diff options
-rw-r--r-- | drivers/ata/libata-scsi.c | 2 | ||||
-rw-r--r-- | drivers/ata/libata-sff.c | 2 | ||||
-rw-r--r-- | drivers/ata/pata_hpt3x2n.c | 64 | ||||
-rw-r--r-- | drivers/ata/pata_octeon_cf.c | 2 | ||||
-rw-r--r-- | drivers/ata/sata_mv.c | 144 |
5 files changed, 163 insertions, 51 deletions
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c index 1683ebda900b..f4ea5a8c325b 100644 --- a/drivers/ata/libata-scsi.c +++ b/drivers/ata/libata-scsi.c @@ -3022,7 +3022,7 @@ static inline ata_xlat_func_t ata_get_xlat_func(struct ata_device *dev, u8 cmd) case WRITE_16: return ata_scsi_rw_xlat; - case 0x93 /*WRITE_SAME_16*/: + case WRITE_SAME_16: return ata_scsi_write_same_xlat; case SYNCHRONIZE_CACHE: diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c index efa8773bef5a..741065c9da67 100644 --- a/drivers/ata/libata-sff.c +++ b/drivers/ata/libata-sff.c @@ -2275,7 +2275,7 @@ void ata_sff_drain_fifo(struct ata_queued_cmd *qc) ap = qc->ap; /* Drain up to 64K of data before we give up this recovery method */ for (count = 0; (ap->ops->sff_check_status(ap) & ATA_DRQ) - && count < 32768; count++) + && count < 65536; count += 2) ioread16(ap->ioaddr.data_addr); /* Can become DEBUG later */ diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c index 9a09a1b11ca5..dd26bc73bd9a 100644 --- a/drivers/ata/pata_hpt3x2n.c +++ b/drivers/ata/pata_hpt3x2n.c @@ -8,7 +8,7 @@ * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> * Portions Copyright (C) 2001 Sun Microsystems, Inc. * Portions Copyright (C) 2003 Red Hat Inc - * Portions Copyright (C) 2005-2007 MontaVista Software, Inc. + * Portions Copyright (C) 2005-2009 MontaVista Software, Inc. * * * TODO @@ -25,7 +25,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_hpt3x2n" -#define DRV_VERSION "0.3.7" +#define DRV_VERSION "0.3.8" enum { HPT_PCI_FAST = (1 << 31), @@ -264,7 +264,7 @@ static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc) static void hpt3x2n_set_clock(struct ata_port *ap, int source) { - void __iomem *bmdma = ap->ioaddr.bmdma_addr; + void __iomem *bmdma = ap->ioaddr.bmdma_addr - ap->port_no * 8; /* Tristate the bus */ iowrite8(0x80, bmdma+0x73); @@ -274,9 +274,9 @@ static void hpt3x2n_set_clock(struct ata_port *ap, int source) iowrite8(source, bmdma+0x7B); iowrite8(0xC0, bmdma+0x79); - /* Reset state machines */ - iowrite8(0x37, bmdma+0x70); - iowrite8(0x37, bmdma+0x74); + /* Reset state machines, avoid enabling the disabled channels */ + iowrite8(ioread8(bmdma+0x70) | 0x32, bmdma+0x70); + iowrite8(ioread8(bmdma+0x74) | 0x32, bmdma+0x74); /* Complete reset */ iowrite8(0x00, bmdma+0x79); @@ -286,21 +286,10 @@ static void hpt3x2n_set_clock(struct ata_port *ap, int source) iowrite8(0x00, bmdma+0x77); } -/* Check if our partner interface is busy */ - -static int hpt3x2n_pair_idle(struct ata_port *ap) -{ - struct ata_host *host = ap->host; - struct ata_port *pair = host->ports[ap->port_no ^ 1]; - - if (pair->hsm_task_state == HSM_ST_IDLE) - return 1; - return 0; -} - static int hpt3x2n_use_dpll(struct ata_port *ap, int writing) { long flags = (long)ap->host->private_data; + /* See if we should use the DPLL */ if (writing) return USE_DPLL; /* Needed for write */ @@ -309,20 +298,35 @@ static int hpt3x2n_use_dpll(struct ata_port *ap, int writing) return 0; } +static int