diff options
| -rw-r--r-- | Documentation/spi/ep93xx_spi | 105 | ||||
| -rw-r--r-- | arch/arm/mach-ep93xx/edb93xx.c | 31 | ||||
| -rw-r--r-- | arch/arm/mach-ep93xx/simone.c | 63 | ||||
| -rw-r--r-- | arch/arm/mach-ep93xx/vision_ep9307.c | 88 | ||||
| -rw-r--r-- | drivers/spi/spi-ep93xx.c | 139 | ||||
| -rw-r--r-- | include/linux/platform_data/spi-ep93xx.h | 17 |
6 files changed, 74 insertions, 369 deletions
diff --git a/Documentation/spi/ep93xx_spi b/Documentation/spi/ep93xx_spi deleted file mode 100644 index 832ddce6e5fb..000000000000 --- a/Documentation/spi/ep93xx_spi +++ /dev/null @@ -1,105 +0,0 @@ -Cirrus EP93xx SPI controller driver HOWTO -========================================= - -ep93xx_spi driver brings SPI master support for EP93xx SPI controller. Chip -selects are implemented with GPIO lines. - -NOTE: If possible, don't use SFRMOUT (SFRM1) signal as a chip select. It will -not work correctly (it cannot be controlled by software). Use GPIO lines -instead. - -Sample configuration -==================== - -Typically driver configuration is done in platform board files (the files under -arch/arm/mach-ep93xx/*.c). In this example we configure MMC over SPI through -this driver on TS-7260 board. You can adapt the code to suit your needs. - -This example uses EGPIO9 as SD/MMC card chip select (this is wired in DIO1 -header on the board). - -You need to select CONFIG_MMC_SPI to use mmc_spi driver. - -arch/arm/mach-ep93xx/ts72xx.c: - -... -#include <linux/gpio.h> -#include <linux/spi/spi.h> - -#include <linux/platform_data/spi-ep93xx.h> - -/* this is our GPIO line used for chip select */ -#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO9 - -static int ts72xx_mmc_spi_setup(struct spi_device *spi) -{ - int err; - - err = gpio_request(MMC_CHIP_SELECT_GPIO, spi->modalias); - if (err) - return err; - - gpio_direction_output(MMC_CHIP_SELECT_GPIO, 1); - - return 0; -} - -static void ts72xx_mmc_spi_cleanup(struct spi_device *spi) -{ - gpio_set_value(MMC_CHIP_SELECT_GPIO, 1); - gpio_direction_input(MMC_CHIP_SELECT_GPIO); - gpio_free(MMC_CHIP_SELECT_GPIO); -} - -static void ts72xx_mmc_spi_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(MMC_CHIP_SELECT_GPIO, value); -} - -static struct ep93xx_spi_chip_ops ts72xx_mmc_spi_ops = { - .setup = ts72xx_mmc_spi_setup, - .cleanup = ts72xx_mmc_spi_cleanup, - .cs_control = ts72xx_mmc_spi_cs_control, -}; - -static struct spi_board_info ts72xx_spi_devices[] __initdata = { - { - .modalias = "mmc_spi", - .controller_data = &ts72xx_mmc_spi_ops, - /* - * We use 10 MHz even though the maximum is 7.4 MHz. The driver - * will limit it automatically to max. frequency. - */ - .max_speed_hz = 10 * 1000 * 1000, - .bus_num = 0, - .chip_select = 0, - .mode = SPI_MODE_0, - }, -}; - -static struct ep93xx_spi_info ts72xx_spi_info = { - .num_chipselect = ARRAY_SIZE(ts72xx_spi_devices), -}; - -static void __init ts72xx_init_machine(void) -{ - ... - ep93xx_register_spi(&ts72xx_spi_info, ts72xx_spi_devices, - ARRAY_SIZE(ts72xx_spi_devices)); -} - -The driver can use DMA for the transfers also. In this case ts72xx_spi_info -becomes: - -static struct ep93xx_spi_info ts72xx_spi_info = { - .num_chipselect = ARRAY_SIZE(ts72xx_spi_devices), - .use_dma = true; -}; - -Note that CONFIG_EP93XX_DMA should be enabled as well. - -Thanks to -========= -Martin Guy, H. Hartley Sweeten and others who helped me during development of -the driver. Simplemachines.it donated me a Sim.One board which I used testing -the driver on EP9307. diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c index ad92d9f7e4df..0ac176386789 100644 --- a/arch/arm/mach-ep93xx/edb93xx.c +++ b/arch/arm/mach-ep93xx/edb93xx.c @@ -27,7 +27,6 @@ #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> -#include <linux/gpio.h> #include <linux/i2c.h> #include <linux/i2c-gpio.h> #include <linux/spi/spi.h> @@ -106,33 +105,10 @@ static struct cs4271_platform_data edb93xx_cs4271_data = { .gpio_nreset = -EINVAL, /* filled in later */ }; -static int edb93xx_cs4271_hw_setup(struct spi_device *spi) -{ - return gpio_request_one(EP93XX_GPIO_LINE_EGPIO6, - GPIOF_OUT_INIT_HIGH, spi->modalias); -} - -static void edb93xx_cs4271_hw_cleanup(struct spi_device *spi) -{ - gpio_free(EP93XX_GPIO_LINE_EGPIO6); -} - -static void edb93xx_cs4271_hw_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(EP93XX_GPIO_LINE_EGPIO6, value); -} - -static struct ep93xx_spi_chip_ops edb93xx_cs4271_hw = { - .setup = edb93xx_cs4271_hw_setup, - .cleanup = edb93xx_cs4271_hw_cleanup, - .cs_control = edb93xx_cs4271_hw_cs_control, -}; - static struct spi_board_info edb93xx_spi_board_info[] __initdata = { { .modalias = "cs4271", .platform_data = &edb93xx_cs4271_data, - .controller_data = &edb93xx_cs4271_hw, .max_speed_hz = 6000000, .bus_num = 0, .chip_select = 0, @@ -140,8 +116,13 @@ static struct spi_board_info edb93xx_spi_board_info[] __initdata = { }, }; +static int edb93xx_spi_chipselects[] __initdata = { + EP93XX_GPIO_LINE_EGPIO6, +}; + static struct ep93xx_spi_info edb93xx_spi_info __initdata = { - .num_chipselect = ARRAY_SIZE(edb93xx_spi_board_info), + .chipselect = edb93xx_spi_chipselects, + .num_chipselect = ARRAY_SIZE(edb93xx_spi_chipselects), }; static void __init edb93xx_register_spi(void) diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c index 7bb540c421ee..c7a40f245892 100644 --- a/arch/arm/mach-ep93xx/simone.c +++ b/arch/arm/mach-ep93xx/simone.c @@ -49,56 +49,6 @@ static struct ep93xxfb_mach_info __initdata simone_fb_info = { #define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0 /* - * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes - * low between multi-message command blocks. From v1.4, it uses a GPIO instead. - * v1.3 parts will still work, since the signal on SFRMOUT is automatic. - */ -#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO1 - -/* - * MMC SPI chip select GPIO handling. If you are using SFRMOUT (SFRM1) signal, - * you can leave these empty and pass NULL as .controller_data. - */ - -static int simone_mmc_spi_setup(struct spi_device *spi) -{ - unsigned int gpio = MMC_CHIP_SELECT_GPIO; - int err; - - err = gpio_request(gpio, spi->modalias); - if (err) - return err; - - err = gpio_direction_output(gpio, 1); - if (err) { - gpio_free(gpio); - return err; - } - - return 0; -} - -static void simone_mmc_spi_cleanup(struct spi_device *spi) -{ - unsigned int gpio = MMC_CHIP_SELECT_GPIO; - - gpio_set_value(gpio, 