1 files changed, 0 insertions, 93 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
deleted file mode 100644
index 0fc6700ed800..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
+++ /dev/null
@@ -1,93 +0,0 @@
-* Marvell EBU GPIO controller
-
-Required properties:
-
-- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio",
-  "marvell,armadaxp-gpio" or "marvell,armada-8k-gpio".
-
-    "marvell,orion-gpio" should be used for Orion, Kirkwood, Dove,
-    Discovery (except MV78200) and Armada 370. "marvell,mv78200-gpio"
-    should be used for the Discovery MV78200.
-
-    "marvel,armadaxp-gpio" should be used for all Armada XP SoCs
-    (MV78230, MV78260, MV78460).
-
-    "marvell,armada-8k-gpio" should be used for the Armada 7K and 8K
-    SoCs (either from AP or CP), see
-    Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
-    for specific details about the offset property.
-
-- reg: Address and length of the register set for the device. Only one
-  entry is expected, except for the "marvell,armadaxp-gpio" variant
-  for which two entries are expected: one for the general registers,
-  one for the per-cpu registers. Not used for marvell,armada-8k-gpio.
-
-- interrupts: The list of interrupts that are used for all the pins
-  managed by this GPIO bank. There can be more than one interrupt
-  (example: 1 interrupt per 8 pins on Armada XP, which means 4
-  interrupts per bank of 32 GPIOs).
-
-- interrupt-controller: identifies the node as an interrupt controller
-
-- #interrupt-cells: specifies the number of cells needed to encode an
-  interrupt source. Should be two.
-  The first cell is the GPIO number.
-  The second cell is used to specify flags:
-    bits[3:0] trigger type and level flags:
-      1 = low-to-high edge triggered.
-      2 = high-to-low edge triggered.
-      4 = active high level-sensitive.
-      8 = active low level-sensitive.
-
-- gpio-controller: marks the device node as a gpio controller
-
-- ngpios: number of GPIOs this controller has
-
-- #gpio-cells: Should be two. The first cell is the pin number. The
-  second cell is reserved for flags, unused at the moment.
-
-Optional properties:
-
-In order to use the GPIO lines in PWM mode, some additional optional
-properties are required.
-
-- compatible: Must contain "marvell,armada-370-gpio"
-
-- reg: an additional register set is needed, for the GPIO Blink
-  Counter on/off registers.
-
-- reg-names: Must contain an entry "pwm" corresponding to the
-  additional register range needed for PWM operation.
-
-- #pwm-cells: Should be two. The first cell is the GPIO line number. The
-  second cell is the period in nanoseconds.
-
-- clocks: Must be a phandle to the clock for the GPIO controller.
-
-Example:
-
-		gpio0: gpio@d0018100 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018100 0x40>,
-			    <0xd0018800 0x30>;
-			ngpios = <32>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <16>, <17>, <18>, <19>;
-		};
-
-		gpio1: gpio@18140 {
-			compatible = "marvell,armada-370-gpio";
-			reg = <0x18140 0x40>, <0x181c8 0x08>;
-			reg-names = "gpio", "pwm";
-			ngpios = <17>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			#pwm-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <87>, <88>, <89>;
-			clocks = <&coreclk 0>;
-		};