diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc')
9 files changed, 99 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt new file mode 100644 index 000000000000..7f95ec400863 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt @@ -0,0 +1,32 @@ +Amlogic SD / eMMC controller for S905/GXBB family SoCs + +The MMC 5.1 compliant host controller on Amlogic provides the +interface for SD, eMMC and SDIO devices. + +This file documents the properties in addition to those available in +the MMC core bindings, documented by mmc.txt. + +Required properties: +- compatible : contains one of: + - "amlogic,meson-gx-mmc" + - "amlogic,meson-gxbb-mmc" + - "amlogic,meson-gxl-mmc" + - "amlogic,meson-gxm-mmc" +- clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names. +- clock-names: Should contain the following: + "core" - Main peripheral bus clock + "clkin0" - Parent clock of internal mux + "clkin1" - Other parent clock of internal mux + The driver has an interal mux clock which switches between clkin0 and clkin1 depending on the + clock rate requested by the MMC core. + +Example: + + sd_emmc_a: mmc@70000 { + compatible = "amlogic,meson-gxbb-mmc"; + reg = <0x0 0x70000 0x0 0x2000>; + interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; + pinctrl-0 = <&emmc_pins>; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt index be56d2bd474a..954561d09a8e 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt @@ -7,6 +7,15 @@ Required properties: - compatible : Should be one of the following "brcm,bcm2835-sdhci" "brcm,sdhci-iproc-cygnus" + "brcm,sdhci-iproc" + +Use brcm2835-sdhci for Rasperry PI. + +Use sdhci-iproc-cygnus for Broadcom SDHCI Controllers +restricted to 32bit host accesses to SDHCI registers. + +Use sdhci-iproc for Broadcom SDHCI Controllers that allow standard +8, 16, 32-bit host access to SDHCI register. - clocks : The clock feeding the SDHCI controller. diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index ff611fa66871..e4ba92aa035e 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -8,11 +8,14 @@ Required properties: - compatible: should be "renesas,mmcif-<soctype>", "renesas,sh-mmcif" as a fallback. Examples with <soctype> are: + - "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs + - "renesas,mmcif-r8a7778" for the MMCIF found in r8a7778 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs - "renesas,mmcif-r8a7793" for the MMCIF found in r8a7793 SoCs - "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs + - "renesas,mmcif-sh73a0" for the MMCIF found in sh73a0 SoCs - clocks: reference to the functional clock diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index 07184e8f894e..ea9c1c9607f6 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -13,6 +13,7 @@ Required Properties: - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following, before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 + - "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK1108 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 diff --git a/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt new file mode 100644 index 000000000000..c0f37cb41a9b --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt @@ -0,0 +1,32 @@ +* Cadence SD/SDIO/eMMC Host Controller + +Required properties: +- compatible: should be one of the following: + "cdns,sd4hc" - default of the IP + "socionext,uniphier-sd4hc" - for Socionext UniPhier SoCs +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: phandle to the input clock. + +Optional properties: +For eMMC configuration, supported speed modes are not indicated by the SDHCI +Capabilities Register. Instead, the following properties should be specified +if supported. See mmc.txt for details. +- mmc-ddr-1_8v +- mmc-ddr-1_2v +- mmc-hs200-1_8v +- mmc-hs200-1_2v +- mmc-hs400-1_8v +- mmc-hs400-1_2v + +Example: + emmc: sdhci@5a000000 { + compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; + reg = <0x5a000000 0x400>; + interrupts = <0 78 4>; + clocks = <&clk 4>; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + }; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt index 485483a63d8c..0576264eab5e 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt @@ -17,6 +17,7 @@ Required properties: "iface" - Main peripheral bus clock (PCLK/HCLK - AHB Bus clock) (required) "core" - SDC MMC clock (MCLK) (required) "bus" - SDCC bus voter clock (optional) + "xo" - TCXO clock (optional) Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci.txt b/Documentation/devicetree/bindings/mmc/sdhci.txt new file mode 100644 index 000000000000..1c95a1a555c3 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci.txt @@ -0,0 +1,13 @@ +The properties specific for SD host controllers. For properties shared by MMC +host controllers refer to the mmc[1] bindings. + + [1] Documentation/devicetree/bindings/mmc/mmc.txt + +Optional properties: +- sdhci-caps-mask: The sdhci capabilities register is incorrect. This 64bit + property corresponds to the bits in the sdhci capabilty register. If the bit + is on in the mask then the bit is incorrect in the register and should be + turned off, before applying sdhci-caps. +- sdhci-caps: The sdhci capabilities register is incorrect. This 64bit + property corresponds to the bits in the sdhci capability register. If the + bit is on in the property then the bit should be turned on. diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 4e00e859e885..7fd17c3da116 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -43,6 +43,9 @@ Optional properties: reset signal present internally in some host controller IC designs. See Documentation/devicetree/bindings/reset/reset.txt for details. +* reset-names: request name for using "resets" property. Must be "reset". + (It will be used together with "resets" property.) + * clocks: from common clock binding: handle to biu and ciu clocks for the bus interface unit clock and the card interface unit clock. @@ -56,8 +59,9 @@ Optional properties: is specified and the ciu clock is specified then we'll try to set the ciu clock to this at probe time. -* clock-freq-min-max: Minimum and Maximum clock frequency for card output +* clock-freq-min-max (DEPRECATED): Minimum and Maximum clock frequency for card output clock(cclk_out). If it's not specified, max is 200MHZ and min is 400KHz by default. + (Use the "max-frequency" instead of "clock-freq-min-max".) * num-slots: specifies the number of slots supported by the controller. The number of physical slots actually used could be equal or less than the @@ -71,11 +75,6 @@ Optional properties: * card-detect-delay: Delay in milli-seconds before detecting card after card insert event. The default value is 0. -* supports-highspeed (DEPRECATED): Enables support for high speed cards (up to 50MHz) - (use "cap-mmc-highspeed" or "cap-sd-highspeed" instead) - -* broken-cd: as documented in mmc core bindings. - * vmmc-supply: The phandle to the regulator to use for vmmc. If this is specified we'll defer probe until we can find this regulator. @@ -103,6 +102,8 @@ board specific portions as listed below. interrupts = <0 75 0>; #address-cells = <1>; #size-cells = <0>; + resets = <&rst 20>; + reset-names = "reset"; }; [board specific internal DMA resources] diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 13df9c2399c3..a1650edfd2b7 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -11,8 +11,8 @@ optional bindings can be used. Required properties: - compatible: "renesas,sdhi-shmobile" - a generic sh-mobile SDHI unit - "renesas,sdhi-sh7372" - SDHI IP on SH7372 SoC "renesas,sdhi-sh73a0" - SDHI IP on SH73A0 SoC + "renesas,sdhi-r7s72100" - SDHI IP on R7S72100 SoC "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC "renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC |