diff options
121 files changed, 6467 insertions, 2194 deletions
diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt index 0ee8edb60efc..f33da8782741 100644 --- a/Documentation/devicetree/bindings/mtd/denali-nand.txt +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt @@ -8,6 +8,9 @@ Required properties: - reg : should contain registers location and length for data and reg. - reg-names: Should contain the reg names "nand_data" and "denali_reg" - interrupts : The interrupt number. + - clocks: should contain phandle of the controller core clock, the bus + interface clock, and the ECC circuit clock. + - clock-names: should contain "nand", "nand_x", "ecc" Optional properties: - nand-ecc-step-size: see nand.txt for details. If present, the value must be @@ -31,5 +34,7 @@ nand: nand@ff900000 { compatible = "altr,socfpga-denali-nand"; reg = <0xff900000 0x20>, <0xffb80000 0x1000>; reg-names = "nand_data", "denali_reg"; + clocks = <&nand_clk>, <&nand_x_clk>, <&nand_ecc_clk>; + clock-names = "nand", "nand_x", "ecc"; interrupts = <0 144 4>; }; diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index 956bb046e599..f03be904d3c2 100644 --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -69,6 +69,15 @@ Optional properties: all chips and support for it can not be detected at runtime. Refer to your chips' datasheet to check if this is supported by your chip. +- broken-flash-reset : Some flash devices utilize stateful addressing modes + (e.g., for 32-bit addressing) which need to be managed + carefully by a system. Because these sorts of flash don't + have a standardized software reset command, and because some + systems don't toggle the flash RESET# pin upon system reset + (if the pin even exists at all), there are systems which + cannot reboot properly if the flash is left in the "wrong" + state. This boolean flag can be used on such systems, to + denote the absence of a reliable reset mechanism. Example: diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt index 8bb11d809429..e949c778e983 100644 --- a/Documentation/devicetree/bindings/mtd/nand.txt +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -25,7 +25,7 @@ Optional NAND chip properties: Deprecated values: "soft_bch": use "soft" and nand-ecc-algo instead - nand-ecc-algo: string, algorithm of NAND ECC. - Supported values are: "hamming", "bch". + Valid values are: "hamming", "bch", "rs". - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false @@ -43,6 +43,10 @@ Optional NAND chip properties: This is particularly useful when only the in-band area is used by the upper layers, and you want to make your NAND as reliable as possible. +- nand-is-boot-medium: Whether the NAND chip is a boot medium. Drivers might use + this information to select ECC algorithms supported by + the boot ROM or similar restrictions. + - nand-rb: shall contain the native Ready/Busy ids. The ECC strength and ECC step size properties define the correction capability diff --git a/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt new file mode 100644 index 000000000000..b2f2ca12f9e6 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt @@ -0,0 +1,64 @@ +NVIDIA Tegra NAND Flash controller + +Required properties: +- compatible: Must be one of: + - "nvidia,tegra20-nand" +- reg: MMIO address range +- interrupts: interrupt output of the NFC controller +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - nand +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - nand + +Optional children nodes: +Individual NAND chips are children of the NAND controller node. Currently +only one NAND chip supported. + +Required children node properties: +- reg: An integer ranging from 1 to 6 representing the CS line to use. + +Optional children node properties: +- nand-ecc-mode: String, operation mode of the NAND ecc mode. Currently only + "hw" is supported. +- nand-ecc-algo: string, algorithm of NAND ECC. + Supported values with "hw" ECC mode are: "rs", "bch". +- nand-bus-width : See nand.txt +- nand-on-flash-bbt: See nand.txt +- nand-ecc-strength: integer representing the number of bits to correct + per ECC step (always 512). Supported strength using HW ECC + modes are: + - RS: 4, 6, 8 + - BCH: 4, 8, 14, 16 +- nand-ecc-maximize: See nand.txt +- nand-is-boot-medium: Makes sure only ECC strengths supported by the boot ROM + are chosen. +- wp-gpios: GPIO specifier for the write protect pin. + +Optional child node of NAND chip nodes: +Partitions: see partition.txt + + Example: + nand-controller@70008000 { + compatible = "nvidia,tegra20-nand"; + reg = <0x70008000 0x100>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA20_CLK_NDFLASH>; + clock-names = "nand"; + resets = <&tegra_car 13>; + reset-names = "nand"; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-bus-width = <8>; + nand-on-flash-bbt; + nand-ecc-algo = "bch"; + nand-ecc-strength = <8>; + wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index a8f382642ba9..afbbd870496d 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -14,6 +14,13 @@ method is used for a given flash device. To describe the method there should be a subnode of the flash device that is named 'partitions'. It must have a 'compatible' property, which is used to identify the method to use. +When a single partition is represented with a DT node (it depends on a used +format) it may also be described using above rules ('compatible' and optionally +some extra properties / subnodes). It allows describing more complex, +hierarchical (multi-level) layouts and should be used if there is some +significant relation between partitions or some partition internally uses +another partitioning method. + Available bindings are listed in the "partitions" subdirectory. @@ -109,3 +116,42 @@ flash@2 { }; }; }; + +flash@3 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x000000 0x100000>; + read-only; + }; + + firmware@100000 { + label = "firmware"; + reg = <0x100000 0xe00000>; + compatible = "brcm,trx"; + }; + + calibration@f00000 { + label = "calibration"; + reg = <0xf00000 0x100000>; + compatible = "fixed-partitions"; + ranges = <0 0xf00000 0x100000>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "wifi0"; + reg = <0x000000 0x080000>; + }; + + partition@80000 { + label = "wifi1"; + reg = <0x080000 0x080000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt b/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt new file mode 100644 index 000000000000..b677147ca4e1 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/partitions/brcm,trx.txt @@ -0,0 +1,37 @@ +Broadcom TRX Container Partition +================================ + +TRX is Broadcom's official firmware format for the BCM947xx boards. It's used by +most of the vendors building devices based on Broadcom's BCM47xx SoCs and is +supported by the CFE bootloader. + +Design of the TRX format is very minimalistic. Its header contains +identification fields, CRC32 checksum and the locations of embedded partitions. +Its purpose is to store a few partitions in a format that can be distributed as +a standalone file and written in a flash memory. + +Container can hold up to 4 partitions. The first partition has to contain a +device executable binary (e.g. a kernel) as it's what the CFE bootloader starts +executing. Other partitions can be used for operating system purposes. This is +useful for systems that keep kernel and rootfs separated. + +TRX doesn't enforce any strict partition boundaries or size limits. All +partitions have to be less than the 4GiB max size limit. + +There are two existing/known TRX variants: +1) v1 which contains 3 partitions +2) v2 which contains 4 partitions + +There aren't separated compatible bindings for them as version can be trivialy +detected by a software parsing TRX header. + +Required properties: +- compatible : (required) must be "brcm,trx" + +Example: + +flash@0 { + partitions { + compatible = "brcm,trx"; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt index 73d336befa08..1123cc6d56ef 100644 --- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt +++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt @@ -45,11 +45,12 @@ Required properties: number (e.g., 0, 1, 2, etc.) - #address-cells: see partition.txt - #size-cells: see partition.txt -- nand-ecc-strength: see nand.txt -- nand-ecc-step-size: must be 512. see nand.txt for more details. Optional properties: - nand-bus-width: see nand.txt +- nand-ecc-strength: see nand.txt. If not specified, then ECC strength will + be used according to chip requirement and available + OOB size. Each nandcs device node may optionally contain a 'partitions' sub-node, which further contains sub-nodes describing the flash partition mapping. See @@ -77,7 +78,6 @@ nand-controller@1ac00000 { reg = <0>; nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; nand-bus-width = <8>; partitions { @@ -117,7 +117,6 @@ nand-controller@79b0000 { nand@0 { reg = <0>; nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; nand-bus-width = <8>; partitions { diff --git a/Documentation/devicetree/bindings/mtd/spi-nand.txt b/Documentation/devicetree/bindings/mtd/spi-nand.txt new file mode 100644 index 000000000000..8b51f3b6d55c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/spi-nand.txt @@ -0,0 +1,5 @@ +SPI NAND flash + +Required properties: +- compatible: should be "spi-nand" +- reg: should encode the chip-select line used to access the NAND chip diff --git a/MAINTAINERS b/MAINTAINERS index 0a2342770dee..78608226c30a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -9353,7 +9353,6 @@ F: drivers/media/platform/atmel/atmel-isc-regs.h F: devicetree/bindings/media/atmel-isc.txt MICROCHIP / ATMEL NAND DRIVER -M: Wenyou Yang <wenyou.yang@microchip.com> M: Josh Wu <rainyfeeling@outlook.com> L: linux-mtd@lists.infradead.org S: Supported @@ -14063,6 +14062,13 @@ M: Laxman Dewangan <ldewangan@nvidia.com> S: Supported F: drivers/input/keyboard/tegra-kbc.c +TEGRA NAND DRIVER +M: Stefan Agner <stefan@agner.ch> +M: Lucas Stach <dev@lynxeye.de> +S: Maintained +F: Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt +F: drivers/mtd/nand/raw/tegra_nand.c + TEGRA PWM DRIVER M: Thierry Reding <thierry.reding@gmail.com> S: Supported diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c index f4f8f23bda8c..af46d2182533 100644 --- a/arch/arm/mach-pxa/balloon3.c +++ b/arch/arm/mach-pxa/balloon3.c @@ -688,7 +688,6 @@ struct platform_nand_data balloon3_nand_pdata = { .chip_delay = 50, }, .ctrl = { - .hwcontrol = 0, .dev_ready = balloon3_nand_dev_ready, .select_chip = balloon3_nand_select_chip, .cmd_ctrl = balloon3_nand_cmd_ctl, diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index 49022ad338e9..29be04c6cc48 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -346,7 +346,6 @@ struct platform_nand_data em_x270_nand_platdata = { .chip_delay = 20, }, .ctrl = { - .hwcontrol = 0, .dev_ready = em_x270_nand_device_ready, .select_chip = 0, .cmd_ctrl = em_x270_nand_cmd_ctl, diff --git a/arch/ia64/include/asm/io.h b/arch/ia64/include/asm/io.h index fb0651961e2c..6f952171abf9 100644 --- a/arch/ia64/include/asm/io.h +++ b/arch/ia64/include/asm/io.h @@ -83,12 +83,14 @@ virt_to_phys (volatile void *address) { return (unsigned long) address - PAGE_OFFSET; } +#define virt_to_phys virt_to_phys static inline void* phys_to_virt (unsigned long address) { return (void *) (address + PAGE_OFFSET); } +#define phys_to_virt phys_to_virt #define ARCH_HAS_VALID_PHYS_ADDR_RANGE extern u64 kern_mem_attribute (unsigned long phys_addr, unsigned long size); @@ -433,9 +435,11 @@ static inline void __iomem * ioremap_cache (unsigned long phys_addr, unsigned lo { return ioremap(phys_addr, size); } +#define ioremap ioremap +#define ioremap_nocache ioremap_nocache #define ioremap_cache ioremap_cache #define ioremap_uc ioremap_nocache - +#define iounmap iounmap /* * String version of IO memory access ops: @@ -444,6 +448,13 @@ extern void memcpy_fromio(void *dst, const volatile void __iomem *src, long n); extern void memcpy_toio(volatile void __iomem *dst, const void *src, long n); extern void memset_io(volatile void __iomem *s, int c, long n); +#define memcpy_fromio memcpy_fromio +#define memcpy_toio memcpy_toio +#define memset_io memset_io +#define xlate_dev_kmem_ptr xlate_dev_kmem_ptr +#define xlate_dev_mem_ptr xlate_dev_mem_ptr +#include <asm-generic/io.h> + # endif /* __KERNEL__ */ #endif /* _ASM_IA64_IO_H */ diff --git a/arch/mips/jz4740/board-qi_lb60.c b/arch/mips/jz4740/board-qi_lb60.c index 60f0767507c6..af0c8ace0141 100644 --- a/arch/mips/jz4740/board-qi_lb60.c +++ b/arch/mips/jz4740/board-qi_lb60.c @@ -29,10 +29,11 @@ #include <linux/power/gpio-charger.h> #include <linux/pwm.h> +#include <linux/platform_data/jz4740/jz4740_nand.h> + #include <asm/mach-jz4740/gpio.h> #include <asm/mach-jz4740/jz4740_fb.h> #include <asm/mach-jz4740/jz4740_mmc.h> -#include <asm/mach-jz4740/jz4740_nand.h> #include <linux/regulator/fixed.h> #include <linux/regulator/machine.h> diff --git a/arch/mips/txx9/generic/setup.c b/arch/mips/txx9/generic/setup.c index dde4dc859f79..f6d9182ef82a 100644 --- a/arch/mips/txx9/generic/setup.c +++ b/arch/mips/txx9/generic/setup.c @@ -20,6 +20,7 @@ #include <linux/err.h> #include <linux/gpio/driver.h> #include <linux/platform_device.h> +#include <linux/platform_data/txx9/ndfmc.h> #include <linux/serial_core.h> #include <linux/mtd/physmap.h> #include <linux/leds.h> @@ -36,7 +37,6 @@ #include <asm/txx9/generic.h> #include <asm/txx9/pci.h> #include <asm/txx9tmr.h> -#include <asm/txx9/ndfmc.h> #include <asm/txx9/dmac.h> #ifdef CONFIG_CPU_TX49XX #include <asm/txx9/tx4938.h> diff --git a/arch/mips/txx9/generic/setup_tx4938.c b/arch/mips/txx9/generic/setup_tx4938.c index 85d1795652da..17395d5d15ca 100644 --- a/arch/mips/txx9/generic/setup_tx4938.c +++ b/arch/mips/txx9/generic/setup_tx4938.c @@ -17,13 +17,13 @@ #include <linux/ptrace.h> #include <linux/mtd/physmap.h> #include <linux/platform_device.h> +#include <linux/platform_data/txx9/ndfmc.h> #include <asm/reboot.h> #include <asm/traps.h> #include <asm/txx9irq.h> #include <asm/txx9tmr.h> #include <asm/txx9pio.h> #include <asm/txx9/generic.h> -#include <asm/txx9/ndfmc.h> #include <asm/txx9/dmac.h> #include <asm/txx9/tx4938.h> diff --git a/arch/mips/txx9/generic/setup_tx4939.c b/arch/mips/txx9/generic/setup_tx4939.c index 274928987a21..360c388f4c82 100644 --- a/arch/mips/txx9/generic/setup_tx4939.c +++ b/arch/mips/txx9/generic/setup_tx4939.c @@ -21,13 +21,13 @@ #include <linux/ptrace.h> #include <linux/mtd/physmap.h> #include <linux/platform_device.h> +#include <linux/platform_data/txx9/ndfmc.h> #include <asm/bootinfo.h> #include <asm/reboot.h> #include <asm/traps.h> #include <asm/txx9irq.h> #include <asm/txx9tmr.h> #include <asm/txx9/generic.h> -#include <asm/txx9/ndfmc.h> #include <asm/txx9/dmac.h> #include <asm/txx9/tx4939.h> diff --git a/arch/sparc/include/asm/io_64.h b/arch/sparc/include/asm/io_64.h index 9a1e9cbc7e6d..b162c23ae8c2 100644 --- a/arch/sparc/include/asm/io_64.h +++ b/arch/sparc/include/asm/io_64.h @@ -243,35 +243,42 @@ void insb(unsigned long, void *, unsigned long); void insw(unsigned long, void *, unsigned long); void insl(unsigned long, void *, unsigned long); -static inline void ioread8_rep(void __iomem *port, void *buf, unsigned long count) +static inline void readsb(void __iomem *port, void *buf, unsigned long count) { insb((unsigned long __force)port, buf, count); } -static inline void ioread16_rep(void __iomem *port, void *buf, unsigned long count) +static inline void readsw(void __iomem *port, void *buf, unsigned long count) { insw((unsigned long __force)port, buf, count); } -static inline void ioread32_rep(void __iomem *port, void *buf, unsigned long count) +static inline void readsl(void __iomem *port, void *buf, unsigned long count) { insl((unsigned long __force)port, buf, count); } -static inline void iowrite8_rep(void __iomem *port, const void *buf, unsigned long count) +static inline void writesb(void __iomem *port, const void *buf, unsigned long count) { outsb((unsigned long __force)port, buf, count); } -static inline void iowrite16_rep(void __iomem *port, const void *buf, unsigned long count) +static inline void writesw(void __iomem *port, const void *buf, unsigned long count) { outsw((unsigned long __force)port, buf, count); } -static inline void iowrite32_rep(void __iomem *port, const void *buf, unsigned long count) +static inline void writesl(void __iomem *port, const void *buf, unsigned long count) { outsl((unsigned long __force)port, buf, count); } +#define ioread8_rep(p,d,l) readsb(p,d,l) +#define ioread16_rep(p,d,l) readsw(p,d,l) +#define ioread32_rep(p,d,l) readsl(p,d,l) +#define iowrite8_rep(p,d,l) writesb(p,d,l) +#define iowrite16_rep(p,d,l) writesw(p,d,l) +#define iowrite32_rep(p,d,l) writesl(p,d,l) + /* Valid I/O Space regions are anywhere, because each PCI bus supported * can live in an arbitrary area of the physical address range. */ diff --git a/drivers/bcma/Kconfig b/drivers/bcma/Kconfig index cb0f1aad20b7..b9558ff20830 100644 --- a/drivers/bcma/Kconfig +++ b/drivers/bcma/Kconfig @@ -30,6 +30,7 @@ config BCMA_HOST_PCI config BCMA_HOST_SOC bool "Support for BCMA in a SoC" + depends on HAS_IOMEM help Host interface for a Broadcom AIX bus directly mapped into the memory. This only works with the Broadcom SoCs from the @@ -61,7 +62,7 @@ config BCMA_DRIVER_PCI_HOSTMODE config BCMA_DRIVER_MIPS bool "BCMA Broadcom MIPS core driver" - depends on MIPS + depends on MIPS || COMPILE_TEST help Driver for the Broadcom MIPS core attached to Broadcom specific Advanced Microcontroller Bus. diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig index 8d731d6c3e54..63389f075f1d 100644 --- a/drivers/memory/Kconfig +++ b/drivers/memory/Kconfig @@ -116,12 +116,14 @@ config FSL_CORENET_CF config FSL_IFC bool - depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A + depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A || COMPILE_TEST + depends on HAS_IOMEM config JZ4780_NEMC bool "Ingenic JZ4780 SoC NEMC driver" default y - depends on MACH_JZ4780 + depends on MACH_JZ4780 || COMPILE_TEST + depends on HAS_IOMEM && OF help This driver is for the NAND/External Memory Controller (NEMC) in the Ingenic JZ4780. This controller is used to handle external diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig index 46ab7feec6b6..c77f537323ec 100644 --- a/drivers/mtd/Kconfig +++ b/drivers/mtd/Kconfig @@ -24,7 +24,7 @@ config MTD_TESTS config MTD_REDBOOT_PARTS tristate "RedBoot partition table parsing" - ---help--- + help RedBoot is a ROM monitor and bootloader which deals with multiple 'images' in flash devices by putting a table one of the erase blocks on the device, similar to a partition table, which gives @@ -45,7 +45,7 @@ if MTD_REDBOOT_PARTS config MTD_REDBOOT_DIRECTORY_BLOCK int "Location of RedBoot partition table" default "-1" - ---help--- + help This option is the Linux counterpart to the CYGNUM_REDBOOT_FIS_DIRECTORY_BLOCK RedBoot compile time option. @@ -75,7 +75,7 @@ endif # MTD_REDBOOT_PARTS config MTD_CMDLINE_PARTS tristate "Command line partition table parsing" depends on MTD - ---help--- + help Allow generic configuration of the MTD partition tables via the kernel command line. Multiple flash resources are supported for hardware where different kinds of flash memory are available. @@ -112,7 +112,7 @@ config MTD_CMDLINE_PARTS config MTD_AFS_PARTS tristate "ARM Firmware Suite partition parsing" depends on (ARM || ARM64) - ---help--- + help The ARM Firmware Suite allows the user to divide flash devices into multiple 'images'. Each such image has a header containing its name and offset/size etc. @@ -136,7 +136,7 @@ config MTD_OF_PARTS config MTD_AR7_PARTS tristate "TI AR7 partitioning support" - ---help--- + help TI AR7 partitioning support config MTD_BCM63XX_PARTS @@ -170,7 +170,7 @@ config MTD_BLOCK tristate "Caching block device access to MTD devices" depends on BLOCK select MTD_BLKDEVS - ---help--- + help Although most flash chips have an erase size too large to be useful as block devices, it is possible to use MTD devices which are based on RAM chips in this manner. This block device is a user of MTD @@ -205,7 +205,7 @@ config FTL tristate "FTL (Flash Translation Layer) support" depends on BLOCK select MTD_BLKDEVS - ---help--- + help This provides support for the original Flash Translation Layer which is part of the PCMCIA specification. It uses a kind of pseudo- file system on a flash device to emulate a block device with @@ -222,7 +222,7 @@ config NFTL tristate "NFTL (NAND Flash Translation Layer) support" depends on BLOCK select MTD_BLKDEVS - ---help--- + help This provides support for the NAND Flash Translation Layer which is used on M-Systems' DiskOnChip devices. It uses a kind of pseudo- file system on a flash device to emulate a block device with @@ -246,7 +246,7 @@ config INFTL tristate "INFTL (Inverse NAND Flash Translation Layer) support" depends on BLOCK select MTD_BLKDEVS - ---help--- + help This provides support for the Inverse NAND Flash Translation Layer which is used on M-Systems' newer DiskOnChip devices. It uses a kind of pseudo-file system on a flash device to emulate @@ -261,10 +261,10 @@ config INFTL not use it. config RFD_FTL - tristate "Resident Flash Disk (Flash Translation Layer) support" + tristate "Resident Flash Disk (Flash Translation Layer) support" depends on BLOCK select MTD_BLKDEVS - ---help--- + help This provides support for the flash translation layer known as the Resident Flash Disk (RFD), as used by the Embedded BIOS of General Software. There is a blurb at: @@ -308,7 +308,7 @@ config MTD_SWAP select MTD_BLKDEVS help Provides volatile block device driver on top of mtd partition - suitable for swapping. The mapping of written blocks is not saved. + suitable for swapping. The mapping of written blocks is not saved. The driver provides wear leveling by storing erase counter into the OOB. diff --git a/drivers/mtd/chips/Kconfig b/drivers/mtd/chips/Kconfig index bbfa1f129266..39ec32a29051 100644 --- a/drivers/mtd/chips/Kconfig +++ b/drivers/mtd/chips/Kconfig @@ -44,7 +44,7 @@ choice prompt "Flash cmd/query data swapping" depends on MTD_CFI_ADV_OPTIONS default MTD_CFI_NOSWAP - ---help--- + help This option defines the way in which the CPU attempts to arrange data bits when writing the 'magic' commands to the chips. Saying 'NO', which is the default when CONFIG_MTD_CFI_ADV_OPTIONS isn't diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c index 1b64ac8c5bc8..72428b6bfc47 100644 --- a/drivers/mtd/chips/cfi_cmdset_0002.c +++ b/drivers/mtd/chips/cfi_cmdset_0002.c @@ -1216,7 +1216,6 @@ static inline int do_read_secsi_onechip(struct map_info *map, size_t grouplen) { DECLARE_WAITQUEUE(wait, current); - unsigned long timeo = jiffies + HZ; retry: mutex_lock(&chip->mutex); @@ -1229,7 +1228,6 @@ static inline int do_read_secsi_onechip(struct map_info *map, schedule(); remove_wait_queue(&chip->wq, &wait); - timeo = jiffies + HZ; goto retry; } diff --git a/drivers/mtd/chips/gen_probe.c b/drivers/mtd/chips/gen_probe.c index b57ceea21513..837b04ab96a9 100644 --- a/drivers/mtd/chips/gen_probe.c +++ b/drivers/mtd/chips/gen_probe.c @@ -202,16 +202,19 @@ static inline struct mtd_info *cfi_cmdset_unknown(struct map_info *map, struct cfi_private *cfi = map->fldrv_priv; __u16 type = primary?cfi->cfiq->P_ID:cfi->cfiq->A_ID; #ifdef CONFIG_MODULES - char probename[sizeof(VMLINUX_SYMBOL_STR(cfi_cmdset_%4.4X))]; cfi_cmdset_fn_t *probe_function; + char *probename; - sprintf(probename, VMLINUX_SYMBOL_STR(cfi_cmdset_%4.4X), type); + probename = kasprintf(GFP_KERNEL, "cfi_cmdset_%4.4X", type); + if (!probename) + return NULL; probe_function = __symbol_get(probename); if (!probe_function) { request_module("cfi_cmdset_%4.4X", type); probe_function = __symbol_get(probename); } + kfree(probename); if (probe_function) { struct mtd_info *mtd; diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig index 57b02c4b3f63..e514d57a0419 100644 --- a/drivers/mtd/devices/Kconfig +++ b/drivers/mtd/devices/Kconfig @@ -5,7 +5,7 @@ menu "Self-contained MTD device drivers" config MTD_PMC551 tristate "Ramix PMC551 PCI Mezzanine RAM card support" depends on PCI - ---help--- + help This provides a MTD device driver for the Ramix PMC551 RAM PCI card from Ramix Inc. <http://www.ramix.com/products/memory/pmc551.html>. These devices come in memory configurations from 32M - 1G. If you @@ -209,7 +209,7 @@ config MTD_DOCG3 select BCH select BCH_CONST_PARAMS select BITREVERSE - ---help--- + help This provides an MTD device driver for the M-Systems DiskOnChip G3 devices. diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c index e84563d2067f..fe260ccb2d7d 100644 --- a/drivers/mtd/devices/m25p80.c +++ b/drivers/mtd/devices/m25p80.c @@ -28,11 +28,9 @@ #include <linux/spi/flash.h> #include <linux/mtd/spi-nor.h> -#define MAX_CMD_SIZE 6 struct m25p { struct spi_mem *spimem; struct spi_nor spi_nor; - u8 command[MAX_CMD_SIZE]; }; static int m25p80_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len) @@ -70,7 +68,7 @@ static ssize_t m25p80_write(struct spi_nor *nor, loff_t to, size_t len, struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 1), SPI_MEM_OP_ADDR(nor->addr_width, to, 1), - SPI_MEM_OP_DUMMY(0, 1), + SPI_MEM_OP_NO_DUMMY, SPI_MEM_OP_DATA_OUT(len, buf, 1)); size_t remaining = len; int ret; @@ -78,7 +76,6 @@ static ssize_t m25p80_write(struct spi_nor *nor, loff_t to, size_t len, /* get transfer protocols. */ op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->write_proto); op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->write_proto); - op.dummy.buswidth = op.addr.buswidth; op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto); if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second) diff --git a/drivers/mtd/devices/powernv_flash.c b/drivers/mtd/devices/powernv_flash.c index c1312b141ae0..33593122e49b 100644 --- a/drivers/mtd/devices/powernv_flash.c +++ b/drivers/mtd/devices/powernv_flash.c @@ -223,6 +223,7 @@ static int powernv_flash_set_driver_info(struct device *dev, mtd->_read = powernv_flash_read; mtd->_write = powernv_flash_write; mtd->dev.parent = dev; + mtd_set_of_node(mtd, dev->of_node); return 0; } diff --git a/drivers/mtd/devices/sst25l.c b/drivers/mtd/devices/sst25l.c index 1897f33fe3e7..10d24efb4629 100644 --- a/drivers/mtd/devices/sst25l.c +++ b/drivers/mtd/devices/sst25l.c @@ -394,9 +394,8 @@ static int sst25l_probe(struct spi_device *spi) flash->mtd.numeraseregions); - ret = mtd_device_parse_register(&flash->mtd, NULL, NULL, - data ? data->parts : NULL, - data ? data->nr_parts : 0); + ret = mtd_device_register(&flash->mtd, data ? data->parts : NULL, + data ? data->nr_parts : 0); if (ret) return -ENODEV; diff --git a/drivers/mtd/lpddr/Kconfig b/drivers/mtd/lpddr/Kconfig index 3a19cbee24d7..a5a332fbd593 100644 --- a/drivers/mtd/lpddr/Kconfig +++ b/drivers/mtd/lpddr/Kconfig @@ -13,10 +13,10 @@ config MTD_QINFO_PROBE depends on MTD_LPDDR tristate "Detect flash chips by QINFO probe" help - Device Information for LPDDR chips is offered through the Overlay - Window QINFO interface, permits software to be used for entire - families of devices. This serves similar purpose of CFI on legacy - Flash products + Device Information for LPDDR chips is offered through the Overlay + Window QINFO interface, permits software to be used for entire + families of devices. This serves similar purpose of CFI on legacy + Flash products config MTD_LPDDR2_NVM # ARM dependency is only for writel_relaxed() diff --git a/drivers/mtd/lpddr/lpddr2_nvm.c b/drivers/mtd/lpddr/lpddr2_nvm.c index 5d73db2a496d..c950c880ad59 100644 --- a/drivers/mtd/lpddr/lpddr2_nvm.c +++ b/drivers/mtd/lpddr/lpddr2_nvm.c @@ -476,7 +476,7 @@ static int lpddr2_nvm_probe(struct platform_device *pdev) return -EINVAL; } /* Parse partitions and register the MTD device */ - return mtd_device_parse_register(mtd, NULL, NULL, NULL, 0); + return mtd_device_register(mtd, NULL, 0); } /* diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig index bdc1283f30fb..afb36bff13a7 100644 --- a/drivers/mtd/maps/Kconfig +++ b/drivers/mtd/maps/Kconfig @@ -207,13 +207,13 @@ config MTD_ICHXROM BE VERY CAREFUL. config MTD_ESB2ROM - tristate "BIOS flash chip on Intel ESB Controller Hub 2" - depends on X86 && MTD_JEDECPROBE && PCI - help - Support for treating the BIOS flash chip on ESB2 motherboards - as an MTD device - with this you can reprogram your BIOS. + tristate "BIOS flash chip on Intel ESB Controller Hub 2" + depends on X86 && MTD_JEDECPROBE && PCI + help + Support for treating the BIOS flash chip on ESB2 motherboards + as an MTD device - with this you can reprogram your BIOS. - BE VERY CAREFUL. + BE VERY CAREFUL. config MTD_CK804XROM tristate "BIOS flash chip on Nvidia CK804" @@ -401,12 +401,12 @@ config MTD_PISMO When built as a module, it will be called pismo.ko config MTD_LATCH_ADDR - tristate "Latch-assisted Flash Chip Support" - depends on MTD_COMPLEX_MAPPINGS - help - Map driver which allows flashes to be partially physically addressed - and have the upper address lines set by a board specific code. + tristate "Latch-assisted Flash Chip Support" + depends on MTD_COMPLEX_MAPPINGS + help + Map driver which allows flashes to be partially physically addressed + and have the upper address lines set by a board specific code. - If compiled as a module, it will be called latch-addr-flash. + If compiled as a module, it will be called latch-addr-flash. endmenu diff --git a/drivers/mtd/maps/gpio-addr-flash.c b/drivers/mtd/maps/gpio-addr-flash.c index 385305e66fd1..9d9723693217 100644 --- a/drivers/mtd/maps/gpio-addr-flash.c +++ b/drivers/mtd/maps/gpio-addr-flash.c @@ -239,6 +239,9 @@ static int gpio_flash_probe(struct platform_device *pdev) state->map.bankwidth = pdata->width; state->map.size = state->win_size * (1 << state->gpio_count); state->map.virt = ioremap_nocache(memory->start, state->map.size); + if (!state->map.virt) + return -ENOMEM; + state->map.phys = NO_XIP; state->map.map_priv_1 = (unsigned long)state; diff --git a/drivers/mtd/maps/impa7.c b/drivers/mtd/maps/impa7.c index a0b8fa7849a9..815e2db87955 100644 --- a/drivers/mtd/maps/impa7.c +++ b/drivers/mtd/maps/impa7.c @@ -88,9 +88,8 @@ static int __init init_impa7(void) if (impa7_mtd[i]) { impa7_mtd[i]->owner = THIS_MODULE; devicesfound++; - mtd_device_parse_register(impa7_mtd[i], NULL, NULL, - partitions, - ARRAY_SIZE(partitions)); + mtd_device_register(impa7_mtd[i], partitions, + ARRAY_SIZE(partitions)); } else { iounmap((void __iomem *)impa7_map[i].virt); } diff --git a/drivers/mtd/maps/intel_vr_nor.c b/drivers/mtd/maps/intel_vr_nor.c index dd5d6855f543..69503aef981e 100644 --- a/drivers/mtd/maps/intel_vr_nor.c +++ b/drivers/mtd/maps/intel_vr_nor.c @@ -71,7 +71,7 @@ static int vr_nor_init_partitions(struct vr_nor_mtd *p) { /* register the flash bank */ /* partition the flash bank */ - return mtd_device_parse_register(p->info, NULL, NULL, NULL, 0); + return mtd_device_register(p->info, NULL, 0); } static void vr_nor_destroy_mtd_setup(struct vr_nor_mtd *p) diff --git a/drivers/mtd/maps/latch-addr-flash.c b/drivers/mtd/maps/latch-addr-flash.c index 6dc97aa667dc..51db24b7f88d 100644 --- a/drivers/mtd/maps/latch-addr-flash.c +++ b/drivers/mtd/maps/latch-addr-flash.c @@ -197,9 +197,8 @@ static int latch_addr_flash_probe(struct platform_device *dev) } info->mtd->dev.parent = &dev->dev; - mtd_device_parse_register(info->mtd, NULL, NULL, - latch_addr_data->parts, - latch_addr_data->nr_parts); + mtd_device_register(info->mtd, latch_addr_data->parts, + latch_addr_data->nr_parts); return 0; iounmap: diff --git a/drivers/mtd/maps/rbtx4939-flash.c b/drivers/mtd/maps/rbtx4939-flash.c index 3a06ecfc55ff..80a187167c92 100644 --- a/drivers/mtd/maps/rbtx4939-flash.c +++ b/drivers/mtd/maps/rbtx4939-flash.c @@ -97,8 +97,7 @@ static int rbtx4939_flash_probe(struct platform_device *dev) goto err_out; } info->mtd->dev.parent = &dev->dev; - err = mtd_device_parse_register(info->mtd, NULL, NULL, pdata->parts, - pdata->nr_parts); + err = mtd_device_register(info->mtd, pdata->parts, pdata->nr_parts); if (err) goto err_out; diff --git a/drivers/mtd/maps/solutionengine.c b/drivers/mtd/maps/solutionengine.c index bb580bc16445..c07f21b20463 100644 --- a/drivers/mtd/maps/solutionengine.c +++ b/drivers/mtd/maps/solutionengine.c @@ -59,9 +59,9 @@ static int __init init_soleng_maps(void) return -ENXIO; } } - printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n", - soleng_flash_map.phys & 0x1fffffff, - soleng_eprom_map.phys & 0x1fffffff); + printk(KERN_NOTICE "Solution Engine: Flash at 0x%pap, EPROM at 0x%pap\n", + &soleng_flash_map.phys, + &soleng_eprom_map.phys); flash_mtd->owner = THIS_MODULE; eprom_mtd = do_map_probe("map_rom", &soleng_eprom_map); diff --git a/drivers/mtd/mtdchar.c b/drivers/mtd/mtdchar.c index cd67c85cc87d..02389528f622 100644 --- a/drivers/mtd/mtdchar.c +++ b/drivers/mtd/mtdchar.c @@ -160,8 +160,12 @@ static ssize_t mtdchar_read(struct file *file, char __user *buf, size_t count, pr_debug("MTD_read\n"); - if (*ppos + count > mtd->size) - count = mtd->size - *ppos; + if (*ppos + count > mtd->size) { + if (*ppos < mtd->size) + count = mtd->size - *ppos; + else + count = 0; + } if (!count) return 0; @@ -246,7 +250,7 @@ static ssize_t mtdchar_write(struct file *file, const char __user *buf, size_t c pr_debug("MTD_write\n"); - if (*ppos == mtd->size) + if (*ppos >= mtd->size) return -ENOSPC; if (*ppos + count > mtd->size) diff --git a/drivers/mtd/mtdcore.c b/drivers/mtd/mtdcore.c index 42395df06be9..97ac219c082e 100644 --- a/drivers/mtd/mtdcore.c +++ b/drivers/mtd/mtdcore.c @@ -1155,21 +1155,29 @@ int mtd_read_oob(struct mtd_info *mtd, loff_t from, struct mtd_oob_ops *ops) { int ret_code; ops->retlen = ops->oobretlen = 0; - if (!mtd->_read_oob) - return -EOPNOTSUPP; ret_code = mtd_check_oob_ops(mtd, from, ops); if (ret_code) return ret_code; ledtrig_mtd_activity(); + + /* Check the validity of a potential fallback on mtd->_read */ + if (!mtd->_read_oob && (!mtd->_read || ops->oobbuf)) + return -EOPNOTSUPP; + + if (mtd->_read_oob) + ret_code = mtd->_read_oob(mtd, from, ops); + else + ret_code = mtd->_read(mtd, from, ops->len, &ops->retlen, + ops->datbuf); + /* * In cases where ops->datbuf != NULL, mtd->_read_oob() has semantics * similar to mtd->_read(), returning a non-negative integer * representing max bitflips. In other cases, mtd->_read_oob() may * return -EUCLEAN. In all cases, perform similar logic to mtd_read(). */ - ret_code = mtd->_read_oob(mtd, from, ops); if (unlikely(ret_code < 0)) return ret_code; if (mtd->ecc_strength == 0) @@ -1184,8 +1192,7 @@ int mtd_write_oob(struct mtd_info *mtd, loff_t to, int ret; ops->retlen = ops->oobretlen = 0; - if (!mtd->_write_oob) - return -EOPNOTSUPP; + if (!(mtd->flags & MTD_WRITEABLE)) return -EROFS; @@ -1194,7 +1201,16 @@ int mtd_write_oob(struct mtd_info *mtd, loff_t to, return ret; ledtrig_mtd_activity(); - return mtd->_write_oob(mtd, to, ops); + + /* Check the validity of a potential fallback on mtd->_write */ + if (!mtd->_write_oob && (!mtd->_write || ops->oobbuf)) + return -EOPNOTSUPP; + + if (mtd->_write_oob) + return mtd->_write_oob(mtd, to, ops); + else + return mtd->_write(mtd, to, ops->len, &ops->retlen, + ops->datbuf); } EXPORT_SYMBOL_GPL(mtd_write_oob); diff --git a/drivers/mtd/mtdpart.c b/drivers/mtd/mtdpart.c index f8d3a015cdad..52e2cb35fc79 100644 --- a/drivers/mtd/mtdpart.c +++ b/drivers/mtd/mtdpart.c @@ -322,22 +322,6 @@ static inline void free_partition(struct mtd_part *p) kfree(p); } -/** - * mtd_parse_part - parse MTD partition looking for subpartitions - * - * @slave: part that is supposed to be a container and should be parsed - * @types: NULL-terminated array with names of partition parsers to try - * - * Some partitions are kind of containers with extra subpartitions (volumes). - * There can be various formats of such containers. This function tries to use - * specified parsers to analyze given partition and registers found - * subpartitions on success. - */ -static int mtd_parse_part(struct mtd_part *slave, const char *const *types) -{ - return parse_mtd_partitions(&slave->mtd, types, NULL); -} - static struct mtd_part *allocate_partition(struct mtd_info *parent, const struct mtd_partition *part, int partno, uint64_t cur_offset) @@ -735,8 +719,8 @@ int add_mtd_partitions(struct mtd_info *master, add_mtd_device(&slave->mtd); mtd_add_partition_attrs(slave); - if (parts[i].types) - mtd_parse_part(slave, parts[i].types); + /* Look for subpartitions */ + parse_mtd_partitions(&slave->mtd, parts[i].types, NULL); cur_offset = slave->offset + slave->mtd.size; } @@ -812,6 +796,12 @@ static const char * const default_mtd_part_types[] = { NULL }; +/* Check DT only when looking for subpartitions. */ +static const char * const default_subpartition_types[] = { + "ofpart", + NULL +}; + static int mtd_part_do_parse(struct mtd_part_parser *parser, struct mtd_info *master, struct mtd_partitions *pparts, @@ -882,7 +872,9 @@ static int mtd_part_of_parse(struct mtd_info *master, const char *fixed = "fixed-partitions"; int ret, err = 0; - np = of_get_child_by_name(mtd_get_of_node(master), "partitions"); + np = mtd_get_of_node(master); + if (!mtd_is_partition(master)) + np = of_get_child_by_name(np, "partitions"); of_property_for_each_string(np, "compatible", prop, compat) { parser = mtd_part_get_compatible_parser(compat); if (!parser) @@ -945,7 +937,8 @@ int parse_mtd_partitions(struct mtd_info *master, const char *const *types, int ret, err = 0; if (!types) - types = default_mtd_part_types; + types = mtd_is_partition(master) ? default_subpartition_types : + default_mtd_part_types; for ( ; *types; types++) { /* diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 88c7d3b4ff8b..9033215e62ea 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -4,3 +4,4 @@ config MTD_NAND_CORE source "drivers/mtd/nand/onenand/Kconfig" source "drivers/mtd/nand/raw/Kconfig" +source "drivers/mtd/nand/spi/Kconfig" diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index 3f0cb87f1a57..7ecd80c0a66e 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -5,3 +5,4 @@ obj-$(CONFIG_MTD_NAND_CORE) += nandcore.o obj-y += onenand/ obj-y += raw/ +obj-y += spi/ diff --git a/drivers/mtd/nand/onenand/generic.c b/drivers/mtd/nand/onenand/generic.c index d5ccaf943b91..acad17ec6581 100644 --- a/drivers/mtd/nand/onenand/generic.c +++ b/drivers/mtd/nand/onenand/generic.c @@ -66,9 +66,8 @@ static int generic_onenand_probe(struct platform_device *pdev) goto out_iounmap; } - err = mtd_device_parse_register(&info->mtd, NULL, NULL, - pdata ? pdata->parts : NULL, - pdata ? pdata->nr_parts : 0); + err = mtd_device_register(&info->mtd, pdata ? pdata->parts : NULL, + pdata ? pdata->nr_parts : 0); platform_set_drvdata(pdev, info); diff --git a/drivers/mtd/nand/onenand/samsung.c b/drivers/mtd/nand/onenand/samsung.c index 4cce4c0311ca..e64d0fdf7eb5 100644 --- a/drivers/mtd/nand/onenand/samsung.c +++ b/drivers/mtd/nand/onenand/samsung.c @@ -933,9 +933,8 @@ static int s3c_onenand_probe(struct platform_device *pdev) if (s3c_read_reg(MEM_CFG_OFFSET) & ONENAND_SYS_CFG1_SYNC_READ) dev_info(&onenand->pdev->dev, "OneNAND Sync. Burst Read enabled\n"); - err = mtd_device_parse_register(mtd, NULL, NULL, - pdata ? pdata->parts : NULL, - pdata ? pdata->nr_parts : 0); + err = mtd_device_register(mtd, pdata ? pdata->parts : NULL, + pdata ? pdata->nr_parts : 0); if (err) { dev_err(&pdev->dev, "failed to parse partitions and register the MTD device\n"); onenand_release(mtd); diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig index 6871ff0fd300..5fc9a1bde4ac 100644 --- a/drivers/mtd/nand/raw/Kconfig +++ b/drivers/mtd/nand/raw/Kconfig @@ -44,12 +44,12 @@ config MTD_NAND_DENALI tristate config MTD_NAND_DENALI_PCI - tristate "Support Denali NAND controller on Intel Moorestown" + tristate "Support Denali NAND controller on Intel Moorestown" select MTD_NAND_DENALI depends on PCI - help - Enable the driver for NAND flash on Intel Moorestown, using the - Denali NAND controller core. + help + Enable the driver for NAND flash on Intel Moorestown, using the + Denali NAND controller core. config MTD_NAND_DENALI_DT tristate "Support Denali NAND controller as a DT device" @@ -77,9 +77,10 @@ config MTD_NAND_AMS_DELTA config MTD_NAND_OMAP2 tristate "NAND Flash device on OMAP2, OMAP3, OMAP4 and Keystone" - depends on (ARCH_OMAP2PLUS || ARCH_KEYSTONE) + depends on ARCH_OMAP2PLUS || ARCH_KEYSTONE || COMPILE_TEST + depends on HAS_IOMEM help - Support for NAND flash on Texas Instruments OMAP2, OMAP3, OMAP4 + Support for NAND flash on Texas Instruments OMAP2, OMAP3, OMAP4 and Keystone platforms. config MTD_NAND_OMAP_BCH @@ -137,7 +138,7 @@ config MTD_NAND_NDFC depends on 4xx select MTD_NAND_ECC_SMC help - NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs + NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs config MTD_NAND_S3C2410_CLKSTOP bool "Samsung S3C NAND IDLE clock stop" @@ -152,6 +153,7 @@ config MTD_NAND_S3C2410_CLKSTOP config MTD_NAND_TANGO tristate "NAND Flash support for Tango chips" depends on ARCH_TANGO || COMPILE_TEST + depends on HAS_IOMEM help Enables the NAND Flash controller on Tango chips. @@ -168,40 +170,40 @@ config MTD_NAND_DISKONCHIP these devices. config MTD_NAND_DISKONCHIP_PROBE_ADVANCED - bool "Advanced detection options for DiskOnChip" - depends on MTD_NAND_DISKONCHIP - help - This option allows you to specify nonstandard address at which to - probe for a DiskOnChip, or to change the detection options. You - are unlikely to need any of this unless you are using LinuxBIOS. - Say 'N'. + bool "Advanced detection options for DiskOnChip" + depends on MTD_NAND_DISKONCHIP + help + This option allows you to specify nonstandard address at which to + probe for a DiskOnChip, or to change the detection options. You + are unlikely to need any of this unless you are using LinuxBIOS. + Say 'N'. config MTD_NAND_DISKONCHIP_PROBE_ADDRESS - hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED - depends on MTD_NAND_DISKONCHIP - default "0" - ---help--- - By default, the probe for DiskOnChip devices will look for a - DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. - This option allows you to specify a single address at which to probe - for the device, which is useful if you have other devices in that - range which get upset when they are probed. - - (Note that on PowerPC, the normal probe will only check at - 0xE4000000.) - - Normally, you should leave this set to zero, to allow the probe at - the normal addresses. + hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED + depends on MTD_NAND_DISKONCHIP + default "0" + help + By default, the probe for DiskOnChip devices will look for a + DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. + This option allows you to specify a single address at which to probe + for the device, which is useful if you have other devices in that + range which get upset when they are probed. + + (Note that on PowerPC, the normal probe will only check at + 0xE4000000.) + + Normally, you should leave this set to zero, to allow the probe at + the normal addresses. config MTD_NAND_DISKONCHIP_PROBE_HIGH - bool "Probe high addresses" - depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED - help - By default, the probe for DiskOnChip devices will look for a - DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. - This option changes to make it probe between 0xFFFC8000 and - 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be - useful to you. Say 'N'. + bool "Probe high addresses" + depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED + help + By default, the probe for DiskOnChip devices will look for a + DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. + This option changes to make it probe between 0xFFFC8000 and + 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be + useful to you. Say 'N'. config MTD_NAND_DISKONCHIP_BBTWRITE bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP" @@ -247,7 +249,8 @@ config MTD_NAND_DOCG4 config MTD_NAND_SHARPSL tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)" - depends on ARCH_PXA + depends on ARCH_PXA || COMPILE_TEST + depends on HAS_IOMEM config MTD_NAND_CAFE tristate "NAND support for OLPC CAFÉ chip" @@ -274,7 +277,9 @@ config MTD_NAND_CS553X config MTD_NAND_ATMEL tristate "Support for NAND Flash / SmartMedia on AT91" - depends on ARCH_AT91 + depends on ARCH_AT91 || COMPILE_TEST + depends on HAS_IOMEM + select GENERIC_ALLOCATOR select MFD_ATMEL_SMC help Enables support for NAND Flash / Smart Media Card interface @@ -294,7 +299,8 @@ config MTD_NAND_MARVELL config MTD_NAND_SLC_LPC32XX tristate "NXP LPC32xx SLC Controller" - depends on ARCH_LPC32XX + depends on ARCH_LPC32XX || COMPILE_TEST + depends on HAS_IOMEM help Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell chips) NAND controller. This is the default for the PHYTEC 3250 @@ -305,7 +311,8 @@ config MTD_NAND_SLC_LPC32XX config MTD_NAND_MLC_LPC32XX tristate "NXP LPC32xx MLC Controller" - depends on ARCH_LPC32XX + depends on ARCH_LPC32XX || COMPILE_TEST + depends on HAS_IOMEM help Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND controller. This is the default for the WORK92105 controller @@ -339,17 +346,18 @@ config MTD_NAND_NANDSIM MTD nand layer. config MTD_NAND_GPMI_NAND - tristate "GPMI NAND Flash Controller driver" - depends on MTD_NAND && MXS_DMA - help - Enables NAND Flash support for IMX23, IMX28 or IMX6. - The GPMI controller is very powerful, with the help of BCH - module, it can do the hardware ECC. The GPMI supports several - NAND flashs at the same time. + tristate "GPMI NAND Flash Controller driver" + depends on MXS_DMA + help + Enables NAND Flash support for IMX23, IMX28 or IMX6. + The GPMI controller is very powerful, with the help of BCH + module, it can do the hardware ECC. The GPMI supports several + NAND flashs at the same time. config MTD_NAND_BRCMNAND tristate "Broadcom STB NAND controller" - depends on ARM || ARM64 || MIPS + depends on ARM || ARM64 || MIPS || COMPILE_TEST + depends on HAS_IOMEM help Enables the Broadcom NAND controller driver. The controller was originally designed for Set-Top Box but is used on various BCM7xxx, @@ -358,6 +366,7 @@ config MTD_NAND_BRCMNAND config MTD_NAND_BCM47XXNFLASH tristate "Support for NAND flash on BCM4706 BCMA bus" depends on BCMA_NFLASH + depends on BCMA help BCMA bus can have various flash memories attached, they are registered by bcma as platform devices. This enables driver for @@ -399,7 +408,8 @@ config MTD_NAND_FSL_ELBC config MTD_NAND_FSL_IFC tristate "NAND support for Freescale IFC controller" - depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A + depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A || COMPILE_TEST + depends on HAS_IOMEM select FSL_IFC select MEMORY help @@ -437,7 +447,8 @@ config MTD_NAND_VF610_NFC config MTD_NAND_MXC tristate "MXC NAND support" - depends on ARCH_MXC + depends on ARCH_MXC || COMPILE_TEST + depends on HAS_IOMEM help This enables the driver for the NAND flash controller on the MXC processors. @@ -451,15 +462,17 @@ config MTD_NAND_SH_FLCTL for NAND Flash using FLCTL. config MTD_NAND_DAVINCI - tristate "Support NAND on DaVinci/Keystone SoC" - depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF) - help + tristate "Support NAND on DaVinci/Keystone SoC" + depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF) || COMPILE_TEST + depends on HAS_IOMEM + help Enable the driver for NAND flash chips on Texas Instruments DaVinci/Keystone processors. config MTD_NAND_TXX9NDFMC tristate "NAND Flash support for TXx9 SoC" - depends on SOC_TX4938 || SOC_TX4939 + depends on SOC_TX4938 || SOC_TX4939 || COMPILE_TEST + depends on HAS_IOMEM help This enables the NAND flash controller on the TXx9 SoCs. @@ -471,28 +484,31 @@ config MTD_NAND_SOCRATES config MTD_NAND_NUC900 tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards." - depends on ARCH_W90X900 + depends on ARCH_W90X900 || COMPILE_TEST + depends on HAS_IOMEM help This enables the driver for the NAND Flash on evaluation board based on w90p910 / NUC9xx. config MTD_NAND_JZ4740 tristate "Support for JZ4740 SoC NAND controller" - depends on MACH_JZ4740 + depends on MACH_JZ4740 || COMPILE_TEST + depends on HAS_IOMEM help - Enables support for NAND Flash on JZ4740 SoC based boards. + Enables support for NAND Flash on JZ4740 SoC based boards. config MTD_NAND_JZ4780 tristate "Support for NAND on JZ4780 SoC" - depends on MACH_JZ4780 && JZ4780_NEMC + depends on JZ4780_NEMC help Enables support for NAND Flash connected to the NEMC on JZ4780 SoC based boards, using the BCH controller for hardware error correction. config MTD_NAND_FSMC tristate "Support for NAND on ST Micros FSMC" - depends on OF - depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300 + depends on OF && HAS_IOMEM + depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300 || \ + COMPILE_TEST help Enables support for NAND Flash chips on the ST Microelectronics Flexible Static Memory Controller (FSMC) @@ -506,19 +522,22 @@ config MTD_NAND_XWAY config MTD_NAND_SUNXI tristate "Support for NAND on Allwinner SoCs" - depends on ARCH_SUNXI + depends on ARCH_SUNXI || COMPILE_TEST + depends on HAS_IOMEM help Enables support for NAND Flash chips on Allwinner SoCs. config MTD_NAND_HISI504 tristate "Support for NAND controller on Hisilicon SoC Hip04" depends on ARCH_HISI || COMPILE_TEST + depends on HAS_IOMEM help Enables support for NAND controller on Hisilicon SoC Hip04. config MTD_NAND_QCOM tristate "Support for NAND on QCOM SoCs" - depends on ARCH_QCOM + depends on ARCH_QCOM || COMPILE_TEST + depends on HAS_IOMEM help Enables support for NAND flash chips on SoCs containing the EBI2 NAND controller. This controller is found on IPQ806x SoC. @@ -526,8 +545,20 @@ config MTD_NAND_QCOM config MTD_NAND_MTK tristate "Support for NAND controller on MTK SoCs" depends on ARCH_MEDIATEK || COMPILE_TEST + depends on HAS_IOMEM help Enables support for NAND controller on MTK SoCs. This controller is found on mt27xx, mt81xx, mt65xx SoCs. +config MTD_NAND_TEGRA + tristate "Support for NAND controller on NVIDIA Tegra" + depends on ARCH_TEGRA || COMPILE_TEST + depends on HAS_IOMEM + help + Enables support for NAND flash controller on NVIDIA Tegra SoC. + The driver has been developed and tested on a Tegra 2 SoC. DMA + support, raw read/write page as well as HW ECC read/write page + is supported. Extra OOB bytes when using HW ECC are currently + not supported. + endif # MTD_NAND diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile index 165b7ef9e9a1..d5a5f9832b88 100644 --- a/drivers/mtd/nand/raw/Makefile +++ b/drivers/mtd/nand/raw/Makefile @@ -56,6 +56,7 @@ obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/ obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o obj-$(CONFIG_MTD_NAND_MTK) += mtk_ecc.o mtk_nand.o +obj-$(CONFIG_MTD_NAND_TEGRA) += tegra_nand.o nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o nand-objs += nand_amd.o diff --git a/drivers/mtd/nand/raw/atmel/nand-controller.c b/drivers/mtd/nand/raw/atmel/nand-controller.c index 12f6753d47ae..a068b214ebaa 100644 --- a/drivers/mtd/nand/raw/atmel/nand-controller.c +++ b/drivers/mtd/nand/raw/atmel/nand-controller.c @@ -52,7 +52,6 @@ #include <linux/dma-mapping.h> #include <linux/dmaengine.h> #include <linux/genalloc.h> -#include <linux/gpio.h> #include <linux/gpio/consumer.h> #include <linux/interrupt.h> #include <linux/mfd/syscon.h> @@ -129,6 +128,11 @@ #define DEFAULT_TIMEOUT_MS 1000 #define MIN_DMA_LEN 128 +static bool atmel_nand_avoid_dma __read_mostly; + +MODULE_PARM_DESC(avoiddma, "Avoid using DMA"); +module_param_named(avoiddma, atmel_nand_avoid_dma, bool, 0400); + enum atmel_nand_rb_type { ATMEL_NAND_NO_RB, ATMEL_NAND_NATIVE_RB, @@ -197,7 +201,7 @@ struct atmel_nand_controller_ops { int (*remove)(struct atmel_nand_controller *nc); void (*nand_init)(struct atmel_nand_controller *nc, struct atmel_nand *nand); - int (*ecc_init)(struct atmel_nand *nand); + int (*ecc_init)(struct nand_chip *chip); int (*setup_data_interface)(struct atmel_nand *nand, int csline, const struct nand_data_interface *conf); }; @@ -211,7 +215,7 @@ struct atmel_nand_controller_caps { }; struct atmel_nand_controller { - struct nand_hw_control base; + struct nand_controller base; const struct atmel_nand_controller_caps *caps; struct device *dev; struct regmap *smc; @@ -222,7 +226,7 @@ struct atmel_nand_controller { }; static inline struct atmel_nand_controller * -to_nand_controller(struct nand_hw_control *ctl) +to_nand_controller(struct nand_controller *ctl) { return container_of(ctl, struct atmel_nand_controller, base); } @@ -234,7 +238,7 @@ struct atmel_smc_nand_controller { }; static inline struct atmel_smc_nand_controller * -to_smc_nand_controller(struct nand_hw_control *ctl) +to_smc_nand_controller(struct nand_controller *ctl) { return container_of(to_nand_controller(ctl), struct atmel_smc_nand_controller, base); @@ -258,7 +262,7 @@ struct atmel_hsmc_nand_controller { }; static inline struct atmel_hsmc_nand_controller * -to_hsmc_nand_controller(struct nand_hw_control *ctl) +to_hsmc_nand_controller(struct nand_controller *ctl) { return container_of(to_nand_controller(ctl), struct atmel_hsmc_nand_controller, base); @@ -1128,9 +1132,8 @@ static int atmel_nand_pmecc_init(struct nand_chip *chip) return 0; } -static int atmel_nand_ecc_init(struct atmel_nand *nand) +static int atmel_nand_ecc_init(struct nand_chip *chip) { - struct nand_chip *chip = &nand->base; struct atmel_nand_controller *nc; int ret; @@ -1165,12 +1168,11 @@ static int atmel_nand_ecc_init(struct atmel_nand *nand) return 0; } -static int atmel_hsmc_nand_ecc_init(struct atmel_nand *nand) +static int atmel_hsmc_nand_ecc_init(struct nand_chip *chip) { - struct nand_chip *chip = &nand->base; int ret; - ret = atmel_nand_ecc_init(nand); + ret = atmel_nand_ecc_init(chip); if (ret) return ret; @@ -1553,23 +1555,7 @@ static void atmel_hsmc_nand_init(struct atmel_nand_controller *nc, chip->select_chip = atmel_hsmc_nand_select_chip; } -static int atmel_nand_detect(struct atmel_nand *nand) -{ - struct nand_chip *chip = &nand->base; - struct mtd_info *mtd = nand_to_mtd(chip); - struct atmel_nand_controller *nc; - int ret; - - nc = to_nand_controller(chip->controller); - - ret = nand_scan_ident(mtd, nand->numcs, NULL); - if (ret) - dev_err(nc->dev, "nand_scan_ident() failed: %d\n", ret); - - return ret; -} - -static int atmel_nand_unregister(struct atmel_nand *nand) +static int atmel_nand_controller_remove_nand(struct atmel_nand *nand) { struct nand_chip *chip = &nand->base; struct mtd_info *mtd = nand_to_mtd(chip); @@ -1585,60 +1571,6 @@ static int atmel_nand_unregister(struct atmel_nand *nand) return 0; } -static int atmel_nand_register(struct atmel_nand *nand) -{ - struct nand_chip *chip = &nand->base; - struct mtd_info *mtd = nand_to_mtd(chip); - struct atmel_nand_controller *nc; - int ret; - - nc = to_nand_controller(chip->controller); - - if (nc->caps->legacy_of_bindings || !nc->dev->of_node) { - /* - * We keep the MTD name unchanged to avoid breaking platforms - * where the MTD cmdline parser is used and the bootloader - * has not been updated to use the new naming scheme. - */ - mtd->name = "atmel_nand"; - } else if (!mtd->name) { - /* - * If the new bindings are used and the bootloader has not been - * updated to pass a new mtdparts parameter on the cmdline, you - * should define the following property in your nand node: - * - * label = "atmel_nand"; - * - * This way, mtd->name will be set by the core when - * nand_set_flash_node() is called. - */ - mtd->name = devm_kasprintf(nc->dev, GFP_KERNEL, - "%s:nand.