usb: musb: drop a gigantic amount of ifdeferry

the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.

This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 1 insertions, 74 deletions

diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig
index 13093481f918..6192b45959f4 100644
--- a/drivers/usb/musb/Kconfig
+++ b/drivers/usb/musb/Kconfig
@@ -8,7 +8,7 @@ comment "Enable Host or Gadget support to see Inventra options"
 
 # (M)HDRC = (Multipoint) Highspeed Dual-Role Controller
 config USB_MUSB_HDRC
-	depends on (USB || USB_GADGET)
+	depends on USB && USB_GADGET
 	depends on (ARM || (BF54x && !BF544) || (BF52x && !BF522 && !BF523))
 	select NOP_USB_XCEIV if (ARCH_DAVINCI || MACH_OMAP3EVM || BLACKFIN)
 	select TWL4030_USB if MACH_OMAP_3430SDP
@@ -67,79 +67,6 @@ config USB_MUSB_UX500
 
 endchoice
 
-choice
-	prompt "Driver Mode"
-	depends on USB_MUSB_HDRC
-	help
-	  Dual-Role devices can support both host and peripheral roles,
-	  as well as a the special "OTG Device" role which can switch
-	  between both roles as needed.
-
-# use USB_MUSB_HDRC_HCD not USB_MUSB_HOST to #ifdef host side support;
-# OTG needs both roles, not just USB_MUSB_HOST.
-config USB_MUSB_HOST
-	depends on USB
-	bool "USB Host"
-	help
-	  Say Y here if your system supports the USB host role.
-	  If it has a USB "A" (rectangular), "Mini-A" (uncommon),
-	  or "Mini-AB" connector, it supports the host role.
-	  (With a "Mini-AB" connector, you should enable USB OTG.)
-
-# use USB_GADGET_MUSB_HDRC not USB_MUSB_PERIPHERAL to #ifdef peripheral
-# side support ... OTG needs both roles
-config USB_MUSB_PERIPHERAL
-	depends on USB_GADGET
-	bool "USB Peripheral (gadget stack)"
-	select USB_GADGET_MUSB_HDRC
-	help
-	  Say Y here if your system supports the USB peripheral role.
-	  If it has a USB "B" (squarish), "Mini-B", or "Mini-AB"
-	  connector, it supports the peripheral role.
-	  (With a "Mini-AB" connector, you should enable USB OTG.)
-
-config USB_MUSB_OTG
-	depends on USB && USB_GADGET && PM && EXPERIMENTAL
-	bool "Both host and peripheral:  USB OTG (On The Go) Device"
-	select USB_GADGET_MUSB_HDRC
-	select USB_OTG
-	help
-	   The most notable feature of USB OTG is support for a
-	   "Dual-Role" device, which can act as either a device
-	   or a host.  The initial role choice can be changed
-	   later, when two dual-role devices talk to each other.
-
-	   At this writing, the OTG support in this driver is incomplete,
-	   omitting the mandatory HNP or SRP protocols.  However, some
-	   of the cable based role switching works.  (That is, grounding
-	   the ID pin switches the controller to host mode, while leaving
-	   it floating leaves it in peripheral mode.)
-
-	   Select this if your system has a Mini-AB connector, or
-	   to simplify certain kinds of configuration.
-
-	   To implement your OTG Targeted Peripherals List (TPL), enable
-	   USB_OTG_WHITELIST and update "drivers/usb/core/otg_whitelist.h"
-	   to match your requirements.
-
-endchoice
-
-# enable peripheral support (including with OTG)
-config USB_GADGET_MUSB_HDRC
-	bool
-	depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG)
-#	default y
-#	select USB_GADGET_DUALSPEED
-#	select USB_GADGET_SELECTED
-
-# enables host support (including with OTG)
-config USB_MUSB_HDRC_HCD
-	bool
-	depends on USB_MUSB_HDRC && (USB_MUSB_HOST || USB_MUSB_OTG)
-	select USB_OTG if USB_GADGET_MUSB_HDRC
-	default y
-
-
 config MUSB_PIO_ONLY
 	bool 'Disable DMA (always use PIO)'
 	depends on USB_MUSB_HDRC