diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt | 186 |
1 files changed, 0 insertions, 186 deletions
diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt deleted file mode 100644 index 44335a4f8bfb..000000000000 --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt +++ /dev/null @@ -1,186 +0,0 @@ -* Broadcom STB NAND Controller - -The Broadcom Set-Top Box NAND controller supports low-level access to raw NAND -flash chips. It has a memory-mapped register interface for both control -registers and for its data input/output buffer. On some SoCs, this controller is -paired with a custom DMA engine (inventively named "Flash DMA") which supports -basic PROGRAM and READ functions, among other features. - -This controller was originally designed for STB SoCs (BCM7xxx) but is now -available on a variety of Broadcom SoCs, including some BCM3xxx, BCM63xx, and -iProc/Cygnus. Its history includes several similar (but not fully register -compatible) versions. - -Required properties: -- compatible : May contain an SoC-specific compatibility string (see below) - to account for any SoC-specific hardware bits that may be - added on top of the base core controller. - In addition, must contain compatibility information about - the core NAND controller, of the following form: - "brcm,brcmnand" and an appropriate version compatibility - string, like "brcm,brcmnand-v7.0" - Possible values: - brcm,brcmnand-v2.1 - brcm,brcmnand-v2.2 - brcm,brcmnand-v4.0 - brcm,brcmnand-v5.0 - brcm,brcmnand-v6.0 - brcm,brcmnand-v6.1 - brcm,brcmnand-v6.2 - brcm,brcmnand-v7.0 - brcm,brcmnand-v7.1 - brcm,brcmnand-v7.2 - brcm,brcmnand-v7.3 - brcm,brcmnand -- reg : the register start and length for NAND register region. - (optional) Flash DMA register range (if present) - (optional) NAND flash cache range (if at non-standard offset) -- reg-names : a list of the names corresponding to the previous register - ranges. Should contain "nand" and (optionally) - "flash-dma" or "flash-edu" and/or "nand-cache". -- interrupts : The NAND CTLRDY interrupt, (if Flash DMA is available) - FLASH_DMA_DONE and if EDU is avaialble and used FLASH_EDU_DONE -- interrupt-names : May be "nand_ctlrdy" or "flash_dma_done" or "flash_edu_done", - if broken out as individual interrupts. - May be "nand", if the SoC has the individual NAND - interrupts multiplexed behind another custom piece of - hardware -- #address-cells : <1> - subnodes give the chip-select number -- #size-cells : <0> - -Optional properties: -- clock : reference to the clock for the NAND controller -- clock-names : "nand" (required for the above clock) -- brcm,nand-has-wp : Some versions of this IP include a write-protect - (WP) control bit. It is always available on >= - v7.0. Use this property to describe the rare - earlier versions of this core that include WP - - -- Additional SoC-specific NAND controller properties -- - -The NAND controller is integrated differently on the variety of SoCs on which it -is found. Part of this integration involves providing status and enable bits -with which to control the 8 exposed NAND interrupts, as well as hardware for -configuring the endianness of the data bus. On some SoCs, these features are -handled via standard, modular components (e.g., their interrupts look like a -normal IRQ chip), but on others, they are controlled in unique and interesting -ways, sometimes with registers that lump multiple NAND-related functions -together. The former case can be described simply by the standard interrupts -properties in the main controller node. But for the latter exceptional cases, -we define additional 'compatible' properties and associated register resources within the NAND controller node above. - - - compatible: Can be one of several SoC-specific strings. Each SoC may have - different requirements for its additional properties, as described below each - bullet point below. - - * "brcm,nand-bcm63138" - - reg: (required) the 'NAND_INT_BASE' register range, with separate status - and enable registers - - reg-names: (required) "nand-int-base" - - * "brcm,nand-bcm6368" - - compatible: should contain "brcm,nand-bcm<soc>", "brcm,nand-bcm6368" - - reg: (required) the 'NAND_INTR_BASE' register range, with combined status - and enable registers, and boot address registers - - reg-names: (required) "nand-int-base" - - * "brcm,nand-iproc" - - reg: (required) the "IDM" register range, for interrupt enable and APB - bus access endianness configuration, and the "EXT" register range, - for interrupt status/ack. - - reg-names: (required) a list of the names corresponding to the previous - register ranges. Should contain "iproc-idm" and "iproc-ext". - - -* NAND chip-select - -Each controller (compatible: "brcm,brcmnand") may contain one or more subnodes -to represent enabled chip-selects which (may) contain NAND flash chips. Their -properties are as follows. - -Required properties: -- compatible : should contain "brcm,nandcs" -- reg : a single integer representing the chip-select - number (e.g., 0, 1, 2, etc.) -- #address-cells : see partition.txt -- #size-cells : see partition.txt - -Optional properties: -- nand-ecc-strength : see nand-controller.yaml -- nand-ecc-step-size : must be 512 or 1024. See nand-controller.yaml -- nand-on-flash-bbt : boolean, to enable the on-flash BBT for this - chip-select. See nand-controller.yaml -- brcm,nand-oob-sector-size : integer, to denote the spare area sector size - expected for the ECC layout in use. This size, in - addition to the strength and step-size, - determines how the hardware BCH engine will lay - out the parity bytes it stores on the flash. - This property can be automatically determined by - the flash geometry (particularly the NAND page - and OOB size) in many cases, but when booting - from NAND, the boot controller has only a limited - number of available options for its default ECC - layout. - -Each nandcs device node may optionally contain sub-nodes describing the flash -partition mapping. See partition.txt for more detail. - - -Example: - -nand@f0442800 { - compatible = "brcm,brcmnand-v7.0", "brcm,brcmnand"; - reg = <0xF0442800 0x600>, - <0xF0443000 0x100>; - reg-names = "nand", "flash-dma"; - interrupt-parent = <&hif_intr2_intc>; - interrupts = <24>, <4>; - - #address-cells = <1>; - #size-cells = <0>; - - nandcs@1 { - compatible = "brcm,nandcs"; - reg = <1>; // Chip select 1 - nand-on-flash-bbt; - nand-ecc-strength = <12>; - nand-ecc-step-size = <512>; - - // Partitions - #address-cells = <1>; // <2>, for 64-bit offset - #size-cells = <1>; // <2>, for 64-bit length - flash0.rootfs@0 { - reg = <0 0x10000000>; - }; - flash0@0 { - reg = <0 0>; // MTDPART_SIZ_FULL - }; - flash0.kernel@10000000 { - reg = <0x10000000 0x400000>; - }; - }; -}; - -nand@10000200 { - compatible = "brcm,nand-bcm63168", "brcm,nand-bcm6368", - "brcm,brcmnand-v4.0", "brcm,brcmnand"; - reg = <0x10000200 0x180>, - <0x10000600 0x200>, - <0x100000b0 0x10>; - reg-names = "nand", "nand-cache", "nand-int-base"; - interrupt-parent = <&periph_intc>; - interrupts = <50>; - clocks = <&periph_clk 20>; - clock-names = "nand"; - - #address-cells = <1>; - #size-cells = <0>; - - nand0: nandcs@0 { - compatible = "brcm,nandcs"; - reg = <0>; - nand-on-flash-bbt; - nand-ecc-strength = <1>; - nand-ecc-step-size = <512>; - }; -}; |