Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
  [POWERPC] Add memchr() to the bootwrapper
  [POWERPC] Implement logging of unhandled signals
  [POWERPC] Add legacy serial support for OPB with flattened device tree
  [POWERPC] Use 1TB segments
  [POWERPC] XilinxFB: Allow fixed framebuffer base address
  [POWERPC] XilinxFB: Add support for custom screen resolution
  [POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
  [POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
  [POWERPC] 4xx: Kilauea defconfig file
  [POWERPC] 4xx: Kilauea DTS
  [POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
  [POWERPC] 4xx: Add AMCC 405EX support to cputable.c
  [POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
  [POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
  [POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
  [POWERPC] 85xx: Killed <asm/mpc85xx.h>
  [POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
  [POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
  [POWERPC] mpc8272ads: Remove muram from the CPM reg property.
  [POWERPC] Make clockevents work on PPC601 processors
  ...

Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.

78 files changed, 5412 insertions, 829 deletions

diff --git a/include/asm-powerpc/8xx_immap.h b/include/asm-powerpc/8xx_immap.h
new file mode 100644
index 000000000000..1311cefdfd30
--- /dev/null
+++ b/include/asm-powerpc/8xx_immap.h
@@ -0,0 +1,564 @@
+/*
+ * MPC8xx Internal Memory Map
+ * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
+ *
+ * The I/O on the MPC860 is comprised of blocks of special registers
+ * and the dual port ram for the Communication Processor Module.
+ * Within this space are functional units such as the SIU, memory
+ * controller, system timers, and other control functions.  It is
+ * a combination that I found difficult to separate into logical
+ * functional files.....but anyone else is welcome to try.  -- Dan
+ */
+#ifdef __KERNEL__
+#ifndef __IMMAP_8XX__
+#define __IMMAP_8XX__
+
+/* System configuration registers.
+*/
+typedef	struct sys_conf {
+	uint	sc_siumcr;
+	uint	sc_sypcr;
+	uint	sc_swt;
+	char	res1[2];
+	ushort	sc_swsr;
+	uint	sc_sipend;
+	uint	sc_simask;
+	uint	sc_siel;
+	uint	sc_sivec;
+	uint	sc_tesr;
+	char	res2[0xc];
+	uint	sc_sdcr;
+	char	res3[0x4c];
+} sysconf8xx_t;
+
+/* PCMCIA configuration registers.
+*/
+typedef struct pcmcia_conf {
+	uint	pcmc_pbr0;
+	uint	pcmc_por0;
+	uint	pcmc_pbr1;
+	uint	pcmc_por1;
+	uint	pcmc_pbr2;
+	uint	pcmc_por2;
+	uint	pcmc_pbr3;
+	uint	pcmc_por3;
+	uint	pcmc_pbr4;
+	uint	pcmc_por4;
+	uint	pcmc_pbr5;
+	uint	pcmc_por5;
+	uint	pcmc_pbr6;
+	uint	pcmc_por6;
+	uint	pcmc_pbr7;
+	uint	pcmc_por7;
+	char	res1[0x20];
+	uint	pcmc_pgcra;
+	uint	pcmc_pgcrb;
+	uint	pcmc_pscr;
+	char	res2[4];
+	uint	pcmc_pipr;
+	char	res3[4];
+	uint	pcmc_per;
+	char	res4[4];
+} pcmconf8xx_t;
+
+/* Memory controller registers.
+*/
+typedef struct	mem_ctlr {
+	uint	memc_br0;
+	uint	memc_or0;
+	uint	memc_br1;
+	uint	memc_or1;
+	uint	memc_br2;
+	uint	memc_or2;
+	uint	memc_br3;
+	uint	memc_or3;
+	uint	memc_br4;
+	uint	memc_or4;
+	uint	memc_br5;
+	uint	memc_or5;
+	uint	memc_br6;
+	uint	memc_or6;
+	uint	memc_br7;
+	uint	memc_or7;
+	char	res1[0x24];
+	uint	memc_mar;
+	uint	memc_mcr;
+	char	res2[4];
+	uint	memc_mamr;
+	uint	memc_mbmr;
+	ushort	memc_mstat;
+	ushort	memc_mptpr;
+	uint	memc_mdr;
+	char	res3[0x80];
+} memctl8xx_t;
+
+/*-----------------------------------------------------------------------
+ * BR - Memory Controler: Base Register					16-9
+ */
+#define BR_BA_MSK	0xffff8000	/* Base Address Mask			*/
+#define BR_AT_MSK	0x00007000	/* Address Type Mask			*/
+#define BR_PS_MSK	0x00000c00	/* Port Size Mask			*/
+#define BR_PS_32	0x00000000	/* 32 bit port size			*/
+#define BR_PS_16	0x00000800	/* 16 bit port size			*/
+#define BR_PS_8		0x00000400	/*  8 bit port size			*/
+#define BR_PARE		0x00000200	/* Parity Enable			*/
+#define BR_WP		0x00000100	/* Write Protect			*/
+#define BR_MS_MSK	0x000000c0	/* Machine Select Mask			*/
+#define BR_MS_GPCM	0x00000000	/* G.P.C.M. Machine Select		*/
+#define BR_MS_UPMA	0x00000080	/* U.P.M.A Machine Select		*/
+#define BR_MS_UPMB	0x000000c0	/* U.P.M.B Machine Select		*/
+#define BR_V		0x00000001	/* Bank Valid				*/
+
+/*-----------------------------------------------------------------------
+ * OR - Memory Controler: Option Register				16-11
+ */
+#define OR_AM_MSK	0xffff8000	/* Address Mask Mask			*/
+#define OR_ATM_MSK	0x00007000	/* Address Type Mask Mask		*/
+#define OR_CSNT_SAM	0x00000800	/* Chip Select Negation Time/ Start	*/
+					/* Address Multiplex			*/
+#define OR_ACS_MSK	0x00000600	/* Address to Chip Select Setup mask	*/
+#define OR_ACS_DIV1	0x00000000	/* CS is output at the same time	*/
+#define OR_ACS_DIV4	0x00000400	/* CS is output 1/4 a clock later	*/
+#define OR_ACS_DIV2	0x00000600	/* CS is output 1/2 a clock later	*/
+#define OR_G5LA		0x00000400	/* Output #GPL5 on #GPL_A5		*/
+#define OR_G5LS		0x00000200	/* Drive #GPL high on falling edge of...*/
+#define OR_BI		0x00000100	/* Burst inhibit			*/
+#define OR_SCY_MSK	0x000000f0	/* Cycle Lenght in Clocks		*/
+#define OR_SCY_0_CLK	0x00000000	/* 0 clock cycles wait states		*/
+#define OR_SCY_1_CLK	0x00000010	/* 1 clock cycles wait states		*/
+#define OR_SCY_2_CLK	0x00000020	/* 2 clock cycles wait states		*/
+#define OR_SCY_3_CLK	0x00000030	/* 3 clock cycles wait states		*/
+#define OR_SCY_4_CLK	0x00000040	/* 4 clock cycles wait states		*/
+#define OR_SCY_5_CLK	0x00000050	/* 5 clock cycles wait states		*/
+#define OR_SCY_6_CLK	0x00000060	/* 6 clock cycles wait states		*/
+#define OR_SCY_7_CLK	0x00000070	/* 7 clock cycles wait states		*/
+#define OR_SCY_8_CLK	0x00000080	/* 8 clock cycles wait states		*/
+#define OR_SCY_9_CLK	0x00000090	/* 9 clock cycles wait states		*/
+#define OR_SCY_10_CLK	0x000000a0	/* 10 clock cycles wait states		*/
+#define OR_SCY_11_CLK	0x000000b0	/* 11 clock cycles wait states		*/
+#define OR_SCY_12_CLK	0x000000c0	/* 12 clock cycles wait states		*/
+#define OR_SCY_13_CLK	0x000000d0	/* 13 clock cycles wait states		*/
+#define OR_SCY_14_CLK	0x000000e0	/* 14 clock cycles wait states		*/
+#define OR_SCY_15_CLK	0x000000f0	/* 15 clock cycles wait states		*/
+#define OR_SETA		0x00000008	/* External Transfer Acknowledge	*/
+#define OR_TRLX		0x00000004	/* Timing Relaxed			*/
+#define OR_EHTR		0x00000002	/* Extended Hold Time on Read		*/
+
+/* System Integration Timers.
+*/
+typedef struct	sys_int_timers {
+	ushort	sit_tbscr;
+	char	res0[0x02];
+	uint	sit_tbreff0;
+	uint	sit_tbreff1;
+	char	res1[0x14];
+	ushort	sit_rtcsc;
+	char	res2[0x02];
+	uint	sit_rtc;
+	uint	sit_rtsec;
+	uint	sit_rtcal;
+	char	res3[0x10];
+	ushort	sit_piscr;
+	char	res4[2];
+	uint	sit_pitc;
+	uint	sit_pitr;
+	char	res5[0x34];
+} sit8xx_t;
+
+#define TBSCR_TBIRQ_MASK	((ushort)0xff00)
+#define TBSCR_REFA		((ushort)0x0080)
+#define TBSCR_REFB		((ushort)0x0040)
+#define TBSCR_REFAE		((ushort)0x0008)
+#define TBSCR_REFBE		((ushort)0x0004)
+#define TBSCR_TBF		((ushort)0x0002)
+#define TBSCR_TBE		((ushort)0x0001)
+
+#define RTCSC_RTCIRQ_MASK	((ushort)0xff00)
+#define RTCSC_SEC		((ushort)0x0080)
+#define RTCSC_ALR		((ushort)0x0040)
+#define RTCSC_38K		((ushort)0x0010)
+#define RTCSC_SIE		((ushort)0x0008)
+#define RTCSC_ALE		((ushort)0x0004)
+#define RTCSC_RTF		((ushort)0x0002)
+#define RTCSC_RTE		((ushort)0x0001)
+
+#define PISCR_PIRQ_MASK		((ushort)0xff00)
+#define PISCR_PS		((ushort)0x0080)
+#define PISCR_PIE		((ushort)0x0004)
+#define PISCR_PTF		((ushort)0x0002)
+#define PISCR_PTE		((ushort)0x0001)
+
+/* Clocks and Reset.
+*/
+typedef struct clk_and_reset {
+	uint	car_sccr;
+	uint	car_plprcr;
+	uint	car_rsr;
+	char	res[0x74];        /* Reserved area                  */
+} car8xx_t;
+
+/* System Integration Timers keys.
+*/
+typedef struct sitk {
+	uint	sitk_tbscrk;
+	uint	sitk_tbreff0k;
+	uint	sitk_tbreff1k;
+	uint	sitk_tbk;
+	char	res1[0x10];
+	uint	sitk_rtcsck;
+	uint	sitk_rtck;
+	uint	sitk_rtseck;
+	uint	sitk_rtcalk;
+	char	res2[0x10];
+	uint	sitk_piscrk;
+	uint	sitk_pitck;
+	char	res3[0x38];
+} sitk8xx_t;
+
+/* Clocks and reset keys.
+*/
+typedef struct cark {
+	uint	cark_sccrk;
+	uint	cark_plprcrk;
+	uint	cark_rsrk;
+	char	res[0x474];
+} cark8xx_t;
+
+/* The key to unlock registers maintained by keep-alive power.
+*/
+#define KAPWR_KEY	((unsigned int)0x55ccaa33)
+
+/* Video interface.  MPC823 Only.
+*/
+typedef struct vid823 {
+	ushort	vid_vccr;
+	ushort	res1;
+	u_char	vid_vsr;
+	u_char	res2;
+	u_char	vid_vcmr;
+	u_char	res3;
+	uint	vid_vbcb;
+	uint	res4;
+	uint	vid_vfcr0;
+	uint	vid_vfaa0;
+	uint	vid_vfba0;
+	uint	vid_vfcr1;
+	uint	vid_vfaa1;
+	uint	vid_vfba1;
+	u_char	res5[0x18];
+} vid823_t;
+
+/* LCD interface.  823 Only.
+*/
+typedef struct lcd {
+	uint	lcd_lccr;
+	uint	lcd_lchcr;
+	uint	lcd_lcvcr;
+	char	res1[4];
+	uint	lcd_lcfaa;
+	uint	lcd_lcfba;
+	char	lcd_lcsr;
+	char	res2[0x7];
+} lcd823_t;
+
+/* I2C
+*/
+typedef struct i2c {
+	u_char	i2c_i2mod;
+	char	res1[3];
+	u_char	i2c_i2add;
+	char	res2[3];
+	u_char	i2c_i2brg;
+	char	res3[3];
+	u_char	i2c_i2com;
+	char	res4[3];
+	u_char	i2c_i2cer;
+	char	res5[3];
+	u_char	i2c_i2cmr;
+	char	res6[0x8b];
+} i2c8xx_t;
+
+/* DMA control/status registers.
+*/
+typedef struct sdma_csr {
+	char	res1[4];
+	uint	sdma_sdar;
+	u_char	sdma_sdsr;
+	char	res3[3];
+	u_char	sdma_sdmr;
+	char	res4[3];
+	u_char	sdma_idsr1;
+	char	res5[3];
+	u_char	sdma_idmr1;
+	char	res6[3];
+	u_char	sdma_idsr2;
+	char	res7[3];
+	u_char	sdma_idmr2;
+	char	res8[0x13];
+} sdma8xx_t;
+
+/* Communication Processor Module Interrupt Controller.
+*/
+typedef struct cpm_ic {
+	ushort	cpic_civr;
+	char	res[0xe];
+	uint	cpic_cicr;
+	uint	cpic_cipr;
+	uint	cpic_cimr;
+	uint	cpic_cisr;
+} cpic8xx_t;
+
+/* Input/Output Port control/status registers.
+*/
+typedef struct io_port {
+	ushort	iop_padir;
+	ushort	iop_papar;
+	ushort	iop_paodr;
+	ushort	iop_padat;
+	char	res1[8];
+	ushort	iop_pcdir;
+	ushort	iop_pcpar;
+	ushort	iop_pcso;
+	ushort	iop_pcdat;
+	ushort	iop_pcint;
+	char	res2[6];
+	ushort	iop_pddir;
+	ushort	iop_pdpar;
+	char	res3[2];
+	ushort	iop_pddat;
+	uint	utmode;
+	char	res4[4];
+} iop8xx_t;
+
+/* Communication Processor Module Timers
+*/
+typedef struct cpm_timers {
+	ushort	cpmt_tgcr;
+	char	res1[0xe];
+	ushort	cpmt_tmr1;
+	ushort	cpmt_tmr2;
+	ushort	cpmt_trr1;
+	ushort	cpmt_trr2;
+	ushort	cpmt_tcr1;
+	ushort	cpmt_tcr2;
+	ushort	cpmt_tcn1;
+	ushort	cpmt_tcn2;
+	ushort	cpmt_tmr3;
+	ushort	cpmt_tmr4;
+	ushort	cpmt_trr3;
+	ushort	cpmt_trr4;
+	ushort	cpmt_tcr3;
+	ushort	cpmt_tcr4;
+	ushort	cpmt_tcn3;
+	ushort	cpmt_tcn4;
+	ushort	cpmt_ter1;
+	ushort	cpmt_ter2;
+	ushort	cpmt_ter3;
+	ushort	cpmt_ter4;
+	char	res2[8];
+} cpmtimer8xx_t;
+
+/* Finally, the Communication Processor stuff.....
+*/
+typedef struct scc {		/* Serial communication channels */
+	uint	scc_gsmrl;
+	uint	scc_gsmrh;
+	ushort	scc_psmr;
+	char	res1[2];
+	ushort	scc_todr;
+	ushort	scc_dsr;
+	ushort	scc_scce;
+	char	res2[2];
+	ushort	scc_sccm;
+	char	res3;
+	u_char	scc_sccs;
+	char	res4[8];
+} scc_t;
+
+typedef struct smc {		/* Serial management channels */
+	char	res1[2];
+	ushort	smc_smcmr;
+	char	res2[2];
+	u_char	smc_smce;
+	char	res3[3];
+	u_char	smc_smcm;
+	char	res4[5];
+} smc_t;
+
+/* MPC860T Fast Ethernet Controller.  It isn't part of the CPM, but
+ * it fits within the address space.
+ */
+
+typedef struct fec {
+	uint	fec_addr_low;		/* lower 32 bits of station address	*/
+	ushort	fec_addr_high;		/* upper 16 bits of station address	*/
+	ushort	res1;			/* reserved				*/
+	uint	fec_hash_table_high;	/* upper 32-bits of hash table		*/
+	uint	fec_hash_table_low;	/* lower 32-bits of hash table		*/
+	uint	fec_r_des_start;	/* beginning of Rx descriptor ring	*/
+	uint	fec_x_des_start;	/* beginning of Tx descriptor ring	*/
+	uint	fec_r_buff_size;	/* Rx buffer size			*/
+	uint	res2[9];		/* reserved				*/
+	uint	fec_ecntrl;		/* ethernet control register		*/
+	uint	fec_ievent;		/* interrupt event register		*/
+	uint	fec_imask;		/* interrupt mask register		*/
+	uint	fec_ivec;		/* interrupt level and vector status	*/
+	uint	fec_r_des_active;	/* Rx ring updated flag			*/
+	uint	fec_x_des_active;	/* Tx ring updated flag			*/
+	uint	res3[10];		/* reserved				*/
+	uint	fec_mii_data;		/* MII data register			*/
+	uint	fec_mii_speed;		/* MII speed control register		*/
+	uint	res4[17];		/* reserved				*/
+	uint	fec_r_bound;		/* end of RAM (read-only)		*/
+	uint	fec_r_fstart;		/* Rx FIFO start address		*/
+	uint	res5[6];		/* reserved				*/
+	uint	fec_x_fstart;		/* Tx FIFO start address		*/
+	uint	res6[17];		/* reserved				*/
+	uint	fec_fun_code;		/* fec SDMA function code		*/
+	uint	res7[3];		/* reserved				*/
+	uint	fec_r_cntrl;		/* Rx control register			*/
+	uint	fec_r_hash;		/* Rx hash register			*/
+	uint	res8[14];		/* reserved				*/
+	uint	fec_x_cntrl;		/* Tx control register			*/
+	uint	res9[0x1e];		/* reserved				*/
+} fec_t;
+
+/* The FEC and LCD color map share the same address space....
+ * I guess we will never see an 823T :-).
+ */
+union fec_lcd {
+	fec_t	fl_un_fec;
+	u_char	fl_un_cmap[0x200];
+};
+
+typedef struct comm_proc {
+	/* General control and status registers.
+	*/
+	ushort	cp_cpcr;
+	u_char	res1[2];
+	ushort	cp_rccr;
+	u_char	res2;
+	u_char	cp_rmds;
+	u_char	res3[4];
+	ushort	cp_cpmcr1;
+	ushort	cp_cpmcr2;
+	ushort	cp_cpmcr3;
+	ushort	cp_cpmcr4;
+	u_char	res4[2];
+	ushort	cp_rter;
+	u_char	res5[2];
+	ushort	cp_rtmr;
+	u_char	res6[0x14];
+
+	/* Baud rate generators.
+	*/
+	uint	cp_brgc1;
+	uint	cp_brgc2;
+	uint	cp_brgc3;
+	uint	cp_brgc4;
+
+	/* Serial Communication Channels.
+	*/
+	scc_t	cp_scc[4];
+
+	/* Serial Management Channels.
+	*/
+	smc_t	cp_smc[2];
+
+	/* Serial Peripheral Interface.
+	*/
+	ushort	cp_spmode;
+	u_char	res7[4];
+	u_char	cp_spie;
+	u_char	res8[3];
+	u_char	cp_spim;
+	u_char	res9[2];
+	u_char	cp_spcom;
+	u_char	res10[2];
+
+	/* Parallel Interface Port.
+	*/
+	u_char	res11[2];
+	ushort	cp_pipc;
+	u_char	res12[2];
+	ushort	cp_ptpr;
+	uint	cp_pbdir;
+	uint	cp_pbpar;
+	u_char	res13[2];
+	ushort	cp_pbodr;
+	uint	cp_pbdat;
+
+	/* Port E - MPC87x/88x only.
+	 */
+	uint	cp_pedir;
+	uint	cp_pepar;
+	uint	cp_peso;
+	uint	cp_peodr;
+	uint	cp_pedat;
+
+	/* Communications Processor Timing Register -
+	   Contains RMII Timing for the FECs on MPC87x/88x only.
+	*/
+	uint	cp_cptr;
+
+	/* Serial Interface and Time Slot Assignment.
+	*/
+	uint	cp_simode;
+	u_char	cp_sigmr;
+	u_char	res15;
+	u_char	cp_sistr;
+	u_char	cp_sicmr;
+	u_char	res16[4];
+	uint	cp_sicr;
+	uint	cp_sirp;
+	u_char	res17[0xc];
+
+	/* 256 bytes of MPC823 video controller RAM array.
+	*/
+	u_char	cp_vcram[0x100];
+	u_char	cp_siram[0x200];
+
+	/* The fast ethernet controller is not really part of the CPM,
+	 * but it resides in the address space.
+	 * The LCD color map is also here.
+	 */
+	union	fec_lcd	fl_un;
+#define cp_fec		fl_un.fl_un_fec
+#define lcd_cmap	fl_un.fl_un_cmap
+	char	res18[0xE00];
+
+	/* The DUET family has a second FEC here */
+	fec_t	cp_fec2;
+#define cp_fec1	cp_fec	/* consistency macro */
+
+	/* Dual Ported RAM follows.
+	 * There are many different formats for this memory area
+	 * depending upon the devices used and options chosen.
+	 * Some processors don't have all of it populated.
+	 */
+	u_char	cp_dpmem[0x1C00];	/* BD / Data / ucode */
+	u_char	cp_dparam[0x400];	/* Parameter RAM */
+} cpm8xx_t;
+
+/* Internal memory map.
+*/
+typedef struct immap {
+	sysconf8xx_t	im_siu_conf;	/* SIU Configuration */
+	pcmconf8xx_t	im_pcmcia;	/* PCMCIA Configuration */
+	memctl8xx_t	im_memctl;	/* Memory Controller */
+	sit8xx_t	im_sit;		/* System integration timers */
+	car8xx_t	im_clkrst;	/* Clocks and reset */
+	sitk8xx_t	im_sitk;	/* Sys int timer keys */
+	cark8xx_t	im_clkrstk;	/* Clocks and reset keys */
+	vid823_t	im_vid;		/* Video (823 only) */
+	lcd823_t	im_lcd;		/* LCD (823 only) */
+	i2c8xx_t	im_i2c;		/* I2C control/status */
+	sdma8xx_t	im_sdma;	/* SDMA control/status */
+	cpic8xx_t	im_cpic;	/* CPM Interrupt Controller */
+	iop8xx_t	im_ioport;	/* IO Port control/status */
+	cpmtimer8xx_t	im_cpmtimer;	/* CPM timers */
+	cpm8xx_t	im_cpm;		/* Communication processor */
+} immap_t;
+
+#endif /* __IMMAP_8XX__ */
+#endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/atomic.h b/include/asm-powerpc/atomic.h
index c44810b9d322..f3fc733758f5 100644
--- a/include/asm-powerpc/atomic.h
+++ b/include/asm-powerpc/atomic.h
@@ -5,7 +5,7 @@
  * PowerPC atomic operations
  */
 
-typedef struct { volatile int counter; } atomic_t;
+typedef struct { int counter; } atomic_t;
 
 #ifdef __KERNEL__
 #include <linux/compiler.h>
@@ -15,8 +15,19 @@ typedef struct { volatile int counter; } atomic_t;
 
 #define ATOMIC_INIT(i)		{ (i) }
 
-#define atomic_read(v)		((v)->counter)
-#define atomic_set(v,i)		(((v)->counter) = (i))
+static __inline__ int atomic_read(const atomic_t *v)
+{
+	int t;
+
+	__asm__ __volatile__("lwz%U1%X1 %0,%1" : "=r"(t) : "m"(v->counter));
+
+	return t;
+}
+
+static __inline__ void atomic_set(atomic_t *v, int i)
+{
+	__asm__ __volatile__("stw%U0%X0 %1,%0" : "=m"(v->counter) : "r"(i));
+}
 
 static __inline__ void atomic_add(int a, atomic_t *v)
 {
@@ -240,12 +251,23 @@ static __inline__ int atomic_dec_if_positive(atomic_t *v)
 
 #ifdef __powerpc64__
 
-typedef struct { volatile long counter; } atomic64_t;
+typedef struct { long counter; } atomic64_t;
 
 #define ATOMIC64_INIT(i)	{ (i) }
 
-#define atomic64_read(v)	((v)->counter)
-#define atomic64_set(v,i)	(((v)->counter) = (i))
+static __inline__ long atomic64_read(const atomic64_t *v)
+{
+	long t;
+
+	__asm__ __volatile__("ld%U1%X1 %0,%1" : "=r"(t) : "m"(v->counter));
+
+	return t;
+}
+
+static __inline__ void atomic64_set(atomic64_t *v, long i)
+{
+	__asm__ __volatile__("std%U0%X0 %1,%0" : "=m"(v->counter) : "r"(i));
+}
 
