Merge tag 'spi-nor/for-5.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next

SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which
  is critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
  during the release cycle.

SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was
  taken through the SPI tree. Merge it also in spi-nor/next
  to avoid conflicts during the release cycle.
- intel-spi:
   - Add new PCI IDs.
   - Ignore the Write Disable command, the controller doesn't
     support it.
   - Fix performance regression.

1 files changed, 13 insertions, 1 deletions

diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
index af9ff2f0f1b2..159463cc659c 100644
--- a/include/linux/spi/spi-mem.h
+++ b/include/linux/spi/spi-mem.h
@@ -17,6 +17,7 @@
 	{							\
 		.buswidth = __buswidth,				\
 		.opcode = __opcode,				\
+		.nbytes = 1,					\
 	}
 
 #define SPI_MEM_OP_ADDR(__nbytes, __val, __buswidth)		\
@@ -69,11 +70,15 @@ enum spi_mem_data_dir {
 
 /**
  * struct spi_mem_op - describes a SPI memory operation
+ * @cmd.nbytes: number of opcode bytes (only 1 or 2 are valid). The opcode is
+ *		sent MSB-first.
  * @cmd.buswidth: number of IO lines used to transmit the command
  * @cmd.opcode: operation opcode
+ * @cmd.dtr: whether the command opcode should be sent in DTR mode or not
  * @addr.nbytes: number of address bytes to send. Can be zero if the operation
  *		 does not need to send an address
  * @addr.buswidth: number of IO lines used to transmit the address cycles
+ * @addr.dtr: whether the address should be sent in DTR mode or not
  * @addr.val: address value. This value is always sent MSB first on the bus.
  *	      Note that only @addr.nbytes are taken into account in this
  *	      address value, so users should make sure the value fits in the
@@ -81,7 +86,9 @@ enum spi_mem_data_dir {
  * @dummy.nbytes: number of dummy bytes to send after an opcode or address. Can
  *		  be zero if the operation does not require dummy bytes
  * @dummy.buswidth: number of IO lanes used to transmit the dummy bytes
+ * @dummy.dtr: whether the dummy bytes should be sent in DTR mode or not
  * @data.buswidth: number of IO lanes used to send/receive the data
+ * @data.dtr: whether the data should be sent in DTR mode or not
  * @data.dir: direction of the transfer
  * @data.nbytes: number of data bytes to send/receive. Can be zero if the
  *		 operation does not involve transferring data
@@ -90,23 +97,28 @@ enum spi_mem_data_dir {
  */
 struct spi_mem_op {
 	struct {
+		u8 nbytes;
 		u8 buswidth;
-		u8 opcode;
+		u8 dtr : 1;
+		u16 opcode;
 	} cmd;
 
 	struct {
 		u8 nbytes;
 		u8 buswidth;
+		u8 dtr : 1;
 		u64 val;
 	} addr;
 
 	struct {
 		u8 nbytes;
 		u8 buswidth;
+		u8 dtr : 1;
 	} dummy;
 
 	struct {
 		u8 buswidth;
+		u8 dtr : 1;
 		enum spi_mem_data_dir dir;
 		unsigned int nbytes;
 		union {