiffies = jiffies;
-
-	/*
-	 * Set the check interval to be 1/5 of the approximate time
-	 * to send the entire fifo, and make it at least 1.  The check
-	 * interval should also be less than the timeout.
-	 *
-	 * Note: we have to use pretty tight timings here to satisfy
-	 * the NIST-PCTS.
-	 */
-	lock_kernel();
-
-	fifo_time = (MCF5272_FIFO_SIZE * HZ * 10) / info->baud;
-	char_time = fifo_time / 5;
-	if (char_time == 0)
-		char_time = 1;
-	if (timeout && timeout < char_time)
-		char_time = timeout;
-
-	/*
-	 * Clamp the timeout period at 2 * the time to empty the
-	 * fifo.  Just to be safe, set the minimum at .5 seconds.
-	 */
-	fifo_time *= 2;
-	if (fifo_time < (HZ/2))
-		fifo_time = HZ/2;
-	if (!timeout || timeout > fifo_time)
-		timeout = fifo_time;
-
-	/*
-	 * Account for the number of bytes in the UART
-	 * transmitter FIFO plus any byte being shifted out.
-	 */
-	uartp = (volatile unsigned char *) info->addr;
-	for (;;) {
-		fifo_cnt = (uartp[MCFUART_UTF] & MCFUART_UTF_TXB);
-		if ((uartp[MCFUART_USR] & (MCFUART_USR_TXREADY|
-				MCFUART_USR_TXEMPTY)) ==
-			MCFUART_USR_TXREADY)
-			fifo_cnt++;
-		if (fifo_cnt == 0)
-			break;
-		msleep_interruptible(jiffies_to_msecs(char_time));
-		if (signal_pending(current))
-			break;
-		if (timeout && time_after(jiffies, orig_jiffies + timeout))
-			break;
-	}
-	unlock_kernel();
-#else
-	/*
-	 * For the other coldfire models, assume all data has been sent
-	 */
-#endif
-}
-
-/*
- * mcfrs_hangup() --- called by tty_hangup() when a hangup is signaled.
- */
-void mcfrs_hangup(struct tty_struct *tty)
-{
-	struct mcf_serial * info = (struct mcf_serial *)tty->driver_data;
-	
-	if (serial_paranoia_check(info, tty->name, "mcfrs_hangup"))
-		return;
-	
-	mcfrs_flush_buffer(tty);
-	shutdown(info);
-	info->event = 0;
-	info->count = 0;
-	info->flags &= ~ASYNC_NORMAL_ACTIVE;
-	info->port.tty = NULL;
-	wake_up_interruptible(&info->open_wait);
-}
-
-/*
- * ------------------------------------------------------------
- * mcfrs_open() and friends
- * ------------------------------------------------------------
- */
-static int block_til_ready(struct tty_struct *tty, struct file * filp,
-			   struct mcf_serial *info)
-{
-	DECLARE_WAITQUEUE(wait, current);
-	int	retval;
-	int	do_clocal = 0;
-
-	/*
-	 * If the device is in the middle of being closed, then block
-	 * until it's done, and then try again.
-	 */
-	if (info->flags & ASYNC_CLOSING) {
-		interruptible_sleep_on(&info->close_wait);
-#ifdef SERIAL_DO_RESTART
-		if (info->flags & ASYNC_HUP_NOTIFY)
-			return -EAGAIN;
-		else
-			return -ERESTARTSYS;
-#else
-		return -EAGAIN;
-#endif
-	}
-	
-	/*
-	 * If non-blocking mode is set, or the port is not enabled,
-	 * then make the check up front and then exit.
-	 */
-	if ((filp->f_flags & O_NONBLOCK) ||
-	    (tty->flags & (1 << TTY_IO_ERROR))) {
-		info->flags |= ASYNC_NORMAL_ACTIVE;
-		return 0;
-	}
-
-	if (tty->termios->c_cflag & CLOCAL)
-		do_clocal = 1;
-
-	/*
-	 * Block waiting for the carrier detect and the line to become
-	 * free (i.e., not in use by the callout).  While we are in
-	 * this loop, info->count is dropped by one, so that
-	 * mcfrs_close() knows when to free things.  We restore it upon
-	 * exit, either normal or abnormal.
-	 */
-	retval = 0;
-	add_wait_queue(&info->open_wait, &wait);
-#ifdef SERIAL_DEBUG_OPEN
-	printk("block_til_ready before block: ttyS%d, count = %d\n",
-	       info->line, info->count);
-#endif
-	info->count--;
-	info->blocked_open++;
-	while (1) {
-		local_irq_disable();
-		mcfrs_setsignals(info, 1, 1);
-		local_irq_enable();
-		current->state = TASK_INTERRUPTIBLE;
-		if (tty_hung_up_p(filp) ||
-		    !(info->flags & ASYNC_INITIALIZED)) {
-#ifdef SERIAL_DO_RESTART
-			if (info->flags & ASYNC_HUP_NOTIFY)
-				retval = -EAGAIN;
-			else
-				retval = -ERESTARTSYS;	
-#else
-			retval = -EAGAIN;
-#endif
-			break;
-		}
-		if (!(info->flags & ASYNC_CLOSING) &&
-		    (do_clocal || (mcfrs_getsignals(info) & TIOCM_CD)))
-			break;
-		if (signal_pending(current)) {
-			retval = -ERESTARTSYS;
-			break;
-		}
-#ifdef SERIAL_DEBUG_OPEN
-		printk("block_til_ready blocking: ttyS%d, count = %d\n",
-		       info->line, info->count);
-#endif
-		schedule();
-	}
-	current->state = TASK_RUNNING;
-	remove_wait_queue(&info->open_wait, &wait);
-	if (!tty_hung_up_p(filp))
-		info->count++;
-	info->blocked_open--;
-#ifdef SERIAL_DEBUG_OPEN
-	printk("block_til_ready after blocking: ttyS%d, count = %d\n",
-	       info->line, info->count);
-#endif
-	if (retval)
-		return retval;
-	info->flags |= ASYNC_NORMAL_ACTIVE;
-	return 0;
-}	
-
-/*
- * This routine is called whenever a serial port is opened. It
- * enables interrupts for a serial port, linking in its structure into
- * the IRQ chain.   It also performs the serial-specific
- * initialization for the tty structure.
- */
-int mcfrs_open(struct tty_struct *tty, struct file * filp)
-{
-	struct mcf_serial	*info;
-	int 			retval, line;
-
-	line = tty->index;
-	if ((line < 0) || (line >= NR_PORTS))
-		return -ENODEV;
-	info = mcfrs_table + line;
-	if (serial_paranoia_check(info, tty->name, "mcfrs_open"))
-		return -ENODEV;
-#ifdef SERIAL_DEBUG_OPEN
-	printk("mcfrs_open %s, count = %d\n", tty->name, info->count);
-#endif
-	info->count++;
-	tty->driver_data = info;
-	info->port.tty = tty;
-
-	/*
-	 * Start up serial port
-	 */
-	retval = startup(info);
-	if (retval)
-		return retval;
-
-	retval = block_til_ready(tty, filp, info);
-	if (retval) {
-#ifdef SERIAL_DEBUG_OPEN
-		printk("mcfrs_open returning after block_til_ready with %d\n",
-		       retval);
-#endif
-		return retval;
-	}
-
-#ifdef SERIAL_DEBUG_OPEN
-	printk("mcfrs_open %s successful...\n", tty->name);
-#endif
-	return 0;
-}
-
-/*
- *	Based on the line number set up the internal interrupt stuff.
- */
-static void mcfrs_irqinit(struct mcf_serial *info)
-{
-#if defined(CONFIG_M5272)
-	volatile unsigned long	*icrp;
-	volatile unsigned long	*portp;
-	volatile unsigned char	*uartp;
-
-	uartp = info->addr;
-	icrp = (volatile unsigned long *) (MCF_MBAR + MCFSIM_ICR2);
-
-	switch (info->line) {
-	case 0:
-		*icrp = 0xe0000000;
-		break;
-	case 1:
-		*icrp = 0x0e000000;
-		break;
-	default:
-		printk("MCFRS: don't know how to handle UART %d interrupt?\n",
-			info->line);
-		return;
-	}
-
-	/* Enable the output lines for the serial ports */
-	portp = (volatile unsigned long *) (MCF_MBAR + MCFSIM_PBCNT);
-	*portp = (*portp & ~0x000000ff) | 0x00000055;
-	portp = (volatile unsigned long *) (MCF_MBAR + MCFSIM_PDCNT);
-	*portp = (*portp & ~0x000003fc) | 0x000002a8;
-#elif defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x)
-	volatile unsigned char *icrp, *uartp;
-	volatile unsigned long *imrp;
-
-	uartp = info->addr;
-
-	icrp = (volatile unsigned char *) (MCF_MBAR + MCFICM_INTC0 +
-		MCFINTC_ICR0 + MCFINT_UART0 + info->line);
-	*icrp = 0x30 + info->line; /* level 6, line based priority */
-
-	imrp = (volatile unsigned long *) (MCF_MBAR + MCFICM_INTC0 +
-		MCFINTC_IMRL);
-	*imrp &= ~((1 << (info->irq - MCFINT_VECBASE)) | 1);
-#if defined(CONFIG_M527x)
-	{
-		/*