%d", dev_name(nc->dev), - nand->cs[0].id); - if (!mtd->name) { - dev_err(nc->dev, "Failed to allocate mtd->name\n"); - return -ENOMEM; - } - } - - ret = nand_scan_tail(mtd); - if (ret) { - dev_err(nc->dev, "nand_scan_tail() failed: %d\n", ret); - return ret; - } - - ret = mtd_device_register(mtd, NULL, 0); - if (ret) { - dev_err(nc->dev, "Failed to register mtd device: %d\n", ret); - nand_cleanup(chip); - return ret; - } - - list_add_tail(&nand->node, &nc->chips); - - return 0; -} - static struct atmel_nand *atmel_nand_create(struct atmel_nand_controller *nc, struct device_node *np, int reg_cells) @@ -1750,6 +1682,8 @@ static int atmel_nand_controller_add_nand(struct atmel_nand_controller *nc, struct atmel_nand *nand) { + struct nand_chip *chip = &nand->base; + struct mtd_info *mtd = nand_to_mtd(chip); int ret; /* No card inserted, skip this NAND. */ @@ -1760,15 +1694,22 @@ atmel_nand_controller_add_nand(struct atmel_nand_controller *nc, nc->caps->ops->nand_init(nc, nand); - ret = atmel_nand_detect(nand); - if (ret) + ret = nand_scan(mtd, nand->numcs); + if (ret) { + dev_err(nc->dev, "NAND scan failed: %d\n", ret); return ret; + } - ret = nc->caps->ops->ecc_init(nand); - if (ret) + ret = mtd_device_register(mtd, NULL, 0); + if (ret) { + dev_err(nc->dev, "Failed to register mtd device: %d\n", ret); + nand_cleanup(chip); return ret; + } + + list_add_tail(&nand->node, &nc->chips); - return atmel_nand_register(nand); + return 0; } static int @@ -1778,7 +1719,7 @@ atmel_nand_controller_remove_nands(struct atmel_nand_controller *nc) int ret; list_for_each_entry_safe(nand, tmp, &nc->chips, node) { - ret = atmel_nand_unregister(nand); + ret = atmel_nand_controller_remove_nand(nand); if (ret) return ret; } @@ -1953,6 +1894,51 @@ static const struct of_device_id atmel_matrix_of_ids[] = { { /* sentinel */ }, }; +static int atmel_nand_attach_chip(struct nand_chip *chip) +{ + struct atmel_nand_controller *nc = to_nand_controller(chip->controller); + struct atmel_nand *nand = to_atmel_nand(chip); + struct mtd_info *mtd = nand_to_mtd(chip); + int ret; + + ret = nc->caps->ops->ecc_init(chip); + if (ret) + return ret; + + if (nc->caps->legacy_of_bindings || !nc->dev->of_node) { + /* + * We keep the MTD name unchanged to avoid breaking platforms + * where the MTD cmdline parser is used and the bootloader + * has not been updated to use the new naming scheme. + */ + mtd->name = "atmel_nand"; + } else if (!mtd->name) { + /* + * If the new bindings are used and the bootloader has not been + * updated to pass a new mtdparts parameter on the cmdline, you + * should define the following property in your nand node: + * + * label = "atmel_nand"; + * + * This way, mtd->name will be set by the core when + * nand_set_flash_node() is called. + */ + mtd->name = devm_kasprintf(nc->dev, GFP_KERNEL, + "%s:nand.%d", dev_name(nc->dev), + nand->cs[0].id); + if (!mtd->name) { + dev_err(nc->dev, "Failed to allocate mtd->name\n"); + return -ENOMEM; + } + } + + return 0; +} + +static const struct nand_controller_ops atmel_nand_controller_ops = { + .attach_chip = atmel_nand_attach_chip, +}; + static int atmel_nand_controller_init(struct atmel_nand_controller *nc, struct platform_device *pdev, const struct atmel_nand_controller_caps *caps) @@ -1961,7 +1947,8 @@ static int atmel_nand_controller_init(struct atmel_nand_controller *nc, struct device_node *np = dev->of_node; int ret; - nand_hw_control_init(&nc->base); + nand_controller_init(&nc->base); + nc->base.ops = &atmel_nand_controller_ops; INIT_LIST_HEAD(&nc->chips); nc->dev = dev; nc->caps = caps; @@ -1977,7 +1964,7 @@ static int atmel_nand_controller_init(struct atmel_nand_controller *nc, return ret; } - if (nc->caps->has_dma) { + if (nc->caps->has_dma && !atmel_nand_avoid_dma) { dma_cap_mask_t mask; dma_cap_zero(mask); @@ -2045,7 +2032,7 @@ atmel_smc_nand_controller_init(struct atmel_smc_nand_controller *nc) return ret; } - nc->ebi_csa_offs = (unsigned int)match->data; + nc->ebi_csa_offs = (uintptr_t)match->data; /* * The at91sam9263 has 2 EBIs, if the NAND controller is under EBI1 @@ -2214,9 +2201,9 @@ atmel_hsmc_nand_controller_init(struct atmel_hsmc_nand_controller *nc) return -ENOMEM; } - nc->sram.virt = gen_pool_dma_alloc(nc->sram.pool, - ATMEL_NFC_SRAM_SIZE, - &nc->sram.dma); + nc->sram.virt = (void __iomem *)gen_pool_dma_alloc(nc->sram.pool, + ATMEL_NFC_SRAM_SIZE, + &nc->sram.dma); if (!nc->sram.virt) { dev_err(nc->base.dev, "Could not allocate memory from the NFC SRAM pool\n"); diff --git a/drivers/mtd/nand/raw/au1550nd.c b/drivers/mtd/nand/raw/au1550nd.c index df0ef1f1e2f5..35f5c84cd331 100644 --- a/drivers/mtd/nand/raw/au1550nd.c +++ b/drivers/mtd/nand/raw/au1550nd.c @@ -8,7 +8,6 @@ */ #include <linux/slab.h> -#include <linux/gpio.h> #include <linux/module.h> #include <linux/interrupt.h> #include <linux/mtd/mtd.h> diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c index 1306aaa7a8bf..4b90d5b380c2 100644 --- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c +++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c @@ -114,7 +114,7 @@ enum { struct brcmnand_controller { struct device *dev; - struct nand_hw_control controller; + struct nand_controller controller; void __iomem *nand_base; void __iomem *nand_fc; /* flash cache */ void __iomem *flash_dma_base; @@ -2208,6 +2208,40 @@ static int brcmnand_setup_dev(struct brcmnand_host *host) return 0; } +static int brcmnand_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct brcmnand_host *host = nand_get_controller_data(chip); + int ret; + + chip->options |= NAND_NO_SUBPAGE_WRITE; + /* + * Avoid (for instance) kmap()'d buffers from JFFS2, which we can't DMA + * to/from, and have nand_base pass us a bounce buffer instead, as + * needed. + */ + chip->options |= NAND_USE_BOUNCE_BUFFER; + + if (chip->bbt_options & NAND_BBT_USE_FLASH) + chip->bbt_options |= NAND_BBT_NO_OOB; + + if (brcmnand_setup_dev(host)) + return -ENXIO; + + chip->ecc.size = host->hwcfg.sector_size_1k ? 1024 : 512; + + /* only use our internal HW threshold */ + mtd->bitflip_threshold = 1; + + ret = brcmstb_choose_ecc_layout(host); + + return ret; +} + +static const struct nand_controller_ops brcmnand_controller_ops = { + .attach_chip = brcmnand_attach_chip, +}; + static int brcmnand_init_cs(struct brcmnand_host *host, struct device_node *dn) { struct brcmnand_controller *ctrl = host->ctrl; @@ -2267,33 +2301,7 @@ static int brcmnand_init_cs(struct brcmnand_host *host, struct device_node *dn) nand_writereg(ctrl, cfg_offs, nand_readreg(ctrl, cfg_offs) & ~CFG_BUS_WIDTH); - ret = nand_scan_ident(mtd, 1, NULL); - if (ret) - return ret; - - chip->options |= NAND_NO_SUBPAGE_WRITE; - /* - * Avoid (for instance) kmap()'d buffers from JFFS2, which we can't DMA - * to/from, and have nand_base pass us a bounce buffer instead, as - * needed. - */ - chip->options |= NAND_USE_BOUNCE_BUFFER; - - if (chip->bbt_options & NAND_BBT_USE_FLASH) - chip->bbt_options |= NAND_BBT_NO_OOB; - - if (brcmnand_setup_dev(host)) - return -ENXIO; - - chip->ecc.size = host->hwcfg.sector_size_1k ? 1024 : 512; - /* only use our internal HW threshold */ - mtd->bitflip_threshold = 1; - - ret = brcmstb_choose_ecc_layout(host); - if (ret) - return ret; - - ret = nand_scan_tail(mtd); + ret = nand_scan(mtd, 1); if (ret) return ret; @@ -2433,7 +2441,8 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc) init_completion(&ctrl->done); init_completion(&ctrl->dma_done); - nand_hw_control_init(&ctrl->controller); + nand_controller_init(&ctrl->controller); + ctrl->controller.ops = &brcmnand_controller_ops; INIT_LIST_HEAD(&ctrl->host_list); /* NAND register range */ diff --git a/drivers/mtd/nand/raw/cafe_nand.c b/drivers/mtd/nand/raw/cafe_nand.c index d721f489b38b..1dbe43adcfe7 100644 --- a/drivers/mtd/nand/raw/cafe_nand.c +++ b/drivers/mtd/nand/raw/cafe_nand.c @@ -67,6 +67,7 @@ struct cafe_priv { int nr_data; int data_pos; int page_addr; + bool usedma; dma_addr_t dmaaddr; unsigned char *dmabuf; }; @@ -121,7 +122,7 @@ static void cafe_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) struct nand_chip *chip = mtd_to_nand(mtd); struct cafe_priv *cafe = nand_get_controller_data(chip); - if (usedma) + if (cafe->usedma) memcpy(cafe->dmabuf + cafe->datalen, buf, len); else memcpy_toio(cafe->mmio + CAFE_NAND_WRITE_DATA + cafe->datalen, buf, len); @@ -137,7 +138,7 @@ static void cafe_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) struct nand_chip *chip = mtd_to_nand(mtd); struct cafe_priv *cafe = nand_get_controller_data(chip); - if (usedma) + if (cafe->usedma) memcpy(buf, cafe->dmabuf + cafe->datalen, len); else memcpy_fromio(buf, cafe->mmio + CAFE_NAND_READ_DATA + cafe->datalen, len); @@ -253,7 +254,7 @@ static void cafe_nand_cmdfunc(struct mtd_info *mtd, unsigned command, /* NB: The datasheet lies -- we really should be subtracting 1 here */ cafe_writel(cafe, cafe->datalen, NAND_DATA_LEN); cafe_writel(cafe, 0x90000000, NAND_IRQ); - if (usedma && (ctl1 & (3<<25))) { + if (cafe->usedma && (ctl1 & (3<<25))) { uint32_t dmactl = 0xc0000000 + cafe->datalen; /* If WR or RD bits set, set up DMA */ if (ctl1 & (1<<26)) { @@ -345,11 +346,6 @@ static irqreturn_t cafe_nand_interrupt(int irq, void *id) return IRQ_HANDLED; } -static void cafe_nand_bug(struct mtd_info *mtd) -{ - BUG(); -} - static int cafe_nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { @@ -598,6 +594,76 @@ static int cafe_mul(int x) return gf4096_mul(x, 0xe01); } +static int cafe_nand_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct cafe_priv *cafe = nand_get_controller_data(chip); + int err = 0; + + cafe->dmabuf = dma_alloc_coherent(&cafe->pdev->dev, 2112, + &cafe->dmaaddr, GFP_KERNEL); + if (!cafe->dmabuf) + return -ENOMEM; + + /* Set up DMA address */ + cafe_writel(cafe, lower_32_bits(cafe->dmaaddr), NAND_DMA_ADDR0); + cafe_writel(cafe, upper_32_bits(cafe->dmaaddr), NAND_DMA_ADDR1); + + cafe_dev_dbg(&cafe->pdev->dev, "Set DMA address to %x (virt %p)\n", + cafe_readl(cafe, NAND_DMA_ADDR0), cafe->dmabuf); + + /* Restore the DMA flag */ + cafe->usedma = usedma; + + cafe->ctl2 = BIT(27); /* Reed-Solomon ECC */ + if (mtd->writesize == 2048) + cafe->ctl2 |= BIT(29); /* 2KiB page size */ + + /* Set up ECC according to the type of chip we found */ + mtd_set_ooblayout(mtd, &cafe_ooblayout_ops); + if (mtd->writesize == 2048) { + cafe->nand.bbt_td = &cafe_bbt_main_descr_2048; + cafe->nand.bbt_md = &cafe_bbt_mirror_descr_2048; + } else if (mtd->writesize == 512) { + cafe->nand.bbt_td = &cafe_bbt_main_descr_512; + cafe->nand.bbt_md = &cafe_bbt_mirror_descr_512; + } else { + dev_warn(&cafe->pdev->dev, + "Unexpected NAND flash writesize %d. Aborting\n", + mtd->writesize); + err = -ENOTSUPP; + goto out_free_dma; + } + + cafe->nand.ecc.mode = NAND_ECC_HW_SYNDROME; + cafe->nand.ecc.size = mtd->writesize; + cafe->nand.ecc.bytes = 14; + cafe->nand.ecc.strength = 4; + cafe->nand.ecc.write_page = cafe_nand_write_page_lowlevel; + cafe->nand.ecc.write_oob = cafe_nand_write_oob; + cafe->nand.ecc.read_page = cafe_nand_read_page; + cafe->nand.ecc.read_oob = cafe_nand_read_oob; + + return 0; + + out_free_dma: + dma_free_coherent(&cafe->pdev->dev, 2112, cafe->dmabuf, cafe->dmaaddr); + + return err; +} + +static void cafe_nand_detach_chip(struct nand_chip *chip) +{ + struct cafe_priv *cafe = nand_get_controller_data(chip); + + dma_free_coherent(&cafe->pdev->dev, 2112, cafe->dmabuf, cafe->dmaaddr); +} + +static const struct nand_controller_ops cafe_nand_controller_ops = { + .attach_chip = cafe_nand_attach_chip, + .detach_chip = cafe_nand_detach_chip, +}; + static int cafe_nand_probe(struct pci_dev *pdev, const struct pci_device_id *ent) { @@ -605,7 +671,6 @@ static int cafe_nand_probe(struct pci_dev *pdev, struct cafe_priv *cafe; uint32_t ctrl; int err = 0; - int old_dma; /* Very old versions shared the same PCI ident for all three functions on the chip. Verify the class too... */ @@ -713,65 +778,15 @@ static int cafe_nand_probe(struct pci_dev *pdev, cafe_readl(cafe, GLOBAL_CTRL), cafe_readl(cafe, GLOBAL_IRQ_MASK)); - /* Do not use the DMA for the nand_scan_ident() */ - old_dma = usedma; - usedma = 0; + /* Do not use the DMA during the NAND identification */ + cafe->usedma = 0; /* Scan to find existence of the device */ - err = nand_scan_ident(mtd, 2, NULL); + cafe->nand.dummy_controller.ops = &cafe_nand_controller_ops; + err = nand_scan(mtd, 2); if (err) goto out_irq; - cafe->dmabuf = dma_alloc_coherent(&cafe->pdev->dev, 2112, - &cafe->dmaaddr, GFP_KERNEL); - if (!cafe->dmabuf) { - err = -ENOMEM; - goto out_irq; - } - - /* Set up DMA address */ - cafe_writel(cafe, lower_32_bits(cafe->dmaaddr), NAND_DMA_ADDR0); - cafe_writel(cafe, upper_32_bits(cafe->dmaaddr), NAND_DMA_ADDR1); - - cafe_dev_dbg(&cafe->pdev->dev, "Set DMA address to %x (virt %p)\n", - cafe_readl(cafe, NAND_DMA_ADDR0), cafe->dmabuf); - - /* Restore the DMA flag */ - usedma = old_dma; - - cafe->ctl2 = 1<<27; /* Reed-Solomon ECC */ - if (mtd->writesize == 2048) - cafe->ctl2 |= 1<<29; /* 2KiB page size */ - - /* Set up ECC according to the type of chip we found */ - mtd_set_ooblayout(mtd, &cafe_ooblayout_ops); - if (mtd->writesize == 2048) { - cafe->nand.bbt_td = &cafe_bbt_main_descr_2048; - cafe->nand.bbt_md = &cafe_bbt_mirror_descr_2048; - } else if (mtd->writesize == 512) { - cafe->nand.bbt_td = &cafe_bbt_main_descr_512; - cafe->nand.bbt_md = &cafe_bbt_mirror_descr_512; - } else { - pr_warn("Unexpected NAND flash writesize %d. Aborting\n", - mtd->writesize); - goto out_free_dma; - } - cafe->nand.ecc.mode = NAND_ECC_HW_SYNDROME; - cafe->nand.ecc.size = mtd->writesize; - cafe->nand.ecc.bytes = 14; - cafe->nand.ecc.strength = 4; - cafe->nand.ecc.hwctl = (void *)cafe_nand_bug; - cafe->nand.ecc.calculate = (void *)cafe_nand_bug; - cafe->nand.ecc.correct = (void *)cafe_nand_bug; - cafe->nand.ecc.write_page = cafe_nand_write_page_lowlevel; - cafe->nand.ecc.write_oob = cafe_nand_write_oob; - cafe->nand.ecc.read_page = cafe_nand_read_page; - cafe->nand.ecc.read_oob = cafe_nand_read_oob; - - err = nand_scan_tail(mtd); - if (err) - goto out_free_dma; - pci_set_drvdata(pdev, mtd); mtd->name = "cafe_nand"; @@ -783,8 +798,6 @@ static int cafe_nand_probe(struct pci_dev *pdev, out_cleanup_nand: nand_cleanup(&cafe->nand); - out_free_dma: - dma_free_coherent(&cafe->pdev->dev, 2112, cafe->dmabuf, cafe->dmaaddr); out_irq: /* Disable NAND IRQ in global IRQ mask register */ cafe_writel(cafe, ~1 & cafe_readl(cafe, GLOBAL_IRQ_MASK), GLOBAL_IRQ_MASK); diff --git a/drivers/mtd/nand/raw/cmx270_nand.c b/drivers/mtd/nand/raw/cmx270_nand.c index 02d6751e9efe..b66e254b6802 100644 --- a/drivers/mtd/nand/raw/cmx270_nand.c +++ b/drivers/mtd/nand/raw/cmx270_nand.c @@ -200,8 +200,8 @@ static int __init cmx270_init(void) } /* Register the partitions */ - ret = mtd_device_parse_register(cmx270_nand_mtd, NULL, NULL, - partition_info, NUM_PARTITIONS); + ret = mtd_device_register(cmx270_nand_mtd, partition_info, + NUM_PARTITIONS); if (ret) goto err_scan; diff --git a/drivers/mtd/nand/raw/cs553x_nand.c b/drivers/mtd/nand/raw/cs553x_nand.c index 82269fde9e66..beafad62e7d5 100644 --- a/drivers/mtd/nand/raw/cs553x_nand.c +++ b/drivers/mtd/nand/raw/cs553x_nand.c @@ -310,8 +310,7 @@ static int __init cs553x_init(void) for (i = 0; i < NR_CS553X_CONTROLLERS; i++) { if (cs553x_mtd[i]) { /* If any devices registered, return success. Else the last error. */ - mtd_device_parse_register(cs553x_mtd[i], NULL, NULL, - NULL, 0); + mtd_device_register(cs553x_mtd[i], NULL, 0); err = 0; } } diff --git a/drivers/mtd/nand/raw/davinci_nand.c b/drivers/mtd/nand/raw/davinci_nand.c index cd12e5abafde..40145e206a6b 100644 --- a/drivers/mtd/nand/raw/davinci_nand.c +++ b/drivers/mtd/nand/raw/davinci_nand.c @@ -53,15 +53,14 @@ struct davinci_nand_info { struct nand_chip chip; - struct device *dev; + struct platform_device *pdev; bool is_readmode; void __iomem *base; void __iomem *vaddr; - uint32_t ioaddr; - uint32_t current_cs; + void __iomem *current_cs; uint32_t mask_chipsel; uint32_t mask_ale; @@ -102,17 +101,17 @@ static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) { struct davinci_nand_info *info = to_davinci_nand(mtd); - uint32_t addr = info->current_cs; + void __iomem *addr = info->current_cs; struct nand_chip *nand = mtd_to_nand(mtd); /* Did the control lines change? */ if (ctrl & NAND_CTRL_CHANGE) { if ((ctrl & NAND_CTRL_CLE) == NAND_CTRL_CLE) - addr |= info->mask_cle; + addr += info->mask_cle; else if ((ctrl & NAND_CTRL_ALE) == NAND_CTRL_ALE) - addr |= info->mask_ale; + addr += info->mask_ale; - nand->IO_ADDR_W = (void __iomem __force *)addr; + nand->IO_ADDR_W = addr; } if (cmd != NAND_CMD_NONE) @@ -122,14 +121,14 @@ static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd, static void nand_davinci_select_chip(struct mtd_info *mtd, int chip) { struct davinci_nand_info *info = to_davinci_nand(mtd); - uint32_t addr = info->ioaddr; + + info->current_cs = info->vaddr; /* maybe kick in a second chipselect */ if (chip > 0) - addr |= info->mask_chipsel; - info->current_cs = addr; + info->current_cs += info->mask_chipsel; - info->chip.IO_ADDR_W = (void __iomem __force *)addr; + info->chip.IO_ADDR_W = info->current_cs; info->chip.IO_ADDR_R = info->chip.IO_ADDR_W; } @@ -319,7 +318,7 @@ static int nand_davinci_correct_4bit(struct mtd_info *mtd, /* Unpack ten bytes into eight 10 bit values. We know we're * little-endian, and use type punning for less shifting/masking. */ - if (WARN_ON(0x01 & (unsigned) ecc_code)) + if (WARN_ON(0x01 & (uintptr_t)ecc_code)) return -EINVAL; ecc16 = (unsigned short *)ecc_code; @@ -441,9 +440,9 @@ static void nand_davinci_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) { struct nand_chip *chip = mtd_to_nand(mtd); - if ((0x03 & ((unsigned)buf)) == 0 && (0x03 & len) == 0) + if ((0x03 & ((uintptr_t)buf)) == 0 && (0x03 & len) == 0) ioread32_rep(chip->IO_ADDR_R, buf, len >> 2); - else if ((0x01 & ((unsigned)buf)) == 0 && (0x01 & len) == 0) + else if ((0x01 & ((uintptr_t)buf)) == 0 && (0x01 & len) == 0) ioread16_rep(chip->IO_ADDR_R, buf, len >> 1); else ioread8_rep(chip->IO_ADDR_R, buf, len); @@ -454,9 +453,9 @@ static void nand_davinci_write_buf(struct mtd_info *mtd, { struct nand_chip *chip = mtd_to_nand(mtd); - if ((0x03 & ((unsigned)buf)) == 0 && (0x03 & len) == 0) + if ((0x03 & ((uintptr_t)buf)) == 0 && (0x03 & len) == 0) iowrite32_rep(chip->IO_ADDR_R, buf, len >> 2); - else if ((0x01 & ((unsigned)buf)) == 0 && (0x01 & len) == 0) + else if ((0x01 & ((uintptr_t)buf)) == 0 && (0x01 & len) == 0) iowrite16_rep(chip->IO_ADDR_R, buf, len >> 1); else iowrite8_rep(chip->IO_ADDR_R, buf, len); @@ -606,6 +605,104 @@ static struct davinci_nand_pdata } #endif +static int davinci_nand_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct davinci_nand_info *info = to_davinci_nand(mtd); + struct davinci_nand_pdata *pdata = nand_davinci_get_pdata(info->pdev); + int ret = 0; + + if (IS_ERR(pdata)) + return PTR_ERR(pdata); + + switch (info->chip.ecc.mode) { + case NAND_ECC_NONE: + pdata->ecc_bits = 0; + break; + case NAND_ECC_SOFT: + pdata->ecc_bits = 0; + /* + * This driver expects Hamming based ECC when ecc_mode is set + * to NAND_ECC_SOFT. Force ecc.algo to NAND_ECC_HAMMING to + * avoid adding an extra ->ecc_algo field to + * davinci_nand_pdata. + */ + info->chip.ecc.algo = NAND_ECC_HAMMING; + break; + case NAND_ECC_HW: + if (pdata->ecc_bits == 4) { + /* + * No sanity checks: CPUs must support this, + * and the chips may not use NAND_BUSWIDTH_16. + */ + + /* No sharing 4-bit hardware between chipselects yet */ + spin_lock_irq(&davinci_nand_lock); + if (ecc4_busy) + ret = -EBUSY; + else + ecc4_busy = true; + spin_unlock_irq(&davinci_nand_lock); + + if (ret == -EBUSY) + return ret; + + info->chip.ecc.calculate = nand_davinci_calculate_4bit; + info->chip.ecc.correct = nand_davinci_correct_4bit; + info->chip.ecc.hwctl = nand_davinci_hwctl_4bit; + info->chip.ecc.bytes = 10; + info->chip.ecc.options = NAND_ECC_GENERIC_ERASED_CHECK; + info->chip.ecc.algo = NAND_ECC_BCH; + } else { + /* 1bit ecc hamming */ + info->chip.ecc.calculate = nand_davinci_calculate_1bit; + info->chip.ecc.correct = nand_davinci_correct_1bit; + info->chip.ecc.hwctl = nand_davinci_hwctl_1bit; + info->chip.ecc.bytes = 3; + info->chip.ecc.algo = NAND_ECC_HAMMING; + } + info->chip.ecc.size = 512; + info->chip.ecc.strength = pdata->ecc_bits; + break; + default: + return -EINVAL; + } + + /* + * Update ECC layout if needed ... for 1-bit HW ECC, the default + * is OK, but it allocates 6 bytes when only 3 are needed (for + * each 512 bytes). For the 4-bit HW ECC, that default is not + * usable: 10 bytes are needed, not 6. + */ + if (pdata->ecc_bits == 4) { + int chunks = mtd->writesize / 512; + + if (!chunks || mtd->oobsize < 16) { + dev_dbg(&info->pdev->dev, "too small\n"); + return -EINVAL; + } + + /* For small page chips, preserve the manufacturer's + * badblock marking data ... and make sure a flash BBT + * table marker fits in the free bytes. + */ + if (chunks == 1) { + mtd_set_ooblayout(mtd, &hwecc4_small_ooblayout_ops); + } else if (chunks == 4 || chunks == 8) { + mtd_set_ooblayout(mtd, &nand_ooblayout_lp_ops); + info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST; + } else { + return -EIO; + } + } + + return ret; +} + +static const struct nand_controller_ops davinci_nand_controller_ops = { + .attach_chip = davinci_nand_attach_chip, +}; + static int nand_davinci_probe(struct platform_device *pdev) { struct davinci_nand_pdata *pdata; @@ -659,7 +756,7 @@ static int nand_davinci_probe(struct platform_device *pdev) return -EADDRNOTAVAIL; } - info->dev = &pdev->dev; + info->pdev = pdev; info->base = base; info->vaddr = vaddr; @@ -680,9 +777,7 @@ static int nand_davinci_probe(struct platform_device *pdev) info->chip.bbt_md = pdata->bbt_md; info->timing = pdata->timing; - info->ioaddr = (uint32_t __force) vaddr; - - info->current_cs = info->ioaddr; + info->current_cs = info->vaddr; info->core_chipsel = pdata->core_chipsel; info->mask_chipsel = pdata->mask_chipsel; @@ -711,100 +806,15 @@ static int nand_davinci_probe(struct platform_device *pdev) spin_unlock_irq(&davinci_nand_lock); /* Scan to find existence of the device(s) */ - ret = nand_scan_ident(mtd, pdata->mask_chipsel ? 2 : 1, NULL); + info->chip.dummy_controller.ops = &davinci_nand_controller_ops; + ret = nand_scan(mtd, pdata->mask_chipsel ? 2 : 1); if (ret < 0) { dev_dbg(&pdev->dev, "no NAND chip(s) found\n"); return ret; } - switch (info->chip.ecc.mode) { - case NAND_ECC_NONE: - pdata->ecc_bits = 0; - break; - case NAND_ECC_SOFT: - pdata->ecc_bits = 0; - /* - * This driver expects Hamming based ECC when ecc_mode is set - * to NAND_ECC_SOFT. Force ecc.algo to NAND_ECC_HAMMING to - * avoid adding an extra ->ecc_algo field to - * davinci_nand_pdata. - */ - info->chip.ecc.algo = NAND_ECC_HAMMING; - break; - case NAND_ECC_HW: - if (pdata->ecc_bits == 4) { - /* No sanity checks: CPUs must support this, - * and the chips may not use NAND_BUSWIDTH_16. - */ - - /* No sharing 4-bit hardware between chipselects yet */ - spin_lock_irq(&davinci_nand_lock); - if (ecc4_busy) - ret = -EBUSY; - else - ecc4_busy = true; - spin_unlock_irq(&davinci_nand_lock); - - if (ret == -EBUSY) - return ret; - - info->chip.ecc.calculate = nand_davinci_calculate_4bit; - info->chip.ecc.correct = nand_davinci_correct_4bit; - info->chip.ecc.hwctl = nand_davinci_hwctl_4bit; - info->chip.ecc.bytes = 10; - info->chip.ecc.options = NAND_ECC_GENERIC_ERASED_CHECK; - info->chip.ecc.algo = NAND_ECC_BCH; - } else { - /* 1bit ecc hamming */ - info->chip.ecc.calculate = nand_davinci_calculate_1bit; - info->chip.ecc.correct = nand_davinci_correct_1bit; - info->chip.ecc.hwctl = nand_davinci_hwctl_1bit; - info->chip.ecc.bytes = 3; - info->chip.ecc.algo = NAND_ECC_HAMMING; - } - info->chip.ecc.size = 512; - info->chip.ecc.strength = pdata->ecc_bits; - break; - default: - return -EINVAL; - } - - /* Update ECC layout if needed ... for 1-bit HW ECC, the default - * is OK, but it allocates 6 bytes when only 3 are needed (for - * each 512 bytes). For the 4-bit HW ECC, that default is not - * usable: 10 bytes are needed, not 6. - */ - if (pdata->ecc_bits == 4) { - int chunks = mtd->writesize / 512; - - if (!chunks || mtd->oobsize < 16) { - dev_dbg(&pdev->dev, "too small\n"); - ret = -EINVAL; - goto err; - } - - /* For small page chips, preserve the manufacturer's - * badblock marking data ... and make sure a flash BBT - * table marker fits in the free bytes. - */ - if (chunks == 1) { - mtd_set_ooblayout(mtd, &hwecc4_small_ooblayout_ops); - } else if (chunks == 4 || chunks == 8) { - mtd_set_ooblayout(mtd, &nand_ooblayout_lp_ops); - info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST; - } else { - ret = -EIO; - goto err; - } - } - - ret = nand_scan_tail(mtd); - if (ret < 0) - goto err; - if (pdata->parts) - ret = mtd_device_parse_register(mtd, NULL, NULL, - pdata->parts, pdata->nr_parts); + ret = mtd_device_register(mtd, pdata->parts, pdata->nr_parts); else ret = mtd_device_register(mtd, NULL, 0); if (ret < 0) @@ -819,11 +829,6 @@ static int nand_davinci_probe(struct platform_device *pdev) err_cleanup_nand: nand_cleanup(&info->chip); -err: - spin_lock_irq(&davinci_nand_lock); - if (info->chip.ecc.mode == NAND_ECC_HW_SYNDROME) - ecc4_busy = false; - spin_unlock_irq(&davinci_nand_lock); return ret; } diff --git a/drivers/mtd/nand/raw/denali.c b/drivers/mtd/nand/raw/denali.c index 2a302a1d1430..ca18612c4201 100644 --- a/drivers/mtd/nand/raw/denali.c +++ b/drivers/mtd/nand/raw/denali.c @@ -51,14 +51,6 @@ MODULE_LICENSE("GPL"); #define DENALI_INVALID_BANK -1 #define DENALI_NR_BANKS 4 -/* - * The bus interface clock, clk_x, is phase aligned with the core clock. The - * clk_x is an integral multiple N of the core clk. The value N is configured - * at IP delivery time, and its available value is 4, 5, or 6. We need to align - * to the largest value to make it work with any possible configuration. - */ -#define DENALI_CLK_X_MULT 6 - static inline struct denali_nand_info *mtd_to_denali(struct mtd_info *mtd) { return container_of(mtd_to_nand(mtd), struct denali_nand_info, nand); @@ -954,7 +946,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, { struct denali_nand_info *denali = mtd_to_denali(mtd); const struct nand_sdr_timings *timings; - unsigned long t_clk; + unsigned long t_x, mult_x; int acc_clks, re_2_we, re_2_re, we_2_re, addr_2_data; int rdwr_en_lo, rdwr_en_hi, rdwr_en_lo_hi, cs_setup; int addr_2_data_mask; @@ -965,15 +957,24 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, return PTR_ERR(timings); /* clk_x period in picoseconds */ - t_clk = DIV_ROUND_DOWN_ULL(1000000000000ULL, denali->clk_x_rate); - if (!t_clk) + t_x = DIV_ROUND_DOWN_ULL(1000000000000ULL, denali->clk_x_rate); + if (!t_x) + return -EINVAL; + + /* + * The bus interface clock, clk_x, is phase aligned with the core clock. + * The clk_x is an integral multiple N of the core clk. The value N is + * configured at IP delivery time, and its available value is 4, 5, 6. + */ + mult_x = DIV_ROUND_CLOSEST_ULL(denali->clk_x_rate, denali->clk_rate); + if (mult_x < 4 || mult_x > 6) return -EINVAL; if (chipnr == NAND_DATA_IFACE_CHECK_ONLY) return 0; /* tREA -> ACC_CLKS */ - acc_clks = DIV_ROUND_UP(timings->tREA_max, t_clk); + acc_clks = DIV_ROUND_UP(timings->tREA_max, t_x); acc_clks = min_t(int, acc_clks, ACC_CLKS__VALUE); tmp = ioread32(denali->reg + ACC_CLKS); @@ -982,7 +983,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, iowrite32(tmp, denali->reg + ACC_CLKS); /* tRWH -> RE_2_WE */ - re_2_we = DIV_ROUND_UP(timings->tRHW_min, t_clk); + re_2_we = DIV_ROUND_UP(timings->tRHW_min, t_x); re_2_we = min_t(int, re_2_we, RE_2_WE__VALUE); tmp = ioread32(denali->reg + RE_2_WE); @@ -991,7 +992,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, iowrite32(tmp, denali->reg + RE_2_WE); /* tRHZ -> RE_2_RE */ - re_2_re = DIV_ROUND_UP(timings->tRHZ_max, t_clk); + re_2_re = DIV_ROUND_UP(timings->tRHZ_max, t_x); re_2_re = min_t(int, re_2_re, RE_2_RE__VALUE); tmp = ioread32(denali->reg + RE_2_RE); @@ -1005,8 +1006,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, * With WE_2_RE properly set, the Denali controller automatically takes * care of the delay; the driver need not set NAND_WAIT_TCCS. */ - we_2_re = DIV_ROUND_UP(max(timings->tCCS_min, timings->tWHR_min), - t_clk); + we_2_re = DIV_ROUND_UP(max(timings->tCCS_min, timings->tWHR_min), t_x); we_2_re = min_t(int, we_2_re, TWHR2_AND_WE_2_RE__WE_2_RE); tmp = ioread32(denali->reg + TWHR2_AND_WE_2_RE); @@ -1021,7 +1021,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, if (denali->revision < 0x0501) addr_2_data_mask >>= 1; - addr_2_data = DIV_ROUND_UP(timings->tADL_min, t_clk); + addr_2_data = DIV_ROUND_UP(timings->tADL_min, t_x); addr_2_data = min_t(int, addr_2_data, addr_2_data_mask); tmp = ioread32(denali->reg + TCWAW_AND_ADDR_2_DATA); @@ -1031,7 +1031,7 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, /* tREH, tWH -> RDWR_EN_HI_CNT */ rdwr_en_hi = DIV_ROUND_UP(max(timings->tREH_min, timings->tWH_min), - t_clk); + t_x); rdwr_en_hi = min_t(int, rdwr_en_hi, RDWR_EN_HI_CNT__VALUE); tmp = ioread32(denali->reg + RDWR_EN_HI_CNT); @@ -1040,11 +1040,10 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, iowrite32(tmp, denali->reg + RDWR_EN_HI_CNT); /* tRP, tWP -> RDWR_EN_LO_CNT */ - rdwr_en_lo = DIV_ROUND_UP(max(timings->tRP_min, timings->tWP_min), - t_clk); + rdwr_en_lo = DIV_ROUND_UP(max(timings->tRP_min, timings->tWP_min), t_x); rdwr_en_lo_hi = DIV_ROUND_UP(max(timings->tRC_min, timings->tWC_min), - t_clk); - rdwr_en_lo_hi = max(rdwr_en_lo_hi, DENALI_CLK_X_MULT); + t_x); + rdwr_en_lo_hi = max_t(int, rdwr_en_lo_hi, mult_x); rdwr_en_lo = max(rdwr_en_lo, rdwr_en_lo_hi - rdwr_en_hi); rdwr_en_lo = min_t(int, rdwr_en_lo, RDWR_EN_LO_CNT__VALUE); @@ -1054,8 +1053,8 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, iowrite32(tmp, denali->reg + RDWR_EN_LO_CNT); /* tCS, tCEA -> CS_SETUP_CNT */ - cs_setup = max3((int)DIV_ROUND_UP(timings->tCS_min, t_clk) - rdwr_en_lo, - (int)DIV_ROUND_UP(timings->tCEA_max, t_clk) - acc_clks, + cs_setup = max3((int)DIV_ROUND_UP(timings->tCS_min, t_x) - rdwr_en_lo, + (int)DIV_ROUND_UP(timings->tCEA_max, t_x) - acc_clks, 0); cs_setup = min_t(int, cs_setup, CS_SETUP_CNT__VALUE); @@ -1120,33 +1119,6 @@ int denali_calc_ecc_bytes(int step_size, int strength) } EXPORT_SYMBOL(denali_calc_ecc_bytes); -static int denali_ecc_setup(struct mtd_info *mtd, struct nand_chip *chip, - struct denali_nand_info *denali) -{ - int oobavail = mtd->oobsize - denali->oob_skip_bytes; - int ret; - - /* - * If .size and .strength are already set (usually by DT), - * check if they are supported by this controller. - */ - if (chip->ecc.size && chip->ecc.strength) - return nand_check_ecc_caps(chip, denali->ecc_caps, oobavail); - - /* - * We want .size and .strength closest to the chip's requirement - * unless NAND_ECC_MAXIMIZE is requested. - */ - if (!(chip->ecc.options & NAND_ECC_MAXIMIZE)) { - ret = nand_match_ecc_req(chip, denali->ecc_caps, oobavail); - if (!ret) - return 0; - } - - /* Max ECC strength is the last thing we can do */ - return nand_maximize_ecc(chip, denali->ecc_caps, oobavail); -} - static int denali_ooblayout_ecc(struct mtd_info *mtd, int section, struct mtd_oob_region *oobregion) { @@ -1233,62 +1205,12 @@ static int denali_multidev_fixup(struct denali_nand_info *denali) return 0; } -int denali_init(struct denali_nand_info *denali) +static int denali_attach_chip(struct nand_chip *chip) { - struct nand_chip *chip = &denali->nand; struct mtd_info *mtd = nand_to_mtd(chip); - u32 features = ioread32(denali->reg + FEATURES); + struct denali_nand_info *denali = mtd_to_denali(mtd); int ret; - mtd->dev.parent = denali->dev; - denali_hw_init(denali); - - init_completion(&denali->complete); - spin_lock_init(&denali->irq_lock); - - denali_clear_irq_all(denali); - - ret = devm_request_irq(denali->dev, denali->irq, denali_isr, - IRQF_SHARED, DENALI_NAND_NAME, denali); - if (ret) { - dev_err(denali->dev, "Unable to request IRQ\n"); - return ret; - } - - denali_enable_irq(denali); - denali_reset_banks(denali); - - denali->active_bank = DENALI_INVALID_BANK; - - nand_set_flash_node(chip, denali->dev->of_node); - /* Fallback to the default name if DT did not give "label" property */ - if (!mtd->name) - mtd->name = "denali-nand"; - - chip->select_chip = denali_select_chip; - chip->read_byte = denali_read_byte; - chip->write_byte = denali_write_byte; - chip->read_word = denali_read_word; - chip->cmd_ctrl = denali_cmd_ctrl; - chip->dev_ready = denali_dev_ready; - chip->waitfunc = denali_waitfunc; - - if (features & FEATURES__INDEX_ADDR) { - denali->host_read = denali_indexed_read; - denali->host_write = denali_indexed_write; - } else { - denali->host_read = denali_direct_read; - denali->host_write = denali_direct_write; - } - - /* clk rate info is needed for setup_data_interface */ - if (denali->clk_x_rate) - chip->setup_data_interface = denali_setup_data_interface; - - ret = nand_scan_ident(mtd, denali->max_banks, NULL); - if (ret) - goto disable_irq; - if (ioread32(denali->reg + FEATURES) & FEATURES__DMA) denali->dma_avail = 1; @@ -1317,10 +1239,11 @@ int denali_init(struct denali_nand_info *denali) chip->ecc.mode = NAND_ECC_HW_SYNDROME; chip->options |= NAND_NO_SUBPAGE_WRITE; - ret = denali_ecc_setup(mtd, chip, denali); + ret = nand_ecc_choose_conf(chip, denali->ecc_caps, + mtd->oobsize - denali->oob_skip_bytes); if (ret) { dev_err(denali->dev, "Failed to setup ECC settings.\n"); - goto disable_irq; + return ret; } dev_dbg(denali->dev, @@ -1364,7 +1287,7 @@ int denali_init(struct denali_nand_info *denali) ret = denali_multidev_fixup(denali); if (ret) - goto disable_irq; + return ret; /* * This buffer is DMA-mapped by denali_{read,write}_page_raw. Do not @@ -1372,26 +1295,92 @@ int denali_init(struct denali_nand_info *denali) * guarantee DMA-safe alignment. */ denali->buf = kmalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL); - if (!denali->buf) { - ret = -ENOMEM; - goto disable_irq; + if (!denali->buf) + return -ENOMEM; + + return 0; +} + +static void denali_detach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct denali_nand_info *denali = mtd_to_denali(mtd); + + kfree(denali->buf); +} + +static const struct nand_controller_ops denali_controller_ops = { + .attach_chip = denali_attach_chip, + .detach_chip = denali_detach_chip, +}; + +int denali_init(struct denali_nand_info *denali) +{ + struct nand_chip *chip = &denali->nand; + struct mtd_info *mtd = nand_to_mtd(chip); + u32 features = ioread32(denali->reg + FEATURES); + int ret; + + mtd->dev.parent = denali->dev; + denali_hw_init(denali); + + init_completion(&denali->complete); + spin_lock_init(&denali->irq_lock); + + denali_clear_irq_all(denali); + + ret = devm_request_irq(denali->dev, denali->irq, denali_isr, + IRQF_SHARED, DENALI_NAND_NAME, denali); + if (ret) { + dev_err(denali->dev, "Unable to request IRQ\n"); + return ret; } - ret = nand_scan_tail(mtd); + denali_enable_irq(denali); + denali_reset_banks(denali); + + denali->active_bank = DENALI_INVALID_BANK; + + nand_set_flash_node(chip, denali->dev->of_node); + /* Fallback to the default name if DT did not give "label" property */ + if (!mtd->name) + mtd->name = "denali-nand"; + + chip->select_chip = denali_select_chip; + chip->read_byte = denali_read_byte; + chip->write_byte = denali_write_byte; + chip->read_word = denali_read_word; + chip->cmd_ctrl = denali_cmd_ctrl; + chip->dev_ready = denali_dev_ready; + chip->waitfunc = denali_waitfunc; + + if (features & FEATURES__INDEX_ADDR) { + denali->host_read = denali_indexed_read; + denali->host_write = denali_indexed_write; + } else { + denali->host_read = denali_direct_read; + denali->host_write = denali_direct_write; + } + + /* clk rate info is needed for setup_data_interface */ + if (denali->clk_rate && denali->clk_x_rate) + chip->setup_data_interface = denali_setup_data_interface; + + chip->dummy_controller.ops = &denali_controller_ops; + ret = nand_scan(mtd, denali->max_banks); if (ret) - goto free_buf; + goto disable_irq; ret = mtd_device_register(mtd, NULL, 0); if (ret) { dev_err(denali->dev, "Failed to register MTD: %d\n", ret); goto cleanup_nand; } + return 0; cleanup_nand: nand_cleanup(chip); -free_buf: - kfree(denali->buf); disable_irq: denali_disable_irq(denali); @@ -1404,7 +1393,6 @@ void denali_remove(struct denali_nand_info *denali) struct mtd_info *mtd = nand_to_mtd(&denali->nand); nand_release(mtd); - kfree(denali->buf); denali_disable_irq(denali); } EXPORT_SYMBOL(denali_remove); diff --git a/drivers/mtd/nand/raw/denali.h b/drivers/mtd/nand/raw/denali.h index 9ad33d237378..1f8feaf924eb 100644 --- a/drivers/mtd/nand/raw/denali.h +++ b/drivers/mtd/nand/raw/denali.h @@ -300,6 +300,7 @@ struct denali_nand_info { struct nand_chip nand; + unsigned long clk_rate; /* core clock rate */ unsigned long clk_x_rate; /* bus interface clock rate */ int active_bank; /* currently selected bank */ struct device *dev; diff --git a/drivers/mtd/nand/raw/denali_dt.c b/drivers/mtd/nand/raw/denali_dt.c index 5869e90cc14b..0faaad032e5f 100644 --- a/drivers/mtd/nand/raw/denali_dt.c +++ b/drivers/mtd/nand/raw/denali_dt.c @@ -27,7 +27,9 @@ struct denali_dt { struct denali_nand_info denali; - struct clk *clk; + struct clk *clk; /* core clock */ + struct clk *clk_x; /* bus interface clock */ + struct clk *clk_ecc; /* ECC circuit clock */ }; struct denali_dt_data { @@ -79,63 +81,99 @@ MODULE_DEVICE_TABLE(of, denali_nand_dt_ids); static int denali_dt_probe(struct platform_device *pdev) { + struct device *dev = &pdev->dev; struct resource *res; struct denali_dt *dt; const struct denali_dt_data *data; struct denali_nand_info *denali; int ret; - dt = devm_kzalloc(&pdev->dev, sizeof(*dt), GFP_KERNEL); + dt = devm_kzalloc(dev, sizeof(*dt), GFP_KERNEL); if (!dt) return -ENOMEM; denali = &dt->denali; - data = of_device_get_match_data(&pdev->dev); + data = of_device_get_match_data(dev); if (data) { denali->revision = data->revision; denali->caps = data->caps; denali->ecc_caps = data->ecc_caps; } - denali->dev = &pdev->dev; + denali->dev = dev; denali->irq = platform_get_irq(pdev, 0); if (denali->irq < 0) { - dev_err(&pdev->dev, "no irq defined\n"); + dev_err(dev, "no irq defined\n"); return denali->irq; } res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "denali_reg"); - denali->reg = devm_ioremap_resource(&pdev->dev, res); + denali->reg = devm_ioremap_resource(dev, res); if (IS_ERR(denali->reg)) return PTR_ERR(denali->reg); res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nand_data"); - denali->host = devm_ioremap_resource(&pdev->dev, res); + denali->host = devm_ioremap_resource(dev, res); if (IS_ERR(denali->host)) return PTR_ERR(denali->host); - dt->clk = devm_clk_get(&pdev->dev, NULL); + /* + * A single anonymous clock is supported for the backward compatibility. + * New platforms should support all the named clocks. + */ + dt->clk = devm_clk_get(dev, "nand"); + if (IS_ERR(dt->clk)) + dt->clk = devm_clk_get(dev, NULL); if (IS_ERR(dt->clk)) { - dev_err(&pdev->dev, "no clk available\n"); + dev_err(dev, "no clk available\n"); return PTR_ERR(dt->clk); } + + dt->clk_x = devm_clk_get(dev, "nand_x"); + if (IS_ERR(dt->clk_x)) + dt->clk_x = NULL; + + dt->clk_ecc = devm_clk_get(dev, "ecc"); + if (IS_ERR(dt->clk_ecc)) + dt->clk_ecc = NULL; + ret = clk_prepare_enable(dt->clk); if (ret) return ret; - /* - * Hardcode the clock rate for the backward compatibility. - * This works for both SOCFPGA and UniPhier. - */ - denali->clk_x_rate = 200000000; + ret = clk_prepare_enable(dt->clk_x); + if (ret) + goto out_disable_clk; + + ret = clk_prepare_enable(dt->clk_ecc); + if (ret) + goto out_disable_clk_x; + + if (dt->clk_x) { + denali->clk_rate = clk_get_rate(dt->clk); + denali->clk_x_rate = clk_get_rate(dt->clk_x); + } else { + /* + * Hardcode the clock rates for the backward compatibility. + * This works for both SOCFPGA and UniPhier. + */ + dev_notice(dev, + "necessary clock is missing. default clock rates are used.