diff options
Diffstat (limited to 'Documentation/ABI/testing')
| -rw-r--r-- | Documentation/ABI/testing/debugfs-kmemtrace | 71 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-pci | 70 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-class-regulator | 57 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-fs-ext4 | 81 |
4 files changed, 270 insertions, 9 deletions
diff --git a/Documentation/ABI/testing/debugfs-kmemtrace b/Documentation/ABI/testing/debugfs-kmemtrace new file mode 100644 index 000000000000..5e6a92a02d85 --- /dev/null +++ b/Documentation/ABI/testing/debugfs-kmemtrace @@ -0,0 +1,71 @@ +What: /sys/kernel/debug/kmemtrace/ +Date: July 2008 +Contact: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro> +Description: + +In kmemtrace-enabled kernels, the following files are created: + +/sys/kernel/debug/kmemtrace/ + cpu<n> (0400) Per-CPU tracing data, see below. (binary) + total_overruns (0400) Total number of bytes which were dropped from + cpu<n> files because of full buffer condition, + non-binary. (text) + abi_version (0400) Kernel's kmemtrace ABI version. (text) + +Each per-CPU file should be read according to the relay interface. That is, +the reader should set affinity to that specific CPU and, as currently done by +the userspace application (though there are other methods), use poll() with +an infinite timeout before every read(). Otherwise, erroneous data may be +read. The binary data has the following _core_ format: + + Event ID (1 byte) Unsigned integer, one of: + 0 - represents an allocation (KMEMTRACE_EVENT_ALLOC) + 1 - represents a freeing of previously allocated memory + (KMEMTRACE_EVENT_FREE) + Type ID (1 byte) Unsigned integer, one of: + 0 - this is a kmalloc() / kfree() + 1 - this is a kmem_cache_alloc() / kmem_cache_free() + 2 - this is a __get_free_pages() et al. + Event size (2 bytes) Unsigned integer representing the + size of this event. Used to extend + kmemtrace. Discard the bytes you + don't know about. + Sequence number (4 bytes) Signed integer used to reorder data + logged on SMP machines. Wraparound + must be taken into account, although + it is unlikely. + Caller address (8 bytes) Return address to the caller. + Pointer to mem (8 bytes) Pointer to target memory area. Can be + NULL, but not all such calls might be + recorded. + +In case of KMEMTRACE_EVENT_ALLOC events, the next fields follow: + + Requested bytes (8 bytes) Total number of requested bytes, + unsigned, must not be zero. + Allocated bytes (8 bytes) Total number of actually allocated + bytes, unsigned, must not be lower + than requested bytes. + Requested flags (4 bytes) GFP flags supplied by the caller. + Target CPU (4 bytes) Signed integer, valid for event id 1. + If equal to -1, target CPU is the same + as origin CPU, but the reverse might + not be true. + +The data is made available in the same endianness the machine has. + +Other event ids and type ids may be defined and added. Other fields may be +added by increasing event size, but see below for details. +Every modification to the ABI, including new id definitions, are followed +by bumping the ABI version by one. + +Adding new data to the packet (features) is done at the end of the mandatory +data: + Feature size (2 byte) + Feature ID (1 byte) + Feature data (Feature size - 3 bytes) + + +Users: + kmemtrace-user - git://repo.or.cz/kmemtrace-user.git + diff --git a/Documentation/ABI/testing/sysfs-bus-pci b/Documentation/ABI/testing/sysfs-bus-pci index e638e15a8895..97ad190e13af 100644 --- a/Documentation/ABI/testing/sysfs-bus-pci +++ b/Documentation/ABI/testing/sysfs-bus-pci @@ -41,6 +41,49 @@ Description: for the device and attempt to bind to it. For example: # echo "8086 10f5" > /sys/bus/pci/drivers/foo/new_id +What: /sys/bus/pci/drivers/.../remove_id +Date: February 2009 +Contact: Chris Wright <chrisw@sous-sol.org> +Description: + Writing a device ID to this file will remove an ID + that was dynamically added via the new_id sysfs entry. + The format for the device ID is: + VVVV DDDD SVVV SDDD CCCC MMMM. That is Vendor ID, Device + ID, Subsystem Vendor ID, Subsystem Device ID, Class, + and Class Mask. The Vendor ID and Device ID fields are + required, the rest are optional. After successfully + removing an ID, the driver will no longer support the + device. This is useful to ensure auto probing won't + match the driver to the device. For example: + # echo "8086 10f5" > /sys/bus/pci/drivers/foo/remove_id + +What: /sys/bus/pci/rescan +Date: January 2009 +Contact: Linux PCI developers <linux-pci@vger.kernel.org> +Description: + Writing a non-zero value to this attribute will + force a rescan of all PCI buses in the system, and + re-discover previously removed devices. + Depends on CONFIG_HOTPLUG. + +What: /sys/bus/pci/devices/.../remove +Date: January 2009 +Contact: Linux PCI developers <linux-pci@vger.kernel.org> +Description: + Writing a non-zero value to this attribute will + hot-remove the PCI device and any of its children. + Depends on CONFIG_HOTPLUG. + +What: /sys/bus/pci/devices/.../rescan +Date: January 2009 +Contact: Linux PCI developers <linux-pci@vger.kernel.org> +Description: + Writing a non-zero value to this attribute will + force a rescan of the device's parent bus and all + child buses, and re-discover devices removed earlier + from this part of the device tree. + Depends on CONFIG_HOTPLUG. + What: /sys/bus/pci/devices/.../vpd Date: February 2008 Contact: Ben Hutchings <bhutchings@solarflare.com> @@ -52,3 +95,30 @@ Description: that some devices may have malformatted data. If the underlying VPD has a writable section then the corresponding section of this file will be writable. + +What: /sys/bus/pci/devices/.../virtfnN +Date: March 2009 +Contact: Yu Zhao <yu.zhao@intel.com> +Description: + This symbolic link appears when hardware supports the SR-IOV + capability and the Physical Function driver has enabled it. + The symbolic link points to the PCI device sysfs entry of the + Virtual Function whose index is N (0...MaxVFs-1). + +What: /sys/bus/pci/devices/.../dep_link +Date: March 2009 +Contact: Yu Zhao <yu.zhao@intel.com> +Description: + This symbolic link appears when hardware supports the SR-IOV + capability and the Physical Function driver has enabled it, + and this device has vendor specific dependencies with others. + The symbolic link points to the PCI device sysfs entry of + Physical Function this device depends on. + +What: /sys/bus/pci/devices/.../physfn +Date: March 2009 +Contact: Yu Zhao <yu.zhao@intel.com> +Description: + This symbolic link appears when a device is a Virtual Function. + The symbolic link points to the PCI device sysfs entry of the + Physical Function this device associates with. diff --git a/Documentation/ABI/testing/sysfs-class-regulator b/Documentation/ABI/testing/sysfs-class-regulator index 873ef1fc1569..e091fa873792 100644 --- a/Documentation/ABI/testing/sysfs-class-regulator +++ b/Documentation/ABI/testing/sysfs-class-regulator @@ -4,8 +4,8 @@ KernelVersion: 2.6.26 Contact: Liam Girdwood <lrg@slimlogic.co.uk> Description: Some regulator directories will contain a field called - state. This reports the regulator enable status, for - regulators which can report that value. + state. This reports the regulator enable control, for + regulators which can report that input value. This will be one of the following strings: @@ -14,16 +14,54 @@ Description: 'unknown' 'enabled' means the regulator output is ON and is supplying - power to the system. + power to the system (assuming no error prevents it). 'disabled' means the regulator output is OFF and is not - supplying power to the system.. + supplying power to the system (unless some non-Linux + control has enabled it). 'unknown' means software cannot determine the state, or the reported state is invalid. NOTE: this field can be used in conjunction with microvolts - and microamps to determine regulator output levels. + or microamps to determine configured regulator output levels. + + +What: /sys/class/regulator/.../status +Description: + Some regulator directories will contain a field called + "status". This reports the current regulator status, for + regulators which can report that output value. + + This will be one of the following strings: + + off + on + error + fast + normal + idle + standby + + "off" means the regulator is not supplying power to the + system. + + "on" means the regulator is supplying power to the system, + and the regulator can't report a detailed operation mode. + + "error" indicates an out-of-regulation status such as being + disabled due to thermal shutdown, or voltage being unstable + because of problems with the input power supply. + + "fast", "normal", "idle", and "standby" are all detailed + regulator operation modes (described elsewhere). They + imply "on", but provide more detail. + + Note that regulator status is a function of many inputs, + not limited to control inputs from Linux. For