-		 * External Pin Mask Setting & Enable External Pin for Interface
-		 * mrcbis@aliceposta.it
-        	 */
-		u16 *serpin_enable_mask;
-		serpin_enable_mask = (u16 *) (MCF_IPSBAR + MCF_GPIO_PAR_UART);
-		if (info->line == 0)
-			*serpin_enable_mask |= UART0_ENABLE_MASK;
-		else if (info->line == 1)
-			*serpin_enable_mask |= UART1_ENABLE_MASK;
-		else if (info->line == 2)
-			*serpin_enable_mask |= UART2_ENABLE_MASK;
-	}
-#endif
-#if defined(CONFIG_M528x)
-	/* make sure PUAPAR is set for UART0 and UART1 */
-	if (info->line < 2) {
-		volatile unsigned char *portp = (volatile unsigned char *) (MCF_MBAR + MCF5282_GPIO_PUAPAR);
-		*portp |= (0x03 << (info->line * 2));
-	}
-#endif
-#elif defined(CONFIG_M520x)
-	volatile unsigned char *icrp, *uartp;
-	volatile unsigned long *imrp;
-
-	uartp = info->addr;
-
-	icrp = (volatile unsigned char *) (MCF_MBAR + MCFICM_INTC0 +
-		MCFINTC_ICR0 + MCFINT_UART0 + info->line);
-	*icrp = 0x03;
-
-	imrp = (volatile unsigned long *) (MCF_MBAR + MCFICM_INTC0 +
-		MCFINTC_IMRL);
-	*imrp &= ~((1 << (info->irq - MCFINT_VECBASE)) | 1);
-	if (info->line < 2) {
-		unsigned short *uart_par;
-		uart_par = (unsigned short *)(MCF_IPSBAR + MCF_GPIO_PAR_UART);
-		if (info->line == 0)
-			*uart_par |=  MCF_GPIO_PAR_UART_PAR_UTXD0
-				  | MCF_GPIO_PAR_UART_PAR_URXD0;
-		else if (info->line == 1)
-			*uart_par |=  MCF_GPIO_PAR_UART_PAR_UTXD1
-				  | MCF_GPIO_PAR_UART_PAR_URXD1;
-		} else if (info->line == 2) {
-			unsigned char *feci2c_par;
-			feci2c_par = (unsigned char *)(MCF_IPSBAR +  MCF_GPIO_PAR_FECI2C);
-			*feci2c_par &= ~0x0F;
-			*feci2c_par |=  MCF_GPIO_PAR_FECI2C_PAR_SCL_UTXD2
-				    | MCF_GPIO_PAR_FECI2C_PAR_SDA_URXD2;
-		}
-#elif defined(CONFIG_M532x)
-	volatile unsigned char *uartp;
-	uartp = info->addr;
-	switch (info->line) {
-	case 0:
-		MCF_INTC0_ICR26 = 0x3;
-		MCF_INTC0_CIMR = 26;
-		/* GPIO initialization */
-		MCF_GPIO_PAR_UART |= 0x000F;
-		break;
-	case 1:
-		MCF_INTC0_ICR27 = 0x3;
-		MCF_INTC0_CIMR = 27;
-		/* GPIO initialization */
-		MCF_GPIO_PAR_UART |= 0x0FF0;
-		break;
-	case 2:
-		MCF_INTC0_ICR28 = 0x3;
-		MCF_INTC0_CIMR = 28;
-		/* GPIOs also must be initalized, depends on board */
-		break;
-	}
-#else
-	volatile unsigned char	*icrp, *uartp;
-
-	switch (info->line) {
-	case 0:
-		icrp = (volatile unsigned char *) (MCF_MBAR + MCFSIM_UART1ICR);
-		*icrp = /*MCFSIM_ICR_AUTOVEC |*/ MCFSIM_ICR_LEVEL6 |
-			MCFSIM_ICR_PRI1;
-		mcf_setimr(mcf_getimr() & ~MCFSIM_IMR_UART1);
-		break;
-	case 1:
-		icrp = (volatile unsigned char *) (MCF_MBAR + MCFSIM_UART2ICR);
-		*icrp = /*MCFSIM_ICR_AUTOVEC |*/ MCFSIM_ICR_LEVEL6 |
-			MCFSIM_ICR_PRI2;
-		mcf_setimr(mcf_getimr() & ~MCFSIM_IMR_UART2);
-		break;
-	default:
-		printk("MCFRS: don't know how to handle UART %d interrupt?\n",
-			info->line);
-		return;
-	}
-
-	uartp = info->addr;
-	uartp[MCFUART_UIVR] = info->irq;
-#endif
-
-	/* Clear mask, so no surprise interrupts. */
-	uartp[MCFUART_UIMR] = 0;
-
-	if (request_irq(info->irq, mcfrs_interrupt, IRQF_DISABLED,
-	    "ColdFire UART", NULL)) {
-		printk("MCFRS: Unable to attach ColdFire UART %d interrupt "
-			"vector=%d\n", info->line, info->irq);
-	}
-
-	return;
-}
-
-
-char *mcfrs_drivername = "ColdFire internal UART serial driver version 1.00\n";
-
-
-/*
- * Serial stats reporting...
- */
-int mcfrs_readproc(char *page, char **start, off_t off, int count,
-		         int *eof, void *data)
-{
-	struct mcf_serial	*info;
-	char			str[20];
-	int			len, sigs, i;
-
-	len = sprintf(page, mcfrs_drivername);
-	for (i = 0; (i < NR_PORTS); i++) {
-		info = &mcfrs_table[i];
-		len += sprintf((page + len), "%d: port:%x irq=%d baud:%d ",
-			i, (unsigned int) info->addr, info->irq, info->baud);
-		if (info->stats.rx || info->stats.tx)
-			len += sprintf((page + len), "tx:%d rx:%d ",
-			info->stats.tx, info->stats.rx);
-		if (info->stats.rxframing)
-			len += sprintf((page + len), "fe:%d ",
-			info->stats.rxframing);
-		if (info->stats.rxparity)
-			len += sprintf((page + len), "pe:%d ",
-			info->stats.rxparity);
-		if (info->stats.rxbreak)
-			len += sprintf((page + len), "brk:%d ",
-			info->stats.rxbreak);
-		if (info->stats.rxoverrun)
-			len += sprintf((page + len), "oe:%d ",
-			info->stats.rxoverrun);
-
-		str[0] = str[1] = 0;
-		if ((sigs = mcfrs_getsignals(info))) {
-			if (sigs & TIOCM_RTS)
-				strcat(str, "|RTS");
-			if (sigs & TIOCM_CTS)
-				strcat(str, "|CTS");
-			if (sigs & TIOCM_DTR)
-				strcat(str, "|DTR");
-			if (sigs & TIOCM_CD)
-				strcat(str, "|CD");
-		}
-
-		len += sprintf((page + len), "%s\n", &str[1]);
-	}
-
-	return(len);
-}
-
-
-/* Finally, routines used to initialize the serial driver. */
-
-static void show_serial_version(void)
-{
-	printk(mcfrs_drivername);
-}
-
-static const struct tty_operations mcfrs_ops = {
-	.open = mcfrs_open,
-	.close = mcfrs_close,
-	.write = mcfrs_write,
-	.flush_chars = mcfrs_flush_chars,
-	.write_room = mcfrs_write_room,
-	.chars_in_buffer = mcfrs_chars_in_buffer,
-	.flush_buffer = mcfrs_flush_buffer,
-	.ioctl = mcfrs_ioctl,
-	.throttle = mcfrs_throttle,
-	.unthrottle = mcfrs_unthrottle,
-	.set_termios = mcfrs_set_termios,
-	.stop = mcfrs_stop,
-	.start = mcfrs_start,
-	.hangup = mcfrs_hangup,
-	.read_proc = mcfrs_readproc,
-	.wait_until_sent = mcfrs_wait_until_sent,
- 	.tiocmget = mcfrs_tiocmget,
-	.tiocmset = mcfrs_tiocmset,
-};
-
-/* mcfrs_init inits the driver */
-static int __init
-mcfrs_init(void)
-{
-	struct mcf_serial	*info;
-	unsigned long		flags;
-	int			i;
-
-	/* Setup base handler, and timer table. */
-#ifdef MCFPP_DCD0
-	init_timer(&mcfrs_timer_struct);
-	mcfrs_timer_struct.function = mcfrs_timer;
-	mcfrs_timer_struct.data = 0;
-	mcfrs_timer_struct.expires = jiffies + HZ/25;
-	add_timer(&mcfrs_timer_struct);
-	mcfrs_ppstatus = mcf_getppdata() & (MCFPP_DCD0 | MCFPP_DCD1);
-#endif
-	mcfrs_serial_driver = alloc_tty_driver(NR_PORTS);
-	if (!mcfrs_serial_driver)
-		return -ENOMEM;
-
-	show_serial_version();
-
-	/* Initialize the tty_driver structure */
-	mcfrs_serial_driver->owner = THIS_MODULE;
-	mcfrs_serial_driver->name = "ttyS";
-	mcfrs_serial_driver->driver_name = "mcfserial";
-	mcfrs_serial_driver->major = TTY_MAJOR;
-	mcfrs_serial_driver->minor_start = 64;
-	mcfrs_serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
-	mcfrs_serial_driver->subtype = SERIAL_TYPE_NORMAL;
-	mcfrs_serial_driver->init_termios = tty_std_termios;
-
-	mcfrs_serial_driver->init_termios.c_cflag =
-		mcfrs_console_cbaud | CS8 | CREAD | HUPCL | CLOCAL;
-	mcfrs_serial_driver->flags = TTY_DRIVER_REAL_RAW;
-
-	tty_set_operations(mcfrs_serial_driver, &mcfrs_ops);
-
-	if (tty_register_driver(mcfrs_serial_driver)) {
-		printk("MCFRS: Couldn't register serial driver\n");
-		put_tty_driver(mcfrs_serial_driver);
-		return(-EBUSY);
-	}
-
-	local_irq_save(flags);
-
-	/*
-	 *	Configure all the attached serial ports.
-	 */
-	for (i = 0, info = mcfrs_table; (i < NR_PORTS); i++, info++) {
-		info->magic = SERIAL_MAGIC;
-		info->line = i;
-		info->port.tty = NULL;
-		info->custom_divisor = 16;
-		info->close_delay = 50;
-		info->closing_wait = 3000;
-		info->x_char = 0;
