sh: migrate to arch/sh/include/

This follows the sparc changes a439fe51a1f8eb087c22dd24d69cebae4a3addac.

Most of the moving about was done with Sam's directions at:

http://marc.info/?l=linux-sh&m=121724823706062&w=2

with subsequent hacking and fixups entirely my fault.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

1 files changed, 0 insertions, 190 deletions

diff --git a/include/asm-sh/smc37c93x.h b/include/asm-sh/smc37c93x.h
deleted file mode 100644
index 585da2a8fc45..000000000000
--- a/include/asm-sh/smc37c93x.h
+++ /dev/null
@@ -1,190 +0,0 @@
-#ifndef __ASM_SH_SMC37C93X_H
-#define __ASM_SH_SMC37C93X_H
-
-/*
- * linux/include/asm-sh/smc37c93x.h
- *
- * Copyright (C) 2000  Kazumoto Kojima
- *
- * SMSC 37C93x Super IO Chip support
- */
-
-/* Default base I/O address */
-#define FDC_PRIMARY_BASE	0x3f0
-#define IDE1_PRIMARY_BASE	0x1f0
-#define IDE1_SECONDARY_BASE	0x170
-#define PARPORT_PRIMARY_BASE	0x378
-#define COM1_PRIMARY_BASE	0x2f8
-#define COM2_PRIMARY_BASE	0x3f8
-#define RTC_PRIMARY_BASE	0x070
-#define KBC_PRIMARY_BASE	0x060
-#define AUXIO_PRIMARY_BASE	0x000	/* XXX */
-
-/* Logical device number */
-#define LDN_FDC			0
-#define LDN_IDE1		1
-#define LDN_IDE2		2
-#define LDN_PARPORT		3
-#define LDN_COM1		4
-#define LDN_COM2		5
-#define LDN_RTC			6
-#define LDN_KBC			7
-#define LDN_AUXIO		8
-
-/* Configuration port and key */
-#define CONFIG_PORT		0x3f0
-#define INDEX_PORT		CONFIG_PORT
-#define DATA_PORT		0x3f1
-#define CONFIG_ENTER		0x55
-#define CONFIG_EXIT		0xaa
-
-/* Configuration index */
-#define CURRENT_LDN_INDEX	0x07
-#define POWER_CONTROL_INDEX	0x22
-#define ACTIVATE_INDEX		0x30
-#define IO_BASE_HI_INDEX	0x60
-#define IO_BASE_LO_INDEX	0x61
-#define IRQ_SELECT_INDEX	0x70
-#define DMA_SELECT_INDEX	0x74
-
-#define GPIO46_INDEX		0xc6
-#define GPIO47_INDEX		0xc7
-
-/* UART stuff. Only for debugging.  */
-/* UART Register */
-
-#define UART_RBR	0x0	/* Receiver Buffer Register (Read Only) */
-#define UART_THR	0x0	/* Transmitter Holding Register (Write Only) */
-#define UART_IER	0x2	/* Interrupt Enable Register */
-#define UART_IIR	0x4	/* Interrupt Ident Register (Read Only) */
-#define UART_FCR	0x4	/* FIFO Control Register (Write Only) */
-#define UART_LCR	0x6	/* Line Control Register */
-#define UART_MCR	0x8	/* MODEM Control Register */
-#define UART_LSR	0xa	/* Line Status Register */
-#define UART_MSR	0xc	/* MODEM Status Register */
-#define UART_SCR	0xe	/* Scratch Register */
-#define UART_DLL	0x0	/* Divisor Latch (LS) */
-#define UART_DLM	0x2	/* Divisor Latch (MS) */
-
-#ifndef __ASSEMBLY__
-typedef struct uart_reg {
-	volatile __u16 rbr;
-	volatile __u16 ier;
-	volatile __u16 iir;
-	volatile __u16 lcr;
-	volatile __u16 mcr;
-	volatile __u16 lsr;
-	volatile __u16 msr;
-	volatile __u16 scr;
-} uart_reg;
-#endif /* ! __ASSEMBLY__ */
-
-/* Alias for Write Only Register */
-
-#define thr	rbr
-#define tcr	iir
-
-/* Alias for Divisor Latch Register */
-
-#define dll	rbr
-#define dlm	ier
-#define fcr	iir
-
-/* Interrupt Enable Register */
-
-#define IER_ERDAI	0x0100	/* Enable Received Data Available Interrupt */
-#define IER_ETHREI	0x0200	/* Enable Transmitter Holding Register Empty Interrupt */
-#define IER_ELSI	0x0400	/* Enable Receiver Line Status Interrupt */