hpt3x2n_qc_defer(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_port *alt = ap->host->ports[ap->port_no ^ 1]; + int rc, flags = (long)ap->host->private_data; + int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE); + + /* First apply the usual rules */ + rc = ata_std_qc_defer(qc); + if (rc != 0) + return rc; + + if ((flags & USE_DPLL) != dpll && alt->qc_active) + return ATA_DEFER_PORT; + return 0; +} + static unsigned int hpt3x2n_qc_issue(struct ata_queued_cmd *qc) { - struct ata_taskfile *tf = &qc->tf; struct ata_port *ap = qc->ap; int flags = (long)ap->host->private_data; + int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE); - if (hpt3x2n_pair_idle(ap)) { - int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE)); - if ((flags & USE_DPLL) != dpll) { - if (dpll == 1) - hpt3x2n_set_clock(ap, 0x21); - else - hpt3x2n_set_clock(ap, 0x23); - } + if ((flags & USE_DPLL) != dpll) { + flags &= ~USE_DPLL; + flags |= dpll; + ap->host->private_data = (void *)(long)flags; + + hpt3x2n_set_clock(ap, dpll ? 0x21 : 0x23); } return ata_sff_qc_issue(qc); } @@ -339,6 +343,8 @@ static struct ata_port_operations hpt3x2n_port_ops = { .inherits = &ata_bmdma_port_ops, .bmdma_stop = hpt3x2n_bmdma_stop, + + .qc_defer = hpt3x2n_qc_defer, .qc_issue = hpt3x2n_qc_issue, .cable_detect = hpt3x2n_cable_detect, @@ -454,7 +460,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) unsigned int f_low, f_high; int adjust; unsigned long iobase = pci_resource_start(dev, 4); - void *hpriv = NULL; + void *hpriv = (void *)USE_DPLL; int rc; rc = pcim_enable_device(dev); @@ -539,7 +545,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) /* Set our private data up. We only need a few flags so we use it directly */ if (pci_mhz > 60) { - hpriv = (void *)PCI66; + hpriv = (void *)(PCI66 | USE_DPLL); /* * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in * the MISC. register to stretch the UltraDMA Tss timing. diff --git a/drivers/ata/pata_octeon_cf.c b/drivers/ata/pata_octeon_cf.c index d6f69561dc86..37ef416c1242 100644 --- a/drivers/ata/pata_octeon_cf.c +++ b/drivers/ata/pata_octeon_cf.c @@ -853,7 +853,7 @@ static int __devinit octeon_cf_probe(struct platform_device *pdev) return -EINVAL; cs1 = devm_ioremap_nocache(&pdev->dev, res_cs1->start, - res_cs0->end - res_cs1->start + 1); + resource_size(res_cs1)); if (!cs1) return -ENOMEM; diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index a8a7be0d06ff..df8ee325d3ca 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -59,6 +59,7 @@ #include <linux/dmapool.h> #include <linux/dma-mapping.h> #include <linux/device.h> +#include <linux/clk.h> #include <linux/platform_device.h> #include <linux/ata_platform.h> #include <linux/mbus.h> @@ -538,6 +539,7 @@ struct mv_port_signal { struct mv_host_priv { u32 hp_flags; + unsigned int board_idx; u32 main_irq_mask; struct mv_port_signal signal[8]; const struct mv_hw_ops *ops; @@ -548,6 +550,10 @@ struct mv_host_priv { u32 irq_cause_offset; u32 irq_mask_offset; u32 unmask_all_irqs; + +#if defined(CONFIG_HAVE_CLK) + struct clk *clk; +#endif /* * These consistent DMA memory pools give us guaranteed * alignment for hardware-accessed data structures, @@ -2775,7 +2781,7 @@ static void mv_port_intr(struct ata_port *ap, u32 port_cause) struct mv_port_priv *pp; int edma_was_enabled; - if (!ap || (ap->flags & ATA_FLAG_DISABLED)) { + if (ap->flags & ATA_FLAG_DISABLED) { mv_unexpected_intr(ap, 0); return; } @@ -3393,7 +3399,7 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv, ZERO(0x024); /* respq outp */ ZERO(0x020); /* respq inp */ ZERO(0x02c); /* test control */ - writel(0xbc, port_mmio + EDMA_IORDY_TMOUT); + writel(0x800, port_mmio + EDMA_IORDY_TMOUT); } #undef ZERO @@ -3854,7 +3860,6 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) /** * mv_init_host - Perform some early initialization of the host. * @host: ATA host to initialize - * @board_idx: controller index * * If possible, do an early global reset of the host. Then do * our port init and clear/unmask all/relevant host interrupts. @@ -3862,13 +3867,13 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) * LOCKING: * Inherited from caller. */ -static int mv_init_host(struct ata_host *host, unsigned int board_idx) +static int mv_init_host(struct ata_host *host) { int rc = 0, n_hc, port, hc; struct mv_host_priv *hpriv = host->private_data; void __iomem *mmio = hpriv->base; - rc = mv_chip_id(host, board_idx); + rc = mv_chip_id(host, hpriv->board_idx); if (rc) goto done; @@ -3905,14 +3910,6 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx) void __iomem *port_mmio = mv_port_base(mmio, port); mv_port_init(&ap->ioaddr, port_mmio); - -#ifdef CONFIG_PCI - if (!IS_SOC(hpriv)) { - unsigned int offset = port_mmio - mmio; - ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio"); - ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port"); - } -#endif } for (hc = 0; hc < n_hc; hc++) { @@ -4035,12 +4032,21 @@ static int mv_platform_probe(struct platform_device *pdev) return -ENOMEM; host->private_data = hpriv; hpriv->n_ports = n_ports; + hpriv->board_idx = chip_soc; host->iomap = NULL; hpriv->base = devm_ioremap(&pdev->dev, res->start, resource_size(res)); hpriv->base -= SATAHC0_REG_BASE; +#if defined(CONFIG_HAVE_CLK) + hpriv->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(hpriv->clk)) + dev_notice(&pdev->dev, "cannot get clkdev\n"); + else + clk_enable(hpriv->clk); +#endif + /* * (Re-)program MBUS remapping windows if we are asked to. */ @@ -4049,12 +4055,12 @@ static int mv_platform_probe(struct platform_device *pdev) rc = mv_create_dma_pools(hpriv, &pdev->dev); if (rc) - return rc; + goto err; /* initialize adapter */ - rc = mv_init_host(host, chip_soc); + rc = mv_init_host(host); if (rc) - return rc; + goto err; dev_printk(KERN_INFO, &pdev->dev, "slots %u ports %d\n", (unsigned)MV_MAX_Q_DEPTH, @@ -4062,6 +4068,15 @@ static int mv_platform_probe(struct platform_device *pdev) return ata_host_activate(host, platform_get_irq(pdev, 0), mv_interrupt, IRQF_SHARED, &mv6_sht); +err: +#if defined(CONFIG_HAVE_CLK) + if (!IS_ERR(hpriv->clk)) { + clk_disable(hpriv->clk); + clk_put(hpriv->clk); + } +#endif + + return rc; } /* @@ -4076,14 +4091,66 @@ static int __devexit mv_platform_remove(struct platform_device *pdev) { struct device *dev = &pdev->dev; struct ata_host *host = dev_get_drvdata(dev); - +#if defined(CONFIG_HAVE_CLK) + struct mv_host_priv *hpriv = host->private_data; +#endif ata_host_detach(host); + +#if defined(CONFIG_HAVE_CLK) + if (!IS_ERR(hpriv->clk)) { + clk_disable(hpriv->clk); + clk_put(hpriv->clk); + } +#endif return 0; } +#ifdef CONFIG_PM +static int