 static __inline__ void atomic64_add(long a, atomic64_t *v)
 {
diff --git a/include/asm-powerpc/cell-regs.h b/include/asm-powerpc/cell-regs.h
new file mode 100644
index 000000000000..fd6fd00434ef
--- /dev/null
+++ b/include/asm-powerpc/cell-regs.h
@@ -0,0 +1,315 @@
+/*
+ * cbe_regs.h
+ *
+ * This file is intended to hold the various register definitions for CBE
+ * on-chip system devices (memory controller, IO controller, etc...)
+ *
+ * (C) Copyright IBM Corporation 2001,2006
+ *
+ * Authors: Maximino Aguilar (maguilar@us.ibm.com)
+ *          David J. Erb (djerb@us.ibm.com)
+ *
+ * (c) 2006 Benjamin Herrenschmidt <benh@kernel.crashing.org>, IBM Corp.
+ */
+
+#ifndef CBE_REGS_H
+#define CBE_REGS_H
+
+#include <asm/cell-pmu.h>
+
+/*
+ *
+ * Some HID register definitions
+ *
+ */
+
+/* CBE specific HID0 bits */
+#define HID0_CBE_THERM_WAKEUP	0x0000020000000000ul
+#define HID0_CBE_SYSERR_WAKEUP	0x0000008000000000ul
+#define HID0_CBE_THERM_INT_EN	0x0000000400000000ul
+#define HID0_CBE_SYSERR_INT_EN	0x0000000200000000ul
+
+#define MAX_CBE		2
+
+/*
+ *
+ * Pervasive unit register definitions
+ *
+ */
+
+union spe_reg {
+	u64 val;
+	u8 spe[8];
+};
+
+union ppe_spe_reg {
+	u64 val;
+	struct {
+		u32 ppe;
+		u32 spe;
+	};
+};
+
+
+struct cbe_pmd_regs {
+	/* Debug Bus Control */
+	u64	pad_0x0000;					/* 0x0000 */
+
+	u64	group_control;					/* 0x0008 */
+
+	u8	pad_0x0010_0x00a8 [0x00a8 - 0x0010];		/* 0x0010 */
+
+	u64	debug_bus_control;				/* 0x00a8 */
+
+	u8	pad_0x00b0_0x0100 [0x0100 - 0x00b0];		/* 0x00b0 */
+
+	u64	trace_aux_data;					/* 0x0100 */
+	u64	trace_buffer_0_63;				/* 0x0108 */
+	u64	trace_buffer_64_127;				/* 0x0110 */
+	u64	trace_address;					/* 0x0118 */
+	u64	ext_tr_timer;					/* 0x0120 */
+
+	u8	pad_0x0128_0x0400 [0x0400 - 0x0128];		/* 0x0128 */
+
+	/* Performance Monitor */
+	u64	pm_status;					/* 0x0400 */
+	u64	pm_control;					/* 0x0408 */
+	u64	pm_interval;					/* 0x0410 */
+	u64	pm_ctr[4];					/* 0x0418 */
+	u64	pm_start_stop;					/* 0x0438 */
+	u64	pm07_control[8];				/* 0x0440 */
+
+	u8	pad_0x0480_0x0800 [0x0800 - 0x0480];		/* 0x0480 */
+
+	/* Thermal Sensor Registers */
+	union	spe_reg	ts_ctsr1;				/* 0x0800 */
+	u64	ts_ctsr2;					/* 0x0808 */
+	union	spe_reg	ts_mtsr1;				/* 0x0810 */
+	u64	ts_mtsr2;					/* 0x0818 */
+	union	spe_reg	ts_itr1;				/* 0x0820 */
+	u64	ts_itr2;					/* 0x0828 */
+	u64	ts_gitr;					/* 0x0830 */
+	u64	ts_isr;						/* 0x0838 */
+	u64	ts_imr;						/* 0x0840 */
+	union	spe_reg	tm_cr1;					/* 0x0848 */
+	u64	tm_cr2;						/* 0x0850 */
+	u64	tm_simr;					/* 0x0858 */
+	union	ppe_spe_reg tm_tpr;				/* 0x0860 */
+	union	spe_reg	tm_str1;				/* 0x0868 */
+	u64	tm_str2;					/* 0x0870 */
+	union	ppe_spe_reg tm_tsr;				/* 0x0878 */
+
+	/* Power Management */
+	u64	pmcr;						/* 0x0880 */
+#define CBE_PMD_PAUSE_ZERO_CONTROL	0x10000
+	u64	pmsr;						/* 0x0888 */
+
+	/* Time Base Register */
+	u64	tbr;						/* 0x0890 */
+
+	u8	pad_0x0898_0x0c00 [0x0c00 - 0x0898];		/* 0x0898 */
+
+	/* Fault Isolation Registers */
+	u64	checkstop_fir;					/* 0x0c00 */
+	u64	recoverable_fir;				/* 0x0c08 */
+	u64	spec_att_mchk_fir;				/* 0x0c10 */
+	u32	fir_mode_reg;					/* 0x0c18 */
+	u8	pad_0x0c1c_0x0c20 [4];				/* 0x0c1c */
+#define CBE_PMD_FIR_MODE_M8		0x00800
+	u64	fir_enable_mask;				/* 0x0c20 */
+
+	u8	pad_0x0c28_0x0ca8 [0x0ca8 - 0x0c28];		/* 0x0c28 */
+	u64	ras_esc_0;					/* 0x0ca8 */
+	u8	pad_0x0cb0_0x1000 [0x1000 - 0x0cb0];		/* 0x0cb0 */
+};
+
+extern struct cbe_pmd_regs __iomem *cbe_get_pmd_regs(struct device_node *np);
+extern struct cbe_pmd_regs __iomem *cbe_get_cpu_pmd_regs(int cpu);
+
+/*
+ * PMU shadow registers
+ *
+ * Many of the registers in the performance monitoring unit are write-only,
+ * so we need to save a copy of what we write to those registers.
+ *
+ * The actual data counters are read/write. However, writing to the counters
+ * only takes effect if the PMU is enabled. Otherwise the value is stored in
+ * a hardware latch until the next time the PMU is enabled. So we save a copy
+ * of the counter values if we need to read them back while the PMU is
+ * disabled. The counter_value_in_latch field is a bitmap indicating which
+ * counters currently have a value waiting to be written.
+ */
+
+struct cbe_pmd_shadow_regs {
+	u32 group_control;
+	u32 debug_bus_control;
+	u32 trace_address;
+	u32 ext_tr_timer;
+	u32 pm_status;
+	u32 pm_control;
+	u32 pm_interval;
+	u32 pm_start_stop;
+	u32 pm07_control[NR_CTRS];
+
+	u32 pm_ctr[NR_PHYS_CTRS];
+	u32 counter_value_in_latch;
+};
+
+extern struct cbe_pmd_shadow_regs *cbe_get_pmd_shadow_regs(struct device_node *np);
+extern struct cbe_pmd_shadow_regs *cbe_get_cpu_pmd_shadow_regs(int cpu);
+
+/*
+ *
+ * IIC unit register definitions
+ *
+ */
+
+struct cbe_iic_pending_bits {
+	u32 data;
+	u8 flags;
+	u8 class;
+	u8 source;
+	u8 prio;
+};
+
+#define CBE_IIC_IRQ_VALID	0x80
+#define CBE_IIC_IRQ_IPI		0x40
+
+struct cbe_iic_thread_regs {
+	struct cbe_iic_pending_bits pending;
+	struct cbe_iic_pending_bits pending_destr;
+	u64 generate;
+	u64 prio;
+};
+
+struct cbe_iic_regs {
+	u8	pad_0x0000_0x0400[0x0400 - 0x0000];		/* 0x0000 */
+
+	/* IIC interrupt registers */
+	struct	cbe_iic_thread_regs thread[2];			/* 0x0400 */
+
+	u64	iic_ir;						/* 0x0440 */
+#define CBE_IIC_IR_PRIO(x)      (((x) & 0xf) << 12)
+#define CBE_IIC_IR_DEST_NODE(x) (((x) & 0xf) << 4)
+#define CBE_IIC_IR_DEST_UNIT(x) ((x) & 0xf)
+#define CBE_IIC_IR_IOC_0        0x0
+#define CBE_IIC_IR_IOC_1S       0xb
+#define CBE_IIC_IR_PT_0         0xe
+#define CBE_IIC_IR_PT_1         0xf
+
+	u64	iic_is;						/* 0x0448 */
+#define CBE_IIC_IS_PMI		0x2
+
+	u8	pad_0x0450_0x0500[0x0500 - 0x0450];		/* 0x0450 */
+
+	/* IOC FIR */
+	u64	ioc_fir_reset;					/* 0x0500 */
+	u64	ioc_fir_set;					/* 0x0508 */
+	u64	ioc_checkstop_enable;				/* 0x0510 */
+	u64	ioc_fir_error_mask;				/* 0x0518 */
+	u64	ioc_syserr_enable;				/* 0x0520 */
+	u64	ioc_fir;					/* 0x0528 */
+
+	u8	pad_0x0530_0x1000[0x1000 - 0x0530];		/* 0x0530 */
+};
+
+extern struct cbe_iic_regs __iomem *cbe_get_iic_regs(struct device_node *np);
+extern struct cbe_iic_regs __iomem *cbe_get_cpu_iic_regs(int cpu);
+
+
+struct cbe_mic_tm_regs {
+	u8	pad_0x0000_0x0040[0x0040 - 0x0000];		/* 0x0000 */
+
+	u64	mic_ctl_cnfg2;					/* 0x0040 */
+#define CBE_MIC_ENABLE_AUX_TRC		0x8000000000000000LL
+#define CBE_MIC_DISABLE_PWR_SAV_2	0x0200000000000000LL
+#define CBE_MIC_DISABLE_AUX_TRC_WRAP	0x0100000000000000LL
+#define CBE_MIC_ENABLE_AUX_TRC_INT	0x0080000000000000LL
+
+	u64	pad_0x0048;					/* 0x0048 */
+
+	u64	mic_aux_trc_base;				/* 0x0050 */
+	u64	mic_aux_trc_max_addr;				/* 0x0058 */
+	u64	mic_aux_trc_cur_addr;				/* 0x0060 */
+	u64	mic_aux_trc_grf_addr;				/* 0x0068 */
+	u64	mic_aux_trc_grf_data;				/* 0x0070 */
+
+	u64	pad_0x0078;					/* 0x0078 */
+
+	u64	mic_ctl_cnfg_0;					/* 0x0080 */
+#define CBE_MIC_DISABLE_PWR_SAV_0	0x8000000000000000LL
+
+	u64	pad_0x0088;					/* 0x0088 */
+
+	u64	slow_fast_timer_0;				/* 0x0090 */
+	u64	slow_next_timer_0;				/* 0x0098 */
+
+	u8	pad_0x00a0_0x00f8[0x00f8 - 0x00a0];		/* 0x00a0 */
+	u64    	mic_df_ecc_address_0;				/* 0x00f8 */
+
+	u8	pad_0x0100_0x01b8[0x01b8 - 0x0100];		/* 0x0100 */
+	u64    	mic_df_ecc_address_1;				/* 0x01b8 */
+
+	u64	mic_ctl_cnfg_1;					/* 0x01c0 */
+#define CBE_MIC_DISABLE_PWR_SAV_1	0x8000000000000000LL
+
+	u64	pad_0x01c8;					/* 0x01c8 */
+
+	u64	slow_fast_timer_1;				/* 0x01d0 */
+	u64	slow_next_timer_1;				/* 0x01d8 */
+
+	u8	pad_0x01e0_0x0208[0x0208 - 0x01e0];		/* 0x01e0 */
+	u64	mic_exc;					/* 0x0208 */
+#define CBE_MIC_EXC_BLOCK_SCRUB		0x0800000000000000ULL
+#define CBE_MIC_EXC_FAST_SCRUB		0x0100000000000000ULL
+
+	u64	mic_mnt_cfg;					/* 0x0210 */
+#define CBE_MIC_MNT_CFG_CHAN_0_POP	0x0002000000000000ULL
+#define CBE_MIC_MNT_CFG_CHAN_1_POP	0x0004000000000000ULL
+
+	u64	mic_df_config;					/* 0x0218 */
+#define CBE_MIC_ECC_DISABLE_0		0x4000000000000000ULL
+#define CBE_MIC_ECC_REP_SINGLE_0	0x2000000000000000ULL
+#define CBE_MIC_ECC_DISABLE_1		0x0080000000000000ULL
+#define CBE_MIC_ECC_REP_SINGLE_1	0x0040000000000000ULL
+
+	u8	pad_0x0220_0x0230[0x0230 - 0x0220];		/* 0x0220 */
+	u64	mic_fir;					/* 0x0230 */
+#define CBE_MIC_FIR_ECC_SINGLE_0_ERR	0x0200000000000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_0_ERR	0x0100000000000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_1_ERR	0x0080000000000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_1_ERR	0x0040000000000000ULL
+#define CBE_MIC_FIR_ECC_ERR_MASK	0xffff000000000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_0_CTE	0x0000020000000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_0_CTE	0x0000010000000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_1_CTE	0x0000008000000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_1_CTE	0x0000004000000000ULL
+#define CBE_MIC_FIR_ECC_CTE_MASK	0x0000ffff00000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_0_RESET	0x0000000002000000ULL
+#define CBE_MIC_FIR_ECC_MULTI_0_RESET	0x0000000001000000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_1_RESET	0x0000000000800000ULL
+#define CBE_MIC_FIR_ECC_MULTI_1_RESET	0x0000000000400000ULL
+#define CBE_MIC_FIR_ECC_RESET_MASK	0x00000000ffff0000ULL
+#define CBE_MIC_FIR_ECC_SINGLE_0_SET	0x0000000000000200ULL
+#define CBE_MIC_FIR_ECC_MULTI_0_SET	0x0000000000000100ULL
+#define CBE_MIC_FIR_ECC_SINGLE_1_SET	0x0000000000000080ULL
+#define CBE_MIC_FIR_ECC_MULTI_1_SET	0x0000000000000040ULL
+#define CBE_MIC_FIR_ECC_SET_MASK	0x000000000000ffffULL
+	u64	mic_fir_debug;					/* 0x0238 */
+
+	u8	pad_0x0240_0x1000[0x1000 - 0x0240];		/* 0x0240 */
+};
+
+extern struct cbe_mic_tm_regs __iomem *cbe_get_mic_tm_regs(struct device_node *np);
+extern struct cbe_mic_tm_regs __iomem *cbe_get_cpu_mic_tm_regs(int cpu);
+
+/* some utility functions to deal with SMT */
+extern u32 cbe_get_hw_thread_id(int cpu);
+extern u32 cbe_cpu_to_node(int cpu);
+extern u32 cbe_node_to_cpu(int node);
+
+/* Init this module early */
+extern void cbe_regs_init(void);
+
+
+#endif /* CBE_REGS_H */
diff --git a/include/asm-powerpc/clk_interface.h b/include/asm-powerpc/clk_interface.h
new file mode 100644
index 000000000000..ab1882c1e176
--- /dev/null
+++ b/include/asm-powerpc/clk_interface.h
@@ -0,0 +1,20 @@
+#ifndef __ASM_POWERPC_CLK_INTERFACE_H
+#define __ASM_POWERPC_CLK_INTERFACE_H
+
+#include <linux/clk.h>
+
+struct clk_interface {
+	struct clk*	(*clk_get)	(struct device *dev, const char *id);
+	int		(*clk_enable)	(struct clk *clk);
+	void		(*clk_disable)	(struct clk *clk);
+	unsigned long	(*clk_get_rate)	(struct clk *clk);
+	void		(*clk_put)	(struct clk *clk);
+	long		(*clk_round_rate) (struct clk *clk, unsigned long rate);
+	int 		(*clk_set_rate)	(struct clk *clk, unsigned long rate);
+	int		(*clk_set_parent) (struct clk *clk, struct clk *parent);
+	struct clk*	(*clk_get_parent) (struct clk *clk);
+};
+
+extern struct clk_interface clk_functions;
+
+#endif /* __ASM_POWERPC_CLK_INTERFACE_H */
diff --git a/include/asm-powerpc/commproc.h b/include/asm-powerpc/commproc.h
new file mode 100644
index 000000000000..0307c84a5c1d
--- /dev/null
+++ b/include/asm-powerpc/commproc.h
@@ -0,0 +1,755 @@
+/*
+ * MPC8xx Communication Processor Module.
+ * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
+ *
+ * This file contains structures and information for the communication
+ * processor channels.  Some CPM control and status is available
+ * throught the MPC8xx internal memory map.  See immap.h for details.
+ * This file only contains what I need for the moment, not the total
+ * CPM capabilities.  I (or someone else) will add definitions as they
+ * are needed.  -- Dan
+ *
+ * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
+ * bytes of the DP RAM and relocates the I2C parameter area to the
+ * IDMA1 space.  The remaining DP RAM is available for buffer descriptors
+ * or other use.
+ */
+#ifndef __CPM_8XX__
+#define __CPM_8XX__
+
+#include <asm/8xx_immap.h>
+#include <asm/ptrace.h>
+#include <asm/cpm.h>
+
+/* CPM Command register.
+*/
+#define CPM_CR_RST	((ushort)0x8000)
+#define CPM_CR_OPCODE	((ushort)0x0f00)
+#define CPM_CR_CHAN	((ushort)0x00f0)
+#define CPM_CR_FLG	((ushort)0x0001)
+
+/* Some commands (there are more...later)
+*/
+#define CPM_CR_INIT_TRX		((ushort)0x0000)
+#define CPM_CR_INIT_RX		((ushort)0x0001)
+#define CPM_CR_INIT_TX		((ushort)0x0002)
+#define CPM_CR_HUNT_MODE	((ushort)0x0003)
+#define CPM_CR_STOP_TX		((ushort)0x0004)
+#define CPM_CR_GRA_STOP_TX	((ushort)0x0005)
+#define CPM_CR_RESTART_TX	((ushort)0x0006)
+#define CPM_CR_CLOSE_RX_BD	((ushort)0x0007)
+#define CPM_CR_SET_GADDR	((ushort)0x0008)
+#define CPM_CR_SET_TIMER	CPM_CR_SET_GADDR
+
+/* Channel numbers.
+*/
+#define CPM_CR_CH_SCC1		((ushort)0x0000)
+#define CPM_CR_CH_I2C		((ushort)0x0001)	/* I2C and IDMA1 */
+#define CPM_CR_CH_SCC2		((ushort)0x0004)
+#define CPM_CR_CH_SPI		((ushort)0x0005)	/* SPI / IDMA2 / Timers */
+#define CPM_CR_CH_TIMER		CPM_CR_CH_SPI
+#define CPM_CR_CH_SCC3		((ushort)0x0008)
+#define CPM_CR_CH_SMC1		((ushort)0x0009)	/* SMC1 / DSP1 */
+#define CPM_CR_CH_SCC4		((ushort)0x000c)
+#define CPM_CR_CH_SMC2		((ushort)0x000d)	/* SMC2 / DSP2 */
+
+#define mk_cr_cmd(CH, CMD)	((CMD << 8) | (CH << 4))
+
+#ifndef CONFIG_PPC_CPM_NEW_BINDING
+/* The dual ported RAM is multi-functional.  Some areas can be (and are
+ * being) used for microcode.  There is an area that can only be used
+ * as data ram for buffer descriptors, which is all we use right now.
+ * Currently the first 512 and last 256 bytes are used for microcode.
+ */
+#define CPM_DATAONLY_BASE	((uint)0x0800)
+#define CPM_DATAONLY_SIZE	((uint)0x0700)
+#define CPM_DP_NOSPACE		((uint)0x7fffffff)
+#endif
+
+/* Export the base address of the communication processor registers
+ * and dual port ram.
+ */
+extern cpm8xx_t __iomem *cpmp; /* Pointer to comm processor */
+
+#ifdef CONFIG_PPC_CPM_NEW_BINDING
+#define cpm_dpalloc cpm_muram_alloc
+#define cpm_dpfree cpm_muram_free
+#define cpm_dpram_addr cpm_muram_addr
+#define cpm_dpram_phys cpm_muram_dma
+#else
+extern unsigned long cpm_dpalloc(uint size, uint align);
+extern int cpm_dpfree(unsigned long offset);
+extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
+extern void cpm_dpdump(void);
+extern void *cpm_dpram_addr(unsigned long offset);
+extern uint cpm_dpram_phys(u8* addr);
+#endif
+
+extern void cpm_setbrg(uint brg, uint rate);
+
+extern uint m8xx_cpm_hostalloc(uint size);
+extern int  m8xx_cpm_hostfree(uint start);
+extern void m8xx_cpm_hostdump(void);
+
+extern void cpm_load_patch(volatile immap_t *immr);
+
+/* Buffer descriptors used by many of the CPM protocols.
+*/
+typedef struct cpm_buf_desc {
+	ushort	cbd_sc;		/* Status and Control */
+	ushort	cbd_datlen;	/* Data length in buffer */
+	uint	cbd_bufaddr;	/* Buffer address in host memory */
+} cbd_t;
+
+#define BD_SC_EMPTY	((ushort)0x8000)	/* Receive is empty */
+#define BD_SC_READY	((ushort)0x8000)	/* Transmit is ready */
+#define BD_SC_WRAP	((ushort)0x2000)	/* Last buffer descriptor */
+#define BD_SC_INTRPT	((ushort)0x1000)	/* Interrupt on change */
+#define BD_SC_LAST	((ushort)0x0800)	/* Last buffer in frame */
+#define BD_SC_TC	((ushort)0x0400)	/* Transmit CRC */
+#define BD_SC_CM	((ushort)0x0200)	/* Continous mode */
+#define BD_SC_ID	((ushort)0x0100)	/* Rec'd too many idles */
+#define BD_SC_P		((ushort)0x0100)	/* xmt preamble */
+#define BD_SC_BR	((ushort)0x0020)	/* Break received */
+#define BD_SC_FR	((ushort)0x0010)	/* Framing error */
+#define BD_SC_PR	((ushort)0x0008)	/* Parity error */
+#define BD_SC_NAK	((ushort)0x0004)	/* NAK - did not respond */
+#define BD_SC_OV	((ushort)0x0002)	/* Overrun */
+#define BD_SC_UN	((ushort)0x0002)	/* Underrun */
+#define BD_SC_CD	((ushort)0x0001)	/* ?? */
+#define BD_SC_CL	((ushort)0x0001)	/* Collision */
+
+/* Parameter RAM offsets.
+*/
+#define PROFF_SCC1	((uint)0x0000)
+#define PROFF_IIC	((uint)0x0080)
+#define PROFF_SCC2	((uint)0x0100)
+#define PROFF_SPI	((uint)0x0180)
+#define PROFF_SCC3	((uint)0x0200)
+#define PROFF_SMC1	((uint)0x0280)
+#define PROFF_SCC4	((uint)0x0300)
+#define PROFF_SMC2	((uint)0x0380)
+
+/* Define enough so I can at least use the serial port as a UART.
+ * The MBX uses SMC1 as the host serial port.
+ */
+typedef struct smc_uart {
+	ushort	smc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	smc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	smc_rfcr;	/* Rx function code */
+	u_char	smc_tfcr;	/* Tx function code */
+	ushort	smc_mrblr;	/* Max receive buffer length */
+	uint	smc_rstate;	/* Internal */
+	uint	smc_idp;	/* Internal */
+	ushort	smc_rbptr;	/* Internal */
+	ushort	smc_ibc;	/* Internal */
+	uint	smc_rxtmp;	/* Internal */
+	uint	smc_tstate;	/* Internal */
+	uint	smc_tdp;	/* Internal */
+	ushort	smc_tbptr;	/* Internal */
+	ushort	smc_tbc;	/* Internal */
+	uint	smc_txtmp;	/* Internal */
+	ushort	smc_maxidl;	/* Maximum idle characters */
+	ushort	smc_tmpidl;	/* Temporary idle counter */
+	ushort	smc_brklen;	/* Last received break length */
+	ushort	smc_brkec;	/* rcv'd break condition counter */
+	ushort	smc_brkcr;	/* xmt break count register */
+	ushort	smc_rmask;	/* Temporary bit mask */
+	char	res1[8];	/* Reserved */
+	ushort	smc_rpbase;	/* Relocation pointer */
+} smc_uart_t;
+
+/* Function code bits.
+*/
+#define SMC_EB	((u_char)0x10)	/* Set big endian byte order */
+
+/* SMC uart mode register.
+*/
+#define	SMCMR_REN	((ushort)0x0001)
+#define SMCMR_TEN	((ushort)0x0002)
+#define SMCMR_DM	((ushort)0x000c)
+#define SMCMR_SM_GCI	((ushort)0x0000)
+#define SMCMR_SM_UART	((ushort)0x0020)
+#define SMCMR_SM_TRANS	((ushort)0x0030)
+#define SMCMR_SM_MASK	((ushort)0x0030)
+#define SMCMR_PM_EVEN	((ushort)0x0100)	/* Even parity, else odd */
+#define SMCMR_REVD	SMCMR_PM_EVEN
+#define SMCMR_PEN	((ushort)0x0200)	/* Parity enable */
+#define SMCMR_BS	SMCMR_PEN
+#define SMCMR_SL	((ushort)0x0400)	/* Two stops, else one */
+#define SMCR_CLEN_MASK	((ushort)0x7800)	/* Character length */
+#define smcr_mk_clen(C)	(((C) << 11) & SMCR_CLEN_MASK)
+
+/* SMC2 as Centronics parallel printer.  It is half duplex, in that
+ * it can only receive or transmit.  The parameter ram values for
+ * each direction are either unique or properly overlap, so we can
+ * include them in one structure.
+ */
+typedef struct smc_centronics {
+	ushort	scent_rbase;
+	ushort	scent_tbase;
+	u_char	scent_cfcr;
+	u_char	scent_smask;
+	ushort	scent_mrblr;
+	uint	scent_rstate;
+	uint	scent_r_ptr;
+	ushort	scent_rbptr;
+	ushort	scent_r_cnt;
+	uint	scent_rtemp;
+	uint	scent_tstate;
+	uint	scent_t_ptr;
+	ushort	scent_tbptr;
+	ushort	scent_t_cnt;
+	uint	scent_ttemp;
+	ushort	scent_max_sl;
+	ushort	scent_sl_cnt;
+	ushort	scent_character1;
+	ushort	scent_character2;
+	ushort	scent_character3;
+	ushort	scent_character4;
+	ushort	scent_character5;
+	ushort	scent_character6;
+	ushort	scent_character7;
+	ushort	scent_character8;
+	ushort	scent_rccm;
+	ushort	scent_rccr;
+} smc_cent_t;
+
+/* Centronics Status Mask Register.
+*/
+#define SMC_CENT_F	((u_char)0x08)
+#define SMC_CENT_PE	((u_char)0x04)
+#define SMC_CENT_S	((u_char)0x02)
+
+/* SMC Event and Mask register.
+*/
+#define	SMCM_BRKE	((unsigned char)0x40)	/* When in UART Mode */
+#define	SMCM_BRK	((unsigned char)0x10)	/* When in UART Mode */
+#define	SMCM_TXE	((unsigned char)0x10)	/* When in Transparent Mode */
+#define	SMCM_BSY	((unsigned char)0x04)
+#define	SMCM_TX		((unsigned char)0x02)
+#define	SMCM_RX		((unsigned char)0x01)
+
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST		((uint)0x00020000)
+#define CPM_BRG_EN		((uint)0x00010000)
+#define CPM_BRG_EXTC_INT	((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK2	((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK6	((uint)0x00008000)
+#define CPM_BRG_ATB		((uint)0x00002000)
+#define CPM_BRG_CD_MASK		((uint)0x00001ffe)
+#define CPM_BRG_DIV16		((uint)0x00000001)
+
+/* SI Clock Route Register
+*/
+#define SICR_RCLK_SCC1_BRG1	((uint)0x00000000)
+#define SICR_TCLK_SCC1_BRG1	((uint)0x00000000)
+#define SICR_RCLK_SCC2_BRG2	((uint)0x00000800)
+#define SICR_TCLK_SCC2_BRG2	((uint)0x00000100)
+#define SICR_RCLK_SCC3_BRG3	((uint)0x00100000)
+#define SICR_TCLK_SCC3_BRG3	((uint)0x00020000)
+#define SICR_RCLK_SCC4_BRG4	((uint)0x18000000)
+#define SICR_TCLK_SCC4_BRG4	((uint)0x03000000)
+
+/* SCCs.
+*/
+#define SCC_GSMRH_IRP		((uint)0x00040000)
+#define SCC_GSMRH_GDE		((uint)0x00010000)
+#define SCC_GSMRH_TCRC_CCITT	((uint)0x00008000)
+#define SCC_GSMRH_TCRC_BISYNC	((uint)0x00004000)
+#define SCC_GSMRH_TCRC_HDLC	((uint)0x00000000)
+#define SCC_GSMRH_REVD		((uint)0x00002000)
+#define SCC_GSMRH_TRX		((uint)0x00001000)
+#define SCC_GSMRH_TTX		((uint)0x00000800)
+#define SCC_GSMRH_CDP		((uint)0x00000400)
+#define SCC_GSMRH_CTSP		((uint)0x00000200)
+#define SCC_GSMRH_CDS		((uint)0x00000100)
+#define SCC_GSMRH_CTSS		((uint)0x00000080)
+#define SCC_GSMRH_TFL		((uint)0x00000040)
+#define SCC_GSMRH_RFW		((uint)0x00000020)
+#define SCC_GSMRH_TXSY		((uint)0x00000010)
+#define SCC_GSMRH_SYNL16	((uint)0x0000000c)
+#define SCC_GSMRH_SYNL8		((uint)0x00000008)
+#define SCC_GSMRH_SYNL4		((uint)0x00000004)
+#define SCC_GSMRH_RTSM		((uint)0x00000002)
+#define SCC_GSMRH_RSYN		((uint)0x00000001)
+
+#define SCC_GSMRL_SIR		((uint)0x80000000)	/* SCC2 only */
+#define SCC_GSMRL_EDGE_NONE	((uint)0x60000000)
+#define SCC_GSMRL_EDGE_NEG	((uint)0x40000000)
+#define SCC_GSMRL_EDGE_POS	((uint)0x20000000)
+#define SCC_GSMRL_EDGE_BOTH	((uint)0x00000000)
+#define SCC_GSMRL_TCI		((uint)0x10000000)
+#define SCC_GSMRL_TSNC_3	((uint)0x0c000000)
+#define SCC_GSMRL_TSNC_4	((uint)0x08000000)
+#define SCC_GSMRL_TSNC_14	((uint)0x04000000)
+#define SCC_GSMRL_TSNC_INF	((uint)0x00000000)
+#define SCC_GSMRL_RINV		((uint)0x02000000)
+#define SCC_GSMRL_TINV		((uint)0x01000000)
+#define SCC_GSMRL_TPL_128	((uint)0x00c00000)
+#define SCC_GSMRL_TPL_64	((uint)0x00a00000)
+#define SCC_GSMRL_TPL_48	((uint)0x00800000)
+#define SCC_GSMRL_TPL_32	((uint)0x00600000)
+#define SCC_GSMRL_TPL_16	((uint)0x00400000)
+#define SCC_GSMRL_TPL_8		((uint)0x00200000)
+#define SCC_GSMRL_TPL_NONE	((uint)0x00000000)
+#define SCC_GSMRL_TPP_ALL1	((uint)0x00180000)
+#define SCC_GSMRL_TPP_01	((uint)0x00100000)
+#define SCC_GSMRL_TPP_10	((uint)0x00080000)
+#define SCC_GSMRL_TPP_ZEROS	((uint)0x00000000)
+#define SCC_GSMRL_TEND		((uint)0x00040000)
+#define SCC_GSMRL_TDCR_32	((uint)0x00030000)
+#define SCC_GSMRL_TDCR_16	((uint)0x00020000)
+#define SCC_GSMRL_TDCR_8	((uint)0x00010000)
+#define SCC_GSMRL_TDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RDCR_32	((uint)0x0000c000)
+#define SCC_GSMRL_RDCR_16	((uint)0x00008000)
+#define SCC_GSMRL_RDCR_8	((uint)0x00004000)
+#define SCC_GSMRL_RDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RENC_DFMAN	((uint)0x00003000)
+#define SCC_GSMRL_RENC_MANCH	((uint)0x00002000)
+#define SCC_GSMRL_RENC_FM0	((uint)0x00001000)
+#define SCC_GSMRL_RENC_NRZI	((uint)0x00000800)
+#define SCC_GSMRL_RENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_TENC_DFMAN	((uint)0x00000600)
+#define SCC_GSMRL_TENC_MANCH	((uint)0x00000400)
+#define SCC_GSMRL_TENC_FM0	((uint)0x00000200)
+#define SCC_GSMRL_TENC_NRZI	((uint)0x00000100)
+#define SCC_GSMRL_TENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_DIAG_LE	((uint)0x000000c0)	/* Loop and echo */
+#define SCC_GSMRL_DIAG_ECHO	((uint)0x00000080)
+#define SCC_GSMRL_DIAG_LOOP	((uint)0x00000040)
+#define SCC_GSMRL_DIAG_NORM	((uint)0x00000000)
+#define SCC_GSMRL_ENR		((uint)0x00000020)
+#define SCC_GSMRL_ENT		((uint)0x00000010)
+#define SCC_GSMRL_MODE_ENET	((uint)0x0000000c)
+#define SCC_GSMRL_MODE_QMC	((uint)0x0000000a)
+#define SCC_GSMRL_MODE_DDCMP	((uint)0x00000009)
+#define SCC_GSMRL_MODE_BISYNC	((uint)0x00000008)
+#define SCC_GSMRL_MODE_V14	((uint)0x00000007)
+#define SCC_GSMRL_MODE_AHDLC	((uint)0x00000006)
+#define SCC_GSMRL_MODE_PROFIBUS	((uint)0x00000005)
+#define SCC_GSMRL_MODE_UART	((uint)0x00000004)
+#define SCC_GSMRL_MODE_SS7	((uint)0x00000003)
+#define SCC_GSMRL_MODE_ATALK	((uint)0x00000002)
+#define SCC_GSMRL_MODE_HDLC	((uint)0x00000000)
+
+#define SCC_TODR_TOD		((ushort)0x8000)
+
+/* SCC Event and Mask register.
+*/
+#define	SCCM_TXE	((unsigned char)0x10)
+#define	SCCM_BSY	((unsigned char)0x04)
+#define	SCCM_TX		((unsigned char)0x02)
+#define	SCCM_RX		((unsigned char)0x01)
+
+typedef struct scc_param {
+	ushort	scc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	scc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	scc_rfcr;	/* Rx function code */
+	u_char	scc_tfcr;	/* Tx function code */
+	ushort	scc_mrblr;	/* Max receive buffer length */
+	uint	scc_rstate;	/* Internal */
+	uint	scc_idp;	/* Internal */
+	ushort	scc_rbptr;	/* Internal */
+	ushort	scc_ibc;	/* Internal */
+	uint	scc_rxtmp;	/* Internal */
+	uint	scc_tstate;	/* Internal */
+	uint	scc_tdp;	/* Internal */
+	ushort	scc_tbptr;	/* Internal */
+	ushort	scc_tbc;	/* Internal */
+	uint	scc_txtmp;	/* Internal */
+	uint	scc_rcrc;	/* Internal */
+	uint	scc_tcrc;	/* Internal */
+} sccp_t;
+
+/* Function code bits.
+*/
+#define SCC_EB	((u_char)0x10)	/* Set big endian byte order */
+
+/* CPM Ethernet through SCCx.
+ */
+typedef struct scc_enet {
+	sccp_t	sen_genscc;
+	uint	sen_cpres;	/* Preset CRC */
+	uint	sen_cmask;	/* Constant mask for CRC */
+	uint	sen_crcec;	/* CRC Error counter */
+	uint	sen_alec;	/* alignment error counter */
+	uint	sen_disfc;	/* discard frame counter */
+	ushort	sen_pads;	/* Tx short frame pad character */
+	ushort	sen_retlim;	/* Retry limit threshold */
+	ushort	sen_retcnt;	/* Retry limit counter */
+	ushort	sen_maxflr;	/* maximum frame length register */
+	ushort	sen_minflr;	/* minimum frame length register */
+	ushort	sen_maxd1;	/* maximum DMA1 length */
+	ushort	sen_maxd2;	/* maximum DMA2 length */
+	ushort	sen_maxd;	/* Rx max DMA */
+	ushort	sen_dmacnt;	/* Rx DMA counter */
+	ushort	sen_maxb;	/* Max BD byte count */
+	ushort	sen_gaddr1;	/* Group address filter */
+	ushort	sen_gaddr2;
+	ushort	sen_gaddr3;
+	ushort	sen_gaddr4;
+	uint	sen_tbuf0data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf0data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf0rba;	/* Internal */
+	uint	sen_tbuf0crc;	/* Internal */
+	ushort	sen_tbuf0bcnt;	/* Internal */
+	ushort	sen_paddrh;	/* physical address (MSB) */
+	ushort	sen_paddrm;
+	ushort	sen_paddrl;	/* physical address (LSB) */
+	ushort	sen_pper;	/* persistence */
+	ushort	sen_rfbdptr;	/* Rx first BD pointer */
+	ushort	sen_tfbdptr;	/* Tx first BD pointer */
+	ushort	sen_tlbdptr;	/* Tx last BD pointer */
+	uint	sen_tbuf1data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf1data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf1rba;	/* Internal */
+	uint	sen_tbuf1crc;	/* Internal */
+	ushort	sen_tbuf1bcnt;	/* Internal */
+	ushort	sen_txlen;	/* Tx Frame length counter */
+	ushort	sen_iaddr1;	/* Individual address filter */
+	ushort	sen_iaddr2;
+	ushort	sen_iaddr3;
+	ushort	sen_iaddr4;
+	ushort	sen_boffcnt;	/* Backoff counter */
+
+	/* NOTE: Some versions of the manual have the following items
+	 * incorrectly documented.  Below is the proper order.
+	 */
+	ushort	sen_taddrh;	/* temp address (MSB) */
+	ushort	sen_taddrm;
+	ushort	sen_taddrl;	/* temp address (LSB) */
+} scc_enet_t;
+
+/* SCC Event register as used by Ethernet.
+*/
+#define SCCE_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */
+#define SCCE_ENET_TXE	((ushort)0x0010)	/* Transmit Error */
+#define SCCE_ENET_RXF	((ushort)0x0008)	/* Full frame received */
+#define SCCE_ENET_BSY	((ushort)0x0004)	/* All incoming buffers full */
+#define SCCE_ENET_TXB	((ushort)0x0002)	/* A buffer was transmitted */
+#define SCCE_ENET_RXB	((ushort)0x0001)	/* A buffer was received */
+
+/* SCC Mode Register (PMSR) as used by Ethernet.
+*/
+#define SCC_PSMR_HBC	((ushort)0x8000)	/* Enable heartbeat */
+#define SCC_PSMR_FC	((ushort)0x4000)	/* Force collision */
+#define SCC_PSMR_RSH	((ushort)0x2000)	/* Receive short frames */
+#define SCC_PSMR_IAM	((ushort)0x1000)	/* Check individual hash */
+#define SCC_PSMR_ENCRC	((ushort)0x0800)	/* Ethernet CRC mode */
+#define SCC_PSMR_PRO	((ushort)0x0200)	/* Promiscuous mode */
+#define SCC_PSMR_BRO	((ushort)0x0100)	/* Catch broadcast pkts */
+#define SCC_PSMR_SBT	((ushort)0x0080)	/* Special backoff timer */
+#define SCC_PSMR_LPB	((ushort)0x0040)	/* Set Loopback mode */
+#define SCC_PSMR_SIP	((ushort)0x0020)	/* Sample Input Pins */
+#define SCC_PSMR_LCW	((ushort)0x0010)	/* Late collision window */
+#define SCC_PSMR_NIB22	((ushort)0x000a)	/* Start frame search */
+#define SCC_PSMR_FDE	((ushort)0x0001)	/* Full duplex enable */
+
+/* Buffer descriptor control/status used by Ethernet receive.
+*/
+#define BD_ENET_RX_EMPTY	((ushort)0x8000)
+#define BD_ENET_RX_WRAP		((ushort)0x2000)
+#define BD_ENET_RX_INTR		((ushort)0x1000)
+#define BD_ENET_RX_LAST		((ushort)0x0800)
+#define BD_ENET_RX_FIRST	((ushort)0x0400)
+#define BD_ENET_RX_MISS		((ushort)0x0100)
+#define BD_ENET_RX_LG		((ushort)0x0020)
+#define BD_ENET_RX_NO		((ushort)0x0010)
+#define BD_ENET_RX_SH		((ushort)0x0008)
+#define BD_ENET_RX_CR		((ushort)0x0004)
+#define BD_ENET_RX_OV		((ushort)0x0002)
+#define BD_ENET_RX_CL		((ushort)0x0001)
+#define BD_ENET_RX_BC		((ushort)0x0080)	/* DA is Broadcast */
+#define BD_ENET_RX_MC		((ushort)0x0040)	/* DA is Multicast */
+#define BD_ENET_RX_STATS	((ushort)0x013f)	/* All status bits */
+
+/* Buffer descriptor control/status used by Ethernet transmit.
+*/
+#define BD_ENET_TX_READY	((ushort)0x8000)
+#define BD_ENET_TX_PAD		((ushort)0x4000)
+#define BD_ENET_TX_WRAP		((ushort)0x2000)
+#define BD_ENET_TX_INTR		((ushort)0x1000)
+#define BD_ENET_TX_LAST		((ushort)0x0800)
+#define BD_ENET_TX_TC		((ushort)0x0400)
+#define BD_ENET_TX_DEF		((ushort)0x0200)
+#define BD_ENET_TX_HB		((ushort)0x0100)
+#define BD_ENET_TX_LC		((ushort)0x0080)
+#define BD_ENET_TX_RL		((ushort)0x0040)
+#define BD_ENET_TX_RCMASK	((ushort)0x003c)
+#define BD_ENET_TX_UN		((ushort)0x0002)
+#define BD_ENET_TX_CSL		((ushort)0x0001)
+#define BD_ENET_TX_STATS	((ushort)0x03ff)	/* All status bits */
+
+/* SCC as UART
+*/
+typedef struct scc_uart {
+	sccp_t	scc_genscc;
+	char	res1[8];	/* Reserved */
+	ushort	scc_maxidl;	/* Maximum idle chars */
+	ushort	scc_idlc;	/* temp idle counter */
+	ushort	scc_brkcr;	/* Break count register */
+	ushort	scc_parec;	/* receive parity error counter */
+	ushort	scc_frmec;	/* receive framing error counter */
+	ushort	scc_nosec;	/* receive noise counter */
+	ushort	scc_brkec;	/* receive break condition counter */
+	ushort	scc_brkln;	/* last received break length */
+	ushort	scc_uaddr1;	/* UART address character 1 */
+	ushort	scc_uaddr2;	/* UART address character 2 */
+	ushort	scc_rtemp;	/* Temp storage */
+	ushort	scc_toseq;	/* Transmit out of sequence char */
+	ushort	scc_char1;	/* control character 1 */
+	ushort	scc_char2;	/* control character 2 */
+	ushort	scc_char3;	/* control character 3 */
+	ushort	scc_char4;	/* control character 4 */
+	ushort	scc_char5;	/* control character 5 */
+	ushort	scc_char6;	/* control character 6 */
+	ushort	scc_char7;	/* control character 7 */
+	ushort	scc_char8;	/* control character 8 */
+	ushort	scc_rccm;	/* receive control character mask */
+	ushort	scc_rccr;	/* receive control character register */
+	ushort	scc_rlbc;	/* receive last break character */
+} scc_uart_t;
+
+/* SCC Event and Mask registers when it is used as a UART.
+*/
+#define UART_SCCM_GLR		((ushort)0x1000)
+#define UART_SCCM_GLT		((ushort)0x0800)
+#define UART_SCCM_AB		((ushort)0x0200)
+#define UART_SCCM_IDL		((ushort)0x0100)
+#define UART_SCCM_GRA		((ushort)0x0080)
+#define UART_SCCM_BRKE		((ushort)0x0040)
+#define UART_SCCM_BRKS		((ushort)0x0020)
+#define UART_SCCM_CCR		((ushort)0x0008)
+#define UART_SCCM_BSY		((ushort)0x0004)
+#define UART_SCCM_TX		((ushort)0x0002)
+#define UART_SCCM_RX		((ushort)0x0001)
+
+/* The SCC PMSR when used as a UART.
+*/
+#define SCU_PSMR_FLC		((ushort)0x8000)
+#define SCU_PSMR_SL		((ushort)0x4000)
+#define SCU_PSMR_CL		((ushort)0x3000)
+#define SCU_PSMR_UM		((ushort)0x0c00)
+#define SCU_PSMR_FRZ		((ushort)0x0200)
+#define SCU_PSMR_RZS		((ushort)0x0100)
+#define SCU_PSMR_SYN		((ushort)0x0080)
+#define SCU_PSMR_DRT		((ushort)0x0040)
+#define SCU_PSMR_PEN		((ushort)0x0010)
+#define SCU_PSMR_RPM		((ushort)0x000c)
+#define SCU_PSMR_REVP		((ushort)0x0008)
+#define SCU_PSMR_TPM		((ushort)0x0003)
+#define SCU_PSMR_TEVP		((ushort)0x0002)
+
+/* CPM Transparent mode SCC.
+ */
+typedef struct scc_trans {
+	sccp_t	st_genscc;
+	uint	st_cpres;	/* Preset CRC */
+	uint	st_cmask;	/* Constant mask for CRC */
+} scc_trans_t;
+
+#define BD_SCC_TX_LAST		((ushort)0x0800)
+
+/* IIC parameter RAM.
+*/
+typedef struct iic {
+	ushort	iic_rbase;	/* Rx Buffer descriptor base address */
+	ushort	iic_tbase;	/* Tx Buffer descriptor base address */
+	u_char	iic_rfcr;	/* Rx function code */
+	u_char	iic_tfcr;	/* Tx function code */
+	ushort	iic_mrblr;	/* Max receive buffer length */
+	uint	iic_rstate;	/* Internal */
+	uint	iic_rdp;	/* Internal */
+	ushort	iic_rbptr;	/* Internal */
+	ushort	iic_rbc;	/* Internal */
+	uint	iic_rxtmp;	/* Internal */
+	uint	iic_tstate;	/* Internal */
+	uint	iic_tdp;	/* Internal */
+	ushort	iic_tbptr;	/* Internal */
+	ushort	iic_tbc;	/* Internal */
+	uint	iic_txtmp;	/* Internal */
+	char	res1[4];	/* Reserved */
+	ushort	iic_rpbase;	/* Relocation pointer */
+	char	res2[2];	/* Reserved */
+} iic_t;
+
+#define BD_IIC_START		((ushort)0x0400)
+
+/* SPI parameter RAM.
+*/
+typedef struct spi {
+	ushort	spi_rbase;	/* Rx Buffer descriptor base address */
+	ushort	spi_tbase;	/* Tx Buffer descriptor base address */
+	u_char	spi_rfcr;	/* Rx function code */
+	u_char	spi_tfcr;	/* Tx function code */
+	ushort	spi_mrblr;	/* Max receive buffer length */
+	uint	spi_rstate;	/* Internal */
+	uint	spi_rdp;	/* Internal */
+	ushort	spi_rbptr;	/* Internal */
+	ushort	spi_rbc;	/* Internal */
+	uint	spi_rxtmp;	/* Internal */
+	uint	spi_tstate;	/* Internal */
+	uint	spi_tdp;	/* Internal */
+	ushort	spi_tbptr;	/* Internal */
+	ushort	spi_tbc;	/* Internal */
+	uint	spi_txtmp;	/* Internal */
+	uint	spi_res;
+	ushort	spi_rpbase;	/* Relocation pointer */
+	ushort	spi_res2;
+} spi_t;
+
+/* SPI Mode register.
+*/
+#define SPMODE_LOOP	((ushort)0x4000)	/* Loopback */
+#define SPMODE_CI	((ushort)0x2000)	/* Clock Invert */
+#define SPMODE_CP	((ushort)0x1000)	/* Clock Phase */
+#define SPMODE_DIV16	((ushort)0x0800)	/* BRG/16 mode */
+#define SPMODE_REV	((ushort)0x0400)	/* Reversed Data */
+#define SPMODE_MSTR	((ushort)0x0200)	/* SPI Master */
+#define SPMODE_EN	((ushort)0x0100)	/* Enable */
+#define SPMODE_LENMSK	((ushort)0x00f0)	/* character length */
+#define SPMODE_LEN4	((ushort)0x0030)	/*  4 bits per char */
+#define SPMODE_LEN8	((ushort)0x0070)	/*  8 bits per char */
+#define SPMODE_LEN16	((ushort)0x00f0)	/* 16 bits per char */
+#define SPMODE_PMMSK	((ushort)0x000f)	/* prescale modulus */
+
+/* SPIE fields */
+#define SPIE_MME	0x20
+#define SPIE_TXE	0x10
+#define SPIE_BSY	0x04
+#define SPIE_TXB	0x02
+#define SPIE_RXB	0x01
+
+/*
+ * RISC Controller Configuration Register definitons
+ */
+#define RCCR_TIME	0x8000			/* RISC Timer Enable */
+#define RCCR_TIMEP(t)	(((t) & 0x3F)<<8)	/* RISC Timer Period */
+#define RCCR_TIME_MASK	0x00FF			/* not RISC Timer related bits */
+
+/* RISC Timer Parameter RAM offset */
+#define PROFF_RTMR	((uint)0x01B0)
+
+typedef struct risc_timer_pram {
+	unsigned short	tm_base;	/* RISC Timer Table Base Address */
+	unsigned short	tm_ptr;		/* RISC Timer Table Pointer (internal) */
+	unsigned short	r_tmr;		/* RISC Timer Mode Register */
+	unsigned short	r_tmv;		/* RISC Timer Valid Register */
+	unsigned long	tm_cmd;		/* RISC Timer Command Register */
+	unsigned long	tm_cnt;		/* RISC Timer Internal Count */
+} rt_pram_t;
+
+/* Bits in RISC Timer Command Register */
+#define TM_CMD_VALID	0x80000000	/* Valid - Enables the timer */
+#define TM_CMD_RESTART	0x40000000	/* Restart - for automatic restart */
+#define TM_CMD_PWM	0x20000000	/* Run in Pulse Width Modulation Mode */
+#define TM_CMD_NUM(n)	(((n)&0xF)<<16)	/* Timer Number */
+#define TM_CMD_PERIOD(p) ((p)&0xFFFF)	/* Timer Period */
+
+/* CPM interrupts.  There are nearly 32 interrupts generated by CPM
+ * channels or devices.  All of these are presented to the PPC core
+ * as a single interrupt.  The CPM interrupt handler dispatches its
+ * own handlers, in a similar fashion to the PPC core handler.  We
+ * use the table as defined in the manuals (i.e. no special high
+ * priority and SCC1 == SCCa, etc...).
+ */
+#define CPMVEC_NR		32
+#define	CPMVEC_PIO_PC15		((ushort)0x1f)
+#define	CPMVEC_SCC1		((ushort)0x1e)
+#define	CPMVEC_SCC2		((ushort)0x1d)
+#define	CPMVEC_SCC3		((ushort)0x1c)
+#define	CPMVEC_SCC4		((ushort)0x1b)
+#define	CPMVEC_PIO_PC14		((ushort)0x1a)
+#define	CPMVEC_TIMER1		((ushort)0x19)
+#define	CPMVEC_PIO_PC13		((ushort)0x18)
+#define	CPMVEC_PIO_PC12		((ushort)0x17)
+#define	CPMVEC_SDMA_CB_ERR	((ushort)0x16)
+#define CPMVEC_IDMA1		((ushort)0x15)
+#define CPMVEC_IDMA2		((ushort)0x14)
+#define CPMVEC_TIMER2		((ushort)0x12)
+#define CPMVEC_RISCTIMER	((ushort)0x11)
+#define CPMVEC_I2C		((ushort)0x10)
+#define	CPMVEC_PIO_PC11		((ushort)0x0f)
+#define	CPMVEC_PIO_PC10		((ushort)0x0e)
+#define CPMVEC_TIMER3		((ushort)0x0c)
+#define	CPMVEC_PIO_PC9		((ushort)0x0b)
+#define	CPMVEC_PIO_PC8		((ushort)0x0a)
+#define	CPMVEC_PIO_PC7		((ushort)0x09)
+#define CPMVEC_TIMER4		((ushort)0x07)
+#define	CPMVEC_PIO_PC6		((ushort)0x06)
+#define	CPMVEC_SPI		((ushort)0x05)
+#define	CPMVEC_SMC1		((ushort)0x04)
+#define	CPMVEC_SMC2		((ushort)0x03)
+#define	CPMVEC_PIO_PC5		((ushort)0x02)
+#define	CPMVEC_PIO_PC4		((ushort)0x01)
+#define	CPMVEC_ERROR		((ushort)0x00)
+
+/* CPM interrupt configuration vector.
+*/
+#define	CICR_SCD_SCC4		((uint)0x00c00000)	/* SCC4 @ SCCd */
+#define	CICR_SCC_SCC3		((uint)0x00200000)	/* SCC3 @ SCCc */
+#define	CICR_SCB_SCC2		((uint)0x00040000)	/* SCC2 @ SCCb */
+#define	CICR_SCA_SCC1		((uint)0x00000000)	/* SCC1 @ SCCa */
+#define CICR_IRL_MASK		((uint)0x0000e000)	/* Core interrrupt */
+#define CICR_HP_MASK		((uint)0x00001f00)	/* Hi-pri int. */
+#define CICR_IEN		((uint)0x00000080)	/* Int. enable */
+#define CICR_SPS		((uint)0x00000001)	/* SCC Spread */
+
+extern void cpm_install_handler(int vec, void (*handler)(void *), void *dev_id);
+extern void cpm_free_handler(int vec);
+
+#define IMAP_ADDR		(get_immrbase())
+
+#define CPM_PIN_INPUT     0
+#define CPM_PIN_OUTPUT    1
+#define CPM_PIN_PRIMARY   0
+#define CPM_PIN_SECONDARY 2
+#define CPM_PIN_GPIO      4
+#define CPM_PIN_OPENDRAIN 8
+
+enum cpm_port {
+	CPM_PORTA,
+	CPM_PORTB,
+	CPM_PORTC,
+	CPM_PORTD,
+	CPM_PORTE,
+};
+
+void cpm1_set_pin(enum cpm_port port, int pin, int flags);
+
+enum cpm_clk_dir {
+	CPM_CLK_RX,
+	CPM_CLK_TX,
+	CPM_CLK_RTX
+};
+
+enum cpm_clk_target {
+	CPM_CLK_SCC1,
+	CPM_CLK_SCC2,
+	CPM_CLK_SCC3,
+	CPM_CLK_SCC4,
+	CPM_CLK_SMC1,
+	CPM_CLK_SMC2,
+};
+
+enum cpm_clk {
+	CPM_BRG1,	/* Baud Rate Generator  1 */
+	CPM_BRG2,	/* Baud Rate Generator  2 */
+	CPM_BRG3,	/* Baud Rate Generator  3 */
+	CPM_BRG4,	/* Baud Rate Generator  4 */
+	CPM_CLK1,	/* Clock  1 */
+	CPM_CLK2,	/* Clock  2 */
+	CPM_CLK3,	/* Clock  3 */
+	CPM_CLK4,	/* Clock  4 */
+	CPM_CLK5,	/* Clock  5 */
+	CPM_CLK6,	/* Clock  6 */
+	CPM_CLK7,	/* Clock  7 */
+	CPM_CLK8,	/* Clock  8 */
+};
+
+int cpm1_clk_setup(enum cpm_clk_target target, int clock, int mode);
+
+#endif /* __CPM_8XX__ */
diff --git a/include/asm-powerpc/cpm.h b/include/asm-powerpc/cpm.h
new file mode 100644
index 000000000000..48df9f330e76
--- /dev/null
+++ b/include/asm-powerpc/cpm.h
@@ -0,0 +1,14 @@
+#ifndef __CPM_H
+#define __CPM_H
+
+#include <linux/compiler.h>
+#include <linux/types.h>
+
+int cpm_muram_init(void);
+unsigned long cpm_muram_alloc(unsigned long size, unsigned long align);
+int cpm_muram_free(unsigned long offset);
+unsigned long cpm_muram_alloc_fixed(unsigned long offset, unsigned long size);
+void __iomem *cpm_muram_addr(unsigned long offset);
+dma_addr_t cpm_muram_dma(void __iomem *addr);
+
+#endif
diff --git a/include/asm-powerpc/cpm2.h b/include/asm-powerpc/cpm2.h
new file mode 100644
index 000000000000..f1112c15ef96
--- /dev/null
+++ b/include/asm-powerpc/cpm2.h
@@ -0,0 +1,1274 @@
+/*
+ * Communication Processor Module v2.
+ *
+ * This file contains structures and information for the communication
+ * processor channels found in the dual port RAM or parameter RAM.
+ * All CPM control and status is available through the CPM2 internal
+ * memory map.  See immap_cpm2.h for details.
+ */
+#ifdef __KERNEL__
+#ifndef __CPM2__
+#define __CPM2__
+
+#include <asm/immap_cpm2.h>
+#include <asm/cpm.h>
+
+#ifdef CONFIG_PPC_85xx
+#define CPM_MAP_ADDR (get_immrbase() + 0x80000)
+#endif
+
+/* CPM Command register.
+*/
+#define CPM_CR_RST	((uint)0x80000000)
+#define CPM_CR_PAGE	((uint)0x7c000000)
+#define CPM_CR_SBLOCK	((uint)0x03e00000)
+#define CPM_CR_FLG	((uint)0x00010000)
+#define CPM_CR_MCN	((uint)0x00003fc0)
+#define CPM_CR_OPCODE	((uint)0x0000000f)
+
+/* Device sub-block and page codes.
+*/
+#define CPM_CR_SCC1_SBLOCK	(0x04)
+#define CPM_CR_SCC2_SBLOCK	(0x05)
+#define CPM_CR_SCC3_SBLOCK	(0x06)
+#define CPM_CR_SCC4_SBLOCK	(0x07)
+#define CPM_CR_SMC1_SBLOCK	(0x08)
+#define CPM_CR_SMC2_SBLOCK	(0x09)
+#define CPM_CR_SPI_SBLOCK	(0x0a)
+#define CPM_CR_I2C_SBLOCK	(0x0b)
+#define CPM_CR_TIMER_SBLOCK	(0x0f)
+#define CPM_CR_RAND_SBLOCK	(0x0e)
+#define CPM_CR_FCC1_SBLOCK	(0x10)
+#define CPM_CR_FCC2_SBLOCK	(0x11)
+#define CPM_CR_FCC3_SBLOCK	(0x12)
+#define CPM_CR_IDMA1_SBLOCK	(0x14)
+#define CPM_CR_IDMA2_SBLOCK	(0x15)
+#define CPM_CR_IDMA3_SBLOCK	(0x16)
+#define CPM_CR_IDMA4_SBLOCK	(0x17)
+#define CPM_CR_MCC1_SBLOCK	(0x1c)
+
+#define CPM_CR_FCC_SBLOCK(x)	(x + 0x10)
+
+#define CPM_CR_SCC1_PAGE	(0x00)
+#define CPM_CR_SCC2_PAGE	(0x01)
+#define CPM_CR_SCC3_PAGE	(0x02)
+#define CPM_CR_SCC4_PAGE	(0x03)
+#define CPM_CR_SMC1_PAGE	(0x07)
+#define CPM_CR_SMC2_PAGE	(0x08)
+#define CPM_CR_SPI_PAGE		(0x09)
+#define CPM_CR_I2C_PAGE		(0x0a)
+#define CPM_CR_TIMER_PAGE	(0x0a)
+#define CPM_CR_RAND_PAGE	(0x0a)
+#define CPM_CR_FCC1_PAGE	(0x04)
+#define CPM_CR_FCC2_PAGE	(0x05)
+#define CPM_CR_FCC3_PAGE	(0x06)
+#define CPM_CR_IDMA1_PAGE	(0x07)
+#define CPM_CR_IDMA2_PAGE	(0x08)
+#define CPM_CR_IDMA3_PAGE	(0x09)
+#define CPM_CR_IDMA4_PAGE	(0x0a)
+#define CPM_CR_MCC1_PAGE	(0x07)
+#define CPM_CR_MCC2_PAGE	(0x08)
+
+#define CPM_CR_FCC_PAGE(x)	(x + 0x04)
+
+/* Some opcodes (there are more...later)
+*/
+#define CPM_CR_INIT_TRX		((ushort)0x0000)
+#define CPM_CR_INIT_RX		((ushort)0x0001)
+#define CPM_CR_INIT_TX		((ushort)0x0002)
+#define CPM_CR_HUNT_MODE	((ushort)0x0003)
+#define CPM_CR_STOP_TX		((ushort)0x0004)
+#define CPM_CR_GRA_STOP_TX	((ushort)0x0005)
+#define CPM_CR_RESTART_TX	((ushort)0x0006)
+#define CPM_CR_SET_GADDR	((ushort)0x0008)
+#define CPM_CR_START_IDMA	((ushort)0x0009)
+#define CPM_CR_STOP_IDMA	((ushort)0x000b)
+
+#define mk_cr_cmd(PG, SBC, MCN, OP) \
+	((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
+
+#ifndef CONFIG_PPC_CPM_NEW_BINDING
+/* Dual Port RAM addresses.  The first 16K is available for almost
+ * any CPM use, so we put the BDs there.  The first 128 bytes are
+ * used for SMC1 and SMC2 parameter RAM, so we start allocating
+ * BDs above that.  All of this must change when we start
+ * downloading RAM microcode.
+ */
+#define CPM_DATAONLY_BASE	((uint)128)
+#define CPM_DP_NOSPACE		((uint)0x7fffffff)
+#if defined(CONFIG_8272) || defined(CONFIG_MPC8555)
+#define CPM_DATAONLY_SIZE	((uint)(8 * 1024) - CPM_DATAONLY_BASE)
+#define CPM_FCC_SPECIAL_BASE	((uint)0x00009000)
+#else
+#define CPM_DATAONLY_SIZE	((uint)(16 * 1024) - CPM_DATAONLY_BASE)
+#define CPM_FCC_SPECIAL_BASE	((uint)0x0000b000)
+#endif
+#endif
+
+/* The number of pages of host memory we allocate for CPM.  This is
+ * done early in kernel initialization to get physically contiguous
+ * pages.
+ */
+#define NUM_CPM_HOST_PAGES	2
+
+/* Export the base address of the communication processor registers
+ * and dual port ram.
+ */
+extern cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor */
+
+#ifdef CONFIG_PPC_CPM_NEW_BINDING
+#define cpm_dpalloc cpm_muram_alloc
+#define cpm_dpfree cpm_muram_free
+#define cpm_dpram_addr cpm_muram_addr
+#else
+extern unsigned long cpm_dpalloc(uint size, uint align);
+extern int cpm_dpfree(unsigned long offset);
+extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
+extern void cpm_dpdump(void);
+extern void *cpm_dpram_addr(unsigned long offset);
+#endif
+
+extern void cpm_setbrg(uint brg, uint rate);
+extern void cpm2_fastbrg(uint brg, uint rate, int div16);
+extern void cpm2_reset(void);
+
+
+/* Buffer descriptors used by many of the CPM protocols.
+*/
+typedef struct cpm_buf_desc {
+	ushort	cbd_sc;		/* Status and Control */
+	ushort	cbd_datlen;	/* Data length in buffer */
+	uint	cbd_bufaddr;	/* Buffer address in host memory */
+} cbd_t;
+
+#define BD_SC_EMPTY	((ushort)0x8000)	/* Receive is empty */
+#define BD_SC_READY	((ushort)0x8000)	/* Transmit is ready */
+#define BD_SC_WRAP	((ushort)0x2000)	/* Last buffer descriptor */
+#define BD_SC_INTRPT	((ushort)0x1000)	/* Interrupt on change */
+#define BD_SC_LAST	((ushort)0x0800)	/* Last buffer in frame */
+#define BD_SC_CM	((ushort)0x0200)	/* Continous mode */
+#define BD_SC_ID	((ushort)0x0100)	/* Rec'd too many idles */
+#define BD_SC_P		((ushort)0x0100)	/* xmt preamble */
+#define BD_SC_BR	((ushort)0x0020)	/* Break received */
+#define BD_SC_FR	((ushort)0x0010)	/* Framing error */
+#define BD_SC_PR	((ushort)0x0008)	/* Parity error */
+#define BD_SC_OV	((ushort)0x0002)	/* Overrun */
+#define BD_SC_CD	((ushort)0x0001)	/* ?? */
+
+/* Function code bits, usually generic to devices.
+*/
+#define CPMFCR_GBL	((u_char)0x20)	/* Set memory snooping */
+#define CPMFCR_EB	((u_char)0x10)	/* Set big endian byte order */
+#define CPMFCR_TC2	((u_char)0x04)	/* Transfer code 2 value */
+#define CPMFCR_DTB	((u_char)0x02)	/* Use local bus for data when set */
+#define CPMFCR_BDB	((u_char)0x01)	/* Use local bus for BD when set */
+
+/* Parameter RAM offsets from the base.
+*/
+#define PROFF_SCC1		((uint)0x8000)
+#define PROFF_SCC2		((uint)0x8100)
+#define PROFF_SCC3		((uint)0x8200)
+#define PROFF_SCC4		((uint)0x8300)
+#define PROFF_FCC1		((uint)0x8400)
+#define PROFF_FCC2		((uint)0x8500)
+#define PROFF_FCC3		((uint)0x8600)
+#define PROFF_MCC1		((uint)0x8700)
+#define PROFF_SMC1_BASE		((uint)0x87fc)
+#define PROFF_IDMA1_BASE	((uint)0x87fe)
+#define PROFF_MCC2		((uint)0x8800)
+#define PROFF_SMC2_BASE		((uint)0x88fc)
+#define PROFF_IDMA2_BASE	((uint)0x88fe)
+#define PROFF_SPI_BASE		((uint)0x89fc)
+#define PROFF_IDMA3_BASE	((uint)0x89fe)
+#define PROFF_TIMERS		((uint)0x8ae0)
+#define PROFF_REVNUM		((uint)0x8af0)
+#define PROFF_RAND		((uint)0x8af8)
+#define PROFF_I2C_BASE		((uint)0x8afc)
+#define PROFF_IDMA4_BASE	((uint)0x8afe)
+
+#define PROFF_SCC_SIZE		((uint)0x100)
+#define PROFF_FCC_SIZE		((uint)0x100)
+#define PROFF_SMC_SIZE		((uint)64)
+
+/* The SMCs are relocated to any of the first eight DPRAM pages.
+ * We will fix these at the first locations of DPRAM, until we
+ * get some microcode patches :-).
+ * The parameter ram space for the SMCs is fifty-some bytes, and
+ * they are required to start on a 64 byte boundary.
+ */
+#define PROFF_SMC1	(0)
+#define PROFF_SMC2	(64)
+
+
+/* Define enough so I can at least use the serial port as a UART.
+ */
+typedef struct smc_uart {
+	ushort	smc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	smc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	smc_rfcr;	/* Rx function code */
+	u_char	smc_tfcr;	/* Tx function code */
+	ushort	smc_mrblr;	/* Max receive buffer length */
+	uint	smc_rstate;	/* Internal */
+	uint	smc_idp;	/* Internal */
+	ushort	smc_rbptr;	/* Internal */
+	ushort	smc_ibc;	/* Internal */
+	uint	smc_rxtmp;	/* Internal */
+	uint	smc_tstate;	/* Internal */
+	uint	smc_tdp;	/* Internal */
+	ushort	smc_tbptr;	/* Internal */
+	ushort	smc_tbc;	/* Internal */
+	uint	smc_txtmp;	/* Internal */
+	ushort	smc_maxidl;	/* Maximum idle characters */
+	ushort	smc_tmpidl;	/* Temporary idle counter */
+	ushort	smc_brklen;	/* Last received break length */
+	ushort	smc_brkec;	/* rcv'd break condition counter */
+	ushort	smc_brkcr;	/* xmt break count register */
+	ushort	smc_rmask;	/* Temporary bit mask */
+	uint	smc_stmp;	/* SDMA Temp */
+} smc_uart_t;
+
+/* SMC uart mode register (Internal memory map).
