parisc: move include/asm-parisc to arch/parisc/include/asm

1 files changed, 0 insertions, 294 deletions

diff --git a/include/asm-parisc/pci.h b/include/asm-parisc/pci.h
deleted file mode 100644
index 4ba868f44a5e..000000000000
--- a/include/asm-parisc/pci.h
+++ /dev/null
@@ -1,294 +0,0 @@
-#ifndef __ASM_PARISC_PCI_H
-#define __ASM_PARISC_PCI_H
-
-#include <asm/scatterlist.h>
-
-
-
-/*
-** HP PCI platforms generally support multiple bus adapters.
-**    (workstations 1-~4, servers 2-~32)
-**
-** Newer platforms number the busses across PCI bus adapters *sparsely*.
-** E.g. 0, 8, 16, ...
-**
-** Under a PCI bus, most HP platforms support PPBs up to two or three
-** levels deep. See "Bit3" product line. 
-*/
-#define PCI_MAX_BUSSES	256
-
-
-/* To be used as: mdelay(pci_post_reset_delay);
- *
- * post_reset is the time the kernel should stall to prevent anyone from
- * accessing the PCI bus once #RESET is de-asserted. 
- * PCI spec somewhere says 1 second but with multi-PCI bus systems,
- * this makes the boot time much longer than necessary.
- * 20ms seems to work for all the HP PCI implementations to date.
- */
-#define pci_post_reset_delay 50
-
-
-/*
-** pci_hba_data (aka H2P_OBJECT in HP/UX)
-**
-** This is the "common" or "base" data structure which HBA drivers
-** (eg Dino or LBA) are required to place at the top of their own
-** platform_data structure.  I've heard this called "C inheritance" too.
-**
-** Data needed by pcibios layer belongs here.
-*/
-struct pci_hba_data {
-	void __iomem   *base_addr;	/* aka Host Physical Address */
-	const struct parisc_device *dev; /* device from PA bus walk */
-	struct pci_bus *hba_bus;	/* primary PCI bus below HBA */
-	int		hba_num;	/* I/O port space access "key" */
-	struct resource bus_num;	/* PCI bus numbers */
-	struct resource io_space;	/* PIOP */
-	struct resource lmmio_space;	/* bus addresses < 4Gb */
-	struct resource elmmio_space;	/* additional bus addresses < 4Gb */
-	struct resource gmmio_space;	/* bus addresses > 4Gb */
-
-	/* NOTE: Dino code assumes it can use *all* of the lmmio_space,
-	 * elmmio_space and gmmio_space as a contiguous array of
-	 * resources.  This #define represents the array size */
-	#define DINO_MAX_LMMIO_RESOURCES	3
-
-	unsigned long   lmmio_space_offset;  /* CPU view - PCI view */
-	void *          iommu;          /* IOMMU this device is under */
-	/* REVISIT - spinlock to protect resources? */
-
-	#define HBA_NAME_SIZE 16
-	char io_name[HBA_NAME_SIZE];
-	char lmmio_name[HBA_NAME_SIZE];
-	char elmmio_name[HBA_NAME_SIZE];
-	char gmmio_name[HBA_NAME_SIZE];
-};
-
-#define HBA_DATA(d)		((struct pci_hba_data *) (d))
-
-/* 
-** We support 2^16 I/O ports per HBA.  These are set up in the form
-** 0xbbxxxx, where bb is the bus number and xxxx is the I/O port
-** space address.
-*/
-#define HBA_PORT_SPACE_BITS	16
-
-#define HBA_PORT_BASE(h)	((h) << HBA_PORT_SPACE_BITS)
-#define HBA_PORT_SPACE_SIZE	(1UL << HBA_PORT_SPACE_BITS)
-
-#define PCI_PORT_HBA(a)		((a) >> HBA_PORT_SPACE_BITS)
-#define PCI_PORT_ADDR(a)	((a) & (HBA_PORT_SPACE_SIZE - 1))
-
-#ifdef CONFIG_64BIT
-#define PCI_F_EXTEND		0xffffffff00000000UL
-#define PCI_IS_LMMIO(hba,a)	pci_is_lmmio(hba,a)
-
-/* We need to know if an address is LMMMIO or GMMIO.
- * LMMIO requires mangling and GMMIO we must use as-is.
