xhci: Implement HS/FS/LS bandwidth checking.

Now that we have a bandwidth interval table per root port or TT that
describes the endpoint bandwidth information, we can finally use it to
check whether the bus bandwidth is oversubscribed for a new device
configuration/alternate interface setting.

The complication for this algorithm is that the bit of hardware logic that
creates the bus schedule is only 12-bit logic.  In order to make sure it
can represent the maximum bus bandwidth in 12 bits, it has to convert the
endpoint max packet size and max esit payload into "blocks" (basically a
less-precise representation).  The block size for each speed of device is
different, aside from low speed and full speed.  In order to make sure we
don't allow a setup where the scheduler might fail, we also have to do the
bandwidth checking in blocks.

After checking that the endpoints fit in the schedule, we store the
bandwidth used for this root port or TT.  If this is a FS/LS device under
an external HS hub, we also update the TT bandwidth and the root port
bandwidth (if this is a newly activated or deactivated TT).

I won't go into the details of the algorithm, as it's pretty well
documented in the comments.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 46 insertions, 0 deletions

diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 050f07b1e790..b224b20b0784 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -756,6 +756,49 @@ struct xhci_bw_info {
 	unsigned int		type;
 };
 
+/* "Block" sizes in bytes the hardware uses for different device speeds.
+ * The logic in this part of the hardware limits the number of bits the hardware
+ * can use, so must represent bandwidth in a less precise manner to mimic what
+ * the scheduler hardware computes.
+ */
+#define	FS_BLOCK	1
+#define	HS_BLOCK	4
+#define	SS_BLOCK	16
+#define	DMI_BLOCK	32
+
+/* Each device speed has a protocol overhead (CRC, bit stuffing, etc) associated
+ * with each byte transferred.  SuperSpeed devices have an initial overhead to
+ * set up bursts.  These are in blocks, see above.  LS overhead has already been
+ * translated into FS blocks.
+ */
+#define DMI_OVERHEAD 8
+#define DMI_OVERHEAD_BURST 4
+#define SS_OVERHEAD 8
+#define SS_OVERHEAD_BURST 32
+#define HS_OVERHEAD 26
+#define FS_OVERHEAD 20
+#define LS_OVERHEAD 128
+/* The TTs need to claim roughly twice as much bandwidth (94 bytes per
+ * microframe ~= 24Mbps) of the HS bus as the devices can actually use because
+ * of overhead associated with split transfers crossing microframe boundaries.
+ * 31 blocks is pure protocol overhead.
+ */
+#define TT_HS_OVERHEAD (31 + 94)
+#define TT_DMI_OVERHEAD (25 + 12)
+
+/* Bandwidth limits in blocks */
+#define FS_BW_LIMIT		1285
+#define TT_BW_LIMIT		1320
+#define HS_BW_LIMIT		1607
+#define SS_BW_LIMIT_IN		3906
+#define DMI_BW_LIMIT_IN		3906
+#define SS_BW_LIMIT_OUT		3906
+#define DMI_BW_LIMIT_OUT	3906
+
+/* Percentage of bus bandwidth reserved for non-periodic transfers */
+#define FS_BW_RESERVED		10
+#define HS_BW_RESERVED		20
+
 struct xhci_virt_ep {
 	struct xhci_ring		*ring;
 	/* Related to endpoints that are configured to use stream IDs only */
@@ -823,6 +866,8 @@ struct xhci_interval_bw {
 struct xhci_interval_bw_table {
 	unsigned int		interval0_esit_payload;
 	struct xhci_interval_bw	interval_bw[XHCI_MAX_INTERVAL];
+	/* Includes reserved bandwidth for async endpoints */
+	unsigned int		bw_used;
 };
 
 
@@ -1397,6 +1442,7 @@ struct xhci_hcd {
 #define XHCI_EP_LIMIT_QUIRK	(1 << 5)
 #define XHCI_BROKEN_MSI		(1 << 6)
 #define XHCI_RESET_ON_RESUME	(1 << 7)
+#define	XHCI_SW_BW_CHECKING	(1 << 8)
 	unsigned int		num_active_eps;
 	unsigned int		limit_active_eps;
 	/* There are two roothubs to keep track of bus suspend info for */