-		info->event = 0;
-		info->count = 0;
-		info->blocked_open = 0;
-		INIT_WORK(&info->tqueue, mcfrs_offintr);
-		INIT_WORK(&info->tqueue_hangup, do_serial_hangup);
-		init_waitqueue_head(&info->open_wait);
-		init_waitqueue_head(&info->close_wait);
-
-		info->imr = 0;
-		mcfrs_setsignals(info, 0, 0);
-		mcfrs_irqinit(info);
-
-		printk("ttyS%d at 0x%04x (irq = %d)", info->line,
-			(unsigned int) info->addr, info->irq);
-		printk(" is a builtin ColdFire UART\n");
-	}
-
-	local_irq_restore(flags);
-	return 0;
-}
-
-module_init(mcfrs_init);
-
-/****************************************************************************/
-/*                          Serial Console                                  */
-/****************************************************************************/
-
-/*
- *	Quick and dirty UART initialization, for console output.
- */
-
-void mcfrs_init_console(void)
-{
-	volatile unsigned char	*uartp;
-	unsigned int		clk;
-
-	/*
-	 *	Reset UART, get it into known state...
-	 */
-	uartp = (volatile unsigned char *) (MCF_MBAR +
-		(mcfrs_console_port ? MCFUART_BASE2 : MCFUART_BASE1));
-
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX;  /* reset RX */
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETTX;  /* reset TX */
-	uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETMRPTR;  /* reset MR pointer */
-
-	/*
-	 * Set port for defined baud , 8 data bits, 1 stop bit, no parity.
-	 */
-	uartp[MCFUART_UMR] = MCFUART_MR1_PARITYNONE | MCFUART_MR1_CS8;
-	uartp[MCFUART_UMR] = MCFUART_MR2_STOP1;
-
-#ifdef	CONFIG_M5272
-{
-	/*
-	 * For the MCF5272, also compute the baudrate fraction.
-	 */
-	int fraction = MCF_BUSCLK - (clk * 32 * mcfrs_console_baud);
-	fraction *= 16;
-	fraction /= (32 * mcfrs_console_baud);
-	uartp[MCFUART_UFPD] = (fraction & 0xf);		/* set fraction */
-	clk = (MCF_BUSCLK / mcfrs_console_baud) / 32;
-}
-#else
-	clk = ((MCF_BUSCLK / mcfrs_console_baud) + 16) / 32; /* set baud */
-#endif
-
-	uartp[MCFUART_UBG1] = (clk & 0xff00) >> 8;  /* set msb baud */
-	uartp[MCFUART_UBG2] = (clk & 0xff);  /* set lsb baud */
-	uartp[MCFUART_UCSR] = MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER;
-	uartp[MCFUART_UCR] = MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE;
-
-	mcfrs_console_inited++;
-	return;
-}
-
-
-/*
- *	Setup for console. Argument comes from the boot command line.
- */
-
-int mcfrs_console_setup(struct console *cp, char *arg)
-{
-	int		i, n = CONSOLE_BAUD_RATE;
-
-	if (!cp)
-		return(-1);
-
-	if (!strncmp(cp->name, "ttyS", 4))
-		mcfrs_console_port = cp->index;
-	else if (!strncmp(cp->name, "cua", 3))
-		mcfrs_console_port = cp->index;
-	else
-		return(-1);
-
-	if (arg)
-		n = simple_strtoul(arg,NULL,0);
-	for (i = 0; i < MCFRS_BAUD_TABLE_SIZE; i++)
-		if (mcfrs_baud_table[i] == n)
-			break;
-	if (i < MCFRS_BAUD_TABLE_SIZE) {
-		mcfrs_console_baud = n;
-		mcfrs_console_cbaud = 0;
-		if (i > 15) {
-			mcfrs_console_cbaud |= CBAUDEX;
-			i -= 15;
-		}
-		mcfrs_console_cbaud |= i;
-	}
-	mcfrs_init_console(); /* make sure baud rate changes */
-	return(0);
-}
-
-
-static struct tty_driver *mcfrs_console_device(struct console *c, int *index)
-{
-	*index = c->index;
-	return mcfrs_serial_driver;
-}
-
-
-/*
- *	Output a single character, using UART polled mode.
- *	This is used for console output.
- */
-
-int mcfrs_put_char(char ch)
-{
-	volatile unsigned char	*uartp;
-	unsigned long		flags;
-	int			i;
-
-	uartp = (volatile unsigned char *) (MCF_MBAR +
-		(mcfrs_console_port ? MCFUART_BASE2 : MCFUART_BASE1));
-
-	local_irq_save(flags);
-	for (i = 0; (i < 0x10000); i++) {
-		if (uartp[MCFUART_USR] & MCFUART_USR_TXREADY)
-			break;
-	}
-	if (i < 0x10000) {
-		uartp[MCFUART_UTB] = ch;
-		for (i = 0; (i < 0x10000); i++)
-			if (uartp[MCFUART_USR] & MCFUART_USR_TXEMPTY)
-				break;
-	}
-	if (i >= 0x10000)
-		mcfrs_init_console(); /* try and get it back */
-	local_irq_restore(flags);
-
-	return 1;
-}
-
-
-/*
- * rs_console_write is registered for printk output.
- */
-
-void mcfrs_console_write(struct console *cp, const char *p, unsigned len)
-{
-	if (!mcfrs_console_inited)
-		mcfrs_init_console();
-	while (len-- > 0) {
-		if (*p == '\n')
-			mcfrs_put_char('\r');
-		mcfrs_put_char(*p++);
-	}
-}
-
-/*
- * declare our consoles
- */
-
-struct console mcfrs_console = {
-	.name		= "ttyS",
-	.write		= mcfrs_console_write,
-	.device		= mcfrs_console_device,
-	.setup		= mcfrs_console_setup,
-	.flags		= CON_PRINTBUFFER,
-	.index		= -1,
-};
-
-static int __init mcfrs_console_init(void)
-{
-	register_console(&mcfrs_console);
-	return 0;
-}
-
-console_initcall(mcfrs_console_init);
-
-/****************************************************************************/
diff --git a/drivers/serial/mcfserial.h b/drivers/serial/mcfserial.h
deleted file mode 100644
index 56420e2cb110..000000000000
--- a/drivers/serial/mcfserial.h
+++ /dev/null
@@ -1,74 +0,0 @@
-/*
- * mcfserial.c -- serial driver for ColdFire internal UARTS.
- *
- * Copyright (c) 1999 Greg Ungerer <gerg@snapgear.com>
- * Copyright (c) 2000-2001 Lineo, Inc. <www.lineo.com>
- * Copyright (c) 2002 SnapGear Inc., <www.snapgear.com>
- *
- * Based on code from 68332serial.c which was:
- *
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
- * Copyright (C) 1998 TSHG
- * Copyright (c) 1999 Rt-Control Inc. <jeff@uclinux.org>
- */ 
-#ifndef _MCF_SERIAL_H
-#define _MCF_SERIAL_H
-
-#include <linux/serial.h>
-
-#ifdef __KERNEL__
-
-/*
- *	Define a local serial stats structure.
- */
-
-struct mcf_stats {
-	unsigned int	rx;
-	unsigned int	tx;
-	unsigned int	rxbreak;
-	unsigned int	rxframing;
-	unsigned int	rxparity;
-	unsigned int	rxoverrun;
-};
-
-
-/*
- * This is our internal structure for each serial port's state.
- * Each serial port has one of these structures associated with it.
- */
-
-struct mcf_serial {
-	int			magic;
-	volatile unsigned char	*addr;		/* UART memory address */
-	int			irq;
-	int			flags; 		/* defined in tty.h */
-	int			type; 		/* UART type */
-	struct tty_struct 	*tty;
-	unsigned char		imr;		/* Software imr register */
-	unsigned int		baud;
-	int			sigs;
-	int			custom_divisor;
-	int			x_char;	/* xon/xoff character */
-	int			baud_base;
-	int			close_delay;
-	unsigned short		closing_wait;
-	unsigned short		closing_wait2;
-	unsigned long		event;
-	int			line;
-	int			count;	    /* # of fd on device */
-	int			blocked_open; /* # of blocked opens */
-	unsigned char 		*xmit_buf;
-	int			xmit_head;
-	int			xmit_tail;
-	int			xmit_cnt;
-	struct mcf_stats	stats;
-	struct work_struct	tqueue;
-	struct work_struct	tqueue_hangup;
-	wait_queue_head_t	open_wait;
-	wait_queue_head_t	close_wait;
-
-};
-
-#endif /* __KERNEL__ */
-
-#endif /* _MCF_SERIAL_H */
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index 36126070d9af..6117d3db0b66 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -72,13 +72,8 @@
 #include <linux/console.h>
 #include <linux/delay.h>
 #include <linux/io.h>
-
-#if defined(CONFIG_PPC_MERGE)
 #include <linux/of.h>
 #include <linux/of_platform.h>
-#else
-#include <linux/platform_device.h>
-#endif
 
