diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc')
11 files changed, 90 insertions, 25 deletions
diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index 31b35c3a5e47..3404afa9b938 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -9,8 +9,12 @@ Device Tree Bindings for the Arasan SDHCI Controller [4] Documentation/devicetree/bindings/phy/phy-bindings.txt Required Properties: - - compatible: Compatibility string. Must be 'arasan,sdhci-8.9a' or - 'arasan,sdhci-4.9a' or 'arasan,sdhci-5.1' + - compatible: Compatibility string. One of: + - "arasan,sdhci-8.9a": generic Arasan SDHCI 8.9a PHY + - "arasan,sdhci-4.9a": generic Arasan SDHCI 4.9a PHY + - "arasan,sdhci-5.1": generic Arasan SDHCI 5.1 PHY + - "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1": rk3399 eMMC PHY + For this device it is strongly suggested to include arasan,soc-ctl-syscon. - reg: From mmc bindings: Register location and length. - clocks: From clock bindings: Handles to clock inputs. - clock-names: From clock bindings: Tuple including "clk_xin" and "clk_ahb" @@ -22,6 +26,17 @@ Required Properties for "arasan,sdhci-5.1": - phys: From PHY bindings: Phandle for the Generic PHY for arasan. - phy-names: MUST be "phy_arasan". +Optional Properties: + - arasan,soc-ctl-syscon: A phandle to a syscon device (see ../mfd/syscon.txt) + used to access core corecfg registers. Offsets of registers in this + syscon are determined based on the main compatible string for the device. + - clock-output-names: If specified, this will be the name of the card clock + which will be exposed by this device. Required if #clock-cells is + specified. + - #clock-cells: If specified this should be the value <0>. With this property + in place we will export a clock representing the Card Clock. This clock + is expected to be consumed by our PHY. You must also specify + Example: sdhci@e0100000 { compatible = "arasan,sdhci-8.9a"; @@ -42,3 +57,19 @@ Example: phys = <&emmc_phy>; phy-names = "phy_arasan"; } ; + + sdhci: sdhci@fe330000 { + compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1"; + reg = <0x0 0xfe330000 0x0 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_EMMC>, <&cru ACLK_EMMC>; + clock-names = "clk_xin", "clk_ahb"; + arasan,soc-ctl-syscon = <&grf>; + assigned-clocks = <&cru SCLK_EMMC>; + assigned-clock-rates = <200000000>; + clock-output-names = "emmc_cardclock"; + phys = <&emmc_phy>; + phy-names = "phy_arasan"; + #clock-cells = <0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt deleted file mode 100644 index 59476fbdbfa1..000000000000 --- a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt +++ /dev/null @@ -1,18 +0,0 @@ -Broadcom BCM2835 SDHCI controller - -This file documents differences between the core properties described -by mmc.txt and the properties that represent the BCM2835 controller. - -Required properties: -- compatible : Should be "brcm,bcm2835-sdhci". -- clocks : The clock feeding the SDHCI controller. - -Example: - -sdhci: sdhci { - compatible = "brcm,bcm2835-sdhci"; - reg = <0x7e300000 0x100>; - interrupts = <2 30>; - clocks = <&clk_mmc>; - bus-width = <4>; -}; diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm7425-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm7425-sdhci.txt new file mode 100644 index 000000000000..82847174c37d --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,bcm7425-sdhci.txt @@ -0,0 +1,36 @@ +* BROADCOM BRCMSTB/BMIPS SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-brcmstb driver. + +NOTE: The driver disables all UHS speed modes by default and depends +on Device Tree properties to enable them for SoC/Board combinations +that support them. + +Required properties: +- compatible: "brcm,bcm7425-sdhci" + +Refer to clocks/clock-bindings.txt for generic clock consumer properties. + +Example: + + sdhci@f03e0100 { + compatible = "brcm,bcm7425-sdhci"; + reg = <0xf03e0000 0x100>; + interrupts = <0x0 0x26 0x0>; + sdhci,auto-cmd12; + clocks = <&sw_sdio>; + sd-uhs-sdr50; + sd-uhs-ddr50; + }; + + sdhci@f03e0300 { + non-removable; + bus-width = <0x8>; + compatible = "brcm,bcm7425-sdhci"; + reg = <0xf03e0200 0x100>; + interrupts = <0x0 0x27 0x0>; + sdhci,auto-cmd12; + clocks = <sw_sdio>; + mmc-hs200-1_8v; + }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index dca56d6248f5..3e29050ec769 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -28,6 +28,8 @@ Optional properties: transparent level shifters on the outputs of the controller. Two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). Several ranges could be specified. +- fsl,tuning-start-tap: Specify the start dealy cell point when send first CMD19 + in tuning procedure. - fsl,tuning-step: Specify the increasing delay cell steps in tuning procedure. The uSDHC use one delay cell as default increasing step to do tuning process. This property