- */
-static __inline__  int pci_is_lmmio(struct pci_hba_data *hba, unsigned long a)
-{
-	return(((a) & PCI_F_EXTEND) == PCI_F_EXTEND);
-}
-
-/*
-** Convert between PCI (IO_VIEW) addresses and processor (PA_VIEW) addresses.
-** See pci.c for more conversions used by Generic PCI code.
-**
-** Platform characteristics/firmware guarantee that
-**	(1) PA_VIEW - IO_VIEW = lmmio_offset for both LMMIO and ELMMIO
-**	(2) PA_VIEW == IO_VIEW for GMMIO
-*/
-#define PCI_BUS_ADDR(hba,a)	(PCI_IS_LMMIO(hba,a)	\
-		?  ((a) - hba->lmmio_space_offset)	/* mangle LMMIO */ \
-		: (a))					/* GMMIO */
-#define PCI_HOST_ADDR(hba,a)	(((a) & PCI_F_EXTEND) == 0 \
-		? (a) + hba->lmmio_space_offset \
-		: (a))
-
-#else	/* !CONFIG_64BIT */
-
-#define PCI_BUS_ADDR(hba,a)	(a)
-#define PCI_HOST_ADDR(hba,a)	(a)
-#define PCI_F_EXTEND		0UL
-#define PCI_IS_LMMIO(hba,a)	(1)	/* 32-bit doesn't support GMMIO */
-
-#endif /* !CONFIG_64BIT */
-
-/*
-** KLUGE: linux/pci.h include asm/pci.h BEFORE declaring struct pci_bus
-** (This eliminates some of the warnings).
-*/
-struct pci_bus;
-struct pci_dev;
-
-/*
- * If the PCI device's view of memory is the same as the CPU's view of memory,
- * PCI_DMA_BUS_IS_PHYS is true.  The networking and block device layers use
- * this boolean for bounce buffer decisions.
- */
-#ifdef CONFIG_PA20
-/* All PA-2.0 machines have an IOMMU. */
-#define PCI_DMA_BUS_IS_PHYS	0
-#define parisc_has_iommu()	do { } while (0)
-#else
-
-#if defined(CONFIG_IOMMU_CCIO) || defined(CONFIG_IOMMU_SBA)
-extern int parisc_bus_is_phys; 	/* in arch/parisc/kernel/setup.c */
-#define PCI_DMA_BUS_IS_PHYS	parisc_bus_is_phys
-#define parisc_has_iommu()	do { parisc_bus_is_phys = 0; } while (0)
-#else
-#define PCI_DMA_BUS_IS_PHYS	1
-#define parisc_has_iommu()	do { } while (0)
-#endif
-
-#endif	/* !CONFIG_PA20 */
-
-
-/*
-** Most PCI devices (eg Tulip, NCR720) also export the same registers
-** to both MMIO and I/O port space.  Due to poor performance of I/O Port
-** access under HP PCI bus adapters, strongly recommend the use of MMIO
-** address space.
-**
-** While I'm at it more PA programming notes:
-**
-** 1) MMIO stores (writes) are posted operations. This means the processor
-**    gets an "ACK" before the write actually gets to the device. A read
-**    to the same device (or typically the bus adapter above it) will
-**    force in-flight write transaction(s) out to the targeted device
-**    before the read can complete.
-**
-** 2) The Programmed I/O (PIO) data may not always be strongly ordered with
-**    respect to DMA on all platforms. Ie PIO data can reach the processor
-**    before in-flight DMA reaches memory. Since most SMP PA platforms
-**    are I/O coherent, it generally doesn't matter...but sometimes
-**    it does.
-**
-** I've helped device driver writers debug both types of problems.
