diff options
| -rw-r--r-- | drivers/usb/Kconfig | 1 | ||||
| -rw-r--r-- | drivers/usb/host/Kconfig | 2 | ||||
| -rw-r--r-- | drivers/usb/host/ohci-hcd.c | 5 | ||||
| -rw-r--r-- | drivers/usb/host/ohci-pnx4008.c | 476 |
4 files changed, 484 insertions, 0 deletions
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index 005043197527..f9b1719b9a37 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -25,6 +25,7 @@ config USB_ARCH_HAS_OHCI default y if PXA27x default y if ARCH_EP93XX default y if (ARCH_AT91RM9200 || ARCH_AT91SAM9261) + default y if ARCH_PNX4008 # PPC: default y if STB03xxx default y if PPC_MPC52xx diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index b93d71d28db7..77ba2b0bf0b7 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -83,6 +83,8 @@ config USB_OHCI_HCD tristate "OHCI HCD support" depends on USB && USB_ARCH_HAS_OHCI select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 + select I2C if ARCH_PNX4008 + select I2C_PNX if ARCH_PNX4008 ---help--- The Open Host Controller Interface (OHCI) is a standard for accessing USB 1.1 host controller hardware. It does more in hardware than Intel's diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index 0684f57c14a0..cbf38ae5ae76 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -940,6 +940,10 @@ MODULE_LICENSE ("GPL"); #include "ohci-at91.c" #endif +#ifdef CONFIG_ARCH_PNX4008 +#include "ohci-pnx4008.c" +#endif + #if !(defined(CONFIG_PCI) \ || defined(CONFIG_SA1111) \ || defined(CONFIG_ARCH_S3C2410) \ @@ -951,6 +955,7 @@ MODULE_LICENSE ("GPL"); || defined (CONFIG_USB_OHCI_HCD_PPC_SOC) \ || defined (CONFIG_ARCH_AT91RM9200) \ || defined (CONFIG_ARCH_AT91SAM9261) \ + || defined (CONFIG_ARCH_PNX4008) \ ) #error "missing bus glue for ohci-hcd" #endif diff --git a/drivers/usb/host/ohci-pnx4008.c b/drivers/usb/host/ohci-pnx4008.c new file mode 100644 index 000000000000..82cb22f002e7 --- /dev/null +++ b/drivers/usb/host/ohci-pnx4008.c @@ -0,0 +1,476 @@ +/* + * drivers/usb/host/ohci-pnx4008.c + * + * driver for Philips PNX4008 USB Host + * + * Authors: Dmitry Chigirev <source@mvista.com> + * Vitaly Wool <vitalywool@gmail.com> + * + * register initialization is based on code examples provided by Philips + * Copyright (c) 2005 Koninklijke Philips Electronics N.V. + * + * NOTE: This driver does not have suspend/resume functionality + * This driver is intended for engineering development purposes only + * + * 2005-2006 (c) MontaVista Software, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + */ +#include <linux/clk.h> +#include <linux/platform_device.h> +#include <linux/i2c.h> + +#include <asm/hardware.h> +#include <asm/io.h> +#include <asm/mach-types.h> + +#include <asm/arch/platform.h> +#include <asm/arch/irqs.h> +#include <asm/arch/gpio.h> + +#define USB_CTRL IO_ADDRESS(PNX4008_PWRMAN_BASE + 0x64) + +/* USB_CTRL bit defines */ +#define USB_SLAVE_HCLK_EN (1 << 24) +#define USB_HOST_NEED_CLK_EN (1 << 21) + +#define USB_OTG_CLK_CTRL IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0xFF4) +#define USB_OTG_CLK_STAT IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0xFF8) + +/* USB_OTG_CLK_CTRL bit defines */ +#define AHB_M_CLOCK_ON (1 << 4) +#define OTG_CLOCK_ON (1 << 3) +#define I2C_CLOCK_ON (1 << 2) +#define DEV_CLOCK_ON (1 << 1) +#define HOST_CLOCK_ON (1 << 0) + +#define USB_OTG_STAT_CONTROL IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0x110) + +/* USB_OTG_STAT_CONTROL bit defines */ +#define TRANSPARENT_I2C_EN (1 << 7) +#define HOST_EN (1 << 0) + +/* ISP1301 USB transceiver I2C registers */ +#define ISP1301_MODE_CONTROL_1 0x04 /* u8 read, set, +1 