\n"); + denali->clk_rate = 50000000; + denali->clk_x_rate = 200000000; + } ret = denali_init(denali); if (ret) - goto out_disable_clk; + goto out_disable_clk_ecc; platform_set_drvdata(pdev, dt); return 0; +out_disable_clk_ecc: + clk_disable_unprepare(dt->clk_ecc); +out_disable_clk_x: + clk_disable_unprepare(dt->clk_x); out_disable_clk: clk_disable_unprepare(dt->clk); @@ -147,6 +185,8 @@ static int denali_dt_remove(struct platform_device *pdev) struct denali_dt *dt = platform_get_drvdata(pdev); denali_remove(&dt->denali); + clk_disable_unprepare(dt->clk_ecc); + clk_disable_unprepare(dt->clk_x); clk_disable_unprepare(dt->clk); return 0; diff --git a/drivers/mtd/nand/raw/denali_pci.c b/drivers/mtd/nand/raw/denali_pci.c index 49cb3e1f8bd0..7c8efc4c7bdf 100644 --- a/drivers/mtd/nand/raw/denali_pci.c +++ b/drivers/mtd/nand/raw/denali_pci.c @@ -73,6 +73,7 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id) denali->irq = dev->irq; denali->ecc_caps = &denali_pci_ecc_caps; denali->nand.ecc.options |= NAND_ECC_MAXIMIZE; + denali->clk_rate = 50000000; /* 50 MHz */ denali->clk_x_rate = 200000000; /* 200 MHz */ ret = pci_request_regions(dev, DENALI_NAND_NAME); diff --git a/drivers/mtd/nand/raw/diskonchip.c b/drivers/mtd/nand/raw/diskonchip.c index 8d10061abb4b..3c46188dd6d2 100644 --- a/drivers/mtd/nand/raw/diskonchip.c +++ b/drivers/mtd/nand/raw/diskonchip.c @@ -1291,7 +1291,7 @@ static int __init nftl_scan_bbt(struct mtd_info *mtd) this->bbt_md = NULL; } - ret = this->scan_bbt(mtd); + ret = nand_create_bbt(this); if (ret) return ret; @@ -1338,7 +1338,7 @@ static int __init inftl_scan_bbt(struct mtd_info *mtd) this->bbt_md->pattern = "TBB_SYSM"; } - ret = this->scan_bbt(mtd); + ret = nand_create_bbt(this); if (ret) return ret; diff --git a/drivers/mtd/nand/raw/docg4.c b/drivers/mtd/nand/raw/docg4.c index 1314aa99b9ab..a3f04315c05c 100644 --- a/drivers/mtd/nand/raw/docg4.c +++ b/drivers/mtd/nand/raw/docg4.c @@ -1227,10 +1227,9 @@ static void __init init_mtd_structs(struct mtd_info *mtd) * required within a nand driver because they are performed by the nand * infrastructure code as part of nand_scan(). In this case they need * to be initialized here because we skip call to nand_scan_ident() (the - * first half of nand_scan()). The call to nand_scan_ident() is skipped - * because for this device the chip id is not read in the manner of a - * standard nand device. Unfortunately, nand_scan_ident() does other - * things as well, such as call nand_set_defaults(). + * first half of nand_scan()). The call to nand_scan_ident() could be + * skipped because for this device the chip id is not read in the manner + * of a standard nand device. */ struct nand_chip *nand = mtd_to_nand(mtd); @@ -1257,8 +1256,8 @@ static void __init init_mtd_structs(struct mtd_info *mtd) nand->ecc.strength = DOCG4_T; nand->options = NAND_BUSWIDTH_16 | NAND_NO_SUBPAGE_WRITE; nand->IO_ADDR_R = nand->IO_ADDR_W = doc->virtadr + DOC_IOSPACE_DATA; - nand->controller = &nand->hwcontrol; - nand_hw_control_init(nand->controller); + nand->controller = &nand->dummy_controller; + nand_controller_init(nand->controller); /* methods */ nand->cmdfunc = docg4_command; @@ -1315,6 +1314,40 @@ static int __init read_id_reg(struct mtd_info *mtd) static char const *part_probes[] = { "cmdlinepart", "saftlpart", NULL }; +static int docg4_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct docg4_priv *doc = (struct docg4_priv *)(chip + 1); + int ret; + + init_mtd_structs(mtd); + + /* Initialize kernel BCH algorithm */ + doc->bch = init_bch(DOCG4_M, DOCG4_T, DOCG4_PRIMITIVE_POLY); + if (!doc->bch) + return -EINVAL; + + reset(mtd); + + ret = read_id_reg(mtd); + if (ret) + free_bch(doc->bch); + + return ret; +} + +static void docg4_detach_chip(struct nand_chip *chip) +{ + struct docg4_priv *doc = (struct docg4_priv *)(chip + 1); + + free_bch(doc->bch); +} + +static const struct nand_controller_ops docg4_controller_ops = { + .attach_chip = docg4_attach_chip, + .detach_chip = docg4_detach_chip, +}; + static int __init probe_docg4(struct platform_device *pdev) { struct mtd_info *mtd; @@ -1341,7 +1374,7 @@ static int __init probe_docg4(struct platform_device *pdev) nand = kzalloc(len, GFP_KERNEL); if (nand == NULL) { retval = -ENOMEM; - goto fail_unmap; + goto unmap; } mtd = nand_to_mtd(nand); @@ -1350,46 +1383,35 @@ static int __init probe_docg4(struct platform_device *pdev) mtd->dev.parent = &pdev->dev; doc->virtadr = virtadr; doc->dev = dev; - - init_mtd_structs(mtd); - - /* initialize kernel bch algorithm */ - doc->bch = init_bch(DOCG4_M, DOCG4_T, DOCG4_PRIMITIVE_POLY); - if (doc->bch == NULL) { - retval = -EINVAL; - goto fail; - } - platform_set_drvdata(pdev, doc); - reset(mtd); - retval = read_id_reg(mtd); - if (retval == -ENODEV) { - dev_warn(dev, "No diskonchip G4 device found.\n"); - goto fail; - } - - retval = nand_scan_tail(mtd); + /* + * Running nand_scan() with maxchips == 0 will skip nand_scan_ident(), + * which is a specific operation with this driver and done in the + * ->attach_chip callback. + */ + nand->dummy_controller.ops = &docg4_controller_ops; + retval = nand_scan(mtd, 0); if (retval) - goto fail; + goto free_nand; retval = read_factory_bbt(mtd); if (retval) - goto fail; + goto cleanup_nand; retval = mtd_device_parse_register(mtd, part_probes, NULL, NULL, 0); if (retval) - goto fail; + goto cleanup_nand; doc->mtd = mtd; + return 0; -fail: - nand_release(mtd); /* deletes partitions and mtd devices */ - free_bch(doc->bch); +cleanup_nand: + nand_cleanup(nand); +free_nand: kfree(nand); - -fail_unmap: +unmap: iounmap(virtadr); return retval; @@ -1399,7 +1421,6 @@ static int __exit cleanup_docg4(struct platform_device *pdev) { struct docg4_priv *doc = platform_get_drvdata(pdev); nand_release(doc->mtd); - free_bch(doc->bch); kfree(mtd_to_nand(doc->mtd)); iounmap(doc->virtadr); return 0; diff --git a/drivers/mtd/nand/raw/fsl_elbc_nand.c b/drivers/mtd/nand/raw/fsl_elbc_nand.c index 51f0b340bc0d..55f449b711fd 100644 --- a/drivers/mtd/nand/raw/fsl_elbc_nand.c +++ b/drivers/mtd/nand/raw/fsl_elbc_nand.c @@ -61,7 +61,7 @@ struct fsl_elbc_mtd { /* Freescale eLBC FCM controller information */ struct fsl_elbc_fcm_ctrl { - struct nand_hw_control controller; + struct nand_controller controller; struct fsl_elbc_mtd *chips[MAX_BANKS]; u8 __iomem *addr; /* Address of assigned FCM buffer */ @@ -637,9 +637,9 @@ static int fsl_elbc_wait(struct mtd_info *mtd, struct nand_chip *chip) return (elbc_fcm_ctrl->mdr & 0xff) | NAND_STATUS_WP; } -static int fsl_elbc_chip_init_tail(struct mtd_info *mtd) +static int fsl_elbc_attach_chip(struct nand_chip *chip) { - struct nand_chip *chip = mtd_to_nand(mtd); + struct mtd_info *mtd = nand_to_mtd(chip); struct fsl_elbc_mtd *priv = nand_get_controller_data(chip); struct fsl_lbc_ctrl *ctrl = priv->ctrl; struct fsl_lbc_regs __iomem *lbc = ctrl->regs; @@ -700,12 +700,16 @@ static int fsl_elbc_chip_init_tail(struct mtd_info *mtd) dev_err(priv->dev, "fsl_elbc_init: page size %d is not supported\n", mtd->writesize); - return -1; + return -ENOTSUPP; } return 0; } +static const struct nand_controller_ops fsl_elbc_controller_ops = { + .attach_chip = fsl_elbc_attach_chip, +}; + static int fsl_elbc_read_page(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { @@ -879,7 +883,7 @@ static int fsl_elbc_nand_probe(struct platform_device *pdev) } elbc_fcm_ctrl->counter++; - nand_hw_control_init(&elbc_fcm_ctrl->controller); + nand_controller_init(&elbc_fcm_ctrl->controller); fsl_lbc_ctrl_dev->nand = elbc_fcm_ctrl; } else { elbc_fcm_ctrl = fsl_lbc_ctrl_dev->nand; @@ -910,15 +914,8 @@ static int fsl_elbc_nand_probe(struct platform_device *pdev) if (ret) goto err; - ret = nand_scan_ident(mtd, 1, NULL); - if (ret) - goto err; - - ret = fsl_elbc_chip_init_tail(mtd); - if (ret) - goto err; - - ret = nand_scan_tail(mtd); + priv->chip.controller->ops = &fsl_elbc_controller_ops; + ret = nand_scan(mtd, 1); if (ret) goto err; diff --git a/drivers/mtd/nand/raw/fsl_ifc_nand.c b/drivers/mtd/nand/raw/fsl_ifc_nand.c index 382b67e97174..24f59d0066af 100644 --- a/drivers/mtd/nand/raw/fsl_ifc_nand.c +++ b/drivers/mtd/nand/raw/fsl_ifc_nand.c @@ -51,7 +51,7 @@ struct fsl_ifc_mtd { /* overview of the fsl ifc controller */ struct fsl_ifc_nand_ctrl { - struct nand_hw_control controller; + struct nand_controller controller; struct fsl_ifc_mtd *chips[FSL_IFC_BANK_COUNT]; void __iomem *addr; /* Address of assigned IFC buffer */ @@ -225,7 +225,7 @@ static void fsl_ifc_run_command(struct mtd_info *mtd) int bufnum = nctrl->page & priv->bufnum_mask; int sector_start = bufnum * chip->ecc.steps; int sector_end = sector_start + chip->ecc.steps - 1; - __be32 *eccstat_regs; + __be32 __iomem *eccstat_regs; eccstat_regs = ifc->ifc_nand.nand_eccstat; eccstat = ifc_in32(&eccstat_regs[sector_start / 4]); @@ -714,9 +714,9 @@ static int fsl_ifc_write_page(struct mtd_info *mtd, struct nand_chip *chip, return nand_prog_page_end_op(chip); } -static int fsl_ifc_chip_init_tail(struct mtd_info *mtd) +static int fsl_ifc_attach_chip(struct nand_chip *chip) { - struct nand_chip *chip = mtd_to_nand(mtd); + struct mtd_info *mtd = nand_to_mtd(chip); struct fsl_ifc_mtd *priv = nand_get_controller_data(chip); dev_dbg(priv->dev, "%s: nand->numchips = %d\n", __func__, @@ -757,6 +757,10 @@ static int fsl_ifc_chip_init_tail(struct mtd_info *mtd) return 0; } +static const struct nand_controller_ops fsl_ifc_controller_ops = { + .attach_chip = fsl_ifc_attach_chip, +}; + static void fsl_ifc_sram_init(struct fsl_ifc_mtd *priv) { struct fsl_ifc_ctrl *ctrl = priv->ctrl; @@ -1004,7 +1008,7 @@ static int fsl_ifc_nand_probe(struct platform_device *dev) ifc_nand_ctrl->addr = NULL; fsl_ifc_ctrl_dev->nand = ifc_nand_ctrl; - nand_hw_control_init(&ifc_nand_ctrl->controller); + nand_controller_init(&ifc_nand_ctrl->controller); } else { ifc_nand_ctrl = fsl_ifc_ctrl_dev->nand; } @@ -1046,15 +1050,8 @@ static int fsl_ifc_nand_probe(struct platform_device *dev) if (ret) goto err; - ret = nand_scan_ident(mtd, 1, NULL); - if (ret) - goto err; - - ret = fsl_ifc_chip_init_tail(mtd); - if (ret) - goto err; - - ret = nand_scan_tail(mtd); + priv->chip.controller->ops = &fsl_ifc_controller_ops; + ret = nand_scan(mtd, 1); if (ret) goto err; diff --git a/drivers/mtd/nand/raw/fsmc_nand.c b/drivers/mtd/nand/raw/fsmc_nand.c index f4a5a317d4ae..f418236fa020 100644 --- a/drivers/mtd/nand/raw/fsmc_nand.c +++ b/drivers/mtd/nand/raw/fsmc_nand.c @@ -62,7 +62,7 @@ reg) /* fsmc controller registers for NAND flash */ -#define PC 0x00 +#define FSMC_PC 0x00 /* pc register definitions */ #define FSMC_RESET (1 << 0) #define FSMC_WAITON (1 << 1) @@ -273,12 +273,13 @@ static void fsmc_nand_setup(struct fsmc_nand_data *host, tset = (tims->tset & FSMC_TSET_MASK) << FSMC_TSET_SHIFT; if (host->nand.options & NAND_BUSWIDTH_16) - writel_relaxed(value | FSMC_DEVWID_16, host->regs_va + PC); + writel_relaxed(value | FSMC_DEVWID_16, + host->regs_va + FSMC_PC); else - writel_relaxed(value | FSMC_DEVWID_8, host->regs_va + PC); + writel_relaxed(value | FSMC_DEVWID_8, host->regs_va + FSMC_PC); - writel_relaxed(readl(host->regs_va + PC) | tclr | tar, - host->regs_va + PC); + writel_relaxed(readl(host->regs_va + FSMC_PC) | tclr | tar, + host->regs_va + FSMC_PC); writel_relaxed(thiz | thold | twait | tset, host->regs_va + COMM); writel_relaxed(thiz | thold | twait | tset, host->regs_va + ATTRIB); } @@ -371,12 +372,12 @@ static void fsmc_enable_hwecc(struct mtd_info *mtd, int mode) { struct fsmc_nand_data *host = mtd_to_fsmc(mtd); - writel_relaxed(readl(host->regs_va + PC) & ~FSMC_ECCPLEN_256, - host->regs_va + PC); - writel_relaxed(readl(host->regs_va + PC) & ~FSMC_ECCEN, - host->regs_va + PC); - writel_relaxed(readl(host->regs_va + PC) | FSMC_ECCEN, - host->regs_va + PC); + writel_relaxed(readl(host->regs_va + FSMC_PC) & ~FSMC_ECCPLEN_256, + host->regs_va + FSMC_PC); + writel_relaxed(readl(host->regs_va + FSMC_PC) & ~FSMC_ECCEN, + host->regs_va + FSMC_PC); + writel_relaxed(readl(host->regs_va + FSMC_PC) | FSMC_ECCEN, + host->regs_va + FSMC_PC); } /* @@ -546,7 +547,7 @@ static void fsmc_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) struct fsmc_nand_data *host = mtd_to_fsmc(mtd); int i; - if (IS_ALIGNED((uint32_t)buf, sizeof(uint32_t)) && + if (IS_ALIGNED((uintptr_t)buf, sizeof(uint32_t)) && IS_ALIGNED(len, sizeof(uint32_t))) { uint32_t *p = (uint32_t *)buf; len = len >> 2; @@ -569,7 +570,7 @@ static void fsmc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) struct fsmc_nand_data *host = mtd_to_fsmc(mtd); int i; - if (IS_ALIGNED((uint32_t)buf, sizeof(uint32_t)) && + if (IS_ALIGNED((uintptr_t)buf, sizeof(uint32_t)) && IS_ALIGNED(len, sizeof(uint32_t))) { uint32_t *p = (uint32_t *)buf; len = len >> 2; @@ -618,11 +619,11 @@ static void fsmc_select_chip(struct mtd_info *mtd, int chipnr) if (chipnr > 0) return; - pc = readl(host->regs_va + PC); + pc = readl(host->regs_va + FSMC_PC); if (chipnr < 0) - writel_relaxed(pc & ~FSMC_ENABLE, host->regs_va + PC); + writel_relaxed(pc & ~FSMC_ENABLE, host->regs_va + FSMC_PC); else - writel_relaxed(pc | FSMC_ENABLE, host->regs_va + PC); + writel_relaxed(pc | FSMC_ENABLE, host->regs_va + FSMC_PC); /* nCE line must be asserted before starting any operation */ mb(); @@ -740,7 +741,7 @@ static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, for (i = 0, s = 0; s < eccsteps; s++, i += eccbytes, p += eccsize) { nand_read_page_op(chip, page, s * eccsize, NULL, 0); chip->ecc.hwctl(mtd, NAND_ECC_READ); - chip->read_buf(mtd, p, eccsize); + nand_read_data_op(chip, p, eccsize, false); for (j = 0; j < eccbytes;) { struct mtd_oob_region oobregion; @@ -918,6 +919,82 @@ static int fsmc_nand_probe_config_dt(struct platform_device *pdev, return 0; } +static int fsmc_nand_attach_chip(struct nand_chip *nand) +{ + struct mtd_info *mtd = nand_to_mtd(nand); + struct fsmc_nand_data *host = mtd_to_fsmc(mtd); + + if (AMBA_REV_BITS(host->pid) >= 8) { + switch (mtd->oobsize) { + case 16: + case 64: + case 128: + case 224: + case 256: + break; + default: + dev_warn(host->dev, + "No oob scheme defined for oobsize %d\n", + mtd->oobsize); + return -EINVAL; + } + + mtd_set_ooblayout(mtd, &fsmc_ecc4_ooblayout_ops); + + return 0; + } + + switch (nand->ecc.mode) { + case NAND_ECC_HW: + dev_info(host->dev, "Using 1-bit HW ECC scheme\n"); + nand->ecc.calculate = fsmc_read_hwecc_ecc1; + nand->ecc.correct = nand_correct_data; + nand->ecc.bytes = 3; + nand->ecc.strength = 1; + break; + + case NAND_ECC_SOFT: + if (nand->ecc.algo == NAND_ECC_BCH) { + dev_info(host->dev, + "Using 4-bit SW BCH ECC scheme\n"); + break; + } + + case NAND_ECC_ON_DIE: + break; + + default: + dev_err(host->dev, "Unsupported ECC mode!\n"); + return -ENOTSUPP; + } + + /* + * Don't set layout for BCH4 SW ECC. This will be + * generated later in nand_bch_init() later. + */ + if (nand->ecc.mode == NAND_ECC_HW) { + switch (mtd->oobsize) { + case 16: + case 64: + case 128: + mtd_set_ooblayout(mtd, + &fsmc_ecc1_ooblayout_ops); + break; + default: + dev_warn(host->dev, + "No oob scheme defined for oobsize %d\n", + mtd->oobsize); + return -EINVAL; + } + } + + return 0; +} + +static const struct nand_controller_ops fsmc_nand_controller_ops = { + .attach_chip = fsmc_nand_attach_chip, +}; + /* * fsmc_nand_probe - Probe function * @pdev: platform device structure @@ -1047,76 +1124,8 @@ static int __init fsmc_nand_probe(struct platform_device *pdev) /* * Scan to find existence of the device */ - ret = nand_scan_ident(mtd, 1, NULL); - if (ret) { - dev_err(&pdev->dev, "No NAND Device found!\n"); - goto release_dma_write_chan; - } - - if (AMBA_REV_BITS(host->pid) >= 8) { - switch (mtd->oobsize) { - case 16: - case 64: - case 128: - case 224: - case 256: - break; - default: - dev_warn(&pdev->dev, "No oob scheme defined for oobsize %d\n", - mtd->oobsize); - ret = -EINVAL; - goto release_dma_write_chan; - } - - mtd_set_ooblayout(mtd, &fsmc_ecc4_ooblayout_ops); - } else { - switch (nand->ecc.mode) { - case NAND_ECC_HW: - dev_info(&pdev->dev, "Using 1-bit HW ECC scheme\n"); - nand->ecc.calculate = fsmc_read_hwecc_ecc1; - nand->ecc.correct = nand_correct_data; - nand->ecc.bytes = 3; - nand->ecc.strength = 1; - break; - - case NAND_ECC_SOFT: - if (nand->ecc.algo == NAND_ECC_BCH) { - dev_info(&pdev->dev, "Using 4-bit SW BCH ECC scheme\n"); - break; - } - - case NAND_ECC_ON_DIE: - break; - - default: - dev_err(&pdev->dev, "Unsupported ECC mode!\n"); - goto release_dma_write_chan; - } - - /* - * Don't set layout for BCH4 SW ECC. This will be - * generated later in nand_bch_init() later. - */ - if (nand->ecc.mode == NAND_ECC_HW) { - switch (mtd->oobsize) { - case 16: - case 64: - case 128: - mtd_set_ooblayout(mtd, - &fsmc_ecc1_ooblayout_ops); - break; - default: - dev_warn(&pdev->dev, - "No oob scheme defined for oobsize %d\n", - mtd->oobsize); - ret = -EINVAL; - goto release_dma_write_chan; - } - } - } - - /* Second stage of scan to fill MTD data-structures */ - ret = nand_scan_tail(mtd); + nand->dummy_controller.ops = &fsmc_nand_controller_ops; + ret = nand_scan(mtd, 1); if (ret) goto release_dma_write_chan; diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c index 83697b8df871..88ea2203e263 100644 --- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c +++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c @@ -1,22 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ /* * Freescale GPMI NAND Flash Driver * * Copyright (C) 2008-2011 Freescale Semiconductor, Inc. * Copyright (C) 2008 Embedded Alley Solutions, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. */ #include <linux/delay.h> #include <linux/clk.h> diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c index f6aa358a3452..1c1ebbc82824 100644 --- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c @@ -1,22 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ /* * Freescale GPMI NAND Flash Driver * * Copyright (C) 2010-2015 Freescale Semiconductor, Inc. * Copyright (C) 2008 Embedded Alley Solutions, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. */ #include <linux/clk.h> #include <linux/slab.h> @@ -757,9 +744,9 @@ static int gpmi_alloc_dma_buffer(struct gpmi_nand_data *this) * [2] Allocate a read/write data buffer. * The gpmi_alloc_dma_buffer can be called twice. * We allocate a PAGE_SIZE length buffer if gpmi_alloc_dma_buffer - * is called before the nand_scan_ident; and we allocate a buffer - * of the real NAND page size when the gpmi_alloc_dma_buffer is - * called after the nand_scan_ident. + * is called before the NAND identification; and we allocate a + * buffer of the real NAND page size when the gpmi_alloc_dma_buffer + * is called after. */ this->data_buffer_dma = kzalloc(mtd->writesize ?: PAGE_SIZE, GFP_DMA | GFP_KERNEL); @@ -957,7 +944,6 @@ static int gpmi_ecc_read_page_data(struct nand_chip *chip, struct gpmi_nand_data *this = nand_get_controller_data(chip); struct bch_geometry *nfc_geo = &this->bch_geometry; struct mtd_info *mtd = nand_to_mtd(chip); - void *payload_virt; dma_addr_t payload_phys; unsigned int i; unsigned char *status; @@ -967,7 +953,6 @@ static int gpmi_ecc_read_page_data(struct nand_chip *chip, dev_dbg(this->dev, "page number is : %d\n", page); - payload_virt = this->payload_virt; payload_phys = this->payload_phys; if (virt_addr_valid(buf)) { @@ -976,7 +961,6 @@ static int gpmi_ecc_read_page_data(struct nand_chip *chip, dest_phys = dma_map_single(this->dev, buf, nfc_geo->payload_size, DMA_FROM_DEVICE); if (!dma_mapping_error(this->dev, dest_phys)) { - payload_virt = buf; payload_phys = dest_phys; direct = true; } @@ -1881,6 +1865,34 @@ static int gpmi_init_last(struct gpmi_nand_data *this) return 0; } +static int gpmi_nand_attach_chip(struct nand_chip *chip) +{ + struct gpmi_nand_data *this = nand_get_controller_data(chip); + int ret; + + if (chip->bbt_options & NAND_BBT_USE_FLASH) { + chip->bbt_options |= NAND_BBT_NO_OOB; + + if (of_property_read_bool(this->dev->of_node, + "fsl,no-blockmark-swap")) + this->swap_block_mark = false; + } + dev_dbg(this->dev, "Blockmark swapping %sabled\n", + this->swap_block_mark ? "en" : "dis"); + + ret = gpmi_init_last(this); + if (ret) + return ret; + + chip->options |= NAND_SKIP_BBTSCAN; + + return 0; +} + +static const struct nand_controller_ops gpmi_nand_controller_ops = { + .attach_chip = gpmi_nand_attach_chip, +}; + static int gpmi_nand_init(struct gpmi_nand_data *this) { struct nand_chip *chip = &this->nand; @@ -1921,33 +1933,15 @@ static int gpmi_nand_init(struct gpmi_nand_data *this) if (ret) goto err_out; - ret = nand_scan_ident(mtd, GPMI_IS_MX6(this) ? 2 : 1, NULL); - if (ret) - goto err_out; - - if (chip->bbt_options & NAND_BBT_USE_FLASH) { - chip->bbt_options |= NAND_BBT_NO_OOB; - - if (of_property_read_bool(this->dev->of_node, - "fsl,no-blockmark-swap")) - this->swap_block_mark = false; - } - dev_dbg(this->dev, "Blockmark swapping %sabled\n", - this->swap_block_mark ? "en" : "dis"); - - ret = gpmi_init_last(this); - if (ret) - goto err_out; - - chip->options |= NAND_SKIP_BBTSCAN; - ret = nand_scan_tail(mtd); + chip->dummy_controller.ops = &gpmi_nand_controller_ops; + ret = nand_scan(mtd, GPMI_IS_MX6(this) ? 2 : 1); if (ret) goto err_out; ret = nand_boot_init(this); if (ret) goto err_nand_cleanup; - ret = chip->scan_bbt(mtd); + ret = nand_create_bbt(chip); if (ret) goto err_nand_cleanup; diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h index 6aa10d6962d6..69cd0cbde4f2 100644 --- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h +++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h @@ -1,18 +1,9 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ /* * Freescale GPMI NAND Flash Driver * * Copyright (C) 2010-2011 Freescale Semiconductor, Inc. * Copyright (C) 2008 Embedded Alley Solutions, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ #ifndef __DRIVERS_MTD_NAND_GPMI_NAND_H #define __DRIVERS_MTD_NAND_GPMI_NAND_H diff --git a/drivers/mtd/nand/raw/hisi504_nand.c b/drivers/mtd/nand/raw/hisi504_nand.c index a1e009c8e556..950dc7789296 100644 --- a/drivers/mtd/nand/raw/hisi504_nand.c +++ b/drivers/mtd/nand/raw/hisi504_nand.c @@ -709,9 +709,50 @@ static int hisi_nfc_ecc_probe(struct hinfc_host *host) return 0; } +static int hisi_nfc_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct hinfc_host *host = nand_get_controller_data(chip); + int flag; + + host->buffer = dmam_alloc_coherent(host->dev, + mtd->writesize + mtd->oobsize, + &host->dma_buffer, GFP_KERNEL); + if (!host->buffer) + return -ENOMEM; + + host->dma_oob = host->dma_buffer + mtd->writesize; + memset(host->buffer, 0xff, mtd->writesize + mtd->oobsize); + + flag = hinfc_read(host, HINFC504_CON); + flag &= ~(HINFC504_CON_PAGESIZE_MASK << HINFC504_CON_PAGEISZE_SHIFT); + switch (mtd->writesize) { + case 2048: + flag |= (0x001 << HINFC504_CON_PAGEISZE_SHIFT); + break; + /* + * TODO: add more pagesize support, + * default pagesize has been set in hisi_nfc_host_init + */ + default: + dev_err(host->dev, "NON-2KB page size nand flash\n"); + return -EINVAL; + } + hinfc_write(host, flag, HINFC504_CON); + + if (chip->ecc.mode == NAND_ECC_HW) + hisi_nfc_ecc_probe(host); + + return 0; +} + +static const struct nand_controller_ops hisi_nfc_controller_ops = { + .attach_chip = hisi_nfc_attach_chip, +}; + static int hisi_nfc_probe(struct platform_device *pdev) { - int ret = 0, irq, flag, max_chips = HINFC504_MAX_CHIP; + int ret = 0, irq, max_chips = HINFC504_MAX_CHIP; struct device *dev = &pdev->dev; struct hinfc_host *host; struct nand_chip *chip; @@ -769,42 +810,11 @@ static int hisi_nfc_probe(struct platform_device *pdev) return ret; } - ret = nand_scan_ident(mtd, max_chips, NULL); + chip->dummy_controller.ops = &hisi_nfc_controller_ops; + ret = nand_scan(mtd, max_chips); if (ret) return ret; - host->buffer = dmam_alloc_coherent(dev, mtd->writesize + mtd->oobsize, - &host->dma_buffer, GFP_KERNEL); - if (!host->buffer) - return -ENOMEM; - - host->dma_oob = host->dma_buffer + mtd->writesize; - memset(host->buffer, 0xff, mtd->writesize + mtd->oobsize); - - flag = hinfc_read(host, HINFC504_CON); - flag &= ~(HINFC504_CON_PAGESIZE_MASK << HINFC504_CON_PAGEISZE_SHIFT); - switch (mtd->writesize) { - case 2048: - flag |= (0x001 << HINFC504_CON_PAGEISZE_SHIFT); break; - /* - * TODO: add more pagesize support, - * default pagesize has been set in hisi_nfc_host_init - */ - default: - dev_err(dev, "NON-2KB page size nand flash\n"); - return -EINVAL; - } - hinfc_write(host, flag, HINFC504_CON); - - if (chip->ecc.mode == NAND_ECC_HW) - hisi_nfc_ecc_probe(host); - - ret = nand_scan_tail(mtd); - if (ret) { - dev_err(dev, "nand_scan_tail failed: %d\n", ret); - return ret; - } - ret = mtd_device_register(mtd, NULL, 0); if (ret) { dev_err(dev, "Err MTD partition=%d\n", ret); diff --git a/drivers/mtd/nand/raw/jz4740_nand.c b/drivers/mtd/nand/raw/jz4740_nand.c index 613b00a9604b..a7515452bc59 100644 --- a/drivers/mtd/nand/raw/jz4740_nand.c +++ b/drivers/mtd/nand/raw/jz4740_nand.c @@ -13,6 +13,7 @@ * */ +#include <linux/io.h> #include <linux/ioport.h> #include <linux/kernel.h> #include <linux/module.h> @@ -23,9 +24,9 @@ #include <linux/mtd/rawnand.h> #include <linux/mtd/partitions.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> -#include <asm/mach-jz4740/jz4740_nand.h> +#include <linux/platform_data/jz4740/jz4740_nand.h> #define JZ_REG_NAND_CTRL 0x50 #define JZ_REG_NAND_ECC_CTRL 0x100 @@ -330,7 +331,7 @@ static int jz_nand_detect_bank(struct platform_device *pdev, if (chipnr == 0) { /* Detect first chip. */ - ret = nand_scan_ident(mtd, 1, NULL); + ret = nand_scan(mtd, 1); if (ret) goto notfound_id; @@ -355,7 +356,7 @@ static int jz_nand_detect_bank(struct platform_device *pdev, mtd->size += chip->chipsize; } - dev_info(&pdev->dev, "Found chip %i on bank %i\n", chipnr, bank); + dev_info(&pdev->dev, "Found chip %zu on bank %i\n", chipnr, bank); return 0; notfound_id: @@ -367,6 +368,24 @@ notfound_id: return ret; } +static int jz_nand_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct device *dev = mtd->dev.parent; + struct jz_nand_platform_data *pdata = dev_get_platdata(dev); + struct platform_device *pdev = to_platform_device(dev); + + if (pdata && pdata->ident_callback) + pdata->ident_callback(pdev, mtd, &pdata->partitions, + &pdata->num_partitions); + + return 0; +} + +static const struct nand_controller_ops jz_nand_controller_ops = { + .attach_chip = jz_nand_attach_chip, +}; + static int jz_nand_probe(struct platform_device *pdev) { int ret; @@ -410,6 +429,7 @@ static int jz_nand_probe(struct platform_device *pdev) chip->chip_delay = 50; chip->cmd_ctrl = jz_nand_cmd_ctrl; chip->select_chip = jz_nand_select_chip; + chip->dummy_controller.ops = &jz_nand_controller_ops; if (nand->busy_gpio) chip->dev_ready = jz_nand_dev_ready; @@ -455,33 +475,20 @@ static int jz_nand_probe(struct platform_device *pdev) goto err_iounmap_mmio; } - if (pdata && pdata->ident_callback) { - pdata->ident_callback(pdev, mtd, &pdata->partitions, - &pdata->num_partitions); - } - - ret = nand_scan_tail(mtd); - if (ret) { - dev_err(&pdev->dev, "Failed to scan NAND\n"); - goto err_unclaim_banks; - } - - ret = mtd_device_parse_register(mtd, NULL, NULL, - pdata ? pdata->partitions : NULL, - pdata ? pdata->num_partitions : 0); + ret = mtd_device_register(mtd, pdata ? pdata->partitions : NULL, + pdata ? pdata->num_partitions : 0); if (ret) { dev_err(&pdev->dev, "Failed to add mtd device\n"); - goto err_nand_release; + goto err_cleanup_nand; } dev_info(&pdev->dev, "Successfully registered JZ4740 NAND driver\n"); return 0; -err_nand_release: - nand_release(mtd); -err_unclaim_banks: +err_cleanup_nand: + nand_cleanup(chip); while (chipnr--) { unsigned char bank = nand->banks[chipnr]; jz_nand_iounmap_resource(nand->bank_mem[bank - 1], diff --git a/drivers/mtd/nand/raw/jz4780_nand.c b/drivers/mtd/nand/raw/jz4780_nand.c index e69f6ae4c539..db4fa60bd52a 100644 --- a/drivers/mtd/nand/raw/jz4780_nand.c +++ b/drivers/mtd/nand/raw/jz4780_nand.c @@ -44,7 +44,7 @@ struct jz4780_nand_cs { struct jz4780_nand_controller { struct device *dev; struct jz4780_bch *bch; - struct nand_hw_control controller; + struct nand_controller controller; unsigned int num_banks; struct list_head chips; int selected; @@ -65,7 +65,8 @@ static inline struct jz4780_nand_chip *to_jz4780_nand_chip(struct mtd_info *mtd) return container_of(mtd_to_nand(mtd), struct jz4780_nand_chip, chip); } -static inline struct jz4780_nand_controller *to_jz4780_nand_controller(struct nand_hw_control *ctrl) +static inline struct jz4780_nand_controller +*to_jz4780_nand_controller(struct nand_controller *ctrl) { return container_of(ctrl, struct jz4780_nand_controller, controller); } @@ -157,9 +158,8 @@ static int jz4780_nand_ecc_correct(struct mtd_info *mtd, u8 *dat, return jz4780_bch_correct(nfc->bch, ¶ms, dat, read_ecc); } -static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *dev) +static int jz4780_nand_attach_chip(struct nand_chip *chip) { - struct nand_chip *chip = &nand->chip; struct mtd_info *mtd = nand_to_mtd(chip); struct jz4780_nand_controller *nfc = to_jz4780_nand_controller(chip->controller); int eccbytes; @@ -170,7 +170,8 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de switch (chip->ecc.mode) { case NAND_ECC_HW: if (!nfc->bch) { - dev_err(dev, "HW BCH selected, but BCH controller not found\n"); + dev_err(nfc->dev, + "HW BCH selected, but BCH controller not found\n"); return -ENODEV; } @@ -179,15 +180,16 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de chip->ecc.correct = jz4780_nand_ecc_correct; /* fall through */ case NAND_ECC_SOFT: - dev_info(dev, "using %s (strength %d, size %d, bytes %d)\n", - (nfc->bch) ? "hardware BCH" : "software ECC", - chip->ecc.strength, chip->ecc.size, chip->ecc.bytes); + dev_info(nfc->dev, "using %s (strength %d, size %d, bytes %d)\n", + (nfc->bch) ? "hardware BCH" : "software ECC", + chip->ecc.strength, chip->ecc.size, chip->ecc.bytes); break; case NAND_ECC_NONE: - dev_info(dev, "not using ECC\n"); + dev_info(nfc->dev, "not using ECC\n"); break; default: - dev_err(dev, "ECC mode %d not supported\n", chip->ecc.mode); + dev_err(nfc->dev, "ECC mode %d not supported\n", + chip->ecc.mode); return -EINVAL; } @@ -199,7 +201,7 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de eccbytes = mtd->writesize / chip->ecc.size * chip->ecc.bytes; if (eccbytes > mtd->oobsize - 2) { - dev_err(dev, + dev_err(nfc->dev, "invalid ECC config: required %d ECC bytes, but only %d are available", eccbytes, mtd->oobsize - 2); return -EINVAL; @@ -210,6 +212,10 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de return 0; } +static const struct nand_controller_ops jz4780_nand_controller_ops = { + .attach_chip = jz4780_nand_attach_chip, +}; + static int jz4780_nand_init_chip(struct platform_device *pdev, struct jz4780_nand_controller *nfc, struct device_node *np, @@ -279,15 +285,8 @@ static int jz4780_nand_init_chip(struct platform_device *pdev, chip->controller = &nfc->controller; nand_set_flash_node(chip, np); - ret = nand_scan_ident(mtd, 1, NULL); - if (ret) - return ret; - - ret = jz4780_nand_init_ecc(nand, dev); - if (ret) - return ret; - - ret = nand_scan_tail(mtd); + chip->controller->ops = &jz4780_nand_controller_ops; + ret = nand_scan(mtd, 1); if (ret) return ret; @@ -368,7 +367,7 @@ static int jz4780_nand_probe(struct platform_device *pdev) nfc->dev = dev; nfc->num_banks = num_banks; - nand_hw_control_init(&nfc->controller); + nand_controller_init(&nfc->controller); INIT_LIST_HEAD(&nfc->chips); ret = jz4780_nand_init_chips(nfc, pdev); diff --git a/drivers/mtd/nand/raw/lpc32xx_mlc.c b/drivers/mtd/nand/raw/lpc32xx_mlc.c index 052d123a8304..e82abada130a 100644 --- a/drivers/mtd/nand/raw/lpc32xx_mlc.c +++ b/drivers/mtd/nand/raw/lpc32xx_mlc.c @@ -184,6 +184,7 @@ static struct nand_bbt_descr lpc32xx_nand_bbt_mirror = { }; struct lpc32xx_nand_host { + struct platform_device *pdev; struct nand_chip nand_chip; struct lpc32xx_mlc_platform_data *pdata; struct clk *clk; @@ -653,6 +654,32 @@ static struct lpc32xx_nand_cfg_mlc *lpc32xx_parse_dt(struct device *dev) return ncfg; } +static int lpc32xx_nand_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct lpc32xx_nand_host *host = nand_get_controller_data(chip); + struct device *dev = &host->pdev->dev; + + host->dma_buf = devm_kzalloc(dev, mtd->writesize, GFP_KERNEL); + if (!host->dma_buf) + return -ENOMEM; + + host->dummy_buf = devm_kzalloc(dev, mtd->writesize, GFP_KERNEL); + if (!host->dummy_buf) + return -ENOMEM; + + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.size = 512; + mtd_set_ooblayout(mtd, &lpc32xx_ooblayout_ops); + host->mlcsubpages = mtd->writesize / 512; + + return 0; +} + +static const struct nand_controller_ops lpc32xx_nand_controller_ops = { + .attach_chip = lpc32xx_nand_attach_chip, +}; + /* * Probe for NAND controller */ @@ -669,6 +696,8 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) if (!host) return -ENOMEM; + host->pdev = pdev; + rc = platform_get_resource(pdev, IORESOURCE_MEM, 0); host->io_base = devm_ioremap_resource(&pdev->dev, rc); if (IS_ERR(host->io_base)) @@ -748,31 +777,6 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) } } - /* - * Scan to find existance of the device and - * Get the type of NAND device SMALL block or LARGE block - */ - res = nand_scan_ident(mtd, 1, NULL); - if (res) - goto release_dma_chan; - - host->dma_buf = devm_kzalloc(&pdev->dev, mtd->writesize, GFP_KERNEL); - if (!host->dma_buf) { - res = -ENOMEM; - goto release_dma_chan; - } - - host->dummy_buf = devm_kzalloc(&pdev->dev, mtd->writesize, GFP_KERNEL); - if (!host->dummy_buf) { - res = -ENOMEM; - goto release_dma_chan; - } - - nand_chip->ecc.mode = NAND_ECC_HW; - nand_chip->ecc.size = 512; - mtd_set_ooblayout(mtd, &lpc32xx_ooblayout_ops); - host->mlcsubpages = mtd->writesize / 512; - /* initially clear interrupt status */ readb(MLC_IRQ_SR(host->io_base)); @@ -794,10 +798,11 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) } /* - * Fills out all the uninitialized function pointers with the defaults - * And scans for a bad block table if appropriate. + * Scan to find existence of the device and get the type of NAND device: + * SMALL block or LARGE block. */ - res = nand_scan_tail(mtd); + nand_chip->dummy_controller.ops = &lpc32xx_nand_controller_ops; + res = nand_scan(mtd, 1); if (res) goto free_irq; diff --git a/drivers/mtd/nand/raw/lpc32xx_slc.c b/drivers/mtd/nand/raw/lpc32xx_slc.c index 42820aa1abab..a4e8b7e75135 100644 --- a/drivers/mtd/nand/raw/lpc32xx_slc.c +++ b/drivers/mtd/nand/raw/lpc32xx_slc.c @@ -779,6 +779,46 @@ static struct lpc32xx_nand_cfg_slc *lpc32xx_parse_dt(struct device *dev) return ncfg; } +static int lpc32xx_nand_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct lpc32xx_nand_host *host = nand_get_controller_data(chip); + + /* OOB and ECC CPU and DMA work areas */ + host->ecc_buf = (uint32_t *)(host->data_buf + LPC32XX_DMA_DATA_SIZE); + + /* + * Small page FLASH has a unique OOB layout, but large and huge + * page FLASH use the standard layout. Small page FLASH uses a + * custom BBT marker layout. + */ + if (mtd->writesize <= 512) + mtd_set_ooblayout(mtd, &lpc32xx_ooblayout_ops); + + /* These sizes remain the same regardless of page size */ + chip->ecc.size = 256; + chip->ecc.bytes = LPC32XX_SLC_DEV_ECC_BYTES; + chip->ecc.prepad = 0; + chip->ecc.postpad = 0; + + /* + * Use a custom BBT marker setup for small page FLASH that + * won't interfere with the ECC layout. Large and huge page + * FLASH use the standard layout. + */ + if ((chip->bbt_options & NAND_BBT_USE_FLASH) && + mtd->writesize <= 512) { + chip->bbt_td = &bbt_smallpage_main_descr; + chip->bbt_md = &bbt_smallpage_mirror_descr; + } + + return 0; +} + +static const struct nand_controller_ops lpc32xx_nand_controller_ops = { + .attach_chip = lpc32xx_nand_attach_chip, +}; + /* * Probe for NAND controller */ @@ -884,41 +924,8 @@ static int lpc32xx_nand_probe(struct platform_device *pdev) } /* Find NAND device */ - res = nand_scan_ident(mtd, 1, NULL); - if (res) - goto release_dma; - - /* OOB and ECC CPU and DMA work areas */ - host->ecc_buf = (uint32_t *)(host->data_buf + LPC32XX_DMA_DATA_SIZE); - - /* - * Small page FLASH has a unique OOB layout, but large and huge - * page FLASH use the standard layout. Small page FLASH uses a - * custom BBT marker layout. - */ - if (mtd->writesize <= 512) - mtd_set_ooblayout(mtd, &lpc32xx_ooblayout_ops); - - /* These sizes remain the same regardless of page size */ - chip->ecc.size = 256; - chip->ecc.bytes = LPC32XX_SLC_DEV_ECC_BYTES; - chip->ecc.prepad = chip->ecc.postpad = 0; - - /* - * Use a custom BBT marker setup for small page FLASH that - * won't interfere with the ECC layout. Large and huge page - * FLASH use the standard layout. - */ - if ((chip->bbt_options & NAND_BBT_USE_FLASH) && - mtd->writesize <= 512) { - chip->bbt_td = &bbt_smallpage_main_descr; - chip->bbt_md = &bbt_smallpage_mirror_descr; - } - - /* - * Fills out all the uninitialized function pointers with the defaults - */ - res = nand_scan_tail(mtd); + chip->dummy_controller.ops = &lpc32xx_nand_controller_ops; + res = nand_scan(mtd, 1); if (res) goto release_dma; diff --git a/drivers/mtd/nand/raw/marvell_nand.c b/drivers/mtd/nand/raw/marvell_nand.c index ebb1d141b900..218e09431d3d 100644 --- a/drivers/mtd/nand/raw/marvell_nand.c +++ b/drivers/mtd/nand/raw/marvell_nand.c @@ -318,7 +318,7 @@ struct marvell_nfc_caps { * @dma_buf: 32-bit aligned buffer for DMA transfers (NFCv1 only) */ struct marvell_nfc { - struct nand_hw_control controller; + struct nand_controller controller; struct device *dev; void __iomem *regs; struct clk *core_clk; @@ -335,7 +335,7 @@ struct marvell_nfc { u8 *dma_buf; }; -static inline struct marvell_nfc *to_marvell_nfc(struct nand_hw_control *ctrl) +static inline struct marvell_nfc *to_marvell_nfc(struct nand_controller *ctrl) { return container_of(ctrl, struct marvell_nfc, controller); } @@ -650,11 +650,6 @@ static void marvell_nfc_select_chip(struct mtd_info *mtd, int die_nr) return; } - /* - * Do not change the timing registers when using the DT property - * marvell,nand-keep-config; in that case ->ndtr0 and ->ndtr1 from the - * marvell_nand structure are supposedly empty. - */ writel_relaxed(marvell_nand->ndtr0, nfc->regs + NDTR0); writel_relaxed(marvell_nand->ndtr1, nfc->regs + NDTR1); @@ -2157,6 +2152,7 @@ static int marvell_nand_ecc_init(struct mtd_info *mtd, break; case NAND_ECC_NONE: case NAND_ECC_SOFT: + case NAND_ECC_ON_DIE: if (!nfc->caps->is_nfcv2 && mtd->writesize != SZ_512 && mtd->writesize != SZ_2K) { dev_err(nfc->dev, "NFCv1 cannot write %d bytes pages\n", @@ -2294,6 +2290,111 @@ static int marvell_nfc_setup_data_interface(struct mtd_info *mtd, int chipnr, return 0; } +static int marvell_nand_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(nfc->dev); + int ret; + + if (pdata && pdata->flash_bbt) + chip->bbt_options |= NAND_BBT_USE_FLASH; + + if (chip->bbt_options & NAND_BBT_USE_FLASH) { + /* + * We'll use a bad block table stored in-flash and don't + * allow writing the bad block marker to the flash. + */ + chip->bbt_options |= NAND_BBT_NO_OOB_BBM; + chip->bbt_td = &bbt_main_descr; + chip->bbt_md = &bbt_mirror_descr; + } + + /* Save the chip-specific fields of NDCR */ + marvell_nand->ndcr = NDCR_PAGE_SZ(mtd->writesize); + if (chip->options & NAND_BUSWIDTH_16) + marvell_nand->ndcr |= NDCR_DWIDTH_M | NDCR_DWIDTH_C; + + /* + * On small page NANDs, only one cycle is needed to pass the + * column address. + */ + if (mtd->writesize <= 512) { + marvell_nand->addr_cyc = 1; + } else { + marvell_nand->addr_cyc = 2; + marvell_nand->ndcr |= NDCR_RA_START; + } + + /* + * Now add the number of cycles needed to pass the row + * address. + * + * Addressing a chip using CS 2 or 3 should also need the third row + * cycle but due to inconsistance in the documentation and lack of + * hardware to test this situation, this case is not supported. + */ + if (chip->options & NAND_ROW_ADDR_3) + marvell_nand->addr_cyc += 3; + else + marvell_nand->addr_cyc += 2; + + if (pdata) { + chip->ecc.size = pdata->ecc_step_size; + chip->ecc.strength = pdata->ecc_strength; + } + + ret = marvell_nand_ecc_init(mtd, &chip->ecc); + if (ret) { + dev_err(nfc->dev, "ECC init failed: %d\n", ret); + return ret; + } + + if (chip->ecc.mode == NAND_ECC_HW) { + /* + * Subpage write not available with hardware ECC, prohibit also + * subpage read as in userspace subpage access would still be + * allowed and subpage write, if used, would lead to numerous + * uncorrectable ECC errors. + */ + chip->options |= NAND_NO_SUBPAGE_WRITE; + } + + if (pdata || nfc->caps->legacy_of_bindings) { + /* + * We keep the MTD name unchanged to avoid breaking platforms + * where the MTD cmdline parser is used and the bootloader + * has not been updated to use the new naming scheme. + */ + mtd->name = "pxa3xx_nand-0"; + } else if (!mtd->name) { + /* + * If the new bindings are used and the bootloader has not been + * updated to pass a new mtdparts parameter on the cmdline, you + * should define the following property in your NAND node, ie: + * + * label = "main-storage"; + * + * This way, mtd->name will be set by the core when + * nand_set_flash_node() is called. + */ + mtd->name = devm_kasprintf(nfc->dev, GFP_KERNEL, + "%s:nand.%d", dev_name(nfc->dev), + marvell_nand->sels[0].cs); + if (!mtd->name) { + dev_err(nfc->dev, "Failed to allocate mtd->name\n"); + return -ENOMEM; + } + } + + return 0; +} + +static const struct nand_controller_ops marvell_nand_controller_ops = { + .attach_chip = marvell_nand_attach_chip, +}; + static int marvell_nand_chip_init(struct device *dev, struct marvell_nfc *nfc, struct device_node *np) { @@ -2436,105 +2537,10 @@ static int marvell_nand_chip_init(struct device *dev, struct marvell_nfc *nfc, marvell_nand->ndtr1 = readl_relaxed(nfc->regs + NDTR1); chip->options |= NAND_BUSWIDTH_AUTO; - ret = nand_scan_ident(mtd, marvell_nand->nsels, NULL); - if (ret) { - dev_err(dev, "could not identify the nand chip\n"); - return ret; - } - - if (pdata && pdata->flash_bbt) - chip->bbt_options |= NAND_BBT_USE_FLASH; - - if (chip->bbt_options & NAND_BBT_USE_FLASH) { - /* - * We'll use a bad block table stored in-flash and don't - * allow writing the bad block marker to the flash. - */ - chip->bbt_options |= NAND_BBT_NO_OOB_BBM; - chip->bbt_td = &bbt_main_descr; - chip->bbt_md = &bbt_mirror_descr; - } - - /* Save the chip-specific fields of NDCR */ - marvell_nand->ndcr = NDCR_PAGE_SZ(mtd->writesize); - if (chip->options & NAND_BUSWIDTH_16) - marvell_nand->ndcr |= NDCR_DWIDTH_M | NDCR_DWIDTH_C; - - /* - * On small page NANDs, only one cycle is needed to pass the - * column address. - */ - if (mtd->writesize <= 512) { - marvell_nand->addr_cyc = 1; - } else { - marvell_nand->addr_cyc = 2; - marvell_nand->ndcr |= NDCR_RA_START; - } - - /* - * Now add the number of cycles needed to pass the row - * address. - * - * Addressing a chip using CS 2 or 3 should also need the third row - * cycle but due to inconsistance in the documentation and lack of - * hardware to test this situation, this case is not supported. - */ - if (chip->options & NAND_ROW_ADDR_3) - marvell_nand->addr_cyc += 3; - else - marvell_nand->addr_cyc += 2; - - if (pdata) { - chip->ecc.size = pdata->ecc_step_size; - chip->ecc.strength = pdata->ecc_strength; - } - ret = marvell_nand_ecc_init(mtd, &chip->ecc); + ret = nand_scan(mtd, marvell_nand->nsels); if (ret) { - dev_err(dev, "ECC init failed: %d\n", ret); - return ret; - } - - if (chip->ecc.mode == NAND_ECC_HW) { - /* - * Subpage write not available with hardware ECC, prohibit also - * subpage read as in userspace subpage access would still be - * allowed and subpage write, if used, would lead to numerous - * uncorrectable ECC errors. - */ - chip->options |= NAND_NO_SUBPAGE_WRITE; - } - - if (pdata || nfc->caps->legacy_of_bindings) { - /* - * We keep the MTD name unchanged to avoid breaking platforms - * where the MTD cmdline parser is used and the bootloader - * has not been updated to use the new naming scheme. - */ - mtd->name = "pxa3xx_nand-0"; - } else if (!mtd->name) { - /* - * If the new bindings are used and the bootloader has not been - * updated to pass a new mtdparts parameter on the cmdline, you - * should define the following property in your NAND node, ie: - * - * label = "main-storage"; - * - * This way, mtd->name will be set by the core when - * nand_set_flash_node() is called. - */ - mtd->name = devm_kasprintf(nfc->dev, GFP_KERNEL, - "%s:nand.%d", dev_name(nfc->dev), - marvell_nand->sels[0].cs); - if (!mtd->name) { - dev_err(nfc->dev, "Failed to allocate mtd->name\n"); - return -ENOMEM; - } - } - - ret = nand_scan_tail(mtd); - if (ret) { - dev_err(dev, "nand_scan_tail failed: %d\n", ret); + dev_err(dev, "could not scan the nand chip\n"); return ret; } @@ -2677,6 +2683,21 @@ static int marvell_nfc_init_dma(struct marvell_nfc *nfc) return 0; } +static void marvell_nfc_reset(struct marvell_nfc *nfc) +{ + /* + * ECC operations and interruptions are only enabled when specifically + * needed. ECC shall not be activated in the early stages (fails probe). + * Arbiter flag, even if marked as "reserved", must be set (empirical). + * SPARE_EN bit must always be set or ECC bytes will not be at the same + * offset in the read page and this will fail the protection. + */ + writel_relaxed(NDCR_ALL_INT | NDCR_ND_ARB_EN | NDCR_SPARE_EN | + NDCR_RD_ID_CNT(NFCV1_READID_LEN), nfc->regs + NDCR); + writel_relaxed(0xFFFFFFFF, nfc->regs + NDSR); + writel_relaxed(0, nfc->regs + NDECCCTRL); +} + static int marvell_nfc_init(struct marvell_nfc *nfc) { struct device_node *np = nfc->dev->of_node; @@ -2715,17 +2736,7 @@ static int marvell_nfc_init(struct marvell_nfc *nfc) if (!nfc->caps->is_nfcv2) marvell_nfc_init_dma(nfc); - /* - * ECC operations and interruptions are only enabled when specifically - * needed. ECC shall not be activated in the early stages (fails probe). - * Arbiter flag, even if marked as "reserved", must be set (empirical). - * SPARE_EN bit must always be set or ECC bytes will not be at the same - * offset in the read page and this will fail the protection. - */ - writel_relaxed(NDCR_ALL_INT | NDCR_ND_ARB_EN | NDCR_SPARE_EN | - NDCR_RD_ID_CNT(NFCV1_READID_LEN), nfc->regs + NDCR); - writel_relaxed(0xFFFFFFFF, nfc->regs + NDSR); - writel_relaxed(0, nfc->regs + NDECCCTRL); + marvell_nfc_reset(nfc); return 0; } @@ -2744,7 +2755,8 @@ static int marvell_nfc_probe(struct platform_device *pdev) return -ENOMEM; nfc->dev = dev; - nand_hw_control_init(&nfc->controller); + nand_controller_init(&nfc->controller); + nfc->controller.ops = &marvell_nand_controller_ops; INIT_LIST_HEAD(&nfc->chips); r = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -2772,17 +2784,19 @@ static int marvell_nfc_probe(struct platform_device *pdev) return ret; nfc->reg_clk = devm_clk_get(&pdev->dev, "reg"); - if (PTR_ERR(nfc->reg_clk) != -ENOENT) { - if (!IS_ERR(nfc->reg_clk)) { - ret = clk_prepare_enable(nfc->reg_clk); - if (ret) - goto unprepare_core_clk; - } else { + if (IS_ERR(nfc->reg_clk)) { + if (PTR_ERR(nfc->reg_clk) != -ENOENT) { ret = PTR_ERR(nfc->reg_clk); goto unprepare_core_clk; } + + nfc->reg_clk = NULL; } + ret = clk_prepare_enable(nfc->reg_clk); + if (ret) + goto unprepare_core_clk; + marvell_nfc_disable_int(nfc, NDCR_ALL_INT); marvell_nfc_clear_int(nfc, NDCR_ALL_INT); ret = devm_request_irq(dev, irq, marvell_nfc_isr, @@ -2840,6 +2854,49 @@ static int marvell_nfc_remove(struct platform_device *pdev) return 0; } +static int __maybe_unused marvell_nfc_suspend(struct device *dev) +{ + struct marvell_nfc *nfc = dev_get_drvdata(dev); + struct marvell_nand_chip *chip; + + list_for_each_entry(chip, &nfc->chips, node) + marvell_nfc_wait_ndrun(&chip->chip); + + clk_disable_unprepare(nfc->reg_clk); + clk_disable_unprepare(nfc->core_clk); + + return 0; +} + +static int __maybe_unused marvell_nfc_resume(struct device *dev) +{ + struct marvell_nfc *nfc = dev_get_drvdata(dev); + int ret; + + ret = clk_prepare_enable(nfc->core_clk); + if (ret < 0) + return ret; + + ret = clk_prepare_enable(nfc->reg_clk); + if (ret < 0) + return ret; + + /* + * Reset nfc->selected_chip so the next command will cause the timing + * registers to be restored in marvell_nfc_select_chip(). + */ + nfc->selected_chip = NULL; + + /* Reset registers that have lost their contents */ + marvell_nfc_reset(nfc); + + return 0; +} + +static const struct dev_pm_ops marvell_nfc_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(marvell_nfc_suspend, marvell_nfc_resume) +}; + static const struct marvell_nfc_caps marvell_armada_8k_nfc_caps = { .max_cs_nb = 4, .max_rb_nb = 2, @@ -2924,6 +2981,7 @@ static struct platform_driver marvell_nfc_driver = { .driver = { .name = "marvell-nfc", .of_match_table = marvell_nfc_of_ids, + .pm = &marvell_nfc_pm_ops, }, .id_table = marvell_nfc_platform_ids, .probe = marvell_nfc_probe, diff --git a/drivers/mtd/nand/raw/mtk_nand.c b/drivers/mtd/nand/raw/mtk_nand.c index 75c845adb050..57b5ed1699e3 100644 --- a/drivers/mtd/nand/raw/mtk_nand.c +++ b/drivers/mtd/nand/raw/mtk_nand.c @@ -145,7 +145,7 @@ struct mtk_nfc_clk { }; struct mtk_nfc { - struct nand_hw_control controller; + struct nand_controller controller; struct mtk_ecc_config ecc_cfg; struct mtk_nfc_clk clk; struct mtk_ecc *ecc; @@ -1250,13 +1250,54 @@ static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd) return 0; } +static int mtk_nfc_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct device *dev = mtd->dev.parent; + struct mtk_nfc *nfc = nand_get_controller_data(chip); + struct mtk_nfc_nand_chip *mtk_nand = to_mtk_nand(chip); + int len; + int ret; + + if (chip->options & NAND_BUSWIDTH_16) { + dev_err(dev, "16bits buswidth not supported"); + return -EINVAL; + } + + /* store bbt magic in page, cause OOB is not protected */ + if (chip->bbt_options & NAND_BBT_USE_FLASH) + chip->bbt_options |= NAND_BBT_NO_OOB; + + ret = mtk_nfc_ecc_init(dev, mtd); + if (ret) + return ret; + + ret = mtk_nfc_set_spare_per_sector(&mtk_nand->spare_per_sector, mtd); + if (ret) + return ret; + + mtk_nfc_set_fdm(&mtk_nand->fdm, mtd); + mtk_nfc_set_bad_mark_ctl(&mtk_nand->bad_mark, mtd); + + len = mtd->writesize + mtd->oobsize; + nfc->buffer = devm_kzalloc(dev, len, GFP_KERNEL); + if (!nfc->buffer) + return -ENOMEM; + + return 0; +} + +static const struct nand_controller_ops mtk_nfc_controller_ops = { + .attach_chip = mtk_nfc_attach_chip, +}; + static int mtk_nfc_nand_chip_init(struct device *dev, struct mtk_nfc *nfc, struct device_node *np) { struct mtk_nfc_nand_chip *chip; struct nand_chip *nand; struct mtd_info *mtd; - int nsels, len; + int nsels; u32 tmp; int ret; int i; @@ -1324,40 +1365,11 @@ static int mtk_nfc_nand_chip_init(struct device *dev, struct mtk_nfc *nfc, mtk_nfc_hw_init(nfc); - ret = nand_scan_ident(mtd, nsels, NULL); - if (ret) - return ret; - - /* store bbt magic in page, cause OOB is not protected */ - if (nand->bbt_options & NAND_BBT_USE_FLASH) - nand->bbt_options |= NAND_BBT_NO_OOB; - - ret = mtk_nfc_ecc_init(dev, mtd); - if (ret) - return -EINVAL; - - if (nand->options & NAND_BUSWIDTH_16) { - dev_err(dev, "16bits buswidth not supported"); - return -EINVAL; - } - - ret = mtk_nfc_set_spare_per_sector(&chip->spare_per_sector, mtd); - if (ret) - return ret; - - mtk_nfc_set_fdm(&chip->fdm, mtd); - mtk_nfc_set_bad_mark_ctl(&chip->bad_mark, mtd); - - len = mtd->writesize + mtd->oobsize; - nfc->buffer = devm_kzalloc(dev, len, GFP_KERNEL); - if (!nfc->buffer) - return -ENOMEM; - - ret = nand_scan_tail(mtd); + ret = nand_scan(mtd, nsels); if (ret) return ret; - ret = mtd_device_parse_register(mtd, NULL, NULL, NULL, 0); + ret = mtd_device_register(mtd, NULL, 0); if (ret) { dev_err(dev, "mtd parse partition error\n"); nand_release(mtd); @@ -1443,6 +1455,7 @@ static int mtk_nfc_probe(struct platform_device *pdev) spin_lock_init(&nfc->controller.lock); init_waitqueue_head(&nfc->controller.wq); INIT_LIST_HEAD(&nfc->chips); + nfc->controller.ops = &mtk_nfc_controller_ops; /* probe defer if not ready */ nfc->ecc = of_mtk_ecc_get(np); diff --git a/drivers/mtd/nand/raw/mxc_nand.c b/drivers/mtd/nand/raw/mxc_nand.c index 26cef218bb43..4c9214dea424 100644 --- a/drivers/mtd/nand/raw/mxc_nand.c +++ b/drivers/mtd/nand/raw/mxc_nand.c @@ -1,20 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved. * Copyright 2008 Sascha Hauer, kernel@pengutronix.de - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301, USA. */ #include <linux/delay.h> @@ -34,8 +21,6 @@ #include <linux/completion.h> #include <linux/of.h> #include <linux/of_device.h> - -#include <asm/mach/flash.h> #include <linux/platform_data/mtd-mxc_nand.h> #define DRIVER_NAME "mxc_nand" @@ -1686,7 +1671,7 @@ static const struct of_device_id mxcnd_dt_ids[] = { }; MODULE_DEVICE_TABLE(of, mxcnd_dt_ids); -static int __init mxcnd_probe_dt(struct mxc_nand_host *host) +static int mxcnd_probe_dt(struct mxc_nand_host *host) { struct device_node *np = host->dev->of_node; const struct of_device_id *of_id = @@ -1700,12 +1685,80 @@ static int __init mxcnd_probe_dt(struct mxc_nand_host *host) return 0; } #else -static int __init mxcnd_probe_dt(struct mxc_nand_host *host) +static int mxcnd_probe_dt(struct mxc_nand_host *host) { return 1; } #endif +static int mxcnd_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct mxc_nand_host *host = nand_get_controller_data(chip); + struct device *dev = mtd->dev.parent; + + switch (chip->ecc.mode) { + case NAND_ECC_HW: + chip->ecc.read_page = mxc_nand_read_page; + chip->ecc.read_page_raw = mxc_nand_read_page_raw; + chip->ecc.read_oob = mxc_nand_read_oob; + chip->ecc.write_page = mxc_nand_write_page_ecc; + chip->ecc.write_page_raw = mxc_nand_write_page_raw; + chip->ecc.write_oob = mxc_nand_write_oob; + break; + + case NAND_ECC_SOFT: + break; + + default: + return -EINVAL; + } + + if (chip->bbt_options & NAND_BBT_USE_FLASH) { + chip->bbt_td = &bbt_main_descr; + chip->bbt_md = &bbt_mirror_descr; + } + + /* Allocate the right size buffer now */ + devm_kfree(dev, (void *)host->data_buf); + host->data_buf = devm_kzalloc(dev, mtd->writesize + mtd->oobsize, + GFP_KERNEL); + if (!host->data_buf) + return -ENOMEM; + + /* Call preset again, with correct writesize chip time */ + host->devtype_data->preset(mtd); + + if (!chip->ecc.bytes) { + if (host->eccsize == 8) + chip->ecc.bytes = 18; + else if (host->eccsize == 4) + chip->ecc.bytes = 9; + } + + /* + * Experimentation shows that i.MX NFC can only handle up to 218 oob + * bytes. Limit used_oobsize to 218 so as to not confuse copy_spare() + * into copying invalid data to/from the spare IO buffer, as this + * might cause ECC data corruption when doing sub-page write to a + * partially written page. + */ + host->used_oobsize = min(mtd->oobsize, 218U); + + if (chip->ecc.mode == NAND_ECC_HW) { + if (is_imx21_nfc(host) || is_imx27_nfc(host)) + chip->ecc.strength = 1; + else + chip->ecc.strength = (host->eccsize == 4) ? 