+*/
+#define SMCMR_REN	((ushort)0x0001)
+#define SMCMR_TEN	((ushort)0x0002)
+#define SMCMR_DM	((ushort)0x000c)
+#define SMCMR_SM_GCI	((ushort)0x0000)
+#define SMCMR_SM_UART	((ushort)0x0020)
+#define SMCMR_SM_TRANS	((ushort)0x0030)
+#define SMCMR_SM_MASK	((ushort)0x0030)
+#define SMCMR_PM_EVEN	((ushort)0x0100)	/* Even parity, else odd */
+#define SMCMR_REVD	SMCMR_PM_EVEN
+#define SMCMR_PEN	((ushort)0x0200)	/* Parity enable */
+#define SMCMR_BS	SMCMR_PEN
+#define SMCMR_SL	((ushort)0x0400)	/* Two stops, else one */
+#define SMCR_CLEN_MASK	((ushort)0x7800)	/* Character length */
+#define smcr_mk_clen(C)	(((C) << 11) & SMCR_CLEN_MASK)
+
+/* SMC Event and Mask register.
+*/
+#define SMCM_BRKE       ((unsigned char)0x40)   /* When in UART Mode */
+#define SMCM_BRK        ((unsigned char)0x10)   /* When in UART Mode */
+#define SMCM_TXE	((unsigned char)0x10)
+#define SMCM_BSY	((unsigned char)0x04)
+#define SMCM_TX		((unsigned char)0x02)
+#define SMCM_RX		((unsigned char)0x01)
+
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST		((uint)0x00020000)
+#define CPM_BRG_EN		((uint)0x00010000)
+#define CPM_BRG_EXTC_INT	((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK3_9	((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK5_15	((uint)0x00008000)
+#define CPM_BRG_ATB		((uint)0x00002000)
+#define CPM_BRG_CD_MASK		((uint)0x00001ffe)
+#define CPM_BRG_DIV16		((uint)0x00000001)
+
+/* SCCs.
+*/
+#define SCC_GSMRH_IRP		((uint)0x00040000)
+#define SCC_GSMRH_GDE		((uint)0x00010000)
+#define SCC_GSMRH_TCRC_CCITT	((uint)0x00008000)
+#define SCC_GSMRH_TCRC_BISYNC	((uint)0x00004000)
+#define SCC_GSMRH_TCRC_HDLC	((uint)0x00000000)
+#define SCC_GSMRH_REVD		((uint)0x00002000)
+#define SCC_GSMRH_TRX		((uint)0x00001000)
+#define SCC_GSMRH_TTX		((uint)0x00000800)
+#define SCC_GSMRH_CDP		((uint)0x00000400)
+#define SCC_GSMRH_CTSP		((uint)0x00000200)
+#define SCC_GSMRH_CDS		((uint)0x00000100)
+#define SCC_GSMRH_CTSS		((uint)0x00000080)
+#define SCC_GSMRH_TFL		((uint)0x00000040)
+#define SCC_GSMRH_RFW		((uint)0x00000020)
+#define SCC_GSMRH_TXSY		((uint)0x00000010)
+#define SCC_GSMRH_SYNL16	((uint)0x0000000c)
+#define SCC_GSMRH_SYNL8		((uint)0x00000008)
+#define SCC_GSMRH_SYNL4		((uint)0x00000004)
+#define SCC_GSMRH_RTSM		((uint)0x00000002)
+#define SCC_GSMRH_RSYN		((uint)0x00000001)
+
+#define SCC_GSMRL_SIR		((uint)0x80000000)	/* SCC2 only */
+#define SCC_GSMRL_EDGE_NONE	((uint)0x60000000)
+#define SCC_GSMRL_EDGE_NEG	((uint)0x40000000)
+#define SCC_GSMRL_EDGE_POS	((uint)0x20000000)
+#define SCC_GSMRL_EDGE_BOTH	((uint)0x00000000)
+#define SCC_GSMRL_TCI		((uint)0x10000000)
+#define SCC_GSMRL_TSNC_3	((uint)0x0c000000)
+#define SCC_GSMRL_TSNC_4	((uint)0x08000000)
+#define SCC_GSMRL_TSNC_14	((uint)0x04000000)
+#define SCC_GSMRL_TSNC_INF	((uint)0x00000000)
+#define SCC_GSMRL_RINV		((uint)0x02000000)
+#define SCC_GSMRL_TINV		((uint)0x01000000)
+#define SCC_GSMRL_TPL_128	((uint)0x00c00000)
+#define SCC_GSMRL_TPL_64	((uint)0x00a00000)
+#define SCC_GSMRL_TPL_48	((uint)0x00800000)
+#define SCC_GSMRL_TPL_32	((uint)0x00600000)
+#define SCC_GSMRL_TPL_16	((uint)0x00400000)
+#define SCC_GSMRL_TPL_8		((uint)0x00200000)
+#define SCC_GSMRL_TPL_NONE	((uint)0x00000000)
+#define SCC_GSMRL_TPP_ALL1	((uint)0x00180000)
+#define SCC_GSMRL_TPP_01	((uint)0x00100000)
+#define SCC_GSMRL_TPP_10	((uint)0x00080000)
+#define SCC_GSMRL_TPP_ZEROS	((uint)0x00000000)
+#define SCC_GSMRL_TEND		((uint)0x00040000)
+#define SCC_GSMRL_TDCR_32	((uint)0x00030000)
+#define SCC_GSMRL_TDCR_16	((uint)0x00020000)
+#define SCC_GSMRL_TDCR_8	((uint)0x00010000)
+#define SCC_GSMRL_TDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RDCR_32	((uint)0x0000c000)
+#define SCC_GSMRL_RDCR_16	((uint)0x00008000)
+#define SCC_GSMRL_RDCR_8	((uint)0x00004000)
+#define SCC_GSMRL_RDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RENC_DFMAN	((uint)0x00003000)
+#define SCC_GSMRL_RENC_MANCH	((uint)0x00002000)
+#define SCC_GSMRL_RENC_FM0	((uint)0x00001000)
+#define SCC_GSMRL_RENC_NRZI	((uint)0x00000800)
+#define SCC_GSMRL_RENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_TENC_DFMAN	((uint)0x00000600)
+#define SCC_GSMRL_TENC_MANCH	((uint)0x00000400)
+#define SCC_GSMRL_TENC_FM0	((uint)0x00000200)
+#define SCC_GSMRL_TENC_NRZI	((uint)0x00000100)
+#define SCC_GSMRL_TENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_DIAG_LE	((uint)0x000000c0)	/* Loop and echo */
+#define SCC_GSMRL_DIAG_ECHO	((uint)0x00000080)
+#define SCC_GSMRL_DIAG_LOOP	((uint)0x00000040)
+#define SCC_GSMRL_DIAG_NORM	((uint)0x00000000)
+#define SCC_GSMRL_ENR		((uint)0x00000020)
+#define SCC_GSMRL_ENT		((uint)0x00000010)
+#define SCC_GSMRL_MODE_ENET	((uint)0x0000000c)
+#define SCC_GSMRL_MODE_DDCMP	((uint)0x00000009)
+#define SCC_GSMRL_MODE_BISYNC	((uint)0x00000008)
+#define SCC_GSMRL_MODE_V14	((uint)0x00000007)
+#define SCC_GSMRL_MODE_AHDLC	((uint)0x00000006)
+#define SCC_GSMRL_MODE_PROFIBUS	((uint)0x00000005)
+#define SCC_GSMRL_MODE_UART	((uint)0x00000004)
+#define SCC_GSMRL_MODE_SS7	((uint)0x00000003)
+#define SCC_GSMRL_MODE_ATALK	((uint)0x00000002)
+#define SCC_GSMRL_MODE_HDLC	((uint)0x00000000)
+
+#define SCC_TODR_TOD		((ushort)0x8000)
+
+/* SCC Event and Mask register.
+*/
+#define SCCM_TXE	((unsigned char)0x10)
+#define SCCM_BSY	((unsigned char)0x04)
+#define SCCM_TX		((unsigned char)0x02)
+#define SCCM_RX		((unsigned char)0x01)
+
+typedef struct scc_param {
+	ushort	scc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	scc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	scc_rfcr;	/* Rx function code */
+	u_char	scc_tfcr;	/* Tx function code */
+	ushort	scc_mrblr;	/* Max receive buffer length */
+	uint	scc_rstate;	/* Internal */
+	uint	scc_idp;	/* Internal */
+	ushort	scc_rbptr;	/* Internal */
+	ushort	scc_ibc;	/* Internal */
+	uint	scc_rxtmp;	/* Internal */
+	uint	scc_tstate;	/* Internal */
+	uint	scc_tdp;	/* Internal */
+	ushort	scc_tbptr;	/* Internal */
+	ushort	scc_tbc;	/* Internal */
+	uint	scc_txtmp;	/* Internal */
+	uint	scc_rcrc;	/* Internal */
+	uint	scc_tcrc;	/* Internal */
+} sccp_t;
+
+/* CPM Ethernet through SCC1.
+ */
+typedef struct scc_enet {
+	sccp_t	sen_genscc;
+	uint	sen_cpres;	/* Preset CRC */
+	uint	sen_cmask;	/* Constant mask for CRC */
+	uint	sen_crcec;	/* CRC Error counter */
+	uint	sen_alec;	/* alignment error counter */
+	uint	sen_disfc;	/* discard frame counter */
+	ushort	sen_pads;	/* Tx short frame pad character */
+	ushort	sen_retlim;	/* Retry limit threshold */
+	ushort	sen_retcnt;	/* Retry limit counter */
+	ushort	sen_maxflr;	/* maximum frame length register */
+	ushort	sen_minflr;	/* minimum frame length register */
+	ushort	sen_maxd1;	/* maximum DMA1 length */
+	ushort	sen_maxd2;	/* maximum DMA2 length */
+	ushort	sen_maxd;	/* Rx max DMA */
+	ushort	sen_dmacnt;	/* Rx DMA counter */
+	ushort	sen_maxb;	/* Max BD byte count */
+	ushort	sen_gaddr1;	/* Group address filter */
+	ushort	sen_gaddr2;
+	ushort	sen_gaddr3;
+	ushort	sen_gaddr4;
+	uint	sen_tbuf0data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf0data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf0rba;	/* Internal */
+	uint	sen_tbuf0crc;	/* Internal */
+	ushort	sen_tbuf0bcnt;	/* Internal */
+	ushort	sen_paddrh;	/* physical address (MSB) */
+	ushort	sen_paddrm;
+	ushort	sen_paddrl;	/* physical address (LSB) */
+	ushort	sen_pper;	/* persistence */
+	ushort	sen_rfbdptr;	/* Rx first BD pointer */
+	ushort	sen_tfbdptr;	/* Tx first BD pointer */
+	ushort	sen_tlbdptr;	/* Tx last BD pointer */
+	uint	sen_tbuf1data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf1data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf1rba;	/* Internal */
+	uint	sen_tbuf1crc;	/* Internal */
+	ushort	sen_tbuf1bcnt;	/* Internal */
+	ushort	sen_txlen;	/* Tx Frame length counter */
+	ushort	sen_iaddr1;	/* Individual address filter */
+	ushort	sen_iaddr2;
+	ushort	sen_iaddr3;
+	ushort	sen_iaddr4;
+	ushort	sen_boffcnt;	/* Backoff counter */
+
+	/* NOTE: Some versions of the manual have the following items
+	 * incorrectly documented.  Below is the proper order.
+	 */
+	ushort	sen_taddrh;	/* temp address (MSB) */
+	ushort	sen_taddrm;
+	ushort	sen_taddrl;	/* temp address (LSB) */
+} scc_enet_t;
+
+
+/* SCC Event register as used by Ethernet.
+*/
+#define SCCE_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */
+#define SCCE_ENET_TXE	((ushort)0x0010)	/* Transmit Error */
+#define SCCE_ENET_RXF	((ushort)0x0008)	/* Full frame received */
+#define SCCE_ENET_BSY	((ushort)0x0004)	/* All incoming buffers full */
+#define SCCE_ENET_TXB	((ushort)0x0002)	/* A buffer was transmitted */
+#define SCCE_ENET_RXB	((ushort)0x0001)	/* A buffer was received */
+
+/* SCC Mode Register (PSMR) as used by Ethernet.
+*/
+#define SCC_PSMR_HBC	((ushort)0x8000)	/* Enable heartbeat */
+#define SCC_PSMR_FC	((ushort)0x4000)	/* Force collision */
+#define SCC_PSMR_RSH	((ushort)0x2000)	/* Receive short frames */
+#define SCC_PSMR_IAM	((ushort)0x1000)	/* Check individual hash */
+#define SCC_PSMR_ENCRC	((ushort)0x0800)	/* Ethernet CRC mode */
+#define SCC_PSMR_PRO	((ushort)0x0200)	/* Promiscuous mode */
+#define SCC_PSMR_BRO	((ushort)0x0100)	/* Catch broadcast pkts */
+#define SCC_PSMR_SBT	((ushort)0x0080)	/* Special backoff timer */
+#define SCC_PSMR_LPB	((ushort)0x0040)	/* Set Loopback mode */
+#define SCC_PSMR_SIP	((ushort)0x0020)	/* Sample Input Pins */
+#define SCC_PSMR_LCW	((ushort)0x0010)	/* Late collision window */
+#define SCC_PSMR_NIB22	((ushort)0x000a)	/* Start frame search */
+#define SCC_PSMR_FDE	((ushort)0x0001)	/* Full duplex enable */
+
+/* Buffer descriptor control/status used by Ethernet receive.
+ * Common to SCC and FCC.
+ */
+#define BD_ENET_RX_EMPTY	((ushort)0x8000)
+#define BD_ENET_RX_WRAP		((ushort)0x2000)
+#define BD_ENET_RX_INTR		((ushort)0x1000)
+#define BD_ENET_RX_LAST		((ushort)0x0800)
+#define BD_ENET_RX_FIRST	((ushort)0x0400)
+#define BD_ENET_RX_MISS		((ushort)0x0100)
+#define BD_ENET_RX_BC		((ushort)0x0080)	/* FCC Only */
+#define BD_ENET_RX_MC		((ushort)0x0040)	/* FCC Only */
+#define BD_ENET_RX_LG		((ushort)0x0020)
+#define BD_ENET_RX_NO		((ushort)0x0010)
+#define BD_ENET_RX_SH		((ushort)0x0008)
+#define BD_ENET_RX_CR		((ushort)0x0004)
+#define BD_ENET_RX_OV		((ushort)0x0002)
+#define BD_ENET_RX_CL		((ushort)0x0001)
+#define BD_ENET_RX_STATS	((ushort)0x01ff)	/* All status bits */
+
+/* Buffer descriptor control/status used by Ethernet transmit.
+ * Common to SCC and FCC.
+ */
+#define BD_ENET_TX_READY	((ushort)0x8000)
+#define BD_ENET_TX_PAD		((ushort)0x4000)
+#define BD_ENET_TX_WRAP		((ushort)0x2000)
+#define BD_ENET_TX_INTR		((ushort)0x1000)
+#define BD_ENET_TX_LAST		((ushort)0x0800)
+#define BD_ENET_TX_TC		((ushort)0x0400)
+#define BD_ENET_TX_DEF		((ushort)0x0200)
+#define BD_ENET_TX_HB		((ushort)0x0100)
+#define BD_ENET_TX_LC		((ushort)0x0080)
+#define BD_ENET_TX_RL		((ushort)0x0040)
+#define BD_ENET_TX_RCMASK	((ushort)0x003c)
+#define BD_ENET_TX_UN		((ushort)0x0002)
+#define BD_ENET_TX_CSL		((ushort)0x0001)
+#define BD_ENET_TX_STATS	((ushort)0x03ff)	/* All status bits */
+
+/* SCC as UART
+*/
+typedef struct scc_uart {
+	sccp_t	scc_genscc;
+	uint	scc_res1;	/* Reserved */
+	uint	scc_res2;	/* Reserved */
+	ushort	scc_maxidl;	/* Maximum idle chars */
+	ushort	scc_idlc;	/* temp idle counter */
+	ushort	scc_brkcr;	/* Break count register */
+	ushort	scc_parec;	/* receive parity error counter */
+	ushort	scc_frmec;	/* receive framing error counter */
+	ushort	scc_nosec;	/* receive noise counter */
+	ushort	scc_brkec;	/* receive break condition counter */
+	ushort	scc_brkln;	/* last received break length */
+	ushort	scc_uaddr1;	/* UART address character 1 */
+	ushort	scc_uaddr2;	/* UART address character 2 */
+	ushort	scc_rtemp;	/* Temp storage */
+	ushort	scc_toseq;	/* Transmit out of sequence char */
+	ushort	scc_char1;	/* control character 1 */
+	ushort	scc_char2;	/* control character 2 */
+	ushort	scc_char3;	/* control character 3 */
+	ushort	scc_char4;	/* control character 4 */
+	ushort	scc_char5;	/* control character 5 */
+	ushort	scc_char6;	/* control character 6 */
+	ushort	scc_char7;	/* control character 7 */
+	ushort	scc_char8;	/* control character 8 */
+	ushort	scc_rccm;	/* receive control character mask */
+	ushort	scc_rccr;	/* receive control character register */
+	ushort	scc_rlbc;	/* receive last break character */
+} scc_uart_t;
+
+/* SCC Event and Mask registers when it is used as a UART.
+*/
+#define UART_SCCM_GLR		((ushort)0x1000)
+#define UART_SCCM_GLT		((ushort)0x0800)
+#define UART_SCCM_AB		((ushort)0x0200)
+#define UART_SCCM_IDL		((ushort)0x0100)
+#define UART_SCCM_GRA		((ushort)0x0080)
+#define UART_SCCM_BRKE		((ushort)0x0040)
+#define UART_SCCM_BRKS		((ushort)0x0020)
+#define UART_SCCM_CCR		((ushort)0x0008)
+#define UART_SCCM_BSY		((ushort)0x0004)
+#define UART_SCCM_TX		((ushort)0x0002)
+#define UART_SCCM_RX		((ushort)0x0001)
+
+/* The SCC PSMR when used as a UART.
+*/
+#define SCU_PSMR_FLC		((ushort)0x8000)
+#define SCU_PSMR_SL		((ushort)0x4000)
+#define SCU_PSMR_CL		((ushort)0x3000)
+#define SCU_PSMR_UM		((ushort)0x0c00)
+#define SCU_PSMR_FRZ		((ushort)0x0200)
+#define SCU_PSMR_RZS		((ushort)0x0100)
+#define SCU_PSMR_SYN		((ushort)0x0080)
+#define SCU_PSMR_DRT		((ushort)0x0040)
+#define SCU_PSMR_PEN		((ushort)0x0010)
+#define SCU_PSMR_RPM		((ushort)0x000c)
+#define SCU_PSMR_REVP		((ushort)0x0008)
+#define SCU_PSMR_TPM		((ushort)0x0003)
+#define SCU_PSMR_TEVP		((ushort)0x0002)
+
+/* CPM Transparent mode SCC.
+ */
+typedef struct scc_trans {
+	sccp_t	st_genscc;
+	uint	st_cpres;	/* Preset CRC */
+	uint	st_cmask;	/* Constant mask for CRC */
+} scc_trans_t;
+
+#define BD_SCC_TX_LAST		((ushort)0x0800)
+
+/* How about some FCCs.....
+*/
+#define FCC_GFMR_DIAG_NORM	((uint)0x00000000)
+#define FCC_GFMR_DIAG_LE	((uint)0x40000000)
+#define FCC_GFMR_DIAG_AE	((uint)0x80000000)
+#define FCC_GFMR_DIAG_ALE	((uint)0xc0000000)
+#define FCC_GFMR_TCI		((uint)0x20000000)
+#define FCC_GFMR_TRX		((uint)0x10000000)
+#define FCC_GFMR_TTX		((uint)0x08000000)
+#define FCC_GFMR_TTX		((uint)0x08000000)
+#define FCC_GFMR_CDP		((uint)0x04000000)
+#define FCC_GFMR_CTSP		((uint)0x02000000)
+#define FCC_GFMR_CDS		((uint)0x01000000)
+#define FCC_GFMR_CTSS		((uint)0x00800000)
+#define FCC_GFMR_SYNL_NONE	((uint)0x00000000)
+#define FCC_GFMR_SYNL_AUTO	((uint)0x00004000)
+#define FCC_GFMR_SYNL_8		((uint)0x00008000)
+#define FCC_GFMR_SYNL_16	((uint)0x0000c000)
+#define FCC_GFMR_RTSM		((uint)0x00002000)
+#define FCC_GFMR_RENC_NRZ	((uint)0x00000000)
+#define FCC_GFMR_RENC_NRZI	((uint)0x00000800)
+#define FCC_GFMR_REVD		((uint)0x00000400)
+#define FCC_GFMR_TENC_NRZ	((uint)0x00000000)
+#define FCC_GFMR_TENC_NRZI	((uint)0x00000100)
+#define FCC_GFMR_TCRC_16	((uint)0x00000000)
+#define FCC_GFMR_TCRC_32	((uint)0x00000080)
+#define FCC_GFMR_ENR		((uint)0x00000020)
+#define FCC_GFMR_ENT		((uint)0x00000010)
+#define FCC_GFMR_MODE_ENET	((uint)0x0000000c)
+#define FCC_GFMR_MODE_ATM	((uint)0x0000000a)
+#define FCC_GFMR_MODE_HDLC	((uint)0x00000000)
+
+/* Generic FCC parameter ram.
+*/
+typedef struct fcc_param {
+	ushort	fcc_riptr;	/* Rx Internal temp pointer */
+	ushort	fcc_tiptr;	/* Tx Internal temp pointer */
+	ushort	fcc_res1;
+	ushort	fcc_mrblr;	/* Max receive buffer length, mod 32 bytes */
+	uint	fcc_rstate;	/* Upper byte is Func code, must be set */
+	uint	fcc_rbase;	/* Receive BD base */
+	ushort	fcc_rbdstat;	/* RxBD status */
+	ushort	fcc_rbdlen;	/* RxBD down counter */
+	uint	fcc_rdptr;	/* RxBD internal data pointer */
+	uint	fcc_tstate;	/* Upper byte is Func code, must be set */
+	uint	fcc_tbase;	/* Transmit BD base */
+	ushort	fcc_tbdstat;	/* TxBD status */
+	ushort	fcc_tbdlen;	/* TxBD down counter */
+	uint	fcc_tdptr;	/* TxBD internal data pointer */
+	uint	fcc_rbptr;	/* Rx BD Internal buf pointer */
+	uint	fcc_tbptr;	/* Tx BD Internal buf pointer */
+	uint	fcc_rcrc;	/* Rx temp CRC */
+	uint	fcc_res2;
+	uint	fcc_tcrc;	/* Tx temp CRC */
+} fccp_t;
+
+
+/* Ethernet controller through FCC.
+*/
+typedef struct fcc_enet {
+	fccp_t	fen_genfcc;
+	uint	fen_statbuf;	/* Internal status buffer */
+	uint	fen_camptr;	/* CAM address */
+	uint	fen_cmask;	/* Constant mask for CRC */
+	uint	fen_cpres;	/* Preset CRC */
+	uint	fen_crcec;	/* CRC Error counter */
+	uint	fen_alec;	/* alignment error counter */
+	uint	fen_disfc;	/* discard frame counter */
+	ushort	fen_retlim;	/* Retry limit */
+	ushort	fen_retcnt;	/* Retry counter */
+	ushort	fen_pper;	/* Persistence */
+	ushort	fen_boffcnt;	/* backoff counter */
+	uint	fen_gaddrh;	/* Group address filter, high 32-bits */
+	uint	fen_gaddrl;	/* Group address filter, low 32-bits */
+	ushort	fen_tfcstat;	/* out of sequence TxBD */
+	ushort	fen_tfclen;
+	uint	fen_tfcptr;
+	ushort	fen_mflr;	/* Maximum frame length (1518) */
+	ushort	fen_paddrh;	/* MAC address */
+	ushort	fen_paddrm;
+	ushort	fen_paddrl;
+	ushort	fen_ibdcount;	/* Internal BD counter */
+	ushort	fen_ibdstart;	/* Internal BD start pointer */
+	ushort	fen_ibdend;	/* Internal BD end pointer */
+	ushort	fen_txlen;	/* Internal Tx frame length counter */
+	uint	fen_ibdbase[8]; /* Internal use */
+	uint	fen_iaddrh;	/* Individual address filter */
+	uint	fen_iaddrl;
+	ushort	fen_minflr;	/* Minimum frame length (64) */
+	ushort	fen_taddrh;	/* Filter transfer MAC address */
+	ushort	fen_taddrm;
+	ushort	fen_taddrl;
+	ushort	fen_padptr;	/* Pointer to pad byte buffer */
+	ushort	fen_cftype;	/* control frame type */
+	ushort	fen_cfrange;	/* control frame range */
+	ushort	fen_maxb;	/* maximum BD count */
+	ushort	fen_maxd1;	/* Max DMA1 length (1520) */
+	ushort	fen_maxd2;	/* Max DMA2 length (1520) */
+	ushort	fen_maxd;	/* internal max DMA count */
+	ushort	fen_dmacnt;	/* internal DMA counter */
+	uint	fen_octc;	/* Total octect counter */
+	uint	fen_colc;	/* Total collision counter */
+	uint	fen_broc;	/* Total broadcast packet counter */
+	uint	fen_mulc;	/* Total multicast packet count */
+	uint	fen_uspc;	/* Total packets < 64 bytes */
+	uint	fen_frgc;	/* Total packets < 64 bytes with errors */
+	uint	fen_ospc;	/* Total packets > 1518 */
+	uint	fen_jbrc;	/* Total packets > 1518 with errors */
+	uint	fen_p64c;	/* Total packets == 64 bytes */
+	uint	fen_p65c;	/* Total packets 64 < bytes <= 127 */
+	uint	fen_p128c;	/* Total packets 127 < bytes <= 255 */
+	uint	fen_p256c;	/* Total packets 256 < bytes <= 511 */
+	uint	fen_p512c;	/* Total packets 512 < bytes <= 1023 */
+	uint	fen_p1024c;	/* Total packets 1024 < bytes <= 1518 */
+	uint	fen_cambuf;	/* Internal CAM buffer poiner */
+	ushort	fen_rfthr;	/* Received frames threshold */
+	ushort	fen_rfcnt;	/* Received frames count */
+} fcc_enet_t;
+
+/* FCC Event/Mask register as used by Ethernet.
+*/
+#define FCC_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */
+#define FCC_ENET_RXC	((ushort)0x0040)	/* Control Frame Received */
+#define FCC_ENET_TXC	((ushort)0x0020)	/* Out of seq. Tx sent */
+#define FCC_ENET_TXE	((ushort)0x0010)	/* Transmit Error */
+#define FCC_ENET_RXF	((ushort)0x0008)	/* Full frame received */
+#define FCC_ENET_BSY	((ushort)0x0004)	/* Busy.  Rx Frame dropped */
+#define FCC_ENET_TXB	((ushort)0x0002)	/* A buffer was transmitted */
+#define FCC_ENET_RXB	((ushort)0x0001)	/* A buffer was received */
+
+/* FCC Mode Register (FPSMR) as used by Ethernet.
+*/
+#define FCC_PSMR_HBC	((uint)0x80000000)	/* Enable heartbeat */
+#define FCC_PSMR_FC	((uint)0x40000000)	/* Force Collision */
+#define FCC_PSMR_SBT	((uint)0x20000000)	/* Stop backoff timer */
+#define FCC_PSMR_LPB	((uint)0x10000000)	/* Local protect. 1 = FDX */
+#define FCC_PSMR_LCW	((uint)0x08000000)	/* Late collision select */
+#define FCC_PSMR_FDE	((uint)0x04000000)	/* Full Duplex Enable */
+#define FCC_PSMR_MON	((uint)0x02000000)	/* RMON Enable */
+#define FCC_PSMR_PRO	((uint)0x00400000)	/* Promiscuous Enable */
+#define FCC_PSMR_FCE	((uint)0x00200000)	/* Flow Control Enable */
+#define FCC_PSMR_RSH	((uint)0x00100000)	/* Receive Short Frames */
+#define FCC_PSMR_CAM	((uint)0x00000400)	/* CAM enable */
+#define FCC_PSMR_BRO	((uint)0x00000200)	/* Broadcast pkt discard */
+#define FCC_PSMR_ENCRC	((uint)0x00000080)	/* Use 32-bit CRC */
+
+/* IIC parameter RAM.
+*/
+typedef struct iic {
+	ushort	iic_rbase;	/* Rx Buffer descriptor base address */
+	ushort	iic_tbase;	/* Tx Buffer descriptor base address */
+	u_char	iic_rfcr;	/* Rx function code */
+	u_char	iic_tfcr;	/* Tx function code */
+	ushort	iic_mrblr;	/* Max receive buffer length */
+	uint	iic_rstate;	/* Internal */
+	uint	iic_rdp;	/* Internal */
+	ushort	iic_rbptr;	/* Internal */
+	ushort	iic_rbc;	/* Internal */
+	uint	iic_rxtmp;	/* Internal */
+	uint	iic_tstate;	/* Internal */
+	uint	iic_tdp;	/* Internal */
+	ushort	iic_tbptr;	/* Internal */
+	ushort	iic_tbc;	/* Internal */
+	uint	iic_txtmp;	/* Internal */
+} iic_t;
+
+/* SPI parameter RAM.
+*/
+typedef struct spi {
+	ushort	spi_rbase;	/* Rx Buffer descriptor base address */
+	ushort	spi_tbase;	/* Tx Buffer descriptor base address */
+	u_char	spi_rfcr;	/* Rx function code */
+	u_char	spi_tfcr;	/* Tx function code */
+	ushort	spi_mrblr;	/* Max receive buffer length */
+	uint	spi_rstate;	/* Internal */
+	uint	spi_rdp;	/* Internal */
+	ushort	spi_rbptr;	/* Internal */
+	ushort	spi_rbc;	/* Internal */
+	uint	spi_rxtmp;	/* Internal */
+	uint	spi_tstate;	/* Internal */
+	uint	spi_tdp;	/* Internal */
+	ushort	spi_tbptr;	/* Internal */
+	ushort	spi_tbc;	/* Internal */
+	uint	spi_txtmp;	/* Internal */
+	uint	spi_res;	/* Tx temp. */
+	uint	spi_res1[4];	/* SDMA temp. */
+} spi_t;
+
+/* SPI Mode register.
+*/
+#define SPMODE_LOOP	((ushort)0x4000)	/* Loopback */
+#define SPMODE_CI	((ushort)0x2000)	/* Clock Invert */
+#define SPMODE_CP	((ushort)0x1000)	/* Clock Phase */
+#define SPMODE_DIV16	((ushort)0x0800)	/* BRG/16 mode */
+#define SPMODE_REV	((ushort)0x0400)	/* Reversed Data */
+#define SPMODE_MSTR	((ushort)0x0200)	/* SPI Master */
+#define SPMODE_EN	((ushort)0x0100)	/* Enable */
+#define SPMODE_LENMSK	((ushort)0x00f0)	/* character length */
+#define SPMODE_PMMSK	((ushort)0x000f)	/* prescale modulus */
+
+#define SPMODE_LEN(x)	((((x)-1)&0xF)<<4)
+#define SPMODE_PM(x)	((x) &0xF)
+
+#define SPI_EB		((u_char)0x10)		/* big endian byte order */
+
+#define BD_IIC_START		((ushort)0x0400)
+
+/* IDMA parameter RAM
+*/
+typedef struct idma {
+	ushort ibase;		/* IDMA buffer descriptor table base address */
+	ushort dcm;		/* DMA channel mode */
+	ushort ibdptr;		/* IDMA current buffer descriptor pointer */
+	ushort dpr_buf;		/* IDMA transfer buffer base address */
+	ushort buf_inv;		/* internal buffer inventory */
+	ushort ss_max;		/* steady-state maximum transfer size */
+	ushort dpr_in_ptr;	/* write pointer inside the internal buffer */
+	ushort sts;		/* source transfer size */
+	ushort dpr_out_ptr;	/* read pointer inside the internal buffer */
+	ushort seob;		/* source end of burst */
+	ushort deob;		/* destination end of burst */
+	ushort dts;		/* destination transfer size */
+	ushort ret_add;		/* return address when working in ERM=1 mode */
+	ushort res0;		/* reserved */
+	uint   bd_cnt;		/* internal byte count */
+	uint   s_ptr;		/* source internal data pointer */
+	uint   d_ptr;		/* destination internal data pointer */
+	uint   istate;		/* internal state */
+	u_char res1[20];	/* pad to 64-byte length */
+} idma_t;
+
+/* DMA channel mode bit fields
+*/
+#define IDMA_DCM_FB		((ushort)0x8000) /* fly-by mode */
+#define IDMA_DCM_LP		((ushort)0x4000) /* low priority */
+#define IDMA_DCM_TC2		((ushort)0x0400) /* value driven on TC[2] */
+#define IDMA_DCM_DMA_WRAP_MASK	((ushort)0x01c0) /* mask for DMA wrap */
+#define IDMA_DCM_DMA_WRAP_64	((ushort)0x0000) /* 64-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_128	((ushort)0x0040) /* 128-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_256	((ushort)0x0080) /* 256-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_512	((ushort)0x00c0) /* 512-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_1024	((ushort)0x0100) /* 1024-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_2048	((ushort)0x0140) /* 2048-byte DMA xfer buffer */
+#define IDMA_DCM_SINC		((ushort)0x0020) /* source inc addr */
+#define IDMA_DCM_DINC		((ushort)0x0010) /* destination inc addr */
+#define IDMA_DCM_ERM		((ushort)0x0008) /* external request mode */
+#define IDMA_DCM_DT		((ushort)0x0004) /* DONE treatment */
+#define IDMA_DCM_SD_MASK	((ushort)0x0003) /* mask for SD bit field */
+#define IDMA_DCM_SD_MEM2MEM	((ushort)0x0000) /* memory-to-memory xfer */
+#define IDMA_DCM_SD_PER2MEM	((ushort)0x0002) /* peripheral-to-memory xfer */
+#define IDMA_DCM_SD_MEM2PER	((ushort)0x0001) /* memory-to-peripheral xfer */
+
+/* IDMA Buffer Descriptors
+*/
+typedef struct idma_bd {
+	uint flags;
+	uint len;	/* data length */
+	uint src;	/* source data buffer pointer */
+	uint dst;	/* destination data buffer pointer */
+} idma_bd_t;
+
+/* IDMA buffer descriptor flag bit fields
+*/
+#define IDMA_BD_V	((uint)0x80000000)	/* valid */
+#define IDMA_BD_W	((uint)0x20000000)	/* wrap */
+#define IDMA_BD_I	((uint)0x10000000)	/* interrupt */
+#define IDMA_BD_L	((uint)0x08000000)	/* last */
+#define IDMA_BD_CM	((uint)0x02000000)	/* continuous mode */
+#define IDMA_BD_SDN	((uint)0x00400000)	/* source done */
+#define IDMA_BD_DDN	((uint)0x00200000)	/* destination done */
+#define IDMA_BD_DGBL	((uint)0x00100000)	/* destination global */
+#define IDMA_BD_DBO_LE	((uint)0x00040000)	/* little-end dest byte order */
+#define IDMA_BD_DBO_BE	((uint)0x00080000)	/* big-end dest byte order */
+#define IDMA_BD_DDTB	((uint)0x00010000)	/* destination data bus */
+#define IDMA_BD_SGBL	((uint)0x00002000)	/* source global */
+#define IDMA_BD_SBO_LE	((uint)0x00000800)	/* little-end src byte order */
+#define IDMA_BD_SBO_BE	((uint)0x00001000)	/* big-end src byte order */
+#define IDMA_BD_SDTB	((uint)0x00000200)	/* source data bus */
+
+/* per-channel IDMA registers
+*/
+typedef struct im_idma {
+	u_char idsr;			/* IDMAn event status register */
+	u_char res0[3];
+	u_char idmr;			/* IDMAn event mask register */
+	u_char res1[3];
+} im_idma_t;
+
+/* IDMA event register bit fields
+*/
+#define IDMA_EVENT_SC	((unsigned char)0x08)	/* stop completed */
+#define IDMA_EVENT_OB	((unsigned char)0x04)	/* out of buffers */
+#define IDMA_EVENT_EDN	((unsigned char)0x02)	/* external DONE asserted */
+#define IDMA_EVENT_BC	((unsigned char)0x01)	/* buffer descriptor complete */
+
+/* RISC Controller Configuration Register (RCCR) bit fields
+*/
+#define RCCR_TIME	((uint)0x80000000) /* timer enable */
+#define RCCR_TIMEP_MASK	((uint)0x3f000000) /* mask for timer period bit field */
+#define RCCR_DR0M	((uint)0x00800000) /* IDMA0 request mode */
+#define RCCR_DR1M	((uint)0x00400000) /* IDMA1 request mode */
+#define RCCR_DR2M	((uint)0x00000080) /* IDMA2 request mode */
+#define RCCR_DR3M	((uint)0x00000040) /* IDMA3 request mode */
+#define RCCR_DR0QP_MASK	((uint)0x00300000) /* mask for IDMA0 req priority */
+#define RCCR_DR0QP_HIGH ((uint)0x00000000) /* IDMA0 has high req priority */
+#define RCCR_DR0QP_MED	((uint)0x00100000) /* IDMA0 has medium req priority */
+#define RCCR_DR0QP_LOW	((uint)0x00200000) /* IDMA0 has low req priority */
+#define RCCR_DR1QP_MASK	((uint)0x00030000) /* mask for IDMA1 req priority */
+#define RCCR_DR1QP_HIGH ((uint)0x00000000) /* IDMA1 has high req priority */
+#define RCCR_DR1QP_MED	((uint)0x00010000) /* IDMA1 has medium req priority */
+#define RCCR_DR1QP_LOW	((uint)0x00020000) /* IDMA1 has low req priority */
+#define RCCR_DR2QP_MASK	((uint)0x00000030) /* mask for IDMA2 req priority */
+#define RCCR_DR2QP_HIGH ((uint)0x00000000) /* IDMA2 has high req priority */
+#define RCCR_DR2QP_MED	((uint)0x00000010) /* IDMA2 has medium req priority */
+#define RCCR_DR2QP_LOW	((uint)0x00000020) /* IDMA2 has low req priority */
+#define RCCR_DR3QP_MASK	((uint)0x00000003) /* mask for IDMA3 req priority */
+#define RCCR_DR3QP_HIGH ((uint)0x00000000) /* IDMA3 has high req priority */
+#define RCCR_DR3QP_MED	((uint)0x00000001) /* IDMA3 has medium req priority */
+#define RCCR_DR3QP_LOW	((uint)0x00000002) /* IDMA3 has low req priority */
+#define RCCR_EIE	((uint)0x00080000) /* external interrupt enable */
+#define RCCR_SCD	((uint)0x00040000) /* scheduler configuration */
+#define RCCR_ERAM_MASK	((uint)0x0000e000) /* mask for enable RAM microcode */
+#define RCCR_ERAM_0KB	((uint)0x00000000) /* use 0KB of dpram for microcode */
+#define RCCR_ERAM_2KB	((uint)0x00002000) /* use 2KB of dpram for microcode */
+#define RCCR_ERAM_4KB	((uint)0x00004000) /* use 4KB of dpram for microcode */
+#define RCCR_ERAM_6KB	((uint)0x00006000) /* use 6KB of dpram for microcode */
+#define RCCR_ERAM_8KB	((uint)0x00008000) /* use 8KB of dpram for microcode */
+#define RCCR_ERAM_10KB	((uint)0x0000a000) /* use 10KB of dpram for microcode */
+#define RCCR_ERAM_12KB	((uint)0x0000c000) /* use 12KB of dpram for microcode */
+#define RCCR_EDM0	((uint)0x00000800) /* DREQ0 edge detect mode */
+#define RCCR_EDM1	((uint)0x00000400) /* DREQ1 edge detect mode */
+#define RCCR_EDM2	((uint)0x00000200) /* DREQ2 edge detect mode */
+#define RCCR_EDM3	((uint)0x00000100) /* DREQ3 edge detect mode */
+#define RCCR_DEM01	((uint)0x00000008) /* DONE0/DONE1 edge detect mode */
+#define RCCR_DEM23	((uint)0x00000004) /* DONE2/DONE3 edge detect mode */
+
+/*-----------------------------------------------------------------------
+ * CMXFCR - CMX FCC Clock Route Register
+ */
+#define CMXFCR_FC1         0x40000000   /* FCC1 connection              */
+#define CMXFCR_RF1CS_MSK   0x38000000   /* Receive FCC1 Clock Source Mask */
+#define CMXFCR_TF1CS_MSK   0x07000000   /* Transmit FCC1 Clock Source Mask */
+#define CMXFCR_FC2         0x00400000   /* FCC2 connection              */
+#define CMXFCR_RF2CS_MSK   0x00380000   /* Receive FCC2 Clock Source Mask */
+#define CMXFCR_TF2CS_MSK   0x00070000   /* Transmit FCC2 Clock Source Mask */
+#define CMXFCR_FC3         0x00004000   /* FCC3 connection              */
+#define CMXFCR_RF3CS_MSK   0x00003800   /* Receive FCC3 Clock Source Mask */
+#define CMXFCR_TF3CS_MSK   0x00000700   /* Transmit FCC3 Clock Source Mask */
+
+#define CMXFCR_RF1CS_BRG5  0x00000000   /* Receive FCC1 Clock Source is BRG5 */
+#define CMXFCR_RF1CS_BRG6  0x08000000   /* Receive FCC1 Clock Source is BRG6 */
+#define CMXFCR_RF1CS_BRG7  0x10000000   /* Receive FCC1 Clock Source is BRG7 */
+#define CMXFCR_RF1CS_BRG8  0x18000000   /* Receive FCC1 Clock Source is BRG8 */
+#define CMXFCR_RF1CS_CLK9  0x20000000   /* Receive FCC1 Clock Source is CLK9 */
+#define CMXFCR_RF1CS_CLK10 0x28000000   /* Receive FCC1 Clock Source is CLK10 */
+#define CMXFCR_RF1CS_CLK11 0x30000000   /* Receive FCC1 Clock Source is CLK11 */
+#define CMXFCR_RF1CS_CLK12 0x38000000   /* Receive FCC1 Clock Source is CLK12 */
+
+#define CMXFCR_TF1CS_BRG5  0x00000000   /* Transmit FCC1 Clock Source is BRG5 */
+#define CMXFCR_TF1CS_BRG6  0x01000000   /* Transmit FCC1 Clock Source is BRG6 */
+#define CMXFCR_TF1CS_BRG7  0x02000000   /* Transmit FCC1 Clock Source is BRG7 */
+#define CMXFCR_TF1CS_BRG8  0x03000000   /* Transmit FCC1 Clock Source is BRG8 */
+#define CMXFCR_TF1CS_CLK9  0x04000000   /* Transmit FCC1 Clock Source is CLK9 */
+#define CMXFCR_TF1CS_CLK10 0x05000000   /* Transmit FCC1 Clock Source is CLK10 */
+#define CMXFCR_TF1CS_CLK11 0x06000000   /* Transmit FCC1 Clock Source is CLK11 */
+#define CMXFCR_TF1CS_CLK12 0x07000000   /* Transmit FCC1 Clock Source is CLK12 */
+
+#define CMXFCR_RF2CS_BRG5  0x00000000   /* Receive FCC2 Clock Source is BRG5 */
+#define CMXFCR_RF2CS_BRG6  0x00080000   /* Receive FCC2 Clock Source is BRG6 */
+#define CMXFCR_RF2CS_BRG7  0x00100000   /* Receive FCC2 Clock Source is BRG7 */
+#define CMXFCR_RF2CS_BRG8  0x00180000   /* Receive FCC2 Clock Source is BRG8 */
+#define CMXFCR_RF2CS_CLK13 0x00200000   /* Receive FCC2 Clock Source is CLK13 */
+#define CMXFCR_RF2CS_CLK14 0x00280000   /* Receive FCC2 Clock Source is CLK14 */
+#define CMXFCR_RF2CS_CLK15 0x00300000   /* Receive FCC2 Clock Source is CLK15 */
+#define CMXFCR_RF2CS_CLK16 0x00380000   /* Receive FCC2 Clock Source is CLK16 */
+
+#define CMXFCR_TF2CS_BRG5  0x00000000   /* Transmit FCC2 Clock Source is BRG5 */
+#define CMXFCR_TF2CS_BRG6  0x00010000   /* Transmit FCC2 Clock Source is BRG6 */
+#define CMXFCR_TF2CS_BRG7  0x00020000   /* Transmit FCC2 Clock Source is BRG7 */
+#define CMXFCR_TF2CS_BRG8  0x00030000   /* Transmit FCC2 Clock Source is BRG8 */
+#define CMXFCR_TF2CS_CLK13 0x00040000   /* Transmit FCC2 Clock Source is CLK13 */
+#define CMXFCR_TF2CS_CLK14 0x00050000   /* Transmit FCC2 Clock Source is CLK14 */
+#define CMXFCR_TF2CS_CLK15 0x00060000   /* Transmit FCC2 Clock Source is CLK15 */
+#define CMXFCR_TF2CS_CLK16 0x00070000   /* Transmit FCC2 Clock Source is CLK16 */
+
+#define CMXFCR_RF3CS_BRG5  0x00000000   /* Receive FCC3 Clock Source is BRG5 */
+#define CMXFCR_RF3CS_BRG6  0x00000800   /* Receive FCC3 Clock Source is BRG6 */
+#define CMXFCR_RF3CS_BRG7  0x00001000   /* Receive FCC3 Clock Source is BRG7 */
+#define CMXFCR_RF3CS_BRG8  0x00001800   /* Receive FCC3 Clock Source is BRG8 */
+#define CMXFCR_RF3CS_CLK13 0x00002000   /* Receive FCC3 Clock Source is CLK13 */
+#define CMXFCR_RF3CS_CLK14 0x00002800   /* Receive FCC3 Clock Source is CLK14 */
+#define CMXFCR_RF3CS_CLK15 0x00003000   /* Receive FCC3 Clock Source is CLK15 */
+#define CMXFCR_RF3CS_CLK16 0x00003800   /* Receive FCC3 Clock Source is CLK16 */
+
+#define CMXFCR_TF3CS_BRG5  0x00000000   /* Transmit FCC3 Clock Source is BRG5 */
+#define CMXFCR_TF3CS_BRG6  0x00000100   /* Transmit FCC3 Clock Source is BRG6 */
+#define CMXFCR_TF3CS_BRG7  0x00000200   /* Transmit FCC3 Clock Source is BRG7 */
+#define CMXFCR_TF3CS_BRG8  0x00000300   /* Transmit FCC3 Clock Source is BRG8 */
+#define CMXFCR_TF3CS_CLK13 0x00000400   /* Transmit FCC3 Clock Source is CLK13 */
+#define CMXFCR_TF3CS_CLK14 0x00000500   /* Transmit FCC3 Clock Source is CLK14 */
+#define CMXFCR_TF3CS_CLK15 0x00000600   /* Transmit FCC3 Clock Source is CLK15 */
+#define CMXFCR_TF3CS_CLK16 0x00000700   /* Transmit FCC3 Clock Source is CLK16 */
+
+/*-----------------------------------------------------------------------
+ * CMXSCR - CMX SCC Clock Route Register
+ */
+#define CMXSCR_GR1         0x80000000   /* Grant Support of SCC1        */
+#define CMXSCR_SC1         0x40000000   /* SCC1 connection              */
+#define CMXSCR_RS1CS_MSK   0x38000000   /* Receive SCC1 Clock Source Mask */
+#define CMXSCR_TS1CS_MSK   0x07000000   /* Transmit SCC1 Clock Source Mask */
+#define CMXSCR_GR2         0x00800000   /* Grant Support of SCC2        */
+#define CMXSCR_SC2         0x00400000   /* SCC2 connection              */
+#define CMXSCR_RS2CS_MSK   0x00380000   /* Receive SCC2 Clock Source Mask */
+#define CMXSCR_TS2CS_MSK   0x00070000   /* Transmit SCC2 Clock Source Mask */
+#define CMXSCR_GR3         0x00008000   /* Grant Support of SCC3        */
+#define CMXSCR_SC3         0x00004000   /* SCC3 connection              */
+#define CMXSCR_RS3CS_MSK   0x00003800   /* Receive SCC3 Clock Source Mask */
+#define CMXSCR_TS3CS_MSK   0x00000700   /* Transmit SCC3 Clock Source Mask */
+#define CMXSCR_GR4         0x00000080   /* Grant Support of SCC4        */
+#define CMXSCR_SC4         0x00000040   /* SCC4 connection              */
+#define CMXSCR_RS4CS_MSK   0x00000038   /* Receive SCC4 Clock Source Mask */
+#define CMXSCR_TS4CS_MSK   0x00000007   /* Transmit SCC4 Clock Source Mask */
+
+#define CMXSCR_RS1CS_BRG1  0x00000000   /* SCC1 Rx Clock Source is BRG1 */
+#define CMXSCR_RS1CS_BRG2  0x08000000   /* SCC1 Rx Clock Source is BRG2 */
+#define CMXSCR_RS1CS_BRG3  0x10000000   /* SCC1 Rx Clock Source is BRG3 */
+#define CMXSCR_RS1CS_BRG4  0x18000000   /* SCC1 Rx Clock Source is BRG4 */
+#define CMXSCR_RS1CS_CLK11 0x20000000   /* SCC1 Rx Clock Source is CLK11 */
+#define CMXSCR_RS1CS_CLK12 0x28000000   /* SCC1 Rx Clock Source is CLK12 */
+#define CMXSCR_RS1CS_CLK3  0x30000000   /* SCC1 Rx Clock Source is CLK3 */
+#define CMXSCR_RS1CS_CLK4  0x38000000   /* SCC1 Rx Clock Source is CLK4 */
+
+#define CMXSCR_TS1CS_BRG1  0x00000000   /* SCC1 Tx Clock Source is BRG1 */
+#define CMXSCR_TS1CS_BRG2  0x01000000   /* SCC1 Tx Clock Source is BRG2 */
+#define CMXSCR_TS1CS_BRG3  0x02000000   /* SCC1 Tx Clock Source is BRG3 */
+#define CMXSCR_TS1CS_BRG4  0x03000000   /* SCC1 Tx Clock Source is BRG4 */
+#define CMXSCR_TS1CS_CLK11 0x04000000   /* SCC1 Tx Clock Source is CLK11 */
+#define CMXSCR_TS1CS_CLK12 0x05000000   /* SCC1 Tx Clock Source is CLK12 */
+#define CMXSCR_TS1CS_CLK3  0x06000000   /* SCC1 Tx Clock Source is CLK3 */
+#define CMXSCR_TS1CS_CLK4  0x07000000   /* SCC1 Tx Clock Source is CLK4 */
+
+#define CMXSCR_RS2CS_BRG1  0x00000000   /* SCC2 Rx Clock Source is BRG1 */
+#define CMXSCR_RS2CS_BRG2  0x00080000   /* SCC2 Rx Clock Source is BRG2 */
+#define CMXSCR_RS2CS_BRG3  0x00100000   /* SCC2 Rx Clock Source is BRG3 */
+#define CMXSCR_RS2CS_BRG4  0x00180000   /* SCC2 Rx Clock Source is BRG4 */
+#define CMXSCR_RS2CS_CLK11 0x00200000   /* SCC2 Rx Clock Source is CLK11 */
+#define CMXSCR_RS2CS_CLK12 0x00280000   /* SCC2 Rx Clock Source is CLK12 */
+#define CMXSCR_RS2CS_CLK3  0x00300000   /* SCC2 Rx Clock Source is CLK3 */
+#define CMXSCR_RS2CS_CLK4  0x00380000   /* SCC2 Rx Clock Source is CLK4 */
+
+#define CMXSCR_TS2CS_BRG1  0x00000000   /* SCC2 Tx Clock Source is BRG1 */
+#define CMXSCR_TS2CS_BRG2  0x00010000   /* SCC2 Tx Clock Source is BRG2 */
+#define CMXSCR_TS2CS_BRG3  0x00020000   /* SCC2 Tx Clock Source is BRG3 */
+#define CMXSCR_TS2CS_BRG4  0x00030000   /* SCC2 Tx Clock Source is BRG4 */
+#define CMXSCR_TS2CS_CLK11 0x00040000   /* SCC2 Tx Clock Source is CLK11 */
+#define CMXSCR_TS2CS_CLK12 0x00050000   /* SCC2 Tx Clock Source is CLK12 */
+#define CMXSCR_TS2CS_CLK3  0x00060000   /* SCC2 Tx Clock Source is CLK3 */
+#define CMXSCR_TS2CS_CLK4  0x00070000   /* SCC2 Tx Clock Source is CLK4 */
+
+#define CMXSCR_RS3CS_BRG1  0x00000000   /* SCC3 Rx Clock Source is BRG1 */
+#define CMXSCR_RS3CS_BRG2  0x00000800   /* SCC3 Rx Clock Source is BRG2 */
+#define CMXSCR_RS3CS_BRG3  0x00001000   /* SCC3 Rx Clock Source is BRG3 */
+#define CMXSCR_RS3CS_BRG4  0x00001800   /* SCC3 Rx Clock Source is BRG4 */
+#define CMXSCR_RS3CS_CLK5  0x00002000   /* SCC3 Rx Clock Source is CLK5 */
+#define CMXSCR_RS3CS_CLK6  0x00002800   /* SCC3 Rx Clock Source is CLK6 */
+#define CMXSCR_RS3CS_CLK7  0x00003000   /* SCC3 Rx Clock Source is CLK7 */
+#define CMXSCR_RS3CS_CLK8  0x00003800   /* SCC3 Rx Clock Source is CLK8 */
+
+#define CMXSCR_TS3CS_BRG1  0x00000000   /* SCC3 Tx Clock Source is BRG1 */
+#define CMXSCR_TS3CS_BRG2  0x00000100   /* SCC3 Tx Clock Source is BRG2 */
+#define CMXSCR_TS3CS_BRG3  0x00000200   /* SCC3 Tx Clock Source is BRG3 */
+#define CMXSCR_TS3CS_BRG4  0x00000300   /* SCC3 Tx Clock Source is BRG4 */
+#define CMXSCR_TS3CS_CLK5  0x00000400   /* SCC3 Tx Clock Source is CLK5 */
+#define CMXSCR_TS3CS_CLK6  0x00000500   /* SCC3 Tx Clock Source is CLK6 */
+#define CMXSCR_TS3CS_CLK7  0x00000600   /* SCC3 Tx Clock Source is CLK7 */
+#define CMXSCR_TS3CS_CLK8  0x00000700   /* SCC3 Tx Clock Source is CLK8 */
+
+#define CMXSCR_RS4CS_BRG1  0x00000000   /* SCC4 Rx Clock Source is BRG1 */
+#define CMXSCR_RS4CS_BRG2  0x00000008   /* SCC4 Rx Clock Source is BRG2 */
+#define CMXSCR_RS4CS_BRG3  0x00000010   /* SCC4 Rx Clock Source is BRG3 */
+#define CMXSCR_RS4CS_BRG4  0x00000018   /* SCC4 Rx Clock Source is BRG4 */
+#define CMXSCR_RS4CS_CLK5  0x00000020   /* SCC4 Rx Clock Source is CLK5 */
+#define CMXSCR_RS4CS_CLK6  0x00000028   /* SCC4 Rx Clock Source is CLK6 */
+#define CMXSCR_RS4CS_CLK7  0x00000030   /* SCC4 Rx Clock Source is CLK7 */
+#define CMXSCR_RS4CS_CLK8  0x00000038   /* SCC4 Rx Clock Source is CLK8 */
+
+#define CMXSCR_TS4CS_BRG1  0x00000000   /* SCC4 Tx Clock Source is BRG1 */
+#define CMXSCR_TS4CS_BRG2  0x00000001   /* SCC4 Tx Clock Source is BRG2 */
+#define CMXSCR_TS4CS_BRG3  0x00000002   /* SCC4 Tx Clock Source is BRG3 */
+#define CMXSCR_TS4CS_BRG4  0x00000003   /* SCC4 Tx Clock Source is BRG4 */
+#define CMXSCR_TS4CS_CLK5  0x00000004   /* SCC4 Tx Clock Source is CLK5 */
+#define CMXSCR_TS4CS_CLK6  0x00000005   /* SCC4 Tx Clock Source is CLK6 */
+#define CMXSCR_TS4CS_CLK7  0x00000006   /* SCC4 Tx Clock Source is CLK7 */
+#define CMXSCR_TS4CS_CLK8  0x00000007   /* SCC4 Tx Clock Source is CLK8 */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration Register				 4-31
+ */
+#define SIUMCR_BBD	0x80000000	/* Bus Busy Disable		*/
+#define SIUMCR_ESE	0x40000000	/* External Snoop Enable	*/
+#define SIUMCR_PBSE	0x20000000	/* Parity Byte Select Enable	*/
+#define SIUMCR_CDIS	0x10000000	/* Core Disable			*/
+#define SIUMCR_DPPC00	0x00000000	/* Data Parity Pins Configuration*/
+#define SIUMCR_DPPC01	0x04000000	/* - " -			*/
+#define SIUMCR_DPPC10	0x08000000	/* - " -			*/
+#define SIUMCR_DPPC11	0x0c000000	/* - " -			*/
+#define SIUMCR_L2CPC00	0x00000000	/* L2 Cache Pins Configuration	*/
+#define SIUMCR_L2CPC01	0x01000000	/* - " -			*/
+#define SIUMCR_L2CPC10	0x02000000	/* - " -			*/
+#define SIUMCR_L2CPC11	0x03000000	/* - " -			*/
+#define SIUMCR_LBPC00	0x00000000	/* Local Bus Pins Configuration	*/
+#define SIUMCR_LBPC01	0x00400000	/* - " -			*/
+#define SIUMCR_LBPC10	0x00800000	/* - " -			*/
+#define SIUMCR_LBPC11	0x00c00000	/* - " -			*/
+#define SIUMCR_APPC00	0x00000000	/* Address Parity Pins Configuration*/
+#define SIUMCR_APPC01	0x00100000	/* - " -			*/
+#define SIUMCR_APPC10	0x00200000	/* - " -			*/
+#define SIUMCR_APPC11	0x00300000	/* - " -			*/
+#define SIUMCR_CS10PC00	0x00000000	/* CS10 Pin Configuration	*/
+#define SIUMCR_CS10PC01	0x00040000	/* - " -			*/
+#define SIUMCR_CS10PC10	0x00080000	/* - " -			*/
+#define SIUMCR_CS10PC11	0x000c0000	/* - " -			*/
+#define SIUMCR_BCTLC00	0x00000000	/* Buffer Control Configuration	*/
+#define SIUMCR_BCTLC01	0x00010000	/* - " -			*/
+#define SIUMCR_BCTLC10	0x00020000	/* - " -			*/
+#define SIUMCR_BCTLC11	0x00030000	/* - " -			*/
+#define SIUMCR_MMR00	0x00000000	/* Mask Masters Requests	*/
+#define SIUMCR_MMR01	0x00004000	/* - " -			*/
+#define SIUMCR_MMR10	0x00008000	/* - " -			*/
+#define SIUMCR_MMR11	0x0000c000	/* - " -			*/
+#define SIUMCR_LPBSE	0x00002000	/* LocalBus Parity Byte Select Enable*/
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control Register					 9-8
+*/
+#define SCCR_PCI_MODE	0x00000100	/* PCI Mode	*/
+#define SCCR_PCI_MODCK	0x00000080	/* Value of PCI_MODCK pin	*/
+#define SCCR_PCIDF_MSK	0x00000078	/* PCI division factor	*/
+#define SCCR_PCIDF_SHIFT 3
+
+#ifndef CPM_IMMR_OFFSET
+#define CPM_IMMR_OFFSET	0x101a8
+#endif
+
+#define FCC_PSMR_RMII	((uint)0x00020000)	/* Use RMII interface */
+
+/* FCC iop & clock configuration. BSP code is responsible to define Fx_RXCLK & Fx_TXCLK
+ * in order to use clock-computing stuff below for the FCC x
+ */
+
+/* Automatically generates register configurations */
+#define PC_CLK(x)	((uint)(1<<(x-1)))	/* FCC CLK I/O ports */
+
+#define CMXFCR_RF1CS(x)	((uint)((x-5)<<27))	/* FCC1 Receive Clock Source */
+#define CMXFCR_TF1CS(x)	((uint)((x-5)<<24))	/* FCC1 Transmit Clock Source */
+#define CMXFCR_RF2CS(x)	((uint)((x-9)<<19))	/* FCC2 Receive Clock Source */
+#define CMXFCR_TF2CS(x) ((uint)((x-9)<<16))	/* FCC2 Transmit Clock Source */
+#define CMXFCR_RF3CS(x)	((uint)((x-9)<<11))	/* FCC3 Receive Clock Source */
+#define CMXFCR_TF3CS(x) ((uint)((x-9)<<8))	/* FCC3 Transmit Clock Source */
+
+#define PC_F1RXCLK	PC_CLK(F1_RXCLK)
+#define PC_F1TXCLK	PC_CLK(F1_TXCLK)
+#define CMX1_CLK_ROUTE	(CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK))
+#define CMX1_CLK_MASK	((uint)0xff000000)
+
+#define PC_F2RXCLK	PC_CLK(F2_RXCLK)
+#define PC_F2TXCLK	PC_CLK(F2_TXCLK)
+#define CMX2_CLK_ROUTE	(CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK))
+#define CMX2_CLK_MASK	((uint)0x00ff0000)
+
+#define PC_F3RXCLK	PC_CLK(F3_RXCLK)
+#define PC_F3TXCLK	PC_CLK(F3_TXCLK)
+#define CMX3_CLK_ROUTE	(CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK))
+#define CMX3_CLK_MASK	((uint)0x0000ff00)
+
+#define CPMUX_CLK_MASK (CMX3_CLK_MASK | CMX2_CLK_MASK)
+#define CPMUX_CLK_ROUTE (CMX3_CLK_ROUTE | CMX2_CLK_ROUTE)
+
+#define CLK_TRX (PC_F3TXCLK | PC_F3RXCLK | PC_F2TXCLK | PC_F2RXCLK)
+
+/* I/O Pin assignment for FCC1.  I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PA1_COL		0x00000001U
+#define PA1_CRS		0x00000002U
+#define PA1_TXER	0x00000004U
+#define PA1_TXEN	0x00000008U
+#define PA1_RXDV	0x00000010U
+#define PA1_RXER	0x00000020U
+#define PA1_TXDAT	0x00003c00U
+#define PA1_RXDAT	0x0003c000U
+#define PA1_PSORA0	(PA1_RXDAT | PA1_TXDAT)
+#define PA1_PSORA1	(PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \
+		PA1_RXDV | PA1_RXER)
+#define PA1_DIRA0	(PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV)
+#define PA1_DIRA1	(PA1_TXDAT | PA1_TXEN | PA1_TXER)
+
+
+/* I/O Pin assignment for FCC2.  I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB2_TXER	0x00000001U
+#define PB2_RXDV	0x00000002U
+#define PB2_TXEN	0x00000004U
+#define PB2_RXER	0x00000008U
+#define PB2_COL		0x00000010U
+#define PB2_CRS		0x00000020U
+#define PB2_TXDAT	0x000003c0U
+#define PB2_RXDAT	0x00003c00U
+#define PB2_PSORB0	(PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \
+		PB2_RXER | PB2_RXDV | PB2_TXER)
+#define PB2_PSORB1	(PB2_TXEN)
+#define PB2_DIRB0	(PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV)
+#define PB2_DIRB1	(PB2_TXDAT | PB2_TXEN | PB2_TXER)
+
+
+/* I/O Pin assignment for FCC3.  I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB3_RXDV	0x00004000U
+#define PB3_RXER	0x00008000U
+#define PB3_TXER	0x00010000U
+#define PB3_TXEN	0x00020000U
+#define PB3_COL		0x00040000U
+#define PB3_CRS		0x00080000U
+#define PB3_TXDAT	0x0f000000U
+#define PC3_TXDAT	0x00000010U
+#define PB3_RXDAT	0x00f00000U
+#define PB3_PSORB0	(PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \
+		PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN)
+#define PB3_PSORB1	0
+#define PB3_DIRB0	(PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV)
+#define PB3_DIRB1	(PB3_TXDAT | PB3_TXEN | PB3_TXER)
+#define PC3_DIRC1	(PC3_TXDAT)
+
+/* Handy macro to specify mem for FCCs*/
+#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
+#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
+#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
+#define FCC3_MEM_OFFSET FCC_MEM_OFFSET(2)
+
+/* Clocks and GRG's */
+
+enum cpm_clk_dir {
+	CPM_CLK_RX,
+	CPM_CLK_TX,
+	CPM_CLK_RTX
+};
+
+enum cpm_clk_target {
+	CPM_CLK_SCC1,
+	CPM_CLK_SCC2,
+	CPM_CLK_SCC3,
+	CPM_CLK_SCC4,
+	CPM_CLK_FCC1,
+	CPM_CLK_FCC2,
+	CPM_CLK_FCC3,
+	CPM_CLK_SMC1,
+	CPM_CLK_SMC2,
+};
+
+enum cpm_clk {
+	CPM_CLK_NONE = 0,
+	CPM_BRG1,	/* Baud Rate Generator  1 */
+	CPM_BRG2,	/* Baud Rate Generator  2 */
+	CPM_BRG3,	/* Baud Rate Generator  3 */
+	CPM_BRG4,	/* Baud Rate Generator  4 */
+	CPM_BRG5,	/* Baud Rate Generator  5 */
+	CPM_BRG6,	/* Baud Rate Generator  6 */
+	CPM_BRG7,	/* Baud Rate Generator  7 */
+	CPM_BRG8,	/* Baud Rate Generator  8 */
+	CPM_CLK1,	/* Clock  1 */
+	CPM_CLK2,	/* Clock  2 */
+	CPM_CLK3,	/* Clock  3 */
+	CPM_CLK4,	/* Clock  4 */
+	CPM_CLK5,	/* Clock  5 */
+	CPM_CLK6,	/* Clock  6 */
+	CPM_CLK7,	/* Clock  7 */
+	CPM_CLK8,	/* Clock  8 */
+	CPM_CLK9,	/* Clock  9 */
+	CPM_CLK10,	/* Clock 10 */
+	CPM_CLK11,	/* Clock 11 */
+	CPM_CLK12,	/* Clock 12 */
+	CPM_CLK13,	/* Clock 13 */
+	CPM_CLK14,	/* Clock 14 */
+	CPM_CLK15,	/* Clock 15 */
+	CPM_CLK16,	/* Clock 16 */
+	CPM_CLK17,	/* Clock 17 */
+	CPM_CLK18,	/* Clock 18 */
+	CPM_CLK19,	/* Clock 19 */
+	CPM_CLK20,	/* Clock 20 */
+	CPM_CLK_DUMMY
+};
+
+extern int cpm2_clk_setup(enum cpm_clk_target target, int clock, int mode);
+extern int cpm2_smc_clk_setup(enum cpm_clk_target target, int clock);
+
+#define CPM_PIN_INPUT     0
+#define CPM_PIN_OUTPUT    1
+#define CPM_PIN_PRIMARY   0
+#define CPM_PIN_SECONDARY 2
+#define CPM_PIN_GPIO      4
+#define CPM_PIN_OPENDRAIN 8
+
+void cpm2_set_pin(int port, int pin, int flags);
+
+#endif /* __CPM2__ */
+#endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/cputable.h b/include/asm-powerpc/cputable.h
index 3dc8e2dfca84..ae093ef68363 100644
--- a/include/asm-powerpc/cputable.h
+++ b/include/asm-powerpc/cputable.h
@@ -57,6 +57,7 @@ enum powerpc_pmc_type {
 	PPC_PMC_PA6T = 2,
 };
 
