diff options
| author | Ji-Ze Hong (Peter Hong) <hpeter@gmail.com> | 2018-11-15 03:58:44 +0100 |
|---|---|---|
| committer | Johan Hovold <johan@kernel.org> | 2018-11-20 18:25:44 +0100 |
| commit | ab60075f2a4eebca1abb04f712569963fb4d9d6c (patch) | |
| tree | cbff83174d3b2ce8641de576675be9dccf38a687 /drivers | |
| parent | USB: serial: mos7840: remove set but not used variables 'st, data1, iflag' (diff) | |
| download | linux-ab60075f2a4eebca1abb04f712569963fb4d9d6c.tar.xz linux-ab60075f2a4eebca1abb04f712569963fb4d9d6c.zip | |
USB: serial: f81534: fix reading old/new IC config
The F81532/534 had a internal configuration space to save & control
IC state with address F81534_CUSTOM_ADDRESS_START (0x2f00). Layout
as following:
+00h: to indicate the section is valid
+01h~04h: UART Mode & port availability
+05h~08h: Output pin control on IC power on
+09h~12h: Output pin control on working <-- New added
Old driver will use +05~08h as default on working, but newer IC will
configed with shutdown mode(7) in 05h~08h and working mode with RS232(1)
in 09h~12h. It'll make mainstream driver not working.
This patch will make mainstream driver compatible older and newer IC.
If using a old IC, the +05h~08h will be 00h~06h, we'll direct apply it.
If using a new IC, the +05h~08h will be 07h or larger, we'll read +09h~12h
to apply newer configuration.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/usb/serial/f81534.c | 20 |
1 files changed, 17 insertions, 3 deletions
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c index 380933db34dd..2b39bda035c7 100644 --- a/drivers/usb/serial/f81534.c +++ b/drivers/usb/serial/f81534.c @@ -45,14 +45,17 @@ #define F81534_CONFIG1_REG (0x09 + F81534_UART_BASE_ADDRESS) #define F81534_DEF_CONF_ADDRESS_START 0x3000 -#define F81534_DEF_CONF_SIZE 8 +#define F81534_DEF_CONF_SIZE 12 #define F81534_CUSTOM_ADDRESS_START 0x2f00 #define F81534_CUSTOM_DATA_SIZE 0x10 #define F81534_CUSTOM_NO_CUSTOM_DATA 0xff #define F81534_CUSTOM_VALID_TOKEN 0xf0 #define F81534_CONF_OFFSET 1 -#define F81534_CONF_GPIO_OFFSET 4 +#define F81534_CONF_INIT_GPIO_OFFSET 4 +#define F81534_CONF_WORK_GPIO_OFFSET 8 +#define F81534_CONF_GPIO_SHUTDOWN 7 +#define F81534_CONF_GPIO_RS232 1 #define F81534_MAX_DATA_BLOCK 64 #define F81534_MAX_BUS_RETRY 20 @@ -1337,8 +1340,19 @@ static int f81534_set_port_output_pin(struct usb_serial_port *port) serial_priv = usb_get_serial_data(serial); port_priv = usb_get_serial_port_data(port); - idx = F81534_CONF_GPIO_OFFSET + port_priv->phy_num; + idx = F81534_CONF_INIT_GPIO_OFFSET + port_priv->phy_num; value = serial_priv->conf_data[idx]; + if (value >= F81534_CONF_GPIO_SHUTDOWN) { + /* + * Newer IC configure will make transceiver in shutdown mode on + * initial power on. We need enable it before using UARTs. + */ + idx = F81534_CONF_WORK_GPIO_OFFSET + port_priv->phy_num; + value = serial_priv->conf_data[idx]; + if (value >= F81534_CONF_GPIO_SHUTDOWN) + value = F81534_CONF_GPIO_RS232; + } + pins = &f81534_port_out_pins[port_priv->phy_num]; for (i = 0; i < ARRAY_SIZE(pins->pin); ++i) { |