example, + the actual load presented may trigger "error" status; or + a regulator may be enabled by another user, even though + Linux did not enable it. What: /sys/class/regulator/.../type @@ -58,7 +96,7 @@ Description: Some regulator directories will contain a field called microvolts. This holds the regulator output voltage setting measured in microvolts (i.e. E-6 Volts), for regulators - which can report that voltage. + which can report the control input for voltage. NOTE: This value should not be used to determine the regulator output voltage level as this value is the same regardless of @@ -73,7 +111,7 @@ Description: Some regulator directories will contain a field called microamps. This holds the regulator output current limit setting measured in microamps (i.e. E-6 Amps), for regulators - which can report that current. + which can report the control input for a current limit. NOTE: This value should not be used to determine the regulator output current level as this value is the same regardless of @@ -87,7 +125,7 @@ Contact: Liam Girdwood <lrg@slimlogic.co.uk> Description: Some regulator directories will contain a field called opmode. This holds the current regulator operating mode, - for regulators which can report it. + for regulators which can report that control input value. The opmode value can be one of the following strings: @@ -101,7 +139,8 @@ Description: NOTE: This value should not be used to determine the regulator output operating mode as this value is the same regardless of - whether the regulator is enabled or disabled. + whether the regulator is enabled or disabled. A "status" + attribute may be available to determine the actual mode. What: /sys/class/regulator/.../min_microvolts diff --git a/Documentation/ABI/testing/sysfs-fs-ext4 b/Documentation/ABI/testing/sysfs-fs-ext4 new file mode 100644 index 000000000000..4e79074de282 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-fs-ext4 @@ -0,0 +1,81 @@ +What: /sys/fs/ext4/<disk>/mb_stats +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + Controls whether the multiblock allocator should + collect statistics, which are shown during the unmount. + 1 means to collect statistics, 0 means not to collect + statistics + +What: /sys/fs/ext4/<disk>/mb_group_prealloc +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + The multiblock allocator will round up allocation + requests to a multiple of this tuning parameter if the + stripe size is not set in the ext4 superblock + +What: /sys/fs/ext4/<disk>/mb_max_to_scan +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + The maximum number of extents the multiblock allocator + will search to find the best extent + +What: /sys/fs/ext4/<disk>/mb_min_to_scan +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + The minimum number of extents the multiblock allocator + will search to find the best extent + +What: /sys/fs/ext4/<disk>/mb_order2_req +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + Tuning parameter which controls the minimum size for + requests (as a power of 2) where the buddy cache is + used + +What: /sys/fs/ext4/<disk>/mb_stream_req +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + Files which have fewer blocks than this tunable + parameter will have their blocks allocated out of a + block group specific preallocation pool, so that small + files are packed closely together. Each large file + will have its blocks allocated out of its own unique + preallocation pool. + +What: /sys/fs/ext4/<disk>/inode_readahead +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + Tuning parameter which controls the maximum number of + inode table blocks that ext4's inode table readahead + algorithm will pre-read into the buffer cache + +What: /sys/fs/ext4/<disk>/delayed_allocation_blocks +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + This file is read-only and shows the number of blocks + that are dirty in the page cache, but which do not + have their location in the filesystem allocated yet. + +What: /sys/fs/ext4/<disk>/lifetime_write_kbytes +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + This file is read-only and shows the number of kilobytes + of data that have been written to this filesystem since it was + created. + +What: /sys/fs/ext4/<disk>/session_write_kbytes +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + This file is read-only and shows the number of + kilobytes of data that have been written to this + filesystem since it was mounted. |