+/* NOTE WELL: Update identify_cpu() if fields are added or removed! */
 struct cpu_spec {
 	/* CPU is matched via (PVR & pvr_mask) == pvr_value */
 	unsigned int	pvr_mask;
@@ -136,6 +137,7 @@ extern void do_feature_fixups(unsigned long value, void *fixup_start,
 #define CPU_FTR_REAL_LE			ASM_CONST(0x0000000000400000)
 #define CPU_FTR_FPU_UNAVAILABLE		ASM_CONST(0x0000000000800000)
 #define CPU_FTR_UNIFIED_ID_CACHE	ASM_CONST(0x0000000001000000)
+#define CPU_FTR_SPE			ASM_CONST(0x0000000002000000)
 
 /*
  * Add the 64-bit processor unique features in the top half of the word;
@@ -162,6 +164,7 @@ extern void do_feature_fixups(unsigned long value, void *fixup_start,
 #define CPU_FTR_CELL_TB_BUG		LONG_ASM_CONST(0x0000800000000000)
 #define CPU_FTR_SPURR			LONG_ASM_CONST(0x0001000000000000)
 #define CPU_FTR_DSCR			LONG_ASM_CONST(0x0002000000000000)
+#define CPU_FTR_1T_SEGMENT		LONG_ASM_CONST(0x0004000000000000)
 
 #ifndef __ASSEMBLY__
 
@@ -180,12 +183,27 @@ extern void do_feature_fixups(unsigned long value, void *fixup_start,
 #define PPC_FEATURE_HAS_ALTIVEC_COMP    0
 #endif
 
-/* We need to mark all pages as being coherent if we're SMP or we
- * have a 74[45]x and an MPC107 host bridge. Also 83xx requires
- * it for PCI "streaming/prefetch" to work properly.
+/* We only set the spe features if the kernel was compiled with spe
+ * support
+ */
+#ifdef CONFIG_SPE
+#define CPU_FTR_SPE_COMP	CPU_FTR_SPE
+#define PPC_FEATURE_HAS_SPE_COMP PPC_FEATURE_HAS_SPE
+#define PPC_FEATURE_HAS_EFP_SINGLE_COMP PPC_FEATURE_HAS_EFP_SINGLE
+#define PPC_FEATURE_HAS_EFP_DOUBLE_COMP PPC_FEATURE_HAS_EFP_DOUBLE
+#else
+#define CPU_FTR_SPE_COMP	0
+#define PPC_FEATURE_HAS_SPE_COMP    0
+#define PPC_FEATURE_HAS_EFP_SINGLE_COMP 0
+#define PPC_FEATURE_HAS_EFP_DOUBLE_COMP 0
+#endif
+
+/* We need to mark all pages as being coherent if we're SMP or we have a
+ * 74[45]x and an MPC107 host bridge. Also 83xx and PowerQUICC II
+ * require it for PCI "streaming/prefetch" to work properly.
  */
 #if defined(CONFIG_SMP) || defined(CONFIG_MPC10X_BRIDGE) \
-	|| defined(CONFIG_PPC_83xx)
+	|| defined(CONFIG_PPC_83xx) || defined(CONFIG_8260)
 #define CPU_FTR_COMMON                  CPU_FTR_NEED_COHERENT
 #else
 #define CPU_FTR_COMMON                  0
@@ -297,7 +315,7 @@ extern void do_feature_fixups(unsigned long value, void *fixup_start,
 	    CPU_FTR_PPC_LE)
 #define CPU_FTRS_82XX	(CPU_FTR_COMMON | \
 	    CPU_FTR_MAYBE_CAN_DOZE | CPU_FTR_USE_TB)
-#define CPU_FTRS_G2_LE	(CPU_FTR_MAYBE_CAN_DOZE | \
+#define CPU_FTRS_G2_LE	(CPU_FTR_COMMON | CPU_FTR_MAYBE_CAN_DOZE | \
 	    CPU_FTR_USE_TB | CPU_FTR_MAYBE_CAN_NAP | CPU_FTR_HAS_HIGH_BATS)
 #define CPU_FTRS_E300	(CPU_FTR_MAYBE_CAN_DOZE | \
 	    CPU_FTR_USE_TB | CPU_FTR_MAYBE_CAN_NAP | CPU_FTR_HAS_HIGH_BATS | \
@@ -310,10 +328,12 @@ extern void do_feature_fixups(unsigned long value, void *fixup_start,
 #define CPU_FTRS_8XX	(CPU_FTR_USE_TB)
 #define CPU_FTRS_40X	(CPU_FTR_USE_TB | CPU_FTR_NODSISRALIGN)
 #define CPU_FTRS_44X	(CPU_FTR_USE_TB | CPU_FTR_NODSISRALIGN)
-#define CPU_FTRS_E200	(CPU_FTR_USE_TB | CPU_FTR_NODSISRALIGN | \
-	    CPU_FTR_COHERENT_ICACHE | CPU_FTR_UNIFIED_ID_CACHE)
-#define CPU_FTRS_E500	(CPU_FTR_USE_TB | CPU_FTR_NODSISRALIGN)
-#define CPU_FTRS_E500_2	(CPU_FTR_USE_TB | \
+#define CPU_FTRS_E200	(CPU_FTR_USE_TB | CPU_FTR_SPE_COMP | \
+	    CPU_FTR_NODSISRALIGN | CPU_FTR_COHERENT_ICACHE | \
+	    CPU_FTR_UNIFIED_ID_CACHE)
+#define CPU_FTRS_E500	(CPU_FTR_USE_TB | CPU_FTR_SPE_COMP | \
+	    CPU_FTR_NODSISRALIGN)
+#define CPU_FTRS_E500_2	(CPU_FTR_USE_TB | CPU_FTR_SPE_COMP | \
 	    CPU_FTR_BIG_PHYS | CPU_FTR_NODSISRALIGN)
 #define CPU_FTRS_GENERIC_32	(CPU_FTR_COMMON | CPU_FTR_NODSISRALIGN)
 
@@ -355,7 +375,7 @@ extern void do_feature_fixups(unsigned long value, void *fixup_start,
 #define CPU_FTRS_POSSIBLE	\
 	    (CPU_FTRS_POWER3 | CPU_FTRS_RS64 | CPU_FTRS_POWER4 |	\
 	    CPU_FTRS_PPC970 | CPU_FTRS_POWER5 | CPU_FTRS_POWER6 |	\
-	    CPU_FTRS_CELL | CPU_FTRS_PA6T)
+	    CPU_FTRS_CELL | CPU_FTRS_PA6T | CPU_FTR_1T_SEGMENT)
 #else
 enum {
 	CPU_FTRS_POSSIBLE =
diff --git a/include/asm-powerpc/dcr-mmio.h b/include/asm-powerpc/dcr-mmio.h
index 5dbfca8dde36..6b82c3ba495a 100644
--- a/include/asm-powerpc/dcr-mmio.h
+++ b/include/asm-powerpc/dcr-mmio.h
@@ -23,7 +23,11 @@
 
 #include <asm/io.h>
 
-typedef struct { void __iomem *token; unsigned int stride; } dcr_host_t;
+typedef struct {
+	void __iomem *token;
+	unsigned int stride;
+	unsigned int base;
+} dcr_host_t;
 
 #define DCR_MAP_OK(host)	((host).token != NULL)
 
diff --git a/include/asm-powerpc/dcr-native.h b/include/asm-powerpc/dcr-native.h
index 05af081222f6..f41058c0f6cb 100644
--- a/include/asm-powerpc/dcr-native.h
+++ b/include/asm-powerpc/dcr-native.h
@@ -22,11 +22,13 @@
 #ifdef __KERNEL__
 #ifndef __ASSEMBLY__
 
-typedef struct {} dcr_host_t;
+typedef struct {
+	unsigned int base;
+} dcr_host_t;
 
 #define DCR_MAP_OK(host)	(1)
 
-#define dcr_map(dev, dcr_n, dcr_c)	((dcr_host_t){})
+#define dcr_map(dev, dcr_n, dcr_c)	((dcr_host_t){ .base = (dcr_n) })
 #define dcr_unmap(host, dcr_n, dcr_c)	do {} while (0)
 #define dcr_read(host, dcr_n)		mfdcr(dcr_n)
 #define dcr_write(host, dcr_n, value)	mtdcr(dcr_n, value)
diff --git a/include/asm-powerpc/dma-mapping.h b/include/asm-powerpc/dma-mapping.h
index 744d6bb24116..d05891608f74 100644
--- a/include/asm-powerpc/dma-mapping.h
+++ b/include/asm-powerpc/dma-mapping.h
@@ -249,8 +249,12 @@ dma_map_single(struct device *dev, void *ptr, size_t size,
 	return virt_to_bus(ptr);
 }
 
-/* We do nothing. */
-#define dma_unmap_single(dev, addr, size, dir)	((void)0)
+static inline void dma_unmap_single(struct device *dev, dma_addr_t dma_addr,
+				    size_t size,
+				    enum dma_data_direction direction)
+{
+	/* We do nothing. */
+}
 
 static inline dma_addr_t
 dma_map_page(struct device *dev, struct page *page,
@@ -264,8 +268,12 @@ dma_map_page(struct device *dev, struct page *page,
 	return page_to_bus(page) + offset;
 }
 
-/* We do nothing. */
-#define dma_unmap_page(dev, handle, size, dir)	((void)0)
+static inline void dma_unmap_page(struct device *dev, dma_addr_t dma_address,
+				  size_t size,
+				  enum dma_data_direction direction)
+{
+	/* We do nothing. */
+}
 
 static inline int
 dma_map_sg(struct device *dev, struct scatterlist *sg, int nents,
@@ -284,8 +292,12 @@ dma_map_sg(struct device *dev, struct scatterlist *sg, int nents,
 	return nents;
 }
 
-/* We don't do anything here. */
-#define dma_unmap_sg(dev, sg, nents, dir)	((void)0)
+static inline void dma_unmap_sg(struct device *dev, struct scatterlist *sg,
+				int nhwentries,
+				enum dma_data_direction direction)
+{
+	/* We don't do anything here. */
+}
 
 #endif /* CONFIG_PPC64 */
 
diff --git a/include/asm-powerpc/elf.h b/include/asm-powerpc/elf.h
index de507995c7b1..e42820d6d25b 100644
--- a/include/asm-powerpc/elf.h
+++ b/include/asm-powerpc/elf.h
@@ -413,13 +413,8 @@ do {									\
 /* Notes used in ET_CORE. Note name is "SPU/<fd>/<filename>". */
 #define NT_SPU		1
 
-extern int arch_notes_size(void);
-extern void arch_write_notes(struct file *file);
-
-#define ELF_CORE_EXTRA_NOTES_SIZE arch_notes_size()
-#define ELF_CORE_WRITE_EXTRA_NOTES arch_write_notes(file)
-
 #define ARCH_HAVE_EXTRA_ELF_NOTES
-#endif /* CONFIG_PPC_CELL */
+
+#endif /* CONFIG_SPU_BASE */
 
 #endif /* _ASM_POWERPC_ELF_H */
diff --git a/include/asm-powerpc/exception.h b/include/asm-powerpc/exception.h
new file mode 100644
index 000000000000..39abdb02fdef
--- /dev/null
+++ b/include/asm-powerpc/exception.h
@@ -0,0 +1,311 @@
+#ifndef _ASM_POWERPC_EXCEPTION_H
+#define _ASM_POWERPC_EXCEPTION_H
+/*
+ * Extracted from head_64.S
+ *
+ *  PowerPC version
+ *    Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org)
+ *
+ *  Rewritten by Cort Dougan (cort@cs.nmt.edu) for PReP
+ *    Copyright (C) 1996 Cort Dougan <cort@cs.nmt.edu>
+ *  Adapted for Power Macintosh by Paul Mackerras.
+ *  Low-level exception handlers and MMU support
+ *  rewritten by Paul Mackerras.
+ *    Copyright (C) 1996 Paul Mackerras.
+ *
+ *  Adapted for 64bit PowerPC by Dave Engebretsen, Peter Bergner, and
+ *    Mike Corrigan {engebret|bergner|mikejc}@us.ibm.com
+ *
+ *  This file contains the low-level support and setup for the
+ *  PowerPC-64 platform, including trap and interrupt dispatch.
+ *
+ *  This program is free software; you can redistribute it and/or
+ *  modify it under the terms of the GNU General Public License
+ *  as published by the Free Software Foundation; either version
+ *  2 of the License, or (at your option) any later version.
+ */
+/*
+ * The following macros define the code that appears as
+ * the prologue to each of the exception handlers.  They
+ * are split into two parts to allow a single kernel binary
+ * to be used for pSeries and iSeries.
+ *
+ * We make as much of the exception code common between native
+ * exception handlers (including pSeries LPAR) and iSeries LPAR
+ * implementations as possible.
+ */
+
+#define EX_R9		0
+#define EX_R10		8
+#define EX_R11		16
+#define EX_R12		24
+#define EX_R13		32
+#define EX_SRR0		40
+#define EX_DAR		48
+#define EX_DSISR	56
+#define EX_CCR		60
+#define EX_R3		64
+#define EX_LR		72
+
+/*
+ * We're short on space and time in the exception prolog, so we can't
+ * use the normal SET_REG_IMMEDIATE macro. Normally we just need the
+ * low halfword of the address, but for Kdump we need the whole low
+ * word.
+ */
+#ifdef CONFIG_CRASH_DUMP
+#define LOAD_HANDLER(reg, label)					\
+	oris	reg,reg,(label)@h;	/* virt addr of handler ... */	\
+	ori	reg,reg,(label)@l;	/* .. and the rest */
+#else
+#define LOAD_HANDLER(reg, label)					\
+	ori	reg,reg,(label)@l;	/* virt addr of handler ... */
+#endif
+
+#define EXCEPTION_PROLOG_1(area)				\
+	mfspr	r13,SPRN_SPRG3;		/* get paca address into r13 */	\
+	std	r9,area+EX_R9(r13);	/* save r9 - r12 */		\
+	std	r10,area+EX_R10(r13);					\
+	std	r11,area+EX_R11(r13);					\
+	std	r12,area+EX_R12(r13);					\
+	mfspr	r9,SPRN_SPRG1;						\
+	std	r9,area+EX_R13(r13);					\
+	mfcr	r9
+
+/*
+ * Equal to EXCEPTION_PROLOG_PSERIES, except that it forces 64bit mode.
+ * The firmware calls the registered system_reset_fwnmi and
+ * machine_check_fwnmi handlers in 32bit mode if the cpu happens to run
+ * a 32bit application at the time of the event.
+ * This firmware bug is present on POWER4 and JS20.
+ */
+#define EXCEPTION_PROLOG_PSERIES_FORCE_64BIT(area, label)		\
+	EXCEPTION_PROLOG_1(area);					\
+	clrrdi	r12,r13,32;		/* get high part of &label */	\
+	mfmsr	r10;							\
+	/* force 64bit mode */						\
+	li	r11,5;			/* MSR_SF_LG|MSR_ISF_LG */	\
+	rldimi	r10,r11,61,0;		/* insert into top 3 bits */	\
+	/* done 64bit mode */						\
+	mfspr	r11,SPRN_SRR0;		/* save SRR0 */			\
+	LOAD_HANDLER(r12,label)						\
+	ori	r10,r10,MSR_IR|MSR_DR|MSR_RI;				\
+	mtspr	SPRN_SRR0,r12;						\
+	mfspr	r12,SPRN_SRR1;		/* and SRR1 */			\
+	mtspr	SPRN_SRR1,r10;						\
+	rfid;								\
+	b	.	/* prevent speculative execution */
+
+#define EXCEPTION_PROLOG_PSERIES(area, label)				\
+	EXCEPTION_PROLOG_1(area);					\
+	clrrdi	r12,r13,32;		/* get high part of &label */	\
+	mfmsr	r10;							\
+	mfspr	r11,SPRN_SRR0;		/* save SRR0 */			\
+	LOAD_HANDLER(r12,label)						\
+	ori	r10,r10,MSR_IR|MSR_DR|MSR_RI;				\
+	mtspr	SPRN_SRR0,r12;						\
+	mfspr	r12,SPRN_SRR1;		/* and SRR1 */			\
+	mtspr	SPRN_SRR1,r10;						\
+	rfid;								\
+	b	.	/* prevent speculative execution */
+
+/*
+ * The common exception prolog is used for all except a few exceptions
+ * such as a segment miss on a kernel address.  We have to be prepared
+ * to take another exception from the point where we first touch the
+ * kernel stack onwards.
+ *
+ * On entry r13 points to the paca, r9-r13 are saved in the paca,
+ * r9 contains the saved CR, r11 and r12 contain the saved SRR0 and
+ * SRR1, and relocation is on.
+ */
+#define EXCEPTION_PROLOG_COMMON(n, area)				   \
+	andi.	r10,r12,MSR_PR;		/* See if coming from user	*/ \
+	mr	r10,r1;			/* Save r1			*/ \
+	subi	r1,r1,INT_FRAME_SIZE;	/* alloc frame on kernel stack	*/ \
+	beq-	1f;							   \
+	ld	r1,PACAKSAVE(r13);	/* kernel stack to use		*/ \
+1:	cmpdi	cr1,r1,0;		/* check if r1 is in userspace	*/ \
+	bge-	cr1,2f;			/* abort if it is		*/ \
+	b	3f;							   \
+2:	li	r1,(n);			/* will be reloaded later	*/ \
+	sth	r1,PACA_TRAP_SAVE(r13);					   \
+	b	bad_stack;						   \
+3:	std	r9,_CCR(r1);		/* save CR in stackframe	*/ \
+	std	r11,_NIP(r1);		/* save SRR0 in stackframe	*/ \
+	std	r12,_MSR(r1);		/* save SRR1 in stackframe	*/ \
+	std	r10,0(r1);		/* make stack chain pointer	*/ \
+	std	r0,GPR0(r1);		/* save r0 in stackframe	*/ \
+	std	r10,GPR1(r1);		/* save r1 in stackframe	*/ \
+	ACCOUNT_CPU_USER_ENTRY(r9, r10);				   \
+	std	r2,GPR2(r1);		/* save r2 in stackframe	*/ \
+	SAVE_4GPRS(3, r1);		/* save r3 - r6 in stackframe	*/ \
+	SAVE_2GPRS(7, r1);		/* save r7, r8 in stackframe	*/ \
+	ld	r9,area+EX_R9(r13);	/* move r9, r10 to stackframe	*/ \
+	ld	r10,area+EX_R10(r13);					   \
+	std	r9,GPR9(r1);						   \
+	std	r10,GPR10(r1);						   \
+	ld	r9,area+EX_R11(r13);	/* move r11 - r13 to stackframe	*/ \
+	ld	r10,area+EX_R12(r13);					   \
+	ld	r11,area+EX_R13(r13);					   \
+	std	r9,GPR11(r1);						   \
+	std	r10,GPR12(r1);						   \
+	std	r11,GPR13(r1);						   \
+	ld	r2,PACATOC(r13);	/* get kernel TOC into r2	*/ \
+	mflr	r9;			/* save LR in stackframe	*/ \
+	std	r9,_LINK(r1);						   \
+	mfctr	r10;			/* save CTR in stackframe	*/ \
+	std	r10,_CTR(r1);						   \
+	lbz	r10,PACASOFTIRQEN(r13);				   \
+	mfspr	r11,SPRN_XER;		/* save XER in stackframe	*/ \
+	std	r10,SOFTE(r1);						   \
+	std	r11,_XER(r1);						   \
+	li	r9,(n)+1;						   \
+	std	r9,_TRAP(r1);		/* set trap number		*/ \
+	li	r10,0;							   \
+	ld	r11,exception_marker@toc(r2);				   \
+	std	r10,RESULT(r1);		/* clear regs->result		*/ \
+	std	r11,STACK_FRAME_OVERHEAD-16(r1); /* mark the frame	*/
+
+/*
+ * Exception vectors.
+ */
+#define STD_EXCEPTION_PSERIES(n, label)			\
+	. = n;						\
+	.globl label##_pSeries;				\
+label##_pSeries:					\
+	HMT_MEDIUM;					\
+	mtspr	SPRN_SPRG1,r13;		/* save r13 */	\
+	EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, label##_common)
+
+#define HSTD_EXCEPTION_PSERIES(n, label)		\
+	. = n;						\
+	.globl label##_pSeries;				\
+label##_pSeries:					\
+	HMT_MEDIUM;					\
+	mtspr	SPRN_SPRG1,r20;		/* save r20 */	\
+	mfspr	r20,SPRN_HSRR0;		/* copy HSRR0 to SRR0 */ \
+	mtspr	SPRN_SRR0,r20;				\
+	mfspr	r20,SPRN_HSRR1;		/* copy HSRR0 to SRR0 */ \
+	mtspr	SPRN_SRR1,r20;				\
+	mfspr	r20,SPRN_SPRG1;		/* restore r20 */ \
+	mtspr	SPRN_SPRG1,r13;		/* save r13 */	\
+	EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, label##_common)
+
+
+#define MASKABLE_EXCEPTION_PSERIES(n, label)				\
+	. = n;								\
+	.globl label##_pSeries;						\
+label##_pSeries:							\
+	HMT_MEDIUM;							\
+	mtspr	SPRN_SPRG1,r13;		/* save r13 */			\
+	mfspr	r13,SPRN_SPRG3;		/* get paca address into r13 */	\
+	std	r9,PACA_EXGEN+EX_R9(r13);	/* save r9, r10 */	\
+	std	r10,PACA_EXGEN+EX_R10(r13);				\
+	lbz	r10,PACASOFTIRQEN(r13);					\
+	mfcr	r9;							\
+	cmpwi	r10,0;							\
+	beq	masked_interrupt;					\
+	mfspr	r10,SPRN_SPRG1;						\
+	std	r10,PACA_EXGEN+EX_R13(r13);				\
+	std	r11,PACA_EXGEN+EX_R11(r13);				\
+	std	r12,PACA_EXGEN+EX_R12(r13);				\
+	clrrdi	r12,r13,32;		/* get high part of &label */	\
+	mfmsr	r10;							\
+	mfspr	r11,SPRN_SRR0;		/* save SRR0 */			\
+	LOAD_HANDLER(r12,label##_common)				\
+	ori	r10,r10,MSR_IR|MSR_DR|MSR_RI;				\
+	mtspr	SPRN_SRR0,r12;						\
+	mfspr	r12,SPRN_SRR1;		/* and SRR1 */			\
+	mtspr	SPRN_SRR1,r10;						\
+	rfid;								\
+	b	.	/* prevent speculative execution */
+
+#ifdef CONFIG_PPC_ISERIES
+#define DISABLE_INTS				\
+	li	r11,0;				\
+	stb	r11,PACASOFTIRQEN(r13);		\
+BEGIN_FW_FTR_SECTION;				\
+	stb	r11,PACAHARDIRQEN(r13);		\
+END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES);	\
+BEGIN_FW_FTR_SECTION;				\
+	mfmsr	r10;				\
+	ori	r10,r10,MSR_EE;			\
+	mtmsrd	r10,1;				\
+END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
+
+#else
+#define DISABLE_INTS				\
+	li	r11,0;				\
+	stb	r11,PACASOFTIRQEN(r13);		\
+	stb	r11,PACAHARDIRQEN(r13)
+
+#endif /* CONFIG_PPC_ISERIES */
+
+#define ENABLE_INTS				\
+	ld	r12,_MSR(r1);			\
+	mfmsr	r11;				\
+	rlwimi	r11,r12,0,MSR_EE;		\
+	mtmsrd	r11,1
+
+#define STD_EXCEPTION_COMMON(trap, label, hdlr)		\
+	.align	7;					\
+	.globl label##_common;				\
+label##_common:						\
+	EXCEPTION_PROLOG_COMMON(trap, PACA_EXGEN);	\
+	DISABLE_INTS;					\
+	bl	.save_nvgprs;				\
+	addi	r3,r1,STACK_FRAME_OVERHEAD;		\
+	bl	hdlr;					\
+	b	.ret_from_except
+
+/*
+ * Like STD_EXCEPTION_COMMON, but for exceptions that can occur
+ * in the idle task and therefore need the special idle handling.
+ */
+#define STD_EXCEPTION_COMMON_IDLE(trap, label, hdlr)	\
+	.align	7;					\
+	.globl label##_common;				\
+label##_common:						\
+	EXCEPTION_PROLOG_COMMON(trap, PACA_EXGEN);	\
+	FINISH_NAP;					\
+	DISABLE_INTS;					\
+	bl	.save_nvgprs;				\
+	addi	r3,r1,STACK_FRAME_OVERHEAD;		\
+	bl	hdlr;					\
+	b	.ret_from_except
+
+#define STD_EXCEPTION_COMMON_LITE(trap, label, hdlr)	\
+	.align	7;					\
+	.globl label##_common;				\
+label##_common:						\
+	EXCEPTION_PROLOG_COMMON(trap, PACA_EXGEN);	\
+	FINISH_NAP;					\
+	DISABLE_INTS;					\
+BEGIN_FTR_SECTION					\
+	bl	.ppc64_runlatch_on;			\
+END_FTR_SECTION_IFSET(CPU_FTR_CTRL)			\
+	addi	r3,r1,STACK_FRAME_OVERHEAD;		\
+	bl	hdlr;					\
+	b	.ret_from_except_lite
+
+/*
+ * When the idle code in power4_idle puts the CPU into NAP mode,
+ * it has to do so in a loop, and relies on the external interrupt
+ * and decrementer interrupt entry code to get it out of the loop.
+ * It sets the _TLF_NAPPING bit in current_thread_info()->local_flags
+ * to signal that it is in the loop and needs help to get out.
+ */
+#ifdef CONFIG_PPC_970_NAP
+#define FINISH_NAP				\
+BEGIN_FTR_SECTION				\
+	clrrdi	r11,r1,THREAD_SHIFT;		\
+	ld	r9,TI_LOCAL_FLAGS(r11);		\
+	andi.	r10,r9,_TLF_NAPPING;		\
+	bnel	power4_fixup_nap;		\
+END_FTR_SECTION_IFSET(CPU_FTR_CAN_NAP)
+#else
+#define FINISH_NAP
+#endif
+
+#endif	/* _ASM_POWERPC_EXCEPTION_H */
diff --git a/include/asm-powerpc/fs_pd.h b/include/asm-powerpc/fs_pd.h
index c624915b757e..9361cd5342cc 100644
--- a/include/asm-powerpc/fs_pd.h
+++ b/include/asm-powerpc/fs_pd.h
@@ -19,48 +19,22 @@
 
