genirq: Add irq_domain-aware core IRQ handler

Calling irq_find_mapping from outside a irq_{enter,exit} section is
unsafe and produces ugly messages if CONFIG_PROVE_RCU is enabled:
If coming from the idle state, the rcu_read_lock call in irq_find_mapping
will generate an unpleasant warning:

<quote>
===============================
[ INFO: suspicious RCU usage. ]
3.16.0-rc1+ #135 Not tainted
-------------------------------
include/linux/rcupdate.h:871 rcu_read_lock() used illegally while idle!

other info that might help us debug this:

RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
1 lock held by swapper/0/0:
 #0:  (rcu_read_lock){......}, at: [<ffffffc00010206c>]
irq_find_mapping+0x4c/0x198
</quote>

As this issue is fairly widespread and involves at least three
different architectures, a possible solution is to add a new
handle_domain_irq entry point into the generic IRQ code that
the interrupt controller code can call.

This new function takes an irq_domain, and calls into irq_find_domain
inside the irq_{enter,exit} block. An additional "lookup" parameter is
used to allow non-domain architecture code to be replaced by this as well.

Interrupt controllers can then be updated to use the new mechanism.

This code is sitting behind a new CONFIG_HANDLE_DOMAIN_IRQ, as not all
architectures implement set_irq_regs (yes, mn10300, I'm looking at you...).

Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1409047421-27649-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

2 files changed, 45 insertions, 0 deletions

diff --git a/kernel/irq/Kconfig b/kernel/irq/Kconfig
index d269cecdfbf0..225086b2652e 100644
--- a/kernel/irq/Kconfig
+++ b/kernel/irq/Kconfig
@@ -55,6 +55,9 @@ config GENERIC_IRQ_CHIP
 config IRQ_DOMAIN
 	bool
 
+config HANDLE_DOMAIN_IRQ
+	bool
+
 config IRQ_DOMAIN_DEBUG
 	bool "Expose hardware/virtual IRQ mapping via debugfs"
 	depends on IRQ_DOMAIN && DEBUG_FS
diff --git a/kernel/irq/irqdesc.c b/kernel/irq/irqdesc.c
index 1487a123db5c..a1782f88f0af 100644
--- a/kernel/irq/irqdesc.c
+++ b/kernel/irq/irqdesc.c
@@ -14,6 +14,7 @@
 #include <linux/kernel_stat.h>
 #include <linux/radix-tree.h>
 #include <linux/bitmap.h>
+#include <linux/irqdomain.h>
 
 #include "internals.h"
 
@@ -336,6 +337,47 @@ int generic_handle_irq(unsigned int irq)
 }
 EXPORT_SYMBOL_GPL(generic_handle_irq);
 
+#ifdef CONFIG_HANDLE_DOMAIN_IRQ
+/**
+ * __handle_domain_irq - Invoke the handler for a HW irq belonging to a domain
+ * @domain:	The domain where to perform the lookup
+ * @hwirq:	The HW irq number to convert to a logical one
+ * @lookup:	Whether to perform the domain lookup or not
+ * @regs:	Register file coming from the low-level handling code
+ *
+ * Returns:	0 on success, or -EINVAL if conversion has failed
+ */
+int __handle_domain_irq(struct irq_domain *domain, unsigned int hwirq,
+			bool lookup, struct pt_regs *regs)
+{
+	struct pt_regs *old_regs = set_irq_regs(regs);
+	unsigned int irq = hwirq;
+	int ret = 0;
+
+	irq_enter();
+
+#ifdef CONFIG_IRQ_DOMAIN
+	if (lookup)
+		irq = irq_find_mapping(domain, hwirq);
+#endif
+
+	/*
+	 * Some hardware gives randomly wrong interrupts.  Rather
+	 * than crashing, do something sensible.
+	 */
+	if (unlikely(!irq || irq >= nr_irqs)) {
+		ack_bad_irq(irq);
+		ret = -EINVAL;
+	} else {
+		generic_handle_irq(irq);
+	}
+
+	irq_exit();
+	set_irq_regs(old_regs);
+	return ret;
+}
+#endif
+
 /* Dynamic interrupt handling */
 
 /**