USB: Allow USB 3.0 ports to be disabled.

If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port.  Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects.  To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.

The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes.  We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect.  However,
external USB 3.0 hubs don't need this code.  They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set.  Therefore it doesn't make sense to
put this code in the USB core.

This patch is part of a series to fix several reports of infinite loops
on device enumeration failure.  This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller.  The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.

This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore: refine warm
reset logic"

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org

1 files changed, 29 insertions, 2 deletions

diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index a686cf4905bb..a7dd4f311e14 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -761,12 +761,39 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 			break;
 		case USB_PORT_FEAT_LINK_STATE:
 			temp = xhci_readl(xhci, port_array[wIndex]);
+
+			/* Disable port */
+			if (link_state == USB_SS_PORT_LS_SS_DISABLED) {
+				xhci_dbg(xhci, "Disable port %d\n", wIndex);
+				temp = xhci_port_state_to_neutral(temp);
+				/*
+				 * Clear all change bits, so that we get a new
+				 * connection event.
+				 */
+				temp |= PORT_CSC | PORT_PEC | PORT_WRC |
+					PORT_OCC | PORT_RC | PORT_PLC |
+					PORT_CEC;
+				xhci_writel(xhci, temp | PORT_PE,
+					port_array[wIndex]);
+				temp = xhci_readl(xhci, port_array[wIndex]);
+				break;
+			}
+
+			/* Put link in RxDetect (enable port) */
+			if (link_state == USB_SS_PORT_LS_RX_DETECT) {
+				xhci_dbg(xhci, "Enable port %d\n", wIndex);
+				xhci_set_link_state(xhci, port_array, wIndex,
+						link_state);
+				temp = xhci_readl(xhci, port_array[wIndex]);
+				break;
+			}
+
 			/* Software should not attempt to set
-			 * port link state above '5' (Rx.Detect) and the port
+			 * port link state above '3' (U3) and the port
 			 * must be enabled.
 			 */
 			if ((temp & PORT_PE) == 0 ||
-				(link_state > USB_SS_PORT_LS_RX_DETECT)) {
+				(link_state > USB_SS_PORT_LS_U3)) {
 				xhci_warn(xhci, "Cannot set link state.\n");
 				goto error;
 			}