 #include <asm/mpc52xx.h>
 #include <asm/mpc512x.h>
@@ -107,12 +102,11 @@ static struct uart_port mpc52xx_uart_ports[MPC52xx_PSC_MAXNUM];
 	 *        it's cleared, then a memset(...,0,...) should be added to
 	 *        the console_init
 	 */
-#if defined(CONFIG_PPC_MERGE)
+
 /* lookup table for matching device nodes to index numbers */
 static struct device_node *mpc52xx_uart_nodes[MPC52xx_PSC_MAXNUM];
 
 static void mpc52xx_uart_of_enumerate(void);
-#endif
 
 
 #define PSC(port) ((struct mpc52xx_psc __iomem *)((port)->membase))
@@ -255,17 +249,12 @@ static void mpc52xx_psc_cw_restore_ints(struct uart_port *port)
 /* Search for bus-frequency property in this node or a parent */
 static unsigned long mpc52xx_getuartclk(void *p)
 {
-#if defined(CONFIG_PPC_MERGE)
 	/*
 	 * 5200 UARTs have a / 32 prescaler
 	 * but the generic serial code assumes 16
 	 * so return ipb freq / 2
 	 */
 	return mpc52xx_find_ipb_freq(p) / 2;
-#else
-	pr_debug("unexpected call to mpc52xx_getuartclk with arch/ppc\n");
-	return NULL;
-#endif
 }
 
 static struct psc_ops mpc52xx_psc_ops = {
@@ -886,10 +875,6 @@ mpc52xx_console_get_options(struct uart_port *port,
 
 	/* CT{U,L}R are write-only ! */
 	*baud = CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD;
-#if !defined(CONFIG_PPC_MERGE)
-	if (__res.bi_baudrate)
-		*baud = __res.bi_baudrate;
-#endif
 
 	/* Parse them */
 	switch (mr1 & MPC52xx_PSC_MODE_BITS_MASK) {
@@ -946,42 +931,6 @@ mpc52xx_console_write(struct console *co, const char *s, unsigned int count)
 	psc_ops->cw_restore_ints(port);
 }
 
-#if !defined(CONFIG_PPC_MERGE)
-static int __init
-mpc52xx_console_setup(struct console *co, char *options)
-{
-	struct uart_port *port = &mpc52xx_uart_ports[co->index];
-
-	int baud = CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD;
-	int bits = 8;
-	int parity = 'n';
-	int flow = 'n';
-
-	if (co->index < 0 || co->index >= MPC52xx_PSC_MAXNUM)
-		return -EINVAL;
-
-	/* Basic port init. Needed since we use some uart_??? func before
-	 * real init for early access */
-	spin_lock_init(&port->lock);
-	port->uartclk	= __res.bi_ipbfreq / 2; /* Look at CTLR doc */
-	port->ops	= &mpc52xx_uart_ops;
-	port->mapbase	= MPC52xx_PA(MPC52xx_PSCx_OFFSET(co->index+1));
-
-	/* We ioremap ourself */
-	port->membase = ioremap(port->mapbase, MPC52xx_PSC_SIZE);
-	if (port->membase == NULL)
-		return -EINVAL;
-
-	/* Setup the port parameters accoding to options */
-	if (options)
-		uart_parse_options(options, &baud, &parity, &bits, &flow);
-	else
-		mpc52xx_console_get_options(port, &baud, &parity, &bits, &flow);
-
-	return uart_set_options(port, co, baud, parity, bits, flow);
-}
-
-#else
 
 static int __init
 mpc52xx_console_setup(struct console *co, char *options)
@@ -1053,7 +1002,6 @@ mpc52xx_console_setup(struct console *co, char *options)
 
 	return uart_set_options(port, co, baud, parity, bits, flow);
 }
-#endif /* defined(CONFIG_PPC_MERGE) */
 
 
 static struct uart_driver mpc52xx_uart_driver;
@@ -1072,9 +1020,7 @@ static struct console mpc52xx_console = {
 static int __init
 mpc52xx_console_init(void)
 {
-#if defined(CONFIG_PPC_MERGE)
 	mpc52xx_uart_of_enumerate();
-#endif
 	register_console(&mpc52xx_console);
 	return 0;
 }
@@ -1100,115 +1046,6 @@ static struct uart_driver mpc52xx_uart_driver = {
 	.cons		= MPC52xx_PSC_CONSOLE,
 };
 