-*/
-struct pci_port_ops {
-	  u8 (*inb)  (struct pci_hba_data *hba, u16 port);
-	 u16 (*inw)  (struct pci_hba_data *hba, u16 port);
-	 u32 (*inl)  (struct pci_hba_data *hba, u16 port);
-	void (*outb) (struct pci_hba_data *hba, u16 port,  u8 data);
-	void (*outw) (struct pci_hba_data *hba, u16 port, u16 data);
-	void (*outl) (struct pci_hba_data *hba, u16 port, u32 data);
-};
-
-
-struct pci_bios_ops {
-	void (*init)(void);
-	void (*fixup_bus)(struct pci_bus *bus);
-};
-
-/* pci_unmap_{single,page} is not a nop, thus... */
-#define DECLARE_PCI_UNMAP_ADDR(ADDR_NAME)	\
-	dma_addr_t ADDR_NAME;
-#define DECLARE_PCI_UNMAP_LEN(LEN_NAME)		\
-	__u32 LEN_NAME;
-#define pci_unmap_addr(PTR, ADDR_NAME)			\
-	((PTR)->ADDR_NAME)
-#define pci_unmap_addr_set(PTR, ADDR_NAME, VAL)		\
-	(((PTR)->ADDR_NAME) = (VAL))
-#define pci_unmap_len(PTR, LEN_NAME)			\
-	((PTR)->LEN_NAME)
-#define pci_unmap_len_set(PTR, LEN_NAME, VAL)		\
-	(((PTR)->LEN_NAME) = (VAL))
-
-/*
-** Stuff declared in arch/parisc/kernel/pci.c
-*/
-extern struct pci_port_ops *pci_port;
-extern struct pci_bios_ops *pci_bios;
-
-#ifdef CONFIG_PCI
-extern void pcibios_register_hba(struct pci_hba_data *);
-extern void pcibios_set_master(struct pci_dev *);
-#else
-static inline void pcibios_register_hba(struct pci_hba_data *x)
-{
-}
-#endif
-
-/*
- * pcibios_assign_all_busses() is used in drivers/pci/pci.c:pci_do_scan_bus()
- *   0 == check if bridge is numbered before re-numbering.
- *   1 == pci_do_scan_bus() should automatically number all PCI-PCI bridges.
- *
- *   We *should* set this to zero for "legacy" platforms and one
- *   for PAT platforms.
- *
- *   But legacy platforms also need to renumber the busses below a Host
- *   Bus controller.  Adding a 4-port Tulip card on the first PCI root
- *   bus of a C200 resulted in the secondary bus being numbered as 1.
- *   The second PCI host bus controller's root bus had already been
- *   assigned bus number 1 by firmware and sysfs complained.
- *
- *   Firmware isn't doing anything wrong here since each controller
- *   is its own PCI domain.  It's simpler and easier for us to renumber
- *   the busses rather than treat each Dino as a separate PCI domain.
- *   Eventually, we may want to introduce PCI domains for Superdome or
- *   rp7420/8420 boxes and then revisit this issue.
- */
-#define pcibios_assign_all_busses()     (1)
-#define pcibios_scan_all_fns(a, b)	(0)
-
-#define PCIBIOS_MIN_IO          0x10
-#define PCIBIOS_MIN_MEM         0x1000 /* NBPG - but pci/setup-res.c dies */
-
-/* export the pci_ DMA API in terms of the dma_ one */
-#include <asm-generic/pci-dma-compat.h>
-
-#ifdef CONFIG_PCI
-static inline void pci_dma_burst_advice(struct pci_dev *pdev,
-					enum pci_dma_burst_strategy *strat,
-					unsigned long *strategy_parameter)
-{
-	unsigned long cacheline_size;
-	u8 byte;
-
-	pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &byte);
-	if (byte == 0)
-		cacheline_size = 1024;
-	else
-		cacheline_size = (int) byte * 4;
-
-	*strat = PCI_DMA_BURST_MULTIPLE;
-	*strategy_parameter = cacheline_size;
-}
-#endif
-
-extern void
-pcibios_resource_to_bus(struct pci_dev *dev, struct pci_bus_region *region,
-			 struct resource *res);
-
-extern void
-pcibios_bus_to_resource(struct pci_dev *dev, struct resource *res,
-			struct pci_bus_region *region);
-
-static inline struct resource *
-pcibios_select_root(struct pci_dev *pdev, struct resource *res)
-{
-	struct resource *root = NULL;
-
-	if (res->flags & IORESOURCE_IO)
-		root = &ioport_resource;
-	if (res->flags & IORESOURCE_MEM)
-		root = &iomem_resource;
-
-	return root;
-}
-
-static inline void pcibios_penalize_isa_irq(int irq, int active)
-{
-	/* We don't need to penalize isa irq's */
-}
-
-static inline int pci_get_legacy_ide_irq(struct pci_dev *dev, int channel)
-{
-	return channel ? 15 : 14;
-}
-
-#endif /* __ASM_PARISC_PCI_H */