net: marvell: Fix the trailing format of some block comments

Use a trailing */ on a separate line for block comments.

Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

3 files changed, 14 insertions, 7 deletions

diff --git a/drivers/net/ethernet/marvell/mv643xx_eth.c b/drivers/net/ethernet/marvell/mv643xx_eth.c
index 3bfb659b5c99..ca1681aa951a 100644
--- a/drivers/net/ethernet/marvell/mv643xx_eth.c
+++ b/drivers/net/ethernet/marvell/mv643xx_eth.c
@@ -700,7 +700,8 @@ static int skb_tx_csum(struct mv643xx_eth_private *mp, struct sk_buff *skb,
 			   ip_hdr(skb)->ihl << TX_IHL_SHIFT;
 
 		/* TODO: Revisit this. With the usage of GEN_TCP_UDP_CHK_FULL
-		 * it seems we don't need to pass the initial checksum. */
+		 * it seems we don't need to pass the initial checksum.
+		 */
 		switch (ip_hdr(skb)->protocol) {
 		case IPPROTO_UDP:
 			cmd |= UDP_FRAME;
@@ -790,7 +791,8 @@ txq_put_hdr_tso(struct sk_buff *skb, struct tx_queue *txq, int length,
 		WARN(1, "failed to prepare checksum!");
 
 	/* Should we set this? Can't use the value from skb_tx_csum()
-	 * as it's not the correct initial L4 checksum to use. */
+	 * as it's not the correct initial L4 checksum to use.
+	 */
 	desc->l4i_chk = 0;
 
 	desc->byte_cnt = hdr_len;
diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index d7104c29d625..d514ec68e47b 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -3993,7 +3993,8 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
 
 	/* Armada 370 documentation says we can only change the port mode
 	 * and in-band enable when the link is down, so force it down
-	 * while making these changes. We also do this for GMAC_CTRL2 */
+	 * while making these changes. We also do this for GMAC_CTRL2
+	 */
 	if ((new_ctrl0 ^ gmac_ctrl0) & MVNETA_GMAC0_PORT_1000BASE_X ||
 	    (new_ctrl2 ^ gmac_ctrl2) & MVNETA_GMAC2_INBAND_AN_ENABLE ||
 	    (new_an  ^ gmac_an) & MVNETA_GMAC_INBAND_AN_ENABLE) {
@@ -4905,7 +4906,8 @@ static int mvneta_ethtool_set_eee(struct net_device *dev,
 	u32 lpi_ctl0;
 
 	/* The Armada 37x documents do not give limits for this other than
-	 * it being an 8-bit register. */
+	 * it being an 8-bit register.
+	 */
 	if (eee->tx_lpi_enabled && eee->tx_lpi_timer > 255)
 		return -EINVAL;
 
diff --git a/drivers/net/ethernet/marvell/sky2.c b/drivers/net/ethernet/marvell/sky2.c
index 2a752fb6b758..68c154d715d6 100644
--- a/drivers/net/ethernet/marvell/sky2.c
+++ b/drivers/net/ethernet/marvell/sky2.c
@@ -55,7 +55,8 @@
 #define RX_DEF_PENDING		RX_MAX_PENDING
 
 /* This is the worst case number of transmit list elements for a single skb:
-   VLAN:GSO + CKSUM + Data + skb_frags * DMA */
+ * VLAN:GSO + CKSUM + Data + skb_frags * DMA
+ */
 #define MAX_SKB_TX_LE	(2 + (sizeof(dma_addr_t)/sizeof(u32))*(MAX_SKB_FRAGS+1))
 #define TX_MIN_PENDING		(MAX_SKB_TX_LE+1)
 #define TX_MAX_PENDING		1024
@@ -1529,7 +1530,8 @@ static void sky2_rx_start(struct sky2_port *sky2)
 		sky2_write32(hw, Q_ADDR(rxq, Q_WM), BMU_WM_PEX);
 
 	/* These chips have no ram buffer?
-	 * MAC Rx RAM Read is controlled by hardware */
+	 * MAC Rx RAM Read is controlled by hardware
+	 */
 	if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
 	    hw->chip_rev > CHIP_REV_YU_EC_U_A0)
 		sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS);
@@ -4684,7 +4686,8 @@ static __exit void sky2_debug_cleanup(void)
 #endif
 
 /* Two copies of network device operations to handle special case of
-   not allowing netpoll on second port */
+ * not allowing netpoll on second port
+ */
 static const struct net_device_ops sky2_netdev_ops[2] = {
   {
 	.ndo_open		= sky2_open,