-
-#if !defined(CONFIG_PPC_MERGE)
-/* ======================================================================== */
-/* Platform Driver                                                          */
-/* ======================================================================== */
-
-static int __devinit
-mpc52xx_uart_probe(struct platform_device *dev)
-{
-	struct resource *res = dev->resource;
-
-	struct uart_port *port = NULL;
-	int i, idx, ret;
-
-	/* Check validity & presence */
-	idx = dev->id;
-	if (idx < 0 || idx >= MPC52xx_PSC_MAXNUM)
-		return -EINVAL;
-
-	if (!mpc52xx_match_psc_function(idx, "uart"))
-		return -ENODEV;
-
-	/* Init the port structure */
-	port = &mpc52xx_uart_ports[idx];
-
-	spin_lock_init(&port->lock);
-	port->uartclk	= __res.bi_ipbfreq / 2; /* Look at CTLR doc */
-	port->fifosize	= 512;
-	port->iotype	= UPIO_MEM;
-	port->flags	= UPF_BOOT_AUTOCONF |
-			  (uart_console(port) ? 0 : UPF_IOREMAP);
-	port->line	= idx;
-	port->ops	= &mpc52xx_uart_ops;
-	port->dev	= &dev->dev;
-
-	/* Search for IRQ and mapbase */
-	for (i = 0 ; i < dev->num_resources ; i++, res++) {
-		if (res->flags & IORESOURCE_MEM)
-			port->mapbase = res->start;
-		else if (res->flags & IORESOURCE_IRQ)
-			port->irq = res->start;
-	}
-	if (!port->irq || !port->mapbase)
-		return -EINVAL;
-
-	/* Add the port to the uart sub-system */
-	ret = uart_add_one_port(&mpc52xx_uart_driver, port);
-	if (!ret)
-		platform_set_drvdata(dev, (void *)port);
-
-	return ret;
-}
-
-static int
-mpc52xx_uart_remove(struct platform_device *dev)
-{
-	struct uart_port *port = (struct uart_port *) platform_get_drvdata(dev);
-
-	platform_set_drvdata(dev, NULL);
-
-	if (port)
-		uart_remove_one_port(&mpc52xx_uart_driver, port);
-
-	return 0;
-}
-
-#ifdef CONFIG_PM
-static int
-mpc52xx_uart_suspend(struct platform_device *dev, pm_message_t state)
-{
-	struct uart_port *port = (struct uart_port *) platform_get_drvdata(dev);
-
-	if (port)
-		uart_suspend_port(&mpc52xx_uart_driver, port);
-
-	return 0;
-}
-
-static int
-mpc52xx_uart_resume(struct platform_device *dev)
-{
-	struct uart_port *port = (struct uart_port *) platform_get_drvdata(dev);
-
-	if (port)
-		uart_resume_port(&mpc52xx_uart_driver, port);
-
-	return 0;
-}
-#endif
-
-/* work with hotplug and coldplug */
-MODULE_ALIAS("platform:mpc52xx-psc");
-
-static struct platform_driver mpc52xx_uart_platform_driver = {
-	.probe		= mpc52xx_uart_probe,
-	.remove		= mpc52xx_uart_remove,
-#ifdef CONFIG_PM
-	.suspend	= mpc52xx_uart_suspend,
-	.resume		= mpc52xx_uart_resume,
-#endif
-	.driver		= {
-		.owner	= THIS_MODULE,
-		.name	= "mpc52xx-psc",
-	},
-};
-#endif /* !defined(CONFIG_PPC_MERGE) */
-
-
-#if defined(CONFIG_PPC_MERGE)
 /* ======================================================================== */
 /* OF Platform Driver                                                       */
 /* ======================================================================== */
@@ -1402,7 +1239,6 @@ static struct of_platform_driver mpc52xx_uart_of_driver = {
 		.name	= "mpc52xx-psc-uart",
 	},
 };
-#endif /* defined(CONFIG_PPC_MERGE) */
 
 
 /* ======================================================================== */
@@ -1423,7 +1259,6 @@ mpc52xx_uart_init(void)
 		return ret;
 	}
 
-#if defined(CONFIG_PPC_MERGE)
 	mpc52xx_uart_of_enumerate();
 
 	ret = of_register_platform_driver(&mpc52xx_uart_of_driver);
@@ -1433,16 +1268,6 @@ mpc52xx_uart_init(void)
 		uart_unregister_driver(&mpc52xx_uart_driver);
 		return ret;
 	}
-#else
-	psc_ops = &mpc52xx_psc_ops;
-	ret = platform_driver_register(&mpc52xx_uart_platform_driver);
-	if (ret) {
-		printk(KERN_ERR "%s: platform_driver_register failed (%i)\n",
-		       __FILE__, ret);
-		uart_unregister_driver(&mpc52xx_uart_driver);
-		return ret;
-	}
-#endif
 
 	return 0;
 }
@@ -1450,11 +1275,7 @@ mpc52xx_uart_init(void)
 static void __exit
 mpc52xx_uart_exit(void)
 {
-#if defined(CONFIG_PPC_MERGE)
 	of_unregister_platform_driver(&mpc52xx_uart_of_driver);
-#else
-	platform_driver_unregister(&mpc52xx_uart_platform_driver);
-#endif
 	uart_unregister_driver(&mpc52xx_uart_driver);
 }
 
diff --git a/drivers/serial/pxa.c b/drivers/serial/pxa.c
index f7a0d37c4221..abc00be55433 100644
--- a/drivers/serial/pxa.c
+++ b/drivers/serial/pxa.c
@@ -534,6 +534,11 @@ serial_pxa_set_termios(struct uart_port *port, struct ktermios *termios,
 
 	serial_out(up, UART_IER, up->ier);
 
+	if (termios->c_cflag & CRTSCTS)
+		up->mcr |= UART_MCR_AFE;
+	else
+		up->mcr &= ~UART_MCR_AFE;
+
 	serial_out(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
 	serial_out(up, UART_DLL, quot & 0xff);		/* LS of divisor */
 	serial_out(up, UART_DLM, quot >> 8);		/* MS of divisor */
diff --git a/drivers/serial/s3c2400.c b/drivers/serial/s3c2400.c
index c8b4266ac35f..4873f2978bd2 100644
--- a/drivers/serial/s3c2400.c
+++ b/drivers/serial/s3c2400.c
@@ -19,7 +19,7 @@
 
 #include <mach/hardware.h>
 
-#include <asm/plat-s3c/regs-serial.h>
+#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 
 #include "samsung.h"
diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c
index 40a2531b5541..87c182ef71b8 100644
--- a/drivers/serial/s3c2410.c
+++ b/drivers/serial/s3c2410.c
@@ -21,7 +21,7 @@
 #include <asm/irq.h>
 #include <mach/hardware.h>
 
-#include <asm/plat-s3c/regs-serial.h>
+#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 
 #include "samsung.h"
diff --git a/drivers/serial/s3c2412.c b/drivers/serial/s3c2412.c
index d0170319c729..fd017b375568 100644
--- a/drivers/serial/s3c2412.c
+++ b/drivers/serial/s3c2412.c
@@ -21,7 +21,7 @@
 #include <asm/irq.h>
 #include <mach/hardware.h>
 
-#include <asm/plat-s3c/regs-serial.h>
+#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 
 #include "samsung.h"
diff --git a/drivers/serial/s3c2440.c b/drivers/serial/s3c2440.c
index d4a2b17b2498..317d239ab740 100644
--- a/drivers/serial/s3c2440.c
+++ b/drivers/serial/s3c2440.c
@@ -21,7 +21,7 @@
 #include <asm/irq.h>
 #include <mach/hardware.h>
 
-#include <asm/plat-s3c/regs-serial.h>
+#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 
 #include "samsung.h"
diff --git a/drivers/serial/samsung.c b/drivers/serial/samsung.c
index 5a88b3f9fe9b..1e219d3d0352 100644
--- a/drivers/serial/samsung.c
+++ b/drivers/serial/samsung.c
@@ -47,7 +47,7 @@
 