4 : 8; + } + + return 0; +} + +static const struct nand_controller_ops mxcnd_controller_ops = { + .attach_chip = mxcnd_attach_chip, +}; + static int mxcnd_probe(struct platform_device *pdev) { struct nand_chip *this; @@ -1845,71 +1898,9 @@ static int mxcnd_probe(struct platform_device *pdev) host->devtype_data->irq_control(host, 1); } - /* first scan to find the device and get the page size */ - err = nand_scan_ident(mtd, is_imx25_nfc(host) ? 4 : 1, NULL); - if (err) - goto escan; - - switch (this->ecc.mode) { - case NAND_ECC_HW: - this->ecc.read_page = mxc_nand_read_page; - this->ecc.read_page_raw = mxc_nand_read_page_raw; - this->ecc.read_oob = mxc_nand_read_oob; - this->ecc.write_page = mxc_nand_write_page_ecc; - this->ecc.write_page_raw = mxc_nand_write_page_raw; - this->ecc.write_oob = mxc_nand_write_oob; - break; - - case NAND_ECC_SOFT: - break; - - default: - err = -EINVAL; - goto escan; - } - - if (this->bbt_options & NAND_BBT_USE_FLASH) { - this->bbt_td = &bbt_main_descr; - this->bbt_md = &bbt_mirror_descr; - } - - /* allocate the right size buffer now */ - devm_kfree(&pdev->dev, (void *)host->data_buf); - host->data_buf = devm_kzalloc(&pdev->dev, mtd->writesize + mtd->oobsize, - GFP_KERNEL); - if (!host->data_buf) { - err = -ENOMEM; - goto escan; - } - - /* Call preset again, with correct writesize this time */ - host->devtype_data->preset(mtd); - - if (!this->ecc.bytes) { - if (host->eccsize == 8) - this->ecc.bytes = 18; - else if (host->eccsize == 4) - this->ecc.bytes = 9; - } - - /* - * Experimentation shows that i.MX NFC can only handle up to 218 oob - * bytes. Limit used_oobsize to 218 so as to not confuse copy_spare() - * into copying invalid data to/from the spare IO buffer, as this - * might cause ECC data corruption when doing sub-page write to a - * partially written page. - */ - host->used_oobsize = min(mtd->oobsize, 218U); - - if (this->ecc.mode == NAND_ECC_HW) { - if (is_imx21_nfc(host) || is_imx27_nfc(host)) - this->ecc.strength = 1; - else - this->ecc.strength = (host->eccsize == 4) ? 4 : 8; - } - - /* second phase scan */ - err = nand_scan_tail(mtd); + /* Scan the NAND device */ + this->dummy_controller.ops = &mxcnd_controller_ops; + err = nand_scan(mtd, is_imx25_nfc(host) ? 4 : 1); if (err) goto escan; diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c index b01d15ec4c56..d527e448ce19 100644 --- a/drivers/mtd/nand/raw/nand_base.c +++ b/drivers/mtd/nand/raw/nand_base.c @@ -2668,8 +2668,8 @@ static bool nand_subop_instr_is_valid(const struct nand_subop *subop, return subop && instr_idx < subop->ninstrs; } -static int nand_subop_get_start_off(const struct nand_subop *subop, - unsigned int instr_idx) +static unsigned int nand_subop_get_start_off(const struct nand_subop *subop, + unsigned int instr_idx) { if (instr_idx) return 0; @@ -2688,12 +2688,12 @@ static int nand_subop_get_start_off(const struct nand_subop *subop, * * Given an address instruction, returns the offset of the first cycle to issue. */ -int nand_subop_get_addr_start_off(const struct nand_subop *subop, - unsigned int instr_idx) +unsigned int nand_subop_get_addr_start_off(const struct nand_subop *subop, + unsigned int instr_idx) { - if (!nand_subop_instr_is_valid(subop, instr_idx) || - subop->instrs[instr_idx].type != NAND_OP_ADDR_INSTR) - return -EINVAL; + if (WARN_ON(!nand_subop_instr_is_valid(subop, instr_idx) || + subop->instrs[instr_idx].type != NAND_OP_ADDR_INSTR)) + return 0; return nand_subop_get_start_off(subop, instr_idx); } @@ -2710,14 +2710,14 @@ EXPORT_SYMBOL_GPL(nand_subop_get_addr_start_off); * * Given an address instruction, returns the number of address cycle to issue. */ -int nand_subop_get_num_addr_cyc(const struct nand_subop *subop, - unsigned int instr_idx) +unsigned int nand_subop_get_num_addr_cyc(const struct nand_subop *subop, + unsigned int instr_idx) { int start_off, end_off; - if (!nand_subop_instr_is_valid(subop, instr_idx) || - subop->instrs[instr_idx].type != NAND_OP_ADDR_INSTR) - return -EINVAL; + if (WARN_ON(!nand_subop_instr_is_valid(subop, instr_idx) || + subop->instrs[instr_idx].type != NAND_OP_ADDR_INSTR)) + return 0; start_off = nand_subop_get_addr_start_off(subop, instr_idx); @@ -2742,12 +2742,12 @@ EXPORT_SYMBOL_GPL(nand_subop_get_num_addr_cyc); * * Given a data instruction, returns the offset to start from. */ -int nand_subop_get_data_start_off(const struct nand_subop *subop, - unsigned int instr_idx) +unsigned int nand_subop_get_data_start_off(const struct nand_subop *subop, + unsigned int instr_idx) { - if (!nand_subop_instr_is_valid(subop, instr_idx) || - !nand_instr_is_data(&subop->instrs[instr_idx])) - return -EINVAL; + if (WARN_ON(!nand_subop_instr_is_valid(subop, instr_idx) || + !nand_instr_is_data(&subop->instrs[instr_idx]))) + return 0; return nand_subop_get_start_off(subop, instr_idx); } @@ -2764,14 +2764,14 @@ EXPORT_SYMBOL_GPL(nand_subop_get_data_start_off); * * Returns the length of the chunk of data to send/receive. */ -int nand_subop_get_data_len(const struct nand_subop *subop, - unsigned int instr_idx) +unsigned int nand_subop_get_data_len(const struct nand_subop *subop, + unsigned int instr_idx) { int start_off = 0, end_off; - if (!nand_subop_instr_is_valid(subop, instr_idx) || - !nand_instr_is_data(&subop->instrs[instr_idx])) - return -EINVAL; + if (WARN_ON(!nand_subop_instr_is_valid(subop, instr_idx) || + !nand_instr_is_data(&subop->instrs[instr_idx]))) + return 0; start_off = nand_subop_get_data_start_off(subop, instr_idx); @@ -2967,6 +2967,23 @@ int nand_check_erased_ecc_chunk(void *data, int datalen, EXPORT_SYMBOL(nand_check_erased_ecc_chunk); /** + * nand_read_page_raw_notsupp - dummy read raw page function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: buffer to store read data + * @oob_required: caller requires OOB data read to chip->oob_poi + * @page: page number to read + * + * Returns -ENOTSUPP unconditionally. + */ +int nand_read_page_raw_notsupp(struct mtd_info *mtd, struct nand_chip *chip, + u8 *buf, int oob_required, int page) +{ + return -ENOTSUPP; +} +EXPORT_SYMBOL(nand_read_page_raw_notsupp); + +/** * nand_read_page_raw - [INTERN] read raw page data without ecc * @mtd: mtd info structure * @chip: nand chip info structure @@ -3960,6 +3977,22 @@ static int nand_read_oob(struct mtd_info *mtd, loff_t from, return ret; } +/** + * nand_write_page_raw_notsupp - dummy raw page write function + * @mtd: mtd info structure + * @chip: nand chip info structure + * @buf: data buffer + * @oob_required: must write chip->oob_poi to OOB + * @page: page number to write + * + * Returns -ENOTSUPP unconditionally. + */ +int nand_write_page_raw_notsupp(struct mtd_info *mtd, struct nand_chip *chip, + const u8 *buf, int oob_required, int page) +{ + return -ENOTSUPP; +} +EXPORT_SYMBOL(nand_write_page_raw_notsupp); /** * nand_write_page_raw - [INTERN] raw page write function @@ -4965,12 +4998,10 @@ static void nand_set_defaults(struct nand_chip *chip) chip->write_byte = busw ? nand_write_byte16 : nand_write_byte; if (!chip->read_buf || chip->read_buf == nand_read_buf) chip->read_buf = busw ? nand_read_buf16 : nand_read_buf; - if (!chip->scan_bbt) - chip->scan_bbt = nand_default_bbt; if (!chip->controller) { - chip->controller = &chip->hwcontrol; - nand_hw_control_init(chip->controller); + chip->controller = &chip->dummy_controller; + nand_controller_init(chip->controller); } if (!chip->buf_align) @@ -5120,6 +5151,8 @@ static int nand_flash_detect_onfi(struct nand_chip *chip) { struct mtd_info *mtd = nand_to_mtd(chip); struct nand_onfi_params *p; + struct onfi_params *onfi; + int onfi_version = 0; char id[4]; int i, ret, val; @@ -5168,30 +5201,35 @@ static int nand_flash_detect_onfi(struct nand_chip *chip) } } + if (chip->manufacturer.desc && chip->manufacturer.desc->ops && + chip->manufacturer.desc->ops->fixup_onfi_param_page) + chip->manufacturer.desc->ops->fixup_onfi_param_page(chip, p); + /* Check version */ val = le16_to_cpu(p->revision); - if (val & (1 << 5)) - chip->parameters.onfi.version = 23; - else if (val & (1 << 4)) - chip->parameters.onfi.version = 22; - else if (val & (1 << 3)) - chip->parameters.onfi.version = 21; - else if (val & (1 << 2)) - chip->parameters.onfi.version = 20; - else if (val & (1 << 1)) - chip->parameters.onfi.version = 10; - - if (!chip->parameters.onfi.version) { + if (val & ONFI_VERSION_2_3) + onfi_version = 23; + else if (val & ONFI_VERSION_2_2) + onfi_version = 22; + else if (val & ONFI_VERSION_2_1) + onfi_version = 21; + else if (val & ONFI_VERSION_2_0) + onfi_version = 20; + else if (val & ONFI_VERSION_1_0) + onfi_version = 10; + + if (!onfi_version) { pr_info("unsupported ONFI version: %d\n", val); goto free_onfi_param_page; - } else { - ret = 1; } sanitize_string(p->manufacturer, sizeof(p->manufacturer)); sanitize_string(p->model, sizeof(p->model)); - strncpy(chip->parameters.model, p->model, - sizeof(chip->parameters.model) - 1); + chip->parameters.model = kstrdup(p->model, GFP_KERNEL); + if (!chip->parameters.model) { + ret = -ENOMEM; + goto free_onfi_param_page; + } mtd->writesize = le32_to_cpu(p->byte_per_page); @@ -5219,7 +5257,7 @@ static int nand_flash_detect_onfi(struct nand_chip *chip) if (p->ecc_bits != 0xff) { chip->ecc_strength_ds = p->ecc_bits; chip->ecc_step_ds = 512; - } else if (chip->parameters.onfi.version >= 21 && + } else if (onfi_version >= 21 && (le16_to_cpu(p->features) & ONFI_FEATURE_EXT_PARAM_PAGE)) { /* @@ -5246,19 +5284,33 @@ static int nand_flash_detect_onfi(struct nand_chip *chip) bitmap_set(chip->parameters.set_feature_list, ONFI_FEATURE_ADDR_TIMING_MODE, 1); } - chip->parameters.onfi.tPROG = le16_to_cpu(p->t_prog); - chip->parameters.onfi.tBERS = le16_to_cpu(p->t_bers); - chip->parameters.onfi.tR = le16_to_cpu(p->t_r); - chip->parameters.onfi.tCCS = le16_to_cpu(p->t_ccs); - chip->parameters.onfi.async_timing_mode = - le16_to_cpu(p->async_timing_mode); - chip->parameters.onfi.vendor_revision = - le16_to_cpu(p->vendor_revision); - memcpy(chip->parameters.onfi.vendor, p->vendor, - sizeof(p->vendor)); + onfi = kzalloc(sizeof(*onfi), GFP_KERNEL); + if (!onfi) { + ret = -ENOMEM; + goto free_model; + } + + onfi->version = onfi_version; + onfi->tPROG = le16_to_cpu(p->t_prog); + onfi->tBERS = le16_to_cpu(p->t_bers); + onfi->tR = le16_to_cpu(p->t_r); + onfi->tCCS = le16_to_cpu(p->t_ccs); + onfi->async_timing_mode = le16_to_cpu(p->async_timing_mode); + onfi->vendor_revision = le16_to_cpu(p->vendor_revision); + memcpy(onfi->vendor, p->vendor, sizeof(p->vendor)); + chip->parameters.onfi = onfi; + + /* Identification done, free the full ONFI parameter page and exit */ + kfree(p); + + return 1; + +free_model: + kfree(chip->parameters.model); free_onfi_param_page: kfree(p); + return ret; } @@ -5321,8 +5373,11 @@ static int nand_flash_detect_jedec(struct nand_chip *chip) sanitize_string(p->manufacturer, sizeof(p->manufacturer)); sanitize_string(p->model, sizeof(p->model)); - strncpy(chip->parameters.model, p->model, - sizeof(chip->parameters.model) - 1); + chip->parameters.model = kstrdup(p->model, GFP_KERNEL); + if (!chip->parameters.model) { + ret = -ENOMEM; + goto free_jedec_param_page; + } mtd->writesize = le32_to_cpu(p->byte_per_page); @@ -5511,8 +5566,9 @@ static bool find_full_id_nand(struct nand_chip *chip, chip->onfi_timing_mode_default = type->onfi_timing_mode_default; - strncpy(chip->parameters.model, type->name, - sizeof(chip->parameters.model) - 1); + chip->parameters.model = kstrdup(type->name, GFP_KERNEL); + if (!chip->parameters.model) + return false; return true; } @@ -5651,7 +5707,6 @@ static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type) } } - chip->parameters.onfi.version = 0; if (!type->name || !type->pagesize) { /* Check if the chip is ONFI compliant */ ret = nand_flash_detect_onfi(chip); @@ -5671,8 +5726,9 @@ static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type) if (!type->name) return -ENODEV; - strncpy(chip->parameters.model, type->name, - sizeof(chip->parameters.model) - 1); + chip->parameters.model = kstrdup(type->name, GFP_KERNEL); + if (!chip->parameters.model) + return -ENOMEM; chip->chipsize = (uint64_t)type->chipsize << 20; @@ -5702,7 +5758,9 @@ ident_done: mtd->name); pr_warn("bus width %d instead of %d bits\n", busw ? 16 : 8, (chip->options & NAND_BUSWIDTH_16) ? 16 : 8); - return -EINVAL; + ret = -EINVAL; + + goto free_detect_allocation; } nand_decode_bbm_options(chip); @@ -5739,6 +5797,11 @@ ident_done: (int)(chip->chipsize >> 20), nand_is_slc(chip) ? "SLC" : "MLC", mtd->erasesize >> 10, mtd->writesize, mtd->oobsize); return 0; + +free_detect_allocation: + kfree(chip->parameters.model); + + return ret; } static const char * const nand_ecc_modes[] = { @@ -5777,6 +5840,7 @@ static int of_get_nand_ecc_mode(struct device_node *np) static const char * const nand_ecc_algos[] = { [NAND_ECC_HAMMING] = "hamming", [NAND_ECC_BCH] = "bch", + [NAND_ECC_RS] = "rs", }; static int of_get_nand_ecc_algo(struct device_node *np) @@ -5858,6 +5922,9 @@ static int nand_dt_init(struct nand_chip *chip) if (of_get_nand_bus_width(dn) == 16) chip->options |= NAND_BUSWIDTH_16; + if (of_property_read_bool(dn, "nand-is-boot-medium")) + chip->options |= NAND_IS_BOOT_MEDIUM; + if (of_get_nand_on_flash_bbt(dn)) chip->bbt_options |= NAND_BBT_USE_FLASH; @@ -5885,7 +5952,7 @@ static int nand_dt_init(struct nand_chip *chip) } /** - * nand_scan_ident - [NAND Interface] Scan for the NAND device + * nand_scan_ident - Scan for the NAND device * @mtd: MTD device structure * @maxchips: number of chips to scan for * @table: alternative NAND ID table @@ -5893,9 +5960,13 @@ static int nand_dt_init(struct nand_chip *chip) * This is the first phase of the normal nand_scan() function. It reads the * flash ID and sets up MTD fields accordingly. * + * This helper used to be called directly from controller drivers that needed + * to tweak some ECC-related parameters before nand_scan_tail(). This separation + * prevented dynamic allocations during this phase which was unconvenient and + * as been banned for the benefit of the ->init_ecc()/cleanup_ecc() hooks. */ -int nand_scan_ident(struct mtd_info *mtd, int maxchips, - struct nand_flash_dev *table) +static int nand_scan_ident(struct mtd_info *mtd, int maxchips, + struct nand_flash_dev *table) { int i, nand_maf_id, nand_dev_id; struct nand_chip *chip = mtd_to_nand(mtd); @@ -5969,7 +6040,12 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips, return 0; } -EXPORT_SYMBOL(nand_scan_ident); + +static void nand_scan_ident_cleanup(struct nand_chip *chip) +{ + kfree(chip->parameters.model); + kfree(chip->parameters.onfi); +} static int nand_set_ecc_soft_ops(struct mtd_info *mtd) { @@ -6077,24 +6153,17 @@ static int nand_set_ecc_soft_ops(struct mtd_info *mtd) * by the controller and the calculated ECC bytes fit within the chip's OOB. * On success, the calculated ECC bytes is set. */ -int nand_check_ecc_caps(struct nand_chip *chip, - const struct nand_ecc_caps *caps, int oobavail) +static int +nand_check_ecc_caps(struct nand_chip *chip, + const struct nand_ecc_caps *caps, int oobavail) { struct mtd_info *mtd = nand_to_mtd(chip); const struct nand_ecc_step_info *stepinfo; int preset_step = chip->ecc.size; int preset_strength = chip->ecc.strength; - int nsteps, ecc_bytes; + int ecc_bytes, nsteps = mtd->writesize / preset_step; int i, j; - if (WARN_ON(oobavail < 0)) - return -EINVAL; - - if (!preset_step || !preset_strength) - return -ENODATA; - - nsteps = mtd->writesize / preset_step; - for (i = 0; i < caps->nstepinfos; i++) { stepinfo = &caps->stepinfos[i]; @@ -6127,7 +6196,6 @@ int nand_check_ecc_caps(struct nand_chip *chip, return -ENOTSUPP; } -EXPORT_SYMBOL_GPL(nand_check_ecc_caps); /** * nand_match_ecc_req - meet the chip's requirement with least ECC bytes @@ -6139,8 +6207,9 @@ EXPORT_SYMBOL_GPL(nand_check_ecc_caps); * number of ECC bytes (i.e. with the largest number of OOB-free bytes). * On success, the chosen ECC settings are set. */ -int nand_match_ecc_req(struct nand_chip *chip, - const struct nand_ecc_caps *caps, int oobavail) +static int +nand_match_ecc_req(struct nand_chip *chip, + const struct nand_ecc_caps *caps, int oobavail) { struct mtd_info *mtd = nand_to_mtd(chip); const struct nand_ecc_step_info *stepinfo; @@ -6151,9 +6220,6 @@ int nand_match_ecc_req(struct nand_chip *chip, int best_ecc_bytes_total = INT_MAX; int i, j; - if (WARN_ON(oobavail < 0)) - return -EINVAL; - /* No information provided by the NAND chip */ if (!req_step || !req_strength) return -ENOTSUPP; @@ -6212,7 +6278,6 @@ int nand_match_ecc_req(struct nand_chip *chip, return 0; } -EXPORT_SYMBOL_GPL(nand_match_ecc_req); /** * nand_maximize_ecc - choose the max ECC strength available @@ -6223,8 +6288,9 @@ EXPORT_SYMBOL_GPL(nand_match_ecc_req); * Choose the max ECC strength that is supported on the controller, and can fit * within the chip's OOB. On success, the chosen ECC settings are set. */ -int nand_maximize_ecc(struct nand_chip *chip, - const struct nand_ecc_caps *caps, int oobavail) +static int +nand_maximize_ecc(struct nand_chip *chip, + const struct nand_ecc_caps *caps, int oobavail) { struct mtd_info *mtd = nand_to_mtd(chip); const struct nand_ecc_step_info *stepinfo; @@ -6234,9 +6300,6 @@ int nand_maximize_ecc(struct nand_chip *chip, int best_strength, best_ecc_bytes; int i, j; - if (WARN_ON(oobavail < 0)) - return -EINVAL; - for (i = 0; i < caps->nstepinfos; i++) { stepinfo = &caps->stepinfos[i]; step_size = stepinfo->stepsize; @@ -6285,7 +6348,44 @@ int nand_maximize_ecc(struct nand_chip *chip, return 0; } -EXPORT_SYMBOL_GPL(nand_maximize_ecc); + +/** + * nand_ecc_choose_conf - Set the ECC strength and ECC step size + * @chip: nand chip info structure + * @caps: ECC engine caps info structure + * @oobavail: OOB size that the ECC engine can use + * + * Choose the ECC configuration according to following logic + * + * 1. If both ECC step size and ECC strength are already set (usually by DT) + * then check if it is supported by this controller. + * 2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength. + * 3. Otherwise, try to match the ECC step size and ECC strength closest + * to the chip's requirement. If available OOB size can't fit the chip + * requirement then fallback to the maximum ECC step size and ECC strength. + * + * On success, the chosen ECC settings are set. + */ +int nand_ecc_choose_conf(struct nand_chip *chip, + const struct nand_ecc_caps *caps, int oobavail) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + if (WARN_ON(oobavail < 0 || oobavail > mtd->oobsize)) + return -EINVAL; + + if (chip->ecc.size && chip->ecc.strength) + return nand_check_ecc_caps(chip, caps, oobavail); + + if (chip->ecc.options & NAND_ECC_MAXIMIZE) + return nand_maximize_ecc(chip, caps, oobavail); + + if (!nand_match_ecc_req(chip, caps, oobavail)) + return 0; + + return nand_maximize_ecc(chip, caps, oobavail); +} +EXPORT_SYMBOL_GPL(nand_ecc_choose_conf); /* * Check if the chip configuration meet the datasheet requirements. @@ -6322,14 +6422,14 @@ static bool nand_ecc_strength_good(struct mtd_info *mtd) } /** - * nand_scan_tail - [NAND Interface] Scan for the NAND device + * nand_scan_tail - Scan for the NAND device * @mtd: MTD device structure * * This is the second phase of the normal nand_scan() function. It fills out * all the uninitialized function pointers with the defaults and scans for a * bad block table if appropriate. */ -int nand_scan_tail(struct mtd_info *mtd) +static int nand_scan_tail(struct mtd_info *mtd) { struct nand_chip *chip = mtd_to_nand(mtd); struct nand_ecc_ctrl *ecc = &chip->ecc; @@ -6636,7 +6736,7 @@ int nand_scan_tail(struct mtd_info *mtd) return 0; /* Build bad block table */ - ret = chip->scan_bbt(mtd); + ret = nand_create_bbt(chip); if (ret) goto err_nand_manuf_cleanup; @@ -6653,24 +6753,27 @@ err_free_buf: return ret; } -EXPORT_SYMBOL(nand_scan_tail); -/* - * is_module_text_address() isn't exported, and it's mostly a pointless - * test if this is a module _anyway_ -- they'd have to try _really_ hard - * to call us from in-kernel code if the core NAND support is modular. - */ -#ifdef MODULE -#define caller_is_module() (1) -#else -#define caller_is_module() \ - is_module_text_address((unsigned long)__builtin_return_address(0)) -#endif +static int nand_attach(struct nand_chip *chip) +{ + if (chip->controller->ops && chip->controller->ops->attach_chip) + return chip->controller->ops->attach_chip(chip); + + return 0; +} + +static void nand_detach(struct nand_chip *chip) +{ + if (chip->controller->ops && chip->controller->ops->detach_chip) + chip->controller->ops->detach_chip(chip); +} /** * nand_scan_with_ids - [NAND Interface] Scan for the NAND device * @mtd: MTD device structure - * @maxchips: number of chips to scan for + * @maxchips: number of chips to scan for. @nand_scan_ident() will not be run if + * this parameter is zero (useful for specific drivers that must + * handle this part of the process themselves, e.g docg4). * @ids: optional flash IDs table * * This fills out all the uninitialized function pointers with the defaults. @@ -6680,11 +6783,30 @@ EXPORT_SYMBOL(nand_scan_tail); int nand_scan_with_ids(struct mtd_info *mtd, int maxchips, struct nand_flash_dev *ids) { + struct nand_chip *chip = mtd_to_nand(mtd); int ret; - ret = nand_scan_ident(mtd, maxchips, ids); - if (!ret) - ret = nand_scan_tail(mtd); + if (maxchips) { + ret = nand_scan_ident(mtd, maxchips, ids); + if (ret) + return ret; + } + + ret = nand_attach(chip); + if (ret) + goto cleanup_ident; + + ret = nand_scan_tail(mtd); + if (ret) + goto detach_chip; + + return 0; + +detach_chip: + nand_detach(chip); +cleanup_ident: + nand_scan_ident_cleanup(chip); + return ret; } EXPORT_SYMBOL(nand_scan_with_ids); @@ -6712,7 +6834,14 @@ void nand_cleanup(struct nand_chip *chip) /* Free manufacturer priv data. */ nand_manufacturer_cleanup(chip); + + /* Free controller specific allocations after chip identification */ + nand_detach(chip); + + /* Free identification phase allocations */ + nand_scan_ident_cleanup(chip); } + EXPORT_SYMBOL_GPL(nand_cleanup); /** diff --git a/drivers/mtd/nand/raw/nand_bbt.c b/drivers/mtd/nand/raw/nand_bbt.c index d9f4ceff2568..39db352f8757 100644 --- a/drivers/mtd/nand/raw/nand_bbt.c +++ b/drivers/mtd/nand/raw/nand_bbt.c @@ -1349,15 +1349,14 @@ static int nand_create_badblock_pattern(struct nand_chip *this) } /** - * nand_default_bbt - [NAND Interface] Select a default bad block table for the device - * @mtd: MTD device structure + * nand_create_bbt - [NAND Interface] Select a default bad block table for the device + * @this: NAND chip object * * This function selects the default bad block table support for the device and * calls the nand_scan_bbt function. */ -int nand_default_bbt(struct mtd_info *mtd) +int nand_create_bbt(struct nand_chip *this) { - struct nand_chip *this = mtd_to_nand(mtd); int ret; /* Is a flash based bad block table requested? */ @@ -1383,8 +1382,9 @@ int nand_default_bbt(struct mtd_info *mtd) return ret; } - return nand_scan_bbt(mtd, this->badblock_pattern); + return nand_scan_bbt(nand_to_mtd(this), this->badblock_pattern); } +EXPORT_SYMBOL(nand_create_bbt); /** * nand_isreserved_bbt - [NAND Interface] Check if a block is reserved diff --git a/drivers/mtd/nand/raw/nand_hynix.c b/drivers/mtd/nand/raw/nand_hynix.c index d542908a0ebb..4ffbb26e76d6 100644 --- a/drivers/mtd/nand/raw/nand_hynix.c +++ b/drivers/mtd/nand/raw/nand_hynix.c @@ -100,6 +100,16 @@ static int hynix_nand_reg_write_op(struct nand_chip *chip, u8 addr, u8 val) struct mtd_info *mtd = nand_to_mtd(chip); u16 column = ((u16)addr << 8) | addr; + if (chip->exec_op) { + struct nand_op_instr instrs[] = { + NAND_OP_ADDR(1, &addr, 0), + NAND_OP_8BIT_DATA_OUT(1, &val, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, NAND_CMD_NONE, column, -1); chip->write_byte(mtd, val); @@ -473,6 +483,19 @@ static void hynix_nand_extract_oobsize(struct nand_chip *chip, WARN(1, "Invalid OOB size"); break; } + + /* + * The datasheet of H27UCG8T2BTR mentions that the "Redundant + * Area Size" is encoded "per 8KB" (page size). This chip uses + * a page size of 16KiB. The datasheet mentions an OOB size of + * 1.280 bytes, but the OOB size encoded in the ID bytes (using + * the existing logic above) is 640 bytes. + * Update the OOB size for this chip by taking the value + * determined above and scaling it to the actual page size (so + * the actual OOB size for this chip is: 640 * 16k / 8k). + */ + if (chip->id.data[1] == 0xde) + mtd->oobsize *= mtd->writesize / SZ_8K; } } diff --git a/drivers/mtd/nand/raw/nand_micron.c b/drivers/mtd/nand/raw/nand_micron.c index 5ec4c90a637d..f5dc0a7a2456 100644 --- a/drivers/mtd/nand/raw/nand_micron.c +++ b/drivers/mtd/nand/raw/nand_micron.c @@ -16,12 +16,33 @@ */ #include <linux/mtd/rawnand.h> +#include <linux/slab.h> /* - * Special Micron status bit that indicates when the block has been - * corrected by on-die ECC and should be rewritten + * Special Micron status bit 3 indicates that the block has been + * corrected by on-die ECC and should be rewritten. */ -#define NAND_STATUS_WRITE_RECOMMENDED BIT(3) +#define NAND_ECC_STATUS_WRITE_RECOMMENDED BIT(3) + +/* + * On chips with 8-bit ECC and additional bit can be used to distinguish + * cases where a errors were corrected without needing a rewrite + * + * Bit 4 Bit 3 Bit 0 Description + * ----- ----- ----- ----------- + * 0 0 0 No Errors + * 0 0 1 Multiple uncorrected errors + * 0 1 0 4 - 6 errors corrected, recommend rewrite + * 0 1 1 Reserved + * 1 0 0 1 - 3 errors corrected + * 1 0 1 Reserved + * 1 1 0 7 - 8 errors corrected, recommend rewrite + */ +#define NAND_ECC_STATUS_MASK (BIT(4) | BIT(3) | BIT(0)) +#define NAND_ECC_STATUS_UNCORRECTABLE BIT(0) +#define NAND_ECC_STATUS_4_6_CORRECTED BIT(3) +#define NAND_ECC_STATUS_1_3_CORRECTED BIT(4) +#define NAND_ECC_STATUS_7_8_CORRECTED (BIT(4) | BIT(3)) struct nand_onfi_vendor_micron { u8 two_plane_read; @@ -43,6 +64,16 @@ struct nand_onfi_vendor_micron { u8 param_revision; } __packed; +struct micron_on_die_ecc { + bool forced; + bool enabled; + void *rawbuf; +}; + +struct micron_nand { + struct micron_on_die_ecc ecc; +}; + static int micron_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) { struct nand_chip *chip = mtd_to_nand(mtd); @@ -57,9 +88,10 @@ static int micron_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) static int micron_nand_onfi_init(struct nand_chip *chip) { struct nand_parameters *p = &chip->parameters; - struct nand_onfi_vendor_micron *micron = (void *)p->onfi.vendor; - if (chip->parameters.onfi.version && p->onfi.vendor_revision) { + if (p->onfi) { + struct nand_onfi_vendor_micron *micron = (void *)p->onfi->vendor; + chip->read_retries = micron->read_retry_options; chip->setup_read_retry = micron_nand_setup_read_retry; } @@ -74,8 +106,9 @@ static int micron_nand_onfi_init(struct nand_chip *chip) return 0; } -static int micron_nand_on_die_ooblayout_ecc(struct mtd_info *mtd, int section, - struct mtd_oob_region *oobregion) +static int micron_nand_on_die_4_ooblayout_ecc(struct mtd_info *mtd, + int section, + struct mtd_oob_region *oobregion) { if (section >= 4) return -ERANGE; @@ -86,8 +119,9 @@ static int micron_nand_on_die_ooblayout_ecc(struct mtd_info *mtd, int section, return 0; } -static int micron_nand_on_die_ooblayout_free(struct mtd_info *mtd, int section, - struct mtd_oob_region *oobregion) +static int micron_nand_on_die_4_ooblayout_free(struct mtd_info *mtd, + int section, + struct mtd_oob_region *oobregion) { if (section >= 4) return -ERANGE; @@ -98,19 +132,161 @@ static int micron_nand_on_die_ooblayout_free(struct mtd_info *mtd, int section, return 0; } -static const struct mtd_ooblayout_ops micron_nand_on_die_ooblayout_ops = { - .ecc = micron_nand_on_die_ooblayout_ecc, - .free = micron_nand_on_die_ooblayout_free, +static const struct mtd_ooblayout_ops micron_nand_on_die_4_ooblayout_ops = { + .ecc = micron_nand_on_die_4_ooblayout_ecc, + .free = micron_nand_on_die_4_ooblayout_free, +}; + +static int micron_nand_on_die_8_ooblayout_ecc(struct mtd_info *mtd, + int section, + struct mtd_oob_region *oobregion) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + + if (section) + return -ERANGE; + + oobregion->offset = mtd->oobsize - chip->ecc.total; + oobregion->length = chip->ecc.total; + + return 0; +} + +static int micron_nand_on_die_8_ooblayout_free(struct mtd_info *mtd, + int section, + struct mtd_oob_region *oobregion) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + + if (section) + return -ERANGE; + + oobregion->offset = 2; + oobregion->length = mtd->oobsize - chip->ecc.total - 2; + + return 0; +} + +static const struct mtd_ooblayout_ops micron_nand_on_die_8_ooblayout_ops = { + .ecc = micron_nand_on_die_8_ooblayout_ecc, + .free = micron_nand_on_die_8_ooblayout_free, }; static int micron_nand_on_die_ecc_setup(struct nand_chip *chip, bool enable) { + struct micron_nand *micron = nand_get_manufacturer_data(chip); u8 feature[ONFI_SUBFEATURE_PARAM_LEN] = { 0, }; + int ret; + + if (micron->ecc.forced) + return 0; + + if (micron->ecc.enabled == enable) + return 0; if (enable) feature[0] |= ONFI_FEATURE_ON_DIE_ECC_EN; - return nand_set_features(chip, ONFI_FEATURE_ON_DIE_ECC, feature); + ret = nand_set_features(chip, ONFI_FEATURE_ON_DIE_ECC, feature); + if (!ret) + micron->ecc.enabled = enable; + + return ret; +} + +static int micron_nand_on_die_ecc_status_4(struct nand_chip *chip, u8 status, + void *buf, int page, + int oob_required) +{ + struct micron_nand *micron = nand_get_manufacturer_data(chip); + struct mtd_info *mtd = nand_to_mtd(chip); + unsigned int step, max_bitflips = 0; + int ret; + + if (!(status & NAND_ECC_STATUS_WRITE_RECOMMENDED)) { + if (status & NAND_STATUS_FAIL) + mtd->ecc_stats.failed++; + + return 0; + } + + /* + * The internal ECC doesn't tell us the number of bitflips that have + * been corrected, but tells us if it recommends to rewrite the block. + * If it's the case, we need to read the page in raw mode and compare + * its content to the corrected version to extract the actual number of + * bitflips. + * But before we do that, we must make sure we have all OOB bytes read + * in non-raw mode, even if the user did not request those bytes. + */ + if (!oob_required) { + ret = nand_read_data_op(chip, chip->oob_poi, mtd->oobsize, + false); + if (ret) + return ret; + } + + micron_nand_on_die_ecc_setup(chip, false); + + ret = nand_read_page_op(chip, page, 0, micron->ecc.rawbuf, + mtd->writesize + mtd->oobsize); + if (ret) + return ret; + + for (step = 0; step < chip->ecc.steps; step++) { + unsigned int offs, i, nbitflips = 0; + u8 *rawbuf, *corrbuf; + + offs = step * chip->ecc.size; + rawbuf = micron->ecc.rawbuf + offs; + corrbuf = buf + offs; + + for (i = 0; i < chip->ecc.size; i++) + nbitflips += hweight8(corrbuf[i] ^ rawbuf[i]); + + offs = (step * 16) + 4; + rawbuf = micron->ecc.rawbuf + mtd->writesize + offs; + corrbuf = chip->oob_poi + offs; + + for (i = 0; i < chip->ecc.bytes + 4; i++) + nbitflips += hweight8(corrbuf[i] ^ rawbuf[i]); + + if (WARN_ON(nbitflips > chip->ecc.strength)) + return -EINVAL; + + max_bitflips = max(nbitflips, max_bitflips); + mtd->ecc_stats.corrected += nbitflips; + } + + return max_bitflips; +} + +static int micron_nand_on_die_ecc_status_8(struct nand_chip *chip, u8 status) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + /* + * With 8/512 we have more information but still don't know precisely + * how many bit-flips were seen. + */ + switch (status & NAND_ECC_STATUS_MASK) { + case NAND_ECC_STATUS_UNCORRECTABLE: + mtd->ecc_stats.failed++; + return 0; + case NAND_ECC_STATUS_1_3_CORRECTED: + mtd->ecc_stats.corrected += 3; + return 3; + case NAND_ECC_STATUS_4_6_CORRECTED: + mtd->ecc_stats.corrected += 6; + /* rewrite recommended */ + return 6; + case NAND_ECC_STATUS_7_8_CORRECTED: + mtd->ecc_stats.corrected += 8; + /* rewrite recommended */ + return 8; + default: + return 0; + } } static int @@ -137,24 +313,18 @@ micron_nand_read_page_on_die_ecc(struct mtd_info *mtd, struct nand_chip *chip, if (ret) goto out; - if (status & NAND_STATUS_FAIL) - mtd->ecc_stats.failed++; - - /* - * The internal ECC doesn't tell us the number of bitflips - * that have been corrected, but tells us if it recommends to - * rewrite the block. If it's the case, then we pretend we had - * a number of bitflips equal to the ECC strength, which will - * hint the NAND core to rewrite the block. - */ - else if (status & NAND_STATUS_WRITE_RECOMMENDED) - max_bitflips = chip->ecc.strength; - ret = nand_read_data_op(chip, buf, mtd->writesize, false); if (!ret && oob_required) ret = nand_read_data_op(chip, chip->oob_poi, mtd->oobsize, false); + if (chip->ecc.strength == 4) + max_bitflips = micron_nand_on_die_ecc_status_4(chip, status, + buf, page, + oob_required); + else + max_bitflips = micron_nand_on_die_ecc_status_8(chip, status); + out: micron_nand_on_die_ecc_setup(chip, false); @@ -195,6 +365,9 @@ enum { MICRON_ON_DIE_MANDATORY, }; +#define MICRON_ID_INTERNAL_ECC_MASK GENMASK(1, 0) +#define MICRON_ID_ECC_ENABLED BIT(7) + /* * Try to detect if the NAND support on-die ECC. To do this, we enable * the feature, and read back if it has been enabled as expected. We @@ -207,42 +380,52 @@ enum { */ static int micron_supports_on_die_ecc(struct nand_chip *chip) { - u8 feature[ONFI_SUBFEATURE_PARAM_LEN] = { 0, }; + u8 id[5]; int ret; - if (!chip->parameters.onfi.version) + if (!chip->parameters.onfi) return MICRON_ON_DIE_UNSUPPORTED; if (chip->bits_per_cell != 1) return MICRON_ON_DIE_UNSUPPORTED; + /* + * We only support on-die ECC of 4/512 or 8/512 + */ + if (chip->ecc_strength_ds != 4 && chip->ecc_strength_ds != 8) + return MICRON_ON_DIE_UNSUPPORTED; + + /* 0x2 means on-die ECC is available. */ + if (chip->id.len != 5 || + (chip->id.data[4] & MICRON_ID_INTERNAL_ECC_MASK) != 0x2) + return MICRON_ON_DIE_UNSUPPORTED; + ret = micron_nand_on_die_ecc_setup(chip, true); if (ret) return MICRON_ON_DIE_UNSUPPORTED; - ret = nand_get_features(chip, ONFI_FEATURE_ON_DIE_ECC, feature); - if (ret < 0) - return ret; + ret = nand_readid_op(chip, 0, id, sizeof(id)); + if (ret) + return MICRON_ON_DIE_UNSUPPORTED; - if ((feature[0] & ONFI_FEATURE_ON_DIE_ECC_EN) == 0) + if (!(id[4] & MICRON_ID_ECC_ENABLED)) return MICRON_ON_DIE_UNSUPPORTED; ret = micron_nand_on_die_ecc_setup(chip, false); if (ret) return MICRON_ON_DIE_UNSUPPORTED; - ret = nand_get_features(chip, ONFI_FEATURE_ON_DIE_ECC, feature); - if (ret < 0) - return ret; + ret = nand_readid_op(chip, 0, id, sizeof(id)); + if (ret) + return MICRON_ON_DIE_UNSUPPORTED; - if (feature[0] & ONFI_FEATURE_ON_DIE_ECC_EN) + if (id[4] & MICRON_ID_ECC_ENABLED) return MICRON_ON_DIE_MANDATORY; /* - * Some Micron NANDs have an on-die ECC of 4/512, some other - * 8/512. We only support the former. + * We only support on-die ECC of 4/512 or 8/512 */ - if (chip->ecc_strength_ds != 4) + if (chip->ecc_strength_ds != 4 && chip->ecc_strength_ds != 8) return MICRON_ON_DIE_UNSUPPORTED; return MICRON_ON_DIE_SUPPORTED; @@ -251,44 +434,116 @@ static int micron_supports_on_die_ecc(struct nand_chip *chip) static int micron_nand_init(struct nand_chip *chip) { struct mtd_info *mtd = nand_to_mtd(chip); + struct micron_nand *micron; int ondie; int ret; + micron = kzalloc(sizeof(*micron), GFP_KERNEL); + if (!micron) + return -ENOMEM; + + nand_set_manufacturer_data(chip, micron); + ret = micron_nand_onfi_init(chip); if (ret) - return ret; + goto err_free_manuf_data; if (mtd->writesize == 2048) chip->bbt_options |= NAND_BBT_SCAN2NDPAGE; ondie = micron_supports_on_die_ecc(chip); - if (ondie == MICRON_ON_DIE_MANDATORY) { + if (ondie == MICRON_ON_DIE_MANDATORY && + chip->ecc.mode != NAND_ECC_ON_DIE) { pr_err("On-die ECC forcefully enabled, not supported\n"); - return -EINVAL; + ret = -EINVAL; + goto err_free_manuf_data; } if (chip->ecc.mode == NAND_ECC_ON_DIE) { if (ondie == MICRON_ON_DIE_UNSUPPORTED) { pr_err("On-die ECC selected but not supported\n"); - return -EINVAL; + ret = -EINVAL; + goto err_free_manuf_data; + } + + if (ondie == MICRON_ON_DIE_MANDATORY) { + micron->ecc.forced = true; + micron->ecc.enabled = true; + } + + /* + * In case of 4bit on-die ECC, we need a buffer to store a + * page dumped in raw mode so that we can compare its content + * to the same page after ECC correction happened and extract + * the real number of bitflips from this comparison. + * That's not needed for 8-bit ECC, because the status expose + * a better approximation of the number of bitflips in a page. + */ + if (chip->ecc_strength_ds == 4) { + micron->ecc.rawbuf = kmalloc(mtd->writesize + + mtd->oobsize, + GFP_KERNEL); + if (!micron->ecc.rawbuf) { + ret = -ENOMEM; + goto err_free_manuf_data; + } } - chip->ecc.bytes = 8; + if (chip->ecc_strength_ds == 4) + mtd_set_ooblayout(mtd, + µn_nand_on_die_4_ooblayout_ops); + else + mtd_set_ooblayout(mtd, + µn_nand_on_die_8_ooblayout_ops); + + chip->ecc.bytes = chip->ecc_strength_ds * 2; chip->ecc.size = 512; - chip->ecc.strength = 4; + chip->ecc.strength = chip->ecc_strength_ds; chip->ecc.algo = NAND_ECC_BCH; chip->ecc.read_page = micron_nand_read_page_on_die_ecc; chip->ecc.write_page = micron_nand_write_page_on_die_ecc; - chip->ecc.read_page_raw = nand_read_page_raw; - chip->ecc.write_page_raw = nand_write_page_raw; - mtd_set_ooblayout(mtd, µn_nand_on_die_ooblayout_ops); + if (ondie == MICRON_ON_DIE_MANDATORY) { + chip->ecc.read_page_raw = nand_read_page_raw_notsupp; + chip->ecc.write_page_raw = nand_write_page_raw_notsupp; + } else { + chip->ecc.read_page_raw = nand_read_page_raw; + chip->ecc.write_page_raw = nand_write_page_raw; + } } return 0; + +err_free_manuf_data: + kfree(micron->ecc.rawbuf); + kfree(micron); + + return ret; +} + +static void micron_nand_cleanup(struct nand_chip *chip) +{ + struct micron_nand *micron = nand_get_manufacturer_data(chip); + + kfree(micron->ecc.rawbuf); + kfree(micron); +} + +static void micron_fixup_onfi_param_page(struct nand_chip *chip, + struct nand_onfi_params *p) +{ + /* + * MT29F1G08ABAFAWP-ITE:F and possibly others report 00 00 for the + * revision number field of the ONFI parameter page. Assume ONFI + * version 1.0 if the revision number is 00 00. + */ + if (le16_to_cpu(p->revision) == 0) + p->revision = cpu_to_le16(ONFI_VERSION_1_0); } const struct nand_manufacturer_ops micron_nand_manuf_ops = { .init = micron_nand_init, + .cleanup = micron_nand_cleanup, + .fixup_onfi_param_page = micron_fixup_onfi_param_page, }; diff --git a/drivers/mtd/nand/raw/nand_timings.c b/drivers/mtd/nand/raw/nand_timings.c index 7c4e4a371bbc..ebc7b5f76f77 100644 --- a/drivers/mtd/nand/raw/nand_timings.c +++ b/drivers/mtd/nand/raw/nand_timings.c @@ -13,6 +13,8 @@ #include <linux/export.h> #include <linux/mtd/rawnand.h> +#define ONFI_DYN_TIMING_MAX U16_MAX + static const struct nand_data_interface onfi_sdr_timings[] = { /* Mode 0 */ { @@ -292,6 +294,7 @@ int onfi_fill_data_interface(struct nand_chip *chip, int timing_mode) { struct nand_data_interface *iface = &chip->data_interface; + struct onfi_params *onfi = chip->parameters.onfi; if (type != NAND_SDR_IFACE) return -EINVAL; @@ -303,20 +306,35 @@ int onfi_fill_data_interface(struct nand_chip *chip, /* * Initialize timings that cannot be deduced from timing mode: - * tR, tPROG, tCCS, ... + * tPROG, tBERS, tR and tCCS. * These information are part of the ONFI parameter page. */ - if (chip->parameters.onfi.version) { - struct nand_parameters *params = &chip->parameters; + if (onfi) { + struct nand_sdr_timings *timings = &iface->timings.sdr; + + /* microseconds -> picoseconds */ + timings->tPROG_max = 1000000ULL * onfi->tPROG; + timings->tBERS_max = 1000000ULL * onfi->tBERS; + timings->tR_max = 1000000ULL * onfi->tR; + + /* nanoseconds -> picoseconds */ + timings->tCCS_min = 1000UL * onfi->tCCS; + } else { struct nand_sdr_timings *timings = &iface->timings.sdr; + /* + * For non-ONFI chips we use the highest possible value for + * tPROG and tBERS. tR and tCCS will take the default values + * precised in the ONFI specification for timing mode 0, + * respectively 200us and 500ns. + */ /* microseconds -> picoseconds */ - timings->tPROG_max = 1000000ULL * params->onfi.tPROG; - timings->tBERS_max = 1000000ULL * params->onfi.tBERS; - timings->tR_max = 1000000ULL * params->onfi.tR; + timings->tPROG_max = 1000000ULL * ONFI_DYN_TIMING_MAX; + timings->tBERS_max = 1000000ULL * ONFI_DYN_TIMING_MAX; + timings->tR_max = 1000000ULL * 200000000ULL; /* nanoseconds -> picoseconds */ - timings->tCCS_min = 1000UL * params->onfi.tCCS; + timings->tCCS_min = 1000UL * 500000; } return 0; diff --git a/drivers/mtd/nand/raw/nandsim.c b/drivers/mtd/nand/raw/nandsim.c index f8edacde49ab..71ac034aee9c 100644 --- a/drivers/mtd/nand/raw/nandsim.c +++ b/drivers/mtd/nand/raw/nandsim.c @@ -2192,6 +2192,48 @@ static void ns_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len) return; } +static int ns_attach_chip(struct nand_chip *chip) +{ + unsigned int eccsteps, eccbytes; + + if (!bch) + return 0; + + if (!mtd_nand_has_bch()) { + NS_ERR("BCH ECC support is disabled\n"); + return -EINVAL; + } + + /* Use 512-byte ecc blocks */ + eccsteps = nsmtd->writesize / 512; + eccbytes = ((bch * 13) + 7) / 8; + + /* Do not bother supporting small page devices */ + if (nsmtd->oobsize < 64 || !eccsteps) { + NS_ERR("BCH not available on small page devices\n"); + return -EINVAL; + } + + if (((eccbytes * eccsteps) + 2) > nsmtd->oobsize) { + NS_ERR("Invalid BCH value %u\n", bch); + return -EINVAL; + } + + chip->ecc.mode = NAND_ECC_SOFT; + chip->ecc.algo = NAND_ECC_BCH; + chip->ecc.size = 512; + chip->ecc.strength = bch; + chip->ecc.bytes = eccbytes; + + NS_INFO("Using %u-bit/%u bytes BCH ECC\n", bch, chip->ecc.size); + + return 0; +} + +static const struct nand_controller_ops ns_controller_ops = { + .attach_chip = ns_attach_chip, +}; + /* * Module initialization function */ @@ -2276,44 +2318,10 @@ static int __init ns_init_module(void) if ((retval = parse_gravepages()) != 0) goto error; - retval = nand_scan_ident(nsmtd, 1, NULL); - if (retval) { - NS_ERR("cannot scan NAND Simulator device\n"); - goto error; - } - - if (bch) { - unsigned int eccsteps, eccbytes; - if (!mtd_nand_has_bch()) { - NS_ERR("BCH ECC support is disabled\n"); - retval = -EINVAL; - goto error; - } - /* use 512-byte ecc blocks */ - eccsteps = nsmtd->writesize/512; - eccbytes = (bch*13+7)/8; - /* do not bother supporting small page devices */ - if ((nsmtd->oobsize < 64) || !eccsteps) { - NS_ERR("bch not available on small page devices\n"); - retval = -EINVAL; - goto error; - } - if ((eccbytes*eccsteps+2) > nsmtd->oobsize) { - NS_ERR("invalid bch value %u\n", bch); - retval = -EINVAL; - goto error; - } - chip->ecc.mode = NAND_ECC_SOFT; - chip->ecc.algo = NAND_ECC_BCH; - chip->ecc.size = 512; - chip->ecc.strength = bch; - chip->ecc.bytes = eccbytes; - NS_INFO("using %u-bit/%u bytes BCH ECC\n", bch, chip->ecc.size); - } - - retval = nand_scan_tail(nsmtd); + chip->dummy_controller.ops = &ns_controller_ops; + retval = nand_scan(nsmtd, 1); if (retval) { - NS_ERR("can't register NAND Simulator\n"); + NS_ERR("Could not scan NAND Simulator device\n"); goto error; } @@ -2337,7 +2345,7 @@ static int __init ns_init_module(void) if ((retval = init_nandsim(nsmtd)) != 0) goto err_exit; - if ((retval = chip->scan_bbt(nsmtd)) != 0) + if ((retval = nand_create_bbt(chip)) != 0) goto err_exit; if ((retval = parse_badblocks(nand, nsmtd)) != 0) diff --git a/drivers/mtd/nand/raw/ndfc.c b/drivers/mtd/nand/raw/ndfc.c index d8a806894937..540fa1a0ea24 100644 --- a/drivers/mtd/nand/raw/ndfc.c +++ b/drivers/mtd/nand/raw/ndfc.c @@ -39,7 +39,7 @@ struct ndfc_controller { void __iomem *ndfcbase; struct nand_chip chip; int chip_select; - struct nand_hw_control ndfc_control; + struct nand_controller ndfc_control; }; static struct ndfc_controller ndfc_ctrl[NDFC_MAX_CS]; @@ -218,7 +218,7 @@ static int ndfc_probe(struct platform_device *ofdev) ndfc = &ndfc_ctrl[cs]; ndfc->chip_select = cs; - nand_hw_control_init(&ndfc->ndfc_control); + nand_controller_init(&ndfc->ndfc_control); ndfc->ofdev = ofdev; dev_set_drvdata(&ofdev->dev, ndfc); diff --git a/drivers/mtd/nand/raw/omap2.c b/drivers/mtd/nand/raw/omap2.c index e50c64adc3c8..4546ac0bed4a 100644 --- a/drivers/mtd/nand/raw/omap2.c +++ b/drivers/mtd/nand/raw/omap2.c @@ -144,12 +144,6 @@ static u_char bch8_vector[] = {0xf3, 0xdb, 0x14, 0x16, 0x8b, 0xd2, 0xbe, 0xcc, 0xac, 0x6b, 0xff, 0x99, 0x7b}; static u_char bch4_vector[] = {0x00, 0x6b, 0x31, 0xdd, 0x41, 0xbc, 0x10}; -/* Shared among all NAND instances to synchronize access to the ECC Engine */ -static struct nand_hw_control omap_gpmc_controller = { - .lock = __SPIN_LOCK_UNLOCKED(omap_gpmc_controller.lock), - .wq = __WAIT_QUEUE_HEAD_INITIALIZER(omap_gpmc_controller.wq), -}; - struct omap_nand_info { struct nand_chip nand; struct platform_device *pdev; @@ -1915,106 +1909,26 @@ static const struct mtd_ooblayout_ops omap_sw_ooblayout_ops = { .free = omap_sw_ooblayout_free, }; -static int omap_nand_probe(struct platform_device *pdev) +static int omap_nand_attach_chip(struct nand_chip *chip) { - struct omap_nand_info *info; - struct mtd_info *mtd; - struct nand_chip *nand_chip; - int err; - dma_cap_mask_t mask; - struct resource *res; - struct device *dev = &pdev->dev; - int min_oobbytes = BADBLOCK_MARKER_LENGTH; - int oobbytes_per_step; - - info = devm_kzalloc(&pdev->dev, sizeof(struct omap_nand_info), - GFP_KERNEL); - if (!info) - return -ENOMEM; - - info->pdev = pdev; - - err = omap_get_dt_info(dev, info); - if (err) - return err; - - info->ops = gpmc_omap_get_nand_ops(&info->reg, info->gpmc_cs); - if (!info->ops) { - dev_err(&pdev->dev, "Failed to get GPMC->NAND interface\n"); - return -ENODEV; - } - - nand_chip = &info->nand; - mtd = nand_to_mtd(nand_chip); - mtd->dev.parent = &pdev->dev; - nand_chip->ecc.priv = NULL; - nand_set_flash_node(nand_chip, dev->of_node); - - if (!mtd->name) { - mtd->name = devm_kasprintf(&pdev->dev, GFP_KERNEL, - "omap2-nand.