diff options
Diffstat (limited to 'Documentation/devicetree/bindings/dma')
7 files changed, 316 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt index c80e8a3402f0..c280a0e6f42d 100644 --- a/Documentation/devicetree/bindings/dma/atmel-dma.txt +++ b/Documentation/devicetree/bindings/dma/atmel-dma.txt @@ -24,8 +24,11 @@ The three cells in order are: 1. A phandle pointing to the DMA controller. 2. The memory interface (16 most significant bits), the peripheral interface (16 less significant bits). -3. The peripheral identifier for the hardware handshaking interface. The -identifier can be different for tx and rx. +3. Parameters for the at91 DMA configuration register which are device +dependant: + - bit 7-0: peripheral identifier for the hardware handshaking interface. The + identifier can be different for tx and rx. + - bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 1 for ASAP. Example: diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-dma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-dma.txt new file mode 100644 index 000000000000..2717ecb47db9 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/fsl-imx-dma.txt @@ -0,0 +1,48 @@ +* Freescale Direct Memory Access (DMA) Controller for i.MX + +This document will only describe differences to the generic DMA Controller and +DMA request bindings as described in dma/dma.txt . + +* DMA controller + +Required properties: +- compatible : Should be "fsl,<chip>-dma". chip can be imx1, imx21 or imx27 +- reg : Should contain DMA registers location and length +- interrupts : First item should be DMA interrupt, second one is optional and + should contain DMA Error interrupt +- #dma-cells : Has to be 1. imx-dma does not support anything else. + +Optional properties: +- #dma-channels : Number of DMA channels supported. Should be 16. +- #dma-requests : Number of DMA requests supported. + +Example: + + dma: dma@10001000 { + compatible = "fsl,imx27-dma"; + reg = <0x10001000 0x1000>; + interrupts = <32 33>; + #dma-cells = <1>; + #dma-channels = <16>; + }; + + +* DMA client + +Clients have to specify the DMA requests with phandles in a list. + +Required properties: +- dmas: List of one or more DMA request specifiers. One DMA request specifier + consists of a phandle to the DMA controller followed by the integer + specifiying the request line. +- dma-names: List of string identifiers for the DMA requests. For the correct + names, have a look at the specific client driver. + +Example: + + sdhci1: sdhci@10013000 { + ... + dmas = <&dma 7>; + dma-names = "rx-tx"; + ... + }; diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index d1e3f443e205..68cee4f5539f 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -4,14 +4,70 @@ Required properties: - compatible : Should be "fsl,<chip>-sdma" - reg : Should contain SDMA registers location and length - interrupts : Should contain SDMA interrupt +- #dma-cells : Must be <3>. + The first cell specifies the DMA request/event ID. See details below + about the second and third cell. - fsl,sdma-ram-script-name : Should contain the full path of SDMA RAM scripts firmware +The second cell of dma phandle specifies the peripheral type of DMA transfer. +The full ID of peripheral types can be found below. + + ID transfer type + --------------------- + 0 MCU domain SSI + 1 Shared SSI + 2 MMC + 3 SDHC + 4 MCU domain UART + 5 Shared UART + 6 FIRI + 7 MCU domain CSPI + 8 Shared CSPI + 9 SIM + 10 ATA + 11 CCM + 12 External peripheral + 13 Memory Stick Host Controller + 14 Shared Memory Stick Host Controller + 15 DSP + 16 Memory + 17 FIFO type Memory + 18 SPDIF + 19 IPU Memory + 20 ASRC + 21 ESAI + +The third cell specifies the transfer priority as below. + + ID transfer priority + ------------------------- + 0 High + 1 Medium + 2 Low + Examples: sdma@83fb0000 { compatible = "fsl,imx51-sdma", "fsl,imx35-sdma"; reg = <0x83fb0000 0x4000>; interrupts = <6>; + #dma-cells = <3>; fsl,sdma-ram-script-name = "sdma-imx51.bin"; }; + +DMA clients connected to the i.MX SDMA controller must use the format +described in the dma.txt file. + +Examples: + +ssi2: ssi@70014000 { + compatible = "fsl,imx51-ssi", "fsl,imx21-ssi"; + reg = <0x70014000 0x4000>; + interrupts = <30>; + clocks = <&clks 49>; + dmas = <&sdma 24 1 0>, + <&sdma 25 1 0>; + dma-names = "rx", "tx"; + fsl,fifo-depth = <15>; +}; diff --git a/Documentation/devicetree/bindings/dma/shdma.txt b/Documentation/devicetree/bindings/dma/shdma.txt new file mode 100644 index 000000000000..c15994aa1939 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/shdma.txt @@ -0,0 +1,75 @@ +* SHDMA Device Tree bindings + +Sh-/r-mobile and r-car systems often have multiple identical DMA controller +instances, capable of serving any of a common set of DMA slave devices, using +the same configuration. To describe this topology we require all compatible +SHDMA DT nodes to be placed under a DMA multiplexer node. All such compatible +DMAC instances have the same number of channels and use the same DMA +descriptors. Therefore respective DMA DT bindings can also all be placed in the +multiplexer node. Even if there is only one such DMAC instance on a system, it +still has to be placed under such a multiplexer node. + +* DMA multiplexer + +Required properties: +- compatible: should be "renesas,shdma-mux" +- #dma-cells: should be <1>, see "dmas" property below + +Optional properties (currently unused): +- dma-channels: number of DMA channels +- dma-requests: number of DMA request signals + +* DMA controller + +Required properties: +- compatible: should be "renesas,shdma" + +Example: + dmac: dma-mux0 { + compatible = "renesas,shdma-mux"; + #dma-cells = <1>; + dma-channels = <6>; + dma-requests = <256>; + reg = <0 0>; /* Needed for AUXDATA */ + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dma0: shdma@fe008020 { + compatible = "renesas,shdma"; + reg = <0xfe008020 0x270>, + <0xfe009000 0xc>; + interrupt-parent = <&gic>; + interrupts = <0 34 4 + 0 28 4 + 0 29 4 + 0 30 4 + 0 31 4 + 0 32 4 + 0 33 4>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5"; + }; + + dma1: shdma@fe018020 { + ... + }; + + dma2: shdma@fe028020 { + ... + }; + }; + +* DMA client + +Required properties: +- dmas: a list of <[DMA multiplexer phandle] [MID/RID value]> pairs, + where MID/RID values are fixed handles, specified in the SoC + manual +- dma-names: a list of DMA channel names, one per "dmas" entry + +Example: + dmas = <&dmac 0xd1 + &dmac 0xd2>; + dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/dma/ste-coh901318.txt b/Documentation/devicetree/bindings/dma/ste-coh901318.txt new file mode 100644 index 000000000000..091ad057e9cf --- /dev/null +++ b/Documentation/devicetree/bindings/dma/ste-coh901318.txt @@ -0,0 +1,32 @@ +ST-Ericsson COH 901 318 DMA Controller + +This is a DMA controller which has begun as a fork of the +ARM PL08x PrimeCell VHDL code. + +Required properties: +- compatible: should be "stericsson,coh901318" +- reg: register locations and length +- interrupts: the single DMA IRQ +- #dma-cells: must be set to <1>, as the channels on the + COH 901 318 are simple and identified by a single number +- dma-channels: the number of DMA channels handled + +Example: + +dmac: dma-controller@c00020000 { + compatible = "stericsson,coh901318"; + reg = <0xc0020000 0x1000>; + interrupt-parent = <&vica>; + interrupts = <2>; + #dma-cells = <1>; + dma-channels = <40>; +}; + +Consumers example: + +uart0: serial@c0013000 { + compatible = "..."; + (...) + dmas = <&dmac 17 &dmac 18>; + dma-names = "tx", "rx"; +}; diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt new file mode 100644 index 000000000000..bea5b73a7390 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/ste-dma40.txt @@ -0,0 +1,66 @@ +* DMA40 DMA Controller + +Required properties: +- compatible: "stericsson,dma40" +- reg: Address range of the DMAC registers +- reg-names: Names of the above areas to use during resource look-up +- interrupt: Should contain the DMAC interrupt number +- #dma-cells: must be <3> +- memcpy-channels: Channels to be used for memcpy + +Optional properties: +- dma-channels: Number of channels supported by hardware - if not present + the driver will attempt to obtain the information from H/W +- disabled-channels: Channels which can not be used + +Example: + + dma: dma-controller@801C0000 { + compatible = "stericsson,db8500-dma40", "stericsson,dma40"; + reg = <0x801C0000 0x1000 0x40010000 0x800>; + reg-names = "base", "lcpa"; + interrupt-parent = <&intc>; + interrupts = <0 25 0x4>; + + #dma-cells = <2>; + memcpy-channels = <56 57 58 59 60>; + disabled-channels = <12>; + dma-channels = <8>; + }; + +Clients +Required properties: +- dmas: Comma separated list of dma channel requests +- dma-names: Names of the aforementioned requested channels + +Each dmas request consists of 4 cells: + 1. A phandle pointing to the DMA controller + 2. Device Type + 3. The DMA request line number (only when 'use fixed channel' is set) + 4. A 32bit mask specifying; mode, direction and endianess [NB: This list will grow] + 0x00000001: Mode: + Logical channel when unset + Physical channel when set + 0x00000002: Direction: + Memory to Device when unset + Device to Memory when set + 0x00000004: Endianess: + Little endian when unset + Big endian when set + 0x00000008: Use fixed channel: + Use automatic channel selection when unset + Use DMA request line number when set + +Example: + + uart@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 0x4>; + + dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */ + <&dma 13 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "rx"; + + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt new file mode 100644 index 000000000000..9fbbdb783a72 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -0,0 +1,34 @@ +TI EDMA + +Required properties: +- compatible : "ti,edma3" +- ti,edma-regions: Number of regions +- ti,edma-slots: Number of slots +- #dma-cells: Should be set to <1> + Clients should use a single channel number per DMA request. +- dma-channels: Specify total DMA channels per CC +- reg: Memory map for accessing module +- interrupt-parent: Interrupt controller the interrupt is routed through +- interrupts: Exactly 3 interrupts need to be specified in the order: + 1. Transfer completion interrupt. + 2. Memory protection interrupt. + 3. Error interrupt. +Optional properties: +- ti,hwmods: Name of the hwmods associated to the EDMA +- ti,edma-xbar-event-map: Crossbar event to channel map + +Example: + +edma: edma@49000000 { + reg = <0x49000000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <12 13 14>; + compatible = "ti,edma3"; + ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; + #dma-cells = <1>; + dma-channels = <64>; + ti,edma-regions = <4>; + ti,edma-slots = <256>; + ti,edma-xbar-event-map = <1 12 + 2 13>; +}; |