1 files changed, 0 insertions, 60 deletions
diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt
deleted file mode 100644
index 2dcb6d12d137..000000000000
--- a/Documentation/devicetree/bindings/display/ssd1307fb.txt
+++ /dev/null
@@ -1,60 +0,0 @@
-* Solomon SSD1307 Framebuffer Driver
-
-Required properties:
-  - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for
-    now is i2c, and the supported chips are ssd1305, ssd1306, ssd1307 and
-    ssd1309.
-  - reg: Should contain address of the controller on the I2C bus. Most likely
-         0x3c or 0x3d
-  - pwm: Should contain the pwm to use according to the OF device tree PWM
-         specification [0]. Only required for the ssd1307.
-  - solomon,height: Height in pixel of the screen driven by the controller
-  - solomon,width: Width in pixel of the screen driven by the controller
-  - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is
-    mapped to.
-
-Optional properties:
-  - reset-gpios: The GPIO used to reset the OLED display, if available. See
-                 Documentation/devicetree/bindings/gpio/gpio.txt for details.
-  - vbat-supply: The supply for VBAT
-  - solomon,segment-no-remap: Display needs normal (non-inverted) data column
-                              to segment mapping
-  - solomon,col-offset: Offset of columns (COL/SEG) that the screen is mapped to.
-  - solomon,com-seq: Display uses sequential COM pin configuration
-  - solomon,com-lrremap: Display uses left-right COM pin remap
-  - solomon,com-invdir: Display uses inverted COM pin scan direction
-  - solomon,com-offset: Number of the COM pin wired to the first display line
-  - solomon,prechargep1: Length of deselect period (phase 1) in clock cycles.
-  - solomon,prechargep2: Length of precharge period (phase 2) in clock cycles.
-                         This needs to be the higher, the higher the capacitance
-                         of the OLED's pixels is
-  - solomon,dclk-div: Clock divisor 1 to 16
-  - solomon,dclk-frq: Clock frequency 0 to 15, higher value means higher
-                      frequency
-  - solomon,lookup-table: 8 bit value array of current drive pulse widths for
-                          BANK0, and colors A, B, and C. Each value in range
-                          of 31 to 63 for pulse widths of 32 to 64. Color D
-                          is always width 64.
-  - solomon,area-color-enable: Display uses color mode
-  - solomon,low-power. Display runs in low power mode
-
-[0]: Documentation/devicetree/bindings/pwm/pwm.txt
-
-Examples:
-ssd1307: oled@3c {
-        compatible = "solomon,ssd1307fb-i2c";
-        reg = <0x3c>;
-        pwms = <&pwm 4 3000>;
-        reset-gpios = <&gpio2 7>;
-};
-
-ssd1306: oled@3c {
-        compatible = "solomon,ssd1306fb-i2c";
-        reg = <0x3c>;
-        pwms = <&pwm 4 3000>;
-        reset-gpios = <&gpio2 7>;
-        solomon,com-lrremap;
-        solomon,com-invdir;
-        solomon,com-offset = <32>;
-        solomon,lookup-table = /bits/ 8 <0x3f 0x3f 0x3f 0x3f>;
-};