allows user to change the tuning step to more than one delay diff --git a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt index 71ad57e050b1..3149297b3933 100644 --- a/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt +++ b/Documentation/devicetree/bindings/mmc/microchip,sdhci-pic32.txt @@ -20,7 +20,7 @@ Example: compatible = "microchip,pic32mzda-sdhci"; reg = <0x1f8ec000 0x100>; interrupts = <191 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&REFCLKO4>, <&PBCLK5>; + clocks = <&rootclk REF4CLK>, <&rootclk PB5CLK>; clock-names = "base_clk", "sys_clk"; bus-width = <4>; cap-sd-highspeed; diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt index 0cb827bf9435..3d965d57e00b 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt @@ -1,7 +1,7 @@ * The simple eMMC hardware reset provider The purpose of this driver is to perform standard eMMC hw reset -procedure, as descibed by Jedec 4.4 specification. This procedure is +procedure, as described by Jedec 4.4 specification. This procedure is performed just after MMC core enabled power to the given mmc host (to fix possible issues if bootloader has left eMMC card in initialized or unknown state), and before performing complete system reboot (also in diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index ed23b9bedfdc..22d1e1f3f38b 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -46,8 +46,12 @@ Optional properties: - mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported - mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported - mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported +- mmc-hs400-enhanced-strobe: eMMC HS400 enhanced strobe mode is supported - dsr: Value the card's (optional) Driver Stage Register (DSR) should be programmed with. Valid range: [0 .. 0xffff]. +- no-sdio: controller is limited to send sdio cmd during initialization +- no-sd: controller is limited to send sd cmd during initialization +- no-mmc: controller is limited to send mmc cmd during initialization *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index ea5614b6f613..07184e8f894e 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -15,6 +15,7 @@ Required Properties: - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 + - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 Optional Properties: * clocks: from common clock binding: if ciu_drive and ciu_sample are diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 18d950df2749..3cd4c43a3260 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -10,7 +10,7 @@ Required properties: subsystem (mmcss) inside the FlashSS (available in STiH407 SoC family). -- clock-names: Should be "mmc". +- clock-names: Should be "mmc" and "icn". (NB: The latter is not compulsory) See: Documentation/devicetree/bindings/resource-names.txt - clocks: Phandle to the clock. See: Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -38,7 +38,7 @@ Optional properties: - bus-width: Number of data lines. See: Documentation/devicetree/bindings/mmc/mmc.txt. -- max-frequency: Can be 200MHz, 100Mz or 50MHz (default) and used for +- max-frequency: Can be 200MHz, 100Mz or 50MHz (default) and used for configuring the CCONFIG3 in the mmcss. See: Documentation/devicetree/bindings/mmc/mmc.txt. @@ -48,7 +48,7 @@ Optional properties: - vqmmc-supply: Phandle to the regulator dt node, mentioned as the vcc/vdd supply in eMMC/SD specs. -- sd-uhs--sdr50: To enable the SDR50 in the mmcss. +- sd-uhs-sdr50: To enable the SDR50 in the mmcss. See: Documentation/devicetree/bindings/mmc/mmc.txt. - sd-uhs-sdr104: To enable the SDR104 in the mmcss. diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 7fb746dd1a68..0f610d4b5b00 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -26,3 +26,6 @@ Required properties: Optional properties: - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable +- pinctrl-names: should be "default", "state_uhs" +- pinctrl-0: should contain default/high speed pin ctrl +- pinctrl-1: should contain uhs mode pin ctrl diff --git a/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt b/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt index 8babdaa8623b..6d1b7971d078 100644 --- a/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt +++ b/Documentation/devicetree/bindings/mmc/usdhi6rol0.txt @@ -12,6 +12,12 @@ Optional properties: - vmmc-supply: a phandle of a regulator, supplying Vcc to the card - vqmmc-supply: a phandle of a regulator, supplying VccQ to the card +- pinctrl-names: Can contain a "default" entry and a "state_uhs" + entry. The state_uhs entry is used together with the default + entry when the board requires distinct settings for UHS speeds. + +- pinctrl-N: One property for each name listed in pinctrl-names, see + ../pinctrl/pinctrl-bindings.txt. Additionally any standard mmc bindings from mmc.txt can be used. |