usb: musb: drop a gigantic amount of ifdeferry

the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.

This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 3 insertions, 23 deletions

diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c
index b410357cf016..9eec41fbf3a4 100644
--- a/drivers/usb/musb/tusb6010.c
+++ b/drivers/usb/musb/tusb6010.c
@@ -269,8 +269,6 @@ void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *buf)
 
 static struct musb *the_musb;
 
-#ifdef CONFIG_USB_GADGET_MUSB_HDRC
-
 /* This is used by gadget drivers, and OTG transceiver logic, allowing
  * at most mA current to be drawn from VBUS during a Default-B session
  * (that is, while VBUS exceeds 4.4V).  In Default-A (including pure host
@@ -310,10 +308,6 @@ static int tusb_draw_power(struct otg_transceiver *x, unsigned mA)
 	return 0;
 }
 
-#else
-#define tusb_draw_power	NULL
-#endif
-
 /* workaround for issue 13:  change clock during chip idle
  * (to be fixed in rev3 silicon) ... symptoms include disconnect
  * or looping suspend/resume cycles
@@ -440,19 +434,15 @@ static void musb_do_idle(unsigned long _musb)
 		if (is_host_active(musb) && (musb->port1_status >> 16))
 			goto done;
 
-#ifdef CONFIG_USB_GADGET_MUSB_HDRC
-		if (is_peripheral_enabled(musb) && !musb->gadget_driver)
+		if (is_peripheral_enabled(musb) && !musb->gadget_driver) {
 			wakeups = 0;
-		else {
+		} else {
 			wakeups = TUSB_PRCM_WHOSTDISCON
-					| TUSB_PRCM_WBUS
+				| TUSB_PRCM_WBUS
 					| TUSB_PRCM_WVBUS;
 			if (is_otg_enabled(musb))
 				wakeups |= TUSB_PRCM_WID;
 		}
-#else
-		wakeups = TUSB_PRCM_WHOSTDISCON | TUSB_PRCM_WBUS;
-#endif
 		tusb_allow_idle(musb, wakeups);
 	}
 done:
@@ -610,30 +600,22 @@ static int tusb_musb_set_mode(struct musb *musb, u8 musb_mode)
 
 	switch (musb_mode) {
 
-#ifdef CONFIG_USB_MUSB_HDRC_HCD
 	case MUSB_HOST:		/* Disable PHY ID detect, ground ID */
 		phy_otg_ctrl &= ~TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
 		phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
 		dev_conf |= TUSB_DEV_CONF_ID_SEL;
 		dev_conf &= ~TUSB_DEV_CONF_SOFT_ID;
 		break;
-#endif
-
-#ifdef CONFIG_USB_GADGET_MUSB_HDRC
 	case MUSB_PERIPHERAL:	/* Disable PHY ID detect, keep ID pull-up on */
 		phy_otg_ctrl |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
 		phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
 		dev_conf |= (TUSB_DEV_CONF_ID_SEL | TUSB_DEV_CONF_SOFT_ID);
 		break;
-#endif
-
-#ifdef CONFIG_USB_MUSB_OTG
 	case MUSB_OTG:		/* Use PHY ID detection */
 		phy_otg_ctrl |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
 		phy_otg_ena |= TUSB_PHY_OTG_CTRL_OTG_ID_PULLUP;
 		dev_conf &= ~(TUSB_DEV_CONF_ID_SEL | TUSB_DEV_CONF_SOFT_ID);
 		break;
-#endif
 
 	default:
 		dev_dbg(musb->controller, "Trying to set mode %i\n", musb_mode);
@@ -684,7 +666,6 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase)
 		/* B-dev state machine:  no vbus ~= disconnect */
 		if ((is_otg_enabled(musb) && !musb->xceiv->default_a)
 				|| !is_host_enabled(musb)) {
-#ifdef CONFIG_USB_MUSB_HDRC_HCD
 			/* ? musb_root_disconnect(musb); */
 			musb->port1_status &=
 				~(USB_PORT_STAT_CONNECTION
@@ -693,7 +674,6 @@ tusb_otg_ints(struct musb *musb, u32 int_src, void __iomem *tbase)
 				| USB_PORT_STAT_HIGH_SPEED
 				| USB_PORT_STAT_TEST
 				);
-#endif
 
 			if (otg_stat & TUSB_DEV_OTG_STAT_SESS_END) {
 				dev_dbg(musb->controller, "Forcing disconnect (no interrupt)\n");