spi: Don't break user-visible strings to multiple source lines in drivers

User-visible strings are more difficult to grep from sources if they are
separated to multiple source lines. This is worse than over 80 columns long
line code style violation.

Fix this by making those to single-line strings or by breaking them between
variables.

While at there, convert if (printk_ratelimit()) dev_warn() to use
dev_warn_ratelimited in spi-pxa2xx.c.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

1 files changed, 16 insertions, 20 deletions

diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c
index c1a50674c1e3..64e1682c39b1 100644
--- a/drivers/spi/spi-pxa2xx.c
+++ b/drivers/spi/spi-pxa2xx.c
@@ -573,8 +573,8 @@ static irqreturn_t ssp_int(int irq, void *dev_id)
 			write_SSTO(0, reg);
 		write_SSSR_CS(drv_data, drv_data->clear_sr);
 
-		dev_err(&drv_data->pdev->dev, "bad message state "
-			"in interrupt handler\n");
+		dev_err(&drv_data->pdev->dev,
+			"bad message state in interrupt handler\n");
 
 		/* Never fail */
 		return IRQ_HANDLED;
@@ -651,8 +651,8 @@ static void pump_transfers(unsigned long data)
 		if (message->is_dma_mapped
 				|| transfer->rx_dma || transfer->tx_dma) {
 			dev_err(&drv_data->pdev->dev,
-				"pump_transfers: mapped transfer length "
-				"of %u is greater than %d\n",
+				"pump_transfers: mapped transfer length of "
+				"%u is greater than %d\n",
 				transfer->len, MAX_DMA_LEN);
 			message->status = -EINVAL;
 			giveback(drv_data);
@@ -660,11 +660,10 @@ static void pump_transfers(unsigned long data)
 		}
 
 		/* warn ... we force this to PIO mode */
-		if (printk_ratelimit())
-			dev_warn(&message->spi->dev, "pump_transfers: "
-				"DMA disabled for transfer length %ld "
-				"greater than %d\n",
-				(long)drv_data->len, MAX_DMA_LEN);
+		dev_warn_ratelimited(&message->spi->dev,
+				     "pump_transfers: DMA disabled for transfer length %ld "
+				     "greater than %d\n",
+				     (long)drv_data->len, MAX_DMA_LEN);
 	}
 
 	/* Setup the transfer state based on the type of transfer */
@@ -726,11 +725,8 @@ static void pump_transfers(unsigned long data)
 							message->spi,
 							bits, &dma_burst,
 							&dma_thresh))
-				if (printk_ratelimit())
-					dev_warn(&message->spi->dev,
-						"pump_transfers: "
-						"DMA burst size reduced to "
-						"match bits_per_word\n");
+				dev_warn_ratelimited(&message->spi->dev,
+						     "pump_transfers: DMA burst size reduced to match bits_per_word\n");
 		}
 
 		cr0 = clk_div
@@ -854,8 +850,8 @@ static int setup_cs(struct spi_device *spi, struct chip_data *chip,
 	if (gpio_is_valid(chip_info->gpio_cs)) {
 		err = gpio_request(chip_info->gpio_cs, "SPI_CS");
 		if (err) {
-			dev_err(&spi->dev, "failed to request chip select "
-					"GPIO%d\n", chip_info->gpio_cs);
+			dev_err(&spi->dev, "failed to request chip select GPIO%d\n",
+				chip_info->gpio_cs);
 			return err;
 		}
 
@@ -899,8 +895,8 @@ static int setup(struct spi_device *spi)
 
 		if (drv_data->ssp_type == CE4100_SSP) {
 			if (spi->chip_select > 4) {
-				dev_err(&spi->dev, "failed setup: "
-				"cs number must not be > 4.\n");
+				dev_err(&spi->dev,
+					"failed setup: cs number must not be > 4.\n");
 				kfree(chip);
 				return -EINVAL;
 			}
@@ -956,8 +952,8 @@ static int setup(struct spi_device *spi)
 						spi->bits_per_word,
 						&chip->dma_burst_size,
 						&chip->dma_threshold)) {
-			dev_warn(&spi->dev, "in setup: DMA burst size reduced "
-					"to match bits_per_word\n");
+			dev_warn(&spi->dev,
+				 "in setup: DMA burst size reduced to match bits_per_word\n");
 		}
 	}