 #if defined(CONFIG_8260)
 #include <asm/mpc8260.h>
-#elif defined(CONFIG_85xx)
-#include <asm/mpc85xx.h>
 #endif
 
-#define cpm2_map(member)						\
-({									\
-	u32 offset = offsetof(cpm2_map_t, member);			\
-	void *addr = ioremap (CPM_MAP_ADDR + offset,			\
-			      sizeof( ((cpm2_map_t*)0)->member));	\
-	addr;								\
-})
-
-#define cpm2_map_size(member, size)					\
-({									\
-	u32 offset = offsetof(cpm2_map_t, member);			\
-	void *addr = ioremap (CPM_MAP_ADDR + offset, size);		\
-	addr;								\
-})
-
-#define cpm2_unmap(addr)	iounmap(addr)
+#define cpm2_map(member) (&cpm2_immr->member)
+#define cpm2_map_size(member, size) (&cpm2_immr->member)
+#define cpm2_unmap(addr) do {} while(0)
 #endif
 
 #ifdef CONFIG_8xx
 #include <asm/8xx_immap.h>
 #include <asm/mpc8xx.h>
 
-#define immr_map(member)						\
-({									\
-	u32 offset = offsetof(immap_t, member);				\
-	void *addr = ioremap (IMAP_ADDR + offset,			\
-			      sizeof( ((immap_t*)0)->member));		\
-	addr;								\
-})
-
-#define immr_map_size(member, size)					\
-({									\
-	u32 offset = offsetof(immap_t, member);				\
-	void *addr = ioremap (IMAP_ADDR + offset, size);		\
-	addr;								\
-})
+extern immap_t __iomem *mpc8xx_immr;
 
-#define immr_unmap(addr)		iounmap(addr)
+#define immr_map(member) (&mpc8xx_immr->member)
+#define immr_map_size(member, size) (&mpc8xx_immr->member)
+#define immr_unmap(addr) do {} while (0)
 #endif
 
 static inline int uart_baudrate(void)
diff --git a/include/asm-powerpc/highmem.h b/include/asm-powerpc/highmem.h
new file mode 100644
index 000000000000..f7b21ee302b4
--- /dev/null
+++ b/include/asm-powerpc/highmem.h
@@ -0,0 +1,135 @@
+/*
+ * highmem.h: virtual kernel memory mappings for high memory
+ *
+ * PowerPC version, stolen from the i386 version.
+ *
+ * Used in CONFIG_HIGHMEM systems for memory pages which
+ * are not addressable by direct kernel virtual addresses.
+ *
+ * Copyright (C) 1999 Gerhard Wichert, Siemens AG
+ *		      Gerhard.Wichert@pdb.siemens.de
+ *
+ *
+ * Redesigned the x86 32-bit VM architecture to deal with
+ * up to 16 Terrabyte physical memory. With current x86 CPUs
+ * we now support up to 64 Gigabytes physical RAM.
+ *
+ * Copyright (C) 1999 Ingo Molnar <mingo@redhat.com>
+ */
+
+#ifndef _ASM_HIGHMEM_H
+#define _ASM_HIGHMEM_H
+
+#ifdef __KERNEL__
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <asm/kmap_types.h>
+#include <asm/tlbflush.h>
+#include <asm/page.h>
+
+/* undef for production */
+#define HIGHMEM_DEBUG 1
+
+extern pte_t *kmap_pte;
+extern pgprot_t kmap_prot;
+extern pte_t *pkmap_page_table;
+
+/*
+ * Right now we initialize only a single pte table. It can be extended
+ * easily, subsequent pte tables have to be allocated in one physical
+ * chunk of RAM.
+ */
+#define PKMAP_BASE 	CONFIG_HIGHMEM_START
+#define LAST_PKMAP 	(1 << PTE_SHIFT)
+#define LAST_PKMAP_MASK (LAST_PKMAP-1)
+#define PKMAP_NR(virt)  ((virt-PKMAP_BASE) >> PAGE_SHIFT)
+#define PKMAP_ADDR(nr)  (PKMAP_BASE + ((nr) << PAGE_SHIFT))
+
+#define KMAP_FIX_BEGIN	(PKMAP_BASE + 0x00400000UL)
+
+extern void *kmap_high(struct page *page);
+extern void kunmap_high(struct page *page);
+
+static inline void *kmap(struct page *page)
+{
+	might_sleep();
+	if (!PageHighMem(page))
+		return page_address(page);
+	return kmap_high(page);
+}
+
+static inline void kunmap(struct page *page)
+{
+	BUG_ON(in_interrupt());
+	if (!PageHighMem(page))
+		return;
+	kunmap_high(page);
+}
+
+/*
+ * The use of kmap_atomic/kunmap_atomic is discouraged - kmap/kunmap
+ * gives a more generic (and caching) interface. But kmap_atomic can
+ * be used in IRQ contexts, so in some (very limited) cases we need
+ * it.
+ */
+static inline void *kmap_atomic(struct page *page, enum km_type type)
+{
+	unsigned int idx;
+	unsigned long vaddr;
+
+	/* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */
+	pagefault_disable();
+	if (!PageHighMem(page))
+		return page_address(page);
+
+	idx = type + KM_TYPE_NR*smp_processor_id();
+	vaddr = KMAP_FIX_BEGIN + idx * PAGE_SIZE;
+#ifdef HIGHMEM_DEBUG
+	BUG_ON(!pte_none(*(kmap_pte+idx)));
+#endif
+	set_pte_at(&init_mm, vaddr, kmap_pte+idx, mk_pte(page, kmap_prot));
+	flush_tlb_page(NULL, vaddr);
+
+	return (void*) vaddr;
+}
+
+static inline void kunmap_atomic(void *kvaddr, enum km_type type)
+{
+#ifdef HIGHMEM_DEBUG
+	unsigned long vaddr = (unsigned long) kvaddr & PAGE_MASK;
+	unsigned int idx = type + KM_TYPE_NR*smp_processor_id();
+
+	if (vaddr < KMAP_FIX_BEGIN) { // FIXME
+		pagefault_enable();
+		return;
+	}
+
+	BUG_ON(vaddr != KMAP_FIX_BEGIN + idx * PAGE_SIZE);
+
+	/*
+	 * force other mappings to Oops if they'll try to access
+	 * this pte without first remap it
+	 */
+	pte_clear(&init_mm, vaddr, kmap_pte+idx);
+	flush_tlb_page(NULL, vaddr);
+#endif
+	pagefault_enable();
+}
+
+static inline struct page *kmap_atomic_to_page(void *ptr)
+{
+	unsigned long idx, vaddr = (unsigned long) ptr;
+
+	if (vaddr < KMAP_FIX_BEGIN)
+		return virt_to_page(ptr);
+
+	idx = (vaddr - KMAP_FIX_BEGIN) >> PAGE_SHIFT;
+	return pte_page(kmap_pte[idx]);
+}
+
+#define flush_cache_kmaps()	flush_cache_all()
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASM_HIGHMEM_H */
diff --git a/include/asm-powerpc/hydra.h b/include/asm-powerpc/hydra.h
new file mode 100644
index 000000000000..1ad4eed07fbe
--- /dev/null
+++ b/include/asm-powerpc/hydra.h
@@ -0,0 +1,102 @@
+/*
+ *  include/asm-ppc/hydra.h -- Mac I/O `Hydra' definitions
+ *
+ *  Copyright (C) 1997 Geert Uytterhoeven
+ *
+ *  This file is based on the following documentation:
+ *
+ *	Macintosh Technology in the Common Hardware Reference Platform
+ *	Apple Computer, Inc.
+ *
+ *	© Copyright 1995 Apple Computer, Inc. All rights reserved.
+ *
+ *  It's available online from http://chrp.apple.com/MacTech.pdf.
+ *  You can obtain paper copies of this book from computer bookstores or by
+ *  writing Morgan Kaufmann Publishers, Inc., 340 Pine Street, Sixth Floor, San
+ *  Francisco, CA 94104. Reference ISBN 1-55860-393-X.
+ *
+ *  This file is subject to the terms and conditions of the GNU General Public
+ *  License.  See the file COPYING in the main directory of this archive
+ *  for more details.
+ */
+
+#ifndef _ASMPPC_HYDRA_H
+#define _ASMPPC_HYDRA_H
+
+#ifdef __KERNEL__
+
+struct Hydra {
+    /* DBDMA Controller Register Space */
+    char Pad1[0x30];
+    u_int CachePD;
+    u_int IDs;
+    u_int Feature_Control;
+    char Pad2[0x7fc4];
+    /* DBDMA Channel Register Space */
+    char SCSI_DMA[0x100];
+    char Pad3[0x300];
+    char SCCA_Tx_DMA[0x100];
+    char SCCA_Rx_DMA[0x100];
+    char SCCB_Tx_DMA[0x100];
+    char SCCB_Rx_DMA[0x100];
+    char Pad4[0x7800];
+    /* Device Register Space */
+    char SCSI[0x1000];
+    char ADB[0x1000];
+    char SCC_Legacy[0x1000];
+    char SCC[0x1000];
+    char Pad9[0x2000];
+    char VIA[0x2000];
+    char Pad10[0x28000];
+    char OpenPIC[0x40000];
+};
+
+extern volatile struct Hydra __iomem *Hydra;
+
+
+    /*
+     *  Feature Control Register
+     */
+
+#define HYDRA_FC_SCC_CELL_EN	0x00000001	/* Enable SCC Clock */
+#define HYDRA_FC_SCSI_CELL_EN	0x00000002	/* Enable SCSI Clock */
+#define HYDRA_FC_SCCA_ENABLE	0x00000004	/* Enable SCC A Lines */
+#define HYDRA_FC_SCCB_ENABLE	0x00000008	/* Enable SCC B Lines */
+#define HYDRA_FC_ARB_BYPASS	0x00000010	/* Bypass Internal Arbiter */
+#define HYDRA_FC_RESET_SCC	0x00000020	/* Reset SCC */
+#define HYDRA_FC_MPIC_ENABLE	0x00000040	/* Enable OpenPIC */
+#define HYDRA_FC_SLOW_SCC_PCLK	0x00000080	/* 1=15.6672, 0=25 MHz */
+#define HYDRA_FC_MPIC_IS_MASTER	0x00000100	/* OpenPIC Master Mode */
+
+
+    /*
+     *  OpenPIC Interrupt Sources
+     */
+
+#define HYDRA_INT_SIO		0
+#define HYDRA_INT_SCSI_DMA	1
+#define HYDRA_INT_SCCA_TX_DMA	2
+#define HYDRA_INT_SCCA_RX_DMA	3
+#define HYDRA_INT_SCCB_TX_DMA	4
+#define HYDRA_INT_SCCB_RX_DMA	5
+#define HYDRA_INT_SCSI		6
+#define HYDRA_INT_SCCA		7
+#define HYDRA_INT_SCCB		8
+#define HYDRA_INT_VIA		9
+#define HYDRA_INT_ADB		10
+#define HYDRA_INT_ADB_NMI	11
+#define HYDRA_INT_EXT1		12	/* PCI IRQW */
+#define HYDRA_INT_EXT2		13	/* PCI IRQX */
+#define HYDRA_INT_EXT3		14	/* PCI IRQY */
+#define HYDRA_INT_EXT4		15	/* PCI IRQZ */
+#define HYDRA_INT_EXT5		16	/* IDE Primay/Secondary */
+#define HYDRA_INT_EXT6		17	/* IDE Secondary */
+#define HYDRA_INT_EXT7		18	/* Power Off Request */
+#define HYDRA_INT_SPARE		19
+
+extern int hydra_init(void);
+extern void macio_adb_init(void);
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASMPPC_HYDRA_H */
diff --git a/include/asm-powerpc/ide.h b/include/asm-powerpc/ide.h
index 0f66f0f82c32..1644e44c8757 100644
--- a/include/asm-powerpc/ide.h
+++ b/include/asm-powerpc/ide.h
@@ -67,7 +67,7 @@ static __inline__ unsigned long ide_default_io_base(int index)
 #define ide_init_default_irq(base)	ide_default_irq(base)
 #endif
 
-#if (defined CONFIG_APUS || defined CONFIG_BLK_DEV_MPC8xx_IDE )
+#ifdef CONFIG_BLK_DEV_MPC8xx_IDE
 #define IDE_ARCH_ACK_INTR  1
 #define ide_ack_intr(hwif) (hwif->hw.ack_intr ? hwif->hw.ack_intr(hwif) : 1)
 #endif
diff --git a/include/asm-powerpc/immap_86xx.h b/include/asm-powerpc/immap_86xx.h
index 59b9e07b8e99..0ad4e653d464 100644
--- a/include/asm-powerpc/immap_86xx.h
+++ b/include/asm-powerpc/immap_86xx.h
@@ -1,124 +1,135 @@
-/*
+/**
  * MPC86xx Internal Memory Map
  *
- * Author: Jeff Brown
+ * Authors: Jeff Brown
+ *          Timur Tabi <timur@freescale.com>
  *
- * Copyright 2004 Freescale Semiconductor, Inc
+ * Copyright 2004,2007 Freescale Semiconductor, Inc
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  *
+ * This header file defines structures for various 86xx SOC devices that are
+ * used by multiple source files.
  */
 
 #ifndef __ASM_POWERPC_IMMAP_86XX_H__
 #define __ASM_POWERPC_IMMAP_86XX_H__
 #ifdef __KERNEL__
 
-/* Eventually this should define all the IO block registers in 86xx */
+/* Global Utility Registers */
+struct ccsr_guts {
+	__be32	porpllsr;	/* 0x.0000 - POR PLL Ratio Status Register */
+	__be32	porbmsr;	/* 0x.0004 - POR Boot Mode Status Register */
+	__be32	porimpscr;	/* 0x.0008 - POR I/O Impedance Status and Control Register */
+	__be32	pordevsr;	/* 0x.000c - POR I/O Device Status Register */
+	__be32	pordbgmsr;	/* 0x.0010 - POR Debug Mode Status Register */
+	u8	res1[0x20 - 0x14];
+	__be32	porcir;		/* 0x.0020 - POR Configuration Information Register */
+	u8	res2[0x30 - 0x24];
+	__be32	gpiocr;		/* 0x.0030 - GPIO Control Register */
+	u8	res3[0x40 - 0x34];
+	__be32	gpoutdr;	/* 0x.0040 - General-Purpose Output Data Register */
+	u8	res4[0x50 - 0x44];
+	__be32	gpindr;		/* 0x.0050 - General-Purpose Input Data Register */
+	u8	res5[0x60 - 0x54];
+	__be32	pmuxcr;		/* 0x.0060 - Alternate Function Signal Multiplex Control */
+	u8	res6[0x70 - 0x64];
+	__be32	devdisr;	/* 0x.0070 - Device Disable Control */
+	__be32	devdisr2;	/* 0x.0074 - Device Disable Control 2 */
+	u8	res7[0x80 - 0x78];
+	__be32	powmgtcsr;	/* 0x.0080 - Power Management Status and Control Register */
+	u8	res8[0x90 - 0x84];
+	__be32	mcpsumr;	/* 0x.0090 - Machine Check Summary Register */
+	__be32	rstrscr;	/* 0x.0094 - Reset Request Status and Control Register */
+	u8	res9[0xA0 - 0x98];
+	__be32	pvr;		/* 0x.00a0 - Processor Version Register */
+	__be32	svr;		/* 0x.00a4 - System Version Register */
+	u8	res10[0xB0 - 0xA8];
+	__be32	rstcr;		/* 0x.00b0 - Reset Control Register */
+	u8	res11[0xC0 - 0xB4];
+	__be32	elbcvselcr;	/* 0x.00c0 - eLBC Voltage Select Ctrl Reg */
+	u8	res12[0x800 - 0xC4];
+	__be32	clkdvdr;	/* 0x.0800 - Clock Divide Register */
+	u8	res13[0x900 - 0x804];
+	__be32	ircr;		/* 0x.0900 - Infrared Control Register */
+	u8	res14[0x908 - 0x904];
+	__be32	dmacr;		/* 0x.0908 - DMA Control Register */
+	u8	res15[0x914 - 0x90C];
+	__be32	elbccr;		/* 0x.0914 - eLBC Control Register */
+	u8	res16[0xB20 - 0x918];
+	__be32	ddr1clkdr;	/* 0x.0b20 - DDR1 Clock Disable Register */
+	__be32	ddr2clkdr;	/* 0x.0b24 - DDR2 Clock Disable Register */
+	__be32	ddrclkdr;	/* 0x.0b28 - DDR Clock Disable Register */
+	u8	res17[0xE00 - 0xB2C];
+	__be32	clkocr;		/* 0x.0e00 - Clock Out Select Register */
+	u8	res18[0xE10 - 0xE04];
+	__be32	ddrdllcr;	/* 0x.0e10 - DDR DLL Control Register */
+	u8	res19[0xE20 - 0xE14];
+	__be32	lbcdllcr;	/* 0x.0e20 - LBC DLL Control Register */
+	u8	res20[0xF04 - 0xE24];
+	__be32	srds1cr0;	/* 0x.0f04 - SerDes1 Control Register 0 */
+	__be32	srds1cr1;	/* 0x.0f08 - SerDes1 Control Register 0 */
+	u8	res21[0xF40 - 0xF0C];
+	__be32	srds2cr0;	/* 0x.0f40 - SerDes1 Control Register 0 */
+	__be32	srds2cr1;	/* 0x.0f44 - SerDes1 Control Register 0 */
+} __attribute__ ((packed));
 
-/* PCI Registers */
-typedef struct ccsr_pci {
-	uint	cfg_addr;	/* 0x.000 - PCI Configuration Address Register */
-	uint	cfg_data;	/* 0x.004 - PCI Configuration Data Register */
-	uint	int_ack;	/* 0x.008 - PCI Interrupt Acknowledge Register */
-	char	res1[3060];
-	uint	potar0;		/* 0x.c00 - PCI Outbound Transaction Address Register 0 */
-	uint	potear0;	/* 0x.c04 - PCI Outbound Translation Extended Address Register 0 */
-	uint	powbar0;	/* 0x.c08 - PCI Outbound Window Base Address Register 0 */
-	char	res2[4];
-	uint	powar0;		/* 0x.c10 - PCI Outbound Window Attributes Register 0 */
-	char	res3[12];
-	uint	potar1;		/* 0x.c20 - PCI Outbound Transaction Address Register 1 */
-	uint	potear1;	/* 0x.c24 - PCI Outbound Translation Extended Address Register 1 */
-	uint	powbar1;	/* 0x.c28 - PCI Outbound Window Base Address Register 1 */
-	char	res4[4];
-	uint	powar1;		/* 0x.c30 - PCI Outbound Window Attributes Register 1 */
-	char	res5[12];
-	uint	potar2;		/* 0x.c40 - PCI Outbound Transaction Address Register 2 */
-	uint	potear2;	/* 0x.c44 - PCI Outbound Translation Extended Address Register 2 */
-	uint	powbar2;	/* 0x.c48 - PCI Outbound Window Base Address Register 2 */
-	char	res6[4];
-	uint	powar2;		/* 0x.c50 - PCI Outbound Window Attributes Register 2 */
-	char	res7[12];
-	uint	potar3;		/* 0x.c60 - PCI Outbound Transaction Address Register 3 */
-	uint	potear3;	/* 0x.c64 - PCI Outbound Translation Extended Address Register 3 */
-	uint	powbar3;	/* 0x.c68 - PCI Outbound Window Base Address Register 3 */
-	char	res8[4];
-	uint	powar3;		/* 0x.c70 - PCI Outbound Window Attributes Register 3 */
-	char	res9[12];
-	uint	potar4;		/* 0x.c80 - PCI Outbound Transaction Address Register 4 */
-	uint	potear4;	/* 0x.c84 - PCI Outbound Translation Extended Address Register 4 */
-	uint	powbar4;	/* 0x.c88 - PCI Outbound Window Base Address Register 4 */
-	char	res10[4];
-	uint	powar4;		/* 0x.c90 - PCI Outbound Window Attributes Register 4 */
-	char	res11[268];
-	uint	pitar3;		/* 0x.da0 - PCI Inbound Translation Address Register 3  */
-	char	res12[4];
-	uint	piwbar3;	/* 0x.da8 - PCI Inbound Window Base Address Register 3 */
-	uint	piwbear3;	/* 0x.dac - PCI Inbound Window Base Extended Address Register 3 */
-	uint	piwar3;		/* 0x.db0 - PCI Inbound Window Attributes Register 3 */
-	char	res13[12];
-	uint	pitar2;		/* 0x.dc0 - PCI Inbound Translation Address Register 2  */
-	char	res14[4];
-	uint	piwbar2;	/* 0x.dc8 - PCI Inbound Window Base Address Register 2 */
-	uint	piwbear2;	/* 0x.dcc - PCI Inbound Window Base Extended Address Register 2 */
-	uint	piwar2;		/* 0x.dd0 - PCI Inbound Window Attributes Register 2 */
-	char	res15[12];
-	uint	pitar1;		/* 0x.de0 - PCI Inbound Translation Address Register 1  */
-	char	res16[4];
-	uint	piwbar1;	/* 0x.de8 - PCI Inbound Window Base Address Register 1 */
-	char	res17[4];
-	uint	piwar1;		/* 0x.df0 - PCI Inbound Window Attributes Register 1 */
-	char	res18[12];
-	uint	err_dr;		/* 0x.e00 - PCI Error Detect Register */
-	uint	err_cap_dr;	/* 0x.e04 - PCI Error Capture Disable Register */
-	uint	err_en;		/* 0x.e08 - PCI Error Enable Register */
-	uint	err_attrib;	/* 0x.e0c - PCI Error Attributes Capture Register */
-	uint	err_addr;	/* 0x.e10 - PCI Error Address Capture Register */
-	uint	err_ext_addr;	/* 0x.e14 - PCI Error Extended Address Capture Register */
-	uint	err_dl;		/* 0x.e18 - PCI Error Data Low Capture Register */
-	uint	err_dh;		/* 0x.e1c - PCI Error Data High Capture Register */
-	uint	gas_timr;	/* 0x.e20 - PCI Gasket Timer Register */
-	uint	pci_timr;	/* 0x.e24 - PCI Timer Register */
-	char	res19[472];
-} ccsr_pci_t;
+#define CCSR_GUTS_DMACR_DEV_SSI	0	/* DMA controller/channel set to SSI */
+#define CCSR_GUTS_DMACR_DEV_IR	1	/* DMA controller/channel set to IR */
 
-/* Global Utility Registers */
-typedef struct ccsr_guts {
-	uint	porpllsr;	/* 0x.0000 - POR PLL Ratio Status Register */
-	uint	porbmsr;	/* 0x.0004 - POR Boot Mode Status Register */
-	uint	porimpscr;	/* 0x.0008 - POR I/O Impedance Status and Control Register */
-	uint	pordevsr;	/* 0x.000c - POR I/O Device Status Register */
-	uint	pordbgmsr;	/* 0x.0010 - POR Debug Mode Status Register */
-	char	res1[12];
-	uint	gpporcr;	/* 0x.0020 - General-Purpose POR Configuration Register */
-	char	res2[12];
-	uint	gpiocr;		/* 0x.0030 - GPIO Control Register */
-	char	res3[12];
-	uint	gpoutdr;	/* 0x.0040 - General-Purpose Output Data Register */
-	char	res4[12];
-	uint	gpindr;		/* 0x.0050 - General-Purpose Input Data Register */
-	char	res5[12];
-	uint	pmuxcr;		/* 0x.0060 - Alternate Function Signal Multiplex Control */
-	char	res6[12];
-	uint	devdisr;	/* 0x.0070 - Device Disable Control */
-	char	res7[12];
-	uint	powmgtcsr;	/* 0x.0080 - Power Management Status and Control Register */
-	char	res8[12];
-	uint	mcpsumr;	/* 0x.0090 - Machine Check Summary Register */
-	char	res9[12];
-	uint	pvr;		/* 0x.00a0 - Processor Version Register */
-	uint	svr;		/* 0x.00a4 - System Version Register */
-	char	res10[3416];
-	uint	clkocr;		/* 0x.0e00 - Clock Out Select Register */
-	char	res11[12];
-	uint	ddrdllcr;	/* 0x.0e10 - DDR DLL Control Register */
-	char	res12[12];
-	uint	lbcdllcr;	/* 0x.0e20 - LBC DLL Control Register */
-	char	res13[61916];
-} ccsr_guts_t;
+/*
+ * Set the DMACR register in the GUTS
+ *
+ * The DMACR register determines the source of initiated transfers for each
+ * channel on each DMA controller.  Rather than have a bunch of repetitive
+ * macros for the bit patterns, we just have a function that calculates
+ * them.
+ *
+ * guts: Pointer to GUTS structure
+ * co: The DMA controller (1 or 2)
+ * ch: The channel on the DMA controller (0, 1, 2, or 3)
+ * device: The device to set as the source (CCSR_GUTS_DMACR_DEV_xx)
+ */
+static inline void guts_set_dmacr(struct ccsr_guts __iomem *guts,
+	unsigned int co, unsigned int ch, unsigned int device)
+{
+	unsigned int shift = 16 + (8 * (2 - co) + 2 * (3 - ch));
+
+	clrsetbits_be32(&guts->dmacr, 3 << shift, device << shift);
+}
+
+#define CCSR_GUTS_PMUXCR_LDPSEL		0x00010000
+#define CCSR_GUTS_PMUXCR_SSI1_MASK	0x0000C000	/* Bitmask for SSI1 */
+#define CCSR_GUTS_PMUXCR_SSI1_LA	0x00000000	/* Latched address */
+#define CCSR_GUTS_PMUXCR_SSI1_HI	0x00004000	/* High impedance */
+#define CCSR_GUTS_PMUXCR_SSI1_SSI	0x00008000	/* Used for SSI1 */
+#define CCSR_GUTS_PMUXCR_SSI2_MASK	0x00003000	/* Bitmask for SSI2 */
+#define CCSR_GUTS_PMUXCR_SSI2_LA	0x00000000	/* Latched address */
+#define CCSR_GUTS_PMUXCR_SSI2_HI	0x00001000	/* High impedance */
+#define CCSR_GUTS_PMUXCR_SSI2_SSI	0x00002000	/* Used for SSI2 */
+#define CCSR_GUTS_PMUXCR_LA_22_25_LA	0x00000000	/* Latched Address */
+#define CCSR_GUTS_PMUXCR_LA_22_25_HI	0x00000400	/* High impedance */
+#define CCSR_GUTS_PMUXCR_DBGDRV		0x00000200	/* Signals not driven */
+#define CCSR_GUTS_PMUXCR_DMA2_0		0x00000008
+#define CCSR_GUTS_PMUXCR_DMA2_3		0x00000004
+#define CCSR_GUTS_PMUXCR_DMA1_0		0x00000002
+#define CCSR_GUTS_PMUXCR_DMA1_3		0x00000001
+
+#define CCSR_GUTS_CLKDVDR_PXCKEN	0x80000000
+#define CCSR_GUTS_CLKDVDR_SSICKEN	0x20000000
+#define CCSR_GUTS_CLKDVDR_PXCKINV	0x10000000
+#define CCSR_GUTS_CLKDVDR_PXCKDLY_SHIFT 25
+#define CCSR_GUTS_CLKDVDR_PXCKDLY_MASK	0x06000000
+#define CCSR_GUTS_CLKDVDR_PXCKDLY(x) \
+	(((x) & 3) << CCSR_GUTS_CLKDVDR_PXCKDLY_SHIFT)
+#define CCSR_GUTS_CLKDVDR_PXCLK_SHIFT	16
+#define CCSR_GUTS_CLKDVDR_PXCLK_MASK	0x001F0000
+#define CCSR_GUTS_CLKDVDR_PXCLK(x) (((x) & 31) << CCSR_GUTS_CLKDVDR_PXCLK_SHIFT)
+#define CCSR_GUTS_CLKDVDR_SSICLK_MASK	0x000000FF
+#define CCSR_GUTS_CLKDVDR_SSICLK(x) ((x) & CCSR_GUTS_CLKDVDR_SSICLK_MASK)
 
 #endif /* __ASM_POWERPC_IMMAP_86XX_H__ */
 #endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/immap_cpm2.h b/include/asm-powerpc/immap_cpm2.h
new file mode 100644
index 000000000000..4080bab0468c
--- /dev/null
+++ b/include/asm-powerpc/immap_cpm2.h
@@ -0,0 +1,650 @@
+/*
+ * CPM2 Internal Memory Map
+ * Copyright (c) 1999 Dan Malek (dmalek@jlc.net)
+ *
+ * The Internal Memory Map for devices with CPM2 on them.  This
+ * is the superset of all CPM2 devices (8260, 8266, 8280, 8272,
+ * 8560).
+ */
+#ifdef __KERNEL__
+#ifndef __IMMAP_CPM2__
+#define __IMMAP_CPM2__
+
+#include <linux/types.h>
+
+/* System configuration registers.
+*/
+typedef	struct sys_82xx_conf {
+	u32	sc_siumcr;
+	u32	sc_sypcr;
+	u8	res1[6];
+	u16	sc_swsr;
+	u8	res2[20];
+	u32	sc_bcr;
+	u8	sc_ppc_acr;
+	u8	res3[3];
+	u32	sc_ppc_alrh;
+	u32	sc_ppc_alrl;
+	u8	sc_lcl_acr;
+	u8	res4[3];
+	u32	sc_lcl_alrh;
+	u32	sc_lcl_alrl;
+	u32	sc_tescr1;
+	u32	sc_tescr2;
+	u32	sc_ltescr1;
+	u32	sc_ltescr2;
+	u32	sc_pdtea;
+	u8	sc_pdtem;
+	u8	res5[3];
+	u32	sc_ldtea;
+	u8	sc_ldtem;
+	u8	res6[163];
+} sysconf_82xx_cpm2_t;
+
+typedef	struct sys_85xx_conf {
+	u32	sc_cear;
+	u16	sc_ceer;
+	u16	sc_cemr;
+	u8	res1[70];
+	u32	sc_smaer;
+	u8	res2[4];
+	u32	sc_smevr;
+	u32	sc_smctr;
+	u32	sc_lmaer;
+	u8	res3[4];
+	u32	sc_lmevr;
+	u32	sc_lmctr;
+	u8	res4[144];
+} sysconf_85xx_cpm2_t;
+
+typedef union sys_conf {
+	sysconf_82xx_cpm2_t	siu_82xx;
+	sysconf_85xx_cpm2_t	siu_85xx;
+} sysconf_cpm2_t;
+
+
+
+/* Memory controller registers.
+*/
+typedef struct	mem_ctlr {
+	u32	memc_br0;
+	u32	memc_or0;
+	u32	memc_br1;
+	u32	memc_or1;
+	u32	memc_br2;
+	u32	memc_or2;
+	u32	memc_br3;
+	u32	memc_or3;
+	u32	memc_br4;
+	u32	memc_or4;
+	u32	memc_br5;
+	u32	memc_or5;
+	u32	memc_br6;
+	u32	memc_or6;
+	u32	memc_br7;
+	u32	memc_or7;
+	u32	memc_br8;
+	u32	memc_or8;
+	u32	memc_br9;
+	u32	memc_or9;
+	u32	memc_br10;
+	u32	memc_or10;
+	u32	memc_br11;
+	u32	memc_or11;
+	u8	res1[8];
+	u32	memc_mar;
+	u8	res2[4];
+	u32	memc_mamr;
+	u32	memc_mbmr;
+	u32	memc_mcmr;
+	u8	res3[8];
+	u16	memc_mptpr;
+	u8	res4[2];
+	u32	memc_mdr;
+	u8	res5[4];
+	u32	memc_psdmr;
+	u32	memc_lsdmr;
+	u8	memc_purt;
+	u8	res6[3];
+	u8	memc_psrt;
+	u8	res7[3];
+	u8	memc_lurt;
+	u8	res8[3];
+	u8	memc_lsrt;
+	u8	res9[3];
+	u32	memc_immr;
+	u32	memc_pcibr0;
+	u32	memc_pcibr1;
+	u8	res10[16];
+	u32	memc_pcimsk0;
+	u32	memc_pcimsk1;
+	u8	res11[52];
+} memctl_cpm2_t;
+
+/* System Integration Timers.
+*/
+typedef struct	sys_int_timers {
+	u8	res1[32];
+	u16	sit_tmcntsc;
+	u8	res2[2];
+	u32	sit_tmcnt;
+	u8	res3[4];
+	u32	sit_tmcntal;
+	u8	res4[16];
+	u16	sit_piscr;
+	u8	res5[2];
+	u32	sit_pitc;
+	u32	sit_pitr;
+	u8      res6[94];
+	u8	res7[390];
+} sit_cpm2_t;
+
+#define PISCR_PIRQ_MASK		((u16)0xff00)
+#define PISCR_PS		((u16)0x0080)
+#define PISCR_PIE		((u16)0x0004)
+#define PISCR_PTF		((u16)0x0002)
+#define PISCR_PTE		((u16)0x0001)
+
+/* PCI Controller.
+*/
+typedef struct pci_ctlr {
+	u32	pci_omisr;
+	u32	pci_omimr;
+	u8	res1[8];
+	u32	pci_ifqpr;
+	u32	pci_ofqpr;
+	u8	res2[8];
+	u32	pci_imr0;
+	u32	pci_imr1;
+	u32	pci_omr0;
+	u32	pci_omr1;
+	u32	pci_odr;
+	u8	res3[4];
+	u32	pci_idr;
+	u8	res4[20];
+	u32	pci_imisr;
+	u32	pci_imimr;
+	u8	res5[24];
+	u32	pci_ifhpr;
+	u8	res6[4];
+	u32	pci_iftpr;
+	u8	res7[4];
+	u32	pci_iphpr;
+	u8	res8[4];
+	u32	pci_iptpr;
+	u8	res9[4];
+	u32	pci_ofhpr;
+	u8	res10[4];
+	u32	pci_oftpr;
+	u8	res11[4];
+	u32	pci_ophpr;
+	u8	res12[4];
+	u32	pci_optpr;
+	u8	res13[8];
+	u32	pci_mucr;
+	u8	res14[8];
+	u32	pci_qbar;
+	u8	res15[12];
+	u32	pci_dmamr0;
+	u32	pci_dmasr0;
+	u32	pci_dmacdar0;
+	u8	res16[4];
+	u32	pci_dmasar0;
+	u8	res17[4];
+	u32	pci_dmadar0;
+	u8	res18[4];
+	u32	pci_dmabcr0;
+	u32	pci_dmandar0;
+	u8	res19[86];
+	u32	pci_dmamr1;
+	u32	pci_dmasr1;
+	u32	pci_dmacdar1;
+	u8	res20[4];
+	u32	pci_dmasar1;
+	u8	res21[4];
+	u32	pci_dmadar1;
+	u8	res22[4];
+	u32	pci_dmabcr1;
+	u32	pci_dmandar1;
+	u8	res23[88];
+	u32	pci_dmamr2;
+	u32	pci_dmasr2;
+	u32	pci_dmacdar2;
+	u8	res24[4];
+	u32	pci_dmasar2;
+	u8	res25[4];
+	u32	pci_dmadar2;
+	u8	res26[4];
+	u32	pci_dmabcr2;
+	u32	pci_dmandar2;
+	u8	res27[88];
+	u32	pci_dmamr3;
+	u32	pci_dmasr3;
+	u32	pci_dmacdar3;
+	u8	res28[4];
+	u32	pci_dmasar3;
+	u8	res29[4];
+	u32	pci_dmadar3;
+	u8	res30[4];
+	u32	pci_dmabcr3;
+	u32	pci_dmandar3;
+	u8	res31[344];
+	u32	pci_potar0;
+	u8	res32[4];
+	u32	pci_pobar0;
+	u8	res33[4];
+	u32	pci_pocmr0;
+	u8	res34[4];
+	u32	pci_potar1;
+	u8	res35[4];
+	u32	pci_pobar1;
+	u8	res36[4];
+	u32	pci_pocmr1;
+	u8	res37[4];
+	u32	pci_potar2;
+	u8	res38[4];
+	u32	pci_pobar2;
+	u8	res39[4];
+	u32	pci_pocmr2;
+	u8	res40[50];
+	u32	pci_ptcr;
+	u32	pci_gpcr;
+	u32	pci_gcr;
+	u32	pci_esr;
+	u32	pci_emr;
+	u32	pci_ecr;
+	u32	pci_eacr;
+	u8	res41[4];
+	u32	pci_edcr;
+	u8	res42[4];
+	u32	pci_eccr;
+	u8	res43[44];
+	u32	pci_pitar1;
+	u8	res44[4];
+	u32	pci_pibar1;
+	u8	res45[4];
+	u32	pci_picmr1;
+	u8	res46[4];
+	u32	pci_pitar0;
+	u8	res47[4];
+	u32	pci_pibar0;
+	u8	res48[4];
+	u32	pci_picmr0;
+	u8	res49[4];
+	u32	pci_cfg_addr;
+	u32	pci_cfg_data;
+	u32	pci_int_ack;
+	u8	res50[756];
+} pci_cpm2_t;
+
+/* Interrupt Controller.
+*/
+typedef struct interrupt_controller {
+	u16	ic_sicr;
+	u8	res1[2];
+	u32	ic_sivec;
+	u32	ic_sipnrh;
+	u32	ic_sipnrl;
+	u32	ic_siprr;
+	u32	ic_scprrh;
+	u32	ic_scprrl;
+	u32	ic_simrh;
+	u32	ic_simrl;
+	u32	ic_siexr;
+	u8	res2[88];
+} intctl_cpm2_t;
+
+/* Clocks and Reset.
+*/
+typedef struct clk_and_reset {
+	u32	car_sccr;
+	u8	res1[4];
+	u32	car_scmr;
+	u8	res2[4];
+	u32	car_rsr;
+	u32	car_rmr;
+	u8	res[104];
+} car_cpm2_t;
+
+/* Input/Output Port control/status registers.
+ * Names consistent with processor manual, although they are different
+ * from the original 8xx names.......
+ */
+typedef struct io_port {
+	u32	iop_pdira;
+	u32	iop_ppara;
+	u32	iop_psora;
+	u32	iop_podra;
+	u32	iop_pdata;
+	u8	res1[12];
+	u32	iop_pdirb;
+	u32	iop_pparb;
+	u32	iop_psorb;
+	u32	iop_podrb;
+	u32	iop_pdatb;
+	u8	res2[12];
+	u32	iop_pdirc;
+	u32	iop_pparc;
+	u32	iop_psorc;
+	u32	iop_podrc;
+	u32	iop_pdatc;
+	u8	res3[12];
+	u32	iop_pdird;
+	u32	iop_ppard;
+	u32	iop_psord;
+	u32	iop_podrd;
+	u32	iop_pdatd;
+	u8	res4[12];
+} iop_cpm2_t;
+
+/* Communication Processor Module Timers
+*/
+typedef struct cpm_timers {
+	u8	cpmt_tgcr1;
+	u8	res1[3];
+	u8	cpmt_tgcr2;
+	u8	res2[11];
+	u16	cpmt_tmr1;
+	u16	cpmt_tmr2;
+	u16	cpmt_trr1;
+	u16	cpmt_trr2;
+	u16	cpmt_tcr1;
+	u16	cpmt_tcr2;
+	u16	cpmt_tcn1;
+	u16	cpmt_tcn2;
+	u16	cpmt_tmr3;
+	u16	cpmt_tmr4;
+	u16	cpmt_trr3;
+	u16	cpmt_trr4;
+	u16	cpmt_tcr3;
+	u16	cpmt_tcr4;
+	u16	cpmt_tcn3;
+	u16	cpmt_tcn4;
+	u16	cpmt_ter1;
+	u16	cpmt_ter2;
+	u16	cpmt_ter3;
+	u16	cpmt_ter4;
+	u8	res3[584];
+} cpmtimer_cpm2_t;
+
+/* DMA control/status registers.
+*/
+typedef struct sdma_csr {
+	u8	res0[24];
+	u8	sdma_sdsr;
+	u8	res1[3];
+	u8	sdma_sdmr;
+	u8	res2[3];
+	u8	sdma_idsr1;
+	u8	res3[3];
+	u8	sdma_idmr1;
+	u8	res4[3];
+	u8	sdma_idsr2;
+	u8	res5[3];
+	u8	sdma_idmr2;
+	u8	res6[3];
+	u8	sdma_idsr3;
+	u8	res7[3];
+	u8	sdma_idmr3;
+	u8	res8[3];
+	u8	sdma_idsr4;
+	u8	res9[3];
+	u8	sdma_idmr4;
+	u8	res10[707];
+} sdma_cpm2_t;
+
+/* Fast controllers
+*/
+typedef struct fcc {
+	u32	fcc_gfmr;
+	u32	fcc_fpsmr;
+	u16	fcc_ftodr;
+	u8	res1[2];
+	u16	fcc_fdsr;
+	u8	res2[2];
+	u16	fcc_fcce;
+	u8	res3[2];
+	u16	fcc_fccm;
+	u8	res4[2];
+	u8	fcc_fccs;
+	u8	res5[3];
+	u8	fcc_ftirr_phy[4];
+} fcc_t;
+
+/* Fast controllers continued
+ */
+typedef struct fcc_c {
+	u32	fcc_firper;
+	u32	fcc_firer;
+	u32	fcc_firsr_hi;
+	u32	fcc_firsr_lo;
+	u8	fcc_gfemr;
+	u8	res1[15];
+} fcc_c_t;
+
+/* TC Layer
+ */
+typedef struct tclayer {
+	u16	tc_tcmode;
+	u16	tc_cdsmr;
+	u16	tc_tcer;
+	u16	tc_rcc;
+	u16	tc_tcmr;
+	u16	tc_fcc;
+	u16	tc_ccc;
+	u16	tc_icc;
+	u16	tc_tcc;
+	u16	tc_ecc;
+	u8	res1[12];
+} tclayer_t;
+
+
+/* I2C
+*/
+typedef struct i2c {
+	u8	i2c_i2mod;
+	u8	res1[3];
+	u8	i2c_i2add;
+	u8	res2[3];
+	u8	i2c_i2brg;
+	u8	res3[3];
+	u8	i2c_i2com;
+	u8	res4[3];
+	u8	i2c_i2cer;
+	u8	res5[3];
+	u8	i2c_i2cmr;
+	u8	res6[331];
+} i2c_cpm2_t;
+
+typedef struct scc {		/* Serial communication channels */
+	u32	scc_gsmrl;
+	u32	scc_gsmrh;
+	u16	scc_psmr;
+	u8	res1[2];
+	u16	scc_todr;
+	u16	scc_dsr;
+	u16	scc_scce;
+	u8	res2[2];
+	u16	scc_sccm;
+	u8	res3;
+	u8	scc_sccs;
+	u8	res4[8];
+} scc_t;
+
+typedef struct smc {		/* Serial management channels */
+	u8	res1[2];
+	u16	smc_smcmr;
+	u8	res2[2];
+	u8	smc_smce;
+	u8	res3[3];
+	u8	smc_smcm;
+	u8	res4[5];
+} smc_t;
+
+/* Serial Peripheral Interface.
+*/
+typedef struct spi_ctrl {
+	u16	spi_spmode;
+	u8	res1[4];
+	u8	spi_spie;
+	u8	res2[3];
+	u8	spi_spim;
+	u8	res3[2];
+	u8	spi_spcom;
+	u8	res4[82];
+} spictl_cpm2_t;
+
+/* CPM Mux.
+*/
+typedef struct cpmux {
+	u8	cmx_si1cr;
+	u8	res1;
+	u8	cmx_si2cr;
+	u8	res2;
+	u32	cmx_fcr;
+	u32	cmx_scr;
+	u8	cmx_smr;
+	u8	res3;
+	u16	cmx_uar;
+	u8	res4[16];
+} cpmux_t;
+
+/* SIRAM control
+*/
+typedef struct siram {
+	u16	si_amr;
+	u16	si_bmr;
+	u16	si_cmr;
+	u16	si_dmr;
+	u8	si_gmr;
+	u8	res1;
+	u8	si_cmdr;
+	u8	res2;
+	u8	si_str;
+	u8	res3;
+	u16	si_rsr;
+} siramctl_t;
+
+typedef struct mcc {
+	u16	mcc_mcce;
+	u8	res1[2];
+	u16	mcc_mccm;
+	u8	res2[2];
+	u8	mcc_mccf;
+	u8	res3[7];
+} mcc_t;
+
+typedef struct comm_proc {
+	u32	cp_cpcr;
+	u32	cp_rccr;
+	u8	res1[14];
+	u16	cp_rter;
+	u8	res2[2];
+	u16	cp_rtmr;
+	u16	cp_rtscr;
+	u8	res3[2];
+	u32	cp_rtsr;
+	u8	res4[12];
+} cpm_cpm2_t;
+
+/* USB Controller.
+*/
+typedef struct usb_ctlr {
+	u8	usb_usmod;
+	u8	usb_usadr;
+	u8	usb_uscom;
+	u8	res1[1];
+	u16	usb_usep1;
+	u16	usb_usep2;
+	u16	usb_usep3;
+	u16	usb_usep4;
+	u8	res2[4];
+	u16	usb_usber;
+	u8	res3[2];
+	u16	usb_usbmr;
+	u8	usb_usbs;
+	u8	res4[7];
+} usb_cpm2_t;
+
+/* ...and the whole thing wrapped up....
+*/
+
+typedef struct immap {
+	/* Some references are into the unique and known dpram spaces,
+	 * others are from the generic base.
+	 */
+#define im_dprambase	im_dpram1
+	u8		im_dpram1[16*1024];
+	u8		res1[16*1024];
+	u8		im_dpram2[4*1024];
+	u8		res2[8*1024];
+	u8		im_dpram3[4*1024];
+	u8		res3[16*1024];
+
+	sysconf_cpm2_t	im_siu_conf;	/* SIU Configuration */
+	memctl_cpm2_t	im_memctl;	/* Memory Controller */
+	sit_cpm2_t	im_sit;		/* System Integration Timers */
+	pci_cpm2_t	im_pci;		/* PCI Controller */
+	intctl_cpm2_t	im_intctl;	/* Interrupt Controller */
+	car_cpm2_t	im_clkrst;	/* Clocks and reset */
+	iop_cpm2_t	im_ioport;	/* IO Port control/status */
+	cpmtimer_cpm2_t	im_cpmtimer;	/* CPM timers */
+	sdma_cpm2_t	im_sdma;	/* SDMA control/status */
+
+	fcc_t		im_fcc[3];	/* Three FCCs */
+	u8		res4z[32];
+	fcc_c_t		im_fcc_c[3];	/* Continued FCCs */
+
+	u8		res4[32];
+
+	tclayer_t	im_tclayer[8];	/* Eight TCLayers */
+	u16		tc_tcgsr;
+	u16		tc_tcger;
+
+	/* First set of baud rate generators.
+	*/
+	u8		res[236];
+	u32		im_brgc5;
+	u32		im_brgc6;
+	u32		im_brgc7;
+	u32		im_brgc8;
+
+	u8		res5[608];
+
+	i2c_cpm2_t	im_i2c;		/* I2C control/status */
+	cpm_cpm2_t	im_cpm;		/* Communication processor */
+
+	/* Second set of baud rate generators.
+	*/
+	u32		im_brgc1;
+	u32		im_brgc2;
+	u32		im_brgc3;
+	u32		im_brgc4;
+
+	scc_t		im_scc[4];	/* Four SCCs */
+	smc_t		im_smc[2];	/* Couple of SMCs */
+	spictl_cpm2_t	im_spi;		/* A SPI */
+	cpmux_t		im_cpmux;	/* CPM clock route mux */
+	siramctl_t	im_siramctl1;	/* First SI RAM Control */
+	mcc_t		im_mcc1;	/* First MCC */
+	siramctl_t	im_siramctl2;	/* Second SI RAM Control */
+	mcc_t		im_mcc2;	/* Second MCC */
+	usb_cpm2_t	im_usb;		/* USB Controller */
+
+	u8		res6[1153];
+
+	u16		im_si1txram[256];
+	u8		res7[512];
+	u16		im_si1rxram[256];
+	u8		res8[512];
+	u16		im_si2txram[256];
+	u8		res9[512];
+	u16		im_si2rxram[256];
+	u8		res10[512];
+	u8		res11[4096];
+} cpm2_map_t;
+
+extern cpm2_map_t __iomem *cpm2_immr;
+
+#endif /* __IMMAP_CPM2__ */
+#endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/immap_qe.h b/include/asm-powerpc/immap_qe.h
index 1020b7fc0129..aba9806b31c9 100644
--- a/include/asm-powerpc/immap_qe.h
+++ b/include/asm-powerpc/immap_qe.h
@@ -86,8 +86,9 @@ struct cp_qe {
 	__be16	ceexe4;		/* QE external request 4 event register */
 	u8	res11[0x2];
 	__be16	ceexm4;		/* QE external request 4 mask register */
-	u8	res12[0x2];
-	u8	res13[0x280];
+	u8	res12[0x3A];
+	__be32	ceurnr;		/* QE microcode revision number register */
+	u8	res13[0x244];
 } __attribute__ ((packed));
 