clear */ + +#define MC1_SPEED_REG (1 << 0) +#define MC1_SUSPEND_REG (1 << 1) +#define MC1_DAT_SE0 (1 << 2) +#define MC1_TRANSPARENT (1 << 3) +#define MC1_BDIS_ACON_EN (1 << 4) +#define MC1_OE_INT_EN (1 << 5) +#define MC1_UART_EN (1 << 6) +#define MC1_MASK 0x7f + +#define ISP1301_MODE_CONTROL_2 0x12 /* u8 read, set, +1 clear */ + +#define MC2_GLOBAL_PWR_DN (1 << 0) +#define MC2_SPD_SUSP_CTRL (1 << 1) +#define MC2_BI_DI (1 << 2) +#define MC2_TRANSP_BDIR0 (1 << 3) +#define MC2_TRANSP_BDIR1 (1 << 4) +#define MC2_AUDIO_EN (1 << 5) +#define MC2_PSW_EN (1 << 6) +#define MC2_EN2V7 (1 << 7) + +#define ISP1301_OTG_CONTROL_1 0x06 /* u8 read, set, +1 clear */ +# define OTG1_DP_PULLUP (1 << 0) +# define OTG1_DM_PULLUP (1 << 1) +# define OTG1_DP_PULLDOWN (1 << 2) +# define OTG1_DM_PULLDOWN (1 << 3) +# define OTG1_ID_PULLDOWN (1 << 4) +# define OTG1_VBUS_DRV (1 << 5) +# define OTG1_VBUS_DISCHRG (1 << 6) +# define OTG1_VBUS_CHRG (1 << 7) +#define ISP1301_OTG_STATUS 0x10 /* u8 readonly */ +# define OTG_B_SESS_END (1 << 6) +# define OTG_B_SESS_VLD (1 << 7) + +#define ISP1301_I2C_ADDR 0x2C + +#define ISP1301_I2C_MODE_CONTROL_1 0x4 +#define ISP1301_I2C_MODE_CONTROL_2 0x12 +#define ISP1301_I2C_OTG_CONTROL_1 0x6 +#define ISP1301_I2C_OTG_CONTROL_2 0x10 +#define ISP1301_I2C_INTERRUPT_SOURCE 0x8 +#define ISP1301_I2C_INTERRUPT_LATCH 0xA +#define ISP1301_I2C_INTERRUPT_FALLING 0xC +#define ISP1301_I2C_INTERRUPT_RISING 0xE +#define ISP1301_I2C_REG_CLEAR_ADDR 1 + +struct i2c_driver isp1301_driver; +struct i2c_client *isp1301_i2c_client; + +extern int usb_disabled(void); +extern int ocpi_enable(void); + +static struct clk *usb_clk; + +static int isp1301_probe(struct i2c_adapter *adap); +static int isp1301_detach(struct i2c_client *client); +static int isp1301_command(struct i2c_client *client, unsigned int cmd, + void *arg); + +static unsigned short normal_i2c[] = + { ISP1301_I2C_ADDR, ISP1301_I2C_ADDR + 1, I2C_CLIENT_END }; +static unsigned short dummy_i2c_addrlist[] = { I2C_CLIENT_END }; + +static struct i2c_client_address_data addr_data = { + .normal_i2c = normal_i2c, + .probe = dummy_i2c_addrlist, + .ignore = dummy_i2c_addrlist, +}; + +struct i2c_driver isp1301_driver = { + .id = I2C_DRIVERID_I2CDEV, /* Fake Id */ + .class = I2C_CLASS_HWMON, + .attach_adapter = isp1301_probe, + .detach_client = isp1301_detach, + .command = isp1301_command +}; + +static int isp1301_attach(struct i2c_adapter *adap, int addr, int kind) +{ + struct i2c_client *c; + + c = (struct i2c_client *)kzalloc(sizeof(*c), SLAB_KERNEL); + + if (!c) + return -ENOMEM; + + strcpy(c->name, "isp1301"); + c->flags = 0; + c->addr = addr; + c->adapter = adap; + c->driver = &isp1301_driver; + + isp1301_i2c_client = c; + + return i2c_attach_client(c); +} + +static int isp1301_probe(struct i2c_adapter *adap) +{ + return i2c_probe(adap, &addr_data, isp1301_attach); +} + +static int isp1301_detach(struct i2c_client *client) +{ + i2c_detach_client(client); + kfree(isp1301_i2c_client); + return 0; +} + +/* No commands defined */ +static int isp1301_command(struct i2c_client *client, unsigned int cmd, + void *arg) +{ + return 0; +} + +static void i2c_write(u8 buf, u8 subaddr) +{ + char tmpbuf[2]; + + tmpbuf[0] = subaddr; /*register number */ + tmpbuf[1] = buf; /*register data */ + i2c_master_send(isp1301_i2c_client, &tmpbuf[0], 2); +} + +static void isp1301_configure(void) +{ + /* PNX4008 only supports DAT_SE0 USB mode */ + /* PNX4008 R2A requires setting the MAX603 to output 3.6V */ + /* Power up externel charge-pump */ + + i2c_write(MC1_DAT_SE0 | MC1_SPEED_REG, ISP1301_I2C_MODE_CONTROL_1); + i2c_write(~(MC1_DAT_SE0 | MC1_SPEED_REG), + ISP1301_I2C_MODE_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR); + i2c_write(MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL, + ISP1301_I2C_MODE_CONTROL_2); + i2c_write(~(MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL), + ISP1301_I2C_MODE_CONTROL_2 | ISP1301_I2C_REG_CLEAR_ADDR); + i2c_write(OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN, + ISP1301_I2C_OTG_CONTROL_1); + i2c_write(~(OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN), + ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR); + i2c_write(0xFF, + ISP1301_I2C_INTERRUPT_LATCH | ISP1301_I2C_REG_CLEAR_ADDR); + i2c_write(0xFF, + ISP1301_I2C_INTERRUPT_FALLING | ISP1301_I2C_REG_CLEAR_ADDR); + i2c_write(0xFF, + ISP1301_I2C_INTERRUPT_RISING | ISP1301_I2C_REG_CLEAR_ADDR); + +} + +static inline void isp1301_vbus_on(void) +{ + i2c_write(OTG1_VBUS_DRV, ISP1301_I2C_OTG_CONTROL_1); +} + +static inline void isp1301_vbus_off(void) +{ + i2c_write(OTG1_VBUS_DRV, + ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR); +} + +static void pnx4008_start_hc(void) +{ + unsigned long tmp = __raw_readl(USB_OTG_STAT_CONTROL) | HOST_EN; + __raw_writel(tmp, USB_OTG_STAT_CONTROL); + isp1301_vbus_on(); +} + +static void pnx4008_stop_hc(void) +{ + unsigned long tmp; + isp1301_vbus_off(); + tmp = __raw_readl(USB_OTG_STAT_CONTROL) & ~HOST_EN; + __raw_writel(tmp, USB_OTG_STAT_CONTROL); +} + +static int __devinit ohci_pnx4008_start(struct usb_hcd *hcd) +{ + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + int ret; + + if ((ret = ohci_init(ohci)) < 0) + return ret; + + if ((ret = ohci_run(ohci)) < 0) { + dev_err(hcd->self.controller, "can't start\n"); + ohci_stop(hcd); + return ret; + } + return 0; +} + +static const struct hc_driver ohci_pnx4008_hc_driver = { + .description = hcd_name, + .product_desc = "pnx4008 OHCI", + + /* + * generic hardware linkage + */ + .irq = ohci_irq, + .flags = HCD_USB11 | HCD_MEMORY, + + .hcd_priv_size = sizeof(struct ohci_hcd), + /* + * basic lifecycle operations + */ + .start = ohci_pnx4008_start, + .stop = ohci_stop, + + /* + * managing i/o requests and associated device resources + */ + .urb_enqueue = ohci_urb_enqueue, + .urb_dequeue = ohci_urb_dequeue, + .endpoint_disable = ohci_endpoint_disable, + + /* + * scheduling support + */ + .get_frame_number = ohci_get_frame, + + /* + * root hub support + */ + .hub_status_data = ohci_hub_status_data, + .hub_control = ohci_hub_control, + + .start_port_reset = ohci_start_port_reset, +}; + +#define USB_CLOCK_MASK (AHB_M_CLOCK_ON| OTG_CLOCK_ON | HOST_CLOCK_ON | I2C_CLOCK_ON) + +static void pnx4008_set_usb_bits(void) +{ + start_int_set_falling_edge(SE_USB_OTG_ATX_INT_N); + start_int_ack(SE_USB_OTG_ATX_INT_N); + start_int_umask(SE_USB_OTG_ATX_INT_N); + + start_int_set_rising_edge(SE_USB_OTG_TIMER_INT); + start_int_ack(SE_USB_OTG_TIMER_INT); + start_int_umask(SE_USB_OTG_TIMER_INT); + + start_int_set_rising_edge(SE_USB_I2C_INT); + start_int_ack(SE_USB_I2C_INT); + start_int_umask(SE_USB_I2C_INT); + + start_int_set_rising_edge(SE_USB_INT); + start_int_ack(SE_USB_INT); + start_int_umask(SE_USB_INT); + + start_int_set_rising_edge(SE_USB_NEED_CLK_INT); + start_int_ack(SE_USB_NEED_CLK_INT); + start_int_umask(SE_USB_NEED_CLK_INT); + + start_int_set_rising_edge(SE_USB_AHB_NEED_CLK_INT); + start_int_ack(SE_USB_AHB_NEED_CLK_INT); + start_int_umask(SE_USB_AHB_NEED_CLK_INT); +} + +static void pnx4008_unset_usb_bits(void) +{ + start_int_mask(SE_USB_OTG_ATX_INT_N); + start_int_mask(SE_USB_OTG_TIMER_INT); + start_int_mask(SE_USB_I2C_INT); + start_int_mask(SE_USB_INT); + start_int_mask(SE_USB_NEED_CLK_INT); + start_int_mask(SE_USB_AHB_NEED_CLK_INT); +} + +static