%d", info->gpmc_cs); - if (!mtd->name) { - dev_err(&pdev->dev, "Failed to set MTD name\n"); - return -ENOMEM; - } - } - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - nand_chip->IO_ADDR_R = devm_ioremap_resource(&pdev->dev, res); - if (IS_ERR(nand_chip->IO_ADDR_R)) - return PTR_ERR(nand_chip->IO_ADDR_R); - - info->phys_base = res->start; - - nand_chip->controller = &omap_gpmc_controller; - - nand_chip->IO_ADDR_W = nand_chip->IO_ADDR_R; - nand_chip->cmd_ctrl = omap_hwcontrol; - - info->ready_gpiod = devm_gpiod_get_optional(&pdev->dev, "rb", - GPIOD_IN); - if (IS_ERR(info->ready_gpiod)) { - dev_err(dev, "failed to get ready gpio\n"); - return PTR_ERR(info->ready_gpiod); - } - - /* - * If RDY/BSY line is connected to OMAP then use the omap ready - * function and the generic nand_wait function which reads the status - * register after monitoring the RDY/BSY line. Otherwise use a standard - * chip delay which is slightly more than tR (AC Timing) of the NAND - * device and read status register until you get a failure or success - */ - if (info->ready_gpiod) { - nand_chip->dev_ready = omap_dev_ready; - nand_chip->chip_delay = 0; - } else { - nand_chip->waitfunc = omap_wait; - nand_chip->chip_delay = 50; - } - - if (info->flash_bbt) - nand_chip->bbt_options |= NAND_BBT_USE_FLASH; - - /* scan NAND device connected to chip controller */ - nand_chip->options |= info->devsize & NAND_BUSWIDTH_16; - err = nand_scan_ident(mtd, 1, NULL); - if (err) { - dev_err(&info->pdev->dev, - "scan failed, may be bus-width mismatch\n"); - goto return_error; - } + struct mtd_info *mtd = nand_to_mtd(chip); + struct omap_nand_info *info = mtd_to_omap(mtd); + struct device *dev = &info->pdev->dev; + int min_oobbytes = BADBLOCK_MARKER_LENGTH; + int oobbytes_per_step; + dma_cap_mask_t mask; + int err; - if (nand_chip->bbt_options & NAND_BBT_USE_FLASH) - nand_chip->bbt_options |= NAND_BBT_NO_OOB; + if (chip->bbt_options & NAND_BBT_USE_FLASH) + chip->bbt_options |= NAND_BBT_NO_OOB; else - nand_chip->options |= NAND_SKIP_BBTSCAN; + chip->options |= NAND_SKIP_BBTSCAN; - /* re-populate low-level callbacks based on xfer modes */ + /* Re-populate low-level callbacks based on xfer modes */ switch (info->xfer_type) { case NAND_OMAP_PREFETCH_POLLED: - nand_chip->read_buf = omap_read_buf_pref; - nand_chip->write_buf = omap_write_buf_pref; + chip->read_buf = omap_read_buf_pref; + chip->write_buf = omap_write_buf_pref; break; case NAND_OMAP_POLLED: @@ -2024,12 +1938,11 @@ static int omap_nand_probe(struct platform_device *pdev) case NAND_OMAP_PREFETCH_DMA: dma_cap_zero(mask); dma_cap_set(DMA_SLAVE, mask); - info->dma = dma_request_chan(pdev->dev.parent, "rxtx"); + info->dma = dma_request_chan(dev, "rxtx"); if (IS_ERR(info->dma)) { - dev_err(&pdev->dev, "DMA engine request failed\n"); - err = PTR_ERR(info->dma); - goto return_error; + dev_err(dev, "DMA engine request failed\n"); + return PTR_ERR(info->dma); } else { struct dma_slave_config cfg; @@ -2042,222 +1955,306 @@ static int omap_nand_probe(struct platform_device *pdev) cfg.dst_maxburst = 16; err = dmaengine_slave_config(info->dma, &cfg); if (err) { - dev_err(&pdev->dev, "DMA engine slave config failed: %d\n", + dev_err(dev, + "DMA engine slave config failed: %d\n", err); - goto return_error; + return err; } - nand_chip->read_buf = omap_read_buf_dma_pref; - nand_chip->write_buf = omap_write_buf_dma_pref; + chip->read_buf = omap_read_buf_dma_pref; + chip->write_buf = omap_write_buf_dma_pref; } break; case NAND_OMAP_PREFETCH_IRQ: - info->gpmc_irq_fifo = platform_get_irq(pdev, 0); + info->gpmc_irq_fifo = platform_get_irq(info->pdev, 0); if (info->gpmc_irq_fifo <= 0) { - dev_err(&pdev->dev, "error getting fifo irq\n"); - err = -ENODEV; - goto return_error; + dev_err(dev, "Error getting fifo IRQ\n"); + return -ENODEV; } - err = devm_request_irq(&pdev->dev, info->gpmc_irq_fifo, - omap_nand_irq, IRQF_SHARED, - "gpmc-nand-fifo", info); + err = devm_request_irq(dev, info->gpmc_irq_fifo, + omap_nand_irq, IRQF_SHARED, + "gpmc-nand-fifo", info); if (err) { - dev_err(&pdev->dev, "requesting irq(%d) error:%d", - info->gpmc_irq_fifo, err); + dev_err(dev, "Requesting IRQ %d, error %d\n", + info->gpmc_irq_fifo, err); info->gpmc_irq_fifo = 0; - goto return_error; + return err; } - info->gpmc_irq_count = platform_get_irq(pdev, 1); + info->gpmc_irq_count = platform_get_irq(info->pdev, 1); if (info->gpmc_irq_count <= 0) { - dev_err(&pdev->dev, "error getting count irq\n"); - err = -ENODEV; - goto return_error; + dev_err(dev, "Error getting IRQ count\n"); + return -ENODEV; } - err = devm_request_irq(&pdev->dev, info->gpmc_irq_count, - omap_nand_irq, IRQF_SHARED, - "gpmc-nand-count", info); + err = devm_request_irq(dev, info->gpmc_irq_count, + omap_nand_irq, IRQF_SHARED, + "gpmc-nand-count", info); if (err) { - dev_err(&pdev->dev, "requesting irq(%d) error:%d", - info->gpmc_irq_count, err); + dev_err(dev, "Requesting IRQ %d, error %d\n", + info->gpmc_irq_count, err); info->gpmc_irq_count = 0; - goto return_error; + return err; } - nand_chip->read_buf = omap_read_buf_irq_pref; - nand_chip->write_buf = omap_write_buf_irq_pref; + chip->read_buf = omap_read_buf_irq_pref; + chip->write_buf = omap_write_buf_irq_pref; break; default: - dev_err(&pdev->dev, - "xfer_type(%d) not supported!\n", info->xfer_type); - err = -EINVAL; - goto return_error; + dev_err(dev, "xfer_type %d not supported!\n", info->xfer_type); + return -EINVAL; } - if (!omap2_nand_ecc_check(info)) { - err = -EINVAL; - goto return_error; - } + if (!omap2_nand_ecc_check(info)) + return -EINVAL; /* * Bail out earlier to let NAND_ECC_SOFT code create its own * ooblayout instead of using ours. */ if (info->ecc_opt == OMAP_ECC_HAM1_CODE_SW) { - nand_chip->ecc.mode = NAND_ECC_SOFT; - nand_chip->ecc.algo = NAND_ECC_HAMMING; - goto scan_tail; + chip->ecc.mode = NAND_ECC_SOFT; + chip->ecc.algo = NAND_ECC_HAMMING; + return 0; } - /* populate MTD interface based on ECC scheme */ + /* Populate MTD interface based on ECC scheme */ switch (info->ecc_opt) { case OMAP_ECC_HAM1_CODE_HW: - pr_info("nand: using OMAP_ECC_HAM1_CODE_HW\n"); - nand_chip->ecc.mode = NAND_ECC_HW; - nand_chip->ecc.bytes = 3; - nand_chip->ecc.size = 512; - nand_chip->ecc.strength = 1; - nand_chip->ecc.calculate = omap_calculate_ecc; - nand_chip->ecc.hwctl = omap_enable_hwecc; - nand_chip->ecc.correct = omap_correct_data; + dev_info(dev, "nand: using OMAP_ECC_HAM1_CODE_HW\n"); + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.bytes = 3; + chip->ecc.size = 512; + chip->ecc.strength = 1; + chip->ecc.calculate = omap_calculate_ecc; + chip->ecc.hwctl = omap_enable_hwecc; + chip->ecc.correct = omap_correct_data; mtd_set_ooblayout(mtd, &omap_ooblayout_ops); - oobbytes_per_step = nand_chip->ecc.bytes; + oobbytes_per_step = chip->ecc.bytes; - if (!(nand_chip->options & NAND_BUSWIDTH_16)) - min_oobbytes = 1; + if (!(chip->options & NAND_BUSWIDTH_16)) + min_oobbytes = 1; break; case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW: pr_info("nand: using OMAP_ECC_BCH4_CODE_HW_DETECTION_SW\n"); - nand_chip->ecc.mode = NAND_ECC_HW; - nand_chip->ecc.size = 512; - nand_chip->ecc.bytes = 7; - nand_chip->ecc.strength = 4; - nand_chip->ecc.hwctl = omap_enable_hwecc_bch; - nand_chip->ecc.correct = nand_bch_correct_data; - nand_chip->ecc.calculate = omap_calculate_ecc_bch_sw; + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.size = 512; + chip->ecc.bytes = 7; + chip->ecc.strength = 4; + chip->ecc.hwctl = omap_enable_hwecc_bch; + chip->ecc.correct = nand_bch_correct_data; + chip->ecc.calculate = omap_calculate_ecc_bch_sw; mtd_set_ooblayout(mtd, &omap_sw_ooblayout_ops); /* Reserve one byte for the OMAP marker */ - oobbytes_per_step = nand_chip->ecc.bytes + 1; - /* software bch library is used for locating errors */ - nand_chip->ecc.priv = nand_bch_init(mtd); - if (!nand_chip->ecc.priv) { - dev_err(&info->pdev->dev, "unable to use BCH library\n"); - err = -EINVAL; - goto return_error; + oobbytes_per_step = chip->ecc.bytes + 1; + /* Software BCH library is used for locating errors */ + chip->ecc.priv = nand_bch_init(mtd); + if (!chip->ecc.priv) { + dev_err(dev, "Unable to use BCH library\n"); + return -EINVAL; } break; case OMAP_ECC_BCH4_CODE_HW: pr_info("nand: using OMAP_ECC_BCH4_CODE_HW ECC scheme\n"); - nand_chip->ecc.mode = NAND_ECC_HW; - nand_chip->ecc.size = 512; + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.size = 512; /* 14th bit is kept reserved for ROM-code compatibility */ - nand_chip->ecc.bytes = 7 + 1; - nand_chip->ecc.strength = 4; - nand_chip->ecc.hwctl = omap_enable_hwecc_bch; - nand_chip->ecc.correct = omap_elm_correct_data; - nand_chip->ecc.read_page = omap_read_page_bch; - nand_chip->ecc.write_page = omap_write_page_bch; - nand_chip->ecc.write_subpage = omap_write_subpage_bch; + chip->ecc.bytes = 7 + 1; + chip->ecc.strength = 4; + chip->ecc.hwctl = omap_enable_hwecc_bch; + chip->ecc.correct = omap_elm_correct_data; + chip->ecc.read_page = omap_read_page_bch; + chip->ecc.write_page = omap_write_page_bch; + chip->ecc.write_subpage = omap_write_subpage_bch; mtd_set_ooblayout(mtd, &omap_ooblayout_ops); - oobbytes_per_step = nand_chip->ecc.bytes; + oobbytes_per_step = chip->ecc.bytes; err = elm_config(info->elm_dev, BCH4_ECC, - mtd->writesize / nand_chip->ecc.size, - nand_chip->ecc.size, nand_chip->ecc.bytes); + mtd->writesize / chip->ecc.size, + chip->ecc.size, chip->ecc.bytes); if (err < 0) - goto return_error; + return err; break; case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW: pr_info("nand: using OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n"); - nand_chip->ecc.mode = NAND_ECC_HW; - nand_chip->ecc.size = 512; - nand_chip->ecc.bytes = 13; - nand_chip->ecc.strength = 8; - nand_chip->ecc.hwctl = omap_enable_hwecc_bch; - nand_chip->ecc.correct = nand_bch_correct_data; - nand_chip->ecc.calculate = omap_calculate_ecc_bch_sw; + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.size = 512; + chip->ecc.bytes = 13; + chip->ecc.strength = 8; + chip->ecc.hwctl = omap_enable_hwecc_bch; + chip->ecc.correct = nand_bch_correct_data; + chip->ecc.calculate = omap_calculate_ecc_bch_sw; mtd_set_ooblayout(mtd, &omap_sw_ooblayout_ops); /* Reserve one byte for the OMAP marker */ - oobbytes_per_step = nand_chip->ecc.bytes + 1; - /* software bch library is used for locating errors */ - nand_chip->ecc.priv = nand_bch_init(mtd); - if (!nand_chip->ecc.priv) { - dev_err(&info->pdev->dev, "unable to use BCH library\n"); - err = -EINVAL; - goto return_error; + oobbytes_per_step = chip->ecc.bytes + 1; + /* Software BCH library is used for locating errors */ + chip->ecc.priv = nand_bch_init(mtd); + if (!chip->ecc.priv) { + dev_err(dev, "unable to use BCH library\n"); + return -EINVAL; } break; case OMAP_ECC_BCH8_CODE_HW: pr_info("nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme\n"); - nand_chip->ecc.mode = NAND_ECC_HW; - nand_chip->ecc.size = 512; + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.size = 512; /* 14th bit is kept reserved for ROM-code compatibility */ - nand_chip->ecc.bytes = 13 + 1; - nand_chip->ecc.strength = 8; - nand_chip->ecc.hwctl = omap_enable_hwecc_bch; - nand_chip->ecc.correct = omap_elm_correct_data; - nand_chip->ecc.read_page = omap_read_page_bch; - nand_chip->ecc.write_page = omap_write_page_bch; - nand_chip->ecc.write_subpage = omap_write_subpage_bch; + chip->ecc.bytes = 13 + 1; + chip->ecc.strength = 8; + chip->ecc.hwctl = omap_enable_hwecc_bch; + chip->ecc.correct = omap_elm_correct_data; + chip->ecc.read_page = omap_read_page_bch; + chip->ecc.write_page = omap_write_page_bch; + chip->ecc.write_subpage = omap_write_subpage_bch; mtd_set_ooblayout(mtd, &omap_ooblayout_ops); - oobbytes_per_step = nand_chip->ecc.bytes; + oobbytes_per_step = chip->ecc.bytes; err = elm_config(info->elm_dev, BCH8_ECC, - mtd->writesize / nand_chip->ecc.size, - nand_chip->ecc.size, nand_chip->ecc.bytes); + mtd->writesize / chip->ecc.size, + chip->ecc.size, chip->ecc.bytes); if (err < 0) - goto return_error; + return err; break; case OMAP_ECC_BCH16_CODE_HW: - pr_info("using OMAP_ECC_BCH16_CODE_HW ECC scheme\n"); - nand_chip->ecc.mode = NAND_ECC_HW; - nand_chip->ecc.size = 512; - nand_chip->ecc.bytes = 26; - nand_chip->ecc.strength = 16; - nand_chip->ecc.hwctl = omap_enable_hwecc_bch; - nand_chip->ecc.correct = omap_elm_correct_data; - nand_chip->ecc.read_page = omap_read_page_bch; - nand_chip->ecc.write_page = omap_write_page_bch; - nand_chip->ecc.write_subpage = omap_write_subpage_bch; + pr_info("Using OMAP_ECC_BCH16_CODE_HW ECC scheme\n"); + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.size = 512; + chip->ecc.bytes = 26; + chip->ecc.strength = 16; + chip->ecc.hwctl = omap_enable_hwecc_bch; + chip->ecc.correct = omap_elm_correct_data; + chip->ecc.read_page = omap_read_page_bch; + chip->ecc.write_page = omap_write_page_bch; + chip->ecc.write_subpage = omap_write_subpage_bch; mtd_set_ooblayout(mtd, &omap_ooblayout_ops); - oobbytes_per_step = nand_chip->ecc.bytes; + oobbytes_per_step = chip->ecc.bytes; err = elm_config(info->elm_dev, BCH16_ECC, - mtd->writesize / nand_chip->ecc.size, - nand_chip->ecc.size, nand_chip->ecc.bytes); + mtd->writesize / chip->ecc.size, + chip->ecc.size, chip->ecc.bytes); if (err < 0) - goto return_error; + return err; break; default: - dev_err(&info->pdev->dev, "invalid or unsupported ECC scheme\n"); - err = -EINVAL; - goto return_error; + dev_err(dev, "Invalid or unsupported ECC scheme\n"); + return -EINVAL; } - /* check if NAND device's OOB is enough to store ECC signatures */ + /* Check if NAND device's OOB is enough to store ECC signatures */ min_oobbytes += (oobbytes_per_step * - (mtd->writesize / nand_chip->ecc.size)); + (mtd->writesize / chip->ecc.size)); if (mtd->oobsize < min_oobbytes) { - dev_err(&info->pdev->dev, - "not enough OOB bytes required = %d, available=%d\n", + dev_err(dev, + "Not enough OOB bytes: required = %d, available=%d\n", min_oobbytes, mtd->oobsize); - err = -EINVAL; - goto return_error; + return -EINVAL; + } + + return 0; +} + +static const struct nand_controller_ops omap_nand_controller_ops = { + .attach_chip = omap_nand_attach_chip, +}; + +/* Shared among all NAND instances to synchronize access to the ECC Engine */ +static struct nand_controller omap_gpmc_controller = { + .lock = __SPIN_LOCK_UNLOCKED(omap_gpmc_controller.lock), + .wq = __WAIT_QUEUE_HEAD_INITIALIZER(omap_gpmc_controller.wq), + .ops = &omap_nand_controller_ops, +}; + +static int omap_nand_probe(struct platform_device *pdev) +{ + struct omap_nand_info *info; + struct mtd_info *mtd; + struct nand_chip *nand_chip; + int err; + struct resource *res; + struct device *dev = &pdev->dev; + + info = devm_kzalloc(&pdev->dev, sizeof(struct omap_nand_info), + GFP_KERNEL); + if (!info) + return -ENOMEM; + + info->pdev = pdev; + + err = omap_get_dt_info(dev, info); + if (err) + return err; + + info->ops = gpmc_omap_get_nand_ops(&info->reg, info->gpmc_cs); + if (!info->ops) { + dev_err(&pdev->dev, "Failed to get GPMC->NAND interface\n"); + return -ENODEV; } -scan_tail: - /* second phase scan */ - err = nand_scan_tail(mtd); + nand_chip = &info->nand; + mtd = nand_to_mtd(nand_chip); + mtd->dev.parent = &pdev->dev; + nand_chip->ecc.priv = NULL; + nand_set_flash_node(nand_chip, dev->of_node); + + if (!mtd->name) { + mtd->name = devm_kasprintf(&pdev->dev, GFP_KERNEL, + "omap2-nand.%d", info->gpmc_cs); + if (!mtd->name) { + dev_err(&pdev->dev, "Failed to set MTD name\n"); + return -ENOMEM; + } + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + nand_chip->IO_ADDR_R = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(nand_chip->IO_ADDR_R)) + return PTR_ERR(nand_chip->IO_ADDR_R); + + info->phys_base = res->start; + + nand_chip->controller = &omap_gpmc_controller; + + nand_chip->IO_ADDR_W = nand_chip->IO_ADDR_R; + nand_chip->cmd_ctrl = omap_hwcontrol; + + info->ready_gpiod = devm_gpiod_get_optional(&pdev->dev, "rb", + GPIOD_IN); + if (IS_ERR(info->ready_gpiod)) { + dev_err(dev, "failed to get ready gpio\n"); + return PTR_ERR(info->ready_gpiod); + } + + /* + * If RDY/BSY line is connected to OMAP then use the omap ready + * function and the generic nand_wait function which reads the status + * register after monitoring the RDY/BSY line. Otherwise use a standard + * chip delay which is slightly more than tR (AC Timing) of the NAND + * device and read status register until you get a failure or success + */ + if (info->ready_gpiod) { + nand_chip->dev_ready = omap_dev_ready; + nand_chip->chip_delay = 0; + } else { + nand_chip->waitfunc = omap_wait; + nand_chip->chip_delay = 50; + } + + if (info->flash_bbt) + nand_chip->bbt_options |= NAND_BBT_USE_FLASH; + + /* scan NAND device connected to chip controller */ + nand_chip->options |= info->devsize & NAND_BUSWIDTH_16; + + err = nand_scan(mtd, 1); if (err) goto return_error; diff --git a/drivers/mtd/nand/raw/orion_nand.c b/drivers/mtd/nand/raw/orion_nand.c index 7825fd3ce66b..52d435285a3f 100644 --- a/drivers/mtd/nand/raw/orion_nand.c +++ b/drivers/mtd/nand/raw/orion_nand.c @@ -18,7 +18,7 @@ #include <linux/clk.h> #include <linux/err.h> #include <linux/io.h> -#include <asm/sizes.h> +#include <linux/sizes.h> #include <linux/platform_data/mtd-orion_nand.h> struct orion_nand_info { @@ -52,7 +52,7 @@ static void orion_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) { struct nand_chip *chip = mtd_to_nand(mtd); void __iomem *io_base = chip->IO_ADDR_R; -#if __LINUX_ARM_ARCH__ >= 5 +#if defined(__LINUX_ARM_ARCH__) && __LINUX_ARM_ARCH__ >= 5 uint64_t *buf64; #endif int i = 0; @@ -61,7 +61,7 @@ static void orion_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) *buf++ = readb(io_base); len--; } -#if __LINUX_ARM_ARCH__ >= 5 +#if defined(__LINUX_ARM_ARCH__) && __LINUX_ARM_ARCH__ >= 5 buf64 = (uint64_t *)buf; while (i < len/8) { /* @@ -153,9 +153,6 @@ static int __init orion_nand_probe(struct platform_device *pdev) if (board->width == 16) nc->options |= NAND_BUSWIDTH_16; - if (board->dev_ready) - nc->dev_ready = board->dev_ready; - platform_set_drvdata(pdev, info); /* Not all platforms can gate the clock, so it is not diff --git a/drivers/mtd/nand/raw/oxnas_nand.c b/drivers/mtd/nand/raw/oxnas_nand.c index d649d5944826..01b00bb69c1e 100644 --- a/drivers/mtd/nand/raw/oxnas_nand.c +++ b/drivers/mtd/nand/raw/oxnas_nand.c @@ -32,7 +32,7 @@ #define OXNAS_NAND_MAX_CHIPS 1 struct oxnas_nand_ctrl { - struct nand_hw_control base; + struct nand_controller base; void __iomem *io_base; struct clk *clk; struct nand_chip *chips[OXNAS_NAND_MAX_CHIPS]; @@ -96,7 +96,7 @@ static int oxnas_nand_probe(struct platform_device *pdev) if (!oxnas) return -ENOMEM; - nand_hw_control_init(&oxnas->base); + nand_controller_init(&oxnas->base); res = platform_get_resource(pdev, IORESOURCE_MEM, 0); oxnas->io_base = devm_ioremap_resource(&pdev->dev, res); diff --git a/drivers/mtd/nand/raw/plat_nand.c b/drivers/mtd/nand/raw/plat_nand.c index 925a1323604d..222626df4b96 100644 --- a/drivers/mtd/nand/raw/plat_nand.c +++ b/drivers/mtd/nand/raw/plat_nand.c @@ -67,12 +67,10 @@ static int plat_nand_probe(struct platform_device *pdev) data->chip.select_chip = pdata->ctrl.select_chip; data->chip.write_buf = pdata->ctrl.write_buf; data->chip.read_buf = pdata->ctrl.read_buf; - data->chip.read_byte = pdata->ctrl.read_byte; data->chip.chip_delay = pdata->chip.chip_delay; data->chip.options |= pdata->chip.options; data->chip.bbt_options |= pdata->chip.bbt_options; - data->chip.ecc.hwctl = pdata->ctrl.hwcontrol; data->chip.ecc.mode = NAND_ECC_SOFT; data->chip.ecc.algo = NAND_ECC_HAMMING; diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c index 6a5519f0ff25..d1d470bb32e4 100644 --- a/drivers/mtd/nand/raw/qcom_nandc.c +++ b/drivers/mtd/nand/raw/qcom_nandc.c @@ -213,6 +213,8 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ #define QPIC_PER_CW_CMD_SGL 32 #define QPIC_PER_CW_DATA_SGL 8 +#define QPIC_NAND_COMPLETION_TIMEOUT msecs_to_jiffies(2000) + /* * Flags used in DMA descriptor preparation helper functions * (i.e. read_reg_dma/write_reg_dma/read_data_dma/write_data_dma) @@ -245,6 +247,11 @@ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ * @tx_sgl_start - start index in data sgl for tx. * @rx_sgl_pos - current index in data sgl for rx. * @rx_sgl_start - start index in data sgl for rx. + * @wait_second_completion - wait for second DMA desc completion before making + * the NAND transfer completion. + * @txn_done - completion for NAND transfer. + * @last_data_desc - last DMA desc in data channel (tx/rx). + * @last_cmd_desc - last DMA desc in command channel. */ struct bam_transaction { struct bam_cmd_element *bam_ce; @@ -258,6 +265,10 @@ struct bam_transaction { u32 tx_sgl_start; u32 rx_sgl_pos; u32 rx_sgl_start; + bool wait_second_completion; + struct completion txn_done; + struct dma_async_tx_descriptor *last_data_desc; + struct dma_async_tx_descriptor *last_cmd_desc; }; /* @@ -354,7 +365,7 @@ struct nandc_regs { * from all connected NAND devices pagesize */ struct qcom_nand_controller { - struct nand_hw_control controller; + struct nand_controller controller; struct list_head host_list; struct device *dev; @@ -504,6 +515,8 @@ alloc_bam_transaction(struct qcom_nand_controller *nandc) bam_txn->data_sgl = bam_txn_buf; + init_completion(&bam_txn->txn_done); + return bam_txn; } @@ -523,11 +536,33 @@ static void clear_bam_transaction(struct qcom_nand_controller *nandc) bam_txn->tx_sgl_start = 0; bam_txn->rx_sgl_pos = 0; bam_txn->rx_sgl_start = 0; + bam_txn->last_data_desc = NULL; + bam_txn->wait_second_completion = false; sg_init_table(bam_txn->cmd_sgl, nandc->max_cwperpage * QPIC_PER_CW_CMD_SGL); sg_init_table(bam_txn->data_sgl, nandc->max_cwperpage * QPIC_PER_CW_DATA_SGL); + + reinit_completion(&bam_txn->txn_done); +} + +/* Callback for DMA descriptor completion */ +static void qpic_bam_dma_done(void *data) +{ + struct bam_transaction *bam_txn = data; + + /* + * In case of data transfer with NAND, 2 callbacks will be generated. + * One for command channel and another one for data channel. + * If current transaction has data descriptors + * (i.e. wait_second_completion is true), then set this to false + * and wait for second DMA descriptor completion. + */ + if (bam_txn->wait_second_completion) + bam_txn->wait_second_completion = false; + else + complete(&bam_txn->txn_done); } static inline struct qcom_nand_host *to_qcom_nand_host(struct nand_chip *chip) @@ -756,6 +791,12 @@ static int prepare_bam_async_desc(struct qcom_nand_controller *nandc, desc->dma_desc = dma_desc; + /* update last data/command descriptor */ + if (chan == nandc->cmd_chan) + bam_txn->last_cmd_desc = dma_desc; + else + bam_txn->last_data_desc = dma_desc; + list_add_tail(&desc->node, &nandc->desc_list); return 0; @@ -1055,7 +1096,8 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc) * Helper to prepare DMA descriptors for configuring registers * before reading each codeword in NAND page. */ -static void config_nand_cw_read(struct qcom_nand_controller *nandc) +static void +config_nand_cw_read(struct qcom_nand_controller *nandc, bool use_ecc) { if (nandc->props->is_bam) write_reg_dma(nandc, NAND_READ_LOCATION_0, 4, @@ -1064,19 +1106,25 @@ static void config_nand_cw_read(struct qcom_nand_controller *nandc) write_reg_dma(nandc, NAND_FLASH_CMD, 1, NAND_BAM_NEXT_SGL); write_reg_dma(nandc, NAND_EXEC_CMD, 1, NAND_BAM_NEXT_SGL); - read_reg_dma(nandc, NAND_FLASH_STATUS, 2, 0); - read_reg_dma(nandc, NAND_ERASED_CW_DETECT_STATUS, 1, - NAND_BAM_NEXT_SGL); + if (use_ecc) { + read_reg_dma(nandc, NAND_FLASH_STATUS, 2, 0); + read_reg_dma(nandc, NAND_ERASED_CW_DETECT_STATUS, 1, + NAND_BAM_NEXT_SGL); + } else { + read_reg_dma(nandc, NAND_FLASH_STATUS, 1, NAND_BAM_NEXT_SGL); + } } /* * Helper to prepare dma descriptors to configure registers needed for reading a * single codeword in page */ -static void config_nand_single_cw_page_read(struct qcom_nand_controller *nandc) +static void +config_nand_single_cw_page_read(struct qcom_nand_controller *nandc, + bool use_ecc) { config_nand_page_read(nandc); - config_nand_cw_read(nandc); + config_nand_cw_read(nandc, use_ecc); } /* @@ -1157,7 +1205,7 @@ static int nandc_param(struct qcom_nand_host *host) nandc->buf_count = 512; memset(nandc->data_buffer, 0xff, nandc->buf_count); - config_nand_single_cw_page_read(nandc); + config_nand_single_cw_page_read(nandc, false); read_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, nandc->buf_count, 0); @@ -1273,10 +1321,20 @@ static int submit_descs(struct qcom_nand_controller *nandc) cookie = dmaengine_submit(desc->dma_desc); if (nandc->props->is_bam) { + bam_txn->last_cmd_desc->callback = qpic_bam_dma_done; + bam_txn->last_cmd_desc->callback_param = bam_txn; + if (bam_txn->last_data_desc) { + bam_txn->last_data_desc->callback = qpic_bam_dma_done; + bam_txn->last_data_desc->callback_param = bam_txn; + bam_txn->wait_second_completion = true; + } + dma_async_issue_pending(nandc->tx_chan); dma_async_issue_pending(nandc->rx_chan); + dma_async_issue_pending(nandc->cmd_chan); - if (dma_sync_wait(nandc->cmd_chan, cookie) != DMA_COMPLETE) + if (!wait_for_completion_timeout(&bam_txn->txn_done, + QPIC_NAND_COMPLETION_TIMEOUT)) return -ETIMEDOUT; } else { if (dma_sync_wait(nandc->chan, cookie) != DMA_COMPLETE) @@ -1512,20 +1570,180 @@ struct read_stats { __le32 erased_cw; }; +/* reads back FLASH_STATUS register set by the controller */ +static int check_flash_errors(struct qcom_nand_host *host, int cw_cnt) +{ + struct nand_chip *chip = &host->chip; + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + int i; + + for (i = 0; i < cw_cnt; i++) { + u32 flash = le32_to_cpu(nandc->reg_read_buf[i]); + + if (flash & (FS_OP_ERR | FS_MPU_ERR)) + return -EIO; + } + + return 0; +} + +/* performs raw read for one codeword */ +static int +qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, + u8 *data_buf, u8 *oob_buf, int page, int cw) +{ + struct qcom_nand_host *host = to_qcom_nand_host(chip); + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + int data_size1, data_size2, oob_size1, oob_size2; + int ret, reg_off = FLASH_BUF_ACC, read_loc = 0; + + nand_read_page_op(chip, page, 0, NULL, 0); + host->use_ecc = false; + + clear_bam_transaction(nandc); + set_address(host, host->cw_size * cw, page); + update_rw_regs(host, 1, true); + config_nand_page_read(nandc); + + data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); + oob_size1 = host->bbm_size; + + if (cw == (ecc->steps - 1)) { + data_size2 = ecc->size - data_size1 - + ((ecc->steps - 1) * 4); + oob_size2 = (ecc->steps * 4) + host->ecc_bytes_hw + + host->spare_bytes; + } else { + data_size2 = host->cw_data - data_size1; + oob_size2 = host->ecc_bytes_hw + host->spare_bytes; + } + + if (nandc->props->is_bam) { + nandc_set_read_loc(nandc, 0, read_loc, data_size1, 0); + read_loc += data_size1; + + nandc_set_read_loc(nandc, 1, read_loc, oob_size1, 0); + read_loc += oob_size1; + + nandc_set_read_loc(nandc, 2, read_loc, data_size2, 0); + read_loc += data_size2; + + nandc_set_read_loc(nandc, 3, read_loc, oob_size2, 1); + } + + config_nand_cw_read(nandc, false); + + read_data_dma(nandc, reg_off, data_buf, data_size1, 0); + reg_off += data_size1; + + read_data_dma(nandc, reg_off, oob_buf, oob_size1, 0); + reg_off += oob_size1; + + read_data_dma(nandc, reg_off, data_buf + data_size1, data_size2, 0); + reg_off += data_size2; + + read_data_dma(nandc, reg_off, oob_buf + oob_size1, oob_size2, 0); + + ret = submit_descs(nandc); + free_descs(nandc); + if (ret) { + dev_err(nandc->dev, "failure to read raw cw %d\n", cw); + return ret; + } + + return check_flash_errors(host, 1); +} + +/* + * Bitflips can happen in erased codewords also so this function counts the + * number of 0 in each CW for which ECC engine returns the uncorrectable + * error. The page will be assumed as erased if this count is less than or + * equal to the ecc->strength for each CW. + * + * 1. Both DATA and OOB need to be checked for number of 0. The + * top-level API can be called with only data buf or OOB buf so use + * chip->data_buf if data buf is null and chip->oob_poi if oob buf + * is null for copying the raw bytes. + * 2. Perform raw read for all the CW which has uncorrectable errors. + * 3. For each CW, check the number of 0 in cw_data and usable OOB bytes. + * The BBM and spare bytes bit flip won’t affect the ECC so don’t check + * the number of bitflips in this area. + */ +static int +check_for_erased_page(struct qcom_nand_host *host, u8 *data_buf, + u8 *oob_buf, unsigned long uncorrectable_cws, + int page, unsigned int max_bitflips) +{ + struct nand_chip *chip = &host->chip; + struct mtd_info *mtd = nand_to_mtd(chip); + struct nand_ecc_ctrl *ecc = &chip->ecc; + u8 *cw_data_buf, *cw_oob_buf; + int cw, data_size, oob_size, ret = 0; + + if (!data_buf) { + data_buf = chip->data_buf; + chip->pagebuf = -1; + } + + if (!oob_buf) { + oob_buf = chip->oob_poi; + chip->pagebuf = -1; + } + + for_each_set_bit(cw, &uncorrectable_cws, ecc->steps) { + if (cw == (ecc->steps - 1)) { + data_size = ecc->size - ((ecc->steps - 1) * 4); + oob_size = (ecc->steps * 4) + host->ecc_bytes_hw; + } else { + data_size = host->cw_data; + oob_size = host->ecc_bytes_hw; + } + + /* determine starting buffer address for current CW */ + cw_data_buf = data_buf + (cw * host->cw_data); + cw_oob_buf = oob_buf + (cw * ecc->bytes); + + ret = qcom_nandc_read_cw_raw(mtd, chip, cw_data_buf, + cw_oob_buf, page, cw); + if (ret) + return ret; + + /* + * make sure it isn't an erased page reported + * as not-erased by HW because of a few bitflips + */ + ret = nand_check_erased_ecc_chunk(cw_data_buf, data_size, + cw_oob_buf + host->bbm_size, + oob_size, NULL, + 0, ecc->strength); + if (ret < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += ret; + max_bitflips = max_t(unsigned int, max_bitflips, ret); + } + } + + return max_bitflips; +} + /* * reads back status registers set by the controller to notify page read * errors. this is equivalent to what 'ecc->correct()' would do. */ static int parse_read_errors(struct qcom_nand_host *host, u8 *data_buf, - u8 *oob_buf) + u8 *oob_buf, int page) { struct nand_chip *chip = &host->chip; struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); struct mtd_info *mtd = nand_to_mtd(chip); struct nand_ecc_ctrl *ecc = &chip->ecc; - unsigned int max_bitflips = 0; + unsigned int max_bitflips = 0, uncorrectable_cws = 0; struct read_stats *buf; + bool flash_op_err = false, erased; int i; + u8 *data_buf_start = data_buf, *oob_buf_start = oob_buf; buf = (struct read_stats *)nandc->reg_read_buf; nandc_read_buffer_sync(nandc, true); @@ -1546,48 +1764,49 @@ static int parse_read_errors(struct qcom_nand_host *host, u8 *data_buf, buffer = le32_to_cpu(buf->buffer); erased_cw = le32_to_cpu(buf->erased_cw); - if (flash & (FS_OP_ERR | FS_MPU_ERR)) { - bool erased; - - /* ignore erased codeword errors */ + /* + * Check ECC failure for each codeword. ECC failure can + * happen in either of the following conditions + * 1. If number of bitflips are greater than ECC engine + * capability. + * 2. If this codeword contains all 0xff for which erased + * codeword detection check will be done. + */ + if ((flash & FS_OP_ERR) && (buffer & BS_UNCORRECTABLE_BIT)) { + /* + * For BCH ECC, ignore erased codeword errors, if + * ERASED_CW bits are set. + */ if (host->bch_enabled) { erased = (erased_cw & ERASED_CW) == ERASED_CW ? true : false; - } else { + /* + * For RS ECC, HW reports the erased CW by placing + * special characters at certain offsets in the buffer. + * These special characters will be valid only if + * complete page is read i.e. data_buf is not NULL. + */ + } else if (data_buf) { erased = erased_chunk_check_and_fixup(data_buf, data_len); + } else { + erased = false; } - if (erased) { - data_buf += data_len; - if (oob_buf) - oob_buf += oob_len + ecc->bytes; - continue; - } - - if (buffer & BS_UNCORRECTABLE_BIT) { - int ret, ecclen, extraooblen; - void *eccbuf; - - eccbuf = oob_buf ? oob_buf + oob_len : NULL; - ecclen = oob_buf ? host->ecc_bytes_hw : 0; - extraooblen = oob_buf ? oob_len : 0; - - /* - * make sure it isn't an erased page reported - * as not-erased by HW because of a few bitflips - */ - ret = nand_check_erased_ecc_chunk(data_buf, - data_len, eccbuf, ecclen, oob_buf, - extraooblen, ecc->strength); - if (ret < 0) { - mtd->ecc_stats.failed++; - } else { - mtd->ecc_stats.corrected += ret; - max_bitflips = - max_t(unsigned int, max_bitflips, ret); - } - } + if (!erased) + uncorrectable_cws |= BIT(i); + /* + * Check if MPU or any other operational error (timeout, + * device failure, etc.) happened for this codeword and + * make flash_op_err true. If flash_op_err is set, then + * EIO will be returned for page read. + */ + } else if (flash & (FS_OP_ERR | FS_MPU_ERR)) { + flash_op_err = true; + /* + * No ECC or operational errors happened. Check the number of + * bits corrected and update the ecc_stats.corrected. + */ } else { unsigned int stat; @@ -1596,12 +1815,21 @@ static int parse_read_errors(struct qcom_nand_host *host, u8 *data_buf, max_bitflips = max(max_bitflips, stat); } - data_buf += data_len; + if (data_buf) + data_buf += data_len; if (oob_buf) oob_buf += oob_len + ecc->bytes; } - return max_bitflips; + if (flash_op_err) + return -EIO; + + if (!uncorrectable_cws) + return max_bitflips; + + return check_for_erased_page(host, data_buf_start, oob_buf_start, + uncorrectable_cws, page, + max_bitflips); } /* @@ -1609,11 +1837,12 @@ static int parse_read_errors(struct qcom_nand_host *host, u8 *data_buf, * ecc->read_oob() */ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf, - u8 *oob_buf) + u8 *oob_buf, int page) { struct nand_chip *chip = &host->chip; struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); struct nand_ecc_ctrl *ecc = &chip->ecc; + u8 *data_buf_start = data_buf, *oob_buf_start = oob_buf; int i, ret; config_nand_page_read(nandc); @@ -1644,7 +1873,7 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf, } } - config_nand_cw_read(nandc); + config_nand_cw_read(nandc, true); if (data_buf) read_data_dma(nandc, FLASH_BUF_ACC, data_buf, @@ -1674,12 +1903,14 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf, } ret = submit_descs(nandc); - if (ret) - dev_err(nandc->dev, "failure to read page/oob\n"); - free_descs(nandc); - return ret; + if (ret) { + dev_err(nandc->dev, "failure to read page/oob\n"); + return ret; + } + + return parse_read_errors(host, data_buf_start, oob_buf_start, page); } /* @@ -1704,7 +1935,7 @@ static int copy_last_cw(struct qcom_nand_host *host, int page) set_address(host, host->cw_size * (ecc->steps - 1), page); update_rw_regs(host, 1, true); - config_nand_single_cw_page_read(nandc); + config_nand_single_cw_page_read(nandc, host->use_ecc); read_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, size, 0); @@ -1724,20 +1955,14 @@ static int qcom_nandc_read_page(struct mtd_info *mtd, struct nand_chip *chip, struct qcom_nand_host *host = to_qcom_nand_host(chip); struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); u8 *data_buf, *oob_buf = NULL; - int ret; nand_read_page_op(chip, page, 0, NULL, 0); data_buf = buf; oob_buf = oob_required ? chip->oob_poi : NULL; clear_bam_transaction(nandc); - ret = read_page_ecc(host, data_buf, oob_buf); - if (ret) { - dev_err(nandc->dev, "failure to read page\n"); - return ret; - } - return parse_read_errors(host, data_buf, oob_buf); + return read_page_ecc(host, data_buf, oob_buf, page); } /* implements ecc->read_page_raw() */ @@ -1746,77 +1971,20 @@ static int qcom_nandc_read_page_raw(struct mtd_info *mtd, int oob_required, int page) { struct qcom_nand_host *host = to_qcom_nand_host(chip); - struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); - u8 *data_buf, *oob_buf; struct nand_ecc_ctrl *ecc = &chip->ecc; - int i, ret; - int read_loc; - - nand_read_page_op(chip, page, 0, NULL, 0); - data_buf = buf; - oob_buf = chip->oob_poi; - - host->use_ecc = false; + int cw, ret; + u8 *data_buf = buf, *oob_buf = chip->oob_poi; - clear_bam_transaction(nandc); - update_rw_regs(host, ecc->steps, true); - config_nand_page_read(nandc); - - for (i = 0; i < ecc->steps; i++) { - int data_size1, data_size2, oob_size1, oob_size2; - int reg_off = FLASH_BUF_ACC; - - data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); - oob_size1 = host->bbm_size; - - if (i == (ecc->steps - 1)) { - data_size2 = ecc->size - data_size1 - - ((ecc->steps - 1) << 2); - oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw + - host->spare_bytes; - } else { - data_size2 = host->cw_data - data_size1; - oob_size2 = host->ecc_bytes_hw + host->spare_bytes; - } - - if (nandc->props->is_bam) { - read_loc = 0; - nandc_set_read_loc(nandc, 0, read_loc, data_size1, 0); - read_loc += data_size1; - - nandc_set_read_loc(nandc, 1, read_loc, oob_size1, 0); - read_loc += oob_size1; - - nandc_set_read_loc(nandc, 2, read_loc, data_size2, 0); - read_loc += data_size2; - - nandc_set_read_loc(nandc, 3, read_loc, oob_size2, 1); - } - - config_nand_cw_read(nandc); - - read_data_dma(nandc, reg_off, data_buf, data_size1, 0); - reg_off += data_size1; - data_buf += data_size1; - - read_data_dma(nandc, reg_off, oob_buf, oob_size1, 0); - reg_off += oob_size1; - oob_buf += oob_size1; - - read_data_dma(nandc, reg_off, data_buf, data_size2, 0); - reg_off += data_size2; - data_buf += data_size2; + for (cw = 0; cw < ecc->steps; cw++) { + ret = qcom_nandc_read_cw_raw(mtd, chip, data_buf, oob_buf, + page, cw); + if (ret) + return ret; - read_data_dma(nandc, reg_off, oob_buf, oob_size2, 0); - oob_buf += oob_size2; + data_buf += host->cw_data; + oob_buf += ecc->bytes; } - ret = submit_descs(nandc); - if (ret) - dev_err(nandc->dev, "failure to read raw page\n"); - - free_descs(nandc); - return 0; } @@ -1827,7 +1995,6 @@ static int qcom_nandc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, struct qcom_nand_host *host = to_qcom_nand_host(chip); struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); struct nand_ecc_ctrl *ecc = &chip->ecc; - int ret; clear_read_regs(nandc); clear_bam_transaction(nandc); @@ -1836,11 +2003,7 @@ static int qcom_nandc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, set_address(host, 0, page); update_rw_regs(host, ecc->steps, true); - ret = read_page_ecc(host, NULL, chip->oob_poi); - if (ret) - dev_err(nandc->dev, "failure to read oob\n"); - - return ret; + return read_page_ecc(host, NULL, chip->oob_poi, page); } /* implements ecc->write_page() */ @@ -1988,11 +2151,9 @@ static int qcom_nandc_write_page_raw(struct mtd_info *mtd, /* * implements ecc->write_oob() * - * the NAND controller cannot write only data or only oob within a codeword, - * since ecc is calculated for the combined codeword. we first copy the - * entire contents for the last codeword(data + oob), replace the old oob - * with the new one in chip->oob_poi, and then write the entire codeword. - * this read-copy-write operation results in a slight performance loss. + * the NAND controller cannot write only data or only OOB within a codeword + * since ECC is calculated for the combined codeword. So update the OOB from + * chip->oob_poi, and pad the data area with OxFF before writing. */ static int qcom_nandc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) @@ -2005,19 +2166,13 @@ static int qcom_nandc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int ret; host->use_ecc = true; - - clear_bam_transaction(nandc); - ret = copy_last_cw(host, page); - if (ret) - return ret; - - clear_read_regs(nandc); clear_bam_transaction(nandc); /* calculate the data and oob size for the last codeword/step */ data_size = ecc->size - ((ecc->steps - 1) << 2); oob_size = mtd->oobavail; + memset(nandc->data_buffer, 0xff, host->cw_data); /* override new oob content to last codeword */ mtd_ooblayout_get_databytes(mtd, nandc->data_buffer + data_size, oob, 0, mtd->oobavail); @@ -2049,7 +2204,6 @@ static int qcom_nandc_block_bad(struct mtd_info *mtd, loff_t ofs) struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); struct nand_ecc_ctrl *ecc = &chip->ecc; int page, ret, bbpos, bad = 0; - u32 flash_status; page = (int)(ofs >> chip->page_shift) & chip->pagemask; @@ -2066,9 +2220,7 @@ static int qcom_nandc_block_bad(struct mtd_info *mtd, loff_t ofs) if (ret) goto err; - flash_status = le32_to_cpu(nandc->reg_read_buf[0]); - - if (flash_status & (FS_OP_ERR | FS_MPU_ERR)) { + if (check_flash_errors(host, 1)) { dev_warn(nandc->dev, "error when trying to read BBM\n"); goto err; } @@ -2315,27 +2467,40 @@ static const struct mtd_ooblayout_ops qcom_nand_ooblayout_ops = { .free = qcom_nand_ooblayout_free, }; -static int qcom_nand_host_setup(struct qcom_nand_host *host) +static int +qcom_nandc_calc_ecc_bytes(int step_size, int strength) +{ + return strength == 4 ? 