 /* QE Multiplexer */
@@ -96,10 +97,7 @@ struct qe_mux {
 	__be32	cmxsi1cr_l;	/* CMX SI1 clock route low register */
 	__be32	cmxsi1cr_h;	/* CMX SI1 clock route high register */
 	__be32	cmxsi1syr;	/* CMX SI1 SYNC route register */
-	__be32	cmxucr1;	/* CMX UCC1, UCC3 clock route register */
-	__be32	cmxucr2;	/* CMX UCC5, UCC7 clock route register */
-	__be32	cmxucr3;	/* CMX UCC2, UCC4 clock route register */
-	__be32	cmxucr4;	/* CMX UCC6, UCC8 clock route register */
+	__be32	cmxucr[4];	/* CMX UCCx clock route registers */
 	__be32	cmxupcr;	/* CMX UPC clock route register */
 	u8	res0[0x1C];
 } __attribute__ ((packed));
@@ -260,7 +258,6 @@ struct ucc_slow {
 	__be16	utpt;
 	u8	res4[0x52];
 	u8	guemr;		/* UCC general extended mode register */
-	u8	res5[0x200 - 0x091];
 } __attribute__ ((packed));
 
 /* QE UCC Fast */
@@ -293,21 +290,13 @@ struct ucc_fast {
 	__be32	urtry;		/* UCC retry counter register */
 	u8	res8[0x4C];
 	u8	guemr;		/* UCC general extended mode register */
-	u8	res9[0x100 - 0x091];
-} __attribute__ ((packed));
-
-/* QE UCC */
-struct ucc_common {
-	u8	res1[0x90];
-	u8	guemr;
-	u8	res2[0x200 - 0x091];
 } __attribute__ ((packed));
 
 struct ucc {
 	union {
 		struct	ucc_slow slow;
 		struct	ucc_fast fast;
-		struct	ucc_common common;
+		u8	res[0x200];	/* UCC blocks are 512 bytes each */
 	};
 } __attribute__ ((packed));
 
@@ -406,7 +395,7 @@ struct dbg {
 
 /* RISC Special Registers (Trap and Breakpoint) */
 struct rsp {
-	u8	fixme[0x100];
+	u32	reg[0x40];	/* 64 32-bit registers */
 } __attribute__ ((packed));
 
 struct qe_immap {
@@ -435,11 +424,13 @@ struct qe_immap {
 	u8			res13[0x600];
 	struct upc		upc2;		/* MultiPHY UTOPIA POS Ctrlr 2*/
 	struct sdma		sdma;		/* SDMA */
-	struct dbg		dbg;		/* Debug Space */
-	struct rsp		rsp[0x2];	/* RISC Special Registers
+	struct dbg		dbg;		/* 0x104080 - 0x1040FF
+						   Debug Space */
+	struct rsp		rsp[0x2];	/* 0x104100 - 0x1042FF
+						   RISC Special Registers
 						   (Trap and Breakpoint) */
-	u8			res14[0x300];
-	u8			res15[0x3A00];
+	u8			res14[0x300];	/* 0x104300 - 0x1045FF */
+	u8			res15[0x3A00];	/* 0x104600 - 0x107FFF */
 	u8			res16[0x8000];	/* 0x108000 - 0x110000 */
 	u8			muram[0xC000];	/* 0x110000 - 0x11C000
 						   Multi-user RAM */
@@ -450,7 +441,7 @@ struct qe_immap {
 extern struct qe_immap *qe_immr;
 extern phys_addr_t get_qe_base(void);
 
-static inline unsigned long immrbar_virt_to_phys(volatile void * address)
+static inline unsigned long immrbar_virt_to_phys(void *address)
 {
 	if ( ((u32)address >= (u32)qe_immr) &&
 			((u32)address < ((u32)qe_immr + QE_IMMAP_SIZE)) )
diff --git a/include/asm-powerpc/io.h b/include/asm-powerpc/io.h
index bb8d965f96c6..affba7052fb6 100644
--- a/include/asm-powerpc/io.h
+++ b/include/asm-powerpc/io.h
@@ -86,7 +86,7 @@ extern unsigned long pci_dram_offset;
  */
 
 #ifdef CONFIG_PPC64
-#define IO_SET_SYNC_FLAG()	do { get_paca()->io_sync = 1; } while(0)
+#define IO_SET_SYNC_FLAG()	do { local_paca->io_sync = 1; } while(0)
 #else
 #define IO_SET_SYNC_FLAG()
 #endif
@@ -734,6 +734,32 @@ static inline void * bus_to_virt(unsigned long address)
 #define setbits16(_addr, _v) out_be16((_addr), in_be16(_addr) |  (_v))
 #define clrbits16(_addr, _v) out_be16((_addr), in_be16(_addr) & ~(_v))
 
+#define setbits8(_addr, _v) out_8((_addr), in_8(_addr) |  (_v))
+#define clrbits8(_addr, _v) out_8((_addr), in_8(_addr) & ~(_v))
+
+/* Clear and set bits in one shot.  These macros can be used to clear and
+ * set multiple bits in a register using a single read-modify-write.  These
+ * macros can also be used to set a multiple-bit bit pattern using a mask,
+ * by specifying the mask in the 'clear' parameter and the new bit pattern
+ * in the 'set' parameter.
+ */
+
+#define clrsetbits(type, addr, clear, set) \
+	out_##type((addr), (in_##type(addr) & ~(clear)) | (set))
+
+#ifdef __powerpc64__
+#define clrsetbits_be64(addr, clear, set) clrsetbits(be64, addr, clear, set)
+#define clrsetbits_le64(addr, clear, set) clrsetbits(le64, addr, clear, set)
+#endif
+
+#define clrsetbits_be32(addr, clear, set) clrsetbits(be32, addr, clear, set)
+#define clrsetbits_le32(addr, clear, set) clrsetbits(le32, addr, clear, set)
+
+#define clrsetbits_be16(addr, clear, set) clrsetbits(be16, addr, clear, set)
+#define clrsetbits_le16(addr, clear, set) clrsetbits(le32, addr, clear, set)
+
+#define clrsetbits_8(addr, clear, set) clrsetbits(8, addr, clear, set)
+
 #endif /* __KERNEL__ */
 
 #endif /* _ASM_POWERPC_IO_H */
diff --git a/include/asm-powerpc/irq.h b/include/asm-powerpc/irq.h
index 0485c53db2b5..1392db456523 100644
--- a/include/asm-powerpc/irq.h
+++ b/include/asm-powerpc/irq.h
@@ -124,6 +124,9 @@ struct irq_host {
 	struct irq_host_ops	*ops;
 	void			*host_data;
 	irq_hw_number_t		inval_irq;
+
+	/* Optional device node pointer */
+	struct device_node	*of_node;
 };
 
 /* The main irq map itself is an array of NR_IRQ entries containing the
@@ -142,7 +145,7 @@ extern irq_hw_number_t virq_to_hw(unsigned int virq);
 
 /**
  * irq_alloc_host - Allocate a new irq_host data structure
- * @node: device-tree node of the interrupt controller
+ * @of_node: optional device-tree node of the interrupt controller
  * @revmap_type: type of reverse mapping to use
  * @revmap_arg: for IRQ_HOST_MAP_LINEAR linear only: size of the map
  * @ops: map/unmap host callbacks
@@ -156,7 +159,8 @@ extern irq_hw_number_t virq_to_hw(unsigned int virq);
  * later during boot automatically (the reverse mapping will use the slow path
  * until that happens).
  */
-extern struct irq_host *irq_alloc_host(unsigned int revmap_type,
+extern struct irq_host *irq_alloc_host(struct device_node *of_node,
+				       unsigned int revmap_type,
 				       unsigned int revmap_arg,
 				       struct irq_host_ops *ops,
 				       irq_hw_number_t inval_irq);
diff --git a/include/asm-powerpc/iseries/hv_call_event.h b/include/asm-powerpc/iseries/hv_call_event.h
index 4cec4762076d..cc029d388e11 100644
--- a/include/asm-powerpc/iseries/hv_call_event.h
+++ b/include/asm-powerpc/iseries/hv_call_event.h
@@ -21,6 +21,9 @@
 #ifndef _ASM_POWERPC_ISERIES_HV_CALL_EVENT_H
 #define _ASM_POWERPC_ISERIES_HV_CALL_EVENT_H
 
+#include <linux/types.h>
+#include <linux/dma-mapping.h>
+
 #include <asm/iseries/hv_call_sc.h>
 #include <asm/iseries/hv_types.h>
 #include <asm/abs_addr.h>
@@ -113,6 +116,13 @@ static inline HvLpEvent_Rc HvCallEvent_signalLpEventFast(HvLpIndex targetLp,
 			eventData3, eventData4, eventData5);
 }
 
+extern void *iseries_hv_alloc(size_t size, dma_addr_t *dma_handle, gfp_t flag);
+extern void iseries_hv_free(size_t size, void *vaddr, dma_addr_t dma_handle);
+extern dma_addr_t iseries_hv_map(void *vaddr, size_t size,
+			enum dma_data_direction direction);
+extern void iseries_hv_unmap(dma_addr_t dma_handle, size_t size,
+			enum dma_data_direction direction);
+
 static inline HvLpEvent_Rc HvCallEvent_ackLpEvent(struct HvLpEvent *event)
 {
 	return HvCall1(HvCallEventAckLpEvent, virt_to_abs(event));
diff --git a/include/asm-powerpc/iseries/iommu.h b/include/asm-powerpc/iseries/iommu.h
index 6e323a13ac30..c59ee7e4bed1 100644
--- a/include/asm-powerpc/iseries/iommu.h
+++ b/include/asm-powerpc/iseries/iommu.h
@@ -22,6 +22,7 @@
  */
 
 struct pci_dev;
+struct vio_dev;
 struct device_node;
 struct iommu_table;
 
@@ -34,4 +35,7 @@ extern void iommu_table_getparms_iSeries(unsigned long busno,
 		unsigned char slotno, unsigned char virtbus,
 		struct iommu_table *tbl);
 
+extern struct iommu_table *vio_build_iommu_table_iseries(struct vio_dev *dev);
+extern void iommu_vio_init(void);
+
 #endif /* _ASM_POWERPC_ISERIES_IOMMU_H */
diff --git a/include/asm-powerpc/iseries/lpar_map.h b/include/asm-powerpc/iseries/lpar_map.h
index 2ec384d66abb..5e9f3e128ee2 100644
--- a/include/asm-powerpc/iseries/lpar_map.h
+++ b/include/asm-powerpc/iseries/lpar_map.h
@@ -22,6 +22,8 @@
 
 #include <asm/types.h>
 
+#endif
+
 /*
  * The iSeries hypervisor will set up mapping for one or more
  * ESID/VSID pairs (in SLB/segment registers) and will set up
@@ -56,6 +58,7 @@
 /* Hypervisor initially maps 32MB of the load area */
 #define HvPagesToMap	8192
 
+#ifndef __ASSEMBLY__
 struct LparMap {
 	u64	xNumberEsids;	// Number of ESID/VSID pairs
 	u64	xNumberRanges;	// Number of VA ranges to map
diff --git a/include/asm-powerpc/iseries/vio.h b/include/asm-powerpc/iseries/vio.h
index 7a95d296abd1..f9ac0d00b951 100644
--- a/include/asm-powerpc/iseries/vio.h
+++ b/include/asm-powerpc/iseries/vio.h
@@ -51,6 +51,116 @@
  */
 #define VIO_MAX_SUBTYPES 8
 
+#define VIOMAXBLOCKDMA	12
+
+struct open_data {
+	u64	disk_size;
+	u16	max_disk;
+	u16	cylinders;
+	u16	tracks;
+	u16	sectors;
+	u16	bytes_per_sector;
+};
+
+struct rw_data {
+	u64	offset;
+	struct {
+		u32	token;
+		u32	reserved;
+		u64	len;
+	} dma_info[VIOMAXBLOCKDMA];
+};
+
+struct vioblocklpevent {
+	struct HvLpEvent	event;
+	u32			reserved;
+	u16			version;
+	u16			sub_result;
+	u16			disk;
+	u16			flags;
+	union {
+		struct open_data	open_data;
+		struct rw_data		rw_data;
+		u64			changed;
+	} u;
+};
+
+#define vioblockflags_ro   0x0001
+
+enum vioblocksubtype {
+	vioblockopen = 0x0001,
+	vioblockclose = 0x0002,
+	vioblockread = 0x0003,
+	vioblockwrite = 0x0004,
+	vioblockflush = 0x0005,
+	vioblockcheck = 0x0007
+};
+
+struct viocdlpevent {
+	struct HvLpEvent	event;
+	u32			reserved;
+	u16			version;
+	u16			sub_result;
+	u16			disk;
+	u16			flags;
+	u32			token;
+	u64			offset;		/* On open, max number of disks */
+	u64			len;		/* On open, size of the disk */
+	u32			block_size;	/* Only set on open */
+	u32			media_size;	/* Only set on open */
+};
+
+enum viocdsubtype {
+	viocdopen = 0x0001,
+	viocdclose = 0x0002,
+	viocdread = 0x0003,
+	viocdwrite = 0x0004,
+	viocdlockdoor = 0x0005,
+	viocdgetinfo = 0x0006,
+	viocdcheck = 0x0007
+};
+
+struct viotapelpevent {
+	struct HvLpEvent event;
+	u32 reserved;
+	u16 version;
+	u16 sub_type_result;
+	u16 tape;
+	u16 flags;
+	u32 token;
+	u64 len;
+	union {
+		struct {
+			u32 tape_op;
+			u32 count;
+		} op;
+		struct {
+			u32 type;
+			u32 resid;
+			u32 dsreg;
+			u32 gstat;
+			u32 erreg;
+			u32 file_no;
+			u32 block_no;
+		} get_status;
+		struct {
+			u32 block_no;
+		} get_pos;
+	} u;
+};
+
+enum viotapesubtype {
+	viotapeopen = 0x0001,
+	viotapeclose = 0x0002,
+	viotaperead = 0x0003,
+	viotapewrite = 0x0004,
+	viotapegetinfo = 0x0005,
+	viotapeop = 0x0006,
+	viotapegetpos = 0x0007,
+	viotapesetpos = 0x0008,
+	viotapegetstatus = 0x0009
+};
+
 /*
  * Each subtype can register a handler to process their events.
  * The handler must have this interface.
@@ -68,6 +178,8 @@ extern void vio_set_hostlp(void);
 extern void *vio_get_event_buffer(int subtype);
 extern void vio_free_event_buffer(int subtype, void *buffer);
 
+extern struct vio_dev *vio_create_viodasd(u32 unit);
+
 extern HvLpIndex viopath_hostLp;
 extern HvLpIndex viopath_ourLp;
 
@@ -150,8 +262,4 @@ enum viochar_rc {
 	viochar_rc_ebusy = 1
 };
 
-struct device;
-
-extern struct device *iSeries_vio_dev;
-
 #endif /* _ASM_POWERPC_ISERIES_VIO_H */
diff --git a/include/asm-powerpc/kgdb.h b/include/asm-powerpc/kgdb.h
new file mode 100644
index 000000000000..b617dac82969
--- /dev/null
+++ b/include/asm-powerpc/kgdb.h
@@ -0,0 +1,57 @@
+/*
+ * kgdb.h: Defines and declarations for serial line source level
+ *         remote debugging of the Linux kernel using gdb.
+ *
+ * PPC Mods (C) 1998 Michael Tesch (tesch@cs.wisc.edu)
+ *
+ * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ */
+#ifdef __KERNEL__
+#ifndef _PPC_KGDB_H
+#define _PPC_KGDB_H
+
+#ifndef __ASSEMBLY__
+
+/* Things specific to the gen550 backend. */
+struct uart_port;
+
+extern void gen550_progress(char *, unsigned short);
+extern void gen550_kgdb_map_scc(void);
+extern void gen550_init(int, struct uart_port *);
+
+/* Things specific to the pmac backend. */
+extern void zs_kgdb_hook(int tty_num);
+
+/* To init the kgdb engine. (called by serial hook)*/
+extern void set_debug_traps(void);
+
+/* To enter the debugger explicitly. */
+extern void breakpoint(void);
+
+/* For taking exceptions
+ * these are defined in traps.c
+ */
+extern int (*debugger)(struct pt_regs *regs);
+extern int (*debugger_bpt)(struct pt_regs *regs);
+extern int (*debugger_sstep)(struct pt_regs *regs);
+extern int (*debugger_iabr_match)(struct pt_regs *regs);
+extern int (*debugger_dabr_match)(struct pt_regs *regs);
+extern void (*debugger_fault_handler)(struct pt_regs *regs);
+
+/* What we bring to the party */
+int kgdb_bpt(struct pt_regs *regs);
+int kgdb_sstep(struct pt_regs *regs);
+void kgdb(struct pt_regs *regs);
+int kgdb_iabr_match(struct pt_regs *regs);
+int kgdb_dabr_match(struct pt_regs *regs);
+
+/*
+ * external low-level support routines (ie macserial.c)
+ */
+extern void kgdb_interruptible(int); /* control interrupts from serial */
+extern void putDebugChar(char);   /* write a single character      */
+extern char getDebugChar(void);   /* read and return a single char */
+
+#endif /* !(__ASSEMBLY__) */
+#endif /* !(_PPC_KGDB_H) */
+#endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/lmb.h b/include/asm-powerpc/lmb.h
index 0c5880f70225..b5f9f4c9c294 100644
--- a/include/asm-powerpc/lmb.h
+++ b/include/asm-powerpc/lmb.h
@@ -1,5 +1,5 @@
-#ifndef _PPC64_LMB_H
-#define _PPC64_LMB_H
+#ifndef _ASM_POWERPC_LMB_H
+#define _ASM_POWERPC_LMB_H
 #ifdef __KERNEL__
 
 /*
@@ -77,4 +77,4 @@ lmb_end_pfn(struct lmb_region *type, unsigned long region_nr)
 }
 
 #endif /* __KERNEL__ */
-#endif /* _PPC64_LMB_H */
+#endif /* _ASM_POWERPC_LMB_H */
diff --git a/include/asm-powerpc/machdep.h b/include/asm-powerpc/machdep.h
index 71c6e7eb2a26..6968f4300dca 100644
--- a/include/asm-powerpc/machdep.h
+++ b/include/asm-powerpc/machdep.h
@@ -51,22 +51,22 @@ struct machdep_calls {
 #ifdef CONFIG_PPC64
 	void            (*hpte_invalidate)(unsigned long slot,
 					   unsigned long va,
-					   int psize,
+					   int psize, int ssize,
 					   int local);
 	long		(*hpte_updatepp)(unsigned long slot, 
 					 unsigned long newpp, 
 					 unsigned long va,
-					 int pize,
+					 int psize, int ssize,
 					 int local);
 	void            (*hpte_updateboltedpp)(unsigned long newpp, 
 					       unsigned long ea,
-					       int psize);
+					       int psize, int ssize);
 	long		(*hpte_insert)(unsigned long hpte_group,
 				       unsigned long va,
 				       unsigned long prpn,
 				       unsigned long rflags,
 				       unsigned long vflags,
-				       int psize);
+				       int psize, int ssize);
 	long		(*hpte_remove)(unsigned long hpte_group);
 	void		(*flush_hash_range)(unsigned long number, int local);
 
@@ -99,7 +99,7 @@ struct machdep_calls {
 #endif /* CONFIG_PPC64 */
 
 	int		(*probe)(void);
-	void		(*setup_arch)(void);
+	void		(*setup_arch)(void); /* Optional, may be NULL */
 	void		(*init_early)(void);
 	/* Optional, may be NULL. */
 	void		(*show_cpuinfo)(struct seq_file *m);
diff --git a/include/asm-powerpc/mmu-40x.h b/include/asm-powerpc/mmu-40x.h
new file mode 100644
index 000000000000..7d37f77043ac
--- /dev/null
+++ b/include/asm-powerpc/mmu-40x.h
@@ -0,0 +1,65 @@
+#ifndef _ASM_POWERPC_MMU_40X_H_
+#define _ASM_POWERPC_MMU_40X_H_
+
+/*
+ * PPC40x support
+ */
+
+#define PPC40X_TLB_SIZE 64
+
+/*
+ * TLB entries are defined by a "high" tag portion and a "low" data
+ * portion.  On all architectures, the data portion is 32-bits.
+ *
+ * TLB entries are managed entirely under software control by reading,
+ * writing, and searchoing using the 4xx-specific tlbre, tlbwr, and tlbsx
+ * instructions.
+ */
+
+#define	TLB_LO          1
+#define	TLB_HI          0
+
+#define	TLB_DATA        TLB_LO
+#define	TLB_TAG         TLB_HI
+
+/* Tag portion */
+
+#define TLB_EPN_MASK    0xFFFFFC00      /* Effective Page Number */
+#define TLB_PAGESZ_MASK 0x00000380
+#define TLB_PAGESZ(x)   (((x) & 0x7) << 7)
+#define   PAGESZ_1K		0
+#define   PAGESZ_4K             1
+#define   PAGESZ_16K            2
+#define   PAGESZ_64K            3
+#define   PAGESZ_256K           4
+#define   PAGESZ_1M             5
+#define   PAGESZ_4M             6
+#define   PAGESZ_16M            7
+#define TLB_VALID       0x00000040      /* Entry is valid */
+
+/* Data portion */
+
+#define TLB_RPN_MASK    0xFFFFFC00      /* Real Page Number */
+#define TLB_PERM_MASK   0x00000300
+#define TLB_EX          0x00000200      /* Instruction execution allowed */
+#define TLB_WR          0x00000100      /* Writes permitted */
+#define TLB_ZSEL_MASK   0x000000F0
+#define TLB_ZSEL(x)     (((x) & 0xF) << 4)
+#define TLB_ATTR_MASK   0x0000000F
+#define TLB_W           0x00000008      /* Caching is write-through */
+#define TLB_I           0x00000004      /* Caching is inhibited */
+#define TLB_M           0x00000002      /* Memory is coherent */
+#define TLB_G           0x00000001      /* Memory is guarded from prefetch */
+
+#ifndef __ASSEMBLY__
+
+typedef unsigned long phys_addr_t;
+
+typedef struct {
+	unsigned long id;
+	unsigned long vdso_base;
+} mm_context_t;
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* _ASM_POWERPC_MMU_40X_H_ */
diff --git a/include/asm-powerpc/mmu-hash64.h b/include/asm-powerpc/mmu-hash64.h
index 3112ad14ad95..82328dec2b52 100644
--- a/include/asm-powerpc/mmu-hash64.h
+++ b/include/asm-powerpc/mmu-hash64.h
@@ -47,6 +47,8 @@ extern char initial_stab[];
 
 /* Bits in the SLB VSID word */
 #define SLB_VSID_SHIFT		12
+#define SLB_VSID_SHIFT_1T	24
+#define SLB_VSID_SSIZE_SHIFT	62
 #define SLB_VSID_B		ASM_CONST(0xc000000000000000)
 #define SLB_VSID_B_256M		ASM_CONST(0x0000000000000000)
 #define SLB_VSID_B_1T		ASM_CONST(0x4000000000000000)
@@ -66,6 +68,7 @@ extern char initial_stab[];
 #define SLB_VSID_USER		(SLB_VSID_KP|SLB_VSID_KS|SLB_VSID_C)
 
 #define SLBIE_C			(0x08000000)
+#define SLBIE_SSIZE_SHIFT	25
 
 /*
  * Hash table
@@ -77,7 +80,7 @@ extern char initial_stab[];
 #define HPTE_V_AVPN_SHIFT	7
 #define HPTE_V_AVPN		ASM_CONST(0x3fffffffffffff80)
 #define HPTE_V_AVPN_VAL(x)	(((x) & HPTE_V_AVPN) >> HPTE_V_AVPN_SHIFT)
-#define HPTE_V_COMPARE(x,y)	(!(((x) ^ (y)) & HPTE_V_AVPN))
+#define HPTE_V_COMPARE(x,y)	(!(((x) ^ (y)) & 0xffffffffffffff80))
 #define HPTE_V_BOLTED		ASM_CONST(0x0000000000000010)
 #define HPTE_V_LOCK		ASM_CONST(0x0000000000000008)
 #define HPTE_V_LARGE		ASM_CONST(0x0000000000000004)
@@ -164,16 +167,19 @@ struct mmu_psize_def
 #define MMU_SEGSIZE_256M	0
 #define MMU_SEGSIZE_1T		1
 
+
 #ifndef __ASSEMBLY__
 
 /*
- * The current system page sizes
+ * The current system page and segment sizes
  */
 extern struct mmu_psize_def mmu_psize_defs[MMU_PAGE_COUNT];
 extern int mmu_linear_psize;
 extern int mmu_virtual_psize;
 extern int mmu_vmalloc_psize;
 extern int mmu_io_psize;
+extern int mmu_kernel_ssize;
+extern int mmu_highuser_ssize;
 
 /*
  * If the processor supports 64k normal pages but not 64k cache
@@ -195,13 +201,15 @@ extern int mmu_huge_psize;
  * This function sets the AVPN and L fields of the HPTE  appropriately
  * for the page size
  */
-static inline unsigned long hpte_encode_v(unsigned long va, int psize)
+static inline unsigned long hpte_encode_v(unsigned long va, int psize,
+					  int ssize)
 {
-	unsigned long v =
+	unsigned long v;
 	v = (va >> 23) & ~(mmu_psize_defs[psize].avpnm);
 	v <<= HPTE_V_AVPN_SHIFT;
 	if (psize != MMU_PAGE_4K)
 		v |= HPTE_V_LARGE;
+	v |= ((unsigned long) ssize) << HPTE_V_SSIZE_SHIFT;
 	return v;
 }
 
@@ -226,20 +234,40 @@ static inline unsigned long hpte_encode_r(unsigned long pa, int psize)
 }
 
 /*
- * This hashes a virtual address for a 256Mb segment only for now
+ * Build a VA given VSID, EA and segment size
  */
+static inline unsigned long hpt_va(unsigned long ea, unsigned long vsid,
+				   int ssize)
+{
+	if (ssize == MMU_SEGSIZE_256M)
+		return (vsid << 28) | (ea & 0xfffffffUL);
+	return (vsid << 40) | (ea & 0xffffffffffUL);
+}
 
-static inline unsigned long hpt_hash(unsigned long va, unsigned int shift)
+/*
+ * This hashes a virtual address
+ */
+
+static inline unsigned long hpt_hash(unsigned long va, unsigned int shift,
+				     int ssize)
 {
-	return ((va >> 28) & 0x7fffffffffUL) ^ ((va & 0x0fffffffUL) >> shift);
+	unsigned long hash, vsid;
+
+	if (ssize == MMU_SEGSIZE_256M) {
+		hash = (va >> 28) ^ ((va & 0x0fffffffUL) >> shift);
+	} else {
+		vsid = va >> 40;
+		hash = vsid ^ (vsid << 25) ^ ((va & 0xffffffffffUL) >> shift);
+	}
+	return hash & 0x7fffffffffUL;
 }
 
 extern int __hash_page_4K(unsigned long ea, unsigned long access,
 			  unsigned long vsid, pte_t *ptep, unsigned long trap,
-			  unsigned int local);
+			  unsigned int local, int ssize);
 extern int __hash_page_64K(unsigned long ea, unsigned long access,
 			   unsigned long vsid, pte_t *ptep, unsigned long trap,
-			   unsigned int local);
+			   unsigned int local, int ssize);
 struct mm_struct;
 extern int hash_page(unsigned long ea, unsigned long access, unsigned long trap);
 extern int hash_huge_page(struct mm_struct *mm, unsigned long access,
@@ -248,7 +276,7 @@ extern int hash_huge_page(struct mm_struct *mm, unsigned long access,
 
 extern int htab_bolt_mapping(unsigned long vstart, unsigned long vend,
 			     unsigned long pstart, unsigned long mode,
-			     int psize);
+			     int psize, int ssize);
 
 extern void htab_initialize(void);
 extern void htab_initialize_secondary(void);
@@ -256,6 +284,7 @@ extern void hpte_init_native(void);
 extern void hpte_init_lpar(void);
 extern void hpte_init_iSeries(void);
 extern void hpte_init_beat(void);
+extern void hpte_init_beat_v3(void);
 
 extern void stabs_alloc(void);
 extern void slb_initialize(void);
@@ -316,12 +345,17 @@ extern void slb_vmalloc_update(void);
  * which are used by the iSeries firmware.
  */
 
-#define VSID_MULTIPLIER	ASM_CONST(200730139)	/* 28-bit prime */
-#define VSID_BITS	36
-#define VSID_MODULUS	((1UL<<VSID_BITS)-1)
+#define VSID_MULTIPLIER_256M	ASM_CONST(200730139)	/* 28-bit prime */
+#define VSID_BITS_256M		36
+#define VSID_MODULUS_256M	((1UL<<VSID_BITS_256M)-1)
 
-#define CONTEXT_BITS	19
-#define USER_ESID_BITS	16
+#define VSID_MULTIPLIER_1T	ASM_CONST(12538073)	/* 24-bit prime */
+#define VSID_BITS_1T		24
+#define VSID_MODULUS_1T		((1UL<<VSID_BITS_1T)-1)
+
+#define CONTEXT_BITS		19
+#define USER_ESID_BITS		16
+#define USER_ESID_BITS_1T	4
 
 #define USER_VSID_RANGE	(1UL << (USER_ESID_BITS + SID_SHIFT))
 
@@ -335,17 +369,17 @@ extern void slb_vmalloc_update(void);
  *	rx = scratch register (clobbered)
  *
  * 	- rt and rx must be different registers
- * 	- The answer will end up in the low 36 bits of rt.  The higher
+ * 	- The answer will end up in the low VSID_BITS bits of rt.  The higher
  * 	  bits may contain other garbage, so you may need to mask the
  * 	  result.
  */
-#define ASM_VSID_SCRAMBLE(rt, rx)	\
-	lis	rx,VSID_MULTIPLIER@h;					\
-	ori	rx,rx,VSID_MULTIPLIER@l;				\
+#define ASM_VSID_SCRAMBLE(rt, rx, size)					\
+	lis	rx,VSID_MULTIPLIER_##size@h;				\
+	ori	rx,rx,VSID_MULTIPLIER_##size@l;				\
 	mulld	rt,rt,rx;		/* rt = rt * MULTIPLIER */	\
 									\
-	srdi	rx,rt,VSID_BITS;					\
-	clrldi	rt,rt,(64-VSID_BITS);					\
+	srdi	rx,rt,VSID_BITS_##size;					\
+	clrldi	rt,rt,(64-VSID_BITS_##size);				\
 	add	rt,rt,rx;		/* add high and low bits */	\
 	/* Now, r3 == VSID (mod 2^36-1), and lies between 0 and		\
 	 * 2^36-1+2^28-1.  That in particular means that if r3 >=	\
@@ -354,7 +388,7 @@ extern void slb_vmalloc_update(void);
 	 * doesn't, the answer is the low 36 bits of r3+1.  So in all	\
 	 * cases the answer is the low 36 bits of (r3 + ((r3+1) >> 36))*/\
 	addi	rx,rt,1;						\
-	srdi	rx,rx,VSID_BITS;	/* extract 2^36 bit */		\
+	srdi	rx,rx,VSID_BITS_##size;	/* extract 2^VSID_BITS bit */	\
 	add	rt,rt,rx
 
 
@@ -376,37 +410,60 @@ typedef struct {
 } mm_context_t;
 
 
-static inline unsigned long vsid_scramble(unsigned long protovsid)
-{
 #if 0
-	/* The code below is equivalent to this function for arguments
-	 * < 2^VSID_BITS, which is all this should ever be called
-	 * with.  However gcc is not clever enough to compute the
-	 * modulus (2^n-1) without a second multiply. */
-	return ((protovsid * VSID_MULTIPLIER) % VSID_MODULUS);
-#else /* 1 */
-	unsigned long x;
+/*
+ * The code below is equivalent to this function for arguments
+ * < 2^VSID_BITS, which is all this should ever be called
+ * with.  However gcc is not clever enough to compute the
+ * modulus (2^n-1) without a second multiply.
+ */
+#define vsid_scrample(protovsid, size) \
+	((((protovsid) * VSID_MULTIPLIER_##size) % VSID_MODULUS_##size))
 
-	x = protovsid * VSID_MULTIPLIER;
-	x = (x >> VSID_BITS) + (x & VSID_MODULUS);
-	return (x + ((x+1) >> VSID_BITS)) & VSID_MODULUS;
+#else /* 1 */
+#define vsid_scramble(protovsid, size) \
+	({								 \
+		unsigned long x;					 \
+		x = (protovsid) * VSID_MULTIPLIER_##size;		 \
+		x = (x >> VSID_BITS_##size) + (x & VSID_MODULUS_##size); \
+		(x + ((x+1) >> VSID_BITS_##size)) & VSID_MODULUS_##size; \
+	})
 #endif /* 1 */
-}
 
 /* This is only valid for addresses >= KERNELBASE */
-static inline unsigned long get_kernel_vsid(unsigned long ea)
+static inline unsigned long get_kernel_vsid(unsigned long ea, int ssize)
 {
-	return vsid_scramble(ea >> SID_SHIFT);
+	if (ssize == MMU_SEGSIZE_256M)
+		return vsid_scramble(ea >> SID_SHIFT, 256M);
+	return vsid_scramble(ea >> SID_SHIFT_1T, 1T);
 }
 
-/* This is only valid for user addresses (which are below 2^41) */
-static inline unsigned long get_vsid(unsigned long context, unsigned long ea)
+/* Returns the segment size indicator for a user address */
+static inline int user_segment_size(unsigned long addr)
 {
-	return vsid_scramble((context << USER_ESID_BITS)
-			     | (ea >> SID_SHIFT));
+	/* Use 1T segments if possible for addresses >= 1T */
+	if (addr >= (1UL << SID_SHIFT_1T))
+		return mmu_highuser_ssize;
+	return MMU_SEGSIZE_256M;
 }
 
-#define VSID_SCRAMBLE(pvsid)	(((pvsid) * VSID_MULTIPLIER) % VSID_MODULUS)
+/* This is only valid for user addresses (which are below 2^44) */
+static inline unsigned long get_vsid(unsigned long context, unsigned long ea,
+				     int ssize)
+{
+	if (ssize == MMU_SEGSIZE_256M)
+		return vsid_scramble((context << USER_ESID_BITS)
+				     | (ea >> SID_SHIFT), 256M);
+	return vsid_scramble((context << USER_ESID_BITS_1T)
+			     | (ea >> SID_SHIFT_1T), 1T);
+}
+
+/*
+ * This is only used on legacy iSeries in lparmap.c,
+ * hence the 256MB segment assumption.
+ */
+#define VSID_SCRAMBLE(pvsid)	(((pvsid) * VSID_MULTIPLIER_256M) %	\
+				 VSID_MODULUS_256M)
 #define KERNEL_VSID(ea)		VSID_SCRAMBLE(GET_ESID(ea))
 
 /* Physical address used by some IO functions */
diff --git a/include/asm-powerpc/mmu.h b/include/asm-powerpc/mmu.h
index d44d211e7588..4c0e1b4f975c 100644
--- a/include/asm-powerpc/mmu.h
+++ b/include/asm-powerpc/mmu.h
@@ -8,6 +8,9 @@
 #elif defined(CONFIG_PPC_STD_MMU)
 /* 32-bit classic hash table MMU */
 #  include <asm/mmu-hash32.h>
+#elif defined(CONFIG_40x)
+/* 40x-style software loaded TLB */
+#  include <asm/mmu-40x.h>
 #elif defined(CONFIG_44x)
 /* 44x-style software loaded TLB */
 #  include <asm/mmu-44x.h>
diff --git a/include/asm-powerpc/mpc52xx.h b/include/asm-powerpc/mpc52xx.h
index c4631f6dd4f9..24751df791ac 100644
--- a/include/asm-powerpc/mpc52xx.h
+++ b/include/asm-powerpc/mpc52xx.h
@@ -243,7 +243,7 @@ struct mpc52xx_cdm {
 
 extern void __iomem * mpc52xx_find_and_map(const char *);
 extern unsigned int mpc52xx_find_ipb_freq(struct device_node *node);
-extern void mpc52xx_setup_cpu(void);
+extern void mpc5200_setup_xlb_arbiter(void);
 extern void mpc52xx_declare_of_platform_devices(void);
 
 extern void mpc52xx_init_irq(void);
@@ -262,6 +262,16 @@ struct mpc52xx_suspend {
 extern struct mpc52xx_suspend mpc52xx_suspend;
 extern int __init mpc52xx_pm_init(void);
 extern int mpc52xx_set_wakeup_gpio(u8 pin, u8 level);
+
+#ifdef CONFIG_PPC_LITE5200
+extern int __init lite5200_pm_init(void);
+
+/* lite5200 calls mpc5200 suspend functions, so here they are */
+extern int mpc52xx_pm_prepare(suspend_state_t);
+extern int mpc52xx_pm_enter(suspend_state_t);
+extern int mpc52xx_pm_finish(suspend_state_t);
+extern char saved_sram[0x4000]; /* reuse buffer from mpc52xx suspend */
+#endif
 #endif /* CONFIG_PM */
 
