diff options
| -rw-r--r-- | drivers/scsi/hpsa.c | 81 |
1 files changed, 15 insertions, 66 deletions
diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c index cfd30adc3f18..82b94e2c745b 100644 --- a/drivers/scsi/hpsa.c +++ b/drivers/scsi/hpsa.c @@ -3053,38 +3053,6 @@ static __devinit int hpsa_message(struct pci_dev *pdev, unsigned char opcode, #define hpsa_soft_reset_controller(p) hpsa_message(p, 1, 0) #define hpsa_noop(p) hpsa_message(p, 3, 0) -static __devinit int hpsa_reset_msi(struct pci_dev *pdev) -{ -/* the #defines are stolen from drivers/pci/msi.h. */ -#define msi_control_reg(base) (base + PCI_MSI_FLAGS) -#define PCI_MSIX_FLAGS_ENABLE (1 << 15) - - int pos; - u16 control = 0; - - pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); - if (pos) { - pci_read_config_word(pdev, msi_control_reg(pos), &control); - if (control & PCI_MSI_FLAGS_ENABLE) { - dev_info(&pdev->dev, "resetting MSI\n"); - pci_write_config_word(pdev, msi_control_reg(pos), - control & ~PCI_MSI_FLAGS_ENABLE); - } - } - - pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX); - if (pos) { - pci_read_config_word(pdev, msi_control_reg(pos), &control); - if (control & PCI_MSIX_FLAGS_ENABLE) { - dev_info(&pdev->dev, "resetting MSI-X\n"); - pci_write_config_word(pdev, msi_control_reg(pos), - control & ~PCI_MSIX_FLAGS_ENABLE); - } - } - - return 0; -} - static int hpsa_controller_hard_reset(struct pci_dev *pdev, void * __iomem vaddr, bool use_doorbell) { @@ -3140,17 +3108,17 @@ static int hpsa_controller_hard_reset(struct pci_dev *pdev, */ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev) { - u16 saved_config_space[32]; u64 cfg_offset; u32 cfg_base_addr; u64 cfg_base_addr_index; void __iomem *vaddr; unsigned long paddr; u32 misc_fw_support, active_transport; - int rc, i; + int rc; struct CfgTable __iomem *cfgtable; bool use_doorbell; u32 board_id; + u16 command_register; /* For controllers as old as the P600, this is very nearly * the same thing as @@ -3160,14 +3128,6 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev) * pci_set_power_state(pci_dev, PCI_D0); * pci_restore_state(pci_dev); * - * but we can't use these nice canned kernel routines on - * kexec, because they also check the MSI/MSI-X state in PCI - * configuration space and do the wrong thing when it is - * set/cleared. Also, the pci_save/restore_state functions - * violate the ordering requirements for restoring the - * configuration space from the CCISS document (see the - * comment below). So we roll our own .... - * * For controllers newer than the P600, the pci power state * method of resetting doesn't work so we have another way * using the doorbell register. @@ -3184,9 +3144,13 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev) if (board_id == 0x409C0E11 || board_id == 0x409D0E11) return -ENOTSUPP; - for (i = 0; i < 32; i++) - pci_read_config_word(pdev, 2*i, &saved_config_space[i]); - + /* Save the PCI command register */ + pci_read_config_word(pdev, 4, &command_register); + /* Turn the board off. This is so that later pci_restore_state() + * won't turn the board on before the rest of config space is ready. + */ + pci_disable_device(pdev); + pci_save_state(pdev); /* find the first memory BAR, so we can find the cfg table */ rc = hpsa_pci_find_memory_BAR(pdev, &paddr); @@ -3212,30 +3176,17 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev) misc_fw_support = readl(&cfgtable->misc_fw_support); use_doorbell = misc_fw_support & MISC_FW_DOORBELL_RESET; - /* The doorbell reset seems to cause lockups on some Smart - * Arrays (e.g. P410, P410i, maybe others). Until this is - * fixed or at least isolated, avoid the doorbell reset. - */ - use_doorbell = 0; - rc = hpsa_controller_hard_reset(pdev, vaddr, use_doorbell); if (rc) goto unmap_cfgtable; - /* Restore the PCI configuration space. The Open CISS - * Specification says, "Restore the PCI Configuration - * Registers, offsets 00h through 60h. It is important to - * restore the command register, 16-bits at offset 04h, - * last. Do not restore the configuration status register, - * 16-bits at offset 06h." Note that the offset is 2*i. - */ - for (i = 0; i < 32; i++) { - if (i == 2 || i == 3) - continue; - pci_write_config_word(pdev, 2*i, saved_config_space[i]); + pci_restore_state(pdev); + rc = pci_enable_device(pdev); + if (rc) { + dev_warn(&pdev->dev, "failed to enable device.\n"); + goto unmap_cfgtable; } - wmb(); - pci_write_config_word(pdev, 4, saved_config_space[2]); + pci_write_config_word(pdev, 4, command_register); /* Some devices (notably the HP Smart Array 5i Controller) need a little pause here */ @@ -3732,8 +3683,6 @@ static __devinit int hpsa_init_reset_devices(struct pci_dev *pdev) return 0; /* just try to do the kdump anyhow. */ if (rc) return -ENODEV; - if (hpsa_reset_msi(pdev)) - return -ENODEV; /* Now try to get the controller to respond to a no-op */ for (i = 0; i < HPSA_POST_RESET_NOOP_RETRIES; i++) { |