1); - gpio_direction_input(gpio); - gpio_free(gpio); -} - -static void simone_mmc_spi_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(MMC_CHIP_SELECT_GPIO, value); -} - -static struct ep93xx_spi_chip_ops simone_mmc_spi_ops = { - .setup = simone_mmc_spi_setup, - .cleanup = simone_mmc_spi_cleanup, - .cs_control = simone_mmc_spi_cs_control, -}; - -/* * MMC card detection GPIO setup. */ @@ -152,7 +102,6 @@ static struct mmc_spi_platform_data simone_mmc_spi_data = { static struct spi_board_info simone_spi_devices[] __initdata = { { .modalias = "mmc_spi", - .controller_data = &simone_mmc_spi_ops, .platform_data = &simone_mmc_spi_data, /* * We use 10 MHz even though the maximum is 3.7 MHz. The driver @@ -165,8 +114,18 @@ static struct spi_board_info simone_spi_devices[] __initdata = { }, }; +/* + * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes + * low between multi-message command blocks. From v1.4, it uses a GPIO instead. + * v1.3 parts will still work, since the signal on SFRMOUT is automatic. + */ +static int simone_spi_chipselects[] __initdata = { + EP93XX_GPIO_LINE_EGPIO1, +}; + static struct ep93xx_spi_info simone_spi_info __initdata = { - .num_chipselect = ARRAY_SIZE(simone_spi_devices), + .chipselect = simone_spi_chipselects, + .num_chipselect = ARRAY_SIZE(simone_spi_chipselects), .use_dma = 1, }; diff --git a/arch/arm/mach-ep93xx/vision_ep9307.c b/arch/arm/mach-ep93xx/vision_ep9307.c index 5cced5988498..1daf9441058c 100644 --- a/arch/arm/mach-ep93xx/vision_ep9307.c +++ b/arch/arm/mach-ep93xx/vision_ep9307.c @@ -175,33 +175,9 @@ static struct cs4271_platform_data vision_cs4271_data = { .gpio_nreset = EP93XX_GPIO_LINE_H(2), }; -static int vision_cs4271_hw_setup(struct spi_device *spi) -{ - return gpio_request_one(EP93XX_GPIO_LINE_EGPIO6, - GPIOF_OUT_INIT_HIGH, spi->modalias); -} - -static void vision_cs4271_hw_cleanup(struct spi_device *spi) -{ - gpio_free(EP93XX_GPIO_LINE_EGPIO6); -} - -static void vision_cs4271_hw_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(EP93XX_GPIO_LINE_EGPIO6, value); -} - -static struct ep93xx_spi_chip_ops vision_cs4271_hw = { - .setup = vision_cs4271_hw_setup, - .cleanup = vision_cs4271_hw_cleanup, - .cs_control = vision_cs4271_hw_cs_control, -}; - /************************************************************************* * SPI Flash *************************************************************************/ -#define VISION_SPI_FLASH_CS EP93XX_GPIO_LINE_EGPIO7 - static struct mtd_partition vision_spi_flash_partitions[] = { { .name = "SPI bootstrap", @@ -224,68 +200,20 @@ static struct flash_platform_data vision_spi_flash_data = { .nr_parts = ARRAY_SIZE(vision_spi_flash_partitions), }; -static int vision_spi_flash_hw_setup(struct spi_device *spi) -{ - return gpio_request_one(VISION_SPI_FLASH_CS, GPIOF_INIT_HIGH, - spi->modalias); -} - -static void vision_spi_flash_hw_cleanup(struct spi_device *spi) -{ - gpio_free(VISION_SPI_FLASH_CS); -} - -static void vision_spi_flash_hw_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(VISION_SPI_FLASH_CS, value); -} - -static struct ep93xx_spi_chip_ops vision_spi_flash_hw = { - .setup = vision_spi_flash_hw_setup, - .cleanup = vision_spi_flash_hw_cleanup, - .cs_control = vision_spi_flash_hw_cs_control, -}; - /************************************************************************* * SPI SD/MMC host *************************************************************************/ -#define VISION_SPI_MMC_CS EP93XX_GPIO_LINE_G(2) -#define VISION_SPI_MMC_WP EP93XX_GPIO_LINE_F(0) -#define VISION_SPI_MMC_CD EP93XX_GPIO_LINE_EGPIO15 - static struct mmc_spi_platform_data vision_spi_mmc_data = { .detect_delay = 100, .powerup_msecs = 100, .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, .flags = MMC_SPI_USE_CD_GPIO | MMC_SPI_USE_RO_GPIO, - .cd_gpio = VISION_SPI_MMC_CD, + .cd_gpio = EP93XX_GPIO_LINE_EGPIO15, .cd_debounce = 1, - .ro_gpio = VISION_SPI_MMC_WP, + .ro_gpio = EP93XX_GPIO_LINE_F(0), .caps2 = MMC_CAP2_RO_ACTIVE_HIGH, }; -static int vision_spi_mmc_hw_setup(struct spi_device *spi) -{ - return gpio_request_one(VISION_SPI_MMC_CS, GPIOF_INIT_HIGH, - spi->modalias); -} - -static void vision_spi_mmc_hw_cleanup(struct spi_device *spi) -{ - gpio_free(VISION_SPI_MMC_CS); -} - -static void vision_spi_mmc_hw_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(VISION_SPI_MMC_CS, value); -} - -static struct ep93xx_spi_chip_ops vision_spi_mmc_hw = { - .setup = vision_spi_mmc_hw_setup, - .cleanup = vision_spi_mmc_hw_cleanup, - .cs_control = vision_spi_mmc_hw_cs_control, -}; - /************************************************************************* * SPI Bus *************************************************************************/ @@ -293,7 +221,6 @@ static struct spi_board_info vision_spi_board_info[] __initdata = { { .modalias = "cs4271", .platform_data = &vision_cs4271_data, - .controller_data = &vision_cs4271_hw, .max_speed_hz = 6000000, .bus_num = 0, .chip_select = 0, @@ -301,7 +228,6 @@ static struct spi_board_info vision_spi_board_info[] __initdata = { }, { .modalias = "sst25l", .platform_data = &vision_spi_flash_data, - .controller_data = &vision_spi_flash_hw, .max_speed_hz = 20000000, .bus_num = 0, .chip_select = 1, @@ -309,7 +235,6 @@ static struct spi_board_info vision_spi_board_info[] __initdata = { }, { .modalias = "mmc_spi", .platform_data = &vision_spi_mmc_data, - .controller_data = &vision_spi_mmc_hw, .max_speed_hz = 20000000, .bus_num = 0, .chip_select = 2, @@ -317,8 +242,15 @@ static struct spi_board_info vision_spi_board_info[] __initdata = { }, }; +static int vision_spi_chipselects[] __initdata = { + EP93XX_GPIO_LINE_EGPIO6, + EP93XX_GPIO_LINE_EGPIO7, + EP93XX_GPIO_LINE_G(2), +}; + static struct ep93xx_spi_info vision_spi_master __initdata = { - .num_chipselect = ARRAY_SIZE(vision_spi_board_info), + .chipselect = vision_spi_chipselects, + .num_chipselect = ARRAY_SIZE(vision_spi_chipselects), .use_dma = 1, }; diff --git a/drivers/spi/spi-ep93xx.c b/drivers/spi/spi-ep93xx.c index 17a6387e20b5..b5d766064b7b 100644 --- a/drivers/spi/spi-ep93xx.c +++ b/drivers/spi/spi-ep93xx.c @@ -28,6 +28,7 @@ #include <linux/platform_device.h> #include <linux/sched.h> #include <linux/scatterlist.h> +#include <linux/gpio.h> #include <linux/spi/spi.h> #include <linux/platform_data/dma-ep93xx.h> @@ -107,16 +108,6 @@ struct ep93xx_spi { void *zeropage; }; -/** - * struct ep93xx_spi_chip - SPI device hardware settings - * @spi: back pointer to the SPI device - * @ops: private chip operations - */ -struct ep93xx_spi_chip { - const struct spi_device *spi; - struct ep93xx_spi_chip_ops *ops; -}; - /* converts bits per word to CR0.DSS value */ #define bits_per_word_to_dss(bpw) ((bpw) - 1) @@ -229,104 +220,36 @@ static int ep93xx_spi_calc_divisors(const struct ep93xx_spi *espi, return -EINVAL; } -static void ep93xx_spi_cs_control(struct spi_device *spi, bool control) -{ - struct ep93xx_spi_chip *chip = spi_get_ctldata(spi); - int value = (spi->mode & SPI_CS_HIGH) ? control : !control; - - if (chip->ops && chip->ops->cs_control) - chip->ops->cs_control(spi, value); -} - -/** - * ep93xx_spi_setup() - setup an SPI device - * @spi: SPI device to setup - * - * This function sets up SPI device mode, speed etc. Can be called multiple - * times for a single device. Returns %0 in case of success, negative error in - * case of failure. When this function returns success, the device is - * deselected. - */ -static int ep93xx_spi_setup(struct spi_device *spi) +static void ep93xx_spi_cs_control(struct spi_device *spi, bool enable) { - struct ep93xx_spi *espi = spi_master_get_devdata(spi->master); - struct ep93xx_spi_chip *chip; + if (spi->mode & SPI_CS_HIGH) + enable = !enable; - chip = spi_get_ctldata(spi); - if (!chip) { - dev_dbg(&espi->pdev->dev, "initial setup for %s\n", - spi->modalias); - - chip = kzalloc(sizeof(*chip), GFP_KERNEL); - if (!chip) - return -ENOMEM; - - chip->spi = spi; - chip->ops = spi->controller_data; - - if (chip->ops && chip->ops->setup) { - int ret = chip->ops->setup(spi); - - if (ret) { - kfree(chip); - return ret; - } - } - - spi_set_ctldata(spi, chip); - } - - ep93xx_spi_cs_control(spi, false); - return 0; + if (gpio_is_valid(spi->cs_gpio)) + gpio_set_value(spi->cs_gpio, !enable); } -/** - * ep93xx_spi_cleanup() - cleans up master controller specific state - * @spi: SPI device to cleanup - * - * This function releases master controller specific state for given @spi - * device. - */ -static void ep93xx_spi_cleanup(struct spi_device *spi) -{ - struct ep93xx_spi_chip *chip; - - chip = spi_get_ctldata(spi); - if (chip) { - if (chip->ops && chip->ops->cleanup) - chip->ops->cleanup(spi); - spi_set_ctldata(spi, NULL); - kfree(chip); - } -} - -/** - * ep93xx_spi_chip_setup() - configures hardware according to given @chip - * @espi: ep93xx SPI controller struct - * @chip: chip specific settings - * @speed_hz: transfer speed - * @bits_per_word: transfer bits_per_word - */ static int ep93xx_spi_chip_setup(const struct ep93xx_spi *espi, - const struct ep93xx_spi_chip *chip, - u32 speed_hz, u8 bits_per_word) + struct spi_device *spi, + struct spi_transfer *xfer) { - u8 dss = bits_per_word_to_dss(bits_per_word); + u8 dss = bits_per_word_to_dss(xfer->bits_per_word); u8 div_cpsr = 0; u8 div_scr = 0; u16 cr0; int err; - err = ep93xx_spi_calc_divisors(espi, speed_hz, &div_cpsr, &div_scr); + err = ep93xx_spi_calc_divisors(espi, xfer->speed_hz, + &div_cpsr, &div_scr); if (err) return err; cr0 = div_scr << SSPCR0_SCR_SHIFT; - cr0 |= (chip->spi->mode & (SPI_CPHA|SPI_CPOL)) << SSPCR0_MODE_SHIFT; + cr0 |= (spi->mode & (SPI_CPHA | SPI_CPOL)) << SSPCR0_MODE_SHIFT; cr0 |= dss; dev_dbg(&espi->pdev->dev, "setup: mode %d, cpsr %d, scr %d, dss %d\n", - chip->spi->mode, div_cpsr, div_scr, dss); + spi->mode, div_cpsr, div_scr, dss); dev_dbg(&espi->pdev->dev, "setup: cr0 %#x\n", cr0); ep93xx_spi_write_u8(espi, SSPCPSR, div_cpsr); @@ -603,12 +526,11 @@ static void ep93xx_spi_process_transfer(struct ep93xx_spi *espi, struct spi_message *msg, struct spi_transfer *t) { - struct ep93xx_spi_chip *chip = spi_get_ctldata(msg->spi); int err; msg->state = t; - err = ep93xx_spi_chip_setup(espi, chip, t->speed_hz, t->bits_per_word); + err = ep93xx_spi_chip_setup(espi, msg->spi, t); if (err) { dev_err(&espi->pdev->dev, "failed to setup chip for transfer\n"); @@ -863,8 +785,13 @@ static int ep93xx_spi_probe(struct platform_device *pdev) struct resource *res; int irq; int error; + int i; info = dev_get_platdata(&pdev->dev); + if (!info) { + dev_err(&pdev->dev, "missing platform data\n"); + return -EINVAL; + } irq = platform_get_irq(pdev, 0); if (irq < 0) { @@ -882,14 +809,36 @@ static int ep93xx_spi_probe(struct platform_device *pdev) if (!master) return -ENOMEM; - master->setup = ep93xx_spi_setup; master->transfer_one_message = ep93xx_spi_transfer_one_message; - master->cleanup = ep93xx_spi_cleanup; master->bus_num = pdev->id; - master->num_chipselect = info->num_chipselect; master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16); + master->num_chipselect = info->num_chipselect; + master->cs_gpios = devm_kzalloc(&master->dev, + sizeof(int) * master->num_chipselect, + GFP_KERNEL); + if (!master->cs_gpios) { + error = -ENOMEM; + goto fail_release_master; + } + + for (i = 0; i < master->num_chipselect; i++) { + master->cs_gpios[i] = info->chipselect[i]; + + if (!gpio_is_valid(master->cs_gpios[i])) + continue; + + error = devm_gpio_request_one(&pdev->dev, master->cs_gpios[i], + GPIOF_OUT_INIT_HIGH, + "ep93xx-spi"); + if (error) { + dev_err(&pdev->dev, "could not request cs gpio %d\n", + master->cs_gpios[i]); + goto fail_release_master; + } + } + platform_set_drvdata(pdev, master); espi = spi_master_get_devdata(master); diff --git a/include/linux/platform_data/spi-ep93xx.h b/include/linux/platform_data/spi-ep93xx.h index 9bb63ac13f04..171a271c2cbd 100644 --- a/include/linux/platform_data/spi-ep93xx.h +++ b/include/linux/platform_data/spi-ep93xx.h @@ -5,25 +5,14 @@ struct spi_device; /** * struct ep93xx_spi_info - EP93xx specific SPI descriptor - * @num_chipselect: number of chip selects on this board, must be - * at least one + * @chipselect: array of gpio numbers to use as chip selects + * @num_chipselect: ARRAY_SIZE(chipselect) * @use_dma: use DMA for the transfers */ struct ep93xx_spi_info { + int *chipselect; int num_chipselect; bool use_dma; }; -/** - * struct ep93xx_spi_chip_ops - operation callbacks for SPI slave device - * @setup: setup the chip select mechanism - * @cleanup: cleanup the chip select mechanism - * @cs_control: control the device chip select - */ -struct ep93xx_spi_chip_ops { - int (*setup)(struct spi_device *spi); - void (*cleanup)(struct spi_device *spi); - void (*cs_control)(struct spi_device *spi, int value); -}; - #endif /* __ASM_MACH_EP93XX_SPI_H */ |