-#define IER_EMSI	0x0800	/* Enable MODEM Status Interrupt */
-
-/* Interrupt Ident Register */
-
-#define IIR_IP		0x0100	/* "0" if Interrupt Pending */
-#define IIR_IIB0	0x0200	/* Interrupt ID Bit 0 */
-#define IIR_IIB1	0x0400	/* Interrupt ID Bit 1 */
-#define IIR_IIB2	0x0800	/* Interrupt ID Bit 2 */
-#define IIR_FIFO	0xc000	/* FIFOs enabled */
-
-/* FIFO Control Register */
-
-#define FCR_FEN		0x0100	/* FIFO enable */
-#define FCR_RFRES	0x0200	/* Receiver FIFO reset */
-#define FCR_TFRES	0x0400	/* Transmitter FIFO reset */
-#define FCR_DMA		0x0800	/* DMA mode select */
-#define FCR_RTL		0x4000	/* Receiver triger (LSB) */
-#define FCR_RTM		0x8000	/* Receiver triger (MSB) */
-
-/* Line Control Register */
-
-#define LCR_WLS0	0x0100	/* Word Length Select Bit 0 */
-#define LCR_WLS1	0x0200	/* Word Length Select Bit 1 */
-#define LCR_STB		0x0400	/* Number of Stop Bits */
-#define LCR_PEN		0x0800	/* Parity Enable */
-#define LCR_EPS		0x1000	/* Even Parity Select */
-#define LCR_SP		0x2000	/* Stick Parity */
-#define LCR_SB		0x4000	/* Set Break */
-#define LCR_DLAB	0x8000	/* Divisor Latch Access Bit */
-
-/* MODEM Control Register */
-
-#define MCR_DTR		0x0100	/* Data Terminal Ready */
-#define MCR_RTS		0x0200	/* Request to Send */
-#define MCR_OUT1	0x0400	/* Out 1 */
-#define MCR_IRQEN	0x0800	/* IRQ Enable */
-#define MCR_LOOP	0x1000	/* Loop */
-
-/* Line Status Register */
-
-#define LSR_DR		0x0100	/* Data Ready */
-#define LSR_OE		0x0200	/* Overrun Error */
-#define LSR_PE		0x0400	/* Parity Error */
-#define LSR_FE		0x0800	/* Framing Error */
-#define LSR_BI		0x1000	/* Break Interrupt */
-#define LSR_THRE	0x2000	/* Transmitter Holding Register Empty */
-#define LSR_TEMT	0x4000	/* Transmitter Empty */
-#define LSR_FIFOE	0x8000	/* Receiver FIFO error */
-
-/* MODEM Status Register */
-
-#define MSR_DCTS	0x0100	/* Delta Clear to Send */
-#define MSR_DDSR	0x0200	/* Delta Data Set Ready */
-#define MSR_TERI	0x0400	/* Trailing Edge Ring Indicator */
-#define MSR_DDCD	0x0800	/* Delta Data Carrier Detect */
-#define MSR_CTS		0x1000	/* Clear to Send */
-#define MSR_DSR		0x2000	/* Data Set Ready */
-#define MSR_RI		0x4000	/* Ring Indicator */
-#define MSR_DCD		0x8000	/* Data Carrier Detect */
-
-/* Baud Rate Divisor */
-
-#define UART_CLK	(1843200)	/* 1.8432 MHz */
-#define UART_BAUD(x)	(UART_CLK / (16 * (x)))
-
-/* RTC register definition */
-#define RTC_SECONDS             0
-#define RTC_SECONDS_ALARM       1
-#define RTC_MINUTES             2
-#define RTC_MINUTES_ALARM       3
-#define RTC_HOURS               4
-#define RTC_HOURS_ALARM         5
-#define RTC_DAY_OF_WEEK         6
-#define RTC_DAY_OF_MONTH        7
-#define RTC_MONTH               8
-#define RTC_YEAR                9
-#define RTC_FREQ_SELECT		10
-# define RTC_UIP 0x80
-# define RTC_DIV_CTL 0x70
-/* This RTC can work under 32.768KHz clock only.  */
-# define RTC_OSC_ENABLE 0x20
-# define RTC_OSC_DISABLE 0x00
-#define RTC_CONTROL     	11
-# define RTC_SET 0x80
-# define RTC_PIE 0x40
-# define RTC_AIE 0x20
-# define RTC_UIE 0x10
-# define RTC_SQWE 0x08
-# define RTC_DM_BINARY 0x04
-# define RTC_24H 0x02
-# define RTC_DST_EN 0x01
-
-#endif  /* __ASM_SH_SMC37C93X_H */