12 : 16; +} +NAND_ECC_CAPS_SINGLE(qcom_nandc_ecc_caps, qcom_nandc_calc_ecc_bytes, + NANDC_STEP_SIZE, 4, 8); + +static int qcom_nand_attach_chip(struct nand_chip *chip) { - struct nand_chip *chip = &host->chip; struct mtd_info *mtd = nand_to_mtd(chip); + struct qcom_nand_host *host = to_qcom_nand_host(chip); struct nand_ecc_ctrl *ecc = &chip->ecc; struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); - int cwperpage, bad_block_byte; + int cwperpage, bad_block_byte, ret; bool wide_bus; int ecc_mode = 1; + /* controller only supports 512 bytes data steps */ + ecc->size = NANDC_STEP_SIZE; + wide_bus = chip->options & NAND_BUSWIDTH_16 ? true : false; + cwperpage = mtd->writesize / NANDC_STEP_SIZE; + /* - * the controller requires each step consists of 512 bytes of data. - * bail out if DT has populated a wrong step size. + * Each CW has 4 available OOB bytes which will be protected with ECC + * so remaining bytes can be used for ECC. */ - if (ecc->size != NANDC_STEP_SIZE) { - dev_err(nandc->dev, "invalid ecc size\n"); - return -EINVAL; + ret = nand_ecc_choose_conf(chip, &qcom_nandc_ecc_caps, + mtd->oobsize - (cwperpage * 4)); + if (ret) { + dev_err(nandc->dev, "No valid ECC settings possible\n"); + return ret; } - wide_bus = chip->options & NAND_BUSWIDTH_16 ? true : false; - if (ecc->strength >= 8) { /* 8 bit ECC defaults to BCH ECC on all platforms */ host->bch_enabled = true; @@ -2403,7 +2568,6 @@ static int qcom_nand_host_setup(struct qcom_nand_host *host) mtd_set_ooblayout(mtd, &qcom_nand_ooblayout_ops); - cwperpage = mtd->writesize / ecc->size; nandc->max_cwperpage = max_t(unsigned int, nandc->max_cwperpage, cwperpage); @@ -2419,12 +2583,6 @@ static int qcom_nand_host_setup(struct qcom_nand_host *host) * for 8 bit ECC */ host->cw_size = host->cw_data + ecc->bytes; - - if (ecc->bytes * (mtd->writesize / ecc->size) > mtd->oobsize) { - dev_err(nandc->dev, "ecc data doesn't fit in OOB area\n"); - return -EINVAL; - } - bad_block_byte = mtd->writesize - host->cw_size * (cwperpage - 1) + 1; host->cfg0 = (cwperpage - 1) << CW_PER_PAGE @@ -2482,6 +2640,10 @@ static int qcom_nand_host_setup(struct qcom_nand_host *host) return 0; } +static const struct nand_controller_ops qcom_nandc_ops = { + .attach_chip = qcom_nand_attach_chip, +}; + static int qcom_nandc_alloc(struct qcom_nand_controller *nandc) { int ret; @@ -2570,7 +2732,8 @@ static int qcom_nandc_alloc(struct qcom_nand_controller *nandc) INIT_LIST_HEAD(&nandc->desc_list); INIT_LIST_HEAD(&nandc->host_list); - nand_hw_control_init(&nandc->controller); + nand_controller_init(&nandc->controller); + nandc->controller.ops = &qcom_nandc_ops; return 0; } @@ -2623,9 +2786,9 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc) return 0; } -static int qcom_nand_host_init(struct qcom_nand_controller *nandc, - struct qcom_nand_host *host, - struct device_node *dn) +static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, + struct qcom_nand_host *host, + struct device_node *dn) { struct nand_chip *chip = &host->chip; struct mtd_info *mtd = nand_to_mtd(chip); @@ -2672,30 +2835,13 @@ static int qcom_nand_host_init(struct qcom_nand_controller *nandc, /* set up initial status value */ host->status = NAND_STATUS_READY | NAND_STATUS_WP; - ret = nand_scan_ident(mtd, 1, NULL); - if (ret) - return ret; - - ret = qcom_nand_host_setup(host); - - return ret; -} - -static int qcom_nand_mtd_register(struct qcom_nand_controller *nandc, - struct qcom_nand_host *host, - struct device_node *dn) -{ - struct nand_chip *chip = &host->chip; - struct mtd_info *mtd = nand_to_mtd(chip); - int ret; - - ret = nand_scan_tail(mtd); + ret = nand_scan(mtd, 1); if (ret) return ret; ret = mtd_device_register(mtd, NULL, 0); if (ret) - nand_cleanup(mtd_to_nand(mtd)); + nand_cleanup(chip); return ret; } @@ -2704,28 +2850,9 @@ static int qcom_probe_nand_devices(struct qcom_nand_controller *nandc) { struct device *dev = nandc->dev; struct device_node *dn = dev->of_node, *child; - struct qcom_nand_host *host, *tmp; + struct qcom_nand_host *host; int ret; - for_each_available_child_of_node(dn, child) { - host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL); - if (!host) { - of_node_put(child); - return -ENOMEM; - } - - ret = qcom_nand_host_init(nandc, host, child); - if (ret) { - devm_kfree(dev, host); - continue; - } - - list_add_tail(&host->node, &nandc->host_list); - } - - if (list_empty(&nandc->host_list)) - return -ENODEV; - if (nandc->props->is_bam) { free_bam_transaction(nandc); nandc->bam_txn = alloc_bam_transaction(nandc); @@ -2736,12 +2863,20 @@ static int qcom_probe_nand_devices(struct qcom_nand_controller *nandc) } } - list_for_each_entry_safe(host, tmp, &nandc->host_list, node) { - ret = qcom_nand_mtd_register(nandc, host, child); + for_each_available_child_of_node(dn, child) { + host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL); + if (!host) { + of_node_put(child); + return -ENOMEM; + } + + ret = qcom_nand_host_init_and_register(nandc, host, child); if (ret) { - list_del(&host->node); devm_kfree(dev, host); + continue; } + + list_add_tail(&host->node, &nandc->host_list); } if (list_empty(&nandc->host_list)) @@ -2799,14 +2934,6 @@ static int qcom_nandc_probe(struct platform_device *pdev) nandc->props = dev_data; - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - nandc->base = devm_ioremap_resource(dev, res); - if (IS_ERR(nandc->base)) - return PTR_ERR(nandc->base); - - nandc->base_phys = res->start; - nandc->base_dma = phys_to_dma(dev, (phys_addr_t)res->start); - nandc->core_clk = devm_clk_get(dev, "core"); if (IS_ERR(nandc->core_clk)) return PTR_ERR(nandc->core_clk); @@ -2819,9 +2946,21 @@ static int qcom_nandc_probe(struct platform_device *pdev) if (ret) return ret; + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + nandc->base = devm_ioremap_resource(dev, res); + if (IS_ERR(nandc->base)) + return PTR_ERR(nandc->base); + + nandc->base_phys = res->start; + nandc->base_dma = dma_map_resource(dev, res->start, + resource_size(res), + DMA_BIDIRECTIONAL, 0); + if (!nandc->base_dma) + return -ENXIO; + ret = qcom_nandc_alloc(nandc); if (ret) - goto err_core_clk; + goto err_nandc_alloc; ret = clk_prepare_enable(nandc->core_clk); if (ret) @@ -2847,6 +2986,9 @@ err_aon_clk: clk_disable_unprepare(nandc->core_clk); err_core_clk: qcom_nandc_unalloc(nandc); +err_nandc_alloc: + dma_unmap_resource(dev, res->start, resource_size(res), + DMA_BIDIRECTIONAL, 0); return ret; } @@ -2854,16 +2996,21 @@ err_core_clk: static int qcom_nandc_remove(struct platform_device *pdev) { struct qcom_nand_controller *nandc = platform_get_drvdata(pdev); + struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); struct qcom_nand_host *host; list_for_each_entry(host, &nandc->host_list, node) nand_release(nand_to_mtd(&host->chip)); + qcom_nandc_unalloc(nandc); clk_disable_unprepare(nandc->aon_clk); clk_disable_unprepare(nandc->core_clk); + dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res), + DMA_BIDIRECTIONAL, 0); + return 0; } diff --git a/drivers/mtd/nand/raw/s3c2410.c b/drivers/mtd/nand/raw/s3c2410.c index 19661c5d3220..c21e8892394a 100644 --- a/drivers/mtd/nand/raw/s3c2410.c +++ b/drivers/mtd/nand/raw/s3c2410.c @@ -162,7 +162,7 @@ enum s3c_nand_clk_state { */ struct s3c2410_nand_info { /* mtd info */ - struct nand_hw_control controller; + struct nand_controller controller; struct s3c2410_nand_mtd *mtds; struct s3c2410_platform_nand *platform; @@ -802,8 +802,8 @@ static int s3c2410_nand_add_partition(struct s3c2410_nand_info *info, mtdinfo->name = set->name; - return mtd_device_parse_register(mtdinfo, NULL, NULL, - set->partitions, set->nr_partitions); + return mtd_device_register(mtdinfo, set->partitions, + set->nr_partitions); } return -ENODEV; @@ -915,20 +915,19 @@ static void s3c2410_nand_init_chip(struct s3c2410_nand_info *info, } /** - * s3c2410_nand_update_chip - post probe update - * @info: The controller instance. - * @nmtd: The driver version of the MTD instance. + * s3c2410_nand_attach_chip - Init the ECC engine after NAND scan + * @chip: The NAND chip * - * This routine is called after the chip probe has successfully completed - * and the relevant per-chip information updated. This call ensure that + * This hook is called by the core after the identification of the NAND chip, + * once the relevant per-chip information is up to date.. This call ensure that * we update the internal state accordingly. * * The internal state is currently limited to the ECC state information. */ -static int s3c2410_nand_update_chip(struct s3c2410_nand_info *info, - struct s3c2410_nand_mtd *nmtd) +static int s3c2410_nand_attach_chip(struct nand_chip *chip) { - struct nand_chip *chip = &nmtd->chip; + struct mtd_info *mtd = nand_to_mtd(chip); + struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd); switch (chip->ecc.mode) { @@ -998,6 +997,10 @@ static int s3c2410_nand_update_chip(struct s3c2410_nand_info *info, return 0; } +static const struct nand_controller_ops s3c24xx_nand_controller_ops = { + .attach_chip = s3c2410_nand_attach_chip, +}; + static const struct of_device_id s3c24xx_nand_dt_ids[] = { { .compatible = "samsung,s3c2410-nand", @@ -1094,7 +1097,8 @@ static int s3c24xx_nand_probe(struct platform_device *pdev) platform_set_drvdata(pdev, info); - nand_hw_control_init(&info->controller); + nand_controller_init(&info->controller); + info->controller.ops = &s3c24xx_nand_controller_ops; /* get the clock source and enable it */ @@ -1134,8 +1138,13 @@ static int s3c24xx_nand_probe(struct platform_device *pdev) dev_dbg(&pdev->dev, "mapped registers at %p\n", info->regs); - sets = (plat != NULL) ? plat->sets : NULL; - nr_sets = (plat != NULL) ? plat->nr_sets : 1; + if (!plat->sets || plat->nr_sets < 1) { + err = -EINVAL; + goto exit_error; + } + + sets = plat->sets; + nr_sets = plat->nr_sets; info->mtd_count = nr_sets; @@ -1152,7 +1161,7 @@ static int s3c24xx_nand_probe(struct platform_device *pdev) nmtd = info->mtds; - for (setno = 0; setno < nr_sets; setno++, nmtd++) { + for (setno = 0; setno < nr_sets; setno++, nmtd++, sets++) { struct mtd_info *mtd = nand_to_mtd(&nmtd->chip); pr_debug("initialising set %d (%p, info %p)\n", @@ -1161,22 +1170,11 @@ static int s3c24xx_nand_probe(struct platform_device *pdev) mtd->dev.parent = &pdev->dev; s3c2410_nand_init_chip(info, nmtd, sets); - err = nand_scan_ident(mtd, (sets) ? sets->nr_chips : 1, NULL); - if (err) - goto exit_error; - - err = s3c2410_nand_update_chip(info, nmtd); - if (err < 0) - goto exit_error; - - err = nand_scan_tail(mtd); + err = nand_scan(mtd, sets ? sets->nr_chips : 1); if (err) goto exit_error; s3c2410_nand_add_partition(info, nmtd, sets); - - if (sets != NULL) - sets++; } /* initialise the hardware */ diff --git a/drivers/mtd/nand/raw/sh_flctl.c b/drivers/mtd/nand/raw/sh_flctl.c index c7abceffcc40..bb8866e05ff7 100644 --- a/drivers/mtd/nand/raw/sh_flctl.c +++ b/drivers/mtd/nand/raw/sh_flctl.c @@ -1002,10 +1002,17 @@ static void flctl_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) flctl->index += len; } -static int flctl_chip_init_tail(struct mtd_info *mtd) +static int flctl_chip_attach_chip(struct nand_chip *chip) { + struct mtd_info *mtd = nand_to_mtd(chip); struct sh_flctl *flctl = mtd_to_flctl(mtd); - struct nand_chip *chip = &flctl->chip; + + /* + * NAND_BUSWIDTH_16 may have been set by nand_scan_ident(). + * Add the SEL_16BIT flag in flctl->flcmncr_base. + */ + if (chip->options & NAND_BUSWIDTH_16) + flctl->flcmncr_base |= SEL_16BIT; if (mtd->writesize == 512) { flctl->page_size = 0; @@ -1063,6 +1070,10 @@ static int flctl_chip_init_tail(struct mtd_info *mtd) return 0; } +static const struct nand_controller_ops flctl_nand_controller_ops = { + .attach_chip = flctl_chip_attach_chip, +}; + static irqreturn_t flctl_handle_flste(int irq, void *dev_id) { struct sh_flctl *flctl = dev_id; @@ -1191,25 +1202,8 @@ static int flctl_probe(struct platform_device *pdev) flctl_setup_dma(flctl); - ret = nand_scan_ident(flctl_mtd, 1, NULL); - if (ret) - goto err_chip; - - if (nand->options & NAND_BUSWIDTH_16) { - /* - * NAND_BUSWIDTH_16 may have been set by nand_scan_ident(). - * Add the SEL_16BIT flag in pdata->flcmncr_val and re-assign - * flctl->flcmncr_base to pdata->flcmncr_val. - */ - pdata->flcmncr_val |= SEL_16BIT; - flctl->flcmncr_base = pdata->flcmncr_val; - } - - ret = flctl_chip_init_tail(flctl_mtd); - if (ret) - goto err_chip; - - ret = nand_scan_tail(flctl_mtd); + nand->dummy_controller.ops = &flctl_nand_controller_ops; + ret = nand_scan(flctl_mtd, 1); if (ret) goto err_chip; diff --git a/drivers/mtd/nand/raw/sharpsl.c b/drivers/mtd/nand/raw/sharpsl.c index e93df02c825e..fc171b17a39b 100644 --- a/drivers/mtd/nand/raw/sharpsl.c +++ b/drivers/mtd/nand/raw/sharpsl.c @@ -21,10 +21,7 @@ #include <linux/mtd/sharpsl.h> #include <linux/interrupt.h> #include <linux/platform_device.h> - -#include <asm/io.h> -#include <mach/hardware.h> -#include <asm/mach-types.h> +#include <linux/io.h> struct sharpsl_nand { struct nand_chip chip; diff --git a/drivers/mtd/nand/raw/sm_common.c b/drivers/mtd/nand/raw/sm_common.c index 7f5044a79f01..73aafe8c3ef3 100644 --- a/drivers/mtd/nand/raw/sm_common.c +++ b/drivers/mtd/nand/raw/sm_common.c @@ -160,19 +160,9 @@ static struct nand_flash_dev nand_xd_flash_ids[] = { {NULL} }; -int sm_register_device(struct mtd_info *mtd, int smartmedia) +static int sm_attach_chip(struct nand_chip *chip) { - struct nand_chip *chip = mtd_to_nand(mtd); - int ret; - - chip->options |= NAND_SKIP_BBTSCAN; - - /* Scan for card properties */ - ret = nand_scan_ident(mtd, 1, smartmedia ? - nand_smartmedia_flash_ids : nand_xd_flash_ids); - - if (ret) - return ret; + struct mtd_info *mtd = nand_to_mtd(chip); /* Bad block marker position */ chip->badblockpos = 0x05; @@ -187,12 +177,33 @@ int sm_register_device(struct mtd_info *mtd, int smartmedia) else return -ENODEV; - ret = nand_scan_tail(mtd); + return 0; +} + +static const struct nand_controller_ops sm_controller_ops = { + .attach_chip = sm_attach_chip, +}; + +int sm_register_device(struct mtd_info *mtd, int smartmedia) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct nand_flash_dev *flash_ids; + int ret; + + chip->options |= NAND_SKIP_BBTSCAN; + /* Scan for card properties */ + chip->dummy_controller.ops = &sm_controller_ops; + flash_ids = smartmedia ? nand_smartmedia_flash_ids : nand_xd_flash_ids; + ret = nand_scan_with_ids(mtd, 1, flash_ids); if (ret) return ret; - return mtd_device_register(mtd, NULL, 0); + ret = mtd_device_register(mtd, NULL, 0); + if (ret) + nand_cleanup(chip); + + return ret; } EXPORT_SYMBOL_GPL(sm_register_device); diff --git a/drivers/mtd/nand/raw/sunxi_nand.c b/drivers/mtd/nand/raw/sunxi_nand.c index d831a141a196..1f0b7ee38df5 100644 --- a/drivers/mtd/nand/raw/sunxi_nand.c +++ b/drivers/mtd/nand/raw/sunxi_nand.c @@ -29,14 +29,12 @@ #include <linux/platform_device.h> #include <linux/of.h> #include <linux/of_device.h> -#include <linux/of_gpio.h> #include <linux/mtd/mtd.h> #include <linux/mtd/rawnand.h> #include <linux/mtd/partitions.h> #include <linux/clk.h> #include <linux/delay.h> #include <linux/dmaengine.h> -#include <linux/gpio.h> #include <linux/interrupt.h> #include <linux/iopoll.h> #include <linux/reset.h> @@ -127,7 +125,7 @@ #define NFC_CMD_TYPE_MSK GENMASK(31, 30) #define NFC_NORMAL_OP (0 << 30) #define NFC_ECC_OP (1 << 30) -#define NFC_PAGE_OP (2 << 30) +#define NFC_PAGE_OP (2U << 30) /* define bit use in NFC_RCMD_SET */ #define NFC_READ_CMD_MSK GENMASK(7, 0) @@ -234,7 +232,7 @@ static inline struct sunxi_nand_chip *to_sunxi_nand(struct nand_chip *nand) * controller events */ struct sunxi_nfc { - struct nand_hw_control controller; + struct nand_controller controller; struct device *dev; void __iomem *regs; struct clk *ahb_clk; @@ -247,7 +245,7 @@ struct sunxi_nfc { struct dma_chan *dmac; }; -static inline struct sunxi_nfc *to_sunxi_nfc(struct nand_hw_control *ctrl) +static inline struct sunxi_nfc *to_sunxi_nfc(struct nand_controller *ctrl) { return container_of(ctrl, struct sunxi_nfc, controller); } @@ -544,7 +542,7 @@ static void sunxi_nfc_write_buf(struct mtd_info *mtd, const uint8_t *buf, static uint8_t sunxi_nfc_read_byte(struct mtd_info *mtd) { - uint8_t ret; + uint8_t ret = 0; sunxi_nfc_read_buf(mtd, &ret, 1); @@ -1816,12 +1814,21 @@ static void sunxi_nand_ecc_cleanup(struct nand_ecc_ctrl *ecc) } } -static int sunxi_nand_ecc_init(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc, - struct device_node *np) +static int sunxi_nand_attach_chip(struct nand_chip *nand) { - struct nand_chip *nand = mtd_to_nand(mtd); + struct mtd_info *mtd = nand_to_mtd(nand); + struct nand_ecc_ctrl *ecc = &nand->ecc; + struct device_node *np = nand_get_flash_node(nand); int ret; + if (nand->bbt_options & NAND_BBT_USE_FLASH) + nand->bbt_options |= NAND_BBT_NO_OOB; + + if (nand->options & NAND_NEED_SCRAMBLING) + nand->options |= NAND_NO_SUBPAGE_WRITE; + + nand->options |= NAND_SUBPAGE_READ; + if (!ecc->size) { ecc->size = nand->ecc_step_ds; ecc->strength = nand->ecc_strength_ds; @@ -1846,6 +1853,10 @@ static int sunxi_nand_ecc_init(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc, return 0; } +static const struct nand_controller_ops sunxi_nand_controller_ops = { + .attach_chip = sunxi_nand_attach_chip, +}; + static int sunxi_nand_chip_init(struct device *dev, struct sunxi_nfc *nfc, struct device_node *np) { @@ -1911,6 +1922,8 @@ static int sunxi_nand_chip_init(struct device *dev, struct sunxi_nfc *nfc, /* Default tR value specified in the ONFI spec (chapter 4.15.1) */ nand->chip_delay = 200; nand->controller = &nfc->controller; + nand->controller->ops = &sunxi_nand_controller_ops; + /* * Set the ECC mode to the default value in case nothing is specified * in the DT. @@ -1927,30 +1940,10 @@ static int sunxi_nand_chip_init(struct device *dev, struct sunxi_nfc *nfc, mtd = nand_to_mtd(nand); mtd->dev.parent = dev; - ret = nand_scan_ident(mtd, nsels, NULL); + ret = nand_scan(mtd, nsels); if (ret) return ret; - if (nand->bbt_options & NAND_BBT_USE_FLASH) - nand->bbt_options |= NAND_BBT_NO_OOB; - - if (nand->options & NAND_NEED_SCRAMBLING) - nand->options |= NAND_NO_SUBPAGE_WRITE; - - nand->options |= NAND_SUBPAGE_READ; - - ret = sunxi_nand_ecc_init(mtd, &nand->ecc, np); - if (ret) { - dev_err(dev, "ECC init failed: %d\n", ret); - return ret; - } - - ret = nand_scan_tail(mtd); - if (ret) { - dev_err(dev, "nand_scan_tail failed: %d\n", ret); - return ret; - } - ret = mtd_device_register(mtd, NULL, 0); if (ret) { dev_err(dev, "failed to register mtd device: %d\n", ret); @@ -2012,7 +2005,7 @@ static int sunxi_nfc_probe(struct platform_device *pdev) return -ENOMEM; nfc->dev = dev; - nand_hw_control_init(&nfc->controller); + nand_controller_init(&nfc->controller); INIT_LIST_HEAD(&nfc->chips); r = platform_get_resource(pdev, IORESOURCE_MEM, 0); diff --git a/drivers/mtd/nand/raw/tango_nand.c b/drivers/mtd/nand/raw/tango_nand.c index f2052fae21c7..72698691727d 100644 --- a/drivers/mtd/nand/raw/tango_nand.c +++ b/drivers/mtd/nand/raw/tango_nand.c @@ -83,7 +83,7 @@ #define MAX_CS 4 struct tango_nfc { - struct nand_hw_control hw; + struct nand_controller hw; void __iomem *reg_base; void __iomem *mem_base; void __iomem *pbus_base; @@ -517,6 +517,28 @@ static int tango_set_timings(struct mtd_info *mtd, int csline, return 0; } +static int tango_attach_chip(struct nand_chip *chip) +{ + struct nand_ecc_ctrl *ecc = &chip->ecc; + + ecc->mode = NAND_ECC_HW; + ecc->algo = NAND_ECC_BCH; + ecc->bytes = DIV_ROUND_UP(ecc->strength * FIELD_ORDER, BITS_PER_BYTE); + + ecc->read_page_raw = tango_read_page_raw; + ecc->write_page_raw = tango_write_page_raw; + ecc->read_page = tango_read_page; + ecc->write_page = tango_write_page; + ecc->read_oob = tango_read_oob; + ecc->write_oob = tango_write_oob; + + return 0; +} + +static const struct nand_controller_ops tango_controller_ops = { + .attach_chip = tango_attach_chip, +}; + static int chip_init(struct device *dev, struct device_node *np) { u32 cs; @@ -566,22 +588,7 @@ static int chip_init(struct device *dev, struct device_node *np) mtd_set_ooblayout(mtd, &tango_nand_ooblayout_ops); mtd->dev.parent = dev; - err = nand_scan_ident(mtd, 1, NULL); - if (err) - return err; - - ecc->mode = NAND_ECC_HW; - ecc->algo = NAND_ECC_BCH; - ecc->bytes = DIV_ROUND_UP(ecc->strength * FIELD_ORDER, BITS_PER_BYTE); - - ecc->read_page_raw = tango_read_page_raw; - ecc->write_page_raw = tango_write_page_raw; - ecc->read_page = tango_read_page; - ecc->write_page = tango_write_page; - ecc->read_oob = tango_read_oob; - ecc->write_oob = tango_write_oob; - - err = nand_scan_tail(mtd); + err = nand_scan(mtd, 1); if (err) return err; @@ -654,7 +661,8 @@ static int tango_nand_probe(struct platform_device *pdev) return PTR_ERR(nfc->chan); platform_set_drvdata(pdev, nfc); - nand_hw_control_init(&nfc->hw); + nand_controller_init(&nfc->hw); + nfc->hw.ops = &tango_controller_ops; nfc->freq_kHz = clk_get_rate(clk) / 1000; for_each_child_of_node(pdev->dev.of_node, np) { diff --git a/drivers/mtd/nand/raw/tegra_nand.c b/drivers/mtd/nand/raw/tegra_nand.c new file mode 100644 index 000000000000..79da1efc88d1 --- /dev/null +++ b/drivers/mtd/nand/raw/tegra_nand.c @@ -0,0 +1,1246 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2018 Stefan Agner <stefan@agner.ch> + * Copyright (C) 2014-2015 Lucas Stach <dev@lynxeye.de> + * Copyright (C) 2012 Avionic Design GmbH + */ + +#include <linux/clk.h> +#include <linux/completion.h> +#include <linux/dma-mapping.h> +#include <linux/err.h> +#include <linux/gpio/consumer.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/rawnand.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/reset.h> + +#define COMMAND 0x00 +#define COMMAND_GO BIT(31) +#define COMMAND_CLE BIT(30) +#define COMMAND_ALE BIT(29) +#define COMMAND_PIO BIT(28) +#define COMMAND_TX BIT(27) +#define COMMAND_RX BIT(26) +#define COMMAND_SEC_CMD BIT(25) +#define COMMAND_AFT_DAT BIT(24) +#define COMMAND_TRANS_SIZE(size) ((((size) - 1) & 0xf) << 20) +#define COMMAND_A_VALID BIT(19) +#define COMMAND_B_VALID BIT(18) +#define COMMAND_RD_STATUS_CHK BIT(17) +#define COMMAND_RBSY_CHK BIT(16) +#define COMMAND_CE(x) BIT(8 + ((x) & 0x7)) +#define COMMAND_CLE_SIZE(size) ((((size) - 1) & 0x3) << 4) +#define COMMAND_ALE_SIZE(size) ((((size) - 1) & 0xf) << 0) + +#define STATUS 0x04 + +#define ISR 0x08 +#define ISR_CORRFAIL_ERR BIT(24) +#define ISR_UND BIT(7) +#define ISR_OVR BIT(6) +#define ISR_CMD_DONE BIT(5) +#define ISR_ECC_ERR BIT(4) + +#define IER 0x0c +#define IER_ERR_TRIG_VAL(x) (((x) & 0xf) << 16) +#define IER_UND BIT(7) +#define IER_OVR BIT(6) +#define IER_CMD_DONE BIT(5) +#define IER_ECC_ERR BIT(4) +#define IER_GIE BIT(0) + +#define CONFIG 0x10 +#define CONFIG_HW_ECC BIT(31) +#define CONFIG_ECC_SEL BIT(30) +#define CONFIG_ERR_COR BIT(29) +#define CONFIG_PIPE_EN BIT(28) +#define CONFIG_TVAL_4 (0 << 24) +#define CONFIG_TVAL_6 (1 << 24) +#define CONFIG_TVAL_8 (2 << 24) +#define CONFIG_SKIP_SPARE BIT(23) +#define CONFIG_BUS_WIDTH_16 BIT(21) +#define CONFIG_COM_BSY BIT(20) +#define CONFIG_PS_256 (0 << 16) +#define CONFIG_PS_512 (1 << 16) +#define CONFIG_PS_1024 (2 << 16) +#define CONFIG_PS_2048 (3 << 16) +#define CONFIG_PS_4096 (4 << 16) +#define CONFIG_SKIP_SPARE_SIZE_4 (0 << 14) +#define CONFIG_SKIP_SPARE_SIZE_8 (1 << 14) +#define CONFIG_SKIP_SPARE_SIZE_12 (2 << 14) +#define CONFIG_SKIP_SPARE_SIZE_16 (3 << 14) +#define CONFIG_TAG_BYTE_SIZE(x) ((x) & 0xff) + +#define TIMING_1 0x14 +#define TIMING_TRP_RESP(x) (((x) & 0xf) << 28) +#define TIMING_TWB(x) (((x) & 0xf) << 24) +#define TIMING_TCR_TAR_TRR(x) (((x) & 0xf) << 20) +#define TIMING_TWHR(x) (((x) & 0xf) << 16) +#define TIMING_TCS(x) (((x) & 0x3) << 14) +#define TIMING_TWH(x) (((x) & 0x3) << 12) +#define TIMING_TWP(x) (((x) & 0xf) << 8) +#define TIMING_TRH(x) (((x) & 0x3) << 4) +#define TIMING_TRP(x) (((x) & 0xf) << 0) + +#define RESP 0x18 + +#define TIMING_2 0x1c +#define TIMING_TADL(x) ((x) & 0xf) + +#define CMD_REG1 0x20 +#define CMD_REG2 0x24 +#define ADDR_REG1 0x28 +#define ADDR_REG2 0x2c + +#define DMA_MST_CTRL 0x30 +#define DMA_MST_CTRL_GO BIT(31) +#define DMA_MST_CTRL_IN (0 << 30) +#define DMA_MST_CTRL_OUT BIT(30) +#define DMA_MST_CTRL_PERF_EN BIT(29) +#define DMA_MST_CTRL_IE_DONE BIT(28) +#define DMA_MST_CTRL_REUSE BIT(27) +#define DMA_MST_CTRL_BURST_1 (2 << 24) +#define DMA_MST_CTRL_BURST_4 (3 << 24) +#define DMA_MST_CTRL_BURST_8 (4 << 24) +#define DMA_MST_CTRL_BURST_16 (5 << 24) +#define DMA_MST_CTRL_IS_DONE BIT(20) +#define DMA_MST_CTRL_EN_A BIT(2) +#define DMA_MST_CTRL_EN_B BIT(1) + +#define DMA_CFG_A 0x34 +#define DMA_CFG_B 0x38 + +#define FIFO_CTRL 0x3c +#define FIFO_CTRL_CLR_ALL BIT(3) + +#define DATA_PTR 0x40 +#define TAG_PTR 0x44 +#define ECC_PTR 0x48 + +#define DEC_STATUS 0x4c +#define DEC_STATUS_A_ECC_FAIL BIT(1) +#define DEC_STATUS_ERR_COUNT_MASK 0x00ff0000 +#define DEC_STATUS_ERR_COUNT_SHIFT 16 + +#define HWSTATUS_CMD 0x50 +#define HWSTATUS_MASK 0x54 +#define HWSTATUS_RDSTATUS_MASK(x) (((x) & 0xff) << 24) +#define HWSTATUS_RDSTATUS_VALUE(x) (((x) & 0xff) << 16) +#define HWSTATUS_RBSY_MASK(x) (((x) & 0xff) << 8) +#define HWSTATUS_RBSY_VALUE(x) (((x) & 0xff) << 0) + +#define BCH_CONFIG 0xcc +#define BCH_ENABLE BIT(0) +#define BCH_TVAL_4 (0 << 4) +#define BCH_TVAL_8 (1 << 4) +#define BCH_TVAL_14 (2 << 4) +#define BCH_TVAL_16 (3 << 4) + +#define DEC_STAT_RESULT 0xd0 +#define DEC_STAT_BUF 0xd4 +#define DEC_STAT_BUF_FAIL_SEC_FLAG_MASK 0xff000000 +#define DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT 24 +#define DEC_STAT_BUF_CORR_SEC_FLAG_MASK 0x00ff0000 +#define DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT 16 +#define DEC_STAT_BUF_MAX_CORR_CNT_MASK 0x00001f00 +#define DEC_STAT_BUF_MAX_CORR_CNT_SHIFT 8 + +#define OFFSET(val, off) ((val) < (off) ? 0 : (val) - (off)) + +#define SKIP_SPARE_BYTES 4 +#define BITS_PER_STEP_RS 18 +#define BITS_PER_STEP_BCH 13 + +#define INT_MASK (IER_UND | IER_OVR | IER_CMD_DONE | IER_GIE) +#define HWSTATUS_CMD_DEFAULT NAND_STATUS_READY +#define HWSTATUS_MASK_DEFAULT (HWSTATUS_RDSTATUS_MASK(1) | \ + HWSTATUS_RDSTATUS_VALUE(0) | \ + HWSTATUS_RBSY_MASK(NAND_STATUS_READY) | \ + HWSTATUS_RBSY_VALUE(NAND_STATUS_READY)) + +struct tegra_nand_controller { + struct nand_controller controller; + struct device *dev; + void __iomem *regs; + int irq; + struct clk *clk; + struct completion command_complete; + struct completion dma_complete; + bool last_read_error; + int cur_cs; + struct nand_chip *chip; +}; + +struct tegra_nand_chip { + struct nand_chip chip; + struct gpio_desc *wp_gpio; + struct mtd_oob_region ecc; + u32 config; + u32 config_ecc; + u32 bch_config; + int cs[1]; +}; + +static inline struct tegra_nand_controller * + to_tegra_ctrl(struct nand_controller *hw_ctrl) +{ + return container_of(hw_ctrl, struct tegra_nand_controller, controller); +} + +static inline struct tegra_nand_chip *to_tegra_chip(struct nand_chip *chip) +{ + return container_of(chip, struct tegra_nand_chip, chip); +} + +static int tegra_nand_ooblayout_rs_ecc(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobregion) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_RS * chip->ecc.strength, + BITS_PER_BYTE); + + if (section > 0) + return -ERANGE; + + oobregion->offset = SKIP_SPARE_BYTES; + oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4); + + return 0; +} + +static int tegra_nand_ooblayout_no_free(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobregion) +{ + return -ERANGE; +} + +static const struct mtd_ooblayout_ops tegra_nand_oob_rs_ops = { + .ecc = tegra_nand_ooblayout_rs_ecc, + .free = tegra_nand_ooblayout_no_free, +}; + +static int tegra_nand_ooblayout_bch_ecc(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobregion) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + int bytes_per_step = DIV_ROUND_UP(BITS_PER_STEP_BCH * chip->ecc.strength, + BITS_PER_BYTE); + + if (section > 0) + return -ERANGE; + + oobregion->offset = SKIP_SPARE_BYTES; + oobregion->length = round_up(bytes_per_step * chip->ecc.steps, 4); + + return 0; +} + +static const struct mtd_ooblayout_ops tegra_nand_oob_bch_ops = { + .ecc = tegra_nand_ooblayout_bch_ecc, + .free = tegra_nand_ooblayout_no_free, +}; + +static irqreturn_t tegra_nand_irq(int irq, void *data) +{ + struct tegra_nand_controller *ctrl = data; + u32 isr, dma; + + isr = readl_relaxed(ctrl->regs + ISR); + dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL); + dev_dbg(ctrl->dev, "isr %08x\n", isr); + + if (!isr && !(dma & DMA_MST_CTRL_IS_DONE)) + return IRQ_NONE; + + /* + * The bit name is somewhat missleading: This is also set when + * HW ECC was successful. The data sheet states: + * Correctable OR Un-correctable errors occurred in the DMA transfer... + */ + if (isr & ISR_CORRFAIL_ERR) + ctrl->last_read_error = true; + + if (isr & ISR_CMD_DONE) + complete(&ctrl->command_complete); + + if (isr & ISR_UND) + dev_err(ctrl->dev, "FIFO underrun\n"); + + if (isr & ISR_OVR) + dev_err(ctrl->dev, "FIFO overrun\n"); + + /* handle DMA interrupts */ + if (dma & DMA_MST_CTRL_IS_DONE) { + writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL); + complete(&ctrl->dma_complete); + } + + /* clear interrupts */ + writel_relaxed(isr, ctrl->regs + ISR); + + return IRQ_HANDLED; +} + +static const char * const tegra_nand_reg_names[] = { + "COMMAND", + "STATUS", + "ISR", + "IER", + "CONFIG", + "TIMING", + NULL, + "TIMING2", + "CMD_REG1", + "CMD_REG2", + "ADDR_REG1", + "ADDR_REG2", + "DMA_MST_CTRL", + "DMA_CFG_A", + "DMA_CFG_B", + "FIFO_CTRL", +}; + +static void tegra_nand_dump_reg(struct tegra_nand_controller *ctrl) +{ + u32 reg; + int i; + + dev_err(ctrl->dev, "Tegra NAND controller register dump\n"); + for (i = 0; i < ARRAY_SIZE(tegra_nand_reg_names); i++) { + const char *reg_name = tegra_nand_reg_names[i]; + + if (!reg_name) + continue; + + reg = readl_relaxed(ctrl->regs + (i * 4)); + dev_err(ctrl->dev, "%s: 0x%08x\n", reg_name, reg); + } +} + +static void tegra_nand_controller_abort(struct tegra_nand_controller *ctrl) +{ + u32 isr, dma; + + disable_irq(ctrl->irq); + + /* Abort current command/DMA operation */ + writel_relaxed(0, ctrl->regs + DMA_MST_CTRL); + writel_relaxed(0, ctrl->regs + COMMAND); + + /* clear interrupts */ + isr = readl_relaxed(ctrl->regs + ISR); + writel_relaxed(isr, ctrl->regs + ISR); + dma = readl_relaxed(ctrl->regs + DMA_MST_CTRL); + writel_relaxed(dma, ctrl->regs + DMA_MST_CTRL); + + reinit_completion(&ctrl->command_complete); + reinit_completion(&ctrl->dma_complete); + + enable_irq(ctrl->irq); +} + +static int tegra_nand_cmd(struct nand_chip *chip, + const struct nand_subop *subop) +{ + const struct nand_op_instr *instr; + const struct nand_op_instr *instr_data_in = NULL; + struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller); + unsigned int op_id, size = 0, offset = 0; + bool first_cmd = true; + u32 reg, cmd = 0; + int ret; + + for (op_id = 0; op_id < subop->ninstrs; op_id++) { + unsigned int naddrs, i; + const u8 *addrs; + u32 addr1 = 0, addr2 = 0; + + instr = &subop->instrs[op_id]; + + switch (instr->type) { + case NAND_OP_CMD_INSTR: + if (first_cmd) { + cmd |= COMMAND_CLE; + writel_relaxed(instr->ctx.cmd.opcode, + ctrl->regs + CMD_REG1); + } else { + cmd |= COMMAND_SEC_CMD; + writel_relaxed(instr->ctx.cmd.opcode, + ctrl->regs + CMD_REG2); + } + first_cmd = false; + break; + + case NAND_OP_ADDR_INSTR: + offset = nand_subop_get_addr_start_off(subop, op_id); + naddrs = nand_subop_get_num_addr_cyc(subop, op_id); + addrs = &instr->ctx.addr.addrs[offset]; + + cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs); + for (i = 0; i < min_t(unsigned int, 4, naddrs); i++) + addr1 |= *addrs++ << (BITS_PER_BYTE * i); + naddrs -= i; + for (i = 0; i < min_t(unsigned int, 4, naddrs); i++) + addr2 |= *addrs++ << (BITS_PER_BYTE * i); + + writel_relaxed(addr1, ctrl->regs + ADDR_REG1); + writel_relaxed(addr2, ctrl->regs + ADDR_REG2); + break; + + case NAND_OP_DATA_IN_INSTR: + size = nand_subop_get_data_len(subop, op_id); + offset = nand_subop_get_data_start_off(subop, op_id); + + cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO | + COMMAND_RX | COMMAND_A_VALID; + + instr_data_in = instr; + break; + + case NAND_OP_DATA_OUT_INSTR: + size = nand_subop_get_data_len(subop, op_id); + offset = nand_subop_get_data_start_off(subop, op_id); + + cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO | + COMMAND_TX | COMMAND_A_VALID; + memcpy(®, instr->ctx.data.buf.out + offset, size); + + writel_relaxed(reg, ctrl->regs + RESP); + break; + + case NAND_OP_WAITRDY_INSTR: + cmd |= COMMAND_RBSY_CHK; + break; + } + } + + cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs); + writel_relaxed(cmd, ctrl->regs + COMMAND); + ret = wait_for_completion_timeout(&ctrl->command_complete, + msecs_to_jiffies(500)); + if (!ret) { + dev_err(ctrl->dev, "COMMAND timeout\n"); + tegra_nand_dump_reg(ctrl); + tegra_nand_controller_abort(ctrl); + return -ETIMEDOUT; + } + + if (instr_data_in) { + reg = readl_relaxed(ctrl->regs + RESP); + memcpy(instr_data_in->ctx.data.buf.in + offset, ®, size); + } + + return 0; +} + +static const struct nand_op_parser tegra_nand_op_parser = NAND_OP_PARSER( + NAND_OP_PARSER_PATTERN(tegra_nand_cmd, + NAND_OP_PARSER_PAT_CMD_ELEM(true), + NAND_OP_PARSER_PAT_ADDR_ELEM(true, 8), + NAND_OP_PARSER_PAT_CMD_ELEM(true), + NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)), + NAND_OP_PARSER_PATTERN(tegra_nand_cmd, + NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, 4)), + NAND_OP_PARSER_PATTERN(tegra_nand_cmd, + NAND_OP_PARSER_PAT_CMD_ELEM(true), + NAND_OP_PARSER_PAT_ADDR_ELEM(true, 8), + NAND_OP_PARSER_PAT_CMD_ELEM(true), + NAND_OP_PARSER_PAT_WAITRDY_ELEM(true), + NAND_OP_PARSER_PAT_DATA_IN_ELEM(true, 4)), + ); + +static int tegra_nand_exec_op(struct nand_chip *chip, + const struct nand_operation *op, + bool check_only) +{ + return nand_op_parser_exec_op(chip, &tegra_nand_op_parser, op, + check_only); +} + +static void tegra_nand_select_chip(struct mtd_info *mtd, int die_nr) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct tegra_nand_chip *nand = to_tegra_chip(chip); + struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller); + + WARN_ON(die_nr >= (int)ARRAY_SIZE(nand->cs)); + + if (die_nr < 0 || die_nr > 0) { + ctrl->cur_cs = -1; + return; + } + + ctrl->cur_cs = nand->cs[die_nr]; +} + +static void tegra_nand_hw_ecc(struct tegra_nand_controller *ctrl, + struct nand_chip *chip, bool enable) +{ + struct tegra_nand_chip *nand = to_tegra_chip(chip); + + if (chip->ecc.algo == NAND_ECC_BCH && enable) + writel_relaxed(nand->bch_config, ctrl->regs + BCH_CONFIG); + else + writel_relaxed(0, ctrl->regs + BCH_CONFIG); + + if (enable) + writel_relaxed(nand->config_ecc, ctrl->regs + CONFIG); + else + writel_relaxed(nand->config, ctrl->regs + CONFIG); +} + +static int tegra_nand_page_xfer(struct mtd_info *mtd, struct nand_chip *chip, + void *buf, void *oob_buf, int oob_len, int page, + bool read) +{ + struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller); + enum dma_data_direction dir = read ? DMA_FROM_DEVICE : DMA_TO_DEVICE; + dma_addr_t dma_addr = 0, dma_addr_oob = 0; + u32 addr1, cmd, dma_ctrl; + int ret; + + if (read) { + writel_relaxed(NAND_CMD_READ0, ctrl->regs + CMD_REG1); + writel_relaxed(NAND_CMD_READSTART, ctrl->regs + CMD_REG2); + } else { + writel_relaxed(NAND_CMD_SEQIN, ctrl->regs + CMD_REG1); + writel_relaxed(NAND_CMD_PAGEPROG, ctrl->regs + CMD_REG2); + } + cmd = COMMAND_CLE | COMMAND_SEC_CMD; + + /* Lower 16-bits are column, by default 0 */ + addr1 = page << 16; + + if (!buf) + addr1 |= mtd->writesize; + writel_relaxed(addr1, ctrl->regs + ADDR_REG1); + + if (chip->options & NAND_ROW_ADDR_3) { + writel_relaxed(page >> 16, ctrl->regs + ADDR_REG2); + cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(5); + } else { + cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(4); + } + + if (buf) { + dma_addr = dma_map_single(ctrl->dev, buf, mtd->writesize, dir); + ret = dma_mapping_error(ctrl->dev, dma_addr); + if (ret) { + dev_err(ctrl->dev, "dma mapping error\n"); + return -EINVAL; + } + + writel_relaxed(mtd->writesize - 1, ctrl->regs + DMA_CFG_A); + writel_relaxed(dma_addr, ctrl->regs + DATA_PTR); + } + + if (oob_buf) { + dma_addr_oob = dma_map_single(ctrl->dev, oob_buf, mtd->oobsize, + dir); + ret = dma_mapping_error(ctrl->dev, dma_addr_oob); + if (ret) { + dev_err(ctrl->dev, "dma mapping error\n"); + ret = -EINVAL; + goto err_unmap_dma_page; + } + + writel_relaxed(oob_len - 1, ctrl->regs + DMA_CFG_B); + writel_relaxed(dma_addr_oob, ctrl->regs + TAG_PTR); + } + + dma_ctrl = DMA_MST_CTRL_GO | DMA_MST_CTRL_PERF_EN | + DMA_MST_CTRL_IE_DONE | DMA_MST_CTRL_IS_DONE | + DMA_MST_CTRL_BURST_16; + + if (buf) + dma_ctrl |= DMA_MST_CTRL_EN_A; + if (oob_buf) + dma_ctrl |= DMA_MST_CTRL_EN_B; + + if (read) + dma_ctrl |= DMA_MST_CTRL_IN | DMA_MST_CTRL_REUSE; + else + dma_ctrl |= DMA_MST_CTRL_OUT; + + writel_relaxed(dma_ctrl, ctrl->regs + DMA_MST_CTRL); + + cmd |= COMMAND_GO | COMMAND_RBSY_CHK | COMMAND_TRANS_SIZE(9) | + COMMAND_CE(ctrl->cur_cs); + + if (buf) + cmd |= COMMAND_A_VALID; + if (oob_buf) + cmd |= COMMAND_B_VALID; + + if (read) + cmd |= COMMAND_RX; + else + cmd |= COMMAND_TX | COMMAND_AFT_DAT; + + writel_relaxed(cmd, ctrl->regs + COMMAND); + + ret = wait_for_completion_timeout(&ctrl->command_complete, + msecs_to_jiffies(500)); + if (!ret) { + dev_err(ctrl->dev, "COMMAND timeout\n"); + tegra_nand_dump_reg(ctrl); + tegra_nand_controller_abort(ctrl); + ret = -ETIMEDOUT; + goto err_unmap_dma; + } + + ret = wait_for_completion_timeout(&ctrl->dma_complete, + msecs_to_jiffies(500)); + if (!ret) { + dev_err(ctrl->dev, "DMA timeout\n"); + tegra_nand_dump_reg(ctrl); + tegra_nand_controller_abort(ctrl); + ret = -ETIMEDOUT; + goto err_unmap_dma; + } + ret = 0; + +err_unmap_dma: + if (oob_buf) + dma_unmap_single(ctrl->dev, dma_addr_oob, mtd->oobsize, dir); +err_unmap_dma_page: + if (buf) + dma_unmap_single(ctrl->dev, dma_addr, mtd->writesize, dir); + + return ret; +} + +static int tegra_nand_read_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, u8 *buf, + int oob_required, int page) +{ + void *oob_buf = oob_required ? chip->oob_poi : NULL; + + return tegra_nand_page_xfer(mtd, chip, buf, oob_buf, + mtd->oobsize, page, true); +} + +static int tegra_nand_write_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, const u8 *buf, + int oob_required, int page) +{ + void *oob_buf = oob_required ? chip->oob_poi : NULL; + + return tegra_nand_page_xfer(mtd, chip, (void *)buf, oob_buf, + mtd->oobsize, page, false); +} + +static int tegra_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + return tegra_nand_page_xfer(mtd, chip, NULL, chip->oob_poi, + mtd->oobsize, page, true); +} + +static int tegra_nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + return tegra_nand_page_xfer(mtd, chip, NULL, chip->oob_poi, + mtd->oobsize, page, false); +} + +static int tegra_nand_read_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, u8 *buf, + int oob_required, int page) +{ + struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller); + struct tegra_nand_chip *nand = to_tegra_chip(chip); + void *oob_buf = oob_required ? chip->oob_poi : NULL; + u32 dec_stat, max_corr_cnt; + unsigned long fail_sec_flag; + int ret; + + tegra_nand_hw_ecc(ctrl, chip, true); + ret = tegra_nand_page_xfer(mtd, chip, buf, oob_buf, 0, page, true); + tegra_nand_hw_ecc(ctrl, chip, false); + if (ret) + return ret; + + /* No correctable or un-correctable errors, page must have 0 bitflips */ + if (!ctrl->last_read_error) + return 0; + + /* + * Correctable or un-correctable errors occurred. Use DEC_STAT_BUF + * which contains information for all ECC selections. + * + * Note that since we do not use Command Queues DEC_RESULT does not + * state the number of pages we can read from the DEC_STAT_BUF. But + * since CORRFAIL_ERR did occur during page read we do have a valid + * result in DEC_STAT_BUF. + */ + ctrl->last_read_error = false; + dec_stat = readl_relaxed(ctrl->regs + DEC_STAT_BUF); + + fail_sec_flag = (dec_stat & DEC_STAT_BUF_FAIL_SEC_FLAG_MASK) >> + DEC_STAT_BUF_FAIL_SEC_FLAG_SHIFT; + + max_corr_cnt = (dec_stat & DEC_STAT_BUF_MAX_CORR_CNT_MASK) >> + DEC_STAT_BUF_MAX_CORR_CNT_SHIFT; + + if (fail_sec_flag) { + int bit, max_bitflips = 0; + + /* + * Since we do not support subpage writes, a complete page + * is either written or not. We can take a shortcut here by + * checking wheather any of the sector has been successful + * read. If at least one sectors has been read successfully, + * the page must have been a written previously. It cannot + * be an erased page. + * + * E.g. controller might return fail_sec_flag with 0x4, which + * would mean only the third sector failed to correct. The + * page must have been written and the third sector is really + * not correctable anymore. + */ + if (fail_sec_flag ^ GENMASK(chip->ecc.steps - 1, 0)) { + mtd->ecc_stats.failed += hweight8(fail_sec_flag); + return max_corr_cnt; + } + + /* + * All sectors failed to correct, but the ECC isn't smart + * enough to figure out if a page is really just erased. + * Read OOB data and check whether data/OOB is completely + * erased or if error correction just failed for all sub- + * pages. + */ + ret = tegra_nand_read_oob(mtd, chip, page); + if (ret < 0) + return ret; + + for_each_set_bit(bit, &fail_sec_flag, chip->ecc.steps) { + u8 *data = buf + (chip->ecc.size * bit); + u8 *oob = chip->oob_poi + nand->ecc.offset + + (chip->ecc.bytes * bit); + + ret = nand_check_erased_ecc_chunk(data, chip->ecc.size, + oob, chip->ecc.bytes, + NULL, 0, + chip->ecc.strength); + if (ret < 0) { + mtd->ecc_stats.failed++; + } else { + mtd->ecc_stats.corrected += ret; + max_bitflips = max(ret, max_bitflips); + } + } + + return max_t(unsigned int, max_corr_cnt, max_bitflips); + } else { + int corr_sec_flag; + + corr_sec_flag = (dec_stat & DEC_STAT_BUF_CORR_SEC_FLAG_MASK) >> + DEC_STAT_BUF_CORR_SEC_FLAG_SHIFT; + + /* + * The value returned in the register is the maximum of + * bitflips encountered in any of the ECC regions. As there is + * no way to get the number of bitflips in a specific regions + * we are not able to deliver correct stats but instead + * overestimate the number of corrected bitflips by assuming + * that all regions where errors have been corrected + * encountered the maximum number of bitflips. + */ + mtd->ecc_stats.corrected += max_corr_cnt * hweight8(corr_sec_flag); + + return max_corr_cnt; + } +} + +static int tegra_nand_write_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, const u8 *buf, + int oob_required, int page) +{ + struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller); + void *oob_buf = oob_required ? chip->oob_poi : NULL; + int ret; + + tegra_nand_hw_ecc(ctrl, chip, true); + ret = tegra_nand_page_xfer(mtd, chip, (void *)buf, oob_buf, + 0, page, false); + tegra_nand_hw_ecc(ctrl, chip, false); + + return ret; +} + +static void tegra_nand_setup_timing(struct tegra_nand_controller *ctrl, + const struct nand_sdr_timings *timings) +{ + /* + * The period (and all other timings in this function) is in ps, + * so need to take care here to avoid integer overflows. + */ + unsigned int rate = clk_get_rate(ctrl->clk) / 1000000; + unsigned int period = DIV_ROUND_UP(1000000, rate); + u32 val, reg = 0; + + val = DIV_ROUND_UP(max3(timings->tAR_min, timings->tRR_min, + timings->tRC_min), period); + reg |= TIMING_TCR_TAR_TRR(OFFSET(val, 3)); + + val = DIV_ROUND_UP(max(max(timings->tCS_min, timings->tCH_min), + max(timings->tALS_min, timings->tALH_min)), + period); + reg |= TIMING_TCS(OFFSET(val, 2)); + + val = DIV_ROUND_UP(max(timings->tRP_min, timings->tREA_max) + 6000, + period); + reg |= TIMING_TRP(OFFSET(val, 1)) | TIMING_TRP_RESP(OFFSET(val, 1)); + + reg |= TIMING_TWB(OFFSET(DIV_ROUND_UP(timings->tWB_max, period), 1)); + reg |= TIMING_TWHR(OFFSET(DIV_ROUND_UP(timings->tWHR_min, period), 1)); + reg |= TIMING_TWH(OFFSET(DIV_ROUND_UP(timings->tWH_min, period), 1)); + reg |= TIMING_TWP(OFFSET(DIV_ROUND_UP(timings->tWP_min, period), 1)); + reg |= TIMING_TRH(OFFSET(DIV_ROUND_UP(timings->tREH_min, period), 1)); + + writel_relaxed(reg, ctrl->regs + TIMING_1); + + val = DIV_ROUND_UP(timings->tADL_min, period); + reg = TIMING_TADL(OFFSET(val, 3)); + + writel_relaxed(reg, ctrl->regs + TIMING_2); +} + +static int tegra_nand_setup_data_interface(struct mtd_info *mtd, int csline, + const struct nand_data_interface *conf) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller); + const struct nand_sdr_timings *timings; + + timings = nand_get_sdr_timings(conf); + if (IS_ERR(timings)) + return PTR_ERR(timings); + + if (csline == NAND_DATA_IFACE_CHECK_ONLY) + return 0; + + tegra_nand_setup_timing(ctrl, timings); + + return 0; +} + +static const int rs_strength_bootable[] = { 4 }; +static const int rs_strength[] = { 4, 6, 8 }; +static const int bch_strength_bootable[] = { 8, 16 }; +static const int bch_strength[] = { 4, 8, 14, 16 }; + +static int tegra_nand_get_strength(struct nand_chip *chip, const int *strength, + int strength_len, int bits_per_step, + int oobsize) +{ + bool maximize = chip->ecc.options & NAND_ECC_MAXIMIZE; + int i; + + /* + * Loop through available strengths. Backwards in case we try to + * maximize the BCH strength. + */ + for (i = 0; i < strength_len; i++) { + int strength_sel, bytes_per_step, bytes_per_page; + + if (maximize) { + strength_sel = strength[strength_len - i - 1]; + } else { + strength_sel = strength[i]; + + if (strength_sel < chip->ecc_strength_ds) + continue; + } + + bytes_per_step = DIV_ROUND_UP(bits_per_step * strength_sel, + BITS_PER_BYTE); + bytes_per_page = round_up(bytes_per_step * chip->ecc.steps, 4); + + /* Check whether strength fits OOB */ + if (bytes_per_page < (oobsize - SKIP_SPARE_BYTES)) + return strength_sel; + } + + return -EINVAL; +} + +static int tegra_nand_select_strength(struct nand_chip *chip, int oobsize) +{ + const int *strength; + int strength_len, bits_per_step; + + switch (chip->ecc.algo) { + case NAND_ECC_RS: + bits_per_step = BITS_PER_STEP_RS; + if (chip->options & NAND_IS_BOOT_MEDIUM) { + strength = rs_strength_bootable; + strength_len = ARRAY_SIZE(rs_strength_bootable); + } else { + strength = rs_strength; + strength_len = ARRAY_SIZE(rs_strength); + } + break; + case NAND_ECC_BCH: + bits_per_step = BITS_PER_STEP_BCH; + if (chip->options & NAND_IS_BOOT_MEDIUM) { + strength = bch_strength_bootable; + strength_len = ARRAY_SIZE(bch_strength_bootable); + } else { + strength = bch_strength; + strength_len = ARRAY_SIZE(bch_strength); + } + break; + default: + return -EINVAL; + } + + return tegra_nand_get_strength(chip, strength, strength_len, + bits_per_step, oobsize); +} + +static int tegra_nand_attach_chip(struct nand_chip *chip) +{ + struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller); + struct tegra_nand_chip *nand = to_tegra_chip(chip); + struct mtd_info *mtd = nand_to_mtd(chip); + int bits_per_step; + int ret; + + if (chip->bbt_options & NAND_BBT_USE_FLASH) + chip->bbt_options |= NAND_BBT_NO_OOB; + + chip->ecc.mode = NAND_ECC_HW; + chip->ecc.size = 512; + chip->ecc.steps = mtd->writesize / chip->ecc.size; + if (chip->ecc_step_ds != 512) { + dev_err(ctrl->dev, "Unsupported step size %d\n", + chip->ecc_step_ds); + return -EINVAL; + } + + chip->ecc.read_page = tegra_nand_read_page_hwecc; + chip->ecc.write_page = tegra_nand_write_page_hwecc; + chip->ecc.read_page_raw = tegra_nand_read_page_raw; + chip->ecc.write_page_raw = tegra_nand_write_page_raw; + chip->ecc.read_oob = tegra_nand_read_oob; + chip->ecc.write_oob = tegra_nand_write_oob; + + if (chip->options & NAND_BUSWIDTH_16) + nand->config |= CONFIG_BUS_WIDTH_16; + + if (chip->ecc.algo == NAND_ECC_UNKNOWN) { + if (mtd->writesize < 2048) + chip->ecc.algo = NAND_ECC_RS; + else + chip->ecc.algo = NAND_ECC_BCH; + } + + if (chip->ecc.algo == NAND_ECC_BCH && mtd->writesize < 2048) { + dev_err(ctrl->dev, "BCH supports 2K or 4K page size only\n"); + return -EINVAL; + } + + if (!chip->ecc.strength) { + ret = tegra_nand_select_strength(chip, mtd->oobsize); + if (ret < 0) { + dev_err(ctrl->dev, + "No valid strength found, minimum %d\n", + chip->ecc_strength_ds); + return ret; + } + + chip->ecc.strength = ret; + } + + nand->config_ecc = CONFIG_PIPE_EN | CONFIG_SKIP_SPARE | + CONFIG_SKIP_SPARE_SIZE_4; + + switch (chip->ecc.algo) { + case NAND_ECC_RS: + bits_per_step = BITS_PER_STEP_RS * chip->ecc.strength; + mtd_set_ooblayout(mtd, &tegra_nand_oob_rs_ops); + nand->config_ecc |= CONFIG_HW_ECC | CONFIG_ECC_SEL | + CONFIG_ERR_COR; + switch (chip->ecc.strength) { + case 4: + nand->config_ecc |= CONFIG_TVAL_4; + break; + case 6: + nand->config_ecc |= CONFIG_TVAL_6; + break; + case 8: + nand->config_ecc |= CONFIG_TVAL_8; + break; + default: + dev_err(ctrl->dev, "ECC strength %d not supported\n", + chip->ecc.strength); + return -EINVAL; + } + break; + case NAND_ECC_BCH: + bits_per_step = BITS_PER_STEP_BCH * chip->ecc.strength; + mtd_set_ooblayout(mtd, &tegra_nand_oob_bch_ops); + nand->bch_config = BCH_ENABLE; + switch (chip->ecc.strength) { + case 4: + nand->bch_config |= BCH_TVAL_4; + break; + case 8: + nand->bch_config |= BCH_TVAL_8; + break; + case 14: + nand->bch_config |= BCH_TVAL_14; + break; + case 16: + nand->bch_config |= BCH_TVAL_16; + break; + default: + dev_err(ctrl->dev, "ECC strength %d not supported\n", + chip->ecc.strength); + return -EINVAL; + } + break; + default: + dev_err(ctrl->dev, "ECC algorithm not supported\n"); + return -EINVAL; + } + + dev_info(ctrl->dev, "Using %s with strength %d per 512 byte step\n", + chip->ecc.algo == NAND_ECC_BCH ? "BCH" : "RS", + chip->ecc.strength); + + chip->ecc.bytes = DIV_ROUND_UP(bits_per_step, BITS_PER_BYTE); + + switch (mtd->writesize) { + case 256: + nand->config |= CONFIG_PS_256; + break; + case 512: + nand->config |= CONFIG_PS_512; + break; + case 1024: + nand->config |= CONFIG_PS_1024; + break; + case 2048: + nand->config |= CONFIG_PS_2048; + break; + case 4096: + nand->config |= CONFIG_PS_4096; + break; + default: + dev_err(ctrl->dev, "Unsupported writesize %d\n", + mtd->writesize); + return -ENODEV; + } + + /* Store complete configuration for HW ECC in config_ecc */ + nand->config_ecc |= nand->config; + + /* Non-HW ECC read/writes complete OOB */ + nand->config |= CONFIG_TAG_BYTE_SIZE(mtd->oobsize - 1); + writel_relaxed(nand->config, ctrl->regs + CONFIG); + + return 0; +} + +static const struct nand_controller_ops tegra_nand_controller_ops = { + .attach_chip = &tegra_nand_attach_chip, +}; + +static int tegra_nand_chips_init(struct device *dev, + struct tegra_nand_controller *ctrl) +{ + struct device_node *np = dev->of_node; + struct device_node *np_nand; + int nsels, nchips = of_get_child_count(np); + struct tegra_nand_chip *nand; + struct mtd_info *mtd; + struct nand_chip *chip; + int ret; + u32 cs; + + if (nchips != 1) { + dev_err(dev, "Currently only one NAND chip supported\n"); + return -EINVAL; + } + + np_nand = of_get_next_child(np, NULL); + + nsels = of_property_count_elems_of_size(np_nand, "reg", sizeof(u32)); + if (nsels != 1) { + dev_err(dev, "Missing/invalid reg property\n"); + return -EINVAL; + } + + /* Retrieve CS id, currently only single die NAND supported */ + ret = of_property_read_u32(np_nand, "reg", &cs); + if (ret) { + dev_err(dev, "could not retrieve reg property: %d\n", ret); + return ret; + } + + nand = devm_kzalloc(dev, sizeof(*nand), GFP_KERNEL); + if (!nand) + return -ENOMEM; + + nand->cs[0] = cs; + + nand->wp_gpio = devm_gpiod_get_optional(dev, "wp", GPIOD_OUT_LOW); + + if (IS_ERR(nand->wp_gpio)) { + ret = PTR_ERR(nand->wp_gpio); + dev_err(dev, "Failed to request WP GPIO: %d\n", ret); + return ret; + } + + chip = &nand->chip; + chip->controller = &ctrl->controller; + + mtd = nand_to_mtd(chip); + + mtd->dev.parent = dev; + mtd->owner = THIS_MODULE; + + nand_set_flash_node(chip, np_nand); + + if (!mtd->name) + mtd->name = "tegra_nand"; + + chip->options = NAND_NO_SUBPAGE_WRITE | NAND_USE_BOUNCE_BUFFER; + chip->exec_op = tegra_nand_exec_op; + chip->select_chip = tegra_nand_select_chip; + chip->setup_data_interface = tegra_nand_setup_data_interface; + + ret = nand_scan(mtd, 1); + if (ret) + return ret; + + mtd_ooblayout_ecc(mtd, 0, &nand->ecc); + + ret = mtd_device_register(mtd, NULL, 0); + if (ret) { + dev_err(dev, "Failed to register mtd device: %d\n", ret); + nand_cleanup(chip); + return ret; + } + + ctrl->chip = chip; + + return 0; +} + +static int tegra_nand_probe(struct platform_device *pdev) +{ + struct reset_control *rst; + struct tegra_nand_controller *ctrl; + struct resource *res; + int err = 0; + + ctrl = devm_kzalloc(&pdev->dev, sizeof(*ctrl), GFP_KERNEL); + if (!ctrl) + return -ENOMEM; + + ctrl->dev = &pdev->dev; + nand_controller_init(&ctrl->controller); + ctrl->controller.ops = &tegra_nand_controller_ops; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + ctrl->regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(ctrl->regs)) + return PTR_ERR(ctrl->regs); + + rst = devm_reset_control_get(&pdev->dev, "nand"); + if (IS_ERR(rst)) + return PTR_ERR(rst); + + ctrl->clk = devm_clk_get(&pdev->dev, "nand"); + if (IS_ERR(ctrl->clk)) + return PTR_ERR(ctrl->clk); + + err = clk_prepare_enable(ctrl->clk); + if (err) + return err; + + err = reset_control_reset(rst); + if (err) { + dev_err(ctrl->dev, "Failed to reset HW: %d\n", err); + goto err_disable_clk; + } + + writel_relaxed(HWSTATUS_CMD_DEFAULT, ctrl->regs + HWSTATUS_CMD); + writel_relaxed(HWSTATUS_MASK_DEFAULT, ctrl->regs + HWSTATUS_MASK); + writel_relaxed(INT_MASK, ctrl->regs + IER); + + init_completion(&ctrl->command_complete); + init_completion(&ctrl->dma_complete); + + ctrl->irq = platform_get_irq(pdev, 0); + err = devm_request_irq(&pdev->dev, ctrl->irq, tegra_nand_irq, 0, + dev_name(&pdev->dev), ctrl); + if (err) { + dev_err(ctrl->dev, "Failed to get IRQ: %d\n", err); + goto err_disable_clk; + } + + writel_relaxed(DMA_MST_CTRL_IS_DONE, ctrl->regs + DMA_MST_CTRL); + + err = tegra_nand_chips_init(ctrl->dev, ctrl); + if (err) + goto err_disable_clk; + + platform_set_drvdata(pdev, ctrl); + + return 0; + +err_disable_clk: + clk_disable_unprepare(ctrl->clk); + return err; +} + +static int tegra_nand_remove(struct platform_device *pdev) +{ + struct tegra_nand_controller *ctrl = platform_get_drvdata(pdev); + struct nand_chip *chip = ctrl->chip; + struct mtd_info *mtd = nand_to_mtd(chip); + int ret; + + ret = mtd_device_unregister(mtd); + if (ret) + return ret; + + nand_cleanup(chip); + + clk_disable_unprepare(ctrl->clk); + + return 0; +} + +static const struct of_device_id tegra_nand_of_match[] = { + { .compatible = "nvidia,tegra20-nand" }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, tegra_nand_of_match); + +static struct platform_driver tegra_nand_driver = { + .driver = { + .name = "tegra-nand", + .of_match_table = tegra_nand_of_match, + }, + .probe = tegra_nand_probe, + .remove = tegra_nand_remove, +}; +module_platform_driver(tegra_nand_driver); + +MODULE_DESCRIPTION("NVIDIA Tegra NAND driver"); +MODULE_AUTHOR("Thierry Reding <thierry.reding@nvidia.com>"); +MODULE_AUTHOR("Lucas Stach <dev@lynxeye.de>"); +MODULE_AUTHOR("Stefan Agner <stefan@agner.ch>"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/mtd/nand/raw/txx9ndfmc.c b/drivers/mtd/nand/raw/txx9ndfmc.c index b567d212fe7d..4d61a14fcb65 100644 --- a/drivers/mtd/nand/raw/txx9ndfmc.c +++ b/drivers/mtd/nand/raw/txx9ndfmc.c @@ -20,7 +20,7 @@ #include <linux/mtd/nand_ecc.h> #include <linux/mtd/partitions.h> #include <linux/io.h> -#include <asm/txx9/ndfmc.h> +#include <linux/platform_data/txx9/ndfmc.h> /* TXX9 NDFMC Registers */ #define TXX9_NDFDTR 0x00 @@ -73,7 +73,7 @@ struct txx9ndfmc_drvdata { void __iomem *base; unsigned char hold; /* in gbusclock */ unsigned char spw; /* in gbusclock */ - struct nand_hw_control hw_control; + struct nand_controller controller; }; static struct platform_device *mtd_to_platdev(struct mtd_info *mtd) @@ -254,23 +254,25 @@ static void txx9ndfmc_initialize(struct platform_device *dev) #define TXX9NDFMC_NS_TO_CYC(gbusclk, ns) \ DIV_ROUND_UP((ns) * DIV_ROUND_UP(gbusclk, 1000), 1000000) -static int txx9ndfmc_nand_scan(struct mtd_info *mtd) +static int txx9ndfmc_attach_chip(struct nand_chip *chip) { - struct nand_chip *chip = mtd_to_nand(mtd); - int ret; - - ret = nand_scan_ident(mtd, 1, NULL); - if (!ret) { - if (mtd->writesize >= 512) { - /* Hardware ECC 6 byte ECC per 512 Byte data */ - chip->ecc.size = 512; - chip->ecc.bytes = 6; - } - ret = nand_scan_tail(mtd); + struct mtd_info *mtd = nand_to_mtd(chip); + + if (mtd->writesize >= 512) { + chip->ecc.size = 512; + chip->ecc.bytes = 6; + } else { + chip->ecc.size = 256; + chip->ecc.bytes = 3; } - return ret; + + return 0; } +static const struct nand_controller_ops txx9ndfmc_controller_ops = { + .attach_chip = txx9ndfmc_attach_chip, +}; + static int __init txx9ndfmc_probe(struct platform_device *dev) { struct txx9ndfmc_platform_data *plat = dev_get_platdata(&dev->dev); @@ -303,7 +305,8 @@ static int __init txx9ndfmc_probe(struct platform_device *dev) dev_info(&dev->dev, "CLK:%ldMHz HOLD:%d SPW:%d\n", (gbusclk + 500000) / 1000000, hold, spw); - nand_hw_control_init(&drvdata->hw_control); + nand_controller_init(&drvdata->controller); + drvdata->controller.ops = &txx9ndfmc_controller_ops; platform_set_drvdata(dev, drvdata); txx9ndfmc_initialize(dev); @@ -332,12 +335,9 @@ static int __init txx9ndfmc_probe(struct platform_device *dev) chip->ecc.correct = txx9ndfmc_correct_data; chip->ecc.hwctl = txx9ndfmc_enable_hwecc; chip->ecc.mode = NAND_ECC_HW; - /* txx9ndfmc_nand_scan will overwrite ecc.size and ecc.bytes */ - chip->ecc.size = 256; - chip->ecc.bytes = 3; chip->ecc.strength = 1; chip->chip_delay = 100; - chip->controller = &drvdata->hw_control; + chip->controller = &drvdata->controller; nand_set_controller_data(chip, txx9_priv); txx9_priv->dev = dev; @@ -359,14 +359,14 @@ static int __init txx9ndfmc_probe(struct platform_device *dev) if (plat->wide_mask & (1 << i)) chip->options |= NAND_BUSWIDTH_16; - if (txx9ndfmc_nand_scan(mtd)) { + if (nand_scan(mtd, 1)) { kfree(txx9_priv->mtdname); kfree(txx9_priv); continue; } mtd->name = txx9_priv->mtdname; - mtd_device_parse_register(mtd, NULL, NULL, NULL, 0); + mtd_device_register(mtd, NULL, 0); drvdata->mtds[i] = mtd; } diff --git a/drivers/mtd/nand/raw/vf610_nfc.c b/drivers/mtd/nand/raw/vf610_nfc.c index d5a22fc96878..6f6dcbf9095b 100644 --- a/drivers/mtd/nand/raw/vf610_nfc.c +++ b/drivers/mtd/nand/raw/vf610_nfc.c @@ -747,6 +747,69 @@ static void vf610_nfc_init_controller(struct vf610_nfc *nfc) } } +static int vf610_nfc_attach_chip(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + + vf610_nfc_init_controller(nfc); + + /* Bad block options. */ + if (chip->bbt_options & NAND_BBT_USE_FLASH) + chip->bbt_options |= NAND_BBT_NO_OOB; + + /* Single buffer only, max 256 OOB minus ECC status */ + if (mtd->writesize + mtd->oobsize > PAGE_2K + OOB_MAX - 8) { + dev_err(nfc->dev, "Unsupported flash page size\n"); + return -ENXIO; + } + + if (chip->ecc.mode != NAND_ECC_HW) + return 0; + + if (mtd->writesize != PAGE_2K && mtd->oobsize < 64) { + dev_err(nfc->dev, "Unsupported flash with hwecc\n"); + return -ENXIO; + } + + if (chip->ecc.size != mtd->writesize) { + dev_err(nfc->dev, "Step size needs to be page size\n"); + return -ENXIO; + } + + /* Only 64 byte ECC layouts known */ + if (mtd->oobsize > 64) + mtd->oobsize = 64; + + /* Use default large page ECC layout defined in NAND core */ + mtd_set_ooblayout(mtd, &nand_ooblayout_lp_ops); + if (chip->ecc.strength == 32) { + nfc->ecc_mode = ECC_60_BYTE; + chip->ecc.bytes = 60; + } else if (chip->ecc.strength == 24) { + nfc->ecc_mode = ECC_45_BYTE; + chip->ecc.bytes = 45; + } else { + dev_err(nfc->dev, "Unsupported ECC strength\n"); + return -ENXIO; + } + + chip->ecc.read_page = vf610_nfc_read_page; + chip->ecc.write_page = vf610_nfc_write_page; + chip->ecc.read_page_raw = vf610_nfc_read_page_raw; + chip->ecc.write_page_raw = vf610_nfc_write_page_raw; + chip->ecc.read_oob = vf610_nfc_read_oob; + chip->ecc.write_oob = vf610_nfc_write_oob; + + chip->ecc.size = PAGE_2K; + + return 0; +} + +static const struct nand_controller_ops vf610_nfc_controller_ops = { + .attach_chip = vf610_nfc_attach_chip, +}; + static int vf610_nfc_probe(struct platform_device *pdev) { struct vf610_nfc *nfc; @@ -827,67 +890,9 @@ static int vf610_nfc_probe(struct platform_device *pdev) vf610_nfc_preinit_controller(nfc); - /* first scan to find the device and get the page size */ - err = nand_scan_ident(mtd, 1, NULL); - if (err) - goto err_disable_clk; - - vf610_nfc_init_controller(nfc); - - /* Bad block options. */ - if (chip->bbt_options & NAND_BBT_USE_FLASH) - chip->bbt_options |= NAND_BBT_NO_OOB; - - /* Single buffer only, max 256 OOB minus ECC status */ - if (mtd->writesize + mtd->oobsize > PAGE_2K + OOB_MAX - 8) { - dev_err(nfc->dev, "Unsupported flash page size\n"); - err = -ENXIO; - goto err_disable_clk; - } - - if (chip->ecc.mode == NAND_ECC_HW) { - if (mtd->writesize != PAGE_2K && mtd->oobsize < 64) { - dev_err(nfc->dev, "Unsupported flash with hwecc\n"); - err = -ENXIO; - goto err_disable_clk; - } - - if (chip->ecc.size != mtd->writesize) { - dev_err(nfc->dev, "Step size needs to be page size\n"); - err = -ENXIO; - goto err_disable_clk; - } - - /* Only 64 byte ECC layouts known */ - if (mtd->oobsize > 64) - mtd->oobsize = 64; - - /* Use default large page ECC layout defined in NAND core */ - mtd_set_ooblayout(mtd, &nand_ooblayout_lp_ops); - if (chip->ecc.strength == 32) { - nfc->ecc_mode = ECC_60_BYTE; - chip->ecc.bytes = 60; - } else if (chip->ecc.strength == 24) { - nfc->ecc_mode = ECC_45_BYTE; - chip->ecc.bytes = 45; - } else { - dev_err(nfc->dev, "Unsupported ECC strength\n"); - err = -ENXIO; - goto err_disable_clk; - } - - chip->ecc.read_page = vf610_nfc_read_page; - chip->ecc.write_page = vf610_nfc_write_page; - chip->ecc.read_page_raw = vf610_nfc_read_page_raw; - chip->ecc.write_page_raw = vf610_nfc_write_page_raw; - chip->ecc.read_oob = vf610_nfc_read_oob; - chip->ecc.write_oob = vf610_nfc_write_oob; - - chip->ecc.size = PAGE_2K; - } - - /* second phase scan */ - err = nand_scan_tail(mtd); + /* Scan the NAND chip */ + chip->dummy_controller.ops = &vf610_nfc_controller_ops; + err = nand_scan(mtd, 1); if (err) goto err_disable_clk; diff --git a/drivers/mtd/nand/spi/Kconfig b/drivers/mtd/nand/spi/Kconfig new file mode 100644 index 000000000000..7c37d2929b68 --- /dev/null +++ b/drivers/mtd/nand/spi/Kconfig @@ -0,0 +1,7 @@ +menuconfig MTD_SPI_NAND + tristate "SPI NAND device Support" + select MTD_NAND_CORE + depends on SPI_MASTER + select SPI_MEM + help + This is the framework for the SPI NAND device drivers. diff --git a/drivers/mtd/nand/spi/Makefile b/drivers/mtd/nand/spi/Makefile new file mode 100644 index 000000000000..b74e074b363a --- /dev/null +++ b/drivers/mtd/nand/spi/Makefile @@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0 +spinand-objs := core.o macronix.o micron.o winbond.o +obj-$(CONFIG_MTD_SPI_NAND) += spinand.o diff --git a/drivers/mtd/nand/spi/core.c b/drivers/mtd/nand/spi/core.c new file mode 100644 index 000000000000..30f83649c481 --- /dev/null +++ b/drivers/mtd/nand/spi/core.c @@ -0,0 +1,1155 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016-2017 Micron Technology, Inc. + * + * Authors: + * Peter Pan <peterpandong@micron.com> + * Boris Brezillon <boris.brezillon@bootlin.com> + */ + +#define pr_fmt(fmt) "spi-nand: " fmt + +#include <linux/device.h> +#include <linux/jiffies.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/mtd/spinand.h> +#include <linux/of.h> +#include <linux/slab.h> +#include <linux/spi/spi.h> +#include <linux/spi/spi-mem.h> + +static void spinand_cache_op_adjust_colum(struct spinand_device *spinand, + const struct nand_page_io_req *req, + u16 *column) +{ + struct nand_device *nand = spinand_to_nand(spinand); + unsigned int shift; + + if (nand->memorg.planes_per_lun < 2) + return; + + /* The plane number is passed in MSB just above the column address */ + shift = fls(nand->memorg.pagesize); + *column |= req->pos.plane << shift; +} + +static int spinand_read_reg_op(struct spinand_device *spinand, u8 reg, u8 *val) +{ + struct spi_mem_op op = SPINAND_GET_FEATURE_OP(reg, + spinand->scratchbuf); + int ret; + + ret = spi_mem_exec_op(spinand->spimem, &op); + if (ret) + return ret; + + *val = *spinand->scratchbuf; + return 0; +} + +static int spinand_write_reg_op(struct spinand_device *spinand, u8 reg, u8 val) +{ + struct spi_mem_op op = SPINAND_SET_FEATURE_OP(reg, + spinand->scratchbuf); + + *spinand->scratchbuf = val; + return spi_mem_exec_op(spinand->spimem, &op); +} + +static int spinand_read_status(struct spinand_device *spinand, u8 *status) +{ + return spinand_read_reg_op(spinand, REG_STATUS, status); +} + +static int spinand_get_cfg(struct spinand_device *spinand, u8 *cfg) +{ + struct nand_device *nand = spinand_to_nand(spinand); + + if (WARN_ON(spinand->cur_target < 0 || + spinand->cur_target >= nand->memorg.ntargets)) + return -EINVAL; + + *cfg = spinand->cfg_cache[spinand->cur_target]; + return 0; +} + +static int spinand_set_cfg(struct spinand_device *spinand, u8 cfg) +{ + struct nand_device *nand = spinand_to_nand(spinand); + int ret; + + if (WARN_ON(spinand->cur_target < 0 || + spinand->cur_target >= nand->memorg.ntargets)) + return -EINVAL; + + if (spinand->cfg_cache[spinand->cur_target] == cfg) + return 0; + + ret = spinand_write_reg_op(spinand, REG_CFG, cfg); + if (ret) + return ret; + + spinand->cfg_cache[spinand->cur_target] = cfg; + return 0; +} + +/** + * spinand_upd_cfg() - Update the configuration register + * @spinand: the spinand device + * @mask: the mask encoding the bits to update in the config reg + * @val: the new value to apply + * + * Update the configuration register. + * + * Return: 0 on success, a negative error code otherwise. + */ +int spinand_upd_cfg(struct spinand_device *spinand, u8 mask, u8 val) +{ + int ret; + u8 cfg; + + ret = spinand_get_cfg(spinand, &cfg); + if (ret) + return ret; + + cfg &= ~mask; + cfg |= val; + + return spinand_set_cfg(spinand, cfg); +} + +/** + * spinand_select_target() - Select a specific NAND target/die + * @spinand: the spinand device + * @target: the target/die to select + * + * Select a new target/die. If chip only has one die, this function is a NOOP. + * + * Return: 0 on success, a negative error code otherwise. + */ +int spinand_select_target(struct spinand_device *spinand, unsigned int target) +{ + struct nand_device *nand = spinand_to_nand(spinand); + int ret; + + if (WARN_ON(target >= nand->memorg.ntargets)) + return -EINVAL; + + if (spinand->cur_target == target) + return 0; + + if (nand->memorg.ntargets == 1) { + spinand->cur_target = target; + return 0; + } + + ret = spinand->select_target(spinand, target); + if (ret) + return ret; + + spinand->cur_target = target; + return 0; +} + +static int spinand_init_cfg_cache(struct spinand_device *spinand) +{ + struct nand_device *nand = spinand_to_nand(spinand); + struct device *dev = &spinand->spimem->spi->dev; + unsigned int target; + int ret; + + spinand->cfg_cache = devm_kcalloc(dev, + nand->memorg.ntargets, + sizeof(*spinand->cfg_cache), + GFP_KERNEL); + if (!spinand->cfg_cache) + return -ENOMEM; + + for (target = 0; target < nand->memorg.ntargets; target++) { + ret = spinand_select_target(spinand, target); + if (ret) + return ret; + + /* + * We use spinand_read_reg_op() instead of spinand_get_cfg() + * here to bypass the config cache. + */ + ret = spinand_read_reg_op(spinand, REG_CFG, + &spinand->cfg_cache[target]); + if (ret) + return ret; + } + + return 0; +} + +static int spinand_init_quad_enable(struct spinand_device *spinand) +{ + bool enable = false; + + if (!(spinand->flags & SPINAND_HAS_QE_BIT)) + return 0; + + if (spinand->op_templates.read_cache->data.buswidth == 4 || + spinand->op_templates.write_cache->data.buswidth == 4 || + spinand->op_templates.update_cache->data.buswidth == 4) + enable = true; + + return spinand_upd_cfg(spinand, CFG_QUAD_ENABLE, + enable ? CFG_QUAD_ENABLE : 0); +} + +static int spinand_ecc_enable(struct spinand_device *spinand, + bool enable) +{ + return spinand_upd_cfg(spinand, CFG_ECC_ENABLE, + enable ? CFG_ECC_ENABLE : 0); +} + +static int spinand_write_enable_op(struct spinand_device *spinand) +{ + struct spi_mem_op op = SPINAND_WR_EN_DIS_OP(true); + + return spi_mem_exec_op(spinand->spimem, &op); +} + +static int spinand_load_page_op(struct spinand_device *spinand, + const struct nand_page_io_req *req) +{ + struct nand_device *nand = spinand_to_nand(spinand); + unsigned int row = nanddev_pos_to_row(nand, &req->pos); + struct spi_mem_op op = SPINAND_PAGE_READ_OP(row); + + return spi_mem_exec_op(spinand->spimem, &op); +} + +static int spinand_read_from_cache_op(struct spinand_device *spinand, + const struct nand_page_io_req *req) +{ + struct spi_mem_op op = *spinand->op_templates.read_cache; + struct nand_device *nand = spinand_to_nand(spinand); + struct mtd_info *mtd = nanddev_to_mtd(nand); + struct nand_page_io_req adjreq = *req; + unsigned int nbytes = 0; + void *buf = NULL; + u16 column = 0; + int ret; + + if (req->datalen) { + adjreq.datalen = nanddev_page_size(nand); + adjreq.dataoffs = 0; + adjreq.databuf.in = spinand->databuf; + buf = spinand->databuf; + nbytes = adjreq.datalen; + } + + if (req->ooblen) { + adjreq.ooblen = nanddev_per_page_oobsize(nand); + adjreq.ooboffs = 0; + adjreq.oobbuf.in = spinand->oobbuf; + nbytes += nanddev_per_page_oobsize(nand); + if (!buf) { + buf = spinand->oobbuf; + column = nanddev_page_size(nand); + } + } + + spinand_cache_op_adjust_colum(spinand, &adjreq, &column); + op.addr.val = column; + + /* + * Some controllers are limited in term of max RX data size. In this + * case, just repeat the READ_CACHE operation after updating the + * column. + */ + while (nbytes) { + op.data.buf.in = buf; + op.data.nbytes = nbytes; + ret = spi_mem_adjust_op_size(spinand->spimem, &op); + if (ret) + return ret; + + ret = spi_mem_exec_op(spinand->spimem, &op); + if (ret) + return ret; + + buf += op.data.nbytes; + nbytes -= op.data.nbytes; + op.addr.val += op.data.nbytes; + } + + if (req->datalen) + memcpy(req->databuf.in, spinand->databuf + req->dataoffs, + req->datalen); + + if (req->ooblen) { + if (req->mode == MTD_OPS_AUTO_OOB) + mtd_ooblayout_get_databytes(mtd, req->oobbuf.in, + spinand->oobbuf, + req->ooboffs, + req->ooblen); + else + memcpy(req->oobbuf.in, spinand->oobbuf + req->ooboffs, + req->ooblen); + } + + return 0; +} + +static int spinand_write_to_cache_op(struct spinand_device *spinand, + const struct nand_page_io_req *req) +{ + struct spi_mem_op op = *spinand->op_templates.write_cache; + struct nand_device *nand = spinand_to_nand(spinand); + struct mtd_info *mtd = nanddev_to_mtd(nand); + struct nand_page_io_req adjreq = *req; + unsigned int nbytes = 0; + void *buf = NULL; + u16 column = 0; + int ret; + + memset(spinand->databuf, 0xff, + nanddev_page_size(nand) + + nanddev_per_page_oobsize(nand)); + + if (req->datalen) { + memcpy(spinand->databuf + req->dataoffs, req->databuf.out, + req->datalen); + adjreq.dataoffs = 0; + adjreq.datalen = nanddev_page_size(nand); + adjreq.databuf.out = spinand->databuf; + nbytes = adjreq.datalen; + buf = spinand->databuf; + } + + if (req->ooblen) { + if (req->mode == MTD_OPS_AUTO_OOB) + mtd_ooblayout_set_databytes(mtd, req->oobbuf.out, + spinand->oobbuf, + req->ooboffs, + req->ooblen); + else + memcpy(spinand->oobbuf + req->ooboffs, req->oobbuf.out, + req->ooblen); + + adjreq.ooblen = nanddev_per_page_oobsize(nand); + adjreq.ooboffs = 0; + nbytes += nanddev_per_page_oobsize(nand); + if (!buf) { + buf = spinand->oobbuf; + column = nanddev_page_size(nand); + } + } + + spinand_cache_op_adjust_colum(spinand, &adjreq, &column); + + op = *spinand->op_templates.write_cache; + op.addr.val = column; + + /* + * Some controllers are limited in term of max TX data size. In this + * case, split the operation into one LOAD CACHE and one or more + * LOAD RANDOM CACHE. + */ + while (nbytes) { + op.data.buf.out = buf; + op.data.nbytes = nbytes; + + ret = spi_mem_adjust_op_size(spinand->spimem, &op); + if (ret) + return ret; + + ret = spi_mem_exec_op(spinand->spimem, &op); + if (ret) + return ret; + + buf += op.data.nbytes; + nbytes -= op.data.nbytes; + op.addr.val += op.data.nbytes; + + /* + * We need to use the RANDOM LOAD CACHE operation if there's + * more than one iteration, because the LOAD operation resets + * the cache to 0xff. + */ + if (nbytes) { + column = op.addr.val; + op = *spinand->op_templates.update_cache; + op.addr.val = column; + } + } + + return 0; +} + +static int spinand_program_op(struct spinand_device *spinand, + const struct nand_page_io_req *req) +{ + struct nand_device *nand = spinand_to_nand(spinand); + unsigned int row = nanddev_pos_to_row(nand, &req->pos); + struct spi_mem_op op = SPINAND_PROG_EXEC_OP(row); + + return spi_mem_exec_op(spinand->spimem, &op); +} + +static int spinand_erase_op(struct spinand_device *spinand, + const struct nand_pos *pos) +{ + struct nand_device *nand = spinand_to_nand(spinand); + unsigned int row = nanddev_pos_to_row(nand, pos); + struct spi_mem_op op = SPINAND_BLK_ERASE_OP(row); + + return spi_mem_exec_op(spinand->spimem, &op); +} + +static int spinand_wait(struct spinand_device *spinand, u8 *s) +{ + unsigned long timeo = jiffies + msecs_to_jiffies(400); + u8 status; + int ret; + + do { + ret = spinand_read_status(spinand, &status); + if (ret) + return ret; + + if (!(status & STATUS_BUSY)) + goto out; + } while (time_before(jiffies, timeo)); + + /* + * Extra read, just in case the STATUS_READY bit has changed + * since our last check + */ + ret = spinand_read_status(spinand, &status); + if (ret) + return ret; + +out: + if (s) + *s = status; + + return status & STATUS_BUSY ? -ETIMEDOUT : 0; +} + +static int spinand_read_id_op(struct spinand_device *spinand, u8 *buf) +{ + struct spi_mem_op op = SPINAND_READID_OP(0, spinand->scratchbuf, + SPINAND_MAX_ID_LEN); + int ret; + + ret = spi_mem_exec_op(spinand->spimem, &op); + if (!ret) + memcpy(buf, spinand->scratchbuf, SPINAND_MAX_ID_LEN); + + return ret; +} + +static int spinand_reset_op(struct spinand_device *spinand) +{ + struct spi_mem_op op = SPINAND_RESET_OP; + int ret; + + ret = spi_mem_exec_op(spinand->spimem, &op); + if (ret) + return ret; + + return spinand_wait(spinand, NULL); +} + +static int spinand_lock_block(struct spinand_device *spinand, u8 lock) +{ + return spinand_write_reg_op(spinand, REG_BLOCK_LOCK, lock); +} + +static int spinand_check_ecc_status(struct spinand_device *spinand, u8 status) +{ + struct nand_device *nand = spinand_to_nand(spinand); + + if (spinand->eccinfo.get_status) + return spinand->eccinfo.get_status(spinand, status); + + switch (status & STATUS_ECC_MASK) { + case STATUS_ECC_NO_BITFLIPS: + return 0; + + case STATUS_ECC_HAS_BITFLIPS: + /* + * We have no way to know exactly how many bitflips have been + * fixed, so let's return the maximum possible value so that + * wear-leveling layers move the data immediately. + */ + return nand->eccreq.strength; + + case STATUS_ECC_UNCOR_ERROR: + return -EBADMSG; + + default: + break; + } + + return -EINVAL; +} + +static int spinand_read_page(struct spinand_device *spinand, + const struct nand_page_io_req *req, + bool ecc_enabled) +{ + u8 status; + int ret; + + ret = spinand_load_page_op(spinand, req); + if (ret) + return ret; + + ret = spinand_wait(spinand, &status); + if (ret < 0) + return ret; + + ret = spinand_read_from_cache_op(spinand, req); + if (ret) + return ret; + + if (!ecc_enabled) + return 0; + + return spinand_check_ecc_status(spinand, status); +} + +static int spinand_write_page(struct spinand_device *spinand, + const struct nand_page_io_req *req) +{ + u8 status; + int ret; + + ret = spinand_write_enable_op(spinand); + if (ret) + return ret; + + ret = spinand_write_to_cache_op(spinand, req); + if (ret) + return ret; + + ret = spinand_program_op(spinand, req); + if (ret) + return ret; + + ret = spinand_wait(spinand, &status); + if (!ret && (status & STATUS_PROG_FAILED)) + ret = -EIO; + + return ret; +} + +static int spinand_mtd_read(struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops) +{ + struct spinand_device *spinand = mtd_to_spinand(mtd); + struct nand_device *nand = mtd_to_nanddev(mtd); + unsigned int max_bitflips = 0; + struct nand_io_iter iter; + bool enable_ecc = false; + bool ecc_failed = false; + int ret = 0; + + if (ops->mode != MTD_OPS_RAW && spinand->eccinfo.ooblayout) + enable_ecc = true; + + mutex_lock(&spinand->lock); + + nanddev_io_for_each_page(nand, from, ops, &iter) { + ret = spinand_select_target(spinand, iter.req.pos.target); + if (ret) + break; + + ret = spinand_ecc_enable(spinand, enable_ecc); + if (ret) + break; + + ret = spinand_read_page(spinand, &iter.req, enable_ecc); + if (ret < 0 && ret != -EBADMSG) + break; + + if (ret == -EBADMSG) { + ecc_failed = true; + mtd->ecc_stats.failed++; + ret = 0; + } else { + mtd->ecc_stats.corrected += ret; + max_bitflips = max_t(unsigned int, max_bitflips, ret); + } + + ops->retlen += iter.req.datalen; + ops->oobretlen += iter.req.ooblen; + } + + mutex_unlock(&spinand->lock); + + if (ecc_failed && !ret) + ret = -EBADMSG; + + return ret ? ret : max_bitflips; +} + +static int spinand_mtd_write(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops) +{ + struct spinand_device *spinand = mtd_to_spinand(mtd); + struct nand_device *nand = mtd_to_nanddev(mtd); + struct nand_io_iter iter; + bool enable_ecc = false; + int ret = 0; + + if (ops->mode != MTD_OPS_RAW && mtd->ooblayout) + enable_ecc = true; + + mutex_lock(&spinand->lock); + + nanddev_io_for_each_page(nand, to, ops, &iter) { + ret = spinand_select_target(spinand, iter.req.pos.target); + if (ret) + break; + + ret = spinand_ecc_enable(spinand, enable_ecc); + if (ret) + break; + + ret = spinand_write_page(spinand, &iter.req); + if (ret) + break; + + ops->retlen += iter.req.datalen; + ops->oobretlen += iter.req.ooblen; + } + + mutex_unlock(&spinand->lock); + + return ret; +} + +static bool spinand_isbad(struct nand_device *nand, const struct nand_pos *pos) +{ + struct spinand_device *spinand = nand_to_spinand(nand); + struct nand_page_io_req req = { + .pos = *pos, + .ooblen = 2, + .ooboffs = 0, + .oobbuf.in = spinand->oobbuf, + .mode = MTD_OPS_RAW, + }; + + memset(spinand->oobbuf, 0, 2); + spinand_select_target(spinand, pos->target); + spinand_read_page(spinand, &req, false); + if (spinand->oobbuf[0] != 0xff || spinand->oobbuf[1] != 0xff) + return true; + + return false; +} + +static int spinand_mtd_block_isbad(struct mtd_info *mtd, loff_t offs) +{ + struct nand_device *nand = mtd_to_nanddev(mtd); + struct spinand_device *spinand = nand_to_spinand(nand); + struct nand_pos pos; + int ret; + + nanddev_offs_to_pos(nand, offs, &pos); + mutex_lock(&spinand->lock); + ret = nanddev_isbad(nand, &pos); + mutex_unlock(&spinand->lock); + + return ret; +} + +static int spinand_markbad(struct nand_device *nand, const struct nand_pos *pos) +{ + struct spinand_device *spinand = nand_to_spinand(nand); + struct nand_page_io_req req = { + .pos = *pos, + .ooboffs = 0, + .ooblen = 2, + .oobbuf.out = spinand->oobbuf, + }; + int ret; + + /* Erase block before marking it bad. */ + ret = spinand_select_target(spinand, pos->target); + if (ret) + return ret; + + ret = spinand_write_enable_op(spinand); + if (ret) + return ret; + + spinand_erase_op(spinand, pos); + + memset(spinand->oobbuf, 0, 2); + return spinand_write_page(spinand, &req); +} + +static int spinand_mtd_block_markbad(struct mtd_info *mtd, loff_t offs) +{ + struct nand_device *nand = mtd_to_nanddev(mtd); + struct spinand_device *spinand = nand_to_spinand(nand); + struct nand_pos pos; + int ret; + + nanddev_offs_to_pos(nand, offs, &pos); + mutex_lock(&spinand->lock); + ret = nanddev_markbad(nand, &pos); + mutex_unlock(&spinand->lock); + + return ret; +} + +static int spinand_erase(struct nand_device *nand, const struct nand_pos *pos) +{ + struct spinand_device *spinand = nand_to_spinand(nand); + u8 status; + int ret; + + ret = spinand_select_target(spinand, pos->target); + if (ret) + return ret; + + ret = spinand_write_enable_op(spinand); + if (ret) + return ret; + + ret = spinand_erase_op(spinand, pos); + if (ret) + return ret; + + ret = spinand_wait(spinand, &status); + if (!ret && (status & STATUS_ERASE_FAILED)) + ret = -EIO; + + return ret; +} + +static int spinand_mtd_erase(struct mtd_info *mtd, + struct erase_info *einfo) +{ + struct spinand_device *spinand = mtd_to_spinand(mtd); + int ret; + + mutex_lock(&spinand->lock); + ret = nanddev_mtd_erase(mtd, einfo); + mutex_unlock(&spinand->lock); + + return ret; +} + +static int spinand_mtd_block_isreserved(struct mtd_info *mtd, loff_t offs) +{ + struct spinand_device *spinand = mtd_to_spinand(mtd); + struct nand_device *nand = mtd_to_nanddev(mtd); + struct nand_pos pos; + int ret; + + nanddev_offs_to_pos(nand, offs, &pos); + mutex_lock(&spinand->lock); + ret = nanddev_isreserved(nand, &pos); + mutex_unlock(&spinand->lock); + + return ret; +} + +static const struct nand_ops spinand_ops = { + .erase = spinand_erase, + .markbad = spinand_markbad, + .isbad = spinand_isbad, +}; + +static const struct spinand_manufacturer *spinand_manufacturers[] = { + ¯onix_spinand_manufacturer, + µn_spinand_manufacturer, + &winbond_spinand_manufacturer, +}; + +static int spinand_manufacturer_detect(struct spinand_device *spinand) +{ + unsigned int i; + int ret; + + for (i = 0; i < ARRAY_SIZE(spinand_manufacturers); i++) { + ret = spinand_manufacturers[i]->ops->detect(spinand); + if (ret > 0) { + spinand->manufacturer = spinand_manufacturers[i]; + return 0; + } else if (ret < 0) { + return ret; + } + } + + return -ENOTSUPP; +} + +static int spinand_manufacturer_init(struct spinand_device *spinand) +{ + if (spinand->manufacturer->ops->init) + return spinand->manufacturer->ops->init(spinand); + + return 0; +} + +static void spinand_manufacturer_cleanup(struct spinand_device *spinand) +{ + /* Release manufacturer private data */ + if (spinand->manufacturer->ops->cleanup) + return spinand->manufacturer->ops->cleanup(spinand); +} + +static const struct spi_mem_op * +spinand_select_op_variant(struct spinand_device *spinand, + const struct spinand_op_variants *variants) +{ + struct nand_device *nand = spinand_to_nand(spinand); + unsigned int i; + + for (i = 0; i < variants->nops; i++) { + struct spi_mem_op op = variants->ops[i]; + unsigned int nbytes; + int ret; + + nbytes = nanddev_per_page_oobsize(nand) + + nanddev_page_size(nand); + + while (nbytes) { + op.data.nbytes = nbytes; + ret = spi_mem_adjust_op_size(spinand->spimem, &op); + if (ret) + break; + + if (!spi_mem_supports_op(spinand->spimem, &op)) + break; + + nbytes -= op.data.nbytes; + } + + if (!nbytes) + return &variants->ops[i]; + } + + return NULL; +} + +/** + * spinand_match_and_init() - Try to find a match between a device ID and an + * entry in a spinand_info table + * @spinand: SPI NAND object + * @table: SPI NAND device description table + * @table_size: size of the device description table + * + * Should be used by SPI NAND manufacturer drivers when they want to find a + * match between a device ID retrieved through the READ_ID command and an + * entry in the SPI NAND description table. If a match is found, the spinand + * object will be initialized with information provided by the matching + * spinand_info entry. + * + * Return: 0 on success, a negative error code otherwise. + */ +int spinand_match_and_init(struct spinand_device *spinand, + const struct spinand_info *table, + unsigned int table_size, u8 devid) +{ + struct nand_device *nand = spinand_to_nand(spinand); + unsigned int i; + + for (i = 0; i < table_size; i++) { + const struct spinand_info *info = &table[i]; + const struct spi_mem_op *op; + + if (devid != info->devid) + continue; + + nand->memorg = table[i].memorg; + nand->eccreq = table[i].eccreq; + spinand->eccinfo = table[i].eccinfo; + spinand->flags = table[i].flags; + spinand->select_target = table[i].select_target; + + op = spinand_select_op_variant(spinand, + info->op_variants.read_cache); + if (!op) + return -ENOTSUPP; + + spinand->op_templates.read_cache = op; + + op = spinand_select_op_variant(spinand, + info->op_variants.write_cache); + if (!op) + return -ENOTSUPP; + + spinand->op_templates.write_cache = op; + + op = spinand_select_op_variant(spinand, + info->op_variants.update_cache); + spinand->op_templates.update_cache = op; + + return 0; + } + + return -ENOTSUPP; +} + +static int spinand_detect(struct spinand_device *spinand) +{ + struct device *dev = &spinand->spimem->spi->dev; + struct nand_device *nand = spinand_to_nand(spinand); + int ret; + + ret = spinand_reset_op(spinand); + if (ret) + return ret; + + ret = spinand_read_id_op(spinand, spinand->id.data); + if (ret) + return ret; + + spinand->id.len = SPINAND_MAX_ID_LEN; + + ret = spinand_manufacturer_detect(spinand); + if (ret) { + dev_err(dev, "unknown raw ID %*phN\n", SPINAND_MAX_ID_LEN, + spinand->id.data); + return ret; + } + + if (nand->memorg.ntargets > 1 && !spinand->select_target) { + dev_err(dev, + "SPI NANDs with more than one die must implement ->select_target()\n"); + return -EINVAL; + } + + dev_info(&spinand->spimem->spi->dev, + "%s SPI NAND was found.\n", spinand->manufacturer->name); + dev_info(&spinand->spimem->spi->dev, + "%llu MiB, block size: %zu KiB, page size: %zu, OOB size: %u\n", + nanddev_size(nand) >> 20, nanddev_eraseblock_size(nand) >> 10, + nanddev_page_size(nand), nanddev_per_page_oobsize(nand)); + + return 0; +} + +static int spinand_noecc_ooblayout_ecc(struct mtd_info *mtd, int section, + struct mtd_oob_region *region) +{ + return -ERANGE; +} + +static int spinand_noecc_ooblayout_free(struct mtd_info *mtd, int section, + struct mtd_oob_region *region) +{ + if (section) + return -ERANGE; + + /* Reserve 2 bytes for the BBM. */ + region->offset = 2; + region->length = 62; + + return 0; +} + +static const struct mtd_ooblayout_ops spinand_noecc_ooblayout = { + .ecc = spinand_noecc_ooblayout_ecc, + .free = spinand_noecc_ooblayout_free, +}; + +static int spinand_init(struct spinand_device *spinand) +{ + struct device *dev = &spinand->spimem->spi->dev; + struct mtd_info *mtd = spinand_to_mtd(spinand); + struct nand_device *nand = mtd_to_nanddev(mtd); + int ret, i; + + /* + * We need a scratch buffer because the spi_mem interface requires that + * buf passed in spi_mem_op->data.buf be DMA-able. + */ + spinand->scratchbuf = kzalloc(SPINAND_MAX_ID_LEN, GFP_KERNEL); + if (!spinand->scratchbuf) + return -ENOMEM; + + ret = spinand_detect(spinand); + if (ret) + goto err_free_bufs; + + /* + * Use kzalloc() instead of devm_kzalloc() here, because some drivers + * may use this buffer for DMA access. + * Memory allocated by devm_ does not guarantee DMA-safe alignment. + */ + spinand->databuf = kzalloc(nanddev_page_size(nand) + + nanddev_per_page_oobsize(nand), + GFP_KERNEL); + if (!spinand->databuf) { + ret = -ENOMEM; + goto err_free_bufs; + } + + spinand->oobbuf = spinand->databuf + nanddev_page_size(nand); + + ret = spinand_init_cfg_cache(spinand); + if (ret) + goto err_free_bufs; + + ret = spinand_init_quad_enable(spinand); + if (ret) + goto err_free_bufs; + + ret = spinand_upd_cfg(spinand, CFG_OTP_ENABLE, 0); + if (ret) + goto err_free_bufs; + + ret = spinand_manufacturer_init(spinand); + if (ret) { + dev_err(dev, + "Failed to initialize the SPI NAND chip (err = %d)\n", + ret); + goto err_free_bufs; + } + + /* After power up, all blocks are locked, so unlock them here. */ + for (i = 0; i < nand->memorg.ntargets; i++) { + ret = spinand_select_target(spinand, i); + if (ret) + goto err_free_bufs; + + ret = spinand_lock_block(spinand, BL_ALL_UNLOCKED); + if (ret) + goto err_free_bufs; + } + + ret = nanddev_init(nand, &spinand_ops, THIS_MODULE); + if (ret) + goto err_manuf_cleanup; + + /* + * Right now, we don't support ECC, so let the whole oob + * area is available for user. + */ + mtd->_read_oob = spinand_mtd_read; + mtd->_write_oob = spinand_mtd_write; + mtd->_block_isbad = spinand_mtd_block_isbad; + mtd->_block_markbad = spinand_mtd_block_markbad; + mtd->_block_isreserved = spinand_mtd_block_isreserved; + mtd->_erase = spinand_mtd_erase; + + if (spinand->eccinfo.ooblayout) + mtd_set_ooblayout(mtd, spinand->eccinfo.ooblayout); + else + mtd_set_ooblayout(mtd, &spinand_noecc_ooblayout); + + ret = mtd_ooblayout_count_freebytes(mtd); + if (ret < 0) + goto err_cleanup_nanddev; + + mtd->oobavail = ret; + + return 0; + +err_cleanup_nanddev: + nanddev_cleanup(nand); + +err_manuf_cleanup: + spinand_manufacturer_cleanup(spinand); + +err_free_bufs: + kfree(spinand->databuf); + kfree(spinand->scratchbuf); + return ret; +} + +static void spinand_cleanup(struct spinand_device *spinand) +{ + struct nand_device *nand = spinand_to_nand(spinand); + + nanddev_cleanup(nand); + spinand_manufacturer_cleanup(spinand); + kfree(spinand->databuf); + kfree(spinand->scratchbuf); +} + +static int spinand_probe(struct spi_mem *mem) +{ + struct spinand_device *spinand; + struct mtd_info *mtd; + int ret; + + spinand = devm_kzalloc(&mem->spi->dev, sizeof(*spinand), + GFP_KERNEL); + if (!spinand) + return -ENOMEM; + + spinand->spimem = mem; + spi_mem_set_drvdata(mem, spinand); + spinand_set_of_node(spinand, mem->spi->dev.of_node); + mutex_init(&spinand->lock); + mtd = spinand_to_mtd(spinand); + mtd->dev.parent = &mem->spi->dev; + + ret = spinand_init(spinand); + if (ret) + return ret; + + ret = mtd_device_register(mtd, NULL, 0); + if (ret) + goto err_spinand_cleanup; + + return 0; + +err_spinand_cleanup: + spinand_cleanup(spinand); + + return ret; +} + +static int spinand_remove(struct spi_mem *mem) +{ + struct spinand_device *spinand; + struct mtd_info *mtd; + int ret; + + spinand = spi_mem_get_drvdata(mem); + mtd = spinand_to_mtd(spinand); + + ret = mtd_device_unregister(mtd); + if (ret) + return ret; + + spinand_cleanup(spinand); + + return 0; +} + +static const struct spi_device_id spinand_ids[] = { + { .name = "spi-nand" }, + { /* sentinel */ }, +}; + +#ifdef CONFIG_OF +static const struct of_device_id spinand_of_ids[] = { + { .compatible = "spi-nand" }, + { /* sentinel */ }, +}; +#endif + +static struct spi_mem_driver spinand_drv = { + .spidrv = { + .id_table = spinand_ids, + .driver = { + .name = "spi-nand", + .of_match_table = of_match_ptr(spinand_of_ids), + }, + }, + .probe = spinand_probe, + .remove = spinand_remove, +}; +module_spi_mem_driver(spinand_drv); + +MODULE_DESCRIPTION("SPI NAND framework"); +MODULE_AUTHOR("Peter Pan<peterpandong@micron.com>"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/mtd/nand/spi/macronix.c b/drivers/mtd/nand/spi/macronix.c new file mode 100644 index 000000000000..98f6b9c4b684 --- /dev/null +++ b/drivers/mtd/nand/spi/macronix.c @@ -0,0 +1,144 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018 Macronix + * + * Author: Boris Brezillon <boris.brezillon@bootlin.com> + */ + +#include <linux/device.h> +#include <linux/kernel.h> +#include <linux/mtd/spinand.h> + +#define SPINAND_MFR_MACRONIX 0xC2 + +static SPINAND_OP_VARIANTS(read_cache_variants, + SPINAND_PAGE_READ_FROM_CACHE_X4_OP(0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_X2_OP(0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_OP(true, 0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_OP(false, 0, 1, NULL, 0)); + +static SPINAND_OP_VARIANTS(write_cache_variants, + SPINAND_PROG_LOAD_X4(true, 0, NULL, 0), + SPINAND_PROG_LOAD(true, 0, NULL, 0)); + +static SPINAND_OP_VARIANTS(update_cache_variants, + SPINAND_PROG_LOAD_X4(false, 0, NULL, 0), + SPINAND_PROG_LOAD(false, 0, NULL, 0)); + +static int mx35lfxge4ab_ooblayout_ecc(struct mtd_info *mtd, int section, + struct mtd_oob_region *region) +{ + return -ERANGE; +} + +static int mx35lfxge4ab_ooblayout_free(struct mtd_info *mtd, int section, + struct mtd_oob_region *region) +{ + if (section) + return -ERANGE; + + region->offset = 2; + region->length = mtd->oobsize - 2; + + return 0; +} + +static const struct mtd_ooblayout_ops mx35lfxge4ab_ooblayout = { + .ecc = mx35lfxge4ab_ooblayout_ecc, + .free = mx35lfxge4ab_ooblayout_free, +}; + +static int mx35lf1ge4ab_get_eccsr(struct spinand_device *spinand, u8 *eccsr) +{ + struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(0x7c, 1), + SPI_MEM_OP_NO_ADDR, + SPI_MEM_OP_DUMMY(1, 1), + SPI_MEM_OP_DATA_IN(1, eccsr, 1)); + + return spi_mem_exec_op(spinand->spimem, &op); +} + +static int mx35lf1ge4ab_ecc_get_status(struct spinand_device *spinand, + u8 status) +{ + struct nand_device *nand = spinand_to_nand(spinand); + u8 eccsr; + + switch (status & STATUS_ECC_MASK) { + case STATUS_ECC_NO_BITFLIPS: + return 0; + + case STATUS_ECC_UNCOR_ERROR: + return -EBADMSG; + + case STATUS_ECC_HAS_BITFLIPS: + /* + * Let's try to retrieve the real maximum number of bitflips + * in order to avoid forcing the wear-leveling layer to move + * data around if it's not necessary. + */ + if (mx35lf1ge4ab_get_eccsr(spinand, &eccsr)) + return nand->eccreq.strength; + + if (WARN_ON(eccsr > nand->eccreq.strength || !eccsr)) + return nand->eccreq.strength; + + return eccsr; + + default: + break; + } + + return -EINVAL; +} + +static const struct spinand_info macronix_spinand_table[] = { + SPINAND_INFO("MX35LF1GE4AB", 0x12, + NAND_MEMORG(1, 2048, 64, 64, 1024, 1, 1, 1), + NAND_ECCREQ(4, 512), + SPINAND_INFO_OP_VARIANTS(&read_cache_variants, + &write_cache_variants, + &update_cache_variants), + SPINAND_HAS_QE_BIT, + SPINAND_ECCINFO(&mx35lfxge4ab_ooblayout, + mx35lf1ge4ab_ecc_get_status)), + SPINAND_INFO("MX35LF2GE4AB", 0x22, + NAND_MEMORG(1, 2048, 64, 64, 2048, 2, 1, 1), + NAND_ECCREQ(4, 512), + SPINAND_INFO_OP_VARIANTS(&read_cache_variants, + &write_cache_variants, + &update_cache_variants), + SPINAND_HAS_QE_BIT, + SPINAND_ECCINFO(&mx35lfxge4ab_ooblayout, NULL)), +}; + +static int macronix_spinand_detect(struct spinand_device *spinand) +{ + u8 *id = spinand->id.data; + int ret; + + /* + * Macronix SPI NAND read ID needs a dummy byte, so the first byte in + * raw_id is garbage. + */ + if (id[1] != SPINAND_MFR_MACRONIX) + return 0; + + ret = spinand_match_and_init(spinand, macronix_spinand_table, + ARRAY_SIZE(macronix_spinand_table), + id[2]); + if (ret) + return ret; + + return 1; +} + +static const struct spinand_manufacturer_ops macronix_spinand_manuf_ops = { + .detect = macronix_spinand_detect, +}; + +const struct spinand_manufacturer macronix_spinand_manufacturer = { + .id = SPINAND_MFR_MACRONIX, + .name = "Macronix", + .ops = ¯onix_spinand_manuf_ops, +}; diff --git a/drivers/mtd/nand/spi/micron.c b/drivers/mtd/nand/spi/micron.c new file mode 100644 index 000000000000..9c4381d6847b --- /dev/null +++ b/drivers/mtd/nand/spi/micron.c @@ -0,0 +1,133 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2016-2017 Micron Technology, Inc. + * + * Authors: + * Peter Pan <peterpandong@micron.com> + */ + +#include <linux/device.h> +#include <linux/kernel.h> +#include <linux/mtd/spinand.h> + +#define SPINAND_MFR_MICRON 0x2c + +#define MICRON_STATUS_ECC_MASK GENMASK(7, 4) +#define MICRON_STATUS_ECC_NO_BITFLIPS (0 << 4) +#define MICRON_STATUS_ECC_1TO3_BITFLIPS (1 << 4) +#define MICRON_STATUS_ECC_4TO6_BITFLIPS (3 << 4) +#define MICRON_STATUS_ECC_7TO8_BITFLIPS (5 << 4) + +static SPINAND_OP_VARIANTS(read_cache_variants, + SPINAND_PAGE_READ_FROM_CACHE_QUADIO_OP(0, 2, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_X4_OP(0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_DUALIO_OP(0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_X2_OP(0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_OP(true, 0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_OP(false, 0, 1, NULL, 0)); + +static SPINAND_OP_VARIANTS(write_cache_variants, + SPINAND_PROG_LOAD_X4(true, 0, NULL, 0), + SPINAND_PROG_LOAD(true, 0, NULL, 0)); + +static SPINAND_OP_VARIANTS(update_cache_variants, + SPINAND_PROG_LOAD_X4(false, 0, NULL, 0), + SPINAND_PROG_LOAD(false, 0, NULL, 0)); + +static int mt29f2g01abagd_ooblayout_ecc(struct mtd_info *mtd, int section, + struct mtd_oob_region *region) +{ + if (section) + return -ERANGE; + + region->offset = 64; + region->length = 64; + + return 0; +} + +static int mt29f2g01abagd_ooblayout_free(struct mtd_info *mtd, int section, + struct mtd_oob_region *region) +{ + if (section) + return -ERANGE; + + /* Reserve 2 bytes for the BBM. */ + region->offset = 2; + region->length = 62; + + return 0; +} + +static const struct mtd_ooblayout_ops mt29f2g01abagd_ooblayout = { + .ecc = mt29f2g01abagd_ooblayout_ecc, + .free = mt29f2g01abagd_ooblayout_free, +}; + +static int mt29f2g01abagd_ecc_get_status(struct spinand_device *spinand, + u8 status) +{ + switch (status & MICRON_STATUS_ECC_MASK) { + case STATUS_ECC_NO_BITFLIPS: + return 0; + + case STATUS_ECC_UNCOR_ERROR: + return -EBADMSG; + + case MICRON_STATUS_ECC_1TO3_BITFLIPS: + return 3; + + case MICRON_STATUS_ECC_4TO6_BITFLIPS: + return 6; + + case MICRON_STATUS_ECC_7TO8_BITFLIPS: + return 8; + + default: + break; + } + + return -EINVAL; +} + +static const struct spinand_info micron_spinand_table[] = { + SPINAND_INFO("MT29F2G01ABAGD", 0x24, + NAND_MEMORG(1, 2048, 128, 64, 2048, 2, 1, 1), + NAND_ECCREQ(8, 512), + SPINAND_INFO_OP_VARIANTS(&read_cache_variants, + &write_cache_variants, + &update_cache_variants), + 0, + SPINAND_ECCINFO(&mt29f2g01abagd_ooblayout, + mt29f2g01abagd_ecc_get_status)), +}; + +static int micron_spinand_detect(struct spinand_device *spinand) +{ + u8 *id = spinand->id.data; + int ret; + + /* + * Micron SPI NAND read ID need a dummy byte, + * so the first byte in raw_id is dummy. + */ + if (id[1] != SPINAND_MFR_MICRON) + return 0; + + ret = spinand_match_and_init(spinand, micron_spinand_table, + ARRAY_SIZE(micron_spinand_table), id[2]); + if (ret) + return ret; + + return 1; +} + +static const struct spinand_manufacturer_ops micron_spinand_manuf_ops = { + .detect = micron_spinand_detect, +}; + +const struct spinand_manufacturer micron_spinand_manufacturer = { + .id = SPINAND_MFR_MICRON, + .name = "Micron", + .ops = µn_spinand_manuf_ops, +}; diff --git a/drivers/mtd/nand/spi/winbond.c b/drivers/mtd/nand/spi/winbond.c new file mode 100644 index 000000000000..67baa1b32c00 --- /dev/null +++ b/drivers/mtd/nand/spi/winbond.c @@ -0,0 +1,141 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2017 exceet electronics GmbH + * + * Authors: + * Frieder Schrempf <frieder.schrempf@exceet.de> + * Boris Brezillon <boris.brezillon@bootlin.com> + */ + +#include <linux/device.h> +#include <linux/kernel.h> +#include <linux/mtd/spinand.h> + +#define SPINAND_MFR_WINBOND 0xEF + +#define WINBOND_CFG_BUF_READ BIT(3) + +static SPINAND_OP_VARIANTS(read_cache_variants, + SPINAND_PAGE_READ_FROM_CACHE_QUADIO_OP(0, 2, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_X4_OP(0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_DUALIO_OP(0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_X2_OP(0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_OP(true, 0, 1, NULL, 0), + SPINAND_PAGE_READ_FROM_CACHE_OP(false, 0, 1, NULL, 0)); + +static SPINAND_OP_VARIANTS(write_cache_variants, + SPINAND_PROG_LOAD_X4(true, 0, NULL, 0), + SPINAND_PROG_LOAD(true, 0, NULL, 0)); + +static SPINAND_OP_VARIANTS(update_cache_variants, + SPINAND_PROG_LOAD_X4(false, 0, NULL, 0), + SPINAND_PROG_LOAD(false, 0, NULL, 0)); + +static int w25m02gv_ooblayout_ecc(struct mtd_info *mtd, int section, + struct mtd_oob_region *region) +{ + if (section > 3) + return -ERANGE; + + region->offset = (16 * section) + 8; + region->length = 8; + + return 0; +} + +static int w25m02gv_ooblayout_free(struct mtd_info *mtd, int section, + struct mtd_oob_region *region) +{ + if (section > 3) + return -ERANGE; + + region->offset = (16 * section) + 2; + region->length = 6; + + return 0; +} + +static const struct mtd_ooblayout_ops w25m02gv_ooblayout = { + .ecc = w25m02gv_ooblayout_ecc, + .free = w25m02gv_ooblayout_free, +}; + +static int w25m02gv_select_target(struct spinand_device *spinand, + unsigned int target) +{ + struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(0xc2, 1), + SPI_MEM_OP_NO_ADDR, + SPI_MEM_OP_NO_DUMMY, + SPI_MEM_OP_DATA_OUT(1, + spinand->scratchbuf, + 1)); + + *spinand->scratchbuf = target; + return spi_mem_exec_op(spinand->spimem, &op); +} + +static const struct spinand_info winbond_spinand_table[] = { + SPINAND_INFO("W25M02GV", 0xAB, + NAND_MEMORG(1, 2048, 64, 64, 1024, 1, 1, 2), + NAND_ECCREQ(1, 512), + SPINAND_INFO_OP_VARIANTS(&read_cache_variants, + &write_cache_variants, + &update_cache_variants), + 0, + SPINAND_ECCINFO(&w25m02gv_ooblayout, NULL), + SPINAND_SELECT_TARGET(w25m02gv_select_target)), +}; + +/** + * winbond_spinand_detect - initialize device related part in spinand_device + * struct if it is a Winbond device. + * @spinand: SPI NAND device structure + */ +static int winbond_spinand_detect(struct spinand_device *spinand) +{ + u8 *id = spinand->id.data; + int ret; + + /* + * Winbond SPI NAND read ID need a dummy byte, + * so the first byte in raw_id is dummy. + */ + if (id[1] != SPINAND_MFR_WINBOND) + return 0; + + ret = spinand_match_and_init(spinand, winbond_spinand_table, + ARRAY_SIZE(winbond_spinand_table), id[2]); + if (ret) + return ret; + + return 1; +} + +static int winbond_spinand_init(struct spinand_device *spinand) +{ + struct nand_device *nand = spinand_to_nand(spinand); + unsigned int i; + + /* + * Make sure all dies are in buffer read mode and not continuous read + * mode. + */ + for (i = 0; i < nand->memorg.ntargets; i++) { + spinand_select_target(spinand, i); + spinand_upd_cfg(spinand, WINBOND_CFG_BUF_READ, + WINBOND_CFG_BUF_READ); + } + + return 0; +} + +static const struct spinand_manufacturer_ops winbond_spinand_manuf_ops = { + .detect = winbond_spinand_detect, + .init = winbond_spinand_init, +}; + +const struct spinand_manufacturer winbond_spinand_manufacturer = { + .id = SPINAND_MFR_WINBOND, + .name = "Winbond", + .ops = &winbond_spinand_manuf_ops, +}; diff --git a/drivers/mtd/nftlmount.c b/drivers/mtd/nftlmount.c index 27184e3874db..91b7fb326f9a 100644 --- a/drivers/mtd/nftlmount.c +++ b/drivers/mtd/nftlmount.c @@ -577,7 +577,7 @@ static int get_fold_mark(struct NFTLrecord *nftl, unsigned int block) int NFTL_mount(struct NFTLrecord *s) { int i; - unsigned int first_logical_block, logical_block, rep_block, nb_erases, erase_mark; + unsigned int first_logical_block, logical_block, rep_block, erase_mark; unsigned int block, first_block, is_first_block; int chain_length, do_format_chain; struct nftl_uci0 h0; @@ -621,7 +621,6 @@ int NFTL_mount(struct NFTLrecord *s) logical_block = le16_to_cpu ((h0.VirtUnitNum | h0.SpareVirtUnitNum)); rep_block = le16_to_cpu ((h0.ReplUnitNum | h0.SpareReplUnitNum)); - nb_erases = le32_to_cpu (h1.WearInfo); erase_mark = le16_to_cpu ((h1.EraseMark | h1.EraseMark1)); is_first_block = !