 #endif /* __ASM_POWERPC_MPC52xx_H__ */
diff --git a/include/asm-powerpc/mpc52xx_psc.h b/include/asm-powerpc/mpc52xx_psc.h
new file mode 100644
index 000000000000..26690d2b32f5
--- /dev/null
+++ b/include/asm-powerpc/mpc52xx_psc.h
@@ -0,0 +1,191 @@
+/*
+ * include/asm-ppc/mpc52xx_psc.h
+ *
+ * Definitions of consts/structs to drive the Freescale MPC52xx OnChip
+ * PSCs. Theses are shared between multiple drivers since a PSC can be
+ * UART, AC97, IR, I2S, ... So this header is in asm-ppc.
+ *
+ *
+ * Maintainer : Sylvain Munaut <tnt@246tNt.com>
+ *
+ * Based/Extracted from some header of the 2.4 originally written by
+ * Dale Farnsworth <dfarnsworth@mvista.com>
+ *
+ * Copyright (C) 2004 Sylvain Munaut <tnt@246tNt.com>
+ * Copyright (C) 2003 MontaVista, Software, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef __ASM_MPC52xx_PSC_H__
+#define __ASM_MPC52xx_PSC_H__
+
+#include <asm/types.h>
+
+/* Max number of PSCs */
+#define MPC52xx_PSC_MAXNUM	6
+
+/* Programmable Serial Controller (PSC) status register bits */
+#define MPC52xx_PSC_SR_CDE	0x0080
+#define MPC52xx_PSC_SR_RXRDY	0x0100
+#define MPC52xx_PSC_SR_RXFULL	0x0200
+#define MPC52xx_PSC_SR_TXRDY	0x0400
+#define MPC52xx_PSC_SR_TXEMP	0x0800
+#define MPC52xx_PSC_SR_OE	0x1000
+#define MPC52xx_PSC_SR_PE	0x2000
+#define MPC52xx_PSC_SR_FE	0x4000
+#define MPC52xx_PSC_SR_RB	0x8000
+
+/* PSC Command values */
+#define MPC52xx_PSC_RX_ENABLE		0x0001
+#define MPC52xx_PSC_RX_DISABLE		0x0002
+#define MPC52xx_PSC_TX_ENABLE		0x0004
+#define MPC52xx_PSC_TX_DISABLE		0x0008
+#define MPC52xx_PSC_SEL_MODE_REG_1	0x0010
+#define MPC52xx_PSC_RST_RX		0x0020
+#define MPC52xx_PSC_RST_TX		0x0030
+#define MPC52xx_PSC_RST_ERR_STAT	0x0040
+#define MPC52xx_PSC_RST_BRK_CHG_INT	0x0050
+#define MPC52xx_PSC_START_BRK		0x0060
+#define MPC52xx_PSC_STOP_BRK		0x0070
+
+/* PSC TxRx FIFO status bits */
+#define MPC52xx_PSC_RXTX_FIFO_ERR	0x0040
+#define MPC52xx_PSC_RXTX_FIFO_UF	0x0020
+#define MPC52xx_PSC_RXTX_FIFO_OF	0x0010
+#define MPC52xx_PSC_RXTX_FIFO_FR	0x0008
+#define MPC52xx_PSC_RXTX_FIFO_FULL	0x0004
+#define MPC52xx_PSC_RXTX_FIFO_ALARM	0x0002
+#define MPC52xx_PSC_RXTX_FIFO_EMPTY	0x0001
+
+/* PSC interrupt mask bits */
+#define MPC52xx_PSC_IMR_TXRDY		0x0100
+#define MPC52xx_PSC_IMR_RXRDY		0x0200
+#define MPC52xx_PSC_IMR_DB		0x0400
+#define MPC52xx_PSC_IMR_IPC		0x8000
+
+/* PSC input port change bit */
+#define MPC52xx_PSC_CTS			0x01
+#define MPC52xx_PSC_DCD			0x02
+#define MPC52xx_PSC_D_CTS		0x10
+#define MPC52xx_PSC_D_DCD		0x20
+
+/* PSC mode fields */
+#define MPC52xx_PSC_MODE_5_BITS			0x00
+#define MPC52xx_PSC_MODE_6_BITS			0x01
+#define MPC52xx_PSC_MODE_7_BITS			0x02
+#define MPC52xx_PSC_MODE_8_BITS			0x03
+#define MPC52xx_PSC_MODE_BITS_MASK		0x03
+#define MPC52xx_PSC_MODE_PAREVEN		0x00
+#define MPC52xx_PSC_MODE_PARODD			0x04
+#define MPC52xx_PSC_MODE_PARFORCE		0x08
+#define MPC52xx_PSC_MODE_PARNONE		0x10
+#define MPC52xx_PSC_MODE_ERR			0x20
+#define MPC52xx_PSC_MODE_FFULL			0x40
+#define MPC52xx_PSC_MODE_RXRTS			0x80
+
+#define MPC52xx_PSC_MODE_ONE_STOP_5_BITS	0x00
+#define MPC52xx_PSC_MODE_ONE_STOP		0x07
+#define MPC52xx_PSC_MODE_TWO_STOP		0x0f
+
+#define MPC52xx_PSC_RFNUM_MASK	0x01ff
+
+
+/* Structure of the hardware registers */
+struct mpc52xx_psc {
+	u8		mode;		/* PSC + 0x00 */
+	u8		reserved0[3];
+	union {				/* PSC + 0x04 */
+		u16	status;
+		u16	clock_select;
+	} sr_csr;
+#define mpc52xx_psc_status	sr_csr.status
+#define mpc52xx_psc_clock_select sr_csr.clock_select
+	u16		reserved1;
+	u8		command;	/* PSC + 0x08 */
+	u8		reserved2[3];
+	union {				/* PSC + 0x0c */
+		u8	buffer_8;
+		u16	buffer_16;
+		u32	buffer_32;
+	} buffer;
+#define mpc52xx_psc_buffer_8	buffer.buffer_8
+#define mpc52xx_psc_buffer_16	buffer.buffer_16
+#define mpc52xx_psc_buffer_32	buffer.buffer_32
+	union {				/* PSC + 0x10 */
+		u8	ipcr;
+		u8	acr;
+	} ipcr_acr;
+#define mpc52xx_psc_ipcr	ipcr_acr.ipcr
+#define mpc52xx_psc_acr		ipcr_acr.acr
+	u8		reserved3[3];
+	union {				/* PSC + 0x14 */
+		u16	isr;
+		u16	imr;
+	} isr_imr;
+#define mpc52xx_psc_isr		isr_imr.isr
+#define mpc52xx_psc_imr		isr_imr.imr
+	u16		reserved4;
+	u8		ctur;		/* PSC + 0x18 */
+	u8		reserved5[3];
+	u8		ctlr;		/* PSC + 0x1c */
+	u8		reserved6[3];
+	u16		ccr;		/* PSC + 0x20 */
+	u8		reserved7[14];
+	u8		ivr;		/* PSC + 0x30 */
+	u8		reserved8[3];
+	u8		ip;		/* PSC + 0x34 */
+	u8		reserved9[3];
+	u8		op1;		/* PSC + 0x38 */
+	u8		reserved10[3];
+	u8		op0;		/* PSC + 0x3c */
+	u8		reserved11[3];
+	u32		sicr;		/* PSC + 0x40 */
+	u8		ircr1;		/* PSC + 0x44 */
+	u8		reserved13[3];
+	u8		ircr2;		/* PSC + 0x44 */
+	u8		reserved14[3];
+	u8		irsdr;		/* PSC + 0x4c */
+	u8		reserved15[3];
+	u8		irmdr;		/* PSC + 0x50 */
+	u8		reserved16[3];
+	u8		irfdr;		/* PSC + 0x54 */
+	u8		reserved17[3];
+	u16		rfnum;		/* PSC + 0x58 */
+	u16		reserved18;
+	u16		tfnum;		/* PSC + 0x5c */
+	u16		reserved19;
+	u32		rfdata;		/* PSC + 0x60 */
+	u16		rfstat;		/* PSC + 0x64 */
+	u16		reserved20;
+	u8		rfcntl;		/* PSC + 0x68 */
+	u8		reserved21[5];
+	u16		rfalarm;	/* PSC + 0x6e */
+	u16		reserved22;
+	u16		rfrptr;		/* PSC + 0x72 */
+	u16		reserved23;
+	u16		rfwptr;		/* PSC + 0x76 */
+	u16		reserved24;
+	u16		rflrfptr;	/* PSC + 0x7a */
+	u16		reserved25;
+	u16		rflwfptr;	/* PSC + 0x7e */
+	u32		tfdata;		/* PSC + 0x80 */
+	u16		tfstat;		/* PSC + 0x84 */
+	u16		reserved26;
+	u8		tfcntl;		/* PSC + 0x88 */
+	u8		reserved27[5];
+	u16		tfalarm;	/* PSC + 0x8e */
+	u16		reserved28;
+	u16		tfrptr;		/* PSC + 0x92 */
+	u16		reserved29;
+	u16		tfwptr;		/* PSC + 0x96 */
+	u16		reserved30;
+	u16		tflrfptr;	/* PSC + 0x9a */
+	u16		reserved31;
+	u16		tflwfptr;	/* PSC + 0x9e */
+};
+
+
+#endif  /* __ASM_MPC52xx_PSC_H__ */
diff --git a/include/asm-powerpc/mpc85xx.h b/include/asm-powerpc/mpc85xx.h
deleted file mode 100644
index 54142997a584..000000000000
--- a/include/asm-powerpc/mpc85xx.h
+++ /dev/null
@@ -1,45 +0,0 @@
-/*
- * include/asm-powerpc/mpc85xx.h
- *
- * MPC85xx definitions
- *
- * Maintainer: Kumar Gala <galak@kernel.crashing.org>
- *
- * Copyright 2004 Freescale Semiconductor, Inc
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- */
-
-#ifdef __KERNEL__
-#ifndef __ASM_MPC85xx_H__
-#define __ASM_MPC85xx_H__
-
-#include <asm/mmu.h>
-
-#ifdef CONFIG_85xx
-
-#if defined(CONFIG_MPC8540_ADS) || defined(CONFIG_MPC8560_ADS)
-#include <platforms/85xx/mpc85xx_ads.h>
-#endif
-#if defined(CONFIG_MPC8555_CDS) || defined(CONFIG_MPC8548_CDS)
-#include <platforms/85xx/mpc8555_cds.h>
-#endif
-#ifdef CONFIG_MPC85xx_CDS
-#include <platforms/85xx/mpc85xx_cds.h>
-#endif
-
-/* Let modules/drivers get at CCSRBAR */
-extern phys_addr_t get_ccsrbar(void);
-
-#ifdef MODULE
-#define CCSRBAR get_ccsrbar()
-#else
-#define CCSRBAR BOARD_CCSRBAR
-#endif
-
-#endif /* CONFIG_85xx */
-#endif /* __ASM_MPC85xx_H__ */
-#endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/mpic.h b/include/asm-powerpc/mpic.h
index 262db6b8da73..ae84dde3bc7f 100644
--- a/include/asm-powerpc/mpic.h
+++ b/include/asm-powerpc/mpic.h
@@ -224,8 +224,6 @@ struct mpic_reg_bank {
 	u32 __iomem	*base;
 #ifdef CONFIG_PPC_DCR
 	dcr_host_t	dhost;
-	unsigned int	dbase;
-	unsigned int	doff;
 #endif /* CONFIG_PPC_DCR */
 };
 
@@ -240,9 +238,6 @@ struct mpic_irq_save {
 /* The instance data of a given MPIC */
 struct mpic
 {
-	/* The device node of the interrupt controller */
-	struct device_node	*of_node;
-
 	/* The remapper for this MPIC */
 	struct irq_host		*irqhost;
 
@@ -292,10 +287,6 @@ struct mpic
 	struct mpic_reg_bank	cpuregs[MPIC_MAX_CPUS];
 	struct mpic_reg_bank	isus[MPIC_MAX_ISU];
 
-#ifdef CONFIG_PPC_DCR
-	unsigned int		dcr_base;
-#endif
-
 	/* Protected sources */
 	unsigned long		*protected;
 
@@ -309,6 +300,10 @@ struct mpic
 	unsigned long		*hwirq_bitmap;
 #endif
 
+#ifdef CONFIG_MPIC_BROKEN_REGREAD
+	u32			isu_reg0_shadow[MPIC_MAX_IRQ_SOURCES];
+#endif
+
 	/* link */
 	struct mpic		*next;
 
diff --git a/include/asm-powerpc/nvram.h b/include/asm-powerpc/nvram.h
index f3563e11e260..9877982508bf 100644
--- a/include/asm-powerpc/nvram.h
+++ b/include/asm-powerpc/nvram.h
@@ -63,8 +63,10 @@ struct nvram_partition {
 };
 
 
-extern int nvram_write_error_log(char * buff, int length, unsigned int err_type);
-extern int nvram_read_error_log(char * buff, int length, unsigned int * err_type);
+extern int nvram_write_error_log(char * buff, int length,
+					 unsigned int err_type, unsigned int err_seq);
+extern int nvram_read_error_log(char * buff, int length,
+					 unsigned int * err_type, unsigned int *err_seq);
 extern int nvram_clear_error_log(void);
 extern struct nvram_partition *nvram_find_partition(int sig, const char *name);
 
diff --git a/include/asm-powerpc/paca.h b/include/asm-powerpc/paca.h
index c6a5b1735666..fcd7b428ed0b 100644
--- a/include/asm-powerpc/paca.h
+++ b/include/asm-powerpc/paca.h
@@ -21,7 +21,18 @@
 #include	<asm/mmu.h>
 
 register struct paca_struct *local_paca asm("r13");
+
+#if defined(CONFIG_DEBUG_PREEMPT) && defined(CONFIG_SMP)
+extern unsigned int debug_smp_processor_id(void); /* from linux/smp.h */
+/*
+ * Add standard checks that preemption cannot occur when using get_paca():
+ * otherwise the paca_struct it points to may be the wrong one just after.
+ */
+#define get_paca()	((void) debug_smp_processor_id(), local_paca)
+#else
 #define get_paca()	local_paca
+#endif
+
 #define get_lppaca()	(get_paca()->lppaca_ptr)
 #define get_slb_shadow()	(get_paca()->slb_shadow_ptr)
 
diff --git a/include/asm-powerpc/page_64.h b/include/asm-powerpc/page_64.h
index 3448a3d4bc64..4ee82c61e4d7 100644
--- a/include/asm-powerpc/page_64.h
+++ b/include/asm-powerpc/page_64.h
@@ -26,12 +26,18 @@
  */
 #define PAGE_FACTOR		(PAGE_SHIFT - HW_PAGE_SHIFT)
 
-/* Segment size */
+/* Segment size; normal 256M segments */
 #define SID_SHIFT		28
-#define SID_MASK		0xfffffffffUL
+#define SID_MASK		ASM_CONST(0xfffffffff)
 #define ESID_MASK		0xfffffffff0000000UL
 #define GET_ESID(x)		(((x) >> SID_SHIFT) & SID_MASK)
 
+/* 1T segments */
+#define SID_SHIFT_1T		40
+#define SID_MASK_1T		0xffffffUL
+#define ESID_MASK_1T		0xffffff0000000000UL
+#define GET_ESID_1T(x)		(((x) >> SID_SHIFT_1T) & SID_MASK_1T)
+
 #ifndef __ASSEMBLY__
 #include <asm/cache.h>
 
@@ -121,6 +127,7 @@ extern unsigned int get_slice_psize(struct mm_struct *mm,
 
 extern void slice_init_context(struct mm_struct *mm, unsigned int psize);
 extern void slice_set_user_psize(struct mm_struct *mm, unsigned int psize);
+#define slice_mm_new_context(mm)	((mm)->context.id == 0)
 
 #define ARCH_HAS_HUGEPAGE_ONLY_RANGE
 extern int is_hugepage_only_range(struct mm_struct *m,
@@ -130,6 +137,12 @@ extern int is_hugepage_only_range(struct mm_struct *m,
 #endif /* __ASSEMBLY__ */
 #else
 #define slice_init()
+#define slice_set_user_psize(mm, psize)		\
+do {						\
+	(mm)->context.user_psize = (psize);	\
+	(mm)->context.sllp = SLB_VSID_USER | mmu_psize_defs[(psize)].sllp; \
+} while (0)
+#define slice_mm_new_context(mm)	1
 #endif /* CONFIG_PPC_MM_SLICES */
 
 #ifdef CONFIG_HUGETLB_PAGE
diff --git a/include/asm-powerpc/pci-bridge.h b/include/asm-powerpc/pci-bridge.h
index e909769b6410..dc318458b5fe 100644
--- a/include/asm-powerpc/pci-bridge.h
+++ b/include/asm-powerpc/pci-bridge.h
@@ -98,7 +98,8 @@ extern int early_find_capability(struct pci_controller *hose, int bus,
 				 int dev_fn, int cap);
 
 extern void setup_indirect_pci(struct pci_controller* hose,
-			       u32 cfg_addr, u32 cfg_data, u32 flags);
+			       resource_size_t cfg_addr,
+			       resource_size_t cfg_data, u32 flags);
 extern void setup_grackle(struct pci_controller *hose);
 extern void __init update_bridge_resource(struct pci_dev *dev,
 					  struct resource *res);
diff --git a/include/asm-powerpc/percpu.h b/include/asm-powerpc/percpu.h
index 73dc8ba4010d..6b229626d3ff 100644
--- a/include/asm-powerpc/percpu.h
+++ b/include/asm-powerpc/percpu.h
@@ -28,7 +28,7 @@
 /* var is in discarded region: offset to particular copy we want */
 #define per_cpu(var, cpu) (*RELOC_HIDE(&per_cpu__##var, __per_cpu_offset(cpu)))
 #define __get_cpu_var(var) (*RELOC_HIDE(&per_cpu__##var, __my_cpu_offset()))
-#define __raw_get_cpu_var(var) (*RELOC_HIDE(&per_cpu__##var, __my_cpu_offset()))
+#define __raw_get_cpu_var(var) (*RELOC_HIDE(&per_cpu__##var, local_paca->data_offset))
 
 /* A macro to avoid #include hell... */
 #define percpu_modcopy(pcpudst, src, size)			\
diff --git a/include/asm-powerpc/pgtable-4k.h b/include/asm-powerpc/pgtable-4k.h
index add5481fd7c7..818e2abc81e2 100644
--- a/include/asm-powerpc/pgtable-4k.h
+++ b/include/asm-powerpc/pgtable-4k.h
@@ -10,10 +10,12 @@
 #define PUD_INDEX_SIZE  7
 #define PGD_INDEX_SIZE  9
 
+#ifndef __ASSEMBLY__
 #define PTE_TABLE_SIZE	(sizeof(pte_t) << PTE_INDEX_SIZE)
 #define PMD_TABLE_SIZE	(sizeof(pmd_t) << PMD_INDEX_SIZE)
 #define PUD_TABLE_SIZE	(sizeof(pud_t) << PUD_INDEX_SIZE)
 #define PGD_TABLE_SIZE	(sizeof(pgd_t) << PGD_INDEX_SIZE)
+#endif	/* __ASSEMBLY__ */
 
 #define PTRS_PER_PTE	(1 << PTE_INDEX_SIZE)
 #define PTRS_PER_PMD	(1 << PMD_INDEX_SIZE)
diff --git a/include/asm-powerpc/pgtable-64k.h b/include/asm-powerpc/pgtable-64k.h
index 33ae9018fe72..bd54b772fbc6 100644
--- a/include/asm-powerpc/pgtable-64k.h
+++ b/include/asm-powerpc/pgtable-64k.h
@@ -9,9 +9,11 @@
 #define PUD_INDEX_SIZE	0
 #define PGD_INDEX_SIZE  4
 
+#ifndef __ASSEMBLY__
 #define PTE_TABLE_SIZE	(sizeof(real_pte_t) << PTE_INDEX_SIZE)
 #define PMD_TABLE_SIZE	(sizeof(pmd_t) << PMD_INDEX_SIZE)
 #define PGD_TABLE_SIZE	(sizeof(pgd_t) << PGD_INDEX_SIZE)
+#endif	/* __ASSEMBLY__ */
 
 #define PTRS_PER_PTE	(1 << PTE_INDEX_SIZE)
 #define PTRS_PER_PMD	(1 << PMD_INDEX_SIZE)
diff --git a/include/asm-powerpc/ppc_asm.h b/include/asm-powerpc/ppc_asm.h
index 65325721446d..2dbd4e7884fa 100644
--- a/include/asm-powerpc/ppc_asm.h
+++ b/include/asm-powerpc/ppc_asm.h
@@ -155,6 +155,20 @@ name: \
 	.type GLUE(.,name),@function; \
 GLUE(.,name):
 
+#define _INIT_GLOBAL(name) \
+	.section ".text.init.refok"; \
+	.align 2 ; \
+	.globl name; \
+	.globl GLUE(.,name); \
+	.section ".opd","aw"; \
+name: \
+	.quad GLUE(.,name); \
+	.quad .TOC.@tocbase; \
+	.quad 0; \
+	.previous; \
+	.type GLUE(.,name),@function; \
+GLUE(.,name):
+
 #define _KPROBE(name) \
 	.section ".kprobes.text","a"; \
 	.align 2 ; \
@@ -195,6 +209,10 @@ GLUE(.,name):
 
 #else /* 32-bit */
 
+#define _ENTRY(n)	\
+	.globl n;	\
+n:
+
 #define _GLOBAL(n)	\
 	.text;		\
 	.stabs __stringify(n:F-1),N_FUN,0,0,n;\
diff --git a/include/asm-powerpc/processor.h b/include/asm-powerpc/processor.h
index e28b10805159..dba7c948189d 100644
--- a/include/asm-powerpc/processor.h
+++ b/include/asm-powerpc/processor.h
@@ -145,9 +145,9 @@ struct thread_struct {
 	unsigned long	dabr;		/* Data address breakpoint register */
 #ifdef CONFIG_ALTIVEC
 	/* Complete AltiVec register set */
-	vector128	vr[32] __attribute((aligned(16)));
+	vector128	vr[32] __attribute__((aligned(16)));
 	/* AltiVec status */
-	vector128	vscr __attribute((aligned(16)));
+	vector128	vscr __attribute__((aligned(16)));
 	unsigned long	vrsave;
 	int		used_vr;	/* set if process has used altivec */
 #endif /* CONFIG_ALTIVEC */
diff --git a/include/asm-powerpc/prom.h b/include/asm-powerpc/prom.h
index 672083787a1d..925e2d384bb3 100644
--- a/include/asm-powerpc/prom.h
+++ b/include/asm-powerpc/prom.h
@@ -24,7 +24,7 @@
 #define OF_ROOT_NODE_ADDR_CELLS_DEFAULT	1
 #define OF_ROOT_NODE_SIZE_CELLS_DEFAULT	1
 
-#define of_compat_cmp(s1, s2, l)	strncasecmp((s1), (s2), (l))
+#define of_compat_cmp(s1, s2, l)	strcasecmp((s1), (s2))
 #define of_prop_cmp(s1, s2)		strcmp((s1), (s2))
 #define of_node_cmp(s1, s2)		strcasecmp((s1), (s2))
 
@@ -145,7 +145,6 @@ extern void of_detach_node(struct device_node *);
 extern void finish_device_tree(void);
 extern void unflatten_device_tree(void);
 extern void early_init_devtree(void *);
-#define device_is_compatible(d, c)	of_device_is_compatible((d), (c))
 extern int machine_is_compatible(const char *compat);
 extern void print_properties(struct device_node *node);
 extern int prom_n_intr_cells(struct device_node* np);
diff --git a/include/asm-powerpc/ps3.h b/include/asm-powerpc/ps3.h
index a6f3f5ee7ca7..f577a16c6728 100644
--- a/include/asm-powerpc/ps3.h
+++ b/include/asm-powerpc/ps3.h
@@ -229,6 +229,9 @@ enum lv1_result {
 	LV1_INVALID_CLASS_ID            = -21,
 	LV1_CONSTRAINT_NOT_SATISFIED    = -22,
 	LV1_ALIGNMENT_ERROR             = -23,
+	LV1_HARDWARE_ERROR              = -24,
+	LV1_INVALID_DATA_FORMAT         = -25,
+	LV1_INVALID_OPERATION           = -26,
 	LV1_INTERNAL_ERROR              = -32768,
 };
 
@@ -284,6 +287,12 @@ static inline const char* ps3_result(int result)
 		return "LV1_CONSTRAINT_NOT_SATISFIED (-22)";
 	case LV1_ALIGNMENT_ERROR:
 		return "LV1_ALIGNMENT_ERROR (-23)";
+	case LV1_HARDWARE_ERROR:
+		return "LV1_HARDWARE_ERROR (-24)";
+	case LV1_INVALID_DATA_FORMAT:
+		return "LV1_INVALID_DATA_FORMAT (-25)";
+	case LV1_INVALID_OPERATION:
+		return "LV1_INVALID_OPERATION (-26)";
 	case LV1_INTERNAL_ERROR:
 		return "LV1_INTERNAL_ERROR (-32768)";
 	default:
diff --git a/include/asm-powerpc/qe.h b/include/asm-powerpc/qe.h
index 9d304b1f1608..0dabe46a29d2 100644
--- a/include/asm-powerpc/qe.h
+++ b/include/asm-powerpc/qe.h
@@ -32,10 +32,13 @@
 extern void qe_reset(void);
 extern int par_io_init(struct device_node *np);
 extern int par_io_of_config(struct device_node *np);
+extern int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
+			     int assignment, int has_irq);
+extern int par_io_data_set(u8 port, u8 pin, u8 val);
 
 /* QE internal API */
 int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input);
-void qe_setbrg(u32 brg, u32 rate);
+void qe_setbrg(unsigned int brg, unsigned int rate, unsigned int multiplier);
 int qe_get_snum(void);
 void qe_put_snum(u8 snum);
 unsigned long qe_muram_alloc(int size, int align);
@@ -46,14 +49,28 @@ void *qe_muram_addr(unsigned long offset);
 
 /* Buffer descriptors */
 struct qe_bd {
-	u16 status;
-	u16 length;
-	u32 buf;
+	__be16 status;
+	__be16 length;
+	__be32 buf;
 } __attribute__ ((packed));
 
 #define BD_STATUS_MASK	0xffff0000
 #define BD_LENGTH_MASK	0x0000ffff
 
+#define BD_SC_EMPTY	0x8000	/* Receive is empty */
+#define BD_SC_READY	0x8000	/* Transmit is ready */
+#define BD_SC_WRAP	0x2000	/* Last buffer descriptor */
+#define BD_SC_INTRPT	0x1000	/* Interrupt on change */
+#define BD_SC_LAST	0x0800	/* Last buffer in frame */
+#define BD_SC_CM	0x0200	/* Continous mode */
+#define BD_SC_ID	0x0100	/* Rec'd too many idles */
+#define BD_SC_P		0x0100	/* xmt preamble */
+#define BD_SC_BR	0x0020	/* Break received */
+#define BD_SC_FR	0x0010	/* Framing error */
+#define BD_SC_PR	0x0008	/* Parity error */
+#define BD_SC_OV	0x0002	/* Overrun */
+#define BD_SC_CD	0x0001	/* ?? */
+
 /* Alignment */
 #define QE_INTR_TABLE_ALIGN	16	/* ??? */
 #define QE_ALIGNMENT_OF_BD	8
@@ -266,15 +283,12 @@ enum qe_clock {
 /* QE CECR Protocol - For non-MCC, specifies mode for QE CECR command */
 #define QE_CR_PROTOCOL_UNSPECIFIED	0x00	/* For all other protocols */
 #define QE_CR_PROTOCOL_HDLC_TRANSPARENT	0x00
+#define QE_CR_PROTOCOL_QMC		0x02
+#define QE_CR_PROTOCOL_UART		0x04
 #define QE_CR_PROTOCOL_ATM_POS		0x0A
 #define QE_CR_PROTOCOL_ETHERNET		0x0C
 #define QE_CR_PROTOCOL_L2_SWITCH	0x0D
 
-/* BMR byte order */
-#define QE_BMR_BYTE_ORDER_BO_PPC	0x08	/* powerpc little endian */
-#define QE_BMR_BYTE_ORDER_BO_MOT	0x10	/* motorola big endian */
-#define QE_BMR_BYTE_ORDER_BO_MAX	0x18
-
 /* BRG configuration register */
 #define QE_BRGC_ENABLE		0x00010000
 #define QE_BRGC_DIVISOR_SHIFT	1
@@ -321,41 +335,41 @@ enum qe_clock {
 #define UPGCR_ADDR	0x10000000	/* Master MPHY Addr multiplexing */
 #define UPGCR_DIAG	0x01000000	/* Diagnostic mode */
 
-/* UCC */
+/* UCC GUEMR register */
 #define UCC_GUEMR_MODE_MASK_RX	0x02
-#define UCC_GUEMR_MODE_MASK_TX	0x01
 #define UCC_GUEMR_MODE_FAST_RX	0x02
-#define UCC_GUEMR_MODE_FAST_TX	0x01
 #define UCC_GUEMR_MODE_SLOW_RX	0x00
+#define UCC_GUEMR_MODE_MASK_TX	0x01
+#define UCC_GUEMR_MODE_FAST_TX	0x01
 #define UCC_GUEMR_MODE_SLOW_TX	0x00
+#define UCC_GUEMR_MODE_MASK (UCC_GUEMR_MODE_MASK_RX | UCC_GUEMR_MODE_MASK_TX)
 #define UCC_GUEMR_SET_RESERVED3	0x10	/* Bit 3 in the guemr is reserved but
 					   must be set 1 */
 
 /* structure representing UCC SLOW parameter RAM */
 struct ucc_slow_pram {
-	u16 rbase;		/* RX BD base address */
-	u16 tbase;		/* TX BD base address */
-	u8 rfcr;		/* Rx function code */
-	u8 tfcr;		/* Tx function code */
-	u16 mrblr;		/* Rx buffer length */
-	u32 rstate;		/* Rx internal state */
-	u32 rptr;		/* Rx internal data pointer */
-	u16 rbptr;		/* rb BD Pointer */
-	u16 rcount;		/* Rx internal byte count */
-	u32 rtemp;		/* Rx temp */
-	u32 tstate;		/* Tx internal state */
-	u32 tptr;		/* Tx internal data pointer */
-	u16 tbptr;		/* Tx BD pointer */
-	u16 tcount;		/* Tx byte count */
-	u32 ttemp;		/* Tx temp */
-	u32 rcrc;		/* temp receive CRC */
-	u32 tcrc;		/* temp transmit CRC */
+	__be16 rbase;		/* RX BD base address */
+	__be16 tbase;		/* TX BD base address */
+	u8 rbmr;		/* RX bus mode register (same as CPM's RFCR) */
+	u8 tbmr;		/* TX bus mode register (same as CPM's TFCR) */
+	__be16 mrblr;		/* Rx buffer length */
+	__be32 rstate;		/* Rx internal state */
+	__be32 rptr;		/* Rx internal data pointer */
+	__be16 rbptr;		/* rb BD Pointer */
+	__be16 rcount;		/* Rx internal byte count */
+	__be32 rtemp;		/* Rx temp */
+	__be32 tstate;		/* Tx internal state */
+	__be32 tptr;		/* Tx internal data pointer */
+	__be16 tbptr;		/* Tx BD pointer */
+	__be16 tcount;		/* Tx byte count */
+	__be32 ttemp;		/* Tx temp */
+	__be32 rcrc;		/* temp receive CRC */
+	__be32 tcrc;		/* temp transmit CRC */
 } __attribute__ ((packed));
 
 /* General UCC SLOW Mode Register (GUMRH & GUMRL) */
-#define UCC_SLOW_GUMR_H_CRC16		0x00004000
-#define UCC_SLOW_GUMR_H_CRC16CCITT	0x00000000
-#define UCC_SLOW_GUMR_H_CRC32CCITT	0x00008000
+#define UCC_SLOW_GUMR_H_SAM_QMC		0x00000000
+#define UCC_SLOW_GUMR_H_SAM_SATM	0x00008000
 #define UCC_SLOW_GUMR_H_REVD		0x00002000
 #define UCC_SLOW_GUMR_H_TRX		0x00001000
 #define UCC_SLOW_GUMR_H_TTX		0x00000800
@@ -375,9 +389,33 @@ struct ucc_slow_pram {
 #define UCC_SLOW_GUMR_L_TCI		0x10000000
 #define UCC_SLOW_GUMR_L_RINV		0x02000000
 #define UCC_SLOW_GUMR_L_TINV		0x01000000
-#define UCC_SLOW_GUMR_L_TEND		0x00020000
+#define UCC_SLOW_GUMR_L_TEND		0x00040000
+#define UCC_SLOW_GUMR_L_TDCR_MASK	0x00030000
+#define UCC_SLOW_GUMR_L_TDCR_32	        0x00030000
+#define UCC_SLOW_GUMR_L_TDCR_16	        0x00020000
+#define UCC_SLOW_GUMR_L_TDCR_8	        0x00010000
+#define UCC_SLOW_GUMR_L_TDCR_1	        0x00000000
+#define UCC_SLOW_GUMR_L_RDCR_MASK	0x0000c000
+#define UCC_SLOW_GUMR_L_RDCR_32		0x0000c000
+#define UCC_SLOW_GUMR_L_RDCR_16	        0x00008000
+#define UCC_SLOW_GUMR_L_RDCR_8	        0x00004000
+#define UCC_SLOW_GUMR_L_RDCR_1		0x00000000
+#define UCC_SLOW_GUMR_L_RENC_NRZI	0x00000800
+#define UCC_SLOW_GUMR_L_RENC_NRZ	0x00000000
+#define UCC_SLOW_GUMR_L_TENC_NRZI	0x00000100
+#define UCC_SLOW_GUMR_L_TENC_NRZ	0x00000000
+#define UCC_SLOW_GUMR_L_DIAG_MASK	0x000000c0
+#define UCC_SLOW_GUMR_L_DIAG_LE	        0x000000c0
+#define UCC_SLOW_GUMR_L_DIAG_ECHO	0x00000080
+#define UCC_SLOW_GUMR_L_DIAG_LOOP	0x00000040
+#define UCC_SLOW_GUMR_L_DIAG_NORM	0x00000000
 #define UCC_SLOW_GUMR_L_ENR		0x00000020
 #define UCC_SLOW_GUMR_L_ENT		0x00000010
+#define UCC_SLOW_GUMR_L_MODE_MASK	0x0000000F
+#define UCC_SLOW_GUMR_L_MODE_BISYNC	0x00000008
+#define UCC_SLOW_GUMR_L_MODE_AHDLC	0x00000006
+#define UCC_SLOW_GUMR_L_MODE_UART	0x00000004
+#define UCC_SLOW_GUMR_L_MODE_QMC	0x00000002
 
 /* General UCC FAST Mode Register */
 #define UCC_FAST_GUMR_TCI	0x20000000
@@ -394,53 +432,111 @@ struct ucc_slow_pram {
 #define UCC_FAST_GUMR_ENR	0x00000020
 #define UCC_FAST_GUMR_ENT	0x00000010
 
-/* Slow UCC Event Register (UCCE) */
-#define UCC_SLOW_UCCE_GLR	0x1000
-#define UCC_SLOW_UCCE_GLT	0x0800
-#define UCC_SLOW_UCCE_DCC	0x0400
-#define UCC_SLOW_UCCE_FLG	0x0200
-#define UCC_SLOW_UCCE_AB	0x0200
-#define UCC_SLOW_UCCE_IDLE	0x0100
-#define UCC_SLOW_UCCE_GRA	0x0080
-#define UCC_SLOW_UCCE_TXE	0x0010
-#define UCC_SLOW_UCCE_RXF	0x0008
-#define UCC_SLOW_UCCE_CCR	0x0008
-#define UCC_SLOW_UCCE_RCH	0x0008
-#define UCC_SLOW_UCCE_BSY	0x0004
-#define UCC_SLOW_UCCE_TXB	0x0002
-#define UCC_SLOW_UCCE_TX	0x0002
-#define UCC_SLOW_UCCE_RX	0x0001
-#define UCC_SLOW_UCCE_GOV	0x0001
-#define UCC_SLOW_UCCE_GUN	0x0002
-#define UCC_SLOW_UCCE_GINT	0x0004
-#define UCC_SLOW_UCCE_IQOV	0x0008
-
-#define UCC_SLOW_UCCE_HDLC_SET	(UCC_SLOW_UCCE_TXE | UCC_SLOW_UCCE_BSY | \
-		UCC_SLOW_UCCE_GRA | UCC_SLOW_UCCE_TXB | UCC_SLOW_UCCE_RXF | \
-		UCC_SLOW_UCCE_DCC | UCC_SLOW_UCCE_GLT | UCC_SLOW_UCCE_GLR)
-#define UCC_SLOW_UCCE_ENET_SET	(UCC_SLOW_UCCE_TXE | UCC_SLOW_UCCE_BSY | \
-		UCC_SLOW_UCCE_GRA | UCC_SLOW_UCCE_TXB | UCC_SLOW_UCCE_RXF)
-#define UCC_SLOW_UCCE_TRANS_SET	(UCC_SLOW_UCCE_TXE | UCC_SLOW_UCCE_BSY | \
-		UCC_SLOW_UCCE_GRA | UCC_SLOW_UCCE_TX | UCC_SLOW_UCCE_RX | \
-		UCC_SLOW_UCCE_DCC | UCC_SLOW_UCCE_GLT | UCC_SLOW_UCCE_GLR)
-#define UCC_SLOW_UCCE_UART_SET	(UCC_SLOW_UCCE_BSY | UCC_SLOW_UCCE_GRA | \
-		UCC_SLOW_UCCE_TXB | UCC_SLOW_UCCE_TX | UCC_SLOW_UCCE_RX | \
-		UCC_SLOW_UCCE_GLT | UCC_SLOW_UCCE_GLR)
-#define UCC_SLOW_UCCE_QMC_SET	(UCC_SLOW_UCCE_IQOV | UCC_SLOW_UCCE_GINT | \
-		UCC_SLOW_UCCE_GUN | UCC_SLOW_UCCE_GOV)
-
-#define UCC_SLOW_UCCE_OTHER	(UCC_SLOW_UCCE_TXE | UCC_SLOW_UCCE_BSY | \
-		UCC_SLOW_UCCE_GRA | UCC_SLOW_UCCE_DCC | UCC_SLOW_UCCE_GLT | \
-		UCC_SLOW_UCCE_GLR)
-
-#define UCC_SLOW_INTR_TX	UCC_SLOW_UCCE_TXB
-#define UCC_SLOW_INTR_RX	(UCC_SLOW_UCCE_RXF | UCC_SLOW_UCCE_RX)
-#define UCC_SLOW_INTR		(UCC_SLOW_INTR_TX | UCC_SLOW_INTR_RX)
+/* UART Slow UCC Event Register (UCCE) */
+#define UCC_UART_UCCE_AB	0x0200
+#define UCC_UART_UCCE_IDLE	0x0100
+#define UCC_UART_UCCE_GRA	0x0080
+#define UCC_UART_UCCE_BRKE	0x0040
+#define UCC_UART_UCCE_BRKS	0x0020
+#define UCC_UART_UCCE_CCR	0x0008
+#define UCC_UART_UCCE_BSY	0x0004
+#define UCC_UART_UCCE_TX	0x0002
+#define UCC_UART_UCCE_RX	0x0001
+
+/* HDLC Slow UCC Event Register (UCCE) */
+#define UCC_HDLC_UCCE_GLR	0x1000
+#define UCC_HDLC_UCCE_GLT	0x0800
+#define UCC_HDLC_UCCE_IDLE	0x0100
+#define UCC_HDLC_UCCE_BRKE	0x0040
+#define UCC_HDLC_UCCE_BRKS	0x0020
+#define UCC_HDLC_UCCE_TXE	0x0010
+#define UCC_HDLC_UCCE_RXF	0x0008
+#define UCC_HDLC_UCCE_BSY	0x0004
+#define UCC_HDLC_UCCE_TXB	0x0002
+#define UCC_HDLC_UCCE_RXB	0x0001
+
+/* BISYNC Slow UCC Event Register (UCCE) */
+#define UCC_BISYNC_UCCE_GRA	0x0080
+#define UCC_BISYNC_UCCE_TXE	0x0010
+#define UCC_BISYNC_UCCE_RCH	0x0008
+#define UCC_BISYNC_UCCE_BSY	0x0004
+#define UCC_BISYNC_UCCE_TXB	0x0002
+#define UCC_BISYNC_UCCE_RXB	0x0001
+
+/* Gigabit Ethernet Fast UCC Event Register (UCCE) */
+#define UCC_GETH_UCCE_MPD       0x80000000
+#define UCC_GETH_UCCE_SCAR      0x40000000
+#define UCC_GETH_UCCE_GRA       0x20000000
+#define UCC_GETH_UCCE_CBPR      0x10000000
+#define UCC_GETH_UCCE_BSY       0x08000000
+#define UCC_GETH_UCCE_RXC       0x04000000
+#define UCC_GETH_UCCE_TXC       0x02000000
+#define UCC_GETH_UCCE_TXE       0x01000000
+#define UCC_GETH_UCCE_TXB7      0x00800000
+#define UCC_GETH_UCCE_TXB6      0x00400000
+#define UCC_GETH_UCCE_TXB5      0x00200000
+#define UCC_GETH_UCCE_TXB4      0x00100000
+#define UCC_GETH_UCCE_TXB3      0x00080000
+#define UCC_GETH_UCCE_TXB2      0x00040000
+#define UCC_GETH_UCCE_TXB1      0x00020000
+#define UCC_GETH_UCCE_TXB0      0x00010000
+#define UCC_GETH_UCCE_RXB7      0x00008000
+#define UCC_GETH_UCCE_RXB6      0x00004000
+#define UCC_GETH_UCCE_RXB5      0x00002000
+#define UCC_GETH_UCCE_RXB4      0x00001000
+#define UCC_GETH_UCCE_RXB3      0x00000800
+#define UCC_GETH_UCCE_RXB2      0x00000400
+#define UCC_GETH_UCCE_RXB1      0x00000200
+#define UCC_GETH_UCCE_RXB0      0x00000100
+#define UCC_GETH_UCCE_RXF7      0x00000080
+#define UCC_GETH_UCCE_RXF6      0x00000040
+#define UCC_GETH_UCCE_RXF5      0x00000020
+#define UCC_GETH_UCCE_RXF4      0x00000010
+#define UCC_GETH_UCCE_RXF3      0x00000008
+#define UCC_GETH_UCCE_RXF2      0x00000004
+#define UCC_GETH_UCCE_RXF1      0x00000002
+#define UCC_GETH_UCCE_RXF0      0x00000001
+
+/* UPSMR, when used as a UART */
+#define UCC_UART_UPSMR_FLC		0x8000
+#define UCC_UART_UPSMR_SL		0x4000
+#define UCC_UART_UPSMR_CL_MASK		0x3000
+#define UCC_UART_UPSMR_CL_8		0x3000
+#define UCC_UART_UPSMR_CL_7		0x2000
+#define UCC_UART_UPSMR_CL_6		0x1000
+#define UCC_UART_UPSMR_CL_5		0x0000
+#define UCC_UART_UPSMR_UM_MASK		0x0c00
+#define UCC_UART_UPSMR_UM_NORMAL	0x0000
+#define UCC_UART_UPSMR_UM_MAN_MULTI	0x0400
+#define UCC_UART_UPSMR_UM_AUTO_MULTI	0x0c00
+#define UCC_UART_UPSMR_FRZ		0x0200
+#define UCC_UART_UPSMR_RZS		0x0100
+#define UCC_UART_UPSMR_SYN		0x0080
+#define UCC_UART_UPSMR_DRT		0x0040
+#define UCC_UART_UPSMR_PEN		0x0010
+#define UCC_UART_UPSMR_RPM_MASK		0x000c
+#define UCC_UART_UPSMR_RPM_ODD		0x0000
+#define UCC_UART_UPSMR_RPM_LOW		0x0004
+#define UCC_UART_UPSMR_RPM_EVEN		0x0008
+#define UCC_UART_UPSMR_RPM_HIGH		0x000C
+#define UCC_UART_UPSMR_TPM_MASK		0x0003
+#define UCC_UART_UPSMR_TPM_ODD		0x0000
+#define UCC_UART_UPSMR_TPM_LOW		0x0001
+#define UCC_UART_UPSMR_TPM_EVEN		0x0002
+#define UCC_UART_UPSMR_TPM_HIGH		0x0003
 
 /* UCC Transmit On Demand Register (UTODR) */
 #define UCC_SLOW_TOD	0x8000
 #define UCC_FAST_TOD	0x8000
 
+/* UCC Bus Mode Register masks */
+/* Not to be confused with the Bundle Mode Register */
+#define UCC_BMR_GBL		0x20
+#define UCC_BMR_BO_BE		0x10
+#define UCC_BMR_CETM		0x04
+#define UCC_BMR_DTB		0x02
+#define UCC_BMR_BDB		0x01
+
 /* Function code masks */
 #define FC_GBL				0x20
 #define FC_DTB_LCL			0x02
diff --git a/include/asm-powerpc/qe_ic.h b/include/asm-powerpc/qe_ic.h
index e386fb7e44b0..a779b2c9eaf1 100644
--- a/include/asm-powerpc/qe_ic.h
+++ b/include/asm-powerpc/qe_ic.h
@@ -56,9 +56,75 @@ enum qe_ic_grp_id {
 	QE_IC_GRP_RISCB		/* QE interrupt controller RISC group B */
 };
 
-void qe_ic_init(struct device_node *node, unsigned int flags);
+void qe_ic_init(struct device_node *node, unsigned int flags,
+		void (*low_handler)(unsigned int irq, struct irq_desc *desc),
+		void (*high_handler)(unsigned int irq, struct irq_desc *desc));
 void qe_ic_set_highest_priority(unsigned int virq, int high);
 int qe_ic_set_priority(unsigned int virq, unsigned int priority);
 int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high);
 
+struct qe_ic;
+unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic);
+unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic);
+
+static inline void qe_ic_cascade_low_ipic(unsigned int irq,
+					  struct irq_desc *desc)
+{
+	struct qe_ic *qe_ic = desc->handler_data;
+	unsigned int cascade_irq = qe_ic_get_low_irq(qe_ic);
+
+	if (cascade_irq != NO_IRQ)
+		generic_handle_irq(cascade_irq);
+}
+
+static inline void qe_ic_cascade_high_ipic(unsigned int irq,
+					   struct irq_desc *desc)
+{
+	struct qe_ic *qe_ic = desc->handler_data;
+	unsigned int cascade_irq = qe_ic_get_high_irq(qe_ic);
+
+	if (cascade_irq != NO_IRQ)
+		generic_handle_irq(cascade_irq);
+}
+
+static inline void qe_ic_cascade_low_mpic(unsigned int irq,
+					  struct irq_desc *desc)
+{
+	struct qe_ic *qe_ic = desc->handler_data;
+	unsigned int cascade_irq = qe_ic_get_low_irq(qe_ic);
+
+	if (cascade_irq != NO_IRQ)
+		generic_handle_irq(cascade_irq);
+
+	desc->chip->eoi(irq);
+}
+
+static inline void qe_ic_cascade_high_mpic(unsigned int irq,
+					   struct irq_desc *desc)
+{
+	struct qe_ic *qe_ic = desc->handler_data;
+	unsigned int cascade_irq = qe_ic_get_high_irq(qe_ic);
+
+	if (cascade_irq != NO_IRQ)
+		generic_handle_irq(cascade_irq);
+
+	desc->chip->eoi(irq);
+}
+
+static inline void qe_ic_cascade_muxed_mpic(unsigned int irq,
+					    struct irq_desc *desc)
+{
+	struct qe_ic *qe_ic = desc->handler_data;
+	unsigned int cascade_irq;
+
+	cascade_irq = qe_ic_get_high_irq(qe_ic);
+	if (cascade_irq == NO_IRQ)
+		cascade_irq = qe_ic_get_low_irq(qe_ic);
+
+	if (cascade_irq != NO_IRQ)
+		generic_handle_irq(cascade_irq);
+
+	desc->chip->eoi(irq);
+}
+
 #endif /* _ASM_POWERPC_QE_IC_H */
diff --git a/include/asm-powerpc/reg.h b/include/asm-powerpc/reg.h
index 281011e953ec..e775ff1ca413 100644
--- a/include/asm-powerpc/reg.h
+++ b/include/asm-powerpc/reg.h
@@ -102,12 +102,8 @@
 #else /* 32-bit */
 /* Default MSR for kernel mode. */
 #ifndef MSR_KERNEL	/* reg_booke.h also defines this */
-#ifdef CONFIG_APUS_FAST_EXCEPT
-#define MSR_KERNEL	(MSR_ME|MSR_IP|MSR_RI|MSR_IR|MSR_DR)
-#else
 #define MSR_KERNEL	(MSR_ME|MSR_RI|MSR_IR|MSR_DR)
 #endif
-#endif
 