 #include <mach/hardware.h>
 
-#include <asm/plat-s3c/regs-serial.h>
+#include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 
 #include "samsung.h"
diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c
index f977c98cfa95..6bdf3362e3b1 100644
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -2051,7 +2051,8 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *port)
 					"transmitter\n",
 			       port->dev ? port->dev->bus_id : "",
 			       port->dev ? ": " : "",
-			       drv->dev_name, port->line);
+			       drv->dev_name,
+			       drv->tty_driver->name_base + port->line);
 
 		ops->shutdown(port);
 	}
@@ -2154,12 +2155,11 @@ uart_report_port(struct uart_driver *drv, struct uart_port *port)
 
 	switch (port->iotype) {
 	case UPIO_PORT:
-		snprintf(address, sizeof(address),
-			 "I/O 0x%x", port->iobase);
+		snprintf(address, sizeof(address), "I/O 0x%lx", port->iobase);
 		break;
 	case UPIO_HUB6:
 		snprintf(address, sizeof(address),
-			 "I/O 0x%x offset 0x%x", port->iobase, port->hub6);
+			 "I/O 0x%lx offset 0x%x", port->iobase, port->hub6);
 		break;
 	case UPIO_MEM:
 	case UPIO_MEM32:
@@ -2177,7 +2177,9 @@ uart_report_port(struct uart_driver *drv, struct uart_port *port)
 	printk(KERN_INFO "%s%s%s%d at %s (irq = %d) is a %s\n",
 	       port->dev ? port->dev->bus_id : "",
 	       port->dev ? ": " : "",
-	       drv->dev_name, port->line, address, port->irq, uart_type(port));
+	       drv->dev_name,
+	       drv->tty_driver->name_base + port->line,
+	       address, port->irq, uart_type(port));
 }
 
 static void
diff --git a/drivers/serial/serial_cs.c b/drivers/serial/serial_cs.c
index 164d2a42eb59..7546aa887fa7 100644
--- a/drivers/serial/serial_cs.c
+++ b/drivers/serial/serial_cs.c
@@ -431,131 +431,103 @@ first_tuple(struct pcmcia_device *handle, tuple_t * tuple, cisparse_t * parse)
 {
 	int i;
 	i = pcmcia_get_first_tuple(handle, tuple);
-	if (i != CS_SUCCESS)
-		return CS_NO_MORE_ITEMS;
-	i = pcmcia_get_tuple_data(handle, tuple);
-	if (i != CS_SUCCESS)
+	if (i != 0)
 		return i;
-	return pcmcia_parse_tuple(handle, tuple, parse);
-}
-
-static int
-next_tuple(struct pcmcia_device *handle, tuple_t * tuple, cisparse_t * parse)
-{
-	int i;
-	i = pcmcia_get_next_tuple(handle, tuple);
-	if (i != CS_SUCCESS)
-		return CS_NO_MORE_ITEMS;
 	i = pcmcia_get_tuple_data(handle, tuple);
-	if (i != CS_SUCCESS)
+	if (i != 0)
 		return i;
-	return pcmcia_parse_tuple(handle, tuple, parse);
+	return pcmcia_parse_tuple(tuple, parse);
 }
 
 /*====================================================================*/
 
-static int simple_config(struct pcmcia_device *link)
+static int simple_config_check(struct pcmcia_device *p_dev,
+			       cistpl_cftable_entry_t *cf,
+			       cistpl_cftable_entry_t *dflt,
+			       unsigned int vcc,
+			       void *priv_data)
 {
-	static const unsigned int base[5] = { 0x3f8, 0x2f8, 0x3e8, 0x2e8, 0x0 };
 	static const int size_table[2] = { 8, 16 };
-	struct serial_info *info = link->priv;
-	struct serial_cfg_mem *cfg_mem;
-	tuple_t *tuple;
-	u_char *buf;
-	cisparse_t *parse;
-	cistpl_cftable_entry_t *cf;
-	config_info_t config;
-	int i, j, try;
-	int s;
+	int *try = priv_data;
+
+	if (cf->vpp1.present & (1 << CISTPL_POWER_VNOM))
+		p_dev->conf.Vpp =
+			cf->vpp1.param[CISTPL_POWER_VNOM] / 10000;
+
+	if ((cf->io.nwin > 0) && (cf->io.win[0].len == size_table[(*try >> 1)])
+	    && (cf->io.win[0].base != 0)) {
+		p_dev->io.BasePort1 = cf->io.win[0].base;
+		p_dev->io.IOAddrLines = ((*try & 0x1) == 0) ?
+			16 : cf->io.flags & CISTPL_IO_LINES_MASK;
+		if (!pcmcia_request_io(p_dev, &p_dev->io))
+			return 0;
+	}
+	return -EINVAL;
+}
 
-	cfg_mem = kmalloc(sizeof(struct serial_cfg_mem), GFP_KERNEL);
-	if (!cfg_mem)
-		return -1;
+static int simple_config_check_notpicky(struct pcmcia_device *p_dev,
+					cistpl_cftable_entry_t *cf,
+					cistpl_cftable_entry_t *dflt,
+					unsigned int vcc,
+					void *priv_data)
+{
+	static const unsigned int base[5] = { 0x3f8, 0x2f8, 0x3e8, 0x2e8, 0x0 };
+	int j;
+
+	if ((cf->io.nwin > 0) && ((cf->io.flags & CISTPL_IO_LINES_MASK) <= 3)) {
+		for (j = 0; j < 5; j++) {
+			p_dev->io.BasePort1 = base[j];
+			p_dev->io.IOAddrLines = base[j] ? 16 : 3;
+			if (!pcmcia_request_io(p_dev, &p_dev->io))
+				return 0;
+		}
+	}
+	return -ENODEV;
+}
 
-	tuple = &cfg_mem->tuple;
-	parse = &cfg_mem->parse;
-	cf = &parse->cftable_entry;
-	buf = cfg_mem->buf;
+static int simple_config(struct pcmcia_device *link)
+{
+	struct serial_info *info = link->priv;
+	int i = -ENODEV, try;
 
 	/* If the card is already configured, look up the port and irq */
-	i = pcmcia_get_configuration_info(link, &config);
-	if ((i == CS_SUCCESS) && (config.Attributes & CONF_VALID_CLIENT)) {
+	if (link->function_config) {
 		unsigned int port = 0;
-		if ((config.BasePort2 != 0) && (config.NumPorts2 == 8)) {
-			port = config.BasePort2;
+		if ((link->io.BasePort2 != 0) &&
+		    (link->io.NumPorts2 == 8)) {
+			port = link->io.BasePort2;
 			info->slave = 1;
 		} else if ((info->manfid == MANFID_OSITECH) &&
-			   (config.NumPorts1 == 0x40)) {
-			port = config.BasePort1 + 0x28;
+			   (link->io.NumPorts1 == 0x40)) {
+			port = link->io.BasePort1 + 0x28;
 			info->slave = 1;
 		}
 		if (info->slave) {
-			kfree(cfg_mem);
-			return setup_serial(link, info, port, config.AssignedIRQ);
+			return setup_serial(link, info, port,
+					    link->irq.AssignedIRQ);
 		}
 	}
 
-	/* First pass: look for a config entry that looks normal. */
-	tuple->TupleData = (cisdata_t *) buf;
-	tuple->TupleOffset = 0;
-	tuple->TupleDataMax = 255;
-	tuple->Attributes = 0;
-	tuple->DesiredTuple = CISTPL_CFTABLE_ENTRY;
-	/* Two tries: without IO aliases, then with aliases */
-	for (s = 0; s < 2; s++) {
-		for (try = 0; try < 2; try++) {
-			i = first_tuple(link, tuple, parse);
-			while (i != CS_NO_MORE_ITEMS) {
-				if (i != CS_SUCCESS)
-					goto next_entry;
-				if (cf->vpp1.present & (1 << CISTPL_POWER_VNOM))
-					link->conf.Vpp =
-					    cf->vpp1.param[CISTPL_POWER_VNOM] / 10000;
-				if ((cf->io.nwin > 0) && (cf->io.win[0].len == size_table[s]) &&
-					    (cf->io.win[0].base != 0)) {
-					link->conf.ConfigIndex = cf->index;
-					link->io.BasePort1 = cf->io.win[0].base;
-					link->io.IOAddrLines = (try == 0) ?
-					    16 : cf->io.flags & CISTPL_IO_LINES_MASK;
-					i = pcmcia_request_io(link, &link->io);
-					if (i == CS_SUCCESS)
-						goto found_port;
-				}
-next_entry:
-				i = next_tuple(link, tuple, parse);
-			}
-		}
-	}
+	/* First pass: look for a config entry that looks normal.
+	 * Two tries: without IO aliases, then with aliases */
+	for (try = 0; try < 4; try++)
+		if (!pcmcia_loop_config(link, simple_config_check, &try))
+			goto found_port;
+
 	/* Second pass: try to find an entry that isn't picky about
 	   its base address, then try to grab any standard serial port
 	   address, and finally try to get any free port. */
-	i = first_tuple(link, tuple, parse);
-	while (i != CS_NO_MORE_ITEMS) {
-		if ((i == CS_SUCCESS) && (cf->io.nwin > 0) &&
-		    ((cf->io.flags & CISTPL_IO_LINES_MASK) <= 3)) {
-			link->conf.ConfigIndex = cf->index;
-			for (j = 0; j < 5; j++) {
-				link->io.BasePort1 = base[j];
-				link->io.IOAddrLines = base[j] ? 16 : 3;
-				i = pcmcia_request_io(link, &link->io);
-				if (i == CS_SUCCESS)
-					goto found_port;
-			}
-		}
-		i = next_tuple(link, tuple, parse);
-	}
+	if (!pcmcia_loop_config(link, simple_config_check_notpicky, NULL))
+		goto found_port;
 