(logical_block >> 15); diff --git a/drivers/mtd/parsers/parser_trx.c b/drivers/mtd/parsers/parser_trx.c index 17ac33599783..4a89a68622fe 100644 --- a/drivers/mtd/parsers/parser_trx.c +++ b/drivers/mtd/parsers/parser_trx.c @@ -116,9 +116,16 @@ static int parser_trx_parse(struct mtd_info *mtd, return i; }; +static const struct of_device_id mtd_parser_trx_of_match_table[] = { + { .compatible = "brcm,trx" }, + {}, +}; +MODULE_DEVICE_TABLE(of, mtd_parser_trx_of_match_table); + static struct mtd_part_parser mtd_parser_trx = { .parse_fn = parser_trx_parse, .name = "trx", + .of_match_table = mtd_parser_trx_of_match_table, }; module_mtd_part_parser(mtd_parser_trx); diff --git a/drivers/mtd/spi-nor/atmel-quadspi.c b/drivers/mtd/spi-nor/atmel-quadspi.c index 6c5708bacad8..820048726b4f 100644 --- a/drivers/mtd/spi-nor/atmel-quadspi.c +++ b/drivers/mtd/spi-nor/atmel-quadspi.c @@ -34,7 +34,7 @@ #include <linux/of.h> #include <linux/io.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> /* QSPI register offsets */ #define QSPI_CR 0x0000 /* Control Register */ @@ -737,6 +737,26 @@ static int atmel_qspi_remove(struct platform_device *pdev) return 0; } +static int __maybe_unused atmel_qspi_suspend(struct device *dev) +{ + struct atmel_qspi *aq = dev_get_drvdata(dev); + + clk_disable_unprepare(aq->clk); + + return 0; +} + +static int __maybe_unused atmel_qspi_resume(struct device *dev) +{ + struct atmel_qspi *aq = dev_get_drvdata(dev); + + clk_prepare_enable(aq->clk); + + return atmel_qspi_init(aq); +} + +static SIMPLE_DEV_PM_OPS(atmel_qspi_pm_ops, atmel_qspi_suspend, + atmel_qspi_resume); static const struct of_device_id atmel_qspi_dt_ids[] = { { .compatible = "atmel,sama5d2-qspi" }, @@ -749,6 +769,7 @@ static struct platform_driver atmel_qspi_driver = { .driver = { .name = "atmel_qspi", .of_match_table = atmel_qspi_dt_ids, + .pm = &atmel_qspi_pm_ops, }, .probe = atmel_qspi_probe, .remove = atmel_qspi_remove, diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/cadence-quadspi.c index d7e10b36a0b9..8e714fbfa521 100644 --- a/drivers/mtd/spi-nor/cadence-quadspi.c +++ b/drivers/mtd/spi-nor/cadence-quadspi.c @@ -525,15 +525,14 @@ static int cqspi_indirect_read_execute(struct spi_nor *nor, u8 *rxbuf, reg_base + CQSPI_REG_INDIRECTRD); while (remaining > 0) { - ret = wait_for_completion_timeout(&cqspi->transfer_complete, - msecs_to_jiffies - (CQSPI_READ_TIMEOUT_MS)); + if (!wait_for_completion_timeout(&cqspi->transfer_complete, + msecs_to_jiffies(CQSPI_READ_TIMEOUT_MS))) + ret = -ETIMEDOUT; bytes_to_read = cqspi_get_rd_sram_level(cqspi); - if (!ret && bytes_to_read == 0) { + if (ret && bytes_to_read == 0) { dev_err(nor->dev, "Indirect read timeout, no bytes\n"); - ret = -ETIMEDOUT; goto failrd; } @@ -649,10 +648,8 @@ static int cqspi_indirect_write_execute(struct spi_nor *nor, loff_t to_addr, iowrite32_rep(cqspi->ahb_base, txbuf, DIV_ROUND_UP(write_bytes, 4)); - ret = wait_for_completion_timeout(&cqspi->transfer_complete, - msecs_to_jiffies - (CQSPI_TIMEOUT_MS)); - if (!ret) { + if (!wait_for_completion_timeout(&cqspi->transfer_complete, + msecs_to_jiffies(CQSPI_TIMEOUT_MS))) { dev_err(nor->dev, "Indirect write timeout\n"); ret = -ETIMEDOUT; goto failwr; @@ -988,9 +985,8 @@ static int cqspi_direct_read_execute(struct spi_nor *nor, u_char *buf, } dma_async_issue_pending(cqspi->rx_chan); - ret = wait_for_completion_timeout(&cqspi->rx_dma_complete, - msecs_to_jiffies(len)); - if (ret <= 0) { + if (!wait_for_completion_timeout(&cqspi->rx_dma_complete, + msecs_to_jiffies(len))) { dmaengine_terminate_sync(cqspi->rx_chan); dev_err(nor->dev, "DMA wait_for_completion_timeout\n"); ret = -ETIMEDOUT; diff --git a/drivers/mtd/spi-nor/intel-spi.c b/drivers/mtd/spi-nor/intel-spi.c index d2cbfc27826e..af0a22019516 100644 --- a/drivers/mtd/spi-nor/intel-spi.c +++ b/drivers/mtd/spi-nor/intel-spi.c @@ -908,7 +908,7 @@ struct intel_spi *intel_spi_probe(struct device *dev, if (!ispi->writeable || !writeable) ispi->nor.mtd.flags &= ~MTD_WRITEABLE; - ret = mtd_device_parse_register(&ispi->nor.mtd, NULL, NULL, &part, 1); + ret = mtd_device_register(&ispi->nor.mtd, &part, 1); if (ret) return ERR_PTR(ret); diff --git a/drivers/mtd/spi-nor/nxp-spifi.c b/drivers/mtd/spi-nor/nxp-spifi.c index 15374216d4d9..0c9094ec5966 100644 --- a/drivers/mtd/spi-nor/nxp-spifi.c +++ b/drivers/mtd/spi-nor/nxp-spifi.c @@ -436,6 +436,7 @@ static int nxp_spifi_probe(struct platform_device *pdev) } ret = nxp_spifi_setup_flash(spifi, flash_np); + of_node_put(flash_np); if (ret) { dev_err(&pdev->dev, "unable to setup flash chip\n"); goto dis_clks; diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c index d9c368c44194..f028277fb1ce 100644 --- a/drivers/mtd/spi-nor/spi-nor.c +++ b/drivers/mtd/spi-nor/spi-nor.c @@ -2757,8 +2757,18 @@ static int spi_nor_init(struct spi_nor *nor) if ((nor->addr_width == 4) && (JEDEC_MFR(nor->info) != SNOR_MFR_SPANSION) && - !(nor->info->flags & SPI_NOR_4B_OPCODES)) + !(nor->info->flags & SPI_NOR_4B_OPCODES)) { + /* + * If the RESET# pin isn't hooked up properly, or the system + * otherwise doesn't perform a reset command in the boot + * sequence, it's impossible to 100% protect against unexpected + * reboots (e.g., crashes). Warn the user (or hopefully, system + * designer) that this is bad. + */ + WARN_ONCE(nor->flags & SNOR_F_BROKEN_RESET, + "enabling reset hack; may not recover from unexpected reboots\n"); set_4byte(nor, nor->info, 1); + } return 0; } @@ -2781,7 +2791,8 @@ void spi_nor_restore(struct spi_nor *nor) /* restore the addressing mode */ if ((nor->addr_width == 4) && (JEDEC_MFR(nor->info) != SNOR_MFR_SPANSION) && - !(nor->info->flags & SPI_NOR_4B_OPCODES)) + !(nor->info->flags & SPI_NOR_4B_OPCODES) && + (nor->flags & SNOR_F_BROKEN_RESET)) set_4byte(nor, nor->info, 0); } EXPORT_SYMBOL_GPL(spi_nor_restore); @@ -2911,6 +2922,9 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, params.hwcaps.mask |= SNOR_HWCAPS_READ_FAST; } + if (of_property_read_bool(np, "broken-flash-reset")) + nor->flags |= SNOR_F_BROKEN_RESET; + /* Some devices cannot do fast-read, no matter what DT tells us */ if (info->flags & SPI_NOR_NO_FR) params.hwcaps.mask &= ~SNOR_HWCAPS_READ_FAST; diff --git a/drivers/mtd/spi-nor/stm32-quadspi.c b/drivers/mtd/spi-nor/stm32-quadspi.c index 72553506a00b..13e9fc961d3b 100644 --- a/drivers/mtd/spi-nor/stm32-quadspi.c +++ b/drivers/mtd/spi-nor/stm32-quadspi.c @@ -355,7 +355,7 @@ static int stm32_qspi_read_reg(struct spi_nor *nor, struct device *dev = flash->qspi->dev; struct stm32_qspi_cmd cmd; - dev_dbg(dev, "read_reg: cmd:%#.2x buf:%p len:%#x\n", opcode, buf, len); + dev_dbg(dev, "read_reg: cmd:%#.2x buf:%pK len:%#x\n", opcode, buf, len); memset(&cmd, 0, sizeof(cmd)); cmd.opcode = opcode; @@ -376,7 +376,7 @@ static int stm32_qspi_write_reg(struct spi_nor *nor, u8 opcode, struct device *dev = flash->qspi->dev; struct stm32_qspi_cmd cmd; - dev_dbg(dev, "write_reg: cmd:%#.2x buf:%p len:%#x\n", opcode, buf, len); + dev_dbg(dev, "write_reg: cmd:%#.2x buf:%pK len:%#x\n", opcode, buf, len); memset(&cmd, 0, sizeof(cmd)); cmd.opcode = opcode; @@ -398,7 +398,7 @@ static ssize_t stm32_qspi_read(struct spi_nor *nor, loff_t from, size_t len, struct stm32_qspi_cmd cmd; int err; - dev_dbg(qspi->dev, "read(%#.2x): buf:%p from:%#.8x len:%#zx\n", + dev_dbg(qspi->dev, "read(%#.2x): buf:%pK from:%#.8x len:%#zx\n", nor->read_opcode, buf, (u32)from, len); memset(&cmd, 0, sizeof(cmd)); diff --git a/fs/jffs2/dir.c b/fs/jffs2/dir.c index b2944f9218f7..f20cff1194bb 100644 --- a/fs/jffs2/dir.c +++ b/fs/jffs2/dir.c @@ -201,7 +201,7 @@ static int jffs2_create(struct inode *dir_i, struct dentry *dentry, if (ret) goto fail; - dir_i->i_mtime = dir_i->i_ctime = timespec_to_timespec64(ITIME(je32_to_cpu(ri->ctime))); + dir_i->i_mtime = dir_i->i_ctime = ITIME(je32_to_cpu(ri->ctime)); jffs2_free_raw_inode(ri); @@ -227,14 +227,14 @@ static int jffs2_unlink(struct inode *dir_i, struct dentry *dentry) struct jffs2_inode_info *dir_f = JFFS2_INODE_INFO(dir_i); struct jffs2_inode_info *dead_f = JFFS2_INODE_INFO(d_inode(dentry)); int ret; - uint32_t now = get_seconds(); + uint32_t now = JFFS2_NOW(); ret = jffs2_do_unlink(c, dir_f, dentry->d_name.name, dentry->d_name.len, dead_f, now); if (dead_f->inocache) set_nlink(d_inode(dentry), dead_f->inocache->pino_nlink); if (!ret) - dir_i->i_mtime = dir_i->i_ctime = timespec_to_timespec64(ITIME(now)); + dir_i->i_mtime = dir_i->i_ctime = ITIME(now); return ret; } /***********************************************************************/ @@ -260,7 +260,7 @@ static int jffs2_link (struct dentry *old_dentry, struct inode *dir_i, struct de type = (d_inode(old_dentry)->i_mode & S_IFMT) >> 12; if (!type) type = DT_REG; - now = get_seconds(); + now = JFFS2_NOW(); ret = jffs2_do_link(c, dir_f, f->inocache->ino, type, dentry->d_name.name, dentry->d_name.len, now); if (!ret) { @@ -268,7 +268,7 @@ static int jffs2_link (struct dentry *old_dentry, struct inode *dir_i, struct de set_nlink(d_inode(old_dentry), ++f->inocache->pino_nlink); mutex_unlock(&f->sem); d_instantiate(dentry, d_inode(old_dentry)); - dir_i->i_mtime = dir_i->i_ctime = timespec_to_timespec64(ITIME(now)); + dir_i->i_mtime = dir_i->i_ctime = ITIME(now); ihold(d_inode(old_dentry)); } return ret; @@ -400,7 +400,7 @@ static int jffs2_symlink (struct inode *dir_i, struct dentry *dentry, const char rd->pino = cpu_to_je32(dir_i->i_ino); rd->version = cpu_to_je32(++dir_f->highest_version); rd->ino = cpu_to_je32(inode->i_ino); - rd->mctime = cpu_to_je32(get_seconds()); + rd->mctime = cpu_to_je32(JFFS2_NOW()); rd->nsize = namelen; rd->type = DT_LNK; rd->node_crc = cpu_to_je32(crc32(0, rd, sizeof(*rd)-8)); @@ -418,7 +418,7 @@ static int jffs2_symlink (struct inode *dir_i, struct dentry *dentry, const char goto fail; } - dir_i->i_mtime = dir_i->i_ctime = timespec_to_timespec64(ITIME(je32_to_cpu(rd->mctime))); + dir_i->i_mtime = dir_i->i_ctime = ITIME(je32_to_cpu(rd->mctime)); jffs2_free_raw_dirent(rd); @@ -543,7 +543,7 @@ static int jffs2_mkdir (struct inode *dir_i, struct dentry *dentry, umode_t mode rd->pino = cpu_to_je32(dir_i->i_ino); rd->version = cpu_to_je32(++dir_f->highest_version); rd->ino = cpu_to_je32(inode->i_ino); - rd->mctime = cpu_to_je32(get_seconds()); + rd->mctime = cpu_to_je32(JFFS2_NOW()); rd->nsize = namelen; rd->type = DT_DIR; rd->node_crc = cpu_to_je32(crc32(0, rd, sizeof(*rd)-8)); @@ -561,7 +561,7 @@ static int jffs2_mkdir (struct inode *dir_i, struct dentry *dentry, umode_t mode goto fail; } - dir_i->i_mtime = dir_i->i_ctime = timespec_to_timespec64(ITIME(je32_to_cpu(rd->mctime))); + dir_i->i_mtime = dir_i->i_ctime = ITIME(je32_to_cpu(rd->mctime)); inc_nlink(dir_i); jffs2_free_raw_dirent(rd); @@ -588,7 +588,7 @@ static int jffs2_rmdir (struct inode *dir_i, struct dentry *dentry) struct jffs2_inode_info *f = JFFS2_INODE_INFO(d_inode(dentry)); struct jffs2_full_dirent *fd; int ret; - uint32_t now = get_seconds(); + uint32_t now = JFFS2_NOW(); for (fd = f->dents ; fd; fd = fd->next) { if (fd->ino) @@ -598,7 +598,7 @@ static int jffs2_rmdir (struct inode *dir_i, struct dentry *dentry) ret = jffs2_do_unlink(c, dir_f, dentry->d_name.name, dentry->d_name.len, f, now); if (!ret) { - dir_i->i_mtime = dir_i->i_ctime = timespec_to_timespec64(ITIME(now)); + dir_i->i_mtime = dir_i->i_ctime = ITIME(now); clear_nlink(d_inode(dentry)); drop_nlink(dir_i); } @@ -712,7 +712,7 @@ static int jffs2_mknod (struct inode *dir_i, struct dentry *dentry, umode_t mode rd->pino = cpu_to_je32(dir_i->i_ino); rd->version = cpu_to_je32(++dir_f->highest_version); rd->ino = cpu_to_je32(inode->i_ino); - rd->mctime = cpu_to_je32(get_seconds()); + rd->mctime = cpu_to_je32(JFFS2_NOW()); rd->nsize = namelen; /* XXX: This is ugly. */ @@ -733,7 +733,7 @@ static int jffs2_mknod (struct inode *dir_i, struct dentry *dentry, umode_t mode goto fail; } - dir_i->i_mtime = dir_i->i_ctime = timespec_to_timespec64(ITIME(je32_to_cpu(rd->mctime))); + dir_i->i_mtime = dir_i->i_ctime = ITIME(je32_to_cpu(rd->mctime)); jffs2_free_raw_dirent(rd); @@ -797,7 +797,7 @@ static int jffs2_rename (struct inode *old_dir_i, struct dentry *old_dentry, type = (d_inode(old_dentry)->i_mode & S_IFMT) >> 12; if (!type) type = DT_REG; - now = get_seconds(); + now = JFFS2_NOW(); ret = jffs2_do_link(c, JFFS2_INODE_INFO(new_dir_i), d_inode(old_dentry)->i_ino, type, new_dentry->d_name.name, new_dentry->d_name.len, now); @@ -853,14 +853,14 @@ static int jffs2_rename (struct inode *old_dir_i, struct dentry *old_dentry, * caller won't do it on its own since we are returning an error. */ d_invalidate(new_dentry); - new_dir_i->i_mtime = new_dir_i->i_ctime = timespec_to_timespec64(ITIME(now)); + new_dir_i->i_mtime = new_dir_i->i_ctime = ITIME(now); return ret; } if (d_is_dir(old_dentry)) drop_nlink(old_dir_i); - new_dir_i->i_mtime = new_dir_i->i_ctime = old_dir_i->i_mtime = old_dir_i->i_ctime = timespec_to_timespec64(ITIME(now)); + new_dir_i->i_mtime = new_dir_i->i_ctime = old_dir_i->i_mtime = old_dir_i->i_ctime = ITIME(now); return 0; } diff --git a/fs/jffs2/file.c b/fs/jffs2/file.c index 481afd4c2e1a..7d8654a1472e 100644 --- a/fs/jffs2/file.c +++ b/fs/jffs2/file.c @@ -175,7 +175,7 @@ static int jffs2_write_begin(struct file *filp, struct address_space *mapping, ri.uid = cpu_to_je16(i_uid_read(inode)); ri.gid = cpu_to_je16(i_gid_read(inode)); ri.isize = cpu_to_je32(max((uint32_t)inode->i_size, pageofs)); - ri.atime = ri.ctime = ri.mtime = cpu_to_je32(get_seconds()); + ri.atime = ri.ctime = ri.mtime = cpu_to_je32(JFFS2_NOW()); ri.offset = cpu_to_je32(inode->i_size); ri.dsize = cpu_to_je32(pageofs - inode->i_size); ri.csize = cpu_to_je32(0); @@ -283,7 +283,7 @@ static int jffs2_write_end(struct file *filp, struct address_space *mapping, ri->uid = cpu_to_je16(i_uid_read(inode)); ri->gid = cpu_to_je16(i_gid_read(inode)); ri->isize = cpu_to_je32((uint32_t)inode->i_size); - ri->atime = ri->ctime = ri->mtime = cpu_to_je32(get_seconds()); + ri->atime = ri->ctime = ri->mtime = cpu_to_je32(JFFS2_NOW()); /* In 2.4, it was already kmapped by generic_file_write(). Doesn't hurt to do it again. The alternative is ifdefs, which are ugly. */ @@ -308,7 +308,7 @@ static int jffs2_write_end(struct file *filp, struct address_space *mapping, inode->i_size = pos + writtenlen; inode->i_blocks = (inode->i_size + 511) >> 9; - inode->i_ctime = inode->i_mtime = timespec_to_timespec64(ITIME(je32_to_cpu(ri->ctime))); + inode->i_ctime = inode->i_mtime = ITIME(je32_to_cpu(ri->ctime)); } } diff --git a/fs/jffs2/fs.c b/fs/jffs2/fs.c index 0ecfb8ea38cd..eab04eca95a3 100644 --- a/fs/jffs2/fs.c +++ b/fs/jffs2/fs.c @@ -146,9 +146,9 @@ int jffs2_do_setattr (struct inode *inode, struct iattr *iattr) return PTR_ERR(new_metadata); } /* It worked. Update the inode */ - inode->i_atime = timespec_to_timespec64(ITIME(je32_to_cpu(ri->atime))); - inode->i_ctime = timespec_to_timespec64(ITIME(je32_to_cpu(ri->ctime))); - inode->i_mtime = timespec_to_timespec64(ITIME(je32_to_cpu(ri->mtime))); + inode->i_atime = ITIME(je32_to_cpu(ri->atime)); + inode->i_ctime = ITIME(je32_to_cpu(ri->ctime)); + inode->i_mtime = ITIME(je32_to_cpu(ri->mtime)); inode->i_mode = jemode_to_cpu(ri->mode); i_uid_write(inode, je16_to_cpu(ri->uid)); i_gid_write(inode, je16_to_cpu(ri->gid)); @@ -280,9 +280,9 @@ struct inode *jffs2_iget(struct super_block *sb, unsigned long ino) i_uid_write(inode, je16_to_cpu(latest_node.uid)); i_gid_write(inode, je16_to_cpu(latest_node.gid)); inode->i_size = je32_to_cpu(latest_node.isize); - inode->i_atime = timespec_to_timespec64(ITIME(je32_to_cpu(latest_node.atime))); - inode->i_mtime = timespec_to_timespec64(ITIME(je32_to_cpu(latest_node.mtime))); - inode->i_ctime = timespec_to_timespec64(ITIME(je32_to_cpu(latest_node.ctime))); + inode->i_atime = ITIME(je32_to_cpu(latest_node.atime)); + inode->i_mtime = ITIME(je32_to_cpu(latest_node.mtime)); + inode->i_ctime = ITIME(je32_to_cpu(latest_node.ctime)); set_nlink(inode, f->inocache->pino_nlink); diff --git a/fs/jffs2/os-linux.h b/fs/jffs2/os-linux.h index c2fbec19c616..a2dbbb3f4c74 100644 --- a/fs/jffs2/os-linux.h +++ b/fs/jffs2/os-linux.h @@ -31,12 +31,13 @@ struct kvec; #define JFFS2_F_I_GID(f) (i_gid_read(OFNI_EDONI_2SFFJ(f))) #define JFFS2_F_I_RDEV(f) (OFNI_EDONI_2SFFJ(f)->i_rdev) -#define ITIME(sec) ((struct timespec){sec, 0}) -#define I_SEC(tv) ((tv).tv_sec) -#define JFFS2_F_I_CTIME(f) (OFNI_EDONI_2SFFJ(f)->i_ctime.tv_sec) -#define JFFS2_F_I_MTIME(f) (OFNI_EDONI_2SFFJ(f)->i_mtime.tv_sec) -#define JFFS2_F_I_ATIME(f) (OFNI_EDONI_2SFFJ(f)->i_atime.tv_sec) - +#define JFFS2_CLAMP_TIME(t) ((uint32_t)clamp_t(time64_t, (t), 0, U32_MAX)) +#define ITIME(sec) ((struct timespec64){sec, 0}) +#define JFFS2_NOW() JFFS2_CLAMP_TIME(ktime_get_real_seconds()) +#define I_SEC(tv) JFFS2_CLAMP_TIME((tv).tv_sec) +#define JFFS2_F_I_CTIME(f) I_SEC(OFNI_EDONI_2SFFJ(f)->i_ctime) +#define JFFS2_F_I_MTIME(f) I_SEC(OFNI_EDONI_2SFFJ(f)->i_mtime) +#define JFFS2_F_I_ATIME(f) I_SEC(OFNI_EDONI_2SFFJ(f)->i_atime) #define sleep_on_spinunlock(wq, s) \ do { \ DECLARE_WAITQUEUE(__wait, current); \ diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h index a86c4fa93115..cd0be91bdefa 100644 --- a/include/linux/mtd/mtd.h +++ b/include/linux/mtd/mtd.h @@ -67,9 +67,11 @@ struct mtd_erase_region_info { * @datbuf: data buffer - if NULL only oob data are read/written * @oobbuf: oob data buffer * - * Note, it is allowed to read more than one OOB area at one go, but not write. - * The interface assumes that the OOB write requests program only one page's - * OOB area. + * Note, some MTD drivers do not allow you to write more than one OOB area at + * one go. If you try to do that on such an MTD device, -EINVAL will be + * returned. If you want to make your implementation portable on all kind of MTD + * devices you should split the write request into several sub-requests when the + * request crosses a page boundary. */ struct mtd_oob_ops { unsigned int mode; diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h index 3e8ec3b8a39c..efb2345359bb 100644 --- a/include/linux/mtd/rawnand.h +++ b/include/linux/mtd/rawnand.h @@ -21,11 +21,10 @@ #include <linux/mtd/mtd.h> #include <linux/mtd/flashchip.h> #include <linux/mtd/bbm.h> +#include <linux/of.h> #include <linux/types.h> -struct mtd_info; struct nand_flash_dev; -struct device_node; /* Scan and identify a NAND device */ int nand_scan_with_ids(struct mtd_info *mtd, int max_chips, @@ -36,17 +35,6 @@ static inline int nand_scan(struct mtd_info *mtd, int max_chips) return nand_scan_with_ids(mtd, max_chips, NULL); } -/* - * Separate phases of nand_scan(), allowing board driver to intervene - * and override command or ECC setup according to flash type. - */ -int nand_scan_ident(struct mtd_info *mtd, int max_chips, - struct nand_flash_dev *table); -int nand_scan_tail(struct mtd_info *mtd); - -/* Unregister the MTD device and free resources held by the NAND device */ -void nand_release(struct mtd_info *mtd); - /* Internal helper for board drivers which need to override command function */ void nand_wait_ready(struct mtd_info *mtd); @@ -121,6 +109,7 @@ enum nand_ecc_algo { NAND_ECC_UNKNOWN, NAND_ECC_HAMMING, NAND_ECC_BCH, + NAND_ECC_RS, }; /* @@ -218,6 +207,12 @@ enum nand_ecc_algo { */ #define NAND_WAIT_TCCS 0x00200000 +/* + * Whether the NAND chip is a boot medium. Drivers might use this information + * to select ECC algorithms supported by the boot ROM or similar restrictions. + */ +#define NAND_IS_BOOT_MEDIUM 0x00400000 + /* Options set by nand scan */ /* Nand scan has allocated controller struct */ #define NAND_CONTROLLER_ALLOC 0x80000000 @@ -230,6 +225,17 @@ enum nand_ecc_algo { /* Keep gcc happy */ struct nand_chip; +/* ONFI version bits */ +#define ONFI_VERSION_1_0 BIT(1) +#define ONFI_VERSION_2_0 BIT(2) +#define ONFI_VERSION_2_1 BIT(3) +#define ONFI_VERSION_2_2 BIT(4) +#define ONFI_VERSION_2_3 BIT(5) +#define ONFI_VERSION_3_0 BIT(6) +#define ONFI_VERSION_3_1 BIT(7) +#define ONFI_VERSION_3_2 BIT(8) +#define ONFI_VERSION_4_0 BIT(9) + /* ONFI features */ #define ONFI_FEATURE_16_BIT_BUS (1 << 0) #define ONFI_FEATURE_EXT_PARAM_PAGE (1 << 7) @@ -470,13 +476,13 @@ struct onfi_params { */ struct nand_parameters { /* Generic parameters */ - char model[100]; + const char *model; bool supports_set_get_features; DECLARE_BITMAP(set_feature_list, ONFI_FEATURE_NUMBER); DECLARE_BITMAP(get_feature_list, ONFI_FEATURE_NUMBER); /* ONFI parameters */ - struct onfi_params onfi; + struct onfi_params *onfi; }; /* The maximum expected count of bytes in the NAND ID sequence */ @@ -493,20 +499,42 @@ struct nand_id { }; /** - * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices + * struct nand_controller_ops - Controller operations + * + * @attach_chip: this method is called after the NAND detection phase after + * flash ID and MTD fields such as erase size, page size and OOB + * size have been set up. ECC requirements are available if + * provided by the NAND chip or device tree. Typically used to + * choose the appropriate ECC configuration and allocate + * associated resources. + * This hook is optional. + * @detach_chip: free all resources allocated/claimed in + * nand_controller_ops->attach_chip(). + * This hook is optional. + */ +struct nand_controller_ops { + int (*attach_chip)(struct nand_chip *chip); + void (*detach_chip)(struct nand_chip *chip); +}; + +/** + * struct nand_controller - Structure used to describe a NAND controller + * * @lock: protection lock * @active: the mtd device which holds the controller currently * @wq: wait queue to sleep on if a NAND operation is in * progress used instead of the per chip wait queue * when a hw controller is available. + * @ops: NAND controller operations. */ -struct nand_hw_control { +struct nand_controller { spinlock_t lock; struct nand_chip *active; wait_queue_head_t wq; + const struct nand_controller_ops *ops; }; -static inline void nand_hw_control_init(struct nand_hw_control *nfc) +static inline void nand_controller_init(struct nand_controller *nfc) { nfc->active = NULL; spin_lock_init(&nfc->lock); @@ -778,11 +806,15 @@ nand_get_sdr_timings(const struct nand_data_interface *conf) * implementation) if any. * @cleanup: the ->init() function may have allocated resources, ->cleanup() * is here to let vendor specific code release those resources. + * @fixup_onfi_param_page: apply vendor specific fixups to the ONFI parameter + * page. This is called after the checksum is verified. */ struct nand_manufacturer_ops { void (*detect)(struct nand_chip *chip); int (*init)(struct nand_chip *chip); void (*cleanup)(struct nand_chip *chip); + void (*fixup_onfi_param_page)(struct nand_chip *chip, + struct nand_onfi_params *p); }; /** @@ -986,14 +1018,14 @@ struct nand_subop { unsigned int last_instr_end_off; }; -int nand_subop_get_addr_start_off(const struct nand_subop *subop, - unsigned int op_id); -int nand_subop_get_num_addr_cyc(const struct nand_subop *subop, - unsigned int op_id); -int nand_subop_get_data_start_off(const struct nand_subop *subop, - unsigned int op_id); -int nand_subop_get_data_len(const struct nand_subop *subop, - unsigned int op_id); +unsigned int nand_subop_get_addr_start_off(const struct nand_subop *subop, + unsigned int op_id); +unsigned int nand_subop_get_num_addr_cyc(const struct nand_subop *subop, + unsigned int op_id); +unsigned int nand_subop_get_data_start_off(const struct nand_subop *subop, + unsigned int op_id); +unsigned int nand_subop_get_data_len(const struct nand_subop *subop, + unsigned int op_id); /** * struct nand_op_parser_addr_constraints - Constraints for address instructions @@ -1176,9 +1208,9 @@ int nand_op_parser_exec_op(struct nand_chip *chip, * setting the read-retry mode. Mostly needed for MLC NAND. * @ecc: [BOARDSPECIFIC] ECC control structure * @buf_align: minimum buffer alignment required by a platform - * @hwcontrol: platform-specific hardware control structure + * @dummy_controller: dummy controller implementation for drivers that can + * only control a single chip * @erase: [REPLACEABLE] erase function - * @scan_bbt: [REPLACEABLE] function to scan bad block table * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring * data from array to read regs (tR). * @state: [INTERN] the current state of the NAND device @@ -1271,7 +1303,6 @@ struct nand_chip { const struct nand_operation *op, bool check_only); int (*erase)(struct mtd_info *mtd, int page); - int (*scan_bbt)(struct mtd_info *mtd); int (*set_features)(struct mtd_info *mtd, struct nand_chip *chip, int feature_addr, uint8_t *subfeature_para); int (*get_features)(struct mtd_info *mtd, struct nand_chip *chip, @@ -1314,11 +1345,11 @@ struct nand_chip { flstate_t state; uint8_t *oob_poi; - struct nand_hw_control *controller; + struct nand_controller *controller; struct nand_ecc_ctrl ecc; unsigned long buf_align; - struct nand_hw_control hwcontrol; + struct nand_controller dummy_controller; uint8_t *bbt; struct nand_bbt_descr *bbt_td; @@ -1517,14 +1548,12 @@ extern const struct nand_manufacturer_ops micron_nand_manuf_ops; extern const struct nand_manufacturer_ops amd_nand_manuf_ops; extern const struct nand_manufacturer_ops macronix_nand_manuf_ops; -int nand_default_bbt(struct mtd_info *mtd); +int nand_create_bbt(struct nand_chip *chip); int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs); int nand_isreserved_bbt(struct mtd_info *mtd, loff_t offs); int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt); int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, int allowbbt); -int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, uint8_t *buf); /** * struct platform_nand_chip - chip level device structure @@ -1555,14 +1584,12 @@ struct platform_device; * struct platform_nand_ctrl - controller level device structure * @probe: platform specific function to probe/setup hardware * @remove: platform specific function to remove/teardown hardware - * @hwcontrol: platform specific hardware control structure * @dev_ready: platform specific function to read ready/busy pin * @select_chip: platform specific chip select function * @cmd_ctrl: platform specific function for controlling * ALE/CLE/nCE. Also used to write command and address * @write_buf: platform specific function for write buffer * @read_buf: platform specific function for read buffer - * @read_byte: platform specific function to read one byte from chip * @priv: private data to transport driver specific settings * * All fields are optional and depend on the hardware driver requirements @@ -1570,13 +1597,11 @@ struct platform_device; struct platform_nand_ctrl { int (*probe)(struct platform_device *pdev); void (*remove)(struct platform_device *pdev); - void (*hwcontrol)(struct mtd_info *mtd, int cmd); int (*dev_ready)(struct mtd_info *mtd); void (*select_chip)(struct mtd_info *mtd, int chip); void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl); void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); - unsigned char (*read_byte)(struct mtd_info *mtd); void *priv; }; @@ -1593,10 +1618,10 @@ struct platform_nand_data { /* return the supported asynchronous timing mode. */ static inline int onfi_get_async_timing_mode(struct nand_chip *chip) { - if (!chip->parameters.onfi.version) + if (!chip->parameters.onfi) return ONFI_TIMING_MODE_UNKNOWN; - return chip->parameters.onfi.async_timing_mode; + return chip->parameters.onfi->async_timing_mode; } int onfi_fill_data_interface(struct nand_chip *chip, @@ -1641,14 +1666,8 @@ int nand_check_erased_ecc_chunk(void *data, int datalen, void *extraoob, int extraooblen, int threshold); -int nand_check_ecc_caps(struct nand_chip *chip, - const struct nand_ecc_caps *caps, int oobavail); - -int nand_match_ecc_req(struct nand_chip *chip, - const struct nand_ecc_caps *caps, int oobavail); - -int nand_maximize_ecc(struct nand_chip *chip, - const struct nand_ecc_caps *caps, int oobavail); +int nand_ecc_choose_conf(struct nand_chip *chip, + const struct nand_ecc_caps *caps, int oobavail); /* Default write_oob implementation */ int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip, int page); @@ -1674,10 +1693,14 @@ int nand_get_set_features_notsupp(struct mtd_info *mtd, struct nand_chip *chip, /* Default read_page_raw implementation */ int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page); +int nand_read_page_raw_notsupp(struct mtd_info *mtd, struct nand_chip *chip, + u8 *buf, int oob_required, int page); /* Default write_page_raw implementation */ int nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page); +int nand_write_page_raw_notsupp(struct mtd_info *mtd, struct nand_chip *chip, + const u8 *buf, int oob_required, int page); /* Reset and initialize a NAND device */ int nand_reset(struct nand_chip *chip, int chipnr); @@ -1711,8 +1734,13 @@ int nand_read_data_op(struct nand_chip *chip, void *buf, unsigned int len, int nand_write_data_op(struct nand_chip *chip, const void *buf, unsigned int len, bool force_8bit); -/* Free resources held by the NAND device */ +/* + * Free resources held by the NAND device, must be called on error after a + * sucessful nand_scan(). + */ void nand_cleanup(struct nand_chip *chip); +/* Unregister the MTD device and calls nand_cleanup() */ +void nand_release(struct mtd_info *mtd); /* Default extended ID decoding function */ void nand_decode_ext_id(struct nand_chip *chip); diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h index e60da0d34cc1..c922e97f205a 100644 --- a/include/linux/mtd/spi-nor.h +++ b/include/linux/mtd/spi-nor.h @@ -235,6 +235,7 @@ enum spi_nor_option_flags { SNOR_F_S3AN_ADDR_DEFAULT = BIT(3), SNOR_F_READY_XSR_RDY = BIT(4), SNOR_F_USE_CLSR = BIT(5), + SNOR_F_BROKEN_RESET = BIT(6), }; /** diff --git a/include/linux/mtd/spinand.h b/include/linux/mtd/spinand.h new file mode 100644 index 000000000000..088ff96c3eb6 --- /dev/null +++ b/include/linux/mtd/spinand.h @@ -0,0 +1,421 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2016-2017 Micron Technology, Inc. + * + * Authors: + * Peter Pan <peterpandong@micron.com> + */ +#ifndef __LINUX_MTD_SPINAND_H +#define __LINUX_MTD_SPINAND_H + +#include <linux/mutex.h> +#include <linux/bitops.h> +#include <linux/device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/spi/spi.h> +#include <linux/spi/spi-mem.h> + +/** + * Standard SPI NAND flash operations + */ + +#define SPINAND_RESET_OP \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0xff, 1), \ + SPI_MEM_OP_NO_ADDR, \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_WR_EN_DIS_OP(enable) \ + SPI_MEM_OP(SPI_MEM_OP_CMD((enable) ? 0x06 : 0x04, 1), \ + SPI_MEM_OP_NO_ADDR, \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_READID_OP(ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x9f, 1), \ + SPI_MEM_OP_NO_ADDR, \ + SPI_MEM_OP_DUMMY(ndummy, 1), \ + SPI_MEM_OP_DATA_IN(len, buf, 1)) + +#define SPINAND_SET_FEATURE_OP(reg, valptr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x1f, 1), \ + SPI_MEM_OP_ADDR(1, reg, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_DATA_OUT(1, valptr, 1)) + +#define SPINAND_GET_FEATURE_OP(reg, valptr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x0f, 1), \ + SPI_MEM_OP_ADDR(1, reg, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_DATA_IN(1, valptr, 1)) + +#define SPINAND_BLK_ERASE_OP(addr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0xd8, 1), \ + SPI_MEM_OP_ADDR(3, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_PAGE_READ_OP(addr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x13, 1), \ + SPI_MEM_OP_ADDR(3, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_PAGE_READ_FROM_CACHE_OP(fast, addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(fast ? 0x0b : 0x03, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_DUMMY(ndummy, 1), \ + SPI_MEM_OP_DATA_IN(len, buf, 1)) + +#define SPINAND_PAGE_READ_FROM_CACHE_X2_OP(addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x3b, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_DUMMY(ndummy, 1), \ + SPI_MEM_OP_DATA_IN(len, buf, 2)) + +#define SPINAND_PAGE_READ_FROM_CACHE_X4_OP(addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x6b, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_DUMMY(ndummy, 1), \ + SPI_MEM_OP_DATA_IN(len, buf, 4)) + +#define SPINAND_PAGE_READ_FROM_CACHE_DUALIO_OP(addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0xbb, 1), \ + SPI_MEM_OP_ADDR(2, addr, 2), \ + SPI_MEM_OP_DUMMY(ndummy, 2), \ + SPI_MEM_OP_DATA_IN(len, buf, 2)) + +#define SPINAND_PAGE_READ_FROM_CACHE_QUADIO_OP(addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0xeb, 1), \ + SPI_MEM_OP_ADDR(2, addr, 4), \ + SPI_MEM_OP_DUMMY(ndummy, 4), \ + SPI_MEM_OP_DATA_IN(len, buf, 4)) + +#define SPINAND_PROG_EXEC_OP(addr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x10, 1), \ + SPI_MEM_OP_ADDR(3, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_PROG_LOAD(reset, addr, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(reset ? 0x02 : 0x84, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_DATA_OUT(len, buf, 1)) + +#define SPINAND_PROG_LOAD_X4(reset, addr, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(reset ? 0x32 : 0x34, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_DATA_OUT(len, buf, 4)) + +/** + * Standard SPI NAND flash commands + */ +#define SPINAND_CMD_PROG_LOAD_X4 0x32 +#define SPINAND_CMD_PROG_LOAD_RDM_DATA_X4 0x34 + +/* feature register */ +#define REG_BLOCK_LOCK 0xa0 +#define BL_ALL_UNLOCKED 0x00 + +/* configuration register */ +#define REG_CFG 0xb0 +#define CFG_OTP_ENABLE BIT(6) +#define CFG_ECC_ENABLE BIT(4) +#define CFG_QUAD_ENABLE BIT(0) + +/* status register */ +#define REG_STATUS 0xc0 +#define STATUS_BUSY BIT(0) +#define STATUS_ERASE_FAILED BIT(2) +#define STATUS_PROG_FAILED BIT(3) +#define STATUS_ECC_MASK GENMASK(5, 4) +#define STATUS_ECC_NO_BITFLIPS (0 << 4) +#define STATUS_ECC_HAS_BITFLIPS (1 << 4) +#define STATUS_ECC_UNCOR_ERROR (2 << 4) + +struct spinand_op; +struct spinand_device; + +#define SPINAND_MAX_ID_LEN 4 + +/** + * struct spinand_id - SPI NAND id structure + * @data: buffer containing the id bytes. Currently 4 bytes large, but can + * be extended if required + * @len: ID length + * + * struct_spinand_id->data contains all bytes returned after a READ_ID command, + * including dummy bytes if the chip does not emit ID bytes right after the + * READ_ID command. The responsibility to extract real ID bytes is left to + * struct_manufacurer_ops->detect(). + */ +struct spinand_id { + u8 data[SPINAND_MAX_ID_LEN]; + int len; +}; + +/** + * struct manufacurer_ops - SPI NAND manufacturer specific operations + * @detect: detect a SPI NAND device. Every time a SPI NAND device is probed + * the core calls the struct_manufacurer_ops->detect() hook of each + * registered manufacturer until one of them return 1. Note that + * the first thing to check in this hook is that the manufacturer ID + * in struct_spinand_device->id matches the manufacturer whose + * ->detect() hook has been called. Should return 1 if there's a + * match, 0 if the manufacturer ID does not match and a negative + * error code otherwise. When true is returned, the core assumes + * that properties of the NAND chip (spinand->base.memorg and + * spinand->base.eccreq) have been filled + * @init: initialize a SPI NAND device + * @cleanup: cleanup a SPI NAND device + * + * Each SPI NAND manufacturer driver should implement this interface so that + * NAND chips coming from this vendor can be detected and initialized properly. + */ +struct spinand_manufacturer_ops { + int (*detect)(struct spinand_device *spinand); + int (*init)(struct spinand_device *spinand); + void (*cleanup)(struct spinand_device *spinand); +}; + +/** + * struct spinand_manufacturer - SPI NAND manufacturer instance + * @id: manufacturer ID + * @name: manufacturer name + * @ops: manufacturer operations + */ +struct spinand_manufacturer { + u8 id; + char *name; + const struct spinand_manufacturer_ops *ops; +}; + +/* SPI NAND manufacturers */ +extern const struct spinand_manufacturer macronix_spinand_manufacturer; +extern const struct spinand_manufacturer micron_spinand_manufacturer; +extern const struct spinand_manufacturer winbond_spinand_manufacturer; + +/** + * struct spinand_op_variants - SPI NAND operation variants + * @ops: the list of variants for a given operation + * @nops: the number of variants + * + * Some operations like read-from-cache/write-to-cache have several variants + * depending on the number of IO lines you use to transfer data or address + * cycles. This structure is a way to describe the different variants supported + * by a chip and let the core pick the best one based on the SPI mem controller + * capabilities. + */ +struct spinand_op_variants { + const struct spi_mem_op *ops; + unsigned int nops; +}; + +#define SPINAND_OP_VARIANTS(name, ...) \ + const struct spinand_op_variants name = { \ + .ops = (struct spi_mem_op[]) { __VA_ARGS__ }, \ + .nops = sizeof((struct spi_mem_op[]){ __VA_ARGS__ }) / \ + sizeof(struct spi_mem_op), \ + } + +/** + * spinand_ecc_info - description of the on-die ECC implemented by a SPI NAND + * chip + * @get_status: get the ECC status. Should return a positive number encoding + * the number of corrected bitflips if correction was possible or + * -EBADMSG if there are uncorrectable errors. I can also return + * other negative error codes if the error is not caused by + * uncorrectable bitflips + * @ooblayout: the OOB layout used by the on-die ECC implementation + */ +struct spinand_ecc_info { + int (*get_status)(struct spinand_device *spinand, u8 status); + const struct mtd_ooblayout_ops *ooblayout; +}; + +#define SPINAND_HAS_QE_BIT BIT(0) + +/** + * struct spinand_info - Structure used to describe SPI NAND chips + * @model: model name + * @devid: device ID + * @flags: OR-ing of the SPINAND_XXX flags + * @memorg: memory organization + * @eccreq: ECC requirements + * @eccinfo: on-die ECC info + * @op_variants: operations variants + * @op_variants.read_cache: variants of the read-cache operation + * @op_variants.write_cache: variants of the write-cache operation + * @op_variants.update_cache: variants of the update-cache operation + * @select_target: function used to select a target/die. Required only for + * multi-die chips + * + * Each SPI NAND manufacturer driver should have a spinand_info table + * describing all the chips supported by the driver. + */ +struct spinand_info { + const char *model; + u8 devid; + u32 flags; + struct nand_memory_organization memorg; + struct nand_ecc_req eccreq; + struct spinand_ecc_info eccinfo; + struct { + const struct spinand_op_variants *read_cache; + const struct spinand_op_variants *write_cache; + const struct spinand_op_variants *update_cache; + } op_variants; + int (*select_target)(struct spinand_device *spinand, + unsigned int target); +}; + +#define SPINAND_INFO_OP_VARIANTS(__read, __write, __update) \ + { \ + .read_cache = __read, \ + .write_cache = __write, \ + .update_cache = __update, \ + } + +#define SPINAND_ECCINFO(__ooblayout, __get_status) \ + .eccinfo = { \ + .ooblayout = __ooblayout, \ + .get_status = __get_status, \ + } + +#define SPINAND_SELECT_TARGET(__func) \ + .select_target = __func, + +#define SPINAND_INFO(__model, __id, __memorg, __eccreq, __op_variants, \ + __flags, ...) \ + { \ + .model = __model, \ + .devid = __id, \ + .memorg = __memorg, \ + .eccreq = __eccreq, \ + .op_variants = __op_variants, \ + .flags = __flags, \ + __VA_ARGS__ \ + } + +/** + * struct spinand_device - SPI NAND device instance + * @base: NAND device instance + * @spimem: pointer to the SPI mem object + * @lock: lock used to serialize accesses to the NAND + * @id: NAND ID as returned by READ_ID + * @flags: NAND flags + * @op_templates: various SPI mem op templates + * @op_templates.read_cache: read cache op template + * @op_templates.write_cache: write cache op template + * @op_templates.update_cache: update cache op template + * @select_target: select a specific target/die. Usually called before sending + * a command addressing a page or an eraseblock embedded in + * this die. Only required if your chip exposes several dies + * @cur_target: currently selected target/die + * @eccinfo: on-die ECC information + * @cfg_cache: config register cache. One entry per die + * @databuf: bounce buffer for data + * @oobbuf: bounce buffer for OOB data + * @scratchbuf: buffer used for everything but page accesses. This is needed + * because the spi-mem interface explicitly requests that buffers + * passed in spi_mem_op be DMA-able, so we can't based the bufs on + * the stack + * @manufacturer: SPI NAND manufacturer information + * @priv: manufacturer private data + */ +struct spinand_device { + struct nand_device base; + struct spi_mem *spimem; + struct mutex lock; + struct spinand_id id; + u32 flags; + + struct { + const struct spi_mem_op *read_cache; + const struct spi_mem_op *write_cache; + const struct spi_mem_op *update_cache; + } op_templates; + + int (*select_target)(struct spinand_device *spinand, + unsigned int target); + unsigned int cur_target; + + struct spinand_ecc_info eccinfo; + + u8 *cfg_cache; + u8 *databuf; + u8 *oobbuf; + u8 *scratchbuf; + const struct spinand_manufacturer *manufacturer; + void *priv; +}; + +/** + * mtd_to_spinand() - Get the SPI NAND device attached to an MTD instance + * @mtd: MTD instance + * + * Return: the SPI NAND device attached to @mtd. + */ +static inline struct spinand_device *mtd_to_spinand(struct mtd_info *mtd) +{ + return container_of(mtd_to_nanddev(mtd), struct spinand_device, base); +} + +/** + * spinand_to_mtd() - Get the MTD device embedded in a SPI NAND device + * @spinand: SPI NAND device + * + * Return: the MTD device embedded in @spinand. + */ +static inline struct mtd_info *spinand_to_mtd(struct spinand_device *spinand) +{ + return nanddev_to_mtd(&spinand->base); +} + +/** + * nand_to_spinand() - Get the SPI NAND device embedding an NAND object + * @nand: NAND object + * + * Return: the SPI NAND device embedding @nand. + */ +static inline struct spinand_device *nand_to_spinand(struct nand_device *nand) +{ + return container_of(nand, struct spinand_device, base); +} + +/** + * spinand_to_nand() - Get the NAND device embedded in a SPI NAND object + * @spinand: SPI NAND device + * + * Return: the NAND device embedded in @spinand. + */ +static inline struct nand_device * +spinand_to_nand(struct spinand_device *spinand) +{ + return &spinand->base; +} + +/** + * spinand_set_of_node - Attach a DT node to a SPI NAND device + * @spinand: SPI NAND device + * @np: DT node + * + * Attach a DT node to a SPI NAND device. + */ +static inline void spinand_set_of_node(struct spinand_device *spinand, + struct device_node *np) +{ + nanddev_set_of_node(&spinand->base, np); +} + +int spinand_match_and_init(struct spinand_device *dev, + const struct spinand_info *table, + unsigned int table_size, u8 devid); + +int spinand_upd_cfg(struct spinand_device *spinand, u8 mask, u8 val); +int spinand_select_target(struct spinand_device *spinand, unsigned int target); + +#endif /* __LINUX_MTD_SPINAND_H */ diff --git a/arch/mips/include/asm/mach-jz4740/jz4740_nand.h b/include/linux/platform_data/jz4740/jz4740_nand.h index f381d465e768..bc571f6d5ced 100644 --- a/arch/mips/include/asm/mach-jz4740/jz4740_nand.h +++ b/include/linux/platform_data/jz4740/jz4740_nand.h @@ -13,8 +13,8 @@ * */ -#ifndef __ASM_MACH_JZ4740_JZ4740_NAND_H__ -#define __ASM_MACH_JZ4740_JZ4740_NAND_H__ +#ifndef __JZ4740_NAND_H__ +#define __JZ4740_NAND_H__ #include <linux/mtd/rawnand.h> #include <linux/mtd/partitions.h> diff --git a/include/linux/platform_data/mtd-orion_nand.h b/include/linux/platform_data/mtd-orion_nand.h index a7ce77c7c1a8..34828eb85982 100644 --- a/include/linux/platform_data/mtd-orion_nand.h +++ b/include/linux/platform_data/mtd-orion_nand.h @@ -12,7 +12,6 @@ */ struct orion_nand_data { struct mtd_partition *parts; - int (*dev_ready)(struct mtd_info *mtd); u32 nr_parts; u8 ale; /* address line number connected to ALE */ u8 cle; /* address line number connected to CLE */ diff --git a/arch/mips/include/asm/txx9/ndfmc.h b/include/linux/platform_data/txx9/ndfmc.h index fa67f3df78fc..fc172627d54e 100644 --- a/arch/mips/include/asm/txx9/ndfmc.h +++ b/include/linux/platform_data/txx9/ndfmc.h @@ -5,8 +5,8 @@ * * (C) Copyright TOSHIBA CORPORATION 2007 */ -#ifndef __ASM_TXX9_NDFMC_H -#define __ASM_TXX9_NDFMC_H +#ifndef __TXX9_NDFMC_H +#define __TXX9_NDFMC_H #define NDFMC_PLAT_FLAG_USE_BSPRT 0x01 #define NDFMC_PLAT_FLAG_NO_RSTR 0x02 @@ -27,4 +27,4 @@ struct txx9ndfmc_platform_data { void txx9_ndfmc_init(unsigned long baseaddr, const struct txx9ndfmc_platform_data *plat_data); -#endif /* __ASM_TXX9_NDFMC_H */ +#endif /* __TXX9_NDFMC_H */ diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h index bb4bd15ae1f6..4fa34a227a0f 100644 --- a/include/linux/spi/spi-mem.h +++ b/include/linux/spi/spi-mem.h @@ -3,7 +3,9 @@ * Copyright (C) 2018 Exceet Electronics GmbH * Copyright (C) 2018 Bootlin * - * Author: Boris Brezillon <boris.brezillon@bootlin.com> + * Author: + * Peter Pan <peterpandong@micron.com> + * Boris Brezillon <boris.brezillon@bootlin.com> */ #ifndef __LINUX_SPI_MEM_H diff --git a/lib/Makefile b/lib/Makefile index 90dc5520b784..d4a3773ce4a6 100644 --- a/lib/Makefile +++ b/lib/Makefile @@ -116,6 +116,7 @@ obj-$(CONFIG_ZLIB_INFLATE) += zlib_inflate/ obj-$(CONFIG_ZLIB_DEFLATE) += zlib_deflate/ obj-$(CONFIG_REED_SOLOMON) += reed_solomon/ obj-$(CONFIG_BCH) += bch.o +CFLAGS_bch.o := $(call cc-option,-Wframe-larger-than=4500) obj-$(CONFIG_LZO_COMPRESS) += lzo/ obj-$(CONFIG_LZO_DECOMPRESS) += lzo/ obj-$(CONFIG_LZ4_COMPRESS) += lz4/ diff --git a/lib/bch.c b/lib/bch.c index bc89dfe4d1b3..7b0f2006698b 100644 --- a/lib/bch.c +++ b/lib/bch.c @@ -78,15 +78,22 @@ #define GF_M(_p) (CONFIG_BCH_CONST_M) #define GF_T(_p) (CONFIG_BCH_CONST_T) #define GF_N(_p) ((1 << (CONFIG_BCH_CONST_M))-1) +#define BCH_MAX_M (CONFIG_BCH_CONST_M) #else #define GF_M(_p) ((_p)->m) #define GF_T(_p) ((_p)->t) #define GF_N(_p) ((_p)->n) +#define BCH_MAX_M 15 #endif +#define BCH_MAX_T (((1 << BCH_MAX_M) - 1) / BCH_MAX_M) + #define BCH_ECC_WORDS(_p) DIV_ROUND_UP(GF_M(_p)*GF_T(_p), 32) #define BCH_ECC_BYTES(_p) DIV_ROUND_UP(GF_M(_p)*GF_T(_p), 8) +#define BCH_ECC_MAX_WORDS DIV_ROUND_UP(BCH_MAX_M * BCH_MAX_T, 32) +#define BCH_ECC_MAX_BYTES DIV_ROUND_UP(BCH_MAX_M * BCH_MAX_T, 8) + #ifndef dbg #define dbg(_fmt, args...) do {} while (0) #endif @@ -187,7 +194,8 @@ void encode_bch(struct bch_control *bch, const uint8_t *data, const unsigned int l = BCH_ECC_WORDS(bch)-1; unsigned int i, mlen; unsigned long m; - uint32_t w, r[l+1]; + uint32_t w, r[BCH_ECC_MAX_WORDS]; + const size_t r_bytes = BCH_ECC_WORDS(bch) * sizeof(*r); const uint32_t * const tab0 = bch->mod8_tab; const uint32_t * const tab1 = tab0 + 256*(l+1); const uint32_t * const tab2 = tab1 + 256*(l+1); @@ -198,7 +206,7 @@ void encode_bch(struct bch_control *bch, const uint8_t *data, /* load ecc parity bytes into internal 32-bit buffer */ load_ecc8(bch, bch->ecc_buf, ecc); } else { - memset(bch->ecc_buf, 0, sizeof(r)); + memset(bch->ecc_buf, 0, r_bytes); } /* process first unaligned data bytes */ @@ -215,7 +223,7 @@ void encode_bch(struct bch_control *bch, const uint8_t *data, mlen = len/4; data += 4*mlen; len -= 4*mlen; - memcpy(r, bch->ecc_buf, sizeof(r)); + memcpy(r, bch->ecc_buf, r_bytes); /* * split each 32-bit word into 4 polynomials of weight 8 as follows: @@ -241,7 +249,7 @@ void encode_bch(struct bch_control *bch, const uint8_t *data, r[l] = p0[l]^p1[l]^p2[l]^p3[l]; } - memcpy(bch->ecc_buf, r, sizeof(r)); + memcpy(bch->ecc_buf, r, r_bytes); /* process last unaligned bytes */ if (len) @@ -434,7 +442,7 @@ static int solve_linear_system(struct bch_control *bch, unsigned int *rows, { const int m = GF_M(bch); unsigned int tmp, mask; - int rem, c, r, p, k, param[m]; + int rem, c, r, p, k, param[BCH_MAX_M]; k = 0; mask = 1 << m; @@ -1114,7 +1122,7 @@ static int build_deg2_base(struct bch_control *bch) { const int m = GF_M(bch); int i, j, r; - unsigned int sum, x, y, remaining, ak = 0, xi[m]; + unsigned int sum, x, y, remaining, ak = 0, xi[BCH_MAX_M]; /* find k s.t. Tr(a^k) = 1 and 0 <= k < m */ for (i = 0; i < m; i++) { @@ -1254,7 +1262,6 @@ struct bch_control *init_bch(int m, int t, unsigned int prim_poly) struct bch_control *bch = NULL; const int min_m = 5; - const int max_m = 15; /* default primitive polynomials */ static const unsigned int prim_poly_tab[] = { @@ -1270,7 +1277,7 @@ struct bch_control *init_bch(int m, int t, unsigned int prim_poly) goto fail; } #endif - if ((m < min_m) || (m > max_m)) + if ((m < min_m) || (m > BCH_MAX_M)) /* * values of m greater than 15 are not currently supported; * supporting m > 15 would require changing table base type |