int __devinit usb_hcd_pnx4008_probe(struct platform_device *pdev) +{ + struct usb_hcd *hcd = 0; + struct ohci_hcd *ohci; + const struct hc_driver *driver = &ohci_pnx4008_hc_driver; + + int ret = 0, irq; + + dev_dbg(&pdev->dev, "%s: " DRIVER_INFO " (pnx4008)\n", hcd_name); + if (usb_disabled()) { + err("USB is disabled"); + ret = -ENODEV; + goto out; + } + + if (pdev->num_resources != 2 + || pdev->resource[0].flags != IORESOURCE_MEM + || pdev->resource[1].flags != IORESOURCE_IRQ) { + err("Invalid resource configuration"); + ret = -ENODEV; + goto out; + } + + /* Enable AHB slave USB clock, needed for further USB clock control */ + __raw_writel(USB_SLAVE_HCLK_EN | (1 << 19), USB_CTRL); + + ret = i2c_add_driver(&isp1301_driver); + if (ret < 0) { + err("failed to connect I2C to ISP1301 USB Transceiver"); + goto out; + } + + isp1301_configure(); + + /* Enable USB PLL */ + usb_clk = clk_get(&pdev->dev, "ck_pll5"); + if (IS_ERR(usb_clk)) { + err("failed to acquire USB PLL"); + ret = PTR_ERR(usb_clk); + goto out1; + } + + ret = clk_enable(usb_clk); + if (ret < 0) { + err("failed to start USB PLL"); + goto out2; + } + + ret = clk_set_rate(usb_clk, 48000); + if (ret < 0) { + err("failed to set USB clock rate"); + goto out3; + } + + __raw_writel(__raw_readl(USB_CTRL) | USB_HOST_NEED_CLK_EN, USB_CTRL); + + /* Set to enable all needed USB clocks */ + __raw_writel(USB_CLOCK_MASK, USB_OTG_CLK_CTRL); + + while ((__raw_readl(USB_OTG_CLK_STAT) & USB_CLOCK_MASK) != + USB_CLOCK_MASK) ; + + hcd = usb_create_hcd (driver, &pdev->dev, pdev->dev.bus_id); + if (!hcd) { + err("Failed to allocate HC buffer"); + ret = -ENOMEM; + goto out3; + } + + /* Set all USB bits in the Start Enable register */ + pnx4008_set_usb_bits(); + + hcd->rsrc_start = pdev->resource[0].start; + hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1; + if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { + dev_dbg(&pdev->dev, "request_mem_region failed\n"); + ret = -ENOMEM; + goto out4; + } + hcd->regs = (void __iomem *)pdev->resource[0].start; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + ret = -ENXIO; + goto out4; + } + + hcd->self.hcpriv = (void *)hcd; + + pnx4008_start_hc(); + platform_set_drvdata(pdev, hcd); + ohci = hcd_to_ohci(hcd); + ohci_hcd_init(ohci); + + dev_info(&pdev->dev, "at 0x%p, irq %d\n", hcd->regs, hcd->irq); + ret = usb_add_hcd(hcd, irq, SA_INTERRUPT); + if (ret == 0) + return ret; + + pnx4008_stop_hc(); +out4: + pnx4008_unset_usb_bits(); + usb_put_hcd(hcd); +out3: + clk_disable(usb_clk); +out2: + clk_put(usb_clk); +out1: + i2c_del_driver(&isp1301_driver); +out: + return ret; +} + +static int usb_hcd_pnx4008_remove(struct platform_device *pdev) +{ + struct usb_hcd *hcd = platform_get_drvdata(pdev); + + usb_remove_hcd(hcd); + pnx4008_stop_hc(); + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); + usb_put_hcd(hcd); + pnx4008_unset_usb_bits(); + clk_disable(usb_clk); + clk_put(usb_clk); + i2c_del_driver(&isp1301_driver); + + platform_set_drvdata(pdev, NULL); + + return 0; +} + +static struct platform_driver usb_hcd_pnx4008_driver = { + .driver = { + .name = "usb-ohci", + }, + .probe = usb_hcd_pnx4008_probe, + .remove = usb_hcd_pnx4008_remove, +}; + +static int __init usb_hcd_pnx4008_init(void) +{ + return platform_driver_register(&usb_hcd_pnx4008_driver); +} + +static void __exit usb_hcd_pnx4008_cleanup(void) +{ + return platform_driver_unregister(&usb_hcd_pnx4008_driver); +} + +module_init(usb_hcd_pnx4008_init); +module_exit(usb_hcd_pnx4008_cleanup); |