-      found_port:
-	if (i != CS_SUCCESS) {
-		printk(KERN_NOTICE
-		       "serial_cs: no usable port range found, giving up\n");
-		cs_error(link, RequestIO, i);
-		kfree(cfg_mem);
-		return -1;
-	}
+	printk(KERN_NOTICE
+	       "serial_cs: no usable port range found, giving up\n");
+	cs_error(link, RequestIO, i);
+	return -1;
 
+found_port:
 	i = pcmcia_request_irq(link, &link->irq);
-	if (i != CS_SUCCESS) {
+	if (i != 0) {
 		cs_error(link, RequestIRQ, i);
 		link->irq.AssignedIRQ = 0;
 	}
@@ -569,88 +541,76 @@ next_entry:
 		info->quirk->config(link);
 
 	i = pcmcia_request_configuration(link, &link->conf);
-	if (i != CS_SUCCESS) {
+	if (i != 0) {
 		cs_error(link, RequestConfiguration, i);
-		kfree(cfg_mem);
 		return -1;
 	}
-	kfree(cfg_mem);
 	return setup_serial(link, info, link->io.BasePort1, link->irq.AssignedIRQ);
 }
 
-static int multi_config(struct pcmcia_device * link)
+static int multi_config_check(struct pcmcia_device *p_dev,
+			      cistpl_cftable_entry_t *cf,
+			      cistpl_cftable_entry_t *dflt,
+			      unsigned int vcc,
+			      void *priv_data)
 {
-	struct serial_info *info = link->priv;
-	struct serial_cfg_mem *cfg_mem;
-	tuple_t *tuple;
-	u_char *buf;
-	cisparse_t *parse;
-	cistpl_cftable_entry_t *cf;
-	int i, rc, base2 = 0;
+	int *base2 = priv_data;
+
+	/* The quad port cards have bad CIS's, so just look for a
+	   window larger than 8 ports and assume it will be right */
+	if ((cf->io.nwin == 1) && (cf->io.win[0].len > 8)) {
+		p_dev->io.BasePort1 = cf->io.win[0].base;
+		p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK;
+		if (!pcmcia_request_io(p_dev, &p_dev->io)) {
+			*base2 = p_dev->io.BasePort1 + 8;
+			return 0;
+		}
+	}
+	return -ENODEV;
+}
 
-	cfg_mem = kmalloc(sizeof(struct serial_cfg_mem), GFP_KERNEL);
-	if (!cfg_mem)
-		return -1;
-	tuple = &cfg_mem->tuple;
-	parse = &cfg_mem->parse;
-	cf = &parse->cftable_entry;
-	buf = cfg_mem->buf;
+static int multi_config_check_notpicky(struct pcmcia_device *p_dev,
+				       cistpl_cftable_entry_t *cf,
+				       cistpl_cftable_entry_t *dflt,
+				       unsigned int vcc,
+				       void *priv_data)
+{
+	int *base2 = priv_data;
+
+	if (cf->io.nwin == 2) {
+		p_dev->io.BasePort1 = cf->io.win[0].base;
+		p_dev->io.BasePort2 = cf->io.win[1].base;
+		p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK;
+		if (!pcmcia_request_io(p_dev, &p_dev->io)) {
+			*base2 = p_dev->io.BasePort2;
+			return 0;
+		}
+	}
+	return -ENODEV;
+}
 
-	tuple->TupleData = (cisdata_t *) buf;
-	tuple->TupleOffset = 0;
-	tuple->TupleDataMax = 255;
-	tuple->Attributes = 0;
-	tuple->DesiredTuple = CISTPL_CFTABLE_ENTRY;
+static int multi_config(struct pcmcia_device *link)
+{
+	struct serial_info *info = link->priv;
+	int i, base2 = 0;
 
 	/* First, look for a generic full-sized window */
 	link->io.NumPorts1 = info->multi * 8;
-	i = first_tuple(link, tuple, parse);
-	while (i != CS_NO_MORE_ITEMS) {
-		/* The quad port cards have bad CIS's, so just look for a
-		   window larger than 8 ports and assume it will be right */
-		if ((i == CS_SUCCESS) && (cf->io.nwin == 1) &&
-		    (cf->io.win[0].len > 8)) {
-			link->conf.ConfigIndex = cf->index;
-			link->io.BasePort1 = cf->io.win[0].base;
-			link->io.IOAddrLines =
-			    cf->io.flags & CISTPL_IO_LINES_MASK;
-			i = pcmcia_request_io(link, &link->io);
-			base2 = link->io.BasePort1 + 8;
-			if (i == CS_SUCCESS)
-				break;
-		}
-		i = next_tuple(link, tuple, parse);
-	}
-
-	/* If that didn't work, look for two windows */
-	if (i != CS_SUCCESS) {
+	if (pcmcia_loop_config(link, multi_config_check, &base2)) {
+		/* If that didn't work, look for two windows */
 		link->io.NumPorts1 = link->io.NumPorts2 = 8;
 		info->multi = 2;
-		i = first_tuple(link, tuple, parse);
-		while (i != CS_NO_MORE_ITEMS) {
-			if ((i == CS_SUCCESS) && (cf->io.nwin == 2)) {
-				link->conf.ConfigIndex = cf->index;
-				link->io.BasePort1 = cf->io.win[0].base;
-				link->io.BasePort2 = cf->io.win[1].base;
-				link->io.IOAddrLines =
-				    cf->io.flags & CISTPL_IO_LINES_MASK;
-				i = pcmcia_request_io(link, &link->io);
-				base2 = link->io.BasePort2;
-				if (i == CS_SUCCESS)
-					break;
-			}
-			i = next_tuple(link, tuple, parse);
+		if (pcmcia_loop_config(link, multi_config_check_notpicky,
+				       &base2)) {
+			printk(KERN_NOTICE "serial_cs: no usable port range"
+			       "found, giving up\n");
+			return -ENODEV;
 		}
 	}
 
-	if (i != CS_SUCCESS) {
-		cs_error(link, RequestIO, i);
-		rc = -1;
-		goto free_cfg_mem;
-	}
-
 	i = pcmcia_request_irq(link, &link->irq);
-	if (i != CS_SUCCESS) {
+	if (i != 0) {
+		/* FIXME: comment does not fit, error handling does not fit */
 		printk(KERN_NOTICE
 		       "serial_cs: no usable port range found, giving up\n");
 		cs_error(link, RequestIRQ, i);
@@ -664,10 +624,9 @@ static int multi_config(struct pcmcia_device * link)
 		info->quirk->config(link);
 
 	i = pcmcia_request_configuration(link, &link->conf);
-	if (i != CS_SUCCESS) {
+	if (i != 0) {
 		cs_error(link, RequestConfiguration, i);
-		rc = -1;
-		goto free_cfg_mem;
+		return -ENODEV;
 	}
 
 	/* The Oxford Semiconductor OXCF950 cards are in fact single-port:
@@ -678,7 +637,8 @@ static int multi_config(struct pcmcia_device * link)
 				info->prodid == PRODID_POSSIO_GCC)) {
 		int err;
 
-		if (cf->index == 1 || cf->index == 3) {
+		if (link->conf.ConfigIndex == 1 ||
+		    link->conf.ConfigIndex == 3) {
 			err = setup_serial(link, info, base2,
 					link->irq.AssignedIRQ);
 			base2 = link->io.BasePort1;
@@ -695,18 +655,14 @@ static int multi_config(struct pcmcia_device * link)
 		if (info->quirk && info->quirk->wakeup)
 			info->quirk->wakeup(link);
 
-		rc = 0;
-		goto free_cfg_mem;
+		return 0;
 	}
 
 	setup_serial(link, info, link->io.BasePort1, link->irq.AssignedIRQ);
 	for (i = 0; i < info->multi - 1; i++)
 		setup_serial(link, info, base2 + (8 * i),
 				link->irq.AssignedIRQ);
-	rc = 0;
-free_cfg_mem:
-	kfree(cfg_mem);
-	return rc;
+	return 0;
 }
 
 /*======================================================================
@@ -746,7 +702,7 @@ static int serial_config(struct pcmcia_device * link)
 	/* Is this a compliant multifunction card? */
 	tuple->DesiredTuple = CISTPL_LONGLINK_MFC;
 	tuple->Attributes = TUPLE_RETURN_COMMON | TUPLE_RETURN_LINK;
-	info->multi = (first_tuple(link, tuple, parse) == CS_SUCCESS);
+	info->multi = (first_tuple(link, tuple, parse) == 0);
 
 	/* Is this a multiport card? */
 	tuple->DesiredTuple = CISTPL_MANFID;
@@ -770,7 +726,7 @@ static int serial_config(struct pcmcia_device * link)
 	    ((link->func_id == CISTPL_FUNCID_MULTI) ||
 	     (link->func_id == CISTPL_FUNCID_SERIAL))) {
 		tuple->DesiredTuple = CISTPL_CFTABLE_ENTRY;
-		if (first_tuple(link, tuple, parse) == CS_SUCCESS) {
+		if (first_tuple(link, tuple, parse) == 0) {
 			if ((cf->io.nwin == 1) && (cf->io.win[0].len % 8 == 0))
 				info->multi = cf->io.win[0].len >> 3;
 			if ((cf->io.nwin == 2) && (cf->io.win[0].len == 8) &&
diff --git a/drivers/serial/serial_ks8695.c b/drivers/serial/serial_ks8695.c
index b9cbfc87f616..998e89dc5aaf 100644
--- a/drivers/serial/serial_ks8695.c
+++ b/drivers/serial/serial_ks8695.c
@@ -63,8 +63,44 @@
 #define UART_DUMMY_LSR_RX	0x100
 #define UART_PORT_SIZE		(KS8695_USR - KS8695_URRB + 4)
 
-#define tx_enabled(port) ((port)->unused[0])
-#define rx_enabled(port) ((port)->unused[1])
+static inline int tx_enabled(struct uart_port *port)
+{
+	return port->unused[0] & 1;
+}
+
+static inline int rx_enabled(struct uart_port *port)
+{
+	return port->unused[0] & 2;
+}
+
+static inline int ms_enabled(struct uart_port *port)
+{
+	return port->unused[0] & 4;
+}
+
+static inline void ms_enable(struct uart_port *port, int enabled)
+{
+	if(enabled)
+		port->unused[0] |= 4;
+	else
+		port->unused[0] &= ~4;
+}
+
+static inline void rx_enable(struct uart_port *port, int enabled)
+{
+	if(enabled)
+		port->unused[0] |= 2;
+	else
+		port->unused[0] &= ~2;
+}
+
+static inline void tx_enable(struct uart_port *port, int enabled)
+{
+	if(enabled)
+		port->unused[0] |= 1;
+	else
+		port->unused[0] &= ~1;
+}
 
 
 #ifdef SUPPORT_SYSRQ
@@ -75,7 +111,7 @@ static void ks8695uart_stop_tx(struct uart_port *port)
 {
 	if (tx_enabled(port)) {
 		disable_irq(KS8695_IRQ_UART_TX);
-		tx_enabled(port) = 0;
+		tx_enable(port, 0);
 	}
 }
 
@@ -83,7 +119,7 @@ static void ks8695uart_start_tx(struct uart_port *port)
 {
 	if (!tx_enabled(port)) {
 		enable_irq(KS8695_IRQ_UART_TX);
-		tx_enabled(port) = 1;
+		tx_enable(port, 1);
 	}
 }
 
@@ -91,18 +127,24 @@ static void ks8695uart_stop_rx(struct uart_port *port)
 {
 	if (rx_enabled(port)) {
 		disable_irq(KS8695_IRQ_UART_RX);
-		rx_enabled(port) = 0;
+		rx_enable(port, 0);
 	}
 }
 
 static void ks8695uart_enable_ms(struct uart_port *port)
 {
-	enable_irq(KS8695_IRQ_UART_MODEM_STATUS);
+	if (!ms_enabled(port)) {
+		enable_irq(KS8695_IRQ_UART_MODEM_STATUS);
+		ms_enable(port,1);
+	}
 }
 
 static void ks8695uart_disable_ms(struct uart_port *port)
 {
-	disable_irq(KS8695_IRQ_UART_MODEM_STATUS);
+	if (ms_enabled(port)) {
+		disable_irq(KS8695_IRQ_UART_MODEM_STATUS);
+		ms_enable(port,0);
+	}
 }
 
 static irqreturn_t ks8695uart_rx_chars(int irq, void *dev_id)
@@ -285,8 +327,9 @@ static int ks8695uart_startup(struct uart_port *port)
 	int retval;
 
 	set_irq_flags(KS8695_IRQ_UART_TX, IRQF_VALID | IRQF_NOAUTOEN);
-	tx_enabled(port) = 0;
-	rx_enabled(port) = 1;
+	tx_enable(port, 0);
+	rx_enable(port, 1);
+	ms_enable(port, 1);
 
 	/*
 	 * Allocate the IRQ
diff --git a/drivers/serial/sunhv.c b/drivers/serial/sunhv.c
index e41766d08035..a94a2ab4b571 100644
--- a/drivers/serial/sunhv.c
+++ b/drivers/serial/sunhv.c
@@ -616,7 +616,7 @@ static int __devexit hv_remove(struct of_device *dev)
 	return 0;
 }
 
-static struct of_device_id hv_match[] = {
+static const struct of_device_id hv_match[] = {
 	{
 		.name = "console",
 		.compatible = "qcn",
diff --git a/drivers/serial/sunsab.c b/drivers/serial/sunsab.c
index 29b4458abf74..0355efe115d9 100644
--- a/drivers/serial/sunsab.c
+++ b/drivers/serial/sunsab.c
@@ -1078,7 +1078,7 @@ static int __devexit sab_remove(struct of_device *op)
 	return 0;
 }
 
-static struct of_device_id sab_match[] = {
+static const struct of_device_id sab_match[] = {
 	{
 		.name = "se",
 	},
diff --git a/drivers/serial/sunsu.c b/drivers/serial/sunsu.c
index a378464f9292..a4dc79b1d7ab 100644
--- a/drivers/serial/sunsu.c
+++ b/drivers/serial/sunsu.c
@@ -1506,7 +1506,7 @@ static int __devexit su_remove(struct of_device *op)
 	return 0;
 }
 
-static struct of_device_id su_match[] = {
+static const struct of_device_id su_match[] = {
 	{
 		.name = "su",
 	},
diff --git a/drivers/serial/sunzilog.c b/drivers/serial/sunzilog.c
index 3cb4c8aee13f..45a299f35617 100644
--- a/drivers/serial/sunzilog.c
+++ b/drivers/serial/sunzilog.c
@@ -1480,7 +1480,7 @@ static int __devexit zs_remove(struct of_device *op)
 	return 0;
 }
 
-static struct of_device_id zs_match[] = {
+static const struct of_device_id zs_match[] = {
 	{
 		.name = "zs",
 	},
diff --git a/drivers/serial/ucc_uart.c b/drivers/serial/ucc_uart.c
index 5c5d18dcb6ac..539c933b335f 100644
--- a/drivers/serial/ucc_uart.c
+++ b/drivers/serial/ucc_uart.c
@@ -1009,7 +1009,7 @@ static int qe_uart_request_port(struct uart_port *port)
 	rx_size = L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize);
 	tx_size = L1_CACHE_ALIGN(qe_port->tx_nrfifos * qe_port->tx_fifosize);
 
-	bd_virt = dma_alloc_coherent(NULL, rx_size + tx_size, &bd_dma_addr,
+	bd_virt = dma_alloc_coherent(port->dev, rx_size + tx_size, &bd_dma_addr,
 		GFP_KERNEL);
 	if (!bd_virt) {
 		dev_err(port->dev, "could not allocate buffer descriptors\n");
@@ -1051,7 +1051,7 @@ static void qe_uart_release_port(struct uart_port *port)
 		container_of(port, struct uart_qe_port, port);
 	struct ucc_slow_private *uccs = qe_port->us_private;
 
-	dma_free_coherent(NULL, qe_port->bd_size, qe_port->bd_virt,
+	dma_free_coherent(port->dev, qe_port->bd_size, qe_port->bd_virt,
 			  qe_port->bd_dma_addr);
 
 	ucc_slow_free(uccs);