 #define MSR_USER	(MSR_KERNEL|MSR_PR|MSR_EE)
 #endif
@@ -518,21 +514,47 @@
 #define   PA6T_MMCR1_ES4	0x0000000000ff0000UL
 #define   PA6T_MMCR1_ES5	0x00000000ff000000UL
 
-#define SPRN_PA6T_SIAR  780
-#define SPRN_PA6T_UPMC0 771
-#define SPRN_PA6T_UPMC1 772
+#define SPRN_PA6T_UPMC0 771	/* User PerfMon Counter 0 */
+#define SPRN_PA6T_UPMC1 772	/* ... */
 #define SPRN_PA6T_UPMC2 773
 #define SPRN_PA6T_UPMC3 774
 #define SPRN_PA6T_UPMC4 775
 #define SPRN_PA6T_UPMC5 776
-#define SPRN_PA6T_UMMCR0 779
-#define SPRN_PA6T_UMMCR1 782
-#define SPRN_PA6T_PMC0  787
-#define SPRN_PA6T_PMC1  788
-#define SPRN_PA6T_PMC2  789
-#define SPRN_PA6T_PMC3  790
-#define SPRN_PA6T_PMC4  791
-#define SPRN_PA6T_PMC5  792
+#define SPRN_PA6T_UMMCR0 779	/* User Monitor Mode Control Register 0 */
+#define SPRN_PA6T_SIAR	780	/* Sampled Instruction Address */
+#define SPRN_PA6T_UMMCR1 782	/* User Monitor Mode Control Register 1 */
+#define SPRN_PA6T_SIER	785	/* Sampled Instruction Event Register */
+#define SPRN_PA6T_PMC0	787
+#define SPRN_PA6T_PMC1	788
+#define SPRN_PA6T_PMC2	789
+#define SPRN_PA6T_PMC3	790
+#define SPRN_PA6T_PMC4	791
+#define SPRN_PA6T_PMC5	792
+#define SPRN_PA6T_TSR0	793	/* Timestamp Register 0 */
+#define SPRN_PA6T_TSR1	794	/* Timestamp Register 1 */
+#define SPRN_PA6T_TSR2	799	/* Timestamp Register 2 */
+#define SPRN_PA6T_TSR3	784	/* Timestamp Register 3 */
+
+#define SPRN_PA6T_IER	981	/* Icache Error Register */
+#define SPRN_PA6T_DER	982	/* Dcache Error Register */
+#define SPRN_PA6T_BER	862	/* BIU Error Address Register */
+#define SPRN_PA6T_MER	849	/* MMU Error Register */
+
+#define SPRN_PA6T_IMA0	880	/* Instruction Match Array 0 */
+#define SPRN_PA6T_IMA1	881	/* ... */
+#define SPRN_PA6T_IMA2	882
+#define SPRN_PA6T_IMA3	883
+#define SPRN_PA6T_IMA4	884
+#define SPRN_PA6T_IMA5	885
+#define SPRN_PA6T_IMA6	886
+#define SPRN_PA6T_IMA7	887
+#define SPRN_PA6T_IMA8	888
+#define SPRN_PA6T_IMA9	889
+#define SPRN_PA6T_BTCR	978	/* Breakpoint and Tagging Control Register */
+#define SPRN_PA6T_IMAAT	979	/* Instruction Match Array Action Table */
+#define SPRN_PA6T_PCCR	1019	/* Power Counter Control Register */
+#define SPRN_PA6T_RPCCR	1021	/* Retire PC Trace Control Register */
+
 
 #else /* 32-bit */
 #define SPRN_MMCR0	952	/* Monitor Mode Control Register 0 */
diff --git a/include/asm-powerpc/rwsem.h b/include/asm-powerpc/rwsem.h
index e929145e1e46..cefc14728cc5 100644
--- a/include/asm-powerpc/rwsem.h
+++ b/include/asm-powerpc/rwsem.h
@@ -1,6 +1,10 @@
 #ifndef _ASM_POWERPC_RWSEM_H
 #define _ASM_POWERPC_RWSEM_H
 
+#ifndef _LINUX_RWSEM_H
+#error "Please don't include <asm/rwsem.h> directly, use <linux/rwsem.h> instead."
+#endif
+
 #ifdef __KERNEL__
 
 /*
diff --git a/include/asm-powerpc/smp.h b/include/asm-powerpc/smp.h
index d037f50580e2..19102bfc14ca 100644
--- a/include/asm-powerpc/smp.h
+++ b/include/asm-powerpc/smp.h
@@ -45,7 +45,7 @@ void generic_mach_cpu_die(void);
 #endif
 
 #ifdef CONFIG_PPC64
-#define raw_smp_processor_id()	(get_paca()->paca_index)
+#define raw_smp_processor_id()	(local_paca->paca_index)
 #define hard_smp_processor_id() (get_paca()->hw_cpu_id)
 #else
 /* 32-bit */
diff --git a/include/asm-powerpc/spu.h b/include/asm-powerpc/spu.h
index 5bde3980bf49..b1accce77bb5 100644
--- a/include/asm-powerpc/spu.h
+++ b/include/asm-powerpc/spu.h
@@ -238,19 +238,14 @@ extern long spu_sys_callback(struct spu_syscall_block *s);
 
 /* syscalls implemented in spufs */
 struct file;
-extern struct spufs_calls {
-	asmlinkage long (*create_thread)(const char __user *name,
+struct spufs_calls {
+	long (*create_thread)(const char __user *name,
 					unsigned int flags, mode_t mode,
 					struct file *neighbor);
-	asmlinkage long (*spu_run)(struct file *filp, __u32 __user *unpc,
+	long (*spu_run)(struct file *filp, __u32 __user *unpc,
 						__u32 __user *ustatus);
-	struct module *owner;
-} spufs_calls;
-
-/* coredump calls implemented in spufs */
-struct spu_coredump_calls {
-	asmlinkage int (*arch_notes_size)(void);
-	asmlinkage void (*arch_write_notes)(struct file *file);
+	int (*coredump_extra_notes_size)(void);
+	int (*coredump_extra_notes_write)(struct file *file, loff_t *foffset);
 	struct module *owner;
 };
 
@@ -274,21 +269,8 @@ struct spu_coredump_calls {
 #define SPU_CREATE_FLAG_ALL		0x003f /* mask of all valid flags */
 
 
-#ifdef CONFIG_SPU_FS_MODULE
 int register_spu_syscalls(struct spufs_calls *calls);
 void unregister_spu_syscalls(struct spufs_calls *calls);
-#else
-static inline int register_spu_syscalls(struct spufs_calls *calls)
-{
-	return 0;
-}
-static inline void unregister_spu_syscalls(struct spufs_calls *calls)
-{
-}
-#endif /* MODULE */
-
-int register_arch_coredump_calls(struct spu_coredump_calls *calls);
-void unregister_arch_coredump_calls(struct spu_coredump_calls *calls);
 
 int spu_add_sysdev_attr(struct sysdev_attribute *attr);
 void spu_remove_sysdev_attr(struct sysdev_attribute *attr);
diff --git a/include/asm-powerpc/system.h b/include/asm-powerpc/system.h
index 41520b7a7b76..d10e99bf5001 100644
--- a/include/asm-powerpc/system.h
+++ b/include/asm-powerpc/system.h
@@ -189,6 +189,9 @@ extern int mem_init_done;	/* set on boot once kmalloc can be called */
 extern unsigned long memory_limit;
 extern unsigned long klimit;
 
+extern void *alloc_maybe_bootmem(size_t size, gfp_t mask);
+extern void *zalloc_maybe_bootmem(size_t size, gfp_t mask);
+
 extern int powersave_nap;	/* set if nap mode can be used in idle loop */
 
 /*
diff --git a/include/asm-powerpc/time.h b/include/asm-powerpc/time.h
index c104c15c6625..f05895522f7f 100644
--- a/include/asm-powerpc/time.h
+++ b/include/asm-powerpc/time.h
@@ -179,7 +179,7 @@ static inline unsigned int get_dec(void)
 static inline void set_dec(int val)
 {
 #if defined(CONFIG_40x)
-	return;		/* Have to let it auto-reload */
+	mtspr(SPRN_PIT, val);
 #elif defined(CONFIG_8xx_CPU6)
 	set_dec_cpu6(val);
 #else
@@ -245,6 +245,7 @@ extern void snapshot_timebases(void);
 #define snapshot_timebases()			do { } while (0)
 #endif
 
+extern void secondary_cpu_time_init(void);
 extern void iSeries_time_init_early(void);
 
 #endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/tlb.h b/include/asm-powerpc/tlb.h
index 66714042e438..e20ff7541f36 100644
--- a/include/asm-powerpc/tlb.h
+++ b/include/asm-powerpc/tlb.h
@@ -23,6 +23,8 @@
 #include <asm/mmu.h>
 #endif
 
+#include <linux/pagemap.h>
+
 struct mmu_gather;
 
 #define tlb_start_vma(tlb, vma)	do { } while (0)
diff --git a/include/asm-powerpc/tlbflush.h b/include/asm-powerpc/tlbflush.h
index 99a0439baa50..a022f806bb21 100644
--- a/include/asm-powerpc/tlbflush.h
+++ b/include/asm-powerpc/tlbflush.h
@@ -97,6 +97,7 @@ struct ppc64_tlb_batch {
 	real_pte_t		pte[PPC64_TLB_BATCH_NR];
 	unsigned long		vaddr[PPC64_TLB_BATCH_NR];
 	unsigned int		psize;
+	int			ssize;
 };
 DECLARE_PER_CPU(struct ppc64_tlb_batch, ppc64_tlb_batch);
 
@@ -127,7 +128,7 @@ static inline void arch_leave_lazy_mmu_mode(void)
 
 
 extern void flush_hash_page(unsigned long va, real_pte_t pte, int psize,
-			    int local);
+			    int ssize, int local);
 extern void flush_hash_range(unsigned long number, int local);
 
 
diff --git a/include/asm-powerpc/types.h b/include/asm-powerpc/types.h
index 3b363757a2bb..a584341c87e3 100644
--- a/include/asm-powerpc/types.h
+++ b/include/asm-powerpc/types.h
@@ -48,7 +48,7 @@ typedef unsigned long long __u64;
 
 typedef struct {
 	__u32 u[4];
-} __attribute((aligned(16))) __vector128;
+} __attribute__((aligned(16))) __vector128;
 
 #endif /* __ASSEMBLY__ */
 
diff --git a/include/asm-powerpc/ucc.h b/include/asm-powerpc/ucc.h
index afe3076bdc03..46b09ba6bead 100644
--- a/include/asm-powerpc/ucc.h
+++ b/include/asm-powerpc/ucc.h
@@ -25,58 +25,38 @@
 /* Slow or fast type for UCCs.
 */
 enum ucc_speed_type {
-	UCC_SPEED_TYPE_FAST, UCC_SPEED_TYPE_SLOW
-};
-
-/* Initial UCCs Parameter RAM address relative to: MEM_MAP_BASE (IMMR).
-*/
-enum ucc_pram_initial_offset {
-	UCC_PRAM_OFFSET_UCC1 = 0x8400,
-	UCC_PRAM_OFFSET_UCC2 = 0x8500,
-	UCC_PRAM_OFFSET_UCC3 = 0x8600,
-	UCC_PRAM_OFFSET_UCC4 = 0x9000,
-	UCC_PRAM_OFFSET_UCC5 = 0x8000,
-	UCC_PRAM_OFFSET_UCC6 = 0x8100,
-	UCC_PRAM_OFFSET_UCC7 = 0x8200,
-	UCC_PRAM_OFFSET_UCC8 = 0x8300
+	UCC_SPEED_TYPE_FAST = UCC_GUEMR_MODE_FAST_RX | UCC_GUEMR_MODE_FAST_TX,
+	UCC_SPEED_TYPE_SLOW = UCC_GUEMR_MODE_SLOW_RX | UCC_GUEMR_MODE_SLOW_TX
 };
 
 /* ucc_set_type
  * Sets UCC to slow or fast mode.
  *
  * ucc_num - (In) number of UCC (0-7).
- * regs    - (In) pointer to registers base for the UCC.
  * speed   - (In) slow or fast mode for UCC.
  */
-int ucc_set_type(int ucc_num, struct ucc_common *regs,
-		 enum ucc_speed_type speed);
-
-/* ucc_init_guemr
- * Init the Guemr register.
- *
- * regs - (In) pointer to registers base for the UCC.
- */
-int ucc_init_guemr(struct ucc_common *regs);
+int ucc_set_type(unsigned int ucc_num, enum ucc_speed_type speed);
 
-int ucc_set_qe_mux_mii_mng(int ucc_num);
+int ucc_set_qe_mux_mii_mng(unsigned int ucc_num);
 
-int ucc_set_qe_mux_rxtx(int ucc_num, enum qe_clock clock, enum comm_dir mode);
+int ucc_set_qe_mux_rxtx(unsigned int ucc_num, enum qe_clock clock,
+	enum comm_dir mode);
 
-int ucc_mux_set_grant_tsa_bkpt(int ucc_num, int set, u32 mask);
+int ucc_mux_set_grant_tsa_bkpt(unsigned int ucc_num, int set, u32 mask);
 
 /* QE MUX clock routing for UCC
 */
-static inline int ucc_set_qe_mux_grant(int ucc_num, int set)
+static inline int ucc_set_qe_mux_grant(unsigned int ucc_num, int set)
 {
 	return ucc_mux_set_grant_tsa_bkpt(ucc_num, set, QE_CMXUCR_GRANT);
 }
 
-static inline int ucc_set_qe_mux_tsa(int ucc_num, int set)
+static inline int ucc_set_qe_mux_tsa(unsigned int ucc_num, int set)
 {
 	return ucc_mux_set_grant_tsa_bkpt(ucc_num, set, QE_CMXUCR_TSA);
 }
 
-static inline int ucc_set_qe_mux_bkpt(int ucc_num, int set)
+static inline int ucc_set_qe_mux_bkpt(unsigned int ucc_num, int set)
 {
 	return ucc_mux_set_grant_tsa_bkpt(ucc_num, set, QE_CMXUCR_BKPT);
 }
diff --git a/include/asm-powerpc/ucc_slow.h b/include/asm-powerpc/ucc_slow.h
index fdaac9d762bb..0980e6ad335b 100644
--- a/include/asm-powerpc/ucc_slow.h
+++ b/include/asm-powerpc/ucc_slow.h
@@ -148,9 +148,10 @@ enum ucc_slow_diag_mode {
 
 struct ucc_slow_info {
 	int ucc_num;
+	int protocol;			/* QE_CR_PROTOCOL_xxx */
 	enum qe_clock rx_clock;
 	enum qe_clock tx_clock;
-	u32 regs;
+	phys_addr_t regs;
 	int irq;
 	u16 uccm_mask;
 	int data_mem_part;
@@ -186,7 +187,7 @@ struct ucc_slow_info {
 
 struct ucc_slow_private {
 	struct ucc_slow_info *us_info;
-	struct ucc_slow *us_regs;	/* a pointer to memory map of UCC regs */
+	struct ucc_slow __iomem *us_regs; /* Ptr to memory map of UCC regs */
 	struct ucc_slow_pram *us_pram;	/* a pointer to the parameter RAM */
 	u32 us_pram_offset;
 	int enabled_tx;		/* Whether channel is enabled for Tx (ENT) */
@@ -277,12 +278,12 @@ void ucc_slow_graceful_stop_tx(struct ucc_slow_private * uccs);
  */
 void ucc_slow_stop_tx(struct ucc_slow_private * uccs);
 
-/* ucc_slow_restart_x
+/* ucc_slow_restart_tx
  * Restarts transmitting on a specified slow UCC.
  *
  * uccs - (In) pointer to the slow UCC structure.
  */
-void ucc_slow_restart_x(struct ucc_slow_private * uccs);
+void ucc_slow_restart_tx(struct ucc_slow_private *uccs);
 
 u32 ucc_slow_get_qe_cr_subblock(int uccs_num);
 
diff --git a/include/asm-powerpc/udbg.h b/include/asm-powerpc/udbg.h
index ce9d82fb7b68..a9e0b0ebcb0f 100644
--- a/include/asm-powerpc/udbg.h
+++ b/include/asm-powerpc/udbg.h
@@ -48,6 +48,7 @@ extern void __init udbg_init_rtas_console(void);
 extern void __init udbg_init_debug_beat(void);
 extern void __init udbg_init_btext(void);
 extern void __init udbg_init_44x_as1(void);
+extern void __init udbg_init_cpm(void);
 
 #endif /* __KERNEL__ */
 #endif /* _ASM_POWERPC_UDBG_H */
diff --git a/include/asm-powerpc/vio.h b/include/asm-powerpc/vio.h
index 3a0975e2adad..9204c15839c5 100644
--- a/include/asm-powerpc/vio.h
+++ b/include/asm-powerpc/vio.h
@@ -53,18 +53,12 @@ struct vio_dev {
 };
 
 struct vio_driver {
-	struct list_head node;
 	const struct vio_device_id *id_table;
 	int (*probe)(struct vio_dev *dev, const struct vio_device_id *id);
 	int (*remove)(struct vio_dev *dev);
-	void (*shutdown)(struct vio_dev *dev);
-	unsigned long driver_data;
 	struct device_driver driver;
 };
 
-extern struct dma_mapping_ops vio_dma_ops;
-extern struct bus_type vio_bus_type;
-
 extern int vio_register_driver(struct vio_driver *drv);
 extern void vio_unregister_driver(struct vio_driver *drv);
 
diff --git a/include/asm-powerpc/xilinx_intc.h b/include/asm-powerpc/xilinx_intc.h
new file mode 100644
index 000000000000..343612f8fece
--- /dev/null
+++ b/include/asm-powerpc/xilinx_intc.h
@@ -0,0 +1,20 @@
+/*
+ * Xilinx intc external definitions
+ *
+ * Copyright 2007 Secret Lab Technologies Ltd.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+#ifndef _ASM_POWERPC_XILINX_INTC_H
+#define _ASM_POWERPC_XILINX_INTC_H
+
+#ifdef __KERNEL__
+
+extern void __init xilinx_intc_init_tree(void);
+extern unsigned int xilinx_intc_get_irq(void);
+
+#endif /* __KERNEL__ */
+#endif /* _ASM_POWERPC_XILINX_INTC_H */
diff --git a/include/asm-ppc/amigahw.h b/include/asm-ppc/amigahw.h
deleted file mode 100644
index 90fd1274d727..000000000000
--- a/include/asm-ppc/amigahw.h
+++ /dev/null
@@ -1,16 +0,0 @@
-#ifdef __KERNEL__
-#ifndef __ASMPPC_AMIGAHW_H
-#define __ASMPPC_AMIGAHW_H
-
-#include <asm-m68k/amigahw.h>
-
-#undef CHIP_PHYSADDR
-#ifdef CONFIG_APUS_FAST_EXCEPT
-#define CHIP_PHYSADDR      (0x000000)
-#else
-#define CHIP_PHYSADDR      (0x004000)
-#endif
-
-
-#endif /* __ASMPPC_AMIGAHW_H */
-#endif /* __KERNEL__ */
diff --git a/include/asm-ppc/amigaints.h b/include/asm-ppc/amigaints.h
deleted file mode 100644
index aa3ff6349e81..000000000000
--- a/include/asm-ppc/amigaints.h
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
-** amigaints.h -- Amiga Linux interrupt handling structs and prototypes
-**
-** Copyright 1992 by Greg Harp
-**
-** This file is subject to the terms and conditions of the GNU General Public
-** License.  See the file COPYING in the main directory of this archive
-** for more details.
-**
-** Created 10/2/92 by Greg Harp
-*/
-
-#ifdef __KERNEL__
-#ifndef _ASMm68k_AMIGAINTS_H_
-#define _ASMm68k_AMIGAINTS_H_
-
-/*
-** Amiga Interrupt sources.
-**
-*/
-
-#define AUTO_IRQS           (8)
-#define AMI_STD_IRQS        (14)
-#define CIA_IRQS            (5)
-#define AMI_IRQS            (32) /* AUTO_IRQS+AMI_STD_IRQS+2*CIA_IRQS */
-
-/* vertical blanking interrupt */
-#define IRQ_AMIGA_VERTB     0
-
-/* copper interrupt */
-#define IRQ_AMIGA_COPPER    1
-
-/* Audio interrupts */
-#define IRQ_AMIGA_AUD0	    2
-#define IRQ_AMIGA_AUD1	    3
-#define IRQ_AMIGA_AUD2	    4
-#define IRQ_AMIGA_AUD3	    5
-
-/* Blitter done interrupt */
-#define IRQ_AMIGA_BLIT	    6
-
-/* floppy disk interrupts */
-#define IRQ_AMIGA_DSKSYN    7
-#define IRQ_AMIGA_DSKBLK    8
-
-/* builtin serial port interrupts */
-#define IRQ_AMIGA_RBF	    9
-#define IRQ_AMIGA_TBE	    10
-
-/* software interrupts */
-#define IRQ_AMIGA_SOFT      11
-
-/* interrupts from external hardware */
-#define IRQ_AMIGA_PORTS	    12
-#define IRQ_AMIGA_EXTER	    13
-
-/* CIA interrupt sources */
-#define IRQ_AMIGA_CIAA      14
-#define IRQ_AMIGA_CIAA_TA   14
-#define IRQ_AMIGA_CIAA_TB   15
-#define IRQ_AMIGA_CIAA_ALRM 16
-#define IRQ_AMIGA_CIAA_SP   17
-#define IRQ_AMIGA_CIAA_FLG  18
-#define IRQ_AMIGA_CIAB      19
-#define IRQ_AMIGA_CIAB_TA   19
-#define IRQ_AMIGA_CIAB_TB   20
-#define IRQ_AMIGA_CIAB_ALRM 21
-#define IRQ_AMIGA_CIAB_SP   22
-#define IRQ_AMIGA_CIAB_FLG  23
-
-/* auto-vector interrupts */
-#define IRQ_AMIGA_AUTO      24
-#define IRQ_AMIGA_AUTO_0    24 /* This is just a dummy */
-#define IRQ_AMIGA_AUTO_1    25
-#define IRQ_AMIGA_AUTO_2    26
-#define IRQ_AMIGA_AUTO_3    27
-#define IRQ_AMIGA_AUTO_4    28
-#define IRQ_AMIGA_AUTO_5    29
-#define IRQ_AMIGA_AUTO_6    30
-#define IRQ_AMIGA_AUTO_7    31
-
-#define IRQ_FLOPPY	    IRQ_AMIGA_DSKBLK
-
-/* INTREQR masks */
-#define IRQ1_MASK   0x0007	/* INTREQR mask for IRQ 1 */
-#define IRQ2_MASK   0x0008	/* INTREQR mask for IRQ 2 */
-#define IRQ3_MASK   0x0070	/* INTREQR mask for IRQ 3 */
-#define IRQ4_MASK   0x0780	/* INTREQR mask for IRQ 4 */
-#define IRQ5_MASK   0x1800	/* INTREQR mask for IRQ 5 */
-#define IRQ6_MASK   0x2000	/* INTREQR mask for IRQ 6 */
-#define IRQ7_MASK   0x4000	/* INTREQR mask for IRQ 7 */
-
-#define IF_SETCLR   0x8000      /* set/clr bit */
-#define IF_INTEN    0x4000	/* master interrupt bit in INT* registers */
-#define IF_EXTER    0x2000	/* external level 6 and CIA B interrupt */
-#define IF_DSKSYN   0x1000	/* disk sync interrupt */
-#define IF_RBF	    0x0800	/* serial receive buffer full interrupt */
-#define IF_AUD3     0x0400	/* audio channel 3 done interrupt */
-#define IF_AUD2     0x0200	/* audio channel 2 done interrupt */
-#define IF_AUD1     0x0100	/* audio channel 1 done interrupt */
-#define IF_AUD0     0x0080	/* audio channel 0 done interrupt */
-#define IF_BLIT     0x0040	/* blitter done interrupt */
-#define IF_VERTB    0x0020	/* vertical blanking interrupt */
-#define IF_COPER    0x0010	/* copper interrupt */
-#define IF_PORTS    0x0008	/* external level 2 and CIA A interrupt */
-#define IF_SOFT     0x0004	/* software initiated interrupt */
-#define IF_DSKBLK   0x0002	/* diskblock DMA finished */
-#define IF_TBE	    0x0001	/* serial transmit buffer empty interrupt */
-
-extern void amiga_do_irq(int irq, struct pt_regs *fp);
-extern void amiga_do_irq_list(int irq, struct pt_regs *fp);
-
-/* CIA interrupt control register bits */
-
-#define CIA_ICR_TA	0x01
-#define CIA_ICR_TB	0x02
-#define CIA_ICR_ALRM	0x04
-#define CIA_ICR_SP	0x08
-#define CIA_ICR_FLG	0x10
-#define CIA_ICR_ALL	0x1f
-#define CIA_ICR_SETCLR	0x80
-
-/* to access the interrupt control registers of CIA's use only
-** these functions, they behave exactly like the amiga os routines
-*/
-
-extern struct ciabase ciaa_base, ciab_base;
-
-extern unsigned char cia_set_irq(unsigned int irq, int set);
-extern unsigned char cia_able_irq(unsigned int irq, int enable);
-
-#endif /* asm-m68k/amigaints.h */
-#endif /* __KERNEL__ */
diff --git a/include/asm-ppc/amigappc.h b/include/asm-ppc/amigappc.h
deleted file mode 100644
index 35114ce5135f..000000000000
--- a/include/asm-ppc/amigappc.h
+++ /dev/null
@@ -1,85 +0,0 @@
-/*
-** asm-ppc/amigappc.h -- This header defines some values and pointers for
-**                        the Phase 5 PowerUp card.
-**
-** Copyright 1997, 1998 by Phase5, Germany.
-**
-** This file is subject to the terms and conditions of the GNU General Public
-** License.  See the file COPYING in the main directory of this archive
-** for more details.
-**
-** Created: 7/22/97 by Jesper Skov
-*/
-
-#ifdef __KERNEL__
-#ifndef _M68K_AMIGAPPC_H
-#define _M68K_AMIGAPPC_H
-
-#ifndef __ASSEMBLY__
-
-/* #include <asm/system.h> */
-#define mb()  __asm__ __volatile__ ("sync" : : : "memory")
-
-#define APUS_WRITE(_a_, _v_)				\
-do {							\
-	(*((volatile unsigned char *)(_a_)) = (_v_));	\
-	mb();						\
-} while (0)
-
-#define APUS_READ(_a_, _v_)				\
-do {							\
-	(_v_) = (*((volatile unsigned char *)(_a_)));	\
-	mb();						\
-} while (0)
-#endif /* ndef __ASSEMBLY__ */
-
-/* Maybe add a [#ifdef WANT_ZTWOBASE] condition to amigahw.h? */
-#define zTwoBase (0x80000000)
-
-#define APUS_IPL_BASE   	(zTwoBase + 0x00f60000)
-#define APUS_REG_RESET    	(APUS_IPL_BASE + 0x00)
-#define APUS_REG_WAITSTATE    	(APUS_IPL_BASE + 0x10)
-#define APUS_REG_SHADOW    	(APUS_IPL_BASE + 0x18)
-#define APUS_REG_LOCK		(APUS_IPL_BASE + 0x20)
-#define APUS_REG_INT    	(APUS_IPL_BASE + 0x28)
-#define APUS_IPL_EMU		(APUS_IPL_BASE + 0x30)
-#define APUS_INT_LVL		(APUS_IPL_BASE + 0x38)
-
-#define REGSHADOW_SETRESET	(0x80)
-#define REGSHADOW_SELFRESET	(0x40)
-
-#define REGLOCK_SETRESET	(0x80)
-#define REGLOCK_BLACKMAGICK1	(0x40)
-#define REGLOCK_BLACKMAGICK2	(0x20)
-#define REGLOCK_BLACKMAGICK3	(0x10)
-
-#define REGWAITSTATE_SETRESET	(0x80)
-#define REGWAITSTATE_PPCW	(0x08)
-#define REGWAITSTATE_PPCR	(0x04)
-
-#define REGRESET_SETRESET	(0x80)
-#define REGRESET_PPCRESET	(0x10)
-#define REGRESET_M68KRESET	(0x08)
-#define REGRESET_AMIGARESET	(0x04)
-#define REGRESET_AUXRESET	(0x02)
-#define REGRESET_SCSIRESET	(0x01)
-
-#define REGINT_SETRESET		(0x80)
-#define REGINT_ENABLEIPL	(0x02)
-#define REGINT_INTMASTER	(0x01)
-
-#define IPLEMU_SETRESET		(0x80)
-#define IPLEMU_DISABLEINT	(0x40)
-#define IPLEMU_IPL2		(0x20)
-#define IPLEMU_IPL1		(0x10)
-#define IPLEMU_IPL0		(0x08)
-#define IPLEMU_PPCIPL2		(0x04)
-#define IPLEMU_PPCIPL1		(0x02)
-#define IPLEMU_PPCIPL0		(0x01)
-#define IPLEMU_IPLMASK		(IPLEMU_PPCIPL2|IPLEMU_PPCIPL1|IPLEMU_PPCIPL0)
-
-#define INTLVL_SETRESET         (0x80)
-#define INTLVL_MASK             (0x7f)
-
-#endif /* _M68k_AMIGAPPC_H */
-#endif /* __KERNEL__ */
diff --git a/include/asm-ppc/ans-lcd.h b/include/asm-ppc/ans-lcd.h
deleted file mode 100644
index d795b9fd2db6..000000000000
--- a/include/asm-ppc/ans-lcd.h
+++ /dev/null
@@ -1,11 +0,0 @@
-#ifndef _PPC_ANS_LCD_H
-#define _PPC_ANS_LCD_H
-
-#define ANSLCD_MINOR		156
-
-#define ANSLCD_CLEAR		0x01
-#define ANSLCD_SENDCTRL		0x02
-#define ANSLCD_SETSHORTDELAY	0x03
-#define ANSLCD_SETLONGDELAY	0x04
-
-#endif
diff --git a/include/asm-ppc/bootinfo.h b/include/asm-ppc/bootinfo.h
index 2ace4a74f263..f6ed77aee328 100644
--- a/include/asm-ppc/bootinfo.h
+++ b/include/asm-ppc/bootinfo.h
@@ -11,10 +11,6 @@
 
 #include <asm/page.h>
 
-#if defined(CONFIG_APUS) && !defined(__BOOTER__)
-#include <asm-m68k/bootinfo.h>
-#else
-
 struct bi_record {
 	unsigned long tag;		/* tag ID */
 	unsigned long size;		/* size of record (in bytes) */
@@ -44,7 +40,6 @@ bootinfo_addr(unsigned long offset)
 	return (struct bi_record *)_ALIGN((offset) + (1 << 20) - 1,
 					  (1 << 20));
 }
-#endif /* CONFIG_APUS */
 
 
 #endif /* _PPC_BOOTINFO_H */
diff --git a/include/asm-ppc/io.h b/include/asm-ppc/io.h
index 95d590423cf2..8f58231a8bc6 100644
--- a/include/asm-ppc/io.h
+++ b/include/asm-ppc/io.h
@@ -30,7 +30,7 @@
 #include <asm/mpc8xx.h>
 #elif defined(CONFIG_8260)
 #include <asm/mpc8260.h>
-#elif defined(CONFIG_APUS) || !defined(CONFIG_PCI)
+#elif !defined(CONFIG_PCI)
 #define _IO_BASE	0
 #define _ISA_MEM_BASE	0
 #define PCI_DRAM_OFFSET 0
@@ -145,24 +145,7 @@ static inline void writeb(__u8 b, volatile void __iomem *addr)
 }
 #endif
 
-#if defined(CONFIG_APUS)
-static inline __u16 readw(const volatile void __iomem *addr)
-{
-	return *(__force volatile __u16 *)(addr);
-}
-static inline __u32 readl(const volatile void __iomem *addr)
-{
-	return *(__force volatile __u32 *)(addr);
-}
-static inline void writew(__u16 b, volatile void __iomem *addr)
-{
-	*(__force volatile __u16 *)(addr) = b;
-}
-static inline void writel(__u32 b, volatile void __iomem *addr)
-{
-	*(__force volatile __u32 *)(addr) = b;
-}
-#elif defined (CONFIG_8260_PCI9)
+#if defined (CONFIG_8260_PCI9)
 /* Use macros if PCI9 workaround enabled */
 #define readw(addr) in_le16((volatile u16 *)(addr))
 #define readl(addr) in_le32((volatile u32 *)(addr))
@@ -185,7 +168,7 @@ static inline void writel(__u32 b, volatile void __iomem *addr)
 {
 	out_le32(addr, b);
 }
-#endif /* CONFIG_APUS */
+#endif /* CONFIG_8260_PCI9 */
 
 #define readb_relaxed(addr) readb(addr)
 #define readw_relaxed(addr) readw(addr)
@@ -300,13 +283,7 @@ extern __inline__ void name(unsigned int val, unsigned int port) \
 }
 
 __do_out_asm(outb, "stbx")
-#ifdef CONFIG_APUS
-__do_in_asm(inb, "lbzx")
-__do_in_asm(inw, "lhz%U1%X1")
-__do_in_asm(inl, "lwz%U1%X1")
-__do_out_asm(outl,"stw%U0%X0")
-__do_out_asm(outw, "sth%U0%X0")
-#elif defined (CONFIG_8260_PCI9)
+#if defined (CONFIG_8260_PCI9)
 /* in asm cannot be defined if PCI9 workaround is used */
 #define inb(port)		in_8((port)+___IO_BASE)
 #define inw(port)		in_le16((port)+___IO_BASE)
@@ -371,7 +348,6 @@ extern void __iomem *ioremap64(unsigned long long address, unsigned long size);
 #define ioremap_nocache(addr, size)	ioremap((addr), (size))
 extern void iounmap(volatile void __iomem *addr);
 extern unsigned long iopa(unsigned long addr);
-extern unsigned long mm_ptov(unsigned long addr) __attribute_const__;
 extern void io_block_mapping(unsigned long virt, phys_addr_t phys,
 			     unsigned int size, int flags);
 
@@ -384,24 +360,16 @@ extern void io_block_mapping(unsigned long virt, phys_addr_t phys,
  */
 extern inline unsigned long virt_to_bus(volatile void * address)
 {
-#ifndef CONFIG_APUS
         if (address == (void *)0)
 		return 0;
         return (unsigned long)address - KERNELBASE + PCI_DRAM_OFFSET;
-#else
-	return iopa ((unsigned long) address);
-#endif
 }
 
 extern inline void * bus_to_virt(unsigned long address)
 {
-#ifndef CONFIG_APUS
         if (address == 0)
 		return NULL;
         return (void *)(address - PCI_DRAM_OFFSET + KERNELBASE);
-#else
-	return (void*) mm_ptov (address);
-#endif
 }
 
 /*
@@ -410,20 +378,12 @@ extern inline void * bus_to_virt(unsigned long address)
  */
 extern inline unsigned long virt_to_phys(volatile void * address)
 {
-#ifndef CONFIG_APUS
 	return (unsigned long) address - KERNELBASE;
-#else
-	return iopa ((unsigned long) address);
-#endif
 }
 
 extern inline void * phys_to_virt(unsigned long address)
 {
-#ifndef CONFIG_APUS
 	return (void *) (address + KERNELBASE);
-#else
-	return (void*) mm_ptov (address);
-#endif
 }
 
 /*
@@ -553,4 +513,7 @@ extern void pci_iounmap(struct pci_dev *dev, void __iomem *);
 #define setbits16(_addr, _v) out_be16((_addr), in_be16(_addr) |  (_v))
 #define clrbits16(_addr, _v) out_be16((_addr), in_be16(_addr) & ~(_v))
 
+#define setbits8(_addr, _v) out_8((_addr), in_8(_addr) |  (_v))
+#define clrbits8(_addr, _v) out_8((_addr), in_8(_addr) & ~(_v))
+
 #endif /* __KERNEL__ */
diff --git a/include/asm-ppc/machdep.h b/include/asm-ppc/machdep.h
index 293a444a1d77..a20b499b0186 100644
--- a/include/asm-ppc/machdep.h
+++ b/include/asm-ppc/machdep.h
@@ -8,10 +8,6 @@
 #include <asm/setup.h>
 #include <asm/page.h>
 
-#ifdef CONFIG_APUS
-#include <asm-m68k/machdep.h>
-#endif
-
 struct pt_regs;
 struct pci_bus;	
 struct pci_dev;
diff --git a/include/asm-ppc/ocp.h b/include/asm-ppc/ocp.h
index 16dbc7d17450..1379a4f76de3 100644
--- a/include/asm-ppc/ocp.h
+++ b/include/asm-ppc/ocp.h
@@ -27,10 +27,10 @@
 #include <linux/init.h>
 #include <linux/list.h>
 #include <linux/device.h>
+#include <linux/rwsem.h>
 
 #include <asm/mmu.h>
 #include <asm/ocp_ids.h>
-#include <asm/rwsem.h>
 #include <asm/semaphore.h>
 
 #ifdef CONFIG_PPC_OCP
diff --git a/include/asm-ppc/page.h b/include/asm-ppc/page.h
index fe95c8258cf9..ad4c5a1bc9d6 100644
--- a/include/asm-ppc/page.h
+++ b/include/asm-ppc/page.h
@@ -97,62 +97,22 @@ extern void clear_user_page(void *page, unsigned long vaddr, struct page *pg);
 extern void copy_user_page(void *to, void *from, unsigned long vaddr,
 			   struct page *pg);
 
-#ifndef CONFIG_APUS
 #define PPC_MEMSTART	0
-#define PPC_PGSTART	0
 #define PPC_MEMOFFSET	PAGE_OFFSET
-#else
-extern unsigned long ppc_memstart;
-extern unsigned long ppc_pgstart;
-extern unsigned long ppc_memoffset;
-#define PPC_MEMSTART	ppc_memstart
-#define PPC_PGSTART	ppc_pgstart
-#define PPC_MEMOFFSET	ppc_memoffset
-#endif
 
-#if defined(CONFIG_APUS) && !defined(MODULE)
-/* map phys->virtual and virtual->phys for RAM pages */
-static inline unsigned long ___pa(unsigned long v)
-{
-	unsigned long p;
-	asm volatile ("1: addis %0, %1, %2;"
-		      ".section \".vtop_fixup\",\"aw\";"
-		      ".align  1;"
-		      ".long   1b;"
-		      ".previous;"
-		      : "=r" (p)
-		      : "b" (v), "K" (((-PAGE_OFFSET) >> 16) & 0xffff));
-
-	return p;
-}
-static inline void* ___va(unsigned long p)
-{
-	unsigned long v;
-	asm volatile ("1: addis %0, %1, %2;"
-		      ".section \".ptov_fixup\",\"aw\";"
-		      ".align  1;"
-		      ".long   1b;"
-		      ".previous;"
-		      : "=r" (v)
-		      : "b" (p), "K" (((PAGE_OFFSET) >> 16) & 0xffff));
-
-	return (void*) v;
-}
-#else
 #define ___pa(vaddr) ((vaddr)-PPC_MEMOFFSET)
 #define ___va(paddr) ((paddr)+PPC_MEMOFFSET)
-#endif
 
 extern int page_is_ram(unsigned long pfn);
 
 #define __pa(x) ___pa((unsigned long)(x))
 #define __va(x) ((void *)(___va((unsigned long)(x))))
 
-#define ARCH_PFN_OFFSET		(PPC_PGSTART)
+#define ARCH_PFN_OFFSET		0
 #define virt_to_page(kaddr)	pfn_to_page(__pa(kaddr) >> PAGE_SHIFT)
 #define page_to_virt(page)	__va(page_to_pfn(page) << PAGE_SHIFT)
 
-#define pfn_valid(pfn)		(((pfn) - PPC_PGSTART) < max_mapnr)
+#define pfn_valid(pfn)		((pfn) < max_mapnr)
 #define virt_addr_valid(kaddr)	pfn_valid(__pa(kaddr) >> PAGE_SHIFT)
 
 /* Pure 2^n version of get_order */
diff --git a/include/asm-ppc/pgtable.h b/include/asm-ppc/pgtable.h
index c159315d2c8f..063ad91cbbcc 100644
--- a/include/asm-ppc/pgtable.h
+++ b/include/asm-ppc/pgtable.h
@@ -765,14 +765,6 @@ extern void paging_init(void);
 #define pte_to_pgoff(pte)	(pte_val(pte) >> 3)
 #define pgoff_to_pte(off)	((pte_t) { ((off) << 3) | _PAGE_FILE })
 
-/* CONFIG_APUS */
-/* For virtual address to physical address conversion */
-extern void cache_clear(__u32 addr, int length);
-extern void cache_push(__u32 addr, int length);
-extern int mm_end_of_chunk (unsigned long addr, int len);
-extern unsigned long iopa(unsigned long addr);
-extern unsigned long mm_ptov(unsigned long addr) __attribute_const__;
-
 /* Values for nocacheflag and cmode */
 /* These are not used by the APUS kernel_map, but prevents
    compilation errors. */
diff --git a/include/asm-ppc/prom.h b/include/asm-ppc/prom.h
index 901f7fa8b2d7..71f4c996fe75 100644
--- a/include/asm-ppc/prom.h
+++ b/include/asm-ppc/prom.h
@@ -35,7 +35,6 @@ extern unsigned long sub_reloc_offset(unsigned long);
 #define machine_is_compatible(x)		0
 #define of_find_compatible_node(f, t, c)	NULL
 #define of_get_property(p, n, l)		NULL
-#define get_property(a, b, c)			of_get_property((a), (b), (c))
 
 #endif /* _PPC_PROM_H */
 #endif /* __KERNEL__ */
diff --git a/include/linux/elf.h b/include/linux/elf.h
index 8b17ffe222c4..d2da84acf45d 100644
--- a/include/linux/elf.h
+++ b/include/linux/elf.h
@@ -389,12 +389,14 @@ extern Elf64_Dyn _DYNAMIC [];
 
 #endif
 
+/* Optional callbacks to write extra ELF notes. */
 #ifndef ARCH_HAVE_EXTRA_ELF_NOTES
-static inline int arch_notes_size(void) { return 0; }
-static inline void arch_write_notes(struct file *file) { }
-
-#define ELF_CORE_EXTRA_NOTES_SIZE arch_notes_size()
-#define ELF_CORE_WRITE_EXTRA_NOTES arch_write_notes(file)
-#endif /* ARCH_HAVE_EXTRA_ELF_NOTES */
+static inline int elf_coredump_extra_notes_size(void) { return 0; }
+static inline int elf_coredump_extra_notes_write(struct file *file,
+			loff_t *foffset) { return 0; }
+#else
+extern int elf_coredump_extra_notes_size(void);
+extern int elf_coredump_extra_notes_write(struct file *file, loff_t *foffset);
+#endif
 
 #endif /* _LINUX_ELF_H */
diff --git a/include/linux/of.h b/include/linux/of.h
index 47734ffd9745..6df80e985914 100644
--- a/include/linux/of.h
+++ b/include/linux/of.h
@@ -54,7 +54,6 @@ extern int of_device_is_compatible(const struct device_node *device,
 extern const void *of_get_property(const struct device_node *node,
 				const char *name,
 				int *lenp);
-#define get_property(a, b, c)	of_get_property((a), (b), (c))
 extern int of_n_addr_cells(struct device_node *np);
 extern int of_n_size_cells(struct device_node *np);
 
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 8acae4eeaa76..3948708c42ca 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2113,8 +2113,11 @@
 #define PCI_DEVICE_ID_MPC8533		0x0031
 #define PCI_DEVICE_ID_MPC8544E		0x0032
 #define PCI_DEVICE_ID_MPC8544		0x0033
+#define PCI_DEVICE_ID_MPC8572E		0x0040
+#define PCI_DEVICE_ID_MPC8572		0x0041
 #define PCI_DEVICE_ID_MPC8641		0x7010
 #define PCI_DEVICE_ID_MPC8641D		0x7011
+#define PCI_DEVICE_ID_MPC8610		0x7018
 
 #define PCI_VENDOR_ID_PASEMI		0x1959
 
diff --git a/include/linux/xilinxfb.h b/include/linux/xilinxfb.h
new file mode 100644
index 000000000000..f2463f559fb9
--- /dev/null
+++ b/include/linux/xilinxfb.h
@@ -0,0 +1,30 @@
+/*
+ * Platform device data for Xilinx Framebuffer device
+ *
+ * Copyright 2007 Secret Lab Technologies Ltd.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef __XILINXFB_H__
+#define __XILINXFB_H__
+
+#include <linux/types.h>
+
+/* ML300/403 reference design framebuffer driver platform data struct */
+struct xilinxfb_platform_data {
+	u32 rotate_screen;	/* Flag to rotate display 180 degrees */
+	u32 screen_height_mm;	/* Physical dimentions of screen in mm */
+	u32 screen_width_mm;
+	u32 xres, yres;		/* resolution of screen in pixels */
+	u32 xvirt, yvirt;	/* resolution of memory buffer */
+
+	/* Physical address of framebuffer memory; If non-zero, driver
+	 * will use provided memory address instead of allocating one from
+	 * the consistent pool. */
+	u32 fb_phys;
+};
+
+#endif  /* __XILINXFB_H__ */