diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio')
3 files changed, 80 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/max1027-adc.txt b/Documentation/devicetree/bindings/iio/adc/max1027-adc.txt new file mode 100644 index 000000000000..a8770cc6bcad --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/max1027-adc.txt @@ -0,0 +1,22 @@ +* Maxim 1027/1029/1031 Analog to Digital Converter (ADC) + +Required properties: + - compatible: Should be "maxim,max1027" or "maxim,max1029" or "maxim,max1031" + - reg: SPI chip select number for the device + - interrupt-parent: phandle to the parent interrupt controller + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + - interrupts: IRQ line for the ADC + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "maxim,max1027"; + reg = <0>; + interrupt-parent = <&gpio5>; + interrupts = <15 IRQ_TYPE_EDGE_RISING>; + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt b/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt index 90d5f34db04e..8e191eef014e 100644 --- a/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt +++ b/Documentation/devicetree/bindings/iio/magnetometer/hmc5843.txt @@ -3,6 +3,10 @@ Required properties: - compatible : should be "honeywell,hmc5843" + Other models which are supported with driver are: + "honeywell,hmc5883" + "honeywell,hmc5883l" + "honeywell,hmc5983" - reg : the I2C address of the magnetometer - typically 0x1e Optional properties: diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt new file mode 100644 index 000000000000..a7a0a15913ad --- /dev/null +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -0,0 +1,54 @@ +STMicroelectronics MEMS sensors + +The STMicroelectronics sensor devices are pretty straight-forward I2C or +SPI devices, all sharing the same device tree descriptions no matter what +type of sensor it is. + +Required properties: +- compatible: see the list of valid compatible strings below +- reg: the I2C or SPI address the device will respond to + +Optional properties: +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor. +- vddio-supply: an optional regulator that needs to be on to provide the + VDD IO power to the sensor. +- st,drdy-int-pin: the pin on the package that will be used to signal + "data ready" (valid values: 1 or 2). This property is not configurable + on all sensors. + +Sensors may also have applicable pin control settings, those use the +standard bindings from pinctrl/pinctrl-bindings.txt. + +Valid compatible strings: + +Accelerometers: +- st,lsm303dlh-accel +- st,lsm303dlhc-accel +- st,lis3dh-accel +- st,lsm330d-accel +- st,lsm330dl-accel +- st,lsm330dlc-accel +- st,lis331dlh-accel +- st,lsm303dl-accel +- st,lsm303dlm-accel +- st,lsm330-accel + +Gyroscopes: +- st,l3g4200d-gyro +- st,lsm330d-gyro +- st,lsm330dl-gyro +- st,lsm330dlc-gyro +- st,l3gd20-gyro +- st,l3g4is-gyro +- st,lsm330-gyro + +Magnetometers: +- st,lsm303dlhc-magn +- st,lsm303dlm-magn +- st,lis3mdl-magn + +Pressure sensors: +- st,lps001wp-press +- st,lps25h-press +- st,lps331ap-press |