mv_platform_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + if (host) + return ata_host_suspend(host, state); + else + return 0; +} + +static int mv_platform_resume(struct platform_device *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + int ret; + + if (host) { + struct mv_host_priv *hpriv = host->private_data; + const struct mv_sata_platform_data *mv_platform_data = \ + pdev->dev.platform_data; + /* + * (Re-)program MBUS remapping windows if we are asked to. + */ + if (mv_platform_data->dram != NULL) + mv_conf_mbus_windows(hpriv, mv_platform_data->dram); + + /* initialize adapter */ + ret = mv_init_host(host); + if (ret) { + printk(KERN_ERR DRV_NAME ": Error during HW init\n"); + return ret; + } + ata_host_resume(host); + } + + return 0; +} +#else +#define mv_platform_suspend NULL +#define mv_platform_resume NULL +#endif + static struct platform_driver mv_platform_driver = { .probe = mv_platform_probe, .remove = __devexit_p(mv_platform_remove), + .suspend = mv_platform_suspend, + .resume = mv_platform_resume, .driver = { .name = DRV_NAME, .owner = THIS_MODULE, @@ -4094,6 +4161,9 @@ static struct platform_driver mv_platform_driver = { #ifdef CONFIG_PCI static int mv_pci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); +#ifdef CONFIG_PM +static int mv_pci_device_resume(struct pci_dev *pdev); +#endif static struct pci_driver mv_pci_driver = { @@ -4101,6 +4171,11 @@ static struct pci_driver mv_pci_driver = { .id_table = mv_pci_tbl, .probe = mv_pci_init_one, .remove = ata_pci_remove_one, +#ifdef CONFIG_PM + .suspend = ata_pci_device_suspend, + .resume = mv_pci_device_resume, +#endif + }; /* move to PCI layer or libata core? */ @@ -4194,7 +4269,7 @@ static int mv_pci_init_one(struct pci_dev *pdev, const struct ata_port_info *ppi[] = { &mv_port_info[board_idx], NULL }; struct ata_host *host; struct mv_host_priv *hpriv; - int n_ports, rc; + int n_ports, port, rc; if (!printed_version++) dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n"); @@ -4208,6 +4283,7 @@ static int mv_pci_init_one(struct pci_dev *pdev, return -ENOMEM; host->private_data = hpriv; hpriv->n_ports = n_ports; + hpriv->board_idx = board_idx; /* acquire resources */ rc = pcim_enable_device(pdev); @@ -4230,8 +4306,17 @@ static int mv_pci_init_one(struct pci_dev *pdev, if (rc) return rc; + for (port = 0; port < host->n_ports; port++) { + struct ata_port *ap = host->ports[port]; + void __iomem *port_mmio = mv_port_base(hpriv->base, port); + unsigned int offset = port_mmio - hpriv->base; + + ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio"); + ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port"); + } + /* initialize adapter */ - rc = mv_init_host(host, board_idx); + rc = mv_init_host(host); if (rc) return rc; @@ -4247,6 +4332,27 @@ static int mv_pci_init_one(struct pci_dev *pdev, return ata_host_activate(host, pdev->irq, mv_interrupt, IRQF_SHARED, IS_GEN_I(hpriv) ? &mv5_sht : &mv6_sht); } + +#ifdef CONFIG_PM +static int mv_pci_device_resume(struct pci_dev *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + int rc; + + rc = ata_pci_device_do_resume(pdev); + if (rc) + return rc; + + /* initialize adapter */ + rc = mv_init_host(host); + if (rc) + return rc; + + ata_host_resume(host); + + return 0; +} +#endif #endif static